series 5470, non-impact resistant sliding glass door*min. of 3 threads beyond the metal substrate....
TRANSCRIPT
* MIN. OF 3 THREADSBEYOND THE METALSUBSTRATE.
FOR STEEL STUDS,MIN. FU=45 KSI &MIN. FY=33 KSI.
"UNGROUTED CMU" VALUESMAY BE USED FOR GROUTEDCMU APPLICATIONS.
DESIGN PRESSURE RATINGSEE TABLES 1, 2 & B1, B2
ON SHEETS 7 & 8
IMPACT RATING
GENERAL NOTES
VINYL SLIDING GLASS DOOR TDI
NTS 1 OF 25 TDI-SGD5470.2
J ROSOWSKI
3/24/16
Des
c.
Scal
e
Shee
t
DW
G
Serie
sTi
tle
No.
Rev
.
Dra
wn
By
Dat
e
A. LYNN MILLER, P.E. P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
Rev
AR
evB
Dat
eD
ate
Rev
AR
evB
No.
INSTRUCTIONS:1) KNOWING THE REQUIRED DESIGN PRESSURE OF THE OPENING, THE ANCHOR REQUIREMENTSFOR THE SLIDING GLASS DOORS MAY BE DETERMINED FROM DESIGN PRESSURE TABLES 1 OR 2,DEPENDING ON THE REINFORCEMENT LEVEL DESIRED.2) LOCATE THE SLIDING GLASS DOOR SIZE ON THE TABLE, USING THE FRAME HEIGHT AND THENOMINAL PANEL WIDTH IF YOUR EXACT SIZE IS NOT LISTED, ROUND UP TO THE NEXT GREATERLISTED WIDTH AND/OR HEIGHT.3) CHOOSE WHICH ANCHOR GROUP (A-D) IS MOST APPLICABLE. ANCHORS ARE DEFINED IN TABLEA, THIS SHEET, ALONG WITH THE CORRESPONDING SUBSTRATE, MINIMUM EMBEDMENT ANDMINIMUM EDGE DISTANCE.4) FROM THE DESIGN PRESSURE TABLES (TABLES 1 OR 2), VERIFY THAT THE OPENING'S REQUIREDDESIGN PRESSURE IS MET OR EXCEEDED. USE THE ANCHOR QUANTITIES SHOWN.5) INSTALL AS PER THE GUIDELINES OF THIS SHEET-SET.6) ADDITIONALLY, SEE THE EXAMPLE ON SHEET 9.
SERIES 5470, NON-IMPACT RESISTANT SLIDING GLASS DOORINCLUDING POCKETS & 90°/135° CORNERS
GENERAL NOTES:1) GLAZING TYPE OPTIONS: SEE GLAZING DETAILS ON SHEET 10.2) DESIGN PRESSURES:A. NEGATIVE DESIGN LOADS BASED ON TESTED PRESSURE AND GLASS PER ASTM E1300.B. POSITIVE DESIGN LOADS BASED ON TESTED PRESSURE, WATER TEST PRESSURE AND GLASS PER ASTM E1300.3) ANCHORAGE: THE 33-1/3% STRESS INCREASE HAS NOT BEEN USED IN THE DESIGN OF THIS PRODUCT. ANCHORSSHALL BE COATED OR CORROSION RESISTANT AS SPECIFIED IN THE 2006 TEXAS REVISIONS TO THE 2006INTERNATIONAL BUILDING CODE.4) SHUTTERS ARE REQUIRED PER IBC REQUIREMENTS, AS APPLICABLE.5) INSTALLATION SCREWS & FRAME SPLICES TO BE SEALED WITH NARROW JOINT SEALANT.6) REFERENCES (NOA'S): ELCO ULTRACON, CRETEFLEX & AGGREGATOR ANCHOR NOA'S, VISION EXTRUSION, LTD.WHITE RIGID PVC NOA, VE 1000 TAN 202 AND LIGHTER SHADES (NON-WHITE) RIGID PVC NOA AND BROWN COATED(PAINTED OR LAMINATED) WHITE RIGID PVC NOAREFERENCES (TEST REPORTS): FTL-6367, 6368, 6369, 6370, 6371, & 8545; EXOVA-10-002-792(A) & 10-006-10231;CAMBRIDGE 535753-09;7) DOOR SIZES MUST BE VERIFIED FOR COMPLIANCE WITH EGRESS REQUIREMENTS PER THE IBC, AS APPLICABLE.8) DRAWINGS DEPICT EXTERIOR-GLAZING, HOWEVER INTERIOR-GLAZING MAY BE SUBSTITUTED.9) THE 5470 SERIES SLIDING GLASS DOOR MAY ALSO BE KNOWN AS THE 470 SERIES.
