bunk bed mk 2
TRANSCRIPT
BUSSYBUNK BED MK 2
Version 1.1
www.fantasticfurniture.com.au
PAGE 2www.fantasticfurniture.com.au
Enjoy Your purchase from
Australia’s Best Value Furniture Store
HELPFUL BUNK BED SAFETY TIPSBunk beds should be checked periodically to ensure that the guardrail,ladder and other components are secure and in the correct position and all connectors are tight.
We recommend that children under the age of nine (9) do not use the upper bunk. Children should be discouraged from playing on the bunk bed.
No more than one person should use the upper bunk at any time (unless otherwise stated).
Bunk beds should be placed a minimum of 2 metres away from any ceiling fans to prevent any injury to the upper bunk occupant.
Read through the instructions carefully before you begin.
Assembly checklist
Identify and lay out all of the components before you begin assembly.
Unless instructed, do not fully tighten screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
Make sure you have all the required tools. Never use power tools unless instructed.
Useful Information
PAGE 3www.fantasticfurniture.com.au
through the instructions care sure you have all the requiredy g
y and lay out all of the compo t t d d t f ll ti ht
use power tools unless instr
What you needto assemble the product
Other tools you need
DO NOT USE
18 x Cam BoltsØ5 x 45 mm
(H1)
18 x Cam NutsØ14.5 x 11.9 mm
(H2)
75 x Large BoltsØ6 x 50 mm
(H3)
67 x Barrel NutsØ9.5 x 11 mm
(H4)
4 x Medium BoltsØ6 x 30 mm
(H5)
30 x Small BoltsØ6 x 20 mm
(H6)
P1 x 4
Parts listBox 1:P2,P3,P4,P5,P7,P8,P9,P18,P27,P38,P39,P40,P41,P42Box 2:P10,P32,P34,P36,P37Box 3:P1,P12,P13,P14,P15,P16,P17,P19,P22,P23,P24,P25,P26,P28,P29,P33,P35Box 4:P6,P10,P11,P20,P21,P30,P31
Flat head screwdriverPhillips head screwdriver
www.fantasticfurniture.com.au PAGE 4
112 x Large DowelsØ8 x 30 mm
(H7)
28 x Medium DowelsØ8 x 20 mm
(H8)
2 x Small DowelsØ6 x 30 mm
(H9)
42 x Large ScrewsØ4 x 25 mm
(H10)
4 x Small ScrewsØ4 x 20 mm
(H11)
View Outside
P2
P3
P4 x 4
P5
P5
P6
P7
P8
P9P10
P11 P12P13 x 4P14
P15P16
P17
P18
P19
P20
P21
P22
P23P26
P26
P27
P27
P27P28
P28
P29x 13 P30
P31
P32
P33
P33P10
P34
P35
P36
P36 P36 P36P37
P10
P38
P38
P38P38
P24
P25
P32
P39 x 4
P40P42
P41
P11
4 x Bolts(H12)
P10
www.fantasticfurniture.com.au PAGE 5
QTYSHAPEITEM NO.
CARTON NO.
P2
P3
P4
P5
P7
P8
P9
P18
P27
P38
P39
P40
P41
P42
P10
P32
P34
P36
P37
P1
P12
1
1
4
2
1
1
1
1
5
4
4
1
2
1
2
2
1
4
1
4
1
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
2/4
2/4
2/4
2/4
2/4
3/4
3/4
QTYSHAPEITEM NO.
CARTON NO.
P14
P15
P16
P17
P19
P22
P23
P24
P25
P26
P28
P29
P33
P35
P6
P10
P11
P20
P21
P30
1
1
1
1
1
1
1
1
1
2
2
13
2
5
1
2
1
1
1
1
P13 8 3/4
P31 1
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
Step 1- Unpack cartons,Identify and layout each item below.
PAGE 6
Step 2
www.fantasticfurniture.com.au
- Lay Panels (P2)+(P3) flat as shown.
P2
P3
PAGE 7www.fantasticfurniture.com.au
Step 3
You will need:
Phillips head screwdriver
- Insert 12 x Medium Dowels (H8) into Panels (P2)&(P3).- Attach and fix Panels (P4)&(P5) to Panels (P2)&(P3) using 20 x Large Screws (H10) as shown.
