2005-2007 kawasaki 1600 nomad - power commander · i220-411 2005-2007 kawasaki vn1600n - pciii usb...
TRANSCRIPT
![Page 1: 2005-2007 Kawasaki 1600 Nomad - Power Commander · i220-411 2005-2007 Kawasaki VN1600N - PCIII USB - 1 2005-2007 Kawasaki 1600 Nomad Installation Instructions Dynojet Research 2191](https://reader031.vdocuments.site/reader031/viewer/2022022012/5b1663097f8b9a4a6d8ba85e/html5/thumbnails/1.jpg)
i220-411 www.powercommander.com 2005-2007 Kawasaki VN1600N - PCIII USB - 1
2005-2007 Kawasaki 1600 NomadInstallation Instructions
Dynojet Research 2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
Parts List1 Power Commander1 USB Cable1 CD-ROM1 Installation Guide1 Power Adapter2 Power Commander Decals2 Dynojet Decals2 Velcro® Strip1 Alcohol Swab
You can also download the PowerCommander software and latest mapsfrom our web site at:
www.powercommander.com
The ignition MUST be turnedOFF before installation!
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Button Adjustment Display
Faceplate Buttons
USB PortExpansion Port
![Page 2: 2005-2007 Kawasaki 1600 Nomad - Power Commander · i220-411 2005-2007 Kawasaki VN1600N - PCIII USB - 1 2005-2007 Kawasaki 1600 Nomad Installation Instructions Dynojet Research 2191](https://reader031.vdocuments.site/reader031/viewer/2022022012/5b1663097f8b9a4a6d8ba85e/html5/thumbnails/2.jpg)
1 Remove the main seat and thepassenger seat.
2 Remove the fuel tank
Note: The installation can be donewithout removing the fuel tankbut it may be easier to have itremoved
3 To remove the fuel line squeezethe sides of the connector (Fig. A). Disconnect the twoelectrical connectors.
4 Loosen the four bolts holding onthe left hand side cover (Fig. B).
5 Route the PCIII harness betweenthe tray and the frame (Fig. C).
Fig.
AFi
g. B
Fig.
C
i220-411 www.powercommander.com 2005-2007 Kawasaki VN1600N - PCIII USB - 2
Disconnect these lines
Loosen these bolts
PCIII harness
![Page 3: 2005-2007 Kawasaki 1600 Nomad - Power Commander · i220-411 2005-2007 Kawasaki VN1600N - PCIII USB - 1 2005-2007 Kawasaki 1600 Nomad Installation Instructions Dynojet Research 2191](https://reader031.vdocuments.site/reader031/viewer/2022022012/5b1663097f8b9a4a6d8ba85e/html5/thumbnails/3.jpg)
6 Continue routing the PCIII har-ness towards the front of thebike. Route underneath theframe and towards the left handside of the rear cylinder(Fig. D).
7 Continue routing the PCIII har-ness along the frame towards thefront of the bike. Locate thestock connector for the throttlebodies (Fig. E).
8 Unplug this connector.
9 Plug the connectors from thePCIII in-line of the stock con-nector (Fig. F).
Fig.
DFi
g. E
Fig
F
i220-411 www.powercommander.com 2005-2007 Kawasaki VN1600N - PCIII USB - 3
Unplug this connector
PCIII harness
Stock connectors
PCIII connectors
![Page 4: 2005-2007 Kawasaki 1600 Nomad - Power Commander · i220-411 2005-2007 Kawasaki VN1600N - PCIII USB - 1 2005-2007 Kawasaki 1600 Nomad Installation Instructions Dynojet Research 2191](https://reader031.vdocuments.site/reader031/viewer/2022022012/5b1663097f8b9a4a6d8ba85e/html5/thumbnails/4.jpg)
10 Attach the ground wire from thePCIII to the negative side of thebattery (Fig G).
11 Install the PCIII under the lefthand side cover (Fig. H).
NOTE:
If you have a California model itis best to velcro the unit to thefront portion of the charcoalcanister (Fig J). Use the sup-plied velcro to attach the unit.
Fig.
GFi
g. H
i220-411 www.powercommander.com 2005-2007 Kawasaki VN1600N - PCIII USB - 4
PCIII ground wire
Fig.
J