ANCHOR NOTES:1) FOR CONCRETE/CMU SUBSTRATE APPLICATIONS, SEE TABLE A ON THIS SHEET FOR EMBEDMENT, EDGE DISTANCEAND SUBSTRATE REQUIREMENTS.2) FOR OTHER SUBSTRATE APPLICATIONS SEE TABLE A ON THIS SHEET.3) WOOD BUCKS DEPICTED AS 1X ARE LESS THAN 1-1/2" THICK. PROPERLY SECURED, 1X WOOD BUCKS ARE OPTIONALIF UNIT IS INSTALLED DIRECTLY TO SOLID CONCRETE OR CMU. WOOD BUCKS DEPICTED AS 2X ARE 1-1/2" THICK ORGREATER. 1X AND 2X BUCKS (WHEN USED) SHALL BE DESIGNED TO PROPERLY TRANSFER LOADS TO THE STRUCTURE.BUCK DESIGN AND INSTAL- LATION IS THE RESPONSIBILITY OF THE ENGINEER OR ARCHITECT OF RECORD & TO BEREVIEWED BY THE BUILDING OFFICIAL.4) IF SILL IS TIGHT TO SUBSTRATE, GROUT OR OTHER MATERIAL IS NOT REQUIRED. IF USED, NON-SHRINK,NON-METALLIC GROUT, MAX. 1/4" THICK & 3400 PSI MIN., (DONE BY OTHERS) MUST FULLY SUPPORT THE ENTIRELENGTH OF THE SILL THAT IS NOT TIGHT TO THE SUBSTRATE, AND TRANSFER SHEAR LOAD TO SUBSTRATE. IFSUBSTRATE IS WOOD, 30# FELT PAPER OR MASTIC IS REQUIRED BETWEEN THE GROUT AND WOOD SUBSTRATE, OR ASAPPROVED BY THE AUTHORITY HAVING JURISDICTION.
NOT RATED FOR MISSILEIMPACT RESISTANCE
SGD-5470
STANDARDS USED:2006 INTERNATIONAL BUILDING CODE (IBC)ASTM E1300-09ANSI/AF&PA NDS-2012 FOR WOOD CONSTRUCTIONALUMINUM DESIGN MANUAL, ADM-2010AISI-S100-07/S2-2010
TABLE A:
GENERAL NOTES.............EXAMPLE CONFIGS..........INSTALL DETAILS..............DP/ANCHOR TABLES........EXAMPLE............................GLAZING DETAILS............ANCHOR LOCATIONS.......PANEL TYPES...................EXTRUSIONS.....................ACCESSORIES..................SCREEN DETAILS.............PARTS LIST........................FIN ADDON INSTALL.........