12 x Medium DowelsØ8 x 20 mm
(H8)
20 x Large ScrewsØ4 x 25 mm
(H10)
P2
P4
P5
P4P4
P5
P4
H10
H8
H10
H8P3
PAGE 8www.fantasticfurniture.com.au
Step 4
You will need:
Phillips head screwdriver
- Screw 4 x Cam Bolts (H1) to Panels (P2) & (P3).- Insert 20 x Large Dowels (H7) into Panels (P2)&(P3).
4 x Cam BoltsØ5 x 45 mm
(H1)
20 x Large DowelsØ8 x 30 mm
(H7)
P2
P3
P3P3
H7
H1
H1
H1
H1
H7
H7
H7
P2
P2
www.fantasticfurniture.com.au
Step 5
- Insert 4 x Medium Dowels (H8) into Panels (P1).- Screw 4 x Small Bolts (H6) to fix Panels (P1) to Panel (P2).
You will need:
Phillips head screwdriver
4 x Small BoltsØ6 x 20 mm
(H6)
4 x Medium DowelsØ8 x 20 mm
(H8)
Step 6
You will need:
Phillips head screwdriver
4 x Small BoltsØ6 x 20 mm
(H6)
4 x Medium DowelsØ8 x 20 mm
(H8)
P1
P1
H8
H8
H6
H6
P1
P1
H8
H8
H6
H6
P2
- Insert 4 x Medium Dowels (H8) into Panels (P1).- Screw 4 x Small Bolts (H6) to fix Panels (P1) to Panel (P3).
PAGE 9
P3
www.fantasticfurniture.com.au
Step 7
- Screw Panel (P6) to Panel (P7) with 2 x Small Bolts(H6).
You will need:
Phillips head screwdriver
Step 8
You will need:
Phillips headscrewdriver
2 x Small BoltsØ6 x 20 mm
(H6)
- Screw 4 x Cam Bolts (H1) to Panels (P8) & (P9).- Attach Panels (P10) to Panels (P8) & (P9) as shown.- Insert 4 x Cam Nuts (H2) into Panels (P10) make sure the arrow is pointing to the hole.-Turn the Cam Nuts (H2) 90◦ clockwise to tighten.
PAGE 10
4 x Cam BoltsØ5 x 45 mm
(H1)
4 x Cam NutsØ14.5 x 11.9 mm
(H2)
P8
P9
P10
P10
H2
H2
This is how a cam nut works........
The head of the cam bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt.
P7
P6H6
www.fantasticfurniture.com.au
Step 9
- Attach Panels (P9),(P10) to Panel (P2).- Insert 1 x Cam Nut (H2) into Panel (P10) make sure the arrow is pointing to the hole.- Turn the Cam Nut(H2) 90◦ clockwise to tighten.- Remark: Hold Panels (P9)& (P10) to avoid them from falling to damage the parts or structure until the end of Step 13.
You will need:
Phillips head screwdriver
Step 10
You will need:
Phillips headscrewdriver
-Attach Panel (P6) to Panel (P2).-Insert 2 x Barrel Nuts (H4) into Panel (P6).- Screw 2 x Large Bolts (H3) through Panel (P2) into Barrel Nuts (H4).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary. Hold Panel (P6) to avoid them from falling to damage the parts or structure until the end of Step 13.
PAGE 11
This is how a cam nut works........
The head of the cam bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt.
2 x Large BoltsØ6 x 50 mm
(H3)
2 x Barrel NutsØ9.5 x 11 mm
(H4)
P2P6
H3
H4Flat head
screwdriver
P6 P2
1 x Cam NutsØ14.5 x 11.9 mm
(H2)
P9P10
P2
H2
P10
H1
P2
www.fantasticfurniture.com.au
Step 11
-Attach Panels (P8),(P10) to Panel (P2).-Insert 1 x Cam Nut (H2) into Panel (P10) make sure the arrow is pointing to the hole.-Turn the Cam Nut(H2) 90◦ clockwise to tighten.-Remark:Hold Panels (P8)&(P10) to avoid them from falling to damage the parts or structure until the end of Step 13.
You will need:
Phillips head screwdriver
Step 12
You will need:
Phillips headscrewdriver
- Attach Panel (P11) to Panel (P2).- Insert 2 x Barrel Nuts (H4) into Panel (P11).- Screw 2 x Large Bolts (H3) through Panel (P2) into Barrel Nuts (H4)- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary. Hold Panel(P11) to avoid them from falling to damage the parts or structure until the end of Step 13.
PAGE 12
This is how a cam nut works........
The head of the cam bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt.
