ordering guide fist-cab2 · 2016-11-20 · fist-cab2 ordering guide pm luc devooght page 3 of 13...

FIST-CAB2 Ordering guide PM Luc Devooght

of 13 Issue 1.5 02-2003

Ordering Guide of the Fiber-Optic Street Cabinet (FIST-CAB2)

This document provides assistance with the selection of street cabinets for use in FIST cable termination applications. It includes the following sections: 1 Product description 2

2 Ordering information 3

2.1 FIST cabinet 3 2.2 FIST cabinet accessories kit 3

2.2.1 Separate items of the cabinet accessories kit 4 2.3 Other FIST-CAB2 accessories 4

2.3.1 Cable seal kits 4 2.3.2 Cabinet installation 5 2.3.3 Cabinet connection kits 5 2.3.4 Shelves & trays 5

2.4 Tools 5

3 Product guide 6

3.1 Cabinet description 6 3.2 Cabinet characteristics 7 3.3 FIST-CAB2 accessories kit 8

3.3.1 Flexclip mounting plate 8 3.3.2 Vertical pigtail management 9 3.3.3 Cable inlet plates 10

3.4 Other FIST-CAB2 accessories 11 3.4.1 Cable seal kits 11 3.4.2 Cabinet installation 11 3.4.3 Cabinet connection kits 12


of 13 Issue 1.5 02-2003

1 Product description

The FIST Street Cabinet, FIST-CAB2, is an all-purpose metal outdoor cabinet designed to accommodate the FIST generic shelf family (ETSI and 19”). It offers dust-proof, environmental and mechanical protection for the fiber management functions of splicing, patching and passive component integration. FIST-CAB2 is designed for outdoor applications and needs to be placed on a pedestal (Refer to the Application Guide for pedestal dimensions and main dimensions of the cabinet). The FIST-CAB2 can be fitted with FIST shelves (max. 7 shelves) and allows the storage of: − 672 primary coated fiber splices in single circuit management − 1344 primary coated fiber splices in single element management − 288 fiber terminations to cable pigtails with interconnect patching facility − 504 fiber terminations to cable pigtails with cross connect patching facility The FIST-CAB2 has provision for the installation of 7 FIST units, for example, 3 FIST-GSS2 (FIST Generic Splicing Shelf), 3 FIST-GPS2 (FIST Generic Patch Shelf), and 1 FIST-POM (Pigtail Orientation Module). We advise you to use the Application Guide to work out the required configuration before ordering the cabinet.


of 13 Issue 1.5 02-2003

2 Ordering information

NOTE: When ordering a FIST-CAB2, it is important to always select the required accessories kit FIST-CAB2-A-X-XXXX (see section 2.2 and 3.3) and the necessary cable seal kits (see section 2.3.1 and 3.4.1). Refer to sections 3.1 and 3.3 for detailed product description and pictures. 2.1 FIST cabinet

Standard cabinet kit content FIST-CAB2-XX

01 Stand alone cabinet

− aluminum dual wall housing − 2 front doors with swing handle and 3 point actuated locking system − half cylinder lock with 2 keys − 2 ETSI mounting profiles, including the drum plates − 4 blank cable inlet plates (see section 3.3.1) − 4 eyebolts to unload cabinet from truck − 4 metal screw plugs to close the eyebolt holes after installation − 1 flexclip mounting plate (see section 3.3.1) − 1 set of loose tube storage holder 2.2 FIST cabinet accessories kit

When ordering a FIST outdoor cabinet, it is important to define the cabinet accessories kit. This accessories kit always contains the following standard components: − 7 attachment clips for flexible tube fixation (see section 3.3.1) − 1 installation instruction (showing how to terminate cables, install the GSS2 splicing & GPS2

patching shelves, etc.) The accessories kit allows the selection of the optional components: − Specific cable inlet plates for different cable diameters − The vertical pigtail management drums Each component can also be ordered separately (see Section 2.2.1). Refer to Section 3.3 for a complete product description and pictures. The following FIST CABINET ACCESSORIES KITS are available:

Cable inlet plate with oval portseal and termination kit

0, 1 or 2 pieces

FIST-CAB2-A-X-X X X X

Cable inlet plate with 2 round holesand plugs for cable Ø 15-26 mm

0, 1, 2, 3 or 4 pieces


0, 1, 2, 3 or 4 pieces


0, 1, 2, 3 or 4 pieces

N NoneA 6 drums for interconnect or

cross-connect configuration

Vertical pigtail management


of 13 Issue 1.5 02-2003

2.2.1 Separate items of the cabinet accessories kit

Although it is recommended that you initially order a cabinet together with a selected accessories kit and cable seal kits, the components of the accessories kit can also be ordered separately.

