ordering guide fist-gps2 - ukrcomline.com.ua · ordering guide of the tray patching ... this...

FIST-GPS2 (& FIST-GPST-12) Ordering guide PM Luc Devooght

of 24 Issue 2.2 02-2003

Ordering Guide of the Tray Patching & Splicing Shelf (FIST-GPS2)

This document provides assistance with the selection of shelves for use in FIST cable termination applications. It includes the following sections: 1 Product description 2

2 Ordering information 3

2.1 FIST-GPS2 shelf 3 2.2 FIST-GPST-12 trays 4 2.3 Accessories 5

2.3.1 Accessories for the 125 mm high version 5 2.3.2 Accessories for the 88 mm high version 5 2.3.3 Accessories for the 44 mm high version 5 2.3.4 Ribbon cable termination accessories 5

2.4 Tools & miscellaneous 6

3 Product guide 7

3.1 Shelf description 7 3.1.1 Chassis versions 7 3.1.2 Tray layout 9 3.1.3 Connector adapter with retainer (and pigtail if pre-fibered) 15 3.1.4 Number of trays and content 16

3.2 Shelf capacity 17 3.3 Shelf dimensions 17 3.4 Tray description 17

3.4.1 Tray capacity 17 3.4.2 Tray configuration 17

3.5 Accessories 18 3.5.1 Accessories for the 125 mm high version 18 3.5.2 Accessories for the 88 mm high version 19 3.5.3 Accessories for the 44 mm high version 20 3.5.4 Ribbon cable termination accessories 21

3.6 Tools & miscellaneous 22


of 24 Issue 2.2 02-2003

1 Product description

The generic tray patching & splicing shelf FIST-GPS2 is the mechanical assembly for the fiber management system that provides the function of cable splicing and patchcord patching and connecting in a rack environment. This shelf can be used with Tyco racks as well as with other metric (ETSI) or 19” racks. Multiple configurations are possible:

patching 1. between patchcords 2. pre-connectorized break-out cable to patchcords 3. pre-connectorized intrafacility cable to patchcords 4. ribbon pigtail (with micro fan-out to single pigtails) to patchcords

splicing GPS2-3HU.JPG125 MM HIGH VERSION 1. loose tube cable to pigtails

2. non pre-connectorized intrafacility cable to pigtails 3. non pre-connectorized break-out cable to pigtails 4. ribbon fiber (ribbon splice and micro fan-out) 5. and patching these pigtails to patchcords

The Generic Splice/Patch Shelf Trays FIST-GPST-12 are the organizer trays that house the connector adapters (typical for 12 connectors per tray, or 24 small form factor connectors), fibers and patchcords. It allows for Single Element splicing on the tray itself. An optional basket can be installed for integrated jumper overlength storage. Refer to section 3.2 for limitations with respect to patchcord characteristics. Three different chassis types are available:

− 125 mm high version Maximum 6 trays (or 4 trays when the storage option is selected) can be installed

7N3K6471.JPG88 MM HIGH VERSION

− 88 mm high version Maximum 4 trays (or 2 trays when the storage option is selected) can be installed

− 44 mm high version Maximum 2 trays (or 1 tray when the storage option is selected) can be installed

All generic patching shelves consist of a metal chassis with drawer. A bracket is installed at the rear of the drawer on which the trays can be hinged. The connector adapters can be pre-installed in the organizer trays. Pigtails can be pre-installed in the ‘splice unit’ area of the tray (pre-fibered options - see section 2). Positive fiber management of the pigtails is guaranteed by bend controls on the trays and pigtail belts in the shelf.

GPS2-1HU.JPG44 MM HIGH VERSION


of 24 Issue 2.2 02-2003

2 Ordering information

2.1 FIST-GPS2 shelf

Refer to section 3 for full product descriptions.