123-67-891011-16171819202122-25
7/27/2017
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
X#
DETAIL LETTER
SHEET NUMBER
DETAIL G1135°
INSIDE CORNER
DETAIL H190°
INSIDE CORNER
DETAIL H290°
OUTSIDE CORNER
DETAIL G2135°
OUTSIDE CORNER
EXTERIOR
EXTERIOREXTERIOR
EXTERIOR
EXTERIOR
EXTERIOR
EXTERIOR
INTERIOR
INTERIOR
EXTERIOR
INTERIOR
INTERIOR
INTERIOR
INTERIOR
135°
135°90°
90°
EXAMPLE CONFIGURATIONS
NTS 2 OF 25
J ROSOWSKI
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) SEE SHEETS 14 & 15 FOR ANCHOR LOCATION & SPACING, FOR ANCHORQUANTITIES, SEE TABLES 1 & 2.3) CORNER ASTRAGAL MAY BE EITHER TO THE INTERIOR OR EXTERIOR,DEPENDING ON CONFIGURATION.
CORNER ASTRAGAL HORIZ. X-SECT.
NTS 5 OF 25
J ROSOWSKI
237 96
3619
69
26
96
96
69
9635
38
19
19
69
96
40
39
94
41
9619 69
40
39
94
41
33
33
37
33
33
INTERIOR
INTERIOR
INTERIOR
DLO WIDTH = NOM. PANEL WIDTH - 8-9/16"DLO HEIGHT = DOOR HEIGHT - 11-1/16"PANEL HEIGHT = DOOR HEIGHT - 2-1/2"
1
1
2
2
1
2
1
OR25
26OR25
26OR25
26OR25
7171
INTERIOR POCKETS MUSTINCLUDE A NON-STRUCTURAL,FRAME JAMB TO REDUCE THE
POSSIBILITY OF WATERINFILTRATION.
OPTIONAL NON-STRUCTURAL
ANCHORS FORINTERIOR POCKET
JAMB
INTERIOR POCKET
CONCRETE/CMUPER ANCHORREQUIREMENT
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER
SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
J ROSOWSKIP-HOOK EXAMPLES, HORIZ. X-SECT.
EMBEDMENT
EDGEDISTANCE
METAL TYP., ANCHOR LENGTHTO BE A MIN. OF 3 THREADS
BEYOND THE METAL SUBSTRATE
1/4"MAX.
EDGEDISTANCE
CONCRETE/CMUPER ANCHORREQUIREMENT
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER
SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEET 13 FOR ANCHOR LOCATION & SPACING, FOR ANCHOR QUANTITIES, SEE TABLES 1 & 2.4) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.5) INTERIOR OR EXTERIOR POCKETS APPLICABLE FOR ALL INSTALLATION METHODS.6) POCKET WALL OR CAVITY IS NOT PART OF THIS APPROVAL AND IS TO BE DESIGNED BY OTHERSAND REVIEWED BY THE AUTHORITY HAVING JURISDICTION.
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A,SHEET 1 & NOTE 3, BELOW
EMBEDMENT
1/4" MAX.
EXTERIOR POCKET
EXTERIOR POCKETEXTERIOR POCKET
DETAIL I2INTO MASONRY
DETAIL I3INTO METAL
1/4" MAX.
EXTERIOR
POCKET BY OTHERS, SEENOTE 6 BELOW.
EDGEDISTANCE
EMBED-MENT
DETAIL I1INTO MASONRY
EXTERIOR
INTERIOR
OPT.ANCHOR
33
30
21
18 OPT.17
10
SEE FIG 1,THIS SHEET
2728 OR
OPT. ANCHOR
EDGEDISTANCE
EMBEDMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHORNOTE 3, SHEET 1
EXTERIOR
DETAIL I4INTO WOOD
17
82
31
2728 OR
26
31
2728 OR
1/4" MAX.