Name Qty/Pk Description

FIST-CAB2-FMP-01 1 pc Flexclip mounting plate, including 1 pack of 7 attachment clips for flex tube fixation (see FIST-FLEXCLIP-17-02)

FIST-FLEXCLIP-17-02 7 pcs Attachment clip for flexible tubing FIST-FLEXCLIP-17-03 7 pcs Add-on clips for flexible tubing (to be mounted onto the

FIST-FLEXCLIP-17-02) FIST-GS-FLEX-17-50-S5027 50 m Flexible tubing (ID 17 mm) FIST-CAB2-DRM-6 1 pc Kit of 6 drums to mount on the drum plate to create a

vertical pigtail management unit for interconnection or cross connection configuration (see section 3.3.1 or application guide for more details)

FIST-CAB2-CIP6-01 1 pc Cable inlet plate with 6 holes, 6 plugs and cable attachment fixation for 6 cables



FIST-CAB2-OSK-LTS01 1 pc Cable inlet plate with 1 oval hole, 1 oval port seal kit with cable termination hardware for 2 cables

FISTV-TW-NN-188 100 pc TIE-WRAP 188 mm long (not re-openable) FISTV-E7187-6313 25 m Velcro roll

2.3 Other FIST-CAB2 accessories

These accessories are ordered in addition to the FIST-CAB2 and the FIST-CAB2-A-Kit to suit different applications. Refer to Section 3.4 for a complete product description and pictures. 2.3.1 Cable seal kits


FIST-CAB2-RSK-LTS-01 1 pc Round seal kit for single fiber loose tube cable (dia. 6-14 mm), including a PG16 seal and cable termination hardware for 1 cable




of 13 Issue 1.5 02-2003

2.3.2 Cabinet installation

The cabinet needs to be placed on a pedestal (in plastic or constructed in concrete or bricks).


FIST-CAB2-SOKL-300 1 pc Glass fiber reinforced plastic pedestal for the street cabinet, 300 mm high



2.3.3 Cabinet connection kits

Two or more cabinets can be connected side-to-side or back-to-back using the following kits:


FIST-CAB2-SCK 1 kit Side connection kit for cabinet FIST-CAB2-BCK 1 kit Back connection kit for cabinet FIST-CAB2-AFK 1 kit Anchor frame to be mounted on and anchored in a

concrete pedestal FIST-CAB2-PCK 1 kit Pedestal connection kit to connect 900 or 1200 mm high

pedestals (side-to-side or back-to-back) 2.3.4 Shelves & trays

Select the required shelves (and trays) from the corresponding ordering guides:

Function Ordering guide

Splicing Shelf FIST-GSS2 Patching Shelf and Trays FIST-GPS2/GPST-12 Splicing and Patching Shelf FIST-GMS2 Splicing and Patching Shelf and Tray FIST-GPS2/GPST-12

All shelves can be used but FIST-GSS2 and FIST-GPS2 are recommended for higher density. 2.4 Tools

In addition to all the standard installation tools required to install FIST products, the following tools are needed for the installation of the FIST cabinet: Allen key M5, screw drivers (x and -) and:


FACC-ALLEN-KEY-5-350 1 pc Allen key, diameter 5 mm, length 350 mm for back-mounting of shelves in the cabinet and to mount the drums onto the drum plate


of 13 Issue 1.5 02-2003

3 Product guide

3.1 Cabinet description

The FIST-CAB2 double-wall cabinet consists of:

7N3K2629A.JPG

An aluminum construction containing: Two side- and one rear double-wall detachable panel, which are perforated at the bottom for natural airflow from bottom to top (air outlet via the roof). In case of extreme solar radiation, the natural convection of the air results in a good heat dissipation. It also controls the water condensation inside the cabinet.

