trident express tech bundle - poseidon service tools equipment express series plugs are set using a...

Multi Configuration Composite Body Bridge / Frac Plugs

unique combination of composites to provide a dependable, durable, and cost-efficient method for temporary zone isolation during stage fracs in both vertical and horizontal wells. The Express Series Plugs are constructed primarily from composite with cast iron slips ensuring fast drill times while remaining reliable.

The Express Series Plug is a multi-configuration plug allowing for a user to easily convert the tool from a Ball Drop to a Caged Ball or Bridge Plug. This conver-sion is easily obtained using two simple kits (Bridging Pin / Caged Ball Assembly). Express Series Plugs can be run with any wireline setting tool or tubing run hydraulic setting tool. Cast iron slips are hardened to wicker depth only and can be set in up to P110 casing.

is converted using a simple composite “Bridging Pin” that is threaded into the mandrel while sealing in the Inner Diameter. This plugged ID is drilled out before the top slip, thus allowing the upper and lower zones to equalize during drill out.

Express Series Ball Drop Frac: After the Ball Drop Frac Plug is set, the inner diameter remains open thus allowing wireline operators to continue work above. A ball is then dropped from the surface and pumped down until it seats on the tool. Once the ball is seated, the operator can pressure up against the Frac Plug.

Express Series Caged Ball Frac Plug: Similar to the Ball Drop Frac Plugs, although the Caged Ball Frac Plug houses the ball in the upper ID. This conversion is done using a simple composite Ball Caged adapter. When zonal pressure is greater from below the plug, the ball cage allows the lower and upper zones to comingle. When zonal pressure is greater from above, the ball seats thus isolating the zones.

Available in 4 ½” and 5 ½”. (other sizes pending)

Sets securely in up to P110 Grade Casing.

Compact and easy running.

Patent Pending

Consistent Drill Times of 13-20 minutes or less.

Utilizes unique “Lug” design on the top and muleshoe bottom ensuring that the plugs do not spin during drill out. Lug shoe also available.

Plugs are set using a universal setting sleeve and shear sleeve adapter.

Can be drilled using conventional tubing or coiled tubing.

Materials used in construction conducive to a wide range of environments.

Slips are only hardened to wicker depth for ease of drill out.

Pump Down Wiper available upon request.Bridge Ball Drop Caged Ball

The Express Series Bridge and Frac Plugs utilize a Express Series Bridge: The Express Series Bridge Plug

Express Series

Trident Frac Plugs by Poseidon 800-321-3780

Casing O.D. Part Number Overall

LengthCasing

Wt.MinI.D.

MaxI.D.

ToolO.D.

Operating Range Setting Tool

5 ” ECFP-5500-000 21.50” 13-23# 4.580 5.044 6K, 250 Deg Baker #10 / Baker #20 / 3 ” GO

5 ” ECFP-5500-001 24.00” 13-23# 4.580 5.044 4.425 8K, 275 Deg Baker #10 / Baker #20 / 3 ” GO

5 ” ECFP-5500-002 24.00” 13-23# 4.580 5.044 10K, 300 Deg Baker #10 / Baker #20 / 3 ” GO

5 ” ECBP-5500-000 21.50” 13-23# 4.580 5.044 4.425 6K, 250 Deg Baker #10 / Baker #20 / 3 ” GO



5 ” ECFP-5500-000CB 21.750” 13-23# 4.580 5.044 4.425 6K, 250 Deg Baker #10 / Baker #20 / 3 ” GO



Bridge

6k 8k 10k

Ball Drop Caged Ball

Pump Down Rubber

ECFP-4500-002 22.68” 9.5-15.1# 3.826 4.09 10K, 300 Deg Baker #10 / 3 ½" G.O.

ECFP-4500-001 22.68” 9.5-15.1# 3.826 4.09 3.609 8K, 275 Deg Baker #10 / 3 ½" G.O.

ECFP-4500-000 19.125” 9.5-15.1# 3.826 4.09 3.609 6K, 250 Deg Baker #10 / 3 ½" G.O.

ECBP-4500-002

ECBP-4500-001

ECBP-4500-000

22.68” 9.5-15.1# 3.826 4.09 10K, 300 Deg Baker #10 / 3 ½" G.O.

22.68” 9.5-15.1# 3.826 4.09 8K, 275 Deg Baker #10 / 3 ½" G.O.

19.125” 9.5-15.1# 3.826 4.09 6K, 250 Deg Baker #10 / 3 ½" G.O.

ECFP-4500-002CB 23.40” 9.5-15.1# 3.826 4.09 10K, 300 Deg Baker #10 / 3 ½" G.O.



4.425

4.425

3.609

3.609

3.609

3.609

3.609

3.609

3.609

4 ”

4 ”

4 ”

4 ”

4 ”

4 ”

4 ”

4 ”

4 ”

Express Series


Ball Drop Frac Plug Configuration

After the Ball Drop Frac Plug is set, the inner

diameter remains open thus allowing wireline

operators to continue work above. A ball is then

dropped from the surface and pumped down until

it seats on the tool. Once the ball is seated, the

operator can pressure up against the Frac Plug.

The Shear Sleeve Adapter used to set the plugs is

designed so that the user can, if needed, run the

Drop Ball “in place” inside the Adapter. This gives

the user to choice to utilize the plug as a Flow

Back Plug without having to drop the ball

from the surface.


LengthCasing

Wt.MinI.D.

MaxI.D.

ToolO.D.


4 ” ECFP-4500-002

4 ” ECFP-4500-001

4 ” ECFP-4500-000




Accessory Part Number

2” Composite Drop Ball for 5 ½" ECFP-5500-031

1 11/16" Composite Drop Ball for 4 ½" ECFP-4500-031

5 ” Pump Down Rubber 001758422555891

22.68” 9.5-15.1# 3.826 4.09 3.609 10K, 300 Deg Baker #10 / 3 ½" G.O.

22.68” 9.5-15.1# 3.826 4.09 3.609 8K, 275 Deg Baker #10 / 3 ½" G.O.

19.125” 9.5-15.1# 3.826 4.09 3.609 6K, 250 Deg Baker #10 / 3 ½" G.O.

Ball Drop

Express Series


Bridge Plug Configuration

The Express Series Bridge Plug is converted using

a simple composite “Bridging Pin” that is

threaded into the mandrel while sealing in the

Inner Diameter. This plugged ID is drilled out

before the top slip, thus allowing the upper and

lower zones to equalize during drill out.


LengthCasing

Wt.MinI.D.

MaxI.D.

ToolO.D.


4 ” ECBP-4500-002


22.68” 9.5-15.1# 3.826 4.09 3.609 10K, 300 Deg Baker #10 / 3 ½" G.O.

4 ” ECBP-4500-001 22.68” 9.5-15.1# 3.826 4.09 3.609 8K, 275 Deg Baker #10 / 3 ½" G.O.

4 ” ECBP-4500-000 19.125” 9.5-15.1# 3.826 4.09 3.609 6K, 250 Deg Baker #10 / 3 ½" G.O.




5 1/2" Composite Bridging Pin ECBP-5500-060

4 1/2" Composite Bridging Pin ECBP-4500-060

5 1/2" Pump Down Wiper 001758422555891

Bridge

Express Series


Caged Ball Frac Plug Configuration

The Express Series Caged Ball Frac utilizes a

simple Ball / Cage Adapter that houses a ¾”

Brass Ball in the upper ID of the plug. When

zonal pressure is greater from below the plug,

the ball cage allows the lower and upper

zones to comingle. When zonal pressure is

greater from above, the ball seats thus

isolating the zones.


LengthCasing

Wt.MinI.D.

MaxI.D.

ToolO.D.


4 ” ECFP-4500-002CB


23.40” 9.5-15.1# 3.826 4.09 3.609 10K, 300 Deg Baker #10 / 3 ½" G.O.

4 ” ECFP-4500-001CB 23.40” 9.5-15.1# 3.826 4.09 3.609 8K, 275 Deg Baker #10 / 3 ½" G.O.

4 ” ECFP-4500-000CB 19.375” 9.5-15.1# 3.826 4.09 3.609 6K, 250 Deg Baker #10 / 3 ½" G.O.




5 1/2" Composite Caged Ball Assembly ECFP-5500-108

4 1/2" Composite Caged Ball Assembly ECFP-4500-108

5 1/2" Pump Down Wiper 001758422555891

Caged Ball

Express Series


Setting Equipment

Express Series Plugs are set using a universal

Setting Sleeve and Setting Sleeve Adapter. Setting

kits are designed to be run on any wireline setting

tool or tubing run hydraulic setting tool with either

Baker #10, Baker #20 or 3 ½” G.O. connections.

The Shear Sleeve Adapter is placed around the top

of the plug and secured using seven steel shear

screws while the Setting Sleeve is installed around

the Shear Adapter and down to the top slip.

The Setting Assembly utilizes an Adjuster Nut that

mates the directly to the setting tool. The setting

sleeve is allowed to be threaded upwards past the

Adjuster Nut and secured onto the setting tool.

This allows the user to change out plugs on the

Sheer Sleeve Adapter without having to remove

the setting sleeve.

Part Number Description Overall Length Weld I.D.

EWST-BK10-203 Shear Sleeve Adapter – 5 ” on Baker #10 9.00” E5-1

EWST-BK20-ASM Setting Sleeve – 5 ” on Baker #20 22 7/16” E5-2

EWST-BK20-202 Shear Sleeve Adapter – 5 ” on Baker #20 9.00” E5-2

EWST-3625-ASM Setting Sleeve – 5 ” on 3 ” G.O. 22 7/16” E5-G

EWST-3625-180 Shear Sleeve Adapter – 5 ” on 3 ” G.O. 16.50” E5-G

ECFP-5500-028 Shear Screws for Shear Sleeve Adapter 9/16” N/A

Setting Sleeve Sleeve Adapter

EWST-BK10-ASM ” on Baker #10Setting Sleeve Assembly - 5 22 7/16” E5-1

EWST-3625-180-45 Setting Sleeve Adapter, 4 ½” on 3 ½” G.O E4-G

EWST-3625-ASM-45 Setting Sleeve, 4 ½” on 3 ½” G.O E4-G

EWST-BK10-180 Setting Sleeve Adapter, 4 ½” on Baker #10 9.73” E4-1

EWST-BK10-ASM-45 Setting Sleeve, 4 ½” on Baker #10 18.25” E4-1

Express Series


Composite Mutli-Configuration Plugs

Snug the tension sleeve correctly. Do not over tighten.

Be sure that nut is tightened correctly.

Do not allow the weight of the string to set on the

shoe of the plug when setting into well head.

Guide the plug through lubricator and rams before

setting lubricator in place. If the well has pressure on

it, be sure to raise tools to the top of the lubricator

before opening well head to pressure.

Running speed should be limited to 150 feet per

minute. Be extremely careful going into liner tops.

If you experience a misfire, do not pull out of hole any

faster than 150 feet per minute.

Never set plugs in casing collars.

Always set plugs in static well conditions.

Never perforate any closer than 50 feet to a plug.

Use bit and scraper in casing to remove any cement and scale from casing wall before you run any equipment that grips the casing.

Before running any plugs in hole, a junk basket and gage ring should be run for the appropriate size casing.

Choose correct size plug for casing. Composite Plugs usually cover the complete casing weight range.

Install the plug on the setting tool correctly. Do not over tighten.

Use correct setting tool size for the plug that you are running. Baker 10 or Go Compact for the 4 ½” and Baker #10, Baker #20 or Go Compact for the 5 ½” or larger.

All setting tools should be thoroughly redressed before each run.

Be sure that all oil levels are correct for the setting tool/temperature you are running.

Use the lock spring on all tools designed for use with a lock spring.

Express Series


Contact InformationPoseidon Rentals, LLC

17214 Saddlehorn

New Caney, TX 77357

800-321-3780

Account Management

D. Wade Maxwell Christina Maxwell

832-693-2966 281-785-7738

trident express tech bundle - poseidon service tools equipment express series plugs are set using a...

Documents