2 x Large BoltsØ6 x 50 mm
(H3)
2 x Barrel NutsØ9.5 x 11 mm
(H4)
Flat headscrewdriver
1 x Cam NutsØ14.5 x 11.9 mm
(H2)
P2
P11
P11P2
H3
H4
P2P8
P10
P2
P8
P10
H2
H1
www.fantasticfurniture.com.au
Step 13
- Attach Panels (P8),(P10),(P11) to Panel (P3) as shown.- Attach Panels (P6),(P9),(P10) to Panel (P3) as shown.- Insert 2 x Cam Nuts (H2) into Panels (P10) make sure the arrow is pointing to the hole, turn the Cam Nut (H2) 90◦ clockwise to tighten.- Insert 4 x Barrel Nuts (H4) into Panels (P6)&(P11).- Screw 4 x Large Bolts (H3) through Panel (P3) into Barrel Nuts in Panels (P6) & (P11).- Remark: Adjust position of Barrel Nuts (H4) using Flat head screwdriver if necessary.
You will need:
Phillips head screwdriver
PAGE 13
4 x Large BoltsØ6 x 50 mm
(H3)
4 x Barrel NutsØ9.5 x 11 mm
(H4)
Flat headscrewdriver
2 x Cam NutsØ14.5 x 11.9 mm
(H2)
This is how a cam nut works........
The head of the cam bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt.
P10
P8P11
P6
P9
P10
P3
H3
H3
H4
H4H2
H2
P6
P10
P3
P3
P11
P10
www.fantasticfurniture.com.au
Step 14
- Insert 4 x Large Dowels (H7) into Panel (P15).- Attach and fix Panels (P15),(P13) to Panel (P16) using 4 x Large Bolts (H3) as shown.
You will need:
Phillips head screwdriver
PAGE 14
4 x Large BoltsØ6 x 50 mm
(H3)
4 x Large DowelsØ8 x 30 mm
(H7)
P15
P13
P16
H3
H7
Step 15You will need:
Phillips head screwdriver
10 x Large BoltsØ6 x 50 mm
(H3)
4 x Large DowelsØ8 x 30 mm
(H7)
- Insert 4 x Large Dowels (H7) into Panels (P6).- Attach and fix Panels (P15)&(P16) to Panels (P2),(P3),(P6).- Insert 10 x Barrel Nuts (H4) into Panels (P15)&(P16).- Screw 10 x Large Bolts (H3) through Panel (P6) into Barrel Nuts (H4) in Panels (P15)&(P16).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
10 x Barrel NutsØ9.5 x 11 mm
(H4)
P2
P6 P3
P16P15
P6
P16
P16
P15
P2
P3
View Inside
H3
H4
H7
P6
H4
H3
You will need:
Phillips head screwdriver
2 x Small DowelsØ6 x 30 mm
(H9)
4 x Small ScrewsØ4 x 20 mm
(H11)
P15
P16
P17
P17H11
H9
- Insert 2 x Small Dowels (H9) into Panels (P15)&(P16).- Attach and fix Panel (P17) to Panels (P15)&(P16) using 4 x Small Screws (H11) as shown.
www.fantasticfurniture.com.au
Step 16
PAGE 15
Step 17
- Insert 4 x Large Dowels (H7) into Panel (P12).- Attach and fix Panels (P13)&(P14) to Panel (P12) using 4 x Large Bolts (H3) as shown.
You will need:
Phillips head screwdriver
4 x Large BoltsØ6 x 50 mm
(H3)
4 x Large DowelsØ8 x 30 mm
(H7)
P12
P13P14
H7
H11
www.fantasticfurniture.com.au PAGE 16
Step 18
You will need:
Phillips head screwdriver
10 x Large BoltsØ6 x 50 mm
(H3)
4 x Large DowelsØ8 x 30 mm
(H7)
10 x Barrel NutsØ9.5 x 11 mm
(H4)
P2P12
P14
P11
H7
P12
P14
P14
P12
H3
H4
H3
P11
P3
View Inside
- Insert 4 x Large Dowels (H7) into Panels (P11).- Attach and fix Panels (P12)&(P14) to Panels (P2),(P3),(P11).- Insert 10 x Barrel Nuts (H4) into Panels (P12)&(P14).- Screw 10 x Large Bolts (H3) through Panel (P11) into Barrel Nuts (H4) in Panels (P12)&(P14).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
P11
www.fantasticfurniture.com.au
Step 19
- Screw 2 x Cam Bolts (H1) to Panel (P18).