EXTERIOR
EXTERIOR
FOR DOOR HEIGHTS OVER 96"
FOR DOOR HEIGHTS 96" AND LESS:
30
10
31
OPT. ANCHOR
OPT.ANCHOR
17
17
30
10
FIGURE 1, INTERLOCKS AT POCKETS:
1X OR 2X WOODBUCKSTRIP, SEEANCHOR NOTE 3,SHEET 1
EXTERIOR
DAYLIGHTOPENINGHEIGHT
DETAIL E1
.060 .060 .060
2.887 3.4644.041
DETAIL E3
FORLOCKSTILES,ASTRAGALS,FIXED STILES
ANDHORIZONTAL
RAILS
1.793
INTO MASONRY1X BUCKSTRIP
INTO MASONRY
EDGEDISTANCE
EMBED-MENT
EDGEDISTANCE
EMBEDMENT
FORINTERLOCKS
ONLY
FOR ALL LOCKSTILES,ASTRAGALS, FIXED
STILES ANDHORIZONTAL RAILS
#8 X 3/4" SMS REINFORCEMENTSCREW; 3 PER RAIL, LOCATED ATCENTERLINE AND 9" FROM ENDS(FACTORY INSTALLED)
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEET 13 FOR ANCHOR LOCATION & SPACING, FORANCHOR QUANTITIES, SEE TABLES 1 & 2.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED AT ALLFRAME ANCHOR LOCATIONS.5) PANEL WIDTH DOES NOT INCLUDE INTERLOCK OR ASTRAGAL ADD-ON.6) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS. ALLREINFORCEMENTS ARE APPROXIMATELY THE FULL LENGTH OFTHE EXTRUSION. REFER TO TEST REPORTS FOR EXACT DIMENSIONS.7) SEE SHEET 20 FOR SCREEN DETAILS.
REINFORCEMENT TYPES (SEE NOTE 6, THIS SHEET)
SEENOTE 6,
THIS SHEET
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600NTS 3 OF 25
J ROSOWSKI INSTALLATION, VERTICAL X-SECT.
NTS 4 OF 25
J ROSOWSKIINSTALLATION, HORIZONTAL X-SECT.
1/4" MAX.
EDGEDISTANCE
EMBEDMENT
EXTERIOR
DAYLIGHTOPENING
WIDTH
94
25
82
33
50
10
1X OR 2X WOODBUCKSTRIP, SEENOTE 4, SHEET 1
25
27 28
26
.060
1.917.823
SILL RISER SILL RISER SILL RISER SILL RISER
#42 SHOWN#43-45 ALSO APPLY
2.3702.947
SILL RISERVARIES WITH
REQUIREDPOSITIVEDESIGN
PRESSURE,SEE SHEETS
7 & 8.
CONCRETE/CMUPER ANCHOR
REQUIREMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHORNOTE 3, SHEET 1
EDGE DISTANCE
MULLION, ALUMINUM/STEELFRAMING OR STEEL STUD. MAYBE VERTICAL OR HORIZONTAL.SEE SUBSTRATE PROPERTIES,TABLE A, SHEET 1
EMBEDMENT
DETAIL E4INTO METAL
DETAIL E2INTO WOOD
1/4" MAX.1/4" MAX.
EDGEDISTANCE
EMBED-MENT
CONCRETE/CMUPER ANCHORREQUIREMENT
1/4" MAX.GROUT AS
NEEDED, SEEANCHOR NOTE
5, SHEET 1
DETAIL F1INTO MASONRY
EMBEDMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHOR
NOTE 3, SHEET 1
DETAIL F2INTO WOOD
1/4" MAX.1/4" MAX.
1/4" MAX.
1/4" MAX.
EMBEDMENT
EDGEDISTANCE
FRAMEHEIGHT
PANELHEIGHT
EXTERIOR
50
7
33
50
9
33
25
61 62
26
2
8
1
13
42 43 44 45
42
26
25
8
2-1/2" = TOTALSILL HEIGHT
.390.390
.390
.390
DLO WIDTH = NOM. PANEL WIDTH - 8-9/16"DLO HEIGHT = DOOR HEIGHT - 11-1/16"PANEL HEIGHT = DOOR HEIGHT - 2-1/2"
12
25 26OR25 26OR
OR
OR
71
82
81
STANDARD HD
32
6381
DETAIL A2INTO 2X WOOD
HORIZONTAL SECTION (XXX SHOWN)
DETAIL B2ASTRAGAL
ASTRAGAL MAY BEINSTALLED IN EITHERINTERIOR OREXTERIOR DIRECTION.ALL PARTS IDENTICAL.