AA

MANA

PAQA

--

--

--T12A

--U12A

Tray options (Section 3.1.2)

FIST-GPS2-X-XX X-X

NN Without trays

Other options contain GPST-12 trays with following configuration:

Cable type

Patchcord orpre-connectorized BOC

Loose tube cable orIFC (connectorized or not)

Non pre-connectorized BOC

Ribbon pigtail(patching only)

Ribbon fiber(splicing & patching)

Spliceholder ormicro fan-out

-

SMOUV12 (1)ANT

SMOUV12 (1)ANT

SMOUV12 (1)ANT

SMOUV12 (1)ANT

micro fan-out

SMOUV-R2-12 (3) &micro fan-out

Std. Connectors

AA

IAJA

EAFA

KALA

GAHA

R4AR8AR12A

S4AS8AS12A

AA

AIAJ

AEAF

AKAL

AGAH

AR4AR8AR12

AS4AS8AS12

BOC: Break-out cable (diameter of individual pigtails inside the BOC is max. 2.8 mm.)IFC: Intra facility cable(1) Only for SMOUV-1120-02 (45 mm long heat-shrinkable splice protector) which is supplied with the kit.(2) Contact your local sales engineer for shelves with pre-fibered pre-connectorized IFC.(3) Ribbon SMOUV included in the kit.

Chassis type (Section 3.1.1)

Number of trays & content (Section 3.1.4)

Pre-fibered

no

yes (2)

no

yes

no

yesyesyes

yesyesyes

R4R8R12

R4R8R12

MI

Metric19” J 19”J 19” K 19”K 19”

125 mm high 88 mm high 44 mm high

0246

No trays2 trays4 trays6 trays

0246

No trays2 trays4 trays6 trays

RSTU

Storage basket, no trays (chassis type M, I and J only)Storage basket + 1 tray (chassis type K only)Storage basket + 2 trays (chassis type M, I, J only)Storage basket + 4 trays (chassis type M and I only)

RSTU

Storage basket, no trays (chassis type M, I and J only)Storage basket + 1 tray (chassis type K only)Storage basket + 2 trays (chassis type M, I, J only)Storage basket + 4 trays (chassis type M and I only)

Trays only Storage & Trays

AA

AMAN

APAQ

--

--

--AT12

--AU12

Patchcords leave shelf sideLeft Right Left Right

Connector adapter with retainer (and pigtails if pre-fibered) (Section 3.1.3)

SFF Connectors

Notes * E2000 pigtails are with E2000 connectors, centered ferrule tuning method, 0.1 dB insertion loss ** In case of adapters only (not pre-fibered), use S5D, F5D, E5D or T5D)

Connector type SC FC E2000 DIN ST MU LC NoneSingle mode UPC A C K Q U1 L1 N

APC B D F (*)Multimode 50/900µ S5D F5D E5D T5D

62.5/900µ S5E (**) F5E (**) E5E (**) T5E (**)


of 24 Issue 2.2 02-2003

2.2 FIST-GPST-12 trays

FIST-GPST-12 trays are asymmetrical, the patching area is not located in the center of the tray but slightly moved to one side. The patching areas of 2 consecutive trays should not fall on each other but alter. In general, all the patchcords of the trays within one shelf are leaving the shelf at the same side. Therefore trays are supplied per set of 2 complementary pieces. Example

Patchcord unit Splice unit

} set of 2 complementary trays

patching area

} set of 2 complementary trays

tray exitpatch-cords

shelf exitpatchcords

The following combinations are available (Refer to section 3 for more details):

FIST-GPST-12-XX X-2Tray lay-out (Section 3.1.2)Trays are ordered per set of 2 complementary pieces (each set can hold 24 std. connectors or 48 SFF connectors) with the following configuration:

BOC: Break-out cable (diameter of individual pigtails inside the BOC is max. 2.8 mm.)IFC: Intra facility cable(1) Only for SMOUV-1120-02 (45 mm long heat-shrinkable splice protector) which is supplied with the kit.(2) Contact your local sales engineer for shelves with pre-fibered pre-connectorized IFC.(3) Ribbon SMOUV included in the kit.

