update on mppc frontend electronics development at iu
DESCRIPTION
Update on MPPC frontend electronics development at IU. Gerard Visser. FEE for UCLA HCAL prototype. Single MPPC installed (#2 location). dark noise (+maybe small light leaks). on @ 72 V. off @ 67 V. Gang of four MPPC installed. dark noise (+maybe small light leaks). - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Update on MPPC frontend electronics development at IU](https://reader035.vdocuments.site/reader035/viewer/2022070410/56814573550346895db24372/html5/thumbnails/1.jpg)
Update on MPPC frontend electronics development at IU
Gerard Visser
September 26, 2013
![Page 2: Update on MPPC frontend electronics development at IU](https://reader035.vdocuments.site/reader035/viewer/2022070410/56814573550346895db24372/html5/thumbnails/2.jpg)
2calorimeter group meeting 9/26/2013
FEE for UCLA HCAL prototype
![Page 3: Update on MPPC frontend electronics development at IU](https://reader035.vdocuments.site/reader035/viewer/2022070410/56814573550346895db24372/html5/thumbnails/3.jpg)
3calorimeter group meeting 9/26/2013
Single MPPC installed (#2 location)dark noise (+maybe small light leaks)
on @ 72 V off @ 67 V
![Page 4: Update on MPPC frontend electronics development at IU](https://reader035.vdocuments.site/reader035/viewer/2022070410/56814573550346895db24372/html5/thumbnails/4.jpg)
4calorimeter group meeting 9/26/2013
Gang of four MPPC installeddark noise (+maybe small light leaks)
#2 on @ 72 V, others off @ 67 V all off @ 67 V
Note the histograms here and following in linear scale
![Page 5: Update on MPPC frontend electronics development at IU](https://reader035.vdocuments.site/reader035/viewer/2022070410/56814573550346895db24372/html5/thumbnails/5.jpg)
5calorimeter group meeting 9/26/2013
Gang of four MPPC, one at a time on
#2
#0
#3
#1
![Page 6: Update on MPPC frontend electronics development at IU](https://reader035.vdocuments.site/reader035/viewer/2022070410/56814573550346895db24372/html5/thumbnails/6.jpg)
6calorimeter group meeting 9/26/2013
Gang of four MPPC, #2 on vs. all on
#2 on @ 72 V, others off @ 67 V all on @ 72 V
It all looks pretty reasonable I think
p.s. – all signal volts/div on above slides are wrong by a factorof 2. too late to correct, and it doesn’t really matter anyway.
![Page 7: Update on MPPC frontend electronics development at IU](https://reader035.vdocuments.site/reader035/viewer/2022070410/56814573550346895db24372/html5/thumbnails/7.jpg)
7calorimeter group meeting 9/26/2013
Backup slides
![Page 8: Update on MPPC frontend electronics development at IU](https://reader035.vdocuments.site/reader035/viewer/2022070410/56814573550346895db24372/html5/thumbnails/8.jpg)
8calorimeter group meeting 9/26/2013
Requirements for FEE for UCLA W-SciFi calorimeter
• FEE fits behind tower (26.7 mm square), and compatible to optical coupling of MPPC’s to light guide
• Single analog output signal from tower, representing sum of 4 MPPC
• Full scale signal range (whole tower sum) >5,000 pixel with good linearity ≈1%.
• Noise level low enough to calibrate via single-pixel peak. (This is necessary to adjust each of 4 MPPC devices to matching gain).
• Temperature compensation and bias voltage stability sufficient to have ≈1% gain stability. (Over temperature range 25 to 40°C ?)
• Remark: 1% gain error results from merely ≈0.25 °C uncompensated temperature change.
• Low cost, low power, and easy to integrate to large system
(slightly updated from previous meeting)
![Page 9: Update on MPPC frontend electronics development at IU](https://reader035.vdocuments.site/reader035/viewer/2022070410/56814573550346895db24372/html5/thumbnails/9.jpg)
9calorimeter group meeting 9/26/2013
readout system
FEE block diagram
regulator+DAC
MPPCDAC
voltage reference
thermistor +preamp/ shaper
cable driver1-wire to
I2C bridge hardware
some software on some linux box somewhere
![Page 10: Update on MPPC frontend electronics development at IU](https://reader035.vdocuments.site/reader035/viewer/2022070410/56814573550346895db24372/html5/thumbnails/10.jpg)
10calorimeter group meeting 9/26/2013
Control system
local I2C devices
multidrop bus,unique global address factory programmed
100 kb/s 3.125 kb/s (×2) 62.5 DAC writes/s
while true; do { echo -ne 'rb5528DC6C920300009544\n' >/dev/ttyUSB0; sleep 0.8; echo -ne 'rb5528E26C920300006B44\n' >/dev/ttyUSB0; sleep 0.8; echo -ne 'rb5528DC6C9203000095BEFFFF\nrb5528E26C920300006BBEFFFF\n' >/dev/ttyUSB0; } done
(for example...)
$29.95 !!(need ~5 for beam test)