FACING INT.
DETAIL C2INTERLOCK
DETAIL D2INTO MASONRY
1/4" MAX.
8
96
2291
21
19
31
CONCRETE/CMU PERANCHOR REQUIREMENT
TYP. ANCHOR TYPE,EMBEDMENT AND
EDGE DISTANCE PERSUBSTRATE, SEE
TABLE A, SHEET 1 &NOTE 3, BELOW
EMBEDMENT
EDGEDISTANCE
EDGEDISTANCE
METAL TYP., ANCHORLENGTH TO BE A MIN. OF 3THREADS BEYOND THEMETAL SUBSTRATE
TYP. ANCHOR TYPE,EMBEDMENT AND
EDGE DISTANCE PERSUBSTRATE, SEE
TABLE A, SHEET 1 &NOTE 3, BELOW
94
DETAIL A1THRU 1X WOOD
FRAME WIDTH
DETAIL B1ASTRAGAL DETAIL C1
INTERLOCKDETAIL D1
INTO METALFACING EXT.INTO MASONRY
27 28OR
29 #8 X 3/4" SMS REINFORCEMENT SCREW; 7PER STILE, LOCATED AT CENTERLINE AND 6",9" & 12" FROM ENDS (FACTORY INSTALLED).
1/4" MAX.
1/4" MAX.
EDGEDISTANCE
EMBEDMENT
EDGEDISTANCE
EMBEDMENT
PANEL WIDTH
TYP. ANCHOR TYPE,EMBEDMENT AND
EDGE DISTANCE PERSUBSTRATE, SEE
TABLE A, SHEET 1 &NOTE 3, BELOW
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHOR
NOTE 3, SHEET 1
8
96 DAYLIGHTOPENING
WIDTH
REQUIRED IF DOORHEIGHT IS OVER 96"
2291
21
71
2393
19
63
2526 OR2728 OR
31
HORIZONTAL SECTION (XO SHOWN)
TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A, SHEET1 & NOTE 3, BELOW
CONCRETE/CMU PERANCHOR REQUIREMENT
27
REQUIRED IF DOORHEIGHT IS OVER 96"
FIXED PANEL CLIP &ANCHORS, SEEDETAIL SHEET 19
EXTERIOR
EDGEDISTANCE
CONCRETE/CMU PERANCHOR REQUIREMENT
TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A,SHEET 1 & NOTE 3,THIS SHEET
TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A,SHEET 1 & NOTE 3,THIS SHEET
(2-1/2" TOTALSILL HEIGHT)
(3-1/2" TOTALSILL HEIGHT)
(4-1/16" TOTALSILL HEIGHT)
(4-5/8" TOTALSILL HEIGHT)
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A, SHEET1 & NOTE 3, THIS SHEET TYP. ANCHOR TYPE, EMBEDMENT
AND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A, SHEET1 & NOTE 3, THIS SHEET
TYP. ANCHOR TYPE, EMBEDMENT ANDEDGE DISTANCE PER SUBSTRATE, SEETABLE A, SHEET 1 & NOTE 3, THIS SHEET
TYP. ANCHOR TYPE, EMBEDMENT ANDEDGE DISTANCE PER SUBSTRATE, SEETABLE A, SHEET 1 & NOTE 3, THIS SHEET
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEETS 11 & 12 FOR ANCHOR LOCATION & SPACING,FOR ANCHOR QUANTITIES, SEE TABLES 1 & 2.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED ATALL FRAME ANCHOR LOCATIONS.5) SEE SHEET 20 FOR SCREEN DETAILS.6) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.ALL REINFORCEMENTS ARE APPROXIMATELY THE FULLLENGTH OF THE EXTRUSION. REFER TO TEST REPORTS FOREXACT DIMENSIONS.
