T Series

Confidential

Chapter 1. Disassembly & Assembly Guide1.MS-1-D.1

1-3. Disassembly & Assembly

- Main Section -

MS-1 Main Section Disassembly

T Series

Confidential

Battery Pack1)

1.MS-1-D.2

Battery Pack

Battery Lock (L)Battery Lock (R)

Remove the Battery Pack while moving the Battery Lock (L) and the Battery Lock (R) to the RELEASE side.

T Series

Confidential

Cover (L), Cover (R)1) 2)

1.MS-1-D.3

Remove the Cover (HL) in the direction of the arrow while outspreading its both sides and disengage the detent (two places).

Cover (HL)

Remove the nine screws from the Bottom.

Screw: Red-B7 / Blue-B8

3)

Raise the Cover (HR) vertically, and remove it.

Cover (HR)

Remark

Position of the detent

T Series

Confidential

Keyboard -11)

1.MS-1-D.4

3)

When the Keyboard can not be removed, insert the bamboo skewer from the back into the screw holes (three places) and release the keyboard.

Slide the Keyboard in the direction of the arrow, disengage the detent (four places) and turn down the front side.*The FPC is connected to the rear.

FPC

Keyboard

Remark

Disengage the detent (two places) and release the Keyboard.*Push the detent with the bamboo spatula and disengage it.

4)

Peel off the Cushion.

Cushion

KeyboardBack

T Series

Confidential

Keyboard -25)

1.MS-1-D.5

Disconnect the FPC.*Raise the connector and release the lock.

FPC

Connector

T Series

Confidential

Palmrest -11) 2)

1.MS-1-D.6

3)

Remove the three screws. Pull out the FFC (three places) vertically.

Pull the Palmrest toward the front, and raise the Palmrestto the front side while disengaging the detent (two places).*The detent is engaged toward the outside.

Remark

Screw: B7

Palmrest

Position of the detent

FFC

FFC

T Series

Confidential

Palmrest -25)

1.MS-1-D.7

FPC

Disconnect the FPC.*Disconnect the connector vertically.

Connector

T Series

Confidential

HDD1) 2)

1.MS-1-D.8

Remove the two screws.

Screw: B10

Disconnect the FPC.

FPC

3)

Remove the HDD.

HDD

Cushion

Peel off the Cushion (one place).

Hi Type

T Series

Confidential

Parts of the HDD1) 2)

1.MS-1-D.9

Remove the four screws.

Screw: B3

Remove the Bracket (two places).

Bracket

3)

Disconnect the FPC.*Use the tweezers and disconnect the connector portion little by little. * Be careful not to bend the pins.

Bracket

Connector

FPC

Hi Type

T Series

Confidential

HDD -1

1) 2)

1.MS-1-D.10

Remove the two screws.

Screw: B10

3)

Remove the Bracket (HDD).

Bracket (HDD)

4)

Disconnect the FPC.*Hold the connector and disconnect it vertically.

FPC

Connector

Peel off the Cushion.

Cushion

To Type

T Series

Confidential

HDD -25)

1.MS-1-D.11

Remove the HDD.

HDD

To Type

T Series

Confidential

Parts of the HDD1) 2)

1.MS-1-D.12

Remove the Cushion (HDD) (four places).Disconnect the FPC.*Use the tweezers and disconnect the connector portion little by little. * Be careful not to bend the pins.

Connector

Cushion (HDD)

FPC

To Type

T Series

Confidential

Memory1.MS-1-D.13

1)

Outspread the tabs (arrow 1) and pull out the Memory obliquely upward (arrow 2).

1

1

2

Tab

Memory

Remark

Memory is installed only in the following these models.1st --- T90S, T90PS, T160P,T170P

T Series

Confidential

Wireless LAN Card1.MS-1-D.14

1)

Outspread the tabs (arrow 1), and pull out the Wireless LAN Cardobliquely upward (in the direction of the arrow 2).

1

1

2Tab

Wireless LAN Card

T Series

Confidential

Optical Disc Drive, CNX-270 Board -1

1)

1.MS-1-D.15

Screw: B10

Remove the one screw.

2)

Remove the CNX Board from the Escutcheon (Front) and disconnect the FPC.*Pull out it in the direction of the arrow.

Insert a thin tool into the hole of the Bezel and pull out the Tray.

3)

Tray

Hole

4)

CNX Board

FPC

Cushion

Peel off the Cushion.

Escutcheon (Front)

T Series

Confidential

Optical Disc Drive, CNX-270 Board -25)

1.MS-1-D.16

Disconnect the connector and remove the Optical Disc Drive.

Connector

Disconnect the Harness and remove the CNX Board.