7N3K2713.JPG

A double wall roof construction, with 4 eyebolts preinstalled. After delivery and installation on the premises, these eyebolts can be removed and the threaded holes can be closed with metal screws (M10x16 included with the cabinet).

7N3K2630.JPG

Two double wall front doors, left and right hinged, with a swing handle, a half cylinder lock (EURO DIN) with 3-point-latch system and a door stop. A document holder is mounted on the inside of the left door. All other small parts (screw, nuts, washers, etc.) are made from stainless steel type 316.

7N3K2636.JPG

A sealed aluminum bottom plate with 4 cut-outs for cable inlet plates (2 left and 2 right - see section 3.3.1 for different cable inlet plates). The 4 cut-outs are sealed with blank plates.


of 13 Issue 1.5 02-2003

7N3K2630A.JPG

2 Stainless steel ETSI mounting profiles, including the drum plates (for interconnection or cross-connection purposes) with integrated extrusion profiles with 41 holes for cage nuts M6 are mounted at the backside of the inner frame and allows the installation of the FIST splicing or patching shelves.

7N3K2643.JPG

Two earthing provisions (M8) are available on the frame, near the door hinge.

7N3K2644.JPG

In addition, 1 horizontal mounting plate for flexible tube fixations (max. 14 flexible tubes) is pre-installed on the right side of the cabinet. This mounting plate can also be relocated on the left side of the cabinet (10 extra T-nuts are supplied with the cabinet).

3.2 Cabinet characteristics

Property Part Characteristic(s)

Dimensions Overall (WxHxD) (including roof) 1220 x 1230 x 425 mm Inner frame (WxHxD) 1128 x 1160 x 328 mm Useful depth 280 mm Vertical ETSI mounting profiles (H) 35 ETSI HU useful

(41 ETSI HU total) Weight Empty cabinet approx. 80 kg Material Frame and double wall panels

Screws & nuts Aluminum alloy Stainless steel 316

Finish Outer frame Chromatized and textured powder coated light gray (RAL 7035), especially for outdoor use.

Locking mechanism Swing handle with half cylinder lock (EURO DIN) and 3-point-latch system

Remark: A pedestal is required upon which the cabinet is placed. Refer to the application guide for more information.


of 13 Issue 1.5 02-2003

3.3 FIST-CAB2 accessories kit

3.3.1 Flexclip mounting plate

7N3K2721.JPG

Flexclip mounting plate FIST-CAB2-FMP-01 An additional plate to mount flexclips for max. 14 flextubes can be selected. (1 plate is already included in the basic FIST-CAB2). This kit contains also 1 pack with 7 attachment clips (FIST-FLEXCLIP-17-02) for mounting the flexible tubing, required to route the fibers to the splicing shelves (FIST-GSS2).

7N3K2722.JPG

Attachment clip for flextube FIST-FLEXCLIP-17-02 The loose tubes of the FO cable are routed to different splicing shelves using flextubes to protect the fibers. These flextubes are hold by flexclips on the flexclip mounting plate.

7N3K2723..JPG

Add-on clips for flextube FIST-FLEXCLIP-17-03 When more than 7 flextubes are required, add-on clips (to be mounted onto the FIST-FLEXCLIP-17-02) can be used.

RA11.JPG

Flextube FIST-GS-FLEX-17-50-S5027 Flexible tubing to route and protect the loose tubes from the cable termination to the splicing shelves. Roll of 50 m.


of 13 Issue 1.5 02-2003

3.3.2 Vertical pigtail management

7N3K2830.JPG

Pigtail management drums FIST-CAB2-DRM-6 This kit of 6 drums with mounting screws, allows to create the vertical pigtail management function inside the cabinet for interconnect configuration or cross connection configuration.

Interconnection: 3 drums are installed on the left side and 3 drums are installed on the right side of the shelves.