INTERIOR
G
H5
5
CORNER, TYP.
90°
OR
135
° C
OR
NE
R
SEENOTE2, THISSHEET.
E4
F4
MAX. UNIT WIDTHNOM. PANEL WIDTH
PER TABLES 1 & 2
MAX. UNITHEIGHT
PERTABLES 1 & 2
A
F
B3
4
3
1-PANELCONFIGURATIONS
MAX. UNITHEIGHT
PER TABLES 1 & 2
SE
E N
OT
E 3 B
ELO
W
E4
I6
A3
E4
F4
C3
A3
E4
F4
D
I3
6
D
I3
6
MAX. UNIT WIDTHMAX. UNIT WIDTHMAX. UNIT WIDTH
NOM. PANEL WIDTHPER TABLES 1 & 2
POCKET POCKET POCKET
NOM. PANEL WIDTHPER TABLES 1 & 2
NOM. PANEL WIDTHPER TABLES 1 & 2
MAX. UNITHEIGHT
PER TABLES 1 & 2
MAX. UNITHEIGHT
PER TABLES 1 & 2
2-PANELCONFIGURATIONS
3-PANEL CONFIGURATIONS
A3
E4
F4
D
I3
6
MAX. UNIT WIDTH
NOM. PANEL WIDTHPER TABLES 1 & 2
MAX. UNITHEIGHT
PERTABLES 1 & 2
4-PANEL CONFIGURATIONS
A3
E4
F4
D3
MAX. UNIT WIDTH
NOM. PANEL WIDTHPER TABLES 1 & 2
MAX. UNITHEIGHT
PER TABLES 1 & 2
5-PANEL CONFIGURATIONS
E4
E4
F4
F4
A3
A3
D
I3
6
D3
MAX. UNIT WIDTH
NOM. PANEL WIDTHPER TABLES 1 & 2
NOM. PANEL WIDTHPER TABLES 1 & 2
MAX. UNITHEIGHT
PER TABLES 1 & 2
6-PANEL CONFIGURATIONS
7-PANEL CONFIGURATIONS
MAX. UNIT WIDTH
E4
F4
A3
D3
MAX. UNIT WIDTH
NOM. PANEL WIDTHPER TABLES 1 & 2
MAX. UNITHEIGHT
PER TABLES 1 & 2
8-PANEL CONFIGURATIONS
CONFIGURATIONS NOTES:
1) ALL CONFIGURATIONS SHOWN ARE ALSO AVAILABLE AS POCKET CONFIGURATIONS AT EITHER OR BOTH JAMBLOCATIONS. EXAMPLE: 4-PANEL XXXX IN POCKET (p) CONFIGURATION CAN BE pXXXXp, pXXXX OR XXXXp. OXXX INPOCKET CONFIGURATION CAN BE OXXXp.
2) 90° & 135° CORNER CONFIGURATIONS ARE A COMBINATION OF ANY 2 STRAIGHT CONFIGURATIONS.
3) POCKET WALL OR CAVITY IS NOT PART OF THIS APPROVAL AND IS TO BE DESIGNED BY OTHERS ANDREVIEWED BY THE AUTHORITY HAVING JURISDICTION.
4) FOR NOM. PANEL WIDTH, SEE TABLES 1 & 2.
I6
I6
I6
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
B3C3
OUTSIDE CORNER SHOWN, INSIDE CORNER SIMILAR
MAX. UNITHEIGHT
PER TABLES 1 & 2
"X" = OPERABLE PANEL"O" = INOPERABLE PANEL"p" = POCKET
SE
E N
OT
E 3 B
ELO
W
SE
E N
OT
E 3 B
ELO
W
SE
E N
OT
E 3 B
ELO
W
SE
E N
OT
E 3 B
ELO
W
SE
E N
OT
E 3 B
ELO
W
SE
E N
OT
E 3 B
ELO
W
SE
E N
OT
E 3 B
ELO
W
NTS 6 OF 25
9121
2221 91
2221
91
97 21.9"MAX. O.C.
