SDI OUTPUT BOARD

BKP-7311

INSTALLATION MANUAL1st Edition

BKP-7311 IM

! WARNINGThis manual is intended for qualified service personnel only.To reduce the risk of electric shock, fire or injury, do not perform any servicing other than thatcontained in the operating instructions unless you are qualified to do so. Refer all servicing toqualified service personnel.

! WARNUNGDie Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um dieGefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind beiWartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegebenWartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigungdazu besitzen.

! AVERTISSEMENTCe manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afinde réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que lesréparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.Pour toute réparation faire appel à une personne compétente uniquement.

1BKP-7311 IM

/Table of Contents

1.

1-1. ....................................................................................................... 1-1 (J)

1-2. .................................................................... 1-1 (J)

1-3. .......................................................................... 1-2 (J)

1-4. ......................................................................................... 1-5 (J)

1. Installation

1-1. General ..................................................................................................1-1 (E)

1-2. Function of Switches on AD Board ......................................................1-1 (E)

1-3. Installation of BKP-7311 ......................................................................1-2 (E)

1-4. System Adjustment ...............................................................................1-5 (E)

1-1 (E)BKP-7311 IM

AD

CN1 CN2

RV2231 RV2131 RV2031

E2031E1781

E3071

TP3071

TP2231

TP2131 TP2031

RV3541 RV3351

TP3352TP3351S1601

RV3211

RV3213

RV3354RV3355

TP3542

TP3541

RV3544

RV3545

RV3214

TP3211

E3211

TP1991

TP1992

TP2742TP2743

E2801TP2741

TP1781

RV2771

TP2694TP2691

TP2402

S2961

S2963S2962

CN2032

E2441

TP2401S2441

TP2693TP2692

TP1601

E2691

RV1381

CN3

RV1021 RV821RV581

RV371RV1181S2442(CN2541)

RV2541TP2542TP2541

RV2032RV2132

RV3212

RV3352RV3542

RV2232

S1603 S1602

-12 -5 +5 +12CAUTION SDI CABLE

OUTPUTA B C Y B-YR-Y

BLACKBALANCE

RETURN

B&W COLOR

CHU RET1/RET2LINE SELECT

RET1/RET2RET3/RET4

Y B-YR-YANALOG

BLACKBALANCE

ON

OFFON

OFF

ON

OFF

ON

Section 1Installation

1-1. General

BKP-7311 is the board kit that has a function of colorcorrector and D1 format serial digital output. When thisboard kit is installed into CCU-700A/CCU-700AP CameraControl Unit, BVP-700/700P system can operate in D1format serial digital system.

1-2. Function of Switches on AD Board

. S1601 (TEST ON/OFF)Turn on when perfoeming the adjustment of analogsignal system for AD-117 board.(Refer to Section 2 “Alignment” of the maintenancemanual.)Factory-setting : OFF

. S1602 (CHU RET1/2 LINE)Selects an output signal to be output to viewfinder, whenselecting the RET1/RET2 switch of BVP.The output signal is as follows.

S1602/AD-117 RET SW/BVP Output signal for VF

RET1/RET2 RET1 RET1RET2 RET2

RET3/RET4 RET1 RET3RET2 RET4

Factory-setting : RET1/RET2

. S1603 (Digital RET BW/COLOR)Selects B&W or COLOR as the DIGITAL RET signalwhen DA-101 board (BKP-7312) is installed in CCU.Factory-setting : COLOR

. S2442 (SDI ON/OFF)Turn off when performing the adjustment of SDI Free-Run frequency.(Refer to Section 2-5-1 “SDI Free-Run Frequencyadjustment”of the maintenance manual.)Factory-setting : ON

. S2961 (SDI TEST ON/OFF)Turn on to output a test signal which is selected byS2962 at SERIAL OUTPUT connector of CCU.Factory-setting : OFF

. S2963 (REMOTE ON/OFF)Selects an output signal at SERIAL OUTPUT connectorof CCU.ON : Outputs test signal which is selected by S2962OFF : Outputs COLOR-BAR signal from VA-156

which is analog-to-digital converted in ADboard.

Factory-setting : ON

. S2962 (D1 BAR MODE)Selects the TEST signal to be output at SERIAL OUT-PUT connector of CCU.

S2962 TEST SIGNAL_____1 _____2 _____3

OFF OFF ON 75% COLOR BAR

ON OFF ON 100% COLOR BAR

OFF ON ON BLACK BURST

ON ON ON MULTI BURST

– – OFF WORST PATTERN

nS2962-4 is not used.

1-2 (E) BKP-7311 IM

Power unit

Screws(PWH4 x 10)

Screws(PWH4 x 10)

Front panel

Plug-inboards

Unlock Unlock

1-3. Installation of BKP-7311

1. Disconnect the power cord from the rear panel ofCCU-700A. Loosen the two screws (M4 x 20) andremove the front panel.

2. Push and turn the eject levers to unlock and pull out allthe plug-in boards from the unit.

3. Loosen the four screws (PWH4 x 10) fixing the powerunit and remove the power unit while pushing thepower unit forward at the fan in the rear of the unit.