You will need:
Phillips head screwdriver
PAGE 17
Step 20
You will need:
Phillips head screwdriver
2 x Cam BoltsØ5 x 45 mm
(H1)P18
H1
2 x Cam NutsØ14.5 x 11.9 mm
(H2)
This is how a cam nut works........
The head of the cam bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt.
P18
P6
P18
P6H2
-Attach Panel (P18) to Panel (P6).-Insert 2 x Cam Nut (H2) into Panel (P6) make sure the arrow is pointing to the hole. Turn the Cam Nut (H2) 90◦ clockwise to tighten.
www.fantasticfurniture.com.au
Step 21
You will need:
Phillips head screwdriver
PAGE 18
- Insert 5 x Panels (P27) into the gaps of Panels (P4) & (P5).- Screw tight with 10 x Large Screws (H10).
10 x Large ScrewsØ4 x 25 mm
(H10)P5
H10
P27P4 P4
P4P4
P5
P5P27
P27
P27
H10
P5
www.fantasticfurniture.com.au
Step 22
You will need:
Phillips head screwdriver
PAGE 19
- Insert 2 x Panels (P28) into the gaps of Panels (P27).- Screw tight with 2 x Large Screws (H10) in the middle of the bed .
2 x Large ScrewsØ4 x 25 mm
(H10) P27
P28P27
P28
H10P28
P28
Step 23
You will need:
Phillips head screwdriver
3 x Large BoltsØ6 x 50 mm
(H3)
2 x Large DowelsØ8 x 30 mm
(H7)
3 x Barrel NutsØ9.5 x 11 mm
(H4)P20
P19 P19
P20H3
H7
H4
- Insert 2 x Large Dowels (H7) into Panel (P19).- Attach Panel (P19) to Panel (P20).- Insert 3 x Barrel Nuts (H4) into Panel (P19).- Screw 3 x Large Bolts(H3) through Panel (P20) into Barrel Nuts (H4) in Panel (P19).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
Flat headscrewdriver
www.fantasticfurniture.com.au
Step 24
PAGE 20
- Insert 2 x Large Dowels (H7) into Panel (P20).-Attach Panel (P24) to Panel (P20).- Insert 2 x Barrel Nuts (H4) into Panel (P20).- Screw 2 x Large Bolts (H3) through Panels (P24) into Barrel Nuts (H4) in Panel (P20).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
Step 25
You will need:
Phillips head screwdriver
2 x Large BoltsØ6 x 50 mm
(H3)
2 x Large DowelsØ8 x 30 mm
(H7)
2 x Barrel NutsØ9.5 x 11 mm
(H4)
You will need:
Phillips head screwdriver
2 x Large BoltsØ6 x 50 mm
(H3)
2 x Large DowelsØ8 x 30 mm
(H7)
2 x Barrel NutsØ9.5 x 11 mm
(H4)
P20
P24
P24
P20H3
H3
H7
H7
H4
P20
P25H3
H4
H7
Flat headscrewdriver
Flat headscrewdriver
- Insert 2 x Large Dowels (H7) into Panel (P20).-Attach Panel (P25) to Panel (P20).- Insert 2 x Barrel Nuts (H4) into Panel (P20).- Screw 2 x Large Bolts (H3) through Panels (P25) into Barrel Nuts (H4) in Panel (P20).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
H3
P25P20
H4
www.fantasticfurniture.com.au
Step 26
PAGE 21
- Insert 2 x Large Dowels (H7) into Panel (P21).- Attach Panel (P23) to Panel (P21).- Insert 2 x Barrel Nuts (H4) into Panel (P21).- Screw 2 x Large Bolts (H3) through Panel (P23) into Barrel Nuts (H4) in Panel (P21).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
Step 27
You will need:
Phillips head screwdriver
2 x Large BoltsØ6 x 50 mm
(H3)
2x Large DowelsØ8 x 30 mm
(H7)
2 x Barrel NutsØ9.5 x 11 mm
(H4)
You will need:
Phillips head screwdriver
2 x Large BoltsØ6 x 50 mm
(H3)
2 x Large DowelsØ8 x 30 mm
(H7)
2 x Barrel NutsØ9.5 x 11 mm
(H4)
P23
P23
P21
H3
H7
H4
H4
H3
H4
H7
H7
P22
Flat headscrewdriver
Flat headscrewdriver
- Insert 2 x Large Dowels (H7) into Panel (P21).- Attach Panel (P22) to Panel (P21).- Insert 2 x Barrel Nuts (H4) into Panel (P21).- Screw 2 x Large Bolts (H3) through Panels (P22) into Barrel Nuts (H4) in Panel (P21).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
H3H7
H4
P21
P21
P22P21
H3
www.fantasticfurniture.com.au
Step 28
PAGE 22
- Insert 4 x Barrel Nuts (H4) into Panels (P26).- Screw 4 x Large Bolts (H3) through Panels (P22)&(P23) into Barrel Nuts(H4) in Panels (P26).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
Step 29
You will need:
8x Large DowelsØ8 x 30 mm
(H7)
- Insert 8 x Large Dowels (H7) each into Panels (P2)& (P3).- Attach Panel (P22) on Panel (P2), Panel (P23) on Panel (P3).- Attach Panel (P24) on Panel (P2) , Panel (P25) on Panel(P3).