Connector adapter with retainer (and pigtails if pre-fibered) (Section 3.1.3)

Connector type SC FC E2000 DIN ST MU LC NoneSingle mode UPC A C K Q U1 L1 N

APC B D F (*)Multimode 50/900µ S5D F5D E5D T5D

62.5/900µ S5E (**) F5E (**) E5E (**) T5E (**)

AA

MANA

PAQA

--

--

--T12A

--U12A

Cable type

Patchcord orpre-connectorized BOC

Loose tube cable orIFC (connectorized or not)

Non pre-connectorized BOC

Ribbon pigtail(patching only)

Ribbon fiber(splicing & patching)

Spliceholder ormicro fan-out

-

SMOUV12 (1)ANT

SMOUV12 (1)ANT

SMOUV12 (1)ANT

SMOUV12 (1)ANT

micro fan-out

SMOUV-R2-12 (3) &micro fan-out

Std. Connectors

AA

IAJA

EAFA

KALA

GAHA

R4AR8AR12A

S4AS8AS12A

AA

AIAJ

AEAF

AKAL

AGAH

AR4AR8AR12

AS4AS8AS12

Pre-fibered

no

yes (2)

no

yes

no

yesyesyes

yesyesyes

R4R8R12

R4R8R12

AA

AMAN

APAQ

--

--

--AT12

--AU12

Patchcords leave shelf sideLeft Right Left Right

SFF Connectors

Notes * E2000 pigtails are with E2000 connectors, centered ferrule tuning method, 0.1 dB insertion loss ** In case of adapters only (not pre-fibered), use S5D, F5D, E5D or T5D)


of 24 Issue 2.2 02-2003

2.3 Accessories

2.3.1 Accessories for the 125 mm high version

Name Qty/Pk Description

FIST-CT-S-2 1 pc Side cable termination unit for GPS2 (for max. 2 cables)

FIST-CT-B-2 1 pc Back cable termination unit for GPS2 (for max. 2 cables)

FIST-MB2-M 1 pc ETSI mounting brackets for 19” shelf FIST-MB2-M-AS 1 pc ETSI mounting brackets for 19” shelf (asymmetrical

mounting) FIST-GS-FLEX-17-50-S5027 50 m Flexible tubing, internal ∅ 17 mm FIST-GPS2-ID-10 10 pc Identification cards and card holders



FIST-CT-2HU-S-2 1 pc Side cable termination unit for GPS2 (for max. 2 cables)

FIST-CT-2HU-B-2 1 pc Back cable termination unit for GPS2 (for max. 2 cables)

FIST-MB2-2HU-M 1 pc ETSI mounting bracket for 19” shelf FIST-MB2-2HU-M-AS 1 pc ETSI mounting bracket for 19” shelf (asymmetrical

mounting) FIST-GS-FLEX-12-50 50 m Flexible tubing, internal ∅ 12 mm FIST-GPS2-2HU-ID-10 10 pc Identification cards and card holders



FIST-CT-1HU-B-1 1 pc Back cable termination unit for GPS2 (for 1 cable) FIST-MB2-1HU-M 1 pc ETSI mounting bracket for 19” shelf FIST-GS-FLEX-10-50-S5027 50 m Flexible tubing, internal ∅ 10 mm FIST-GPS2-1HU-ID-10 10 pc Identification cards and card holders

2.3.4 Ribbon cable termination accessories


FIST-GR-CTB100 1 pc Cable termination kit for max. 2 loose tube/ribbon cables FIST-GR-CTB100-CC 1 pc Cable termination kit for max. 2 central core cables

(single fiber or ribbon) FIST-GR-TD-5MM 1 pc Tube divider 6 in–6 out (for GR) FIST-GPS2-TD-5MM 1 pc Tube divider 6 in–6 out (for GPS2 chassis types) FIST-TUBE-5MM-30 30 m 5 mm tubing


of 24 Issue 2.2 02-2003

2.4 Tools & miscellaneous


FIST-GTU2 18 pc Group termination units FISTV-E7187-6316 25 m Velcro roll FACC-CAGE-NUT-TOOL 1 pc Cage nut installation tool FACC-ALLEN-KEY-5-350 1 pc Allen key, diameter 5 mm, length 350 mm for back

mounting of shelf in rack


of 24 Issue 2.2 02-2003

3 Product guide

3.1 Shelf description

3.1.1 Chassis versions

125 mm high version

Two chassis versions are available: metric and 19” width. They both are painted like the cover. The shelf has field-mountable brackets to accommodate for:

− front mounting of the shelf − mounting with brackets 240 mm from the back of the shelf − mounting specifically for Raychem’s FIST racks − back mounting

For ease of access to the connectors, the drawer can be pulled out and held in position with a releasable spring. The drawer is equipped with the bracket necessary for mounting the trays and Velcro to secure them. It contains a metal hingeable cover with one central latch. Cards are provided at the inside of the cover for a clear identification. Cable attachment: In general cables are attached either to brackets on specific locations inside the rack (see ordering guides FIST-WR, FIST-GR2) or to the side or back of the shelf. Kits for side or back attachment to shelves should be ordered separately (see section 3.5). Other elements are fitted according to the options selected. Identification cards (2) and two card holders are provided at the back side of the front cover. (Cards will be visible when the cover is open). 88 mm high version

One chassis version is available: 19”. However mounting between ETSI mounting profiles (like for example in the FIST-GR2 or -WR) is possible using the adaptation brackets. The shelf has field-mountable brackets to accommodate for:

− front mounting of the shelf − mounting with brackets 240 mm from the back of the shelf − mounting specifically for Raychem’s FIST racks (in combination with the 19”-ETSI

adaptation brackets - to be ordered separately) − back mounting

For ease of access to the connectors, the drawer can be pulled out and held in position with a releasable spring. The drawer is equipped with the bracket necessary for mounting the trays and Velcro to secure them. The metal front cover is part of the drawer and contains 2 screws to close the drawer. Cable attachment: In general cables are attached either to brackets on specific locations inside the rack (see ordering guides FIST-WR, FIST-GR2) or to the side or back of the shelf. Kits for side or back attachment to shelves should be ordered separately (see section 3.5). Other elements are fitted according to the options selected. Identification cards (2) and two card holders are provided on the front side of the drawer.


of 24 Issue 2.2 02-2003

44 mm high version

One chassis version is available: 19”. However mounting between ETSI mounting profiles is possible using the adaptation brackets. The shelf has field-mountable brackets to accommodate for:

− front mounting of the shelf − mounting with brackets 240 mm from the back of the shelf − mounting specifically for Raychem’s FIST racks (in combination with the 19”-ETSI

adaptation brackets - to be ordered separately) − back mounting

The drawer is equipped with the bracket necessary for mounting the trays. The metal front cover is part of the drawer. Cable attachment: In general cables are attached either to brackets on specific locations inside the rack (see ordering guides FIST-WR, FIST-GR2) or to the side or back of the shelf. Kits for back attachment to shelves should be ordered separately (see section 3.5). An identification label is provided on the front side of the drawer.


of 24 Issue 2.2 02-2003

3.1.2 Tray layout

FIST-GPS2 can be ordered: − without trays, option NN should be selected in that case. − with trays including connector adapters with retainers – and with pigtails if a pre-

fibered tray layout is selected (see following paragraphs). The tray has a modular design: it consists of a base plate, on which 2 units can be clicked. The tray layout parameter will differ depending on the type of units installed and on which side the patchcords will leave the shelf. patchcord unit splice unit patching area

FGPS2002.JPG

Example: Note that patchcords which enter the shelf at the RIGHT side, are routed to the patchcord unit located at the LEFT side of the tray.

Acable attachment plate

Type AI

splice holder

I

GPS2-015.JPG

In case the patchcords would enter the shelf from the left side; the pigtail unit (A) has to be at the right and the splice unit (I) at the left; this setup would require a type IA. The splice unit will get a different parameter depending on the splice holder type and whether the unit has to be pre-fibered or not. The different tray layout options are described in the following paragraphs.


of 24 Issue 2.2 02-2003

Patching between patchcords

GPS2

In this layout, two identical patch units are installed on the baseplate. This layout could also be used for patching pre-connectorized break-out cable. Tray layout: AA

Splicing & patching loose tube cable to pigtails

GPS2-013.JPG

.7N3K4422

The loose tube is terminated on the tray and the fibers are spliced to the secondary coated pigtails coming from the patchpanel. The pigtail which is spliced in the splice unit should be 0.58 to 1.5 m long (and can be respliced 0 up to 6 times, depending on its length). We recommend a pigtail length of 1 meter, which allows 5 resplices. ∗ Pre-fibered trays contain the selected adapters with retainers and the pigtails between the

patching area and splice holder. Pigtails are 900 µm, semi-tight and 1.5 m long (for the connector type of the pigtail, see section 3.1.3).

Tray layout

Splice protector Standard connectors SFF connectors (small form factor)

Pre-fibered * SMOUV AI – IA MA – AM ANT AJ – JA NA – AN Not pre-fibered SMOUV AE – EA PA – AP

ANT AF – FA QA – AQ


of 24 Issue 2.2 02-2003

Splicing and patching break-out cable to pigtails

BOC.JPG

GPS2-014.JPG

A break-out cable contains individual 900 µm fibers with kevlar and outer jacket (up to 2.8 mm) and a strength member which are bundled in an outer jacket. A break-out cable can be pre-connectorized or non pre-connectorized. When pre-connectorized, the patch units (AA) have to be used. Three GTU's (group termination units) are used to attach the pigtail kevlar per group of 4 pigtails when the break-out cable is not-pre-connectorized The pigtail which is spliced in the splice unit should be 0.58 to 1.5 m long (and can be respliced 0 up to 6 times, depending on its length). We recommend a pigtail length of 1 meter, which allows 5 resplices.

* Pre-fibered trays contain the selected adapters with retainers and the pigtails between the patching area and splice holder. Pigtails are 900 µm, semi-tight and 1.5 m long (for the connector type of the pigtail, see section 3.1.3).

Tray layout


Pre-fibered * SMOUV AK – KA ANT AL – LA Not pre-fibered SMOUV AG – GA

ANT AH – HA Not applicable

GTU


of 24 Issue 2.2 02-2003

Splicing and patching IFC cable to pigtails

7N3K1584.JPG

GPS2-015.JPG

An IFC is an amount (e.g. 8 or 12) of 900 µm pigtails bundled in an outer jacket with kevlar and can be pre-connectorized or non pre-connectorized. An IFC has the great advantage of giving less congestion than 12 individual pigtails with outer jacket and kevlar. Intrafacility cable is routed on the splice unit, whether it is pre-connectorized or not. In case one connector fails or a fiber breaks, the complete IFC should not be replaced since the splice holder can be used to splice a new pigtail to the broken fiber.

* Pre-fibered trays contain the selected adapters with retainers and the pigtails between the patching area and splice holder. Pigtails are 900 µm, semi-tight and 1.5 m long (for the connector type of the pigtail, see section 3.1.3).

Tray layout


Pre-fibered * SMOUV AI – IA MA – AM

ANT AJ – JA NA – AN

Not pre-fibered SMOUV AE – EA PA – AP ANT AF – FA QA – AQ


of 24 Issue 2.2 02-2003

Patching Ribbon pigtails

Micro fan-out

Single fiber pigtails

Ribbon pigtail

GPS2

Patchcord

Micro fan-out


Ribbon pigtail

GPS2

Patchcord

GPS2-016.JPG

Ribbonized fibers are primary coated fibers placed next to each other in one plane. An acrylate coating or polyester tape keeps the fibers together. Most common are 4-, 8- and 12-fiber ribbon cable. * The ribbon pigtail (part up to the micro fan-out) is 5 m long.

The single fiber pigtails are 900 µm and semi-tight, for the connector type of the pigtail, see section 3.1.3. A connector adapter with retainer should always be selected in the case of ribbon pigtail.

Tray layout

Ribbon type

# fan-outs per tray Standard connectors

SFF connectors (small form factor)

Std conn.

SFF conn.

Pre-fibered * R4 3 AR4 – R4A

R8 1 AR8 – R8A Contact PM R12 1 2 AR12 – R12A AT12 – T12A Not pre-fibered Not applicable Not applicable


of 24 Issue 2.2 02-2003

Patching & splicing ribbon fiber

Micro fan-out


GPS2

Patchcord

Ribbon fiber

Micro fan-out


GPS2

Patchcord

Ribbon fiber

7N3K1588.JPG

Ribbonized fibers are primary coated fibers placed next to each other in one plane. An acrylate coating or polyester tape keeps the fibers together. Most common are 4-, 8- and 12-fiber ribbon cable. The ribbon of the incoming cable is being spliced to the fan-out. The single fiber pigtails are 900 µm and semi-tight, for the connector type of the pigtail, see section 3.1.3. A connector adapter with retainer should always be selected in the case of ribbon pigtail. Ribbon SMOUVs are included in the kit. A 864 fiber ribbon cable can be terminated as follows:

Single fiber

12 tubes, each containing 6 ribbon 12’s, each going to 1 GPS2 shelf

864 fiber ribbon cable

6 tubes, each con-taining 1 ribbon 12

Tray 1Tray 2

...6

GPS2FIST-GPS2-TD-5MM

FIST-TUBE-5MM-30

FIST-GR-CTB100

GPS2

GPS2

GPS2

RibbonFan-out

Tray layout

Ribbon type

# fan-outs per tray Standard connectors

SFF connectors (small form factor)

Std conn.

SFF conn.

Pre-fibered * R4 3 AS4 – S4A

R8 1 AS8 – S8A Contact PM R12 1 2 AS12 – S12A AU12 – U12A Not pre-fibered Not applicable Not applicable


of 24 Issue 2.2 02-2003

3.1.3 Connector adapter with retainer (and pigtail if pre-fibered)

Un-pre-fibered shelves can be ordered with trays including pre-installed adapters and retainers. Select the appropriate adapter from the name string table page 3, or N for none. The trays of pre-fibered shelves always include pre-installed adapters with retainers and pigtails. Pigtails are 900 µm, semi-tight and 1.5 m long (ribbon pigtails are shorter). Select the appropriate connector type from the table below:

Single mode connectors Multimode connectors UPC APC 8° UPC

Connector type

50 dB 60 dB 50 dB 60 dB SC A B S5D S5E FC C D F5D F5E E2000 - F (1) E5D E5E DIN K - - - ST Q (2)- - T5D T5E MU U1 - - - LC L1 - - -

(1) Centered ferrule tuning method (2) ST/PC, 45 dB (not 50 dB)


of 24 Issue 2.2 02-2003

3.1.4 Number of trays and content

GPS2-1HU.JPG

The number of trays can be selected. Furthermore, the GPS2 offers the possibility to store a random overlength of jumpers underneath the trays. The storage basket’s height equals 2 trays in the 3HU and 2HU shelf and equals 1 tray in the 1HU shelf. Example of storage in 44 mm high version

Chassis height Options

125 mm 88 mm 44 mm

0

2

4 NA

6 NA NA

R NA

S NA NA

T NA

U NA NA

Legend:

FIST-GPST-12 tray

Storage basket for3HU and 2HU chassis

Storage basket for 1HU chassis


of 24 Issue 2.2 02-2003

3.2 Shelf capacity

Chassis type Capacity M, I J K

# trays per shelf − without storage basket − with storage basket

6 4

4 2

2 1

# connectors per shelf − without storage basket − with storage basket

Std. 72 48

SFF 144 96

Std. 48 24

SFF 96 48

Std. 24 12

SFF 48 24

Compatible tray (set of 2 trays) FIST-GPST-12-XXX-2 # connectors per tray 12 (std. connectors) / 24 (SFF connectors) Splicing capacity 12 or 24 splices when splice unit is used Jumper length inside shelf 0.9 m Limitations with respect to patchcord characteristics The shelf for standard connectors is designed for patchcords with ∅ 2.4 mm. The shelf for SFF connectors is designed for patchcords with ∅ 1.7 mm and the length of the connector inclusive boot shall be max. 40 mm for the pigtails located at the splicing side of the tray. Contact the product manager for applications not covered by this document. 3.3 Shelf dimensions

