through-conduit gate valves - armaturygroup.cz · the gate valves are designed in compliance with...
TRANSCRIPT
THROUGH-CONDUIT GATE VALVES
www.armatur ygroup.czwww.armaturygroup.cz 2
TYPE S33.JTHROUGH-CONDUIT GATE VALVES
ApplicationThrough-conduit gate valves are isolating valves designed for full closing of the working media flow. They can be used for temperatures up to 200°C. If the gate valves are used for regulating or throttling purposes, the manufacturer does not guarantee the tightness. The gate valves are full-bore piggable valves with a flow resistance coefficient equal to that of the piping. Therefore they are suitable especially for long-distance pipeline systems.
Working medium water non-corrosive liquids petroleum and petroleum products gas
The working medium shall not contain any mechanical impurities.
Technical descriptionThe gate valves are designed in compliance with API 6D. Cast-welded design - the gate valve body is made of castings and wrought semi-finished products.
Welded design - the gate valve body is made of wrought semi-finished products.
The body parts and the bonnet are connected by a flanged joint. The slide is entered from the top (TOP ENTRY) and the obturator can be situated in its lower part or its upper part as required by the customer. The design of seats incorporates a primary metal-to-metal sealing and a secondary soft sealing ring in the seat. The design of seats enable to depressurize the valve body cavity (DBB) and to relieve the increased pressure from the body cavity to the piping automatically. The stem is sealed by self-sealing PTFE lip seals or O-rings.
Operation manual bevel gear electric actuator pneumatic actuator bare stem ready for connection of an actuator
The standard connecting dimensions for connection of a manual gear operator or an electric actuator are according to ISO 5210.
Accessories drain valve or plug vent valve or plug by-pass valve sealant injection to seats and stem specific requirements
If accessories are not specified by the customer, the scope of its delivery meets the requirements of API Spec 6D.
Testing Pressure tests are carried out with water in compliance with API Spec 6D or API 598. Special tests as required by the customer.
Connection to the piping welded ends - according to ASME B16.25 flanged ends - according to ASME B16.5, ASME B16.47 (by agreement)
End-to-end dimensions according to API Spec 6D. InstallationThe gate valves shall be installed into horizontal piping in vertical position with the actuator on the top only. Advantages very low flow resistance coefficient special design of seats - guarantee of 100% tightness piggability no danger of entrapment of liquid in the body cavity seating surfaces of the seats in permanent contact with the gate
TOP ENTRY design - possibility of refurbishment without removal from the piping system
stem cover with position indicator
Type ClassNPS
4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 48
Cast-welded300 • • • • • • • • • • • • • • • • • • • • •400 • • • • • • • • • • • • • • • • • • • • •600 • • • • • • • • • • • • • • • • • • • • •
Welded150 • • • • • • • • • • • • • • • • • • • • •300 • • • • • • • • • • • • • • • • • • • • •
Production range
www.armatur ygroup.czwww.armaturygroup.cz 3
TYPE S33.JTHROUGH-CONDUIT GATE VALVES
Material
Position Component Cast-welded design Welded design
1 Body A352 LCC, A350 LF2 A216 WCB, A105 A694 F52, A516 Gr.70
2 Bonnet A694 F52, A516 Gr.70 A94 F52, A516 Gr.70
3 Slide A694 F52 + ENP, A516 Gr.70 + ENP A694 F52 + ENP, A516 Gr.70 + ENP
4 Seat A350 LF2 A516 Gr.70 A350 LF2 A516 Gr.70
5 Stem A276 420 T 17-4 PH A276 420 T 17-4 PH
6 Bonnet bolt A320 L7* A193 B7 A320 L7* A193 B7
7 Bonnet nut A194 7* A194 2H A194 7* A194 2H
8 Stem nut Al-bronze
9 Bonnet gasket Graphite, Viton*
10 Packing PTFE, Viton*
*Equivalent or as required by the customer
Connection: ASME B16.5, ASME B16.47 FLANGED ENDS ASME B16.25 WELDED ENDS
8
5
6, 7
2
10
9
4
1
3
Welded design Cast-welded design
NPS 4 - 48 • Class 150 - 600 • Tmax 200 °CBody design: through-conduit gate valve according to API Spec 6DFull bore
www.armatur ygroup.czwww.armaturygroup.cz 4
THROUGH-CONDUIT GATE VALVES TYPE S33.J
NPS D L WE L RF H1 H2 H (open) kg WE kg RF
4 102 305 305 270 530 905 140 1556 152 403 403 340 640 1100 225 2458 203 419 419 430 840 1390 370 410
10 254 457 457 500 960 1640 530 58512 305 502 502 565 1100 1880 700 77014 337 762 762 630 1170 2010 990 109016 387 838 838 700 1360 2300 1340 148018 438 914 914 770 1460 2540 1700 188020 489 991 991 845 1600 2795 2150 238022 540 1092 1092 980 1800 3120 2700 285024 591 1143 1143 1035 1900 3360 3050 340026 635 1245 1245 1150 2100 3600 3800 420028 686 1346 1346 1200 2200 3840 4500 495030 737 1397 1397 1280 2310 4070 5300 590032 781 1524 1524 1345 2490 4350 6050 670034 832 1626 1626 1410 2640 4590 7050 780036 876 1727 1727 1500 2750 4800 7950 880038 927 - - 1600 2950 5100 9000 1000040 978 1931 1931 1650 3140 5400 9500 1050042 1022 - - 1750 3200 5540 11400 1260048 1168 2286 2286 1950 3600 6300 16500 18200
Class 300
NPS 4 - 48 • Class 300-600 • Tmax 200 °CBody design: through-conduit gate valve according to API Spec 6DCast-welded design
Connection: ASME B16.5, ASME B16.47 FLANGED ENDS ASME B16.25 WELDED ENDS
H(op
en)
H2H1
D
L
www.armatur ygroup.czwww.armaturygroup.cz 5
THROUGH-CONDUIT GATE VALVES TYPE S33.J
NPS D L WE L RF H1 H2 H (open) kg WE kg RF
4 102 406 406 270 530 905 155 1756 152 495 495 340 640 1100 255 2858 203 597 597 430 840 1390 420 460
10 254 673 673 500 960 1640 635 70512 305 762 762 565 1100 1920 815 91014 337 826 826 630 1170 2050 1050 118016 387 902 902 700 1360 2340 1600 178018 438 978 978 800 1460 2600 2050 227520 489 1054 1054 870 1600 2850 2200 245022 540 1143 1143 980 1800 3100 3300 365024 591 1232 1232 1040 1950 3360 3950 445026 635 1308 1308 1150 2100 3650 4800 535028 686 1397 1397 1250 2200 3850 5450 610030 737 1524 1524 1300 2400 4200 6500 725032 781 1651 1651 1360 2500 4350 7600 845034 832 1778 1778 1450 2640 4600 8600 965036 876 1880 1880 1550 2750 4850 9800 1100038 927 - - 1600 2950 5100 11000 1250040 978 2083 2083 1650 3140 5400 13400 1480042 1022 - - 1750 3200 5600 14600 1620048 1168 - - 1950 3600 6300 20400 22700
NPS D L WE L RF H1 H2 H (open) kg WE kg RF
4 102 432 432 280 530 905 270 3006 152 559 559 350 660 1100 320 3908 203 660 660 430 840 1390 530 570
10 254 787 787 510 960 1640 805 89512 305 838 838 580 1120 1920 1150 120014 337 889 889 630 1200 2050 1250 138016 387 991 991 720 1360 2340 2050 226018 438 1092 1092 800 1500 2600 2650 290020 489 1194 1194 870 1660 2850 3350 375022 540 1295 1295 980 1870 3100 4100 460024 591 1397 1397 1060 2000 3360 4350 500026 635 1448 1448 1150 2150 3650 5900 660028 686 1549 1549 1250 2250 3850 6700 750030 737 1651 1651 1320 2400 4200 7800 865032 781 1778 1778 1380 2550 4350 8900 990034 832 1930 1930 1450 2750 4600 10300 1140036 876 2083 2083 1550 2850 4850 11750 1300038 927 - - 1600 3000 5100 13300 1480040 978 - - 1700 3160 5400 15200 1680042 1022 2439 2439 1800 3300 5600 16800 1870048 1168 - - 2000 3750 6300 23900 26500
Class 400
Class 600
NPS 4 - 48 • Class 300-600 • Tmax 200 °CBody design: through-conduit gate valve according to API Spec 6DCast-welded design
Connection: ASME B16.5, ASME B16.47 FLANGED ENDS ASME B16.25 WELDED ENDS
www.armatur ygroup.czwww.armaturygroup.cz 6
THROUGH-CONDUIT GATE VALVES TYPE S33.J
NPS D L WE L RF H1 H2 H (open) kg WE kg RF
4 102 305 229 270 530 905 90 1006 152 403 267 340 640 1100 178 2008 203 419 292 430 840 1390 318 348
10 254 457 330 500 960 1640 445 50512 305 502 356 565 1100 1880 520 57514 337 572 381 630 1170 2010 815 90516 387 610 406 700 1360 2300 910 101018 438 660 432 770 1460 2540 1340 149020 489 711 457 845 1600 2795 1610 179022 540 762 508 980 1800 3120 1990 220524 591 813 508 1035 1900 3360 2320 258026 635 864 559 1150 2100 3600 2680 298028 686 914 610 1200 2200 3840 3140 348030 737 914 660 1280 2310 4070 3590 398032 781 965 711 1345 2490 4350 4120 458034 832 1016 762 1410 2640 4590 4700 520036 876 1016 813 1500 2750 4800 5100 568038 927 - - 1600 2950 5100 5680 630040 978 - 1575 1650 3140 5400 6300 700042 1022 - 1625 1750 3200 5540 6950 770048 1168 - 1803 1950 3600 6300 8900 9900
Class 150
NPS 4 - 48 • Class 150 • Tmax 200 °CBody design: through-conduit gate valve according to API Spec 6DWelded design
Connection: ASME B16.5, ASME B16.47 FLANGED ENDS ASME B16.25 WELDED ENDS
H(op
en)
H2H1
ø D
L
www.armatur ygroup.czwww.armaturygroup.cz 7
THROUGH-CONDUIT GATE VALVES TYPE S33.J
NPS D L WE L RF H1 H2 H (open) kg WE kg RF
4 102 305 305 270 530 905 90 1106 152 403 403 340 640 1100 178 2158 203 419 419 430 840 1390 318 380
10 254 457 457 500 960 1640 500 66012 305 502 502 565 1100 1880 800 91014 337 762 762 630 1170 2010 820 101016 387 838 838 700 1360 2300 1100 136018 438 914 914 770 1550 2640 1650 195020 489 991 991 970 1700 2890 1950 240022 540 1092 1092 980 1900 3220 2400 290024 591 1143 1143 1035 2000 3460 3100 365026 635 1245 1245 1150 2200 3700 3600 405028 686 1346 1346 1200 2300 3940 4100 470030 737 1397 1397 1280 2400 4170 4800 535032 781 1524 1524 1350 2600 4450 6300 695034 832 1626 1626 1410 2750 4700 7000 780036 876 1727 1727 1500 2850 4900 7750 850038 927 - - 1600 3050 5200 9350 1000040 978 - 2083 1700 3250 5500 11000 1170042 1022 - 2134 1800 3300 5700 12000 1280048 1168 - 2286 2000 3700 6400 17500 18600
Class 300
NPS 4 - 48 • Class 300 • Tmax 200 °CBody design: through-conduit gate valve according to API Spec 6DWelded design
Connection: ASME B16.5, ASME B16.47 FLANGED ENDS ASME B16.25 WELDED ENDS
H(op
en)
H2H1
ø D
L
www.armaturygroup.cz
The ARMATURY Group a.s. company reserves the right for changes of technical products-specifications, and is not responsible for incidental misprints.
Issued in February 2016
Czech RepublicARMATURY Group a.s.Production plant and Headquarters Nádražní 129, 747 22 Dolní Benešovtel.: +420/553 680 111fax: +420/553 680 333email: [email protected]
SlovakiaARMATÚRY GROUP, s.r.o.Registered officeJánošíkova 264, 010 01 Žilinatel.: +421/41/707 77 77fax: +421/41/707 77 70email: [email protected]
AustriaArmatury Group GmbHARMATURY Group a.s. official representative for AustriaAttemsgasse 45/1/7, A-1220 Vídeňmob.: +43 (0) 664 /88 51 33 33tel.: +43 (0) 1 / 20 21 985fax: +43 (0) 1 / 20 21 985e-mail: [email protected]
RussiaAO „ARMATURY Group a.s.“3rd street Tverskaya-Yamskaya, house 31/35, 125047 Moskvatel./fax: +7/495 956 3335email: [email protected]
ChinaARMATURY GROUP Co., LtdSubsidiary companyXinjing road 18Zhangjiagang Economic & Technological Development ZoneJiangsu, Chinamob.: (China): +86 137 7326 6078mob.: (CZ): +420 606 713 721e-mail: [email protected]