You will need:
Phillips head screwdriver
4 x Large BoltsØ6 x 50 mm
(H3)
4 x Barrel NutsØ9.5 x 11 mm
(H4)
P26
P26
P23
P22
H3
H3
H4
H4
P22
P24
P25
P2
P3P23
H7
H7
Flat headscrewdriver
www.fantasticfurniture.com.au
Step 30
PAGE 23
- Screw Panel (P21) into Panel (P18) using 2 x Large Screws (H10) from inside out.
You will need:
Phillips head screwdriver
2 x Large ScrewsØ4 x 25 mm
(H10)
P21
P21
P18
H10
View Inside
www.fantasticfurniture.com.au
Step 31
PAGE 24
- Insert 8 x Large Dowels (H7) into Panels (P4).- Place slats (P29) on top of lower mattress base.
You will need:
8x Large DowelsØ8 x 30 mm
(H7)
P29
P4
P4
H7
www.fantasticfurniture.com.au
Step 32
PAGE 25
- Place the mattress on top of Slats (P29).
P29
PAGE 26
Step 33
www.fantasticfurniture.com.au
- Lay Panels (P34)+(P37) flat as shown.
P34
P37
- Insert 2 x Large Dowels (H7) into Panel (P19).- Attach Panel (P19) to Panel (P20).- Insert 3 x Barrel Nuts (H4) into Panel (P19).- Screw 3 x Large Bolts(H3) through Panel (P20) into Barrel Nuts (H4) in Panel (P19).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
www.fantasticfurniture.com.au
Step 34
PAGE 27
- Screw 4 x Cam Bolts(H1) to Panels (P34) & (P37).- Insert 26 x Large Dowels (H7) into Panel (P34)&(P37) as shown.
You will need:
Phillips head screwdriver
4 x Cam BoltsØ5 x 45 mm
(H1)
26 x Large DowelsØ8 x 30 mm
(H7)
P34
H1
H7
P37
P37P37
H1
H1
H1
H7
H7H7
P34
P34
www.fantasticfurniture.com.au
Step 35
PAGE 28
- Insert 2 x Large Dowels (H7) into Panel (P32).- Attach Panel (P32) to Panel (P30).- Insert 3 x Barrel Nuts (H4) into Panel (P32).- Screw 3 x Large Bolts (H3) through Panel (P30) into Barrel Nuts (H4) in Panel (P32).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
Step 36
You will need:
Phillips head screwdriver
3 x Large BoltsØ6 x 50 mm
(H3)
2 x Large DowelsØ8 x 30 mm
(H7)
3 x Barrel NutsØ9.5 x 11 mm
(H4)
P32
P30H4
H3H7
You will need:
Phillips head screwdriver
3 x Large BoltsØ6 x 50 mm
(H3)
2 x Large DowelsØ8 x 30 mm
(H7)
3 x Barrel NutsØ9.5 x 11 mm
(H4)
P31
P32
H3
H7H4
Flat headscrewdriver
Flat headscrewdriver
- Insert 2 x Large Dowels (H7) into Panel (P20).-Attach Panel (P25) to Panel (P20).- Insert 2 x Barrel Nuts (H4) into Panel (P20).- Screw 2 x Large Bolts (H3) through Panels (P25) into Barrel Nuts (H4) in Panel (P20).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
- Insert 2 x Large Dowels (H7) into Panel (P32).- Attach Panel (P32) to Panel (P31).- Insert 3 x Barrel Nuts (H4) into Panel (P32).- Screw 3 x Large Bolts (H3) through Panel (P31) into Barrel Nuts (H4) in Panel (P32).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
P32H3
H4
P32
H3
H4
www.fantasticfurniture.com.au
Step 37
PAGE 29
Step 38
-Screw 4 x Cam Bolts (H1) into 2 x Panels (P33).- Attach 2 x Panels (P33) to 2 x Panels (P10) - Insert 4 x Cam Nuts (H2) into 2 x Panels (P10) make sure the arrow is pointing to the hole.-Turn the Cam Nut (H2) 90◦ clockwise to tighten.
You will need:
Phillips head screwdriver
4 x Cam BoltsØ5 x 45 mm
(H1)
4 x Cam NutsØ14.5 x 11.9 mm
(H2)
This is how a cam nut works........
The head of the cam bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt.
P10
P33H1
H2
You will need:
Phillips head screwdriver
2 x Large BoltsØ6 x 50 mm
(H3)
2 x Barrel NutsØ9.5 x 11 mm
(H4)
- Attach Panel (P30) to Panel (34).- Insert 2 x Barrel Nuts (H4) into Panel (P30).- Screw 2 x Large Bolts (H3) through Panel (P34) into Barrel Nuts (H4) in Panel (P30.)- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary. Hold Panel (P30) to avoid them from falling to damage the parts or structure until the end of Step 36.
P30
P34H3
H4
P34
P30Flat head
screwdriver
X2
- Insert 8 x Large Dowels (H7) each into Panels (P2)& (P3).- Attach Panel (P22) on Panel (P2), Panel (P23) on Panel (P3).- Attach Panel (P24) on Panel (P2) , Panel (P25) on Panel(P3).
www.fantasticfurniture.com.au
Step 39
PAGE 30
- Attach Panel (P31) to Panel (P34).- Insert 2 x Barrel Nuts (H4) into Panel (P31).- Screw 2 x Large Bolts (H3) through Panel (P34) into Barrel Nuts (H4) in Panel (P31).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary. Hold Panel (P31) to avoid them from falling to damage the parts or structure until the end of Step 36.
Step 40
You will need:
Phillips head screwdriver
2 x Large BoltsØ6 x 50 mm
(H3)
2 x Barrel NutsØ9.5 x 11 mm
(H4)
P31
P34
H3
H4
P31P34
- Attach 5x Panels (P35) to Panel (P34).- Insert 5 x Barrel Nuts (H4) into Panels (P35).- Screw 5 x Large Bolts (H3) through Panel (P34) into Barrel Nuts (H4) in Panels (P35).- Remark: Adjust position of Barrel Nuts (H4) by Flat head screwdriver if necessary.
You will need:
Phillips head screwdriver
5 x Large BoltsØ6 x 50 mm
(H3)
5 x Barrel NutsØ9.5 x 11 mm
(H4)
P34P35
P35
P35
P35
P35
H3
H4
Flat headscrewdriver
Flat headscrewdriver
- Screw Panel (P21) into Panel (P18) using 2 x Large Screws (H10) from inside out.
www.fantasticfurniture.com.au
Step 41
PAGE 31
- Attach Panels (P10)&(P33) to Panel (P34).-Insert 2 x Cam Nuts (H2) into 2 x Panels (P10) make sure the arrow is pointing to the hole.-Turn the Cam Nut (H2) 90◦ clockwise to tighten.
You will need:
Phillips head screwdriver
2 x Cam NutsØ14.5 x 11.9 mm
(H2)
This is how a cam nut works........
The head of the cam bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt.
Flat headscrewdriver
P33
P10H2
P33
P10
P34P33
P10
P33
P10 H2
P34
P34
www.fantasticfurniture.com.au
Step 42
PAGE 32
- Insert 4 x Barrel Nuts (H4) each into Panels (P30) & (P31).- Screw 4 x Large Bolts (H3) through Panel (P37) into the Barrel Nuts (H4) in Panels (P30) & (P31).- Insert 2 x Cam Nuts (H2) into 2 x Panels (P10) make sure the arrow is pointing to the hole. Turn the Cam Nut (H2) 90◦ clockwise to tighten.- Insert 5 x Barrel Nut (H4) into each Panel (P35).- Screw 5 x Large Bolts (H3) through Panel (P37) into Barrel Nuts (H4) in Panels (P35).- Remark: Adjust position of Barrel Nuts (H4) using Flat head screwdriver if necessary.