Chassis type Dimensions in mm M I J K

Width (with/without mounting brackets) 531 / 494 481 / 444 481 / 444 481 - 444

Height HU - Height units

125 5 metric HU

125 3 19” HU

88 2 19” HU

44 1 19” HU

Depth 280 280 280 280

Note: A HU is a “height unit”. Refer to rack documentation for more details. 3.4 Tray description

3.4.1 Tray capacity

Tray FIST-GPST-12-XXX-2 # connectors per tray 12 or 24 Splicing capacity 12 or 24 splices when splice unit is used 3.4.2 Tray configuration

Please refer to the tray layouts in section 3.1.2.


of 24 Issue 2.2 02-2003

3.5 Accessories


DSC00055.JPG

Cable termination side FIST-CT-S-2 Cable termination unit - side, to terminate max. 2 cables at the side of the shelf. This kit contains: − bracket − flextube − 1 flextube clamp − 2 strength member fixation devices − mounting screws − tie-wraps

DSC00007.JPG

Cable termination back FIST-CT-B-2 Cable termination unit - back, to terminate max. 2 cables at the back of the shelf. This kit contains: − bracket − flextube − 1 flextube clamp − 2 strength member fixation devices − mounting screws − tie wraps

7N3K4322.JPG

ETSI mounting brackets for 19” shelf FIST-MB2-M ETSI mounting brackets to mount a 19” shelf (125 mm high) between ETSI mounting profiles.

7N3K4323.JPG

Asymmetrical ETSI mounting brackets for 19” shelf FIST-MB2-M-AS ETSI mounting brackets to mount a 19” shelf (125 mm high) asymmetrically between ETSI mounting profiles (to gain space at one side of the shelf). A modified trumpet is provided in the kit in case a trumpet has to be mounted at the ‘narrow’ side.

RA11.JPG

Flexible tubing FIST-GS-FLEX-17-50-S5027 50 m of flextube (internal ∅ 17 mm) to route and group tubes from a cable attachment plate to the shelves when no side or back termination plate is used.


of 24 Issue 2.2 02-2003

7N3K5401.JPG

Identification cards and card holders FIST-GPS2-ID-10 10 identification cards and card holders. For detailed layout, see Addendum 1.


DSC00002.JPG

Cable termination side FIST-CT-2HU-S-2 Cable termination unit - side, to terminate max. 2 cables at the side of the shelf. This kit contains: − bracket − flextube − 1 flextube clamp − 2 strength member fixation devices − mounting screws − tie-wraps

DSC00005.JPG

Cable termination back FIST-CT-2HU-B-2 Cable termination unit - back, to terminate max. 2 cables at the back of the shelf. This kit contains: − bracket − flextube − 1 flextube clamp − 2 strength member fixation devices − mounting screws − tie wraps

DCP03891.JPG

ETSI mounting brackets for 19” (88 mm) shelf FIST-MB2-2HU-M ETSI mounting bracket to mount a 19” shelf between ETSI mounting profiles.

Asymmetrical ETSI mounting brackets for 19” (88 mm) shelf FIST-MB2-2HU-M-AS ETSI mounting brackets to mount a 19” shelf (88 mm high) asymmetrically between ETSI mounting profiles (to gain space at one side of the shelf).


of 24 Issue 2.2 02-2003

RA11.JPG

Flexible tubing FIST-GS-FLEX-12-50 50 m of flextube (internal ∅ 12 mm) to route and group tubes from a cable attachment plate to the shelves when no side or back termination plate is used.

7N3K6461.JPG

Identification cards and card holders FIST-GPS2-2HU-ID-10 10 identification cards and card holders. For detailed layout, see Addendum 2.


DSC00006.JPG

Cable termination back FIST-CT-1HU-B-1 Cable termination unit - back, to terminate 1 cable at the back of the shelf. This kit contains: − flextube − 1 strength member fixation device − tie wraps

ETSI mounting brackets for 19” (44 mm) shelf FIST-MB2-1HU-M ETSI mounting bracket to mount a 19” shelf between ETSI mounting profiles.

RA11.JPG

Flexible tubing FIST-GS-FLEX-10-50-S5027 50 m of flextube (internal ∅ 10 mm) to route and group tubes from a cable attachment plate to the shelves when no side or back termination plate is used.

7N3K6460.JPG

Identification cards and card holders FIST-GPS2-1HU-ID-10 10 identification cards. For detailed layout, see Addendum 3.


of 24 Issue 2.2 02-2003

3.5.4 Ribbon cable termination accessories

GCO2OG14.JPG

Ribbon loose tube cable termination kit FIST-GR-CTB100 Cable termination kit for max. 2 ribbon loose tube cable. Can be mounted next to the shelf. Up to 6 tubes of R12. Strength member fixation compatible with most types of strength members (1.5-5 mm Ø).

GCO2OG15.JPG

Central core cable termination kit FIST-GR-CTB100CC Cable termination kit for max. 2 central core cables. Can be mounted next to the shelf. Strength member fixation (till 2.5 mm Ø).

7N3K1585.JPG

Tube divider to mount in rack side duct FIST-GR-TD-5MM Tube divider to be placed in the side duct of a rack. 5 tubes 5mm in – 5 tubes 5 mm out can be used to spread (ribbon) fibers over several tubes.

7N3K1586.JPG

Tube divider to mount in shelf FIST-GPS2-TD-5MM Tube divider to be placed behind the hinge of a GPS2 shelf. Typical application: 1 tube in (6 R12) 6 tubes out (each 1 R12). A bend control on the cover protects the jumpers leaving the shelf. Can be placed in GPS2 chassis types M, I (3 HU) and J (2 HU) only.

I&C003.JPG

5 mm tubing FIST-TUBE-5MM-30 30 m of 5 mm tubing to route ribbon fibers between the tube dividers and the trays.


of 24 Issue 2.2 02-2003

3.6 Tools & miscellaneous

DSC00099.JPG

Group termination unit FIST-GTU2 This kit contains 18 group termination units. In case not pre-connectorized break-out cable has to be spliced to pigtails, a GTU is used to attach the pigtail kevlar per group of 4 pigtails at the entrance of the splicing area of the tray.

FRWR044.JPG

Velcro roll FISTV-E7187-6316 Velcro to segment or secure pigtails. Supplied on a roll 25 m long (width 25 mm) to be cut to length as required.

TO04.JPG

Allen key FACC-ALLEN-KEY-5-350 Allen key, diameter 5 mm, length 350 mm for back-mounting of shelves in rack.

TO23.JPG

Cage nut tool FACC-CAGE-NUT-TOOL Tool to install cage nuts in the rack.


of 24 Issue 2.2 02-2003

Addendum 1: identification card layout for the 125 mm high shelf


of 24 Issue 2.2 02-2003



Tyco Electronics Raychem NV Telecom Outside Plant Diestsesteenweg 692 B-3010 Kessel-Lo, Belgium www.tycoelectronics.com

All of this information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics makes no warranties as to the accuracy or completeness of the information and disclaims any liability regarding its use. Tyco Electronics’ only obligations are those in the Standard Terms and Conditions of Sale for this product and in no case will Tyco Electronics be liable for any incidental, indirect or consequential damages arising from the sale, resale, use or misuse of the product. Tyco Electronics Specifications are subject to change without notice. In addition, Tyco Electronics reserves the right to make changes in materials or processing, without notification to the Buyer, which do not affect compliance with any applicable specification. Tyco and FIST are trademarks.

Copyright Tyco Electronics 1999

ordering guide fist-gps2 - ukrcomline.com.ua · ordering guide of the tray patching ... this...

Documents