tms 114 uf and tms 114t uf technical manual r manual/c3tmsuf_061918.pdfdescriptiontest...

www.pittcometals.com

ARCHITECTURAL METALS, INC.

TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF AND TMS 114T UFTECHNICAL MANUAL

AutoCAD SHX Text

R



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

BLANK PAGE

AutoCAD SHX Text

R

FOR SPECIFIC PRODUCT APPLICATIONS PLEASE CONTACT YOUR PITTCO REPRESENTATIVE

FEATURES

APPLICATIONS

· TMS 114 UF (non-thermal) and 114T UF (thermal barrier) are front setflush glazed systems that are 4 1/2" deep with a 2" wide sightline

· Front face of glass is 3/4" from face of system· Glaze from the outside or inside· Screw spline or shear block fabrication· Glazing options up to 1-1/8" thick· Available in anodized and standard or custom painted finishes· Readily available from stock

· Storefront, Punched Openings, or Ribbon Windows· Single span· Integrated entrance framing to allow Pittco standard entrances

or other speciality entrances to be incorporated

SYSTEM PERFORMANCE (TMS 114 UF Non-Thermal)Description Test Method Allowed Achieved Test Report

Structural ASTM E 330 25 psf 22-03Air ASTM E 283 0.06 cfm/ft2 @ 6.24 psf 0.05 cfm/ft2 @ 6.24 psfWater (Static) ASTM E 331

AAMA 501.1None @ 5 psfNone @ 5 psf

None @ 10 psfNone @ 10 psf

N/A

SYSTEM PERFORMANCE (TMS 114T UF Thermal)Description Test Method Allowed Achieved Test Report

Structural ASTM E 330 25 psfAir ASTM E 283 0.06 cfm/ft2 @ 6.24 psf 0.05 cfm/ft2 @ 6.24 psf

ASTM E 331AAMA 501.1



CRFU Value

N/A

* 1" IGU (1/4-1/2-1/4) Clear Annealed Glass, Air Filled, Aluminum Spacer.** Based on TMS center glazed system

AAMA 1503AAMA 1503

N/AN/A

22-04560.60 22-04

Water (Dynamic)

Water (Static)Water (Dynamic)

22-0322-0322-03

22-0322-0322-0322-03



TMS 114 UF/114T UF

JUNE 2018

FEATURES

1

AutoCAD SHX Text

R



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

BLANK PAGE

2

AutoCAD SHX Text

R

EXPLODED VIEWS PAGE 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4 SIZE DETAILS - TMS 114 UF NON THERMAL PAGES D1 TO D4. . . . . . .

WINDLOAD CHARTS PAGES S1 TO S4. . . . . . . . . . . . . . . . . . . . . . . . . . . . DEADLOAD CHARTS PAGE S5. . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION PROPERTIES PAGE S6. . . . . . . . . . . . . . . . . . . . . . . . . .

1/4 SIZE DETAILS - TMS 114T UF THERMAL BARRIER PAGES D5 TO D8. . ENTRANCE DETAILS PAGE D9. . . . . . . . . . . . . . . . . . . . . . . . . . . .

THERMAL CHARTS PAGES T1 TO T2. . . . . . . . . . . . . . . . . . . . . . . . . .

PRODUCT DESCRIPTION - THERMAL BARRIER PAGES 9 TO 13 . . . . . . . .PRODUCT DESCRIPTION - NON THERMAL PAGES 4 TO 8 . . . . . . . . . . .



TMS 114 UF/114T UF

JUNE 2018

INDEX

3

AutoCAD SHX Text

R

● BASIC USES / RELATED USESFraming is designed for flush glazed, up-front glazed storefront assemblyVertical mullions are typically open back aluminum members, with solid face and flush closure plates forming tubular members for useon single spansHorizontal mullions are of hollow aluminum with removable glazing stopsCorners are configured for 90 degreesGlazing is insulating glass unit or single pane with adaptersGlass may be transparent, opaque, or decorative typesFraming is intended for one story applicationsFramed assembly may be fitted to most rigid and stable framed opening assemblies

● PRODUCT ATTRIBUTES AND CHARACTERISTICSFraming and glazing stops are designed for glass and panelsWind pressure resistance and pressure equalization are standard within the frame assemblyWeep containment, condensate water collection, and drainage to the exterior at concealed weeps are standardIntegral door frames are available

