Vehicle Characteristics/Safety/Warnings and Cautions OPNET-MRAP-2 (IMG)-1

Vehicle Characteristics/Pre-Checks/ Driving/Winching

Introduction

Vehicle Characteristics/Safety/Warnings and Cautions OPNET-MRAP-2 (IMG)-2

MaxxPro Features

Length 240" to 264"Width 99"Height 115"Wheel Base 153" to 176"Ground Clearance (Center of Vehicle) 16.5"Ground Clearance (Differential Clearance)

14.4"

Angle of Approach 58°Angle of Departure 46° to 48°Gradeability 70% low rangeSide Slope 30%Mass Tare (GVM) 27,850 to 29,850 lbs.Payload 3,650 to 11,150 lbs.GVWR 31,500 to 39,000 lbs.Seating 2-man crew plus 4 to 10 passengersConfiguration 4x4Turning Circle 50' to 58'

Vehicle Characteristics/Safety/Warnings and Cautions OPNET-MRAP-2 (IMG)-3

• Fuel capacity is 70 gallons

• 372 miles per tank = 5.2 MPG

• 330 HP Diesel engine

• Run flat capability at 30 mph on a hard road for 30 miles

• Can be flat-towed by like vehicle

• Crew compartment sealed for NBC with proper ventilation to evacuate potential fumes

MaxxPro Capabilities

MaxxPro Features – Cont

Vehicle Characteristics/Safety/Warnings and Cautions OPNET-MRAP-2 (IMG)-4

• Operates in all climatic and environmental conditions

• Ford water up to 36 inches at speeds up to 5 mph without damage or without requiring maintenance before operation can continue

• Operates in temperatures from -25° F to 125° F without use of cold weather kit

MaxxPro Features – Cont

Vehicle Characteristics/Safety/Warnings and Cautions OPNET-MRAP-2 (IMG)-5

• Vehicle is designed to carry 6 personnel, including the driver

• Vehicle can support combat operations in urban environments and other restricted/confined spaces

MaxxPro Features

Vehicle Characteristics/Safety/Warnings and Cautions OPNET-MRAP-2 (IMG)-6

• Self-recovery winch

• Individual side facing rear seats

• Energy absorbing seats for blast protection

MaxxPro Features – Cont

Vehicle Characteristics/Safety/Warnings and Cautions OPNET-MRAP-2 (IMG)-7

• Front and rear tow points

• Air brakes system

• Gauges and indicators for driver

• Transparent armor windows

• Gross vehicle weight 37,000 lbs

MaxxPro Features – Cont

MaxxPro Features – Cont

REAR RAMP DOOR

Ramp control is located on the dash labeled ramp switch.

Be aware of personnel and surrounding before lowering ramp.

Ramp is hydraulically driven and comes down very fast.

MaxxPro Features

PRE- OPERATION CHECKS

MaxxPro Features – Pre check

Tires (All).

Check tread depth, tire inflation and even wear. Check tires for cuts, gouges, cracks, or other damage.

General Vehicle Walk.

Walk around the vehicle looking for obvious leaks.

Check for any damage.

Look for anything out of the norm.

MaxxPro Features – Pre Check

Engine Oil Level.

With engine off, pull dipstick out and wipe clean rag.

Re-insert dipstick to fully seat and pull back out.

Oil level should be between the Full and Add hash marks.

DO NOT OVERFILL.

MaxxPro Features

STARTING AND DRIVING

MaxxPro Features – Driving

Ensure Master power is on. Toggle switch being in the “down” position.

MaxxPro Features – Driving

Air Pressure.Low pressure indicator should not sound while in operation.Air pressure should be above 70 psi.

Air Pressure.Air pressure should be above 70 psi.Once air pressure is above 70 psi, push in the YELLOW park break knob.

Only press the RED trailer knob if towing a vehicle that uses air brakes.

MaxxPro Features – Cont

With the brake pedal pressed down push and hold the “D” drive button.

When putting vehicle in park, press the “N” neutral button before pulling the yellow park brake knob.

MaxxPro Features – Driving

The MaxxPro Plus is equipped with run flat tires that can be used when tire pressure is lower than the recommended range, at a speed no greater than 30 mph for 30 miles.

Flat Tire

MaxxPro Features

WINCHING

Winching Procedures

The MaxxPro Plus has a front-mounted, deployable self-recovery winch that is capable of pulling itself or an object like a door, barricade, or vehicles with same gross vehicle weight (GVW) out of a hole, mud, or other immobilized situation.

Winching Procedures

•Locate an anchor point suitable to the load.

•Rotate the clutch lever (1) to enable free-spooling of the winch drum.

•Pull out or “pay out” enough of the wire rope to reach the anchor point. When using Snatch block, pay out enough cable to reach back to truck

Paying Out Cable

1

Winching Procedures

Connecting Control Unit

Connect remote control unit (A) to remote connector (B).

BA B

MaxxPro Safety Considerations

•Roof Hatches• Must be open and closed while sitting still

•Rear Gate Open/Close• Check rear camera and door area for clear area• Ensure area is clear and announce “CLEAR!”

•Side doors• Air assist, keep hands, feet, and fingers clear• Close hard and latch inside to ensure doors don’t open while

turning•Backing Operations

• Use a ground guide, unless it is an emergency• Use backup camera if needed, it is equipped with a

microphone

MaxxPro Features – Cont

QUESTIONS?