4. Remove the six screws (B3 x 5) and open the rearpanel. Disconnect the flexible card wire from CN3 onthe rear panel.

5. Install the three coaxial cables into the suppliedharness guide.

1-3. Installation of BKP-7311

Flexible card wire

MB-563 board

B3 x 5

B3 x 5

B3 x 5

Rear panel

CN-3

Coaxial cables

Harness guide

1-3 (E)BKP-7311 IM

Coaxial cables

150mm

Hole

Coaxial cables

Harness guide

Lockingcompound

Nat plateHarness guide

6. Hook the harness guide onto the rail plate and push itin the direction of the arrow.

7. Apply locking compound to the thread part, thentighten screw to install the supplied nut plate.

8. Pass the three coaxial cables through the hole on theMB-563.

9. Extract the three coaxial cables from the front sideabout 150 mm as shown in the figure.

10. Hold the coaxial cables using a supplied harnessclamp.

11. Connect the three coaxial cables to the rear panel.Connect the flexible card wire removed in step 4 toCN3.nIf it is difficult to connect the coaxial cables, removethe CN-1036 board on the rear panel, and then connectthem.When installing the board, apply locking compound tothe four screws.

1-3. Installation of BKP-7311

CN-1036 board

Rear panel

MB-563 board

Flexible card wirePWH3 x 6

B3 x 5B3 x 5

Cable clamp

1-4 (E) BKP-7311 IM

BKP-7311

Coaxial cables

Lock

Plug-in boards

DM

AT

VA

Power unit

Screws(PWH4 x 10)

Screws (PWH4 x 10)

2

1

12. Tighten screws 1 and 2 shown in the figure, thentighten the remaining four screws to install the rearpanel.

13. Install the power unit in the unit with four screws.

14. Insert the plug-in boards removed in step 2 in the unitin the reverse procedures of removal.

15. Insert the BKP-7311 in the unit,and connect the threecoaxial cables to the BKP-7311.nThe same signal is output at connectors CN2571,CN2572 and CN2581. Coaxial cables can be connect-ed to every connector.

1-3. Installation of BKP-7311

1-5 (E)BKP-7311 IM

16. Tighten the two screws (M4 x 20) on the front panelto install the front panel.

1-3. Installation of BKP-73111-4. System Adjustment

M4 x 20

M4 x 20Front panel

1-4. System Adjustment

Perform the adjustment of VA-156A board in CCU-700A(VA-156P board in CCU-700AP) as follows.

Turn on the power of CCU-700A/700AP, and then adjustthe VA-156A board in CCU-700A (VA-156P board inCCU-700AP) making sure that the signal of camera shouldbe stable.Extend VA-156A/156P board with BKP-7900 ExtensionBoard.

Adjustment ProcedureAdjust the camera H phase as shown below.Equipment : Oscilloscope (CHOP mode)To be extended : VA-156A/156P boardTest point : CH1 pin A36/extension board

CH2 pin C18/extension boardAdjustment point : 1RV1892/VA-156A (VA-156P)

boardSpecifications : T = 0.35 ±0.10 µs

50 %

50 %CH-2

T

CH-1

BKP-7311 IM

The material contained in this manual consists ofinformation that is the property of Sony Corporation andis intended solely for use by the purchasers of theequipment described in this manual.Sony Corporation expressly prohibits the duplication ofany portion of this manual or the use thereof for anypurpose other than the operation or maintenance of theequipment described in this manual without the expresswritten permission of Sony Corporation.

Le matériel contenu dans ce manuel consiste eninformations qui sont la propriété de Sony Corporation etsont destinées exclusivement à l’usage des acquéreursde l’équipement décrit dans ce manuel.Sony Corporation interdit formellement la copie dequelque partie que ce soit de ce manuel ou son emploipour tout autre but que des opérations ou entretiens del’équipement à moins d’une permission écrite de SonyCorporation.

Das in dieser Anleitung enthaltene Material besteht ausInformationen, die Eigentum der Sony Corporation sind,und ausschließlich zum Gebrauch durch den Käufer derin dieser Anleitung beschriebenen Ausrüstung bestimmtsind.Die Sony Corporation untersagt ausdrücklich dieVervielfältigung jeglicher Teile dieser Anleitung oder denGebrauch derselben für irgendeinen anderen Zweck alsdie Bedienung oder Wartung der in dieser Anleitungbeschriebenen Ausrüstung ohne ausdrücklicheschriftliche Erlaubnis der Sony Corporation.

Printed in Japan

Sony Corporation 2002. 3 08

B&P Company ©2002

BKP-7311 (SY) J, E

3-619-325-01