● SELECTION CRITERIAQuality, economy, and good performance are provided at a reasonable costFraming is designed for Interior or exterior environments

● APPLICABLE STANDARDS, RELATED REFERENCESAA (Aluminum Association) - Designation System for Aluminum FinishesAAMA SFM-1-87 - Aluminum Storefront and Entrance ManualAAMA 501.1-05 - Standard Test Method for Water Penetration of Windows, Curtain Walls and Doors using Dynamic PressureAAMA 611-98 - Voluntary Specification for Anodized Architectural AluminumAAMA 1503-98 - Voluntary Test Method for Thermal Transmittance and Condensation Resistance of Windows,Doors, and Glazed Wall SectionsAAMA 2604-05 - Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings onAluminum Extrusions and PanelsAAMA 2605-05 - Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatingson Aluminum Extrusions and PanelsASTM A123/A123M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM B209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and PlateASTM B209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate [Metric]



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

NON-THERMAL PRODUCT DESCRIPTION

4

AutoCAD SHX Text

R

ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and TubeASTM B221M - Standard Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and Tube [Metric]ASTM E283 - Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls and Doors Under SpecifiedPressure Differences Across the SpecimenASTM E330 - Standard Test Method for Structural Performance of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static AirPressure DifferenceASTM E331 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air PressureDifference

● QUALITY, TESTS, CERTIFICATIONS, AND APPROVALSAir Infiltration: Maximum leakage of 0.05 cfm/sq ft. when measured in accordance with ASTM E283 at a test pressure of 6.24 psfStatic Water Leakage: No uncontrolled leakage, when measured in accordance with ASTM E331 at a test pressure difference of 10.0 psfDynamic Water Leakage: No uncontrolled leakage, when measured in accordance with AAMA 501.1 at a test pressure difference of 10.0 psfStructural Performance: Maximum deflection less than 1/175 of the span length and no damage to the assembly, when measured in accordancewith ASTM E330 at a test pressure of 25 psf

● PACKAGING, HANDLING, AND PROTECTION INSTRUCTIONSPackaged in specially designed heavy cartons or shipped pre-fabricated and assembled

● SPECIAL WARRANTYOne (1) year

● LIMITATIONSNot thermally brokenFraming is limited to applications of one story in heightNot intended for continuous members for multiple floor applications

● SAFETY PRECAUTIONSNormal precautions required

● AVAILABILITYFraming is available in all regions of USA - refer to Internet web site for locations and addresses of distributors

● COSTVaries with elevation, configuration and finish desired



TMS 114 UF/114T UF

JUNE 2018

NON-THERMALPRODUCT DESCRIPTION

5

AutoCAD SHX Text

R

PRODUCT PROPERTIES● MATERIAL AND DESIGN

Aluminum: 6063-T6 alloy and temper, to ASTM B221 or ASTM B221MFasteners: Stainless steel, or zinc plated carbon steelPerimeter Anchors: Aluminum, or steel that will be isolated from aluminum componentsGlazing Gaskets: Wedge-type, Ethylene Propylene Diene Monomer (EPDM) rubber with non-stretch cordGlass Stops: Snap-in type

● SHAPE AND DIMENSIONSFrame Size: 2 x 4-1/2 inchGlass Edge Bite: 3/8 inchGlazing Thickness Accepted: 1/8 inch to 1-1/8 inch in increments of 1/16 inch except 7/16 inch, 9/16 inch, 11/16 inch, and 13/16 inch

● SHOP FABRICATION AND ASSEMBLYProvide for flush glazing on all sides with no projecting stopsConfigurations:■ Two-piece snap together mullions■ Solid tubular mullions, assembled to specially designed shear block clipsAccessories:■ Expansion Mullions■ Corner Mullions■ Open Back Perimeter Members■ Integral Door Frames■ Flashing, Subsills■ Head Receptor■ Heavy Duty Mullions■ Standard Steel Reinforcing

● COLORS AND TEXTURES■ Architectural anodic coating, in accordance with AAMA 611;

o Aluminum Association Designation.□ AA-M10C22A31 - Class II - (Pittco #42 Clear)□ AA-M10C22A41 - Class I - (Pittco #43 Clear)□ AA-M10C22A44 - Class I - (Pittco #59 Champagne)□ AA-M10C22A44 - Class I - (Pittco #60 Light Bronze)□ AA-M10C22A44 - Class I - (Pittco #61 Medium Bronze)□ AA-M10C22A44 - Class I - (Pittco #62 Dark Bronze)□ AA-M10C22A44 - Class I - (Pittco #63 Black)



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018


6

AutoCAD SHX Text

R

■ Architectural organic coating, in accordance with AAMA 2604 (50% Kynar 500®);o Finish of Exposed Aluminum shall be compliant with the performance standards set forth in AAMA Specification 2604, High Performance

Organic Coatings on Aluminumo Type: Factory Applied, High Performance, 50% Polyvinylidene Fluoride (PVDF) Coating formulated by a licensed paint manufacturer, and

applied by Paint Manufacturer's Warranty-Approved Applicatoro Pretreatment: Applicator to pre-treat the aluminum with solutions to remove organic and inorganic surface soils, remove residual oxides,

followed by a Chrome Phosphate or Chromate Coating to ensure adhesion to the aluminumo Specify color code, e.g. UC 40577(Duranar Black)

■ Architectural organic coating, in accordance with AAMA 2605 (70% Kynar 500®);o Finish of Exposed Aluminum shall be compliant with the performance standards set forth in AAMA Specification 2605, Superior Performing

Organic Coatings on Aluminumo Type: Factory Applied, High Performance, 70% Polyvinylidene Fluoride (PVDF) Coating formulated by a licensed paint manufacturer, and

applied by Paint Manufacturer's Warranty-Approved Applicatoro Pretreatment: Applicator to pre-treat the aluminum with solutions to remove organic and inorganic surface soils, remove residual oxides,

followed by a Chrome Phosphate or Chromate Coating to ensure adhesion to the aluminumo Specify color code, e.g. UC 40577(Duranar Black)

PRODUCT PLACEMENT● PREPARATION WORK

Ensure openings are of proper size, and are plumb, square, level and in the proper location and alignment

● INSTALLATIONAlign installed assembly plumb and level, free of warp or twistMaintain dimensional tolerances, aligning with adjacent workSeal joints between framing and building structure watertightFollow guidelines in Pittco Fabrication, Sealant and Erection Brochure

● START-UP AND OPERATIONNot Applicable

● OWNER'S MAINTENANCE INSTRUCTIONSWash surfaces with warm water and mild soap; wipe clean, at least once a year



TMS 114 UF/114T UF

JUNE 2018


7

AutoCAD SHX Text

R

Corporate IdentificationPittco Architectural Metals, Inc

1530 Landmeier RoadElk Grove Village, Illinois 60007Tel: (847) 593-3131Fax: (847) 593-9946Toll-Free: (800) 992-7488Internet: http://www.pittcometals.comE-mail: [email protected]

Technical Services AvailableToll-Free: (800) 992-7488

Classification and FilingMasterFormat

Subset of Section 08410 - Metal Framed StorefrontsUniFormat

Section B2030 - (exterior entrance frames) or C1020 (interior entrance frames)



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018


8

AutoCAD SHX Text

R

● BASIC USES / RELATED USESFraming is designed for flush glazed, up-front glazed storefront assemblyVertical mullions are typically open back aluminum members, with solid face and flush closure side plates forming tubular members for use onsingle spansHorizontal mullions are of hollow aluminum with removable glazing stopsGlazing is insulating glass unit or single pane with adaptersCorners are available for 90 degreesGlass may be transparent, opaque, or decorative typesFraming is intended for one story applicationsFramed assembly may be fitted to most rigid and stable framed opening assemblies

● PRODUCT ATTRIBUTES AND CHARACTERISTICSAluminum frame members are thermally improvedFraming and glazing stops are designed for glass and panelsWind pressure resistance and pressure equalization are standard within the frame assemblyWeep containment, condensate water collection, and drainage to the exterior at concealed weeps are standardIntegral door frames are available

● SELECTION CRITERIAQuality, economy, and good performance are provided at a reasonable costFraming is designed for Interior or exterior environments

● APPLICABLE STANDARDS, RELATED REFERENCESAA (Aluminum Association) - Designation System for Aluminum FinishesAAMA SFM-1-87 - Aluminum Storefront and Entrance ManualAAMA 501.1-05 - Standard Test Method for Water Penetration of Windows, Curtain Walls and Doors using Dynamic PressureAAMA 611-98 - Voluntary Specification for Anodized Architectural AluminumAAMA 1503-98 - Voluntary Test Method for Thermal Transmittance and Condensation Resistance of Windows, Doors, and Glazed Wall SectionsAAMA 2604-05 - Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on AluminumExtrusions and PanelsAAMA 2605-05 - Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings onAluminum Extrusions and PanelsASTM A123/A123M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM B209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and PlateASTM B209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate [Metric]ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and TubeASTM B221M - Standard Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and Tube [Metric]



TMS 114 UF/114T UF

JUNE 2018


9

AutoCAD SHX Text

R

ASTM E283 - Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls and Doors Under SpecifiedPressure Differences Across the SpecimenASTM E330 - Standard Test Method for Structural Performance of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static AirPressure DifferenceASTM E331 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air PressureDifference

● QUALITY, TESTS, CERTIFICATIONS, AND APPROVALS

Air Infiltration: Maximum leakage of 0.05 cfm/sq ft. when measured in accordance with ASTM E283 at a test pressure of 6.24 psfStatic Water Leakage: No uncontrolled leakage, when measured in accordance with ASTM E331 at a test pressure difference of 10.0 psfDynamic Water Leakage: No uncontrolled leakage, when measured in accordance with AAMA 501.1 at a test pressure difference of 10.0 psfStructural Performance: Maximum deflection less than 1/175 of the span length and no damage to the assembly, when measured in accordancewith ASTM E330 at a test pressure of 25 psfCondensation Resistance Factor (CRF): 56 when measured in accordance with AAMA 1503 with clear 1” insulated glass unit (1/4, 1/2, 1/4)Insulation U-Factor: 0.60 BTU/hr/sq ft/degrees F when measured in accordance with AAMA 1503 with clear 1” insulated glass unit (1/4, 1/2,1/4)

● PACKAGING, HANDLING, AND PROTECTION INSTRUCTIONSPackaged in specially designed heavy cartons or shipped pre-fabricated and assembled

● SPECIAL WARRANTYOne (1) year

● LIMITATIONSFraming is limited to applications of one story in heightNot intended for continuous members for multiple floor applications

● SAFETY PRECAUTIONSNormal precautions required

● AVAILABILITYFraming is available in all regions of USA - refer to Internet web site for locations and addresses of distributors

● COSTVaries with elevation, configuration and finish desired



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

THERMAL PRODUCT DESCRIPTION

10

AutoCAD SHX Text

R

PRODUCT PROPERTIES● MATERIAL, COMPOSITION AND DESIGN

Aluminum: 6063-T6 alloy and temper, to ASTM B221 or ASTM B221MFasteners: Stainless steel, or zinc plated carbon steelPerimeter Anchors: Aluminum, or steel that will be isolated from aluminum componentsGlazing Gaskets: Wedge-type, Ethylene Propylene Diene Monomer (EPDM) rubber with non-stretch cordGlass Stops: Snap-in typeThermal Barrier: Poured and Debridged Polyurethane and Thermal Slots

● SHAPE AND DIMENSIONSFrame Size: 2 x 4-1/2 inchGlass Edge Bite: 3/8 inchGlazing Thickness Accepted: 1/8 inch to 1-1/8 inch in increments of 1/16 inch except 7/16 inch, 9/16 inch, 11/16 inch, and 13/16 inch

● SHOP FABRICATION AND ASSEMBLYProvide for flush glazing on all sides with no projecting stopsConfigurations:■ Two-piece snap together mullions■ Solid tubular mullions, assembled to specially designed shear block clipsAccessories:■ Expansion Mullions■ Corner Mullions■ Open Back Perimeter Members■ Integral Door Frames■ Flashing, Subsills■ Head Receptor■ Heavy Duty Mullions■ Standard Steel Reinforcing

● COLORS AND TEXTURES■ Architectural anodic coating, in accordance with AAMA 611;

o Aluminum Association Designation.□ AA-M10C22A31 - Class II - (Pittco #42 Clear)□ AA-M10C22A41 - Class I - (Pittco #43 Clear)□ AA-M10C22A44 - Class I - (Pittco #59 Champagne)□ AA-M10C22A44 - Class I - (Pittco #60 Light Bronze)□ AA-M10C22A44 - Class I - (Pittco #61 Medium Bronze)□ AA-M10C22A44 - Class I - (Pittco #62 Dark Bronze)□ AA-M10C22A44 - Class I - (Pittco #63 Black)



TMS 114 UF/114T UF

JUNE 2018

THERMALPRODUCT DESCRIPTION

11

AutoCAD SHX Text

R

■ Architectural organic coating, in accordance with AAMA 2605 (70% Kynar 500®);o Finish on exposed aluminum shall be compliant with the performance standards set forth in AAMA 2605, “Superior Performing Organic

Coatings on Aluminum”.o Type: Factory Applied - High Performance, 70% Polyvinylidene Fluoride (PVDF) coating based on Elf Atochem, Inc. Kynar 500® or

Ausimount USA, Inc. Hylar 5000® resin, formulated by a Licensed Paint Manufacturer and applied by the Paint Manufacturer's WarrantyApproved Applicator.

o Pre-treatment: Applicator to pre-treat the aluminum with solutions to remove Organic and Inorganic Surface Soils and Residual Oxides,followed by a Chrome Phosphate Conversion Coating, at a minimum 40 mg/sq ft to ensure adhesion of paint to aluminum.

o Specify color code, e.g. UC 40577(Duranar Black)

■ Architectural organic coating, in accordance with AAMA 2605 (70% Kynar 500®);o Finish on exposed aluminum shall be compliant with the performance standards set forth in AAMA 2604, “High Performance Organic

Coatings on Aluminum”.o Type: Factory Applied - High Performance, 50% Polyvinylidene Fluoride (PVDF) coating based on Elf Atochem, Inc. Kynar 500® or

Ausimount USA, Inc. Hylar 5000® resin, formulated by a Licensed Paint Manufacturer and applied by the Paint Manufacturer's WarrantyApproved Applicator.

o Pre-treatment: Applicator to pre-treat the aluminum with solutions to remove Organic and Inorganic Surface Soils and Residual Oxides,followed by a Chrome Phosphate Conversion Coating, at a minimum 40 mg/sq ft to ensure adhesion of paint to aluminum.

o Specify color code, e.g. UC 40577(Duranar Black)

PRODUCT PLACEMENT● PREPARATION WORK

Ensure openings are of proper size, and are plumb, square, level and in the proper location and alignment

● INSTALLATIONAlign installed assembly plumb and level, free of warp or twistMaintain dimensional tolerances, aligning with adjacent workSeal joints between framing and building structure watertightFollow guidelines in Pittco Fabrication, Sealant and Erection Brochure

● START-UP AND OPERATIONNot Applicable

● OWNER'S MAINTENANCE INSTRUCTIONSWash surfaces with warm water and mild soap; wipe clean, at least once a year



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

THERMAL PRODUCT DESCRIPTION

12

AutoCAD SHX Text

R

Corporate IdentificationPittco Architectural Metals, Inc

1530 Landmeier RoadElk Grove Village, Illinois 60007Tel: (847) 593-3131Fax: (847) 593-9946Toll-Free: (800) 992-7488Internet: http://www.pittcometals.comE-mail: [email protected]

Technical Services AvailableToll-Free: (800) 992-7488

Classification and FilingMasterFormat

Subset of Section 08410 - Metal Framed StorefrontsUniFormat

Section B2030 - (exterior entrance frames) or C1020 (interior entrance frames)



TMS 114 UF/114T UF

JUNE 2018

THERMALPRODUCT DESCRIPTION

13

AutoCAD SHX Text

R

HEAD

HORIZONTAL

GLASS STOP

SILL

GLASS STOP

OPEN BACK MULLION

SNAP-IN FILLER

SCREW SPLINE ASSEMBLY

SHEAR BLOCK ASSEMBLY

HEAD

HORIZONTAL

GLASS STOP

SILL

GLASS STOP

OPEN BACK MULLIONSNAP-IN FILLER

THE SCREW SPLINE SYSTEM ALLOWS A FRAME TO BE INSTALLED FROM UNITIZED ASSEMBLIES. SCREWS ARE DRIVENTHROUGH THE BACK OF THE VERTICALS INTO SPLINES EXTRUDED IN THE HORIZONTAL FRAMING MEMBERS. INDIVIDUALUNITS ARE THEN SNAPPED TOGETHER TO FORM A COMPLETE FRAME

THE SHEAR BLOCK METHOD OF FABRICATION IS AN ALTERNATE METHOD OF FABRICATION. HORIZONTALSARE ATTACHED TO THE VERTICAL MULLIONS WITH SHEAR BLOCKS. THIS METHOD MUST BE USED WITHTUBULAR VERTICAL MULLIONS.

SHEAR BLOCK

SHEAR BLOCK

SHEAR BLOCK



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

EXPLODED VIEW

14

AutoCAD SHX Text

R

3

4

5

1 2

SCREW SPLINE SHEAR BLOCK

2"T

YP

ICA

L

412"

TYPICAL

2"T

YP

ICA

L

412"

TYPICAL

2VERTICAL

1JAMB

3HEAD

4HORIZONTAL

5SILL

2VERTICAL

1JAMB

3HEAD

4HORIZONTAL

5SILL

42-028 (JAMB)20-168 (PERIMETER FILLER)

42-035 (MULLION)42-029 (GLAZING FILLER)



42-028 (HEAD)20-168 (PERIMETER FILLER)

42-039 (HORIZONTAL)41-031 (GLASS STOP)

42-030 (SILL)41-031 (GLASS STOP)20-168 (PERIMETER FILLER)20-000 (SUB-SILL)

42-028 (HEAD)20-168 (PERIMETER FILLER)41-034 (SHEAR BLOCK)

42-039 (HORIZONTAL)41-031 (GLASS STOP)41-040 (SHEAR BLOCK)

42-030 (SILL)41-031 (GLASS STOP)20-168 (PERIMETER FILLER)20-000 (SUB-SILL)41-034 (SHEAR BLOCK)

2"TYPICAL

41 2"

TY

PIC

AL

2"TYPICAL

41 2"

TY

PIC

AL



TMS 114 UF/114T UF

JUNE 2018

NON-THERMALTYPICAL FRAMING DETAILS (Outside Glazed)

D1DETAILS

AutoCAD SHX Text

R

3

4

5

1 2


2"T

YP

ICA

L

412"

TYPICAL

42-060 (HEAD)41-050 (GLASS STOP)20-168 (PERIMETER FILLER)


42-028 (SILL)20-168 (PERIMETER FILLER)20-000 (SUB-SILL)

2VERTICAL

1JAMB

2VERTICAL

1JAMB





2"TYPICAL

41 2"

TY

PIC

AL

2"TYPICAL

41 2"

TY

PIC

AL

2"T

YP

ICA

L

412"

TYPICAL

42-060 (HEAD)41-050 (GLASS STOP)20-168 (PERIMETER FILLER)41-041 (SHEAR BLOCK)


42-028 (SILL)20-168 (PERIMETER FILLER)41-034 (SHEAR BLOCK)20-000 (SUB-SILL)

3HEAD

4HORIZONTAL

5SILL

3HEAD

4HORIZONTAL

5SILL



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

NON-THERMAL TYPICAL FRAMING DETAILS (Inside Glazed)

D2DETAILS

AutoCAD SHX Text

41-034

AutoCAD SHX Text

R

412"

41 2"

16-705 19-047

2 PIECE NO POCKET CORNER 90° OUTSIDE CORNER

90° INSIDE CORNER ADJUSTABLE MULLION

19-047 42-048

42-049

42-044

42-043

42-14042-141

412" x 41

2" TUBE



TMS 114 UF/114T UF

JUNE 2018

NON-THERMALCORNER DETAILS

D3DETAILS

AutoCAD SHX Text

R

19-168

214"

19-102 20-101

19-152

30-105

17-021

30-18430-184

STANDARD MULLION w/OPTIONAL STEEL

EXPANSION MULLION

14" SNAP IN

GLAZING ADAPTER

12" SNAP IN

GLAZING ADAPTER

FULL LENGTHFLAT FILLER

SNAP INPOCKET FILLER

HEAD RECEPTOR OPTIONAL SILL FLASHINGS

NARROW SIDELITE BASE

16-500

42-028

42-029 42-033

42-032

19-04519-183

17-349

16-142

42-139

42-029

HEAVY WALL MULLION

214"

HEAVY WALLEXPANSION MULLION

42-033

42-025



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

NON-THERMAL MISCELLANEOUS DETAILS

D4DETAILS

AutoCAD SHX Text

12-908-6350

AutoCAD SHX Text

12-908-6350

AutoCAD SHX Text

12-908-6350

AutoCAD SHX Text

R

3

4

5

1 2


2VERTICAL

1JAMB

3HEAD

4HORIZONTAL

5SILL

2VERTICAL

1JAMB

3HEAD

4HORIZONTAL

5SILL



2"TYPICAL

41 2"

TY

PIC

AL

2"T

YP

ICA

L

412"

TYPICAL

41-028 (HEAD)20-168 (PERIMETER FILLER)


41-030 (SILL)41-031 (GLASS STOP)20-168 (PERIMETER FILLER)19-000 (SUB-SILL)

2"T

YP

ICA

L

412"

TYPICAL

41-028 (HEAD)20-168 (PERIMETER FILLER)41-034 (SHEAR BLOCK)


41-030 (SILL)41-031 (GLASS STOP)20-168 (PERIMETER FILLER)19-000 (SUB-SILL)41-034 (SHEAR BLOCK)



2"TYPICAL

41 2"

TY

PIC

AL



TMS 114 UF/114T UF

JUNE 2018

THERMALTYPICAL FRAMING DETAILS (Outside Glazed)

D5DETAILS

AutoCAD SHX Text

R

3

4

5

1 2


2VERTICAL

1JAMB

2VERTICAL

1JAMB



2"TYPICAL

41 2"

TY

PIC

AL



2"TYPICAL

41 2"

TY

PIC

AL

3HEAD

4HORIZONTAL

5SILL

3HEAD

4HORIZONTAL

5SILL

2"T

YP

ICA

L

412"

TYPICAL



41-028 (SILL)20-168 (PERIMETER FILLER)19-000 (SUB-SILL)

2"T

YP

ICA

L

412"

TYPICAL

41-060 (HEAD)41-050 (GLASS STOP)20-168 (PERIMETER FILLER)41-041(SHEAR BLOCK)


41-028 (SILL)20-168 (PERIMETER FILLER)19-000 (SUB-SILL)41-034 (SHEAR BLOCK)



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

THERMAL TYPICAL FRAMING DETAILS (Inside Glazed)

D6DETAILS

AutoCAD SHX Text

41-034

AutoCAD SHX Text

R

19-047

2 PIECE NO POCKET CORNER 90° OUTSIDE CORNER

90° INSIDE CORNER ADJUSTABLE MULLION

19-047 41-048

41-049

41-044

41-043

41-14041-141

412"

41 2"

16-705

412" x 41

2" TUBE



TMS 114 UF/114T UF

JUNE 2018

THERMALCORNER DETAILS

D7DETAILS

AutoCAD SHX Text

R

19-168

214"

19-102 19-101

STANDARD MULLION w/OPTIONAL STEEL

EXPANSION MULLION

14" SNAP IN

GLAZING ADAPTER

12" SNAP IN

GLAZING ADAPTER

FULL LENGTHFLAT FILLER

SNAP INPOCKET FILLER

HEAD RECEPTOR

16-500

41-028

41-029 41-033

41-032

19-04519-183

17-349

19-152

OPTIONAL SILL FLASHINGS

NARROW SIDELITE BASE

16-142

30-105

17-021

30-18430-184

41-139

41-029

HEAVY WALL MULLION

214"

HEAVY WALLEXPANSION MULLION

41-033

41-025



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

THERMAL MISCELLANEOUS DETAILS

D8DETAILS

AutoCAD SHX Text

R

2"T

YP

ICA

L

412"

TYPICAL1

TRANSOM HEAD

2DOOR HEAD

3BOTTOMRAIL


41-036 (TRANSOM HEAD)41-037 (SHEAR BLOCK)

SINGLE ACTING

1

2

3

76

54

10

3

98

DOUBLE ACTING

SINGLE ACTINGDOOR JAMBS

DOUBLE ACTINGDOOR JAMBS

41 2"

TY

PIC

AL

10SINGLE ACTING

HEADER

10DOUBLE ACTING

HEADER

641-036 OR 41-177

(MULLION)

TRANSOM JAMBSTransom area for both double or single acting doors withglass surround. Jambs above transom bar are routed outto accept glass holding insert.


841-177 (MULLION)

941-177 (MULLION)

441-036 (MULLION)

541-036 (MULLION)

741-036 OR 41-177

(MULLION)





TMS 114 UF/114T UF

JUNE 2018

ENTRANCE DETAILS

D9DETAILS

AutoCAD SHX Text

14-090

AutoCAD SHX Text

70-881

AutoCAD SHX Text

R



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

BLANK PAGE

D10

AutoCAD SHX Text

R

SYSTEM ANALYSIS CRITERIA:

DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"

CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"

L/175 FOR SPANS LESS THAN 13'-6"

LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)

SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION

ALUMINUM: 6063-T6

(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)

42-03542-029

A = 15 PSF (720Pa)B = 20 PSF (960 Pa)C = 25 PSF (1200 Pa)D = 30 PSF (1440 Pa)E = 40 PSF (1920 Pa)

42-03542-029

WITH 16-500 STEEL

VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUMSECTIONS.

A

B

CD

E

A

B

C

D

E



TMS 114 UF/114T UF

JUNE 2018

NON-THERMALWINDLOAD CHARTS

S1

AutoCAD SHX Text

R







ALUMINUM: 6063-T6


42-03242-033


42-13942-029

A

B

CD

E



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

NON-THERMAL WINDLOAD CHARTS

S2

AutoCAD SHX Text

R







ALUMINUM: 6063-T6


41-03541-029

41-03541-029

WITH 16-500 STEEL


VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUMSECTIONS.

A

B

CDE

A

B

CD

E



TMS 114 UF/114T UF

JUNE 2018

THERMALWINDLOAD CHARTS

S3

AutoCAD SHX Text

R







ALUMINUM: 6063-T6


A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK

41-03241-033

A

BC

D

E


41-13941-029

A

BCD

E



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

THERMAL WINDLOAD CHARTS

S4

AutoCAD SHX Text

R



ALUMINUM: 6063-T6

A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THE THERMAL BREAK THERMAL SECTIONS

HORIZONTAL OR DEADLOAD LIMITATIONS ARE BASED UPON 1/8" MAXIMUM ALLOWABLE DEFLECTION WITH 1" THICK INSULATED GLASS

A = SETTING BLOCKS AT 1/8 POINTSB = SETTING BLOCKS AT 1/4 POINTS





A

B

A

B

AB AB



TMS 114 UF/114T UF

JUNE 2018

THERMALDEADLOAD CHARTS

S5

AutoCAD SHX Text

R

STRUCTURAL PROPERTIES of TMS 114 UF NON-THERMAL FRAMINGPart Number Ix Sx Iy Sy

16-500 (Steel) 1.093 0.547 0.024 0.04216-501 (Steel) 0.649 0.316 0.032 0.076

19-168 0.508 0.243 0.012 0.01542-028 2.798 1.201 0.405 0.31542-029 0.832 0.351 0.033 0.08142-030 2.065 0.833 0.367 0.30342-032 2.443 0.984 0.252 0.21542-033 1.880 0.831 0.126 0.21242-035 2.631 1.112 0.349 0.27342-039 2.362 0.953 0.627 0.57342-060 2.407 0.954 0.182 0.16042-069 2.770 1.162 0.313 0.23642-139 6.681 2.778 0.583 0.48242-140 2.129 0.159 0.845 0.14542-141 1.935 0.073 0.826 0.084

STRUCTURAL PROPERTIES of TMS 114T UF THERMAL BARRIER FRAMINGPart Number Ix Sx Iy Sy

16-500 (Steel) 1.093 0.547 0.024 0.04216-501 (Steel) 0.649 0.316 0.032 0.076

19-168 0.508 0.243 0.012 0.01541-028 2.798 1.201 0.405 0.31541-029 0.832 0.351 0.033 0.08141-030 2.065 0.833 0.367 0.30341-032 2.443 0.984 0.252 0.21541-033 1.880 0.831 0.126 0.21241-035 2.631 1.112 0.349 0.27341-039 2.362 0.953 0.627 0.57341-060 2.407 0.954 0.182 0.16041-069 2.770 1.162 0.313 0.23641-139 6.681 2.778 0.583 0.48241-140 2.129 0.159 0.845 0.14541-141 1.935 0.073 0.826 0.084



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

SECTION PROPERTIES

S6

AutoCAD SHX Text

R



TMS 114 UF/114T UF

JUNE 2018

THERMAL CHARTS

T1FOR INSTRUCTIONS ON HOW TO READ THERMAL CHARTS PLEASE SEE GENERAL SECTION OF THE CATALOG

AutoCAD SHX Text

R



TMS 114 UF/114T UF

JUNE 2018

TMS 114 UF/114T UF

JUNE 2018

THERMAL CHARTS

T2FOR INSTRUCTIONS ON HOW TO READ THERMAL CHARTS PLEASE SEE GENERAL SECTION OF THE CATALOG

AutoCAD SHX Text

R

tms 114 uf and tms 114t uf technical manual r manual/c3tmsuf_061918.pdfdescriptiontest...

Documents