yd1008 arm and wall plate installation instruction
TRANSCRIPT
W
H
Arm and Wall Plate
01 x1 02 x1
Monitor Plate Extenders
03 x4
Step 3-1 Select monitor plate configuration Step 3-2 Assemble monitor plate and extenders
Select the configuration A , B , C, or D to use based on the measurement from step 2.If your TV hole pattern is greater than 100x100mm, attach extenders [03] to monitor plate [02]using Nut [C] and Bolt [D] .
for VESA hole pattern:75x75mm, 100x100mm.
A
VESA Pattern(WxH)
Configuration VESA Pattern
(WxH) Configuration
75mm x 75mm A C100mm x 100mm A D
B C100mm x 200mm
150mm x 150mm200mm x 100mm200mm x 200mm
C D
M-B
M-A
Use the shorter screws
M-BM-C
M-ENot for M8 screws
M-BM-A
Use the longer screws
M-B
M-E
M-FM-D
Step 3-3 Attach the brackets
(a) For Flat Back
(b) For Round Back / Extra Space
75mm100mm
75m
m10
0mm
200mm20
0mm
150m
m
150mm
200mm
200mm
100m
m
100mm
02B
D
C03
Top of TV
Top of TV
ST6.3 x 60mmLag Bolts
x2 x1 B C DA
Open-end wrench Nuts Bolts
x4 x4
03
02
Max:200x200mm /8x8"Min:75x75mm /3x3"
14"~40"
(V4)
YD1008 INSTALLATION INSTRUCTION
Bubble level X1
Hardware Included
Hardware (Wall /Product)
Philips ScrewsM6 x 15mmM6 x 30mm
Philips ScrewsM4 x 12mmM4 x 30mm
WashersØ6mmM4-5-6
Spacers L10mm
x4x4 x4x4
Philips Screws M8 x 25mm
x4 x4 x4
Spacers L5mm
x4
TV Screws / Washers
M-A M-B M-C M-D M-E M-F
Measure and note the width and the height of the square or rectangle formed from the VESA holes pattern .
Step 2 Mesure your TV pattern
2M2M
Step 1-1 Select TV screw diameter
Thread screws by hand into the threaded holes on the back of your TV to select which screw diameter fits your TV.
M6M4 M8
Correct CorrectToo LongToo Short
Step 1-2 Select TV screw length
75mm ≈ 3in.100mm ≈ 4in.150mm ≈ 6in.200mm ≈ 8in.
for VESA hole pattern:150x150mm, 200x200mm
for VESA hole pattern:100x200mm
for VESA hole pattern:200x100mm
B DC
Max:
(20KG)44LBS
Safety Caution
Must Check Before Getting Started
Installation Tools (Not Included)
BandTape
2M
SocketWrench
ScrewdriverPencil ElectrodrillStud
FinderHammerAwl Wood
Drill BitMasonryDrill Bit
Wood Stud Installation Concrete Installation
1/2"(13mm)3/8"
(10mm)5/32"
(4mm)
MAX:200mm/8"
MAX:200mm/8"
Min. 8"(203mm)
Solid concrete wall
CAUTION: DO NOT install into drywall alone.
<16mm(5/8")
Drywall with wood studs
Max:
(20KG)44LBS
No!
No!
When attaching brackets to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes.
If you have any questions, please contact us.
Please read this instruction carefully before installation.If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.
● This product is designed for use in wood stud and solid concrete wall. - DO NOT install into drywall alone.● The wall must be capable of supporting five times the weight of the TV and mount combined.● Do not apply this product to any purpose not indicated by ELIVED.● Incorrect installation may result in product damage or body injury. ELIVED shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage, please contact us.
21
543
Step 4A Wall plate installation (wood stud)
4A-1
4A-2
Locate your studs. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge-to-edge stud finder.
Position the wall plate at your desired height and line up the holes with your stud center line. Level the wall plate and mark the pilot hole locations x2.
01
4A-3
Lift and hang TV assembly onto arm and wall plate.
Secure the monitor plate to the arm and wall plate with the removed screws and washers from the previous step.
Tilting angle adjustment (+3° / -10°)
Leveling adjustment
Loosen the screws Tighten the screwsTilt the TV
+3 /-10°
Loosen the screw Tighten the screwLevel the TV
Adjust TV to your desired angle then fasten tilting screws with open-end wrench.
If needed, TV can be leveled via adjusting the screw with the open-end wrench or screwdriver.
Adjustments
B
B B
B B
Switch screen horizontally and vertically
If needed, the TV can be rotated ±90 degrees for switching screen between horizontally and vertically.
Use the open-end wrench to loosen and tighten this screw if necessary.Screwdriver can be used for adjusting the screw to secure the TV direction if need. No need to adjust this screw if the mount can hold the TV at your desired direction via the default factory setting.
Horizontal screen
±90°
Vertical screen
B
0° up
90° up
Product dimensions:
5-1
5-2
5-3
+3°/-10°
380mm68mm
200mm
100mm
200m
m
115.8mm10
0mm
210mm
143m
m
59mm
164m
m
Drill pilot holes using a 5/32 in. (4 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2 3/4 in (70 mm). Be sure to drill into the center of the stud.
5/32
inØ
4 m
m
4A-4 01 A
A
Install wall plate using lag bolts with Socket Wrench, NO Electrodrill. Tighten the lag bolts until they are pulled firmly against the wall plate .01
01Position the wall plate at your desired height , level the wall plate and mark the pilot hole locations x2.
4B-1
A
B
Step 4B Wall plate installation (concrete or brick)
Step 5 Lift and hang TV with brackets onto wall bracket
Contact us to have these additional pieces shipped directly to you.
Concrete wall anchor 2pcs (NOT INCLUDED)
Ø10*61mm
01
A
A
A
01
01
Install wall plate using lag bolts and anchors (not included) with Socket Wrench, NO Electrodrill. Tighten the lag bolts until they are pulled firmly against the wall plate . Tighten the lag bolts until they are pulled firmly against the wall plate .
01 Level 01
01
A
4B-2
Drill pilot holes
2.75in (70 mm)
Ø 1
0 m
m
Ø 10 mm
3/8i
n
01
Remove 2 preassembled screws and washers before hang TV on to the wall bracket, and save them for using to next step.
Loosen
Tighten
B
UP
UP 2
2
Level
4B-3
No!
No!
2.75in (70 mm)
180°180°
76 8
11109