You will need:
Phillips head screwdriver
2 x Cam NutsØ14.5 x 11.9 mm
(H2)
This is how a cam nut works........
The head of the cam bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt.
Flat headscrewdriver
9 x Large BoltsØ6 x 50 mm
(H3)
9 x Barrel NutsØ9.5 x 11 mm
(H4)
P30
P37
P31
P10
P35P35
P35
P35
P30
P10
H2H4 P37
P31
P10
H2H4
P37
H3
H4
www.fantasticfurniture.com.au
Step 43
PAGE 33
- Insert 8 x Large Dowels (H7) into Panels (P22), (P23), (P24) & (P25).- Place Panels (P34)&(P37) onto Panels (P22) , (P24) , (P23),(P25) .-Remark:Pay attention to same direction of bed head.
You will need:
8 x Large DowelsØ8 x 30 mm
(H7)
P34
P22
P24
P23
P25
P37
H7
H7
H7
www.fantasticfurniture.com.au
Step 44
PAGE 34
- Screw Panel (P38 ) onto Panels (P34),(P24) & (P2) with 5 x Small Bolts (H6).- Apply the same method,Screw 1 x Panel (P38) onto Panels (P34),(P22) & (P2), 1 x Panel (P38) onto Panels (P37),(P25) & (P3) , 1 x Panel (P38) onto Panels (P37),(P23) & (P3) .
You will need:
20 x Small BoltsØ6 x 20 mm
(H6)Phillips head screwdriver
P34
P24
P22
P22
P24
P34
P34
P38
P38
H6
H6
P23
P25
P37
P2
P2
P3
www.fantasticfurniture.com.au
Step 45
PAGE 35
- Insert 2 x Medium Dowels (H8) into Panels (P34)&(P22).- Screw Panel (P39) onto (P34)&(P22) with 2 x Large Screws (H10).- Apply the same method, Screw 1 x Panel (P39) on to Panels (P34)&(P24), 1 x Panel (P39) on to Panels (P37)&(P25),1 x Panel (P39) on to Panels (P37)&(P23).
8 x Large ScrewsØ4 x 25 mm
(H10)
You will need:
Phillips head screwdriver
P34
P34
P22
P24
P25
P23
P37
P39
P22
P24
P34
P39
H10
H10H8
H8
8 x Medium DowelsØ8 x 20 mm
(H8)
www.fantasticfurniture.com.au
Step 46
PAGE 36
- Insert 12 x Large Dowels (H7) into 3 x Panels (P35).- Place 4 x Panels (P36) on Panels (P35).
You will need:
12 x Large DowelsØ8 x 30 mm
(H7)
P35P35
P36
H7
www.fantasticfurniture.com.au
Step 47
PAGE 37
- Screw the top of Ladder Handrail (P40) on Panel (P37) using 1 x Medium Bolt (H5). - Screw the middle of Ladder Handrail (P40) on Panel (P3) using 1 x Medium Bolt (H5).
You will need:
2 x Medium BoltsØ6 x 30 mm
(H5)
2 x Bolts(H12)
Phillips head screwdriver
P40
P40
P3
P37
P40
H5
H5
Step 48
You will need:
Phillips head screwdriver
P40
P41
P41
P41
P40
H12
- Insert Ladder Step (P41) into Ladder Handrail (P40).- Screw Ladder Step (P41) through Ladder Handrail (P40) using 1 x Bolt (H12) .- Repeat above sequence for the second Ladder Step (P41).
www.fantasticfurniture.com.au
Step 49
PAGE 38
- Insert 2 x Ladder Step (P41) into Ladder Handrail (P42).- Screw Ladder Step (P41) through Ladder Handrail (P42) using 2 x Bolt (H12)- Remark: Screw by hand & do not 100% tighten.- Screw the top of Ladder Handrail (P42) on Panel (P37) using 1 x Medium Bolt (H5). - Screw the middle of Ladder Handrail (P42) on Panel (P3) using 1 x Medium Bolt (H5).- Tighten all the 4 x Bolts (H12) in Ladder Handrail (P42).
You will need:
2 x Medium BoltsØ6 x 30 mm
(H5)
Phillips head screwdriver
Step 50
2x Bolts(H12) P41
P42P3
P37H12
H12H5
H5
Job Complete!In the interest of our environment please dispose of all packaging thoughtfully.