28OR
SEE NOTE 6, THIS SHEET
SEE NOTE 6,THIS SHEET SEE NOTE 6,
THIS SHEET
SEE NOTE 6,THIS SHEET
SEE NOTE 6, THIS SHEET
INTERIOR
35
OPT.
OPT. OPT.
SEE FIG 1,THIS SHEET
SEE FIG 1,THIS SHEET
SEE FIG 1,THIS SHEET
8
8
8
8 88
8
8
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 28" O.C.
ANCHORPLATE AT
EVERYANCHOR
LOCATION
8
ANCHOR PLATE ATEVERY ANCHOR
LOCATION
8
22
SGD-5470 SGD-5470 SGD-5470 SGD-5470 SGD-5470
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
DETAIL G1135°
INSIDE CORNER
DETAIL H190°
INSIDE CORNER
DETAIL H290°
OUTSIDE CORNER
DETAIL G2135°
OUTSIDE CORNER
EXTERIOR
EXTERIOREXTERIOR
EXTERIOR
EXTERIOR
EXTERIOR
EXTERIOR
INTERIOR
INTERIOR
EXTERIOR
INTERIOR
INTERIOR
INTERIOR
INTERIOR
135°
135°90°
90°
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) SEE SHEETS 14 & 15 FOR ANCHOR LOCATION & SPACING, FOR ANCHORQUANTITIES, SEE TABLES 1 & 2.3) CORNER ASTRAGAL MAY BE EITHER TO THE INTERIOR OR EXTERIOR,DEPENDING ON CONFIGURATION.
CORNER ASTRAGAL HORIZ. X-SECT.
NTS 5 OF 25
J ROSOWSKI
237 96
3619
69
26
96
96
69
9635
38
19
19
69
96
40
39
94
41
9619 69
40
39
94
41
33
33
37
33
33
INTERIOR
INTERIOR
INTERIOR
1
1
2
2
1
2
1
OR25
26OR25
26OR25
26OR25
7171
INTERIOR POCKETS MUSTINCLUDE A NON-STRUCTURAL,FRAME JAMB TO REDUCE THE
POSSIBILITY OF WATERINFILTRATION.
OPTIONAL NON-STRUCTURAL
ANCHORS FORINTERIOR POCKET
JAMB
INTERIOR POCKET
CONCRETE/CMUPER ANCHORREQUIREMENT
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER
SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
J ROSOWSKIP-HOOK EXAMPLES, HORIZ. X-SECT.
EMBEDMENT
EDGEDISTANCE
METAL TYP., ANCHOR LENGTHTO BE A MIN. OF 3 THREADS
BEYOND THE METAL SUBSTRATE
1/4"MAX.
EDGEDISTANCE
CONCRETE/CMUPER ANCHORREQUIREMENT
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER
SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEET 13 FOR ANCHOR LOCATION & SPACING, FOR ANCHOR QUANTITIES, SEE TABLES 1 & 2.4) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.5) INTERIOR OR EXTERIOR POCKETS APPLICABLE FOR ALL INSTALLATION METHODS.6) POCKET WALL OR CAVITY IS NOT PART OF THIS APPROVAL AND IS TO BE DESIGNED BY OTHERSAND REVIEWED BY THE AUTHORITY HAVING JURISDICTION.
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A,SHEET 1 & NOTE 3, BELOW
EMBEDMENT
1/4" MAX.
EXTERIOR POCKET
EXTERIOR POCKETEXTERIOR POCKET
DETAIL I2INTO MASONRY
DETAIL I3INTO METAL
1/4" MAX.
EXTERIOR
POCKET BY OTHERS, SEENOTE 6 BELOW.