Cross connection: 6 drums are installed on the left side of the shelves (see application guide for more details)


of 13 Issue 1.5 02-2003

3.3.3 Cable inlet plates

The FIST-CAB has a bottom cover with 4 cut-outs (2 on the left and 2 on the right side). Depending on the type and quantity of cables used, different cable inlet plates can be selected:

7N3K2725.JPG

FIST-CAB2-CIP6-01 Cable inlet plate with 6 holes, 6 plugs and cable attachment fixation for 6 cables. Cable diameter range 6 – 14 mm

7N3K2726.JPG

FIST-CAB2-CIP4-01 Cable inlet plate with 4 holes, 4 plugs and cable attachment fixation for 4 cables. Cable diameter range 9 – 18 mm

7N3K2727.JPG

FIST-CAB2-CIP2-01 Cable inlet plate with 2 holes, 2 plugs and cable attachment fixation for 4 cables. Cable diameter range 15 -26 mm

7N3K2732B.JPG

FIST-CAB2-OSK-LTS01 Cable inlet plate with 1 oval hole and 1 oval port seal kit with cable termination hardware for 2 cables.


of 13 Issue 1.5 02-2003

3.4 Other FIST-CAB2 accessories

3.4.1 Cable seal kits

7N3K2904.JPG

FIST-CAB2-RSK-LTS-01 Round seal kit for single fiber loose tube cable (dia. 6-14 mm), including a PG16 seal and cable termination hardware for 1 cable.

7N3K2905.JPG


7N3K2906.JPG


3.4.2 Cabinet installation

7N3K2720.JPG

FIST-CAB2-SOKL-300 Glass fiber reinforced plastic pedestal, upon which the cabinet can be placed. This 300 mm high pedestal is typically used when a concrete base is constructed on the premises.

7N3K2719.JPG

FIST-CAB2-SOKL-900 Glass fiber reinforced plastic pedestal, upon which the cabinet can be placed. This 900 mm high pedestal is typically used when no concrete base is available. About 600 mm of the pedestal is buried. The above-ground part has a removable front cover for access to the cable overlength space. A U-shaped profile is available for cable fixation with tie-wraps.


of 13 Issue 1.5 02-2003

7N3K2718.JPG

FIST-CAB2-SOKL-1200 Glass fiber reinforced plastic pedestal, upon which the cabinet can be placed. This 1200 mm high pedestal is typically used when no concrete base is available, and the ground conditions are unstable. About 900 mm of the pedestal is buried. The above-ground part has a removable front cover for access to the cable overlength space. A U-shaped profile is available for cable fixation with tie-wraps.

3.4.3 Cabinet connection kits

7N3K4326.JPG

Side connection kit FIST-CAB2-SCK This kit should be used if two cabinets are connected side-to-side in order to maintain an IP55 sealing rating. The kit includes the frame to put in between the cabinets, mounting bolts, nuts, washers and distance brackets to put in between the anchor frames if anchor frame kits (FIST-CAB2-AFK) are used.

7N3K5477.JPG

Back connection kit FIST-CAB2-BCK This kit should be used if two cabinets are connected back-to-back in order to maintain an IP55 sealing rating. The kit includes the frame to put in between the cabinets, mounting bolts, nuts, washers and distance brackets to put in between the anchor frames if anchor frame kits (FIST-CAB2-AFK) are used.

7N3K4327.JPG

Anchor frame kit FIST-CAB2-AFK An anchor frame is used on the casted concrete pedestal and includes anchor hooks that should be imbedded in the wet mortar. If cabinets are connected side-to-side or back-to-back, they need to be outlined perfectly to maintain their sealing rate. This will be obtained by using distance brackets between their anchor frames.


of 13 Issue 1.5 02-2003

7N3K4318.JPG

Pedestal connection kit FIST-CAB2-PCK Distance brackets to easily connect two pedestals (FIST-CAB2-SOKL-900 or -1200) side-to-side or back-to-back.

Tyco Electronics Raychem NV Telecom Outside Plant Diestsesteenweg 692 B-3010 Kessel-Lo, Belgium www.tycoelectronics.com

All of this information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics makes no warranties as to the accuracy or completeness of the information and disclaims any liability regarding its use. Tyco Electronics’ only obligations are those in the Standard Terms and Conditions of Sale for this product and in no case will Tyco Electronics be liable for any incidental, indirect or consequential damages arising from the sale, resale, use or misuse of the product. Tyco Electronics Specifications are subject to change without notice. In addition, Tyco Electronics reserves the right to make changes in materials or processing, without notification to the Buyer, which do not affect compliance with any applicable specification. Tyco and FIST are trademarks.

Copyright Tyco Electronics 2001

ordering guide fist-cab2 · 2016-11-20 · fist-cab2 ordering guide pm luc devooght page 3 of 13...

Documents