HarnessSide B

6)

7)

Remove the five screws.

Screw: B11

T Series

Confidential

CNX-273 Board -11) 2)

1.MS-1-D.17

3) 4)

Remove the one screw.* The screw secures the CNX Board together with the lug terminal.

Screw: B10

Disconnect the Harness (three places) and the FPC (one place).

Harness

Peel off the Tape (Harness).

Harness

FPC

Remove the convex portion of the Sheet from the hole.

Tape (Harness)

Sheet

Convex

Hole

T Series

Confidential

CNX-273 Board -25)

1.MS-1-D.18

Peel off the Kapton Tape and remove the CNX Board.*There is the Modem Card on the rear.

6)

Disconnect the Harness.

Peel off the Tape (Harness) (two places).

Tape (Harness)

Peel off the Sheet.

Sheet

7)

Kapton Tape

8)

Harness

CNX Board

T Series

Confidential

Modem Card -11)

1.MS-1-D.19

Remark

Remove the one screw.

Screw: B9 Side B

Remove the screw while securing the Nut of the side A with the 4 mm socket wrench.

Nut

Side A

2)

Modem Card

Side B

Disconnect the Modem Card.*There is the connector on the rear.

Connector

3)

Remove the Cushion.

Cushion

T Series

Confidential

Modem Card -21.MS-1-D.20

Remark

The Stand is installed under the Modem Card.

T Series

Confidential

1)

1.MS-1-D.21

LCD Section -12)

Remove the one screw.* The screw secures the lug terminal. Pull out the Harness (LCD) from under the Cover (L).

Screw: B6

3)

Remove the Cover (L) and the Cover (R) in the direction of the arrow while disengaging the detent (each one place).

Cover (L) Cover (R)

Harness (LCD)

Cover (L)

Cover (L)

Cover (R)

Position of the detent

Remark

T Series

Confidential

LCD Section -21.MS-1-D.22

Remove the two screws and the LCD.

Screw: B10

5)

LCD

4)

Disconnect the Harness (LCD).

Harness (LCD)

T Series

Confidential

Mother Board -11) 2)

1.MS-1-D.23

3) 4)

Remove the two screws and the Cover.

Screw: B10

Remove the three screws. Pull out the FPC (two places) vertically.

FPC

Screw: Red-B10 / Blue-B11

Cover

Peel off the Cushion.

Cushion

T Series

Confidential

Mother Board -25)

1.MS-1-D.24

Remove the Mother Board.*The connector portion is engaged with the Escutcheon (L).

Escutcheon (L)

Mother Board

T Series

Confidential

Escutcheon (Front), CNX-274 Board1)

1.MS-1-D.25

Escutcheon (Front)

Remove the one screw and the Escutcheon (Front).

Screw: B11

Peel off the Sheet (one place).

2)

3)

Peel off the Kapton Tape (one place) and Tape(Harness) (three places).

SheetTape (Harness)

KaptonTape

Remove the CNX Board.

CNX Board

4)

T Series

Confidential

Parts of the Escutcheon (Front)1)

1.MS-1-D.26

Remove the one screw on the both side in the right and the left.

Bracket

Remove the Bracket (two places) while disengaging the detent (each one place).

Speaker

3)

Remove the Speaker (two places).

2)

Screw: B1

T Series

Confidential

Escutcheon (L), Connector (VGA)

1)

1.MS-1-D.27

2)

3)

Remove the Escutcheon (L).

Escutcheon (L)

Connector (VGA)

Remove the Connector (VGA).

Peel off the Gasket (one place).

Gasket

T Series

Confidential

Parts of the Connector (VGA)1)

1.MS-1-D.28

2)

Bracket

Remove the Bracket.Remove the two screws.

Screw: B5

T Series

Confidential

Parts of the Housing (Bottom) -11)

1.MS-1-D.29

2)

3) 4)

Remove the Harness (two places).*The adhesive tapes are attached to the rear. Remove the Plate.

Plate

Remove the Escutcheon (R).

Escutcheon (R)

Remove the DC Jack while sliding it toward the front side.

DC Jack

HarnessAdhesive Tape

T Series

Confidential

Parts of the Housing (Bottom) -25)

1.MS-1-D.30

Remove the Sheet.

Sheet

Gasket

Sheet

Sheet

Cushion

Sheet

Spacer

Remark

The Sheet (three places), Gasket (one place), Cushion (one place) and Spacer (one place) are attached to the Housing (Bottom).

T Series

Confidential

Update History

Date Contents Version No.- - --

[ADD]---Addition [DEL]---Deletion [CHG]---Change [COR]---Correction [MA]---Model Addition