EDGEDISTANCE
EMBED-MENT
DETAIL I1INTO MASONRY
EXTERIOR
INTERIOR
OPT.ANCHOR
33
30
21
18 OPT.17
10
SEE FIG 1,THIS SHEET
2728 OR
OPT. ANCHOR
EDGEDISTANCE
EMBEDMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHORNOTE 3, SHEET 1
EXTERIOR
DETAIL I4INTO WOOD
17
82
31
2728 OR
26
31
2728 OR
1/4" MAX.
EXTERIOR
EXTERIOR
FOR DOOR HEIGHTS OVER 96"
FOR DOOR HEIGHTS 96" AND LESS:
30
10
31
OPT. ANCHOR
OPT.ANCHOR
17
17
30
10
FIGURE 1, INTERLOCKS AT POCKETS:
1X OR 2X WOODBUCKSTRIP, SEEANCHOR NOTE 3,SHEET 1
EXTERIOR
DAYLIGHTOPENINGHEIGHT
DETAIL E1
.060 .060 .060
2.887 3.4644.041
DETAIL E3
FORLOCKSTILES,ASTRAGALS,FIXED STILES
ANDHORIZONTAL
RAILS
1.793
INTO MASONRY1X BUCKSTRIP
INTO MASONRY
EDGEDISTANCE
EMBED-MENT
EDGEDISTANCE
EMBEDMENT
FORINTERLOCKS
ONLY
FOR ALL LOCKSTILES,ASTRAGALS, FIXED
STILES ANDHORIZONTAL RAILS
#8 X 3/4" SMS REINFORCEMENTSCREW; 3 PER RAIL, LOCATED ATCENTERLINE AND 9" FROM ENDS(FACTORY INSTALLED)
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEET 13 FOR ANCHOR LOCATION & SPACING, FORANCHOR QUANTITIES, SEE TABLES 1 & 2.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED AT ALLFRAME ANCHOR LOCATIONS.5) PANEL WIDTH DOES NOT INCLUDE INTERLOCK OR ASTRAGAL ADD-ON.6) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS. ALLREINFORCEMENTS ARE APPROXIMATELY THE FULL LENGTH OFTHE EXTRUSION. REFER TO TEST REPORTS FOR EXACT DIMENSIONS.7) SEE SHEET 20 FOR SCREEN DETAILS.
REINFORCEMENT TYPES (SEE NOTE 6, THIS SHEET)
SEENOTE 6,
THIS SHEET
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600NTS 3 OF 25
J ROSOWSKI INSTALLATION, VERTICAL X-SECT.
NTS 4 OF 25
J ROSOWSKIINSTALLATION, HORIZONTAL X-SECT.
1/4" MAX.
EDGEDISTANCE
EMBEDMENT
EXTERIOR
DAYLIGHTOPENING
WIDTH
94
25
82
33
50
10
1X OR 2X WOODBUCKSTRIP, SEENOTE 4, SHEET 1
25
27 28
26
.060
1.917.823
SILL RISER SILL RISER SILL RISER SILL RISER
#42 SHOWN#43-45 ALSO APPLY
2.3702.947
SILL RISERVARIES WITH
REQUIREDPOSITIVEDESIGN
PRESSURE,SEE SHEETS
7 & 8.
CONCRETE/CMUPER ANCHOR
REQUIREMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHORNOTE 3, SHEET 1
EDGE DISTANCE
MULLION, ALUMINUM/STEELFRAMING OR STEEL STUD. MAYBE VERTICAL OR HORIZONTAL.SEE SUBSTRATE PROPERTIES,TABLE A, SHEET 1
EMBEDMENT
DETAIL E4INTO METAL
DETAIL E2INTO WOOD
1/4" MAX.1/4" MAX.
EDGEDISTANCE
EMBED-MENT
CONCRETE/CMUPER ANCHORREQUIREMENT
1/4" MAX.GROUT AS
NEEDED, SEEANCHOR NOTE
5, SHEET 1
DETAIL F1INTO MASONRY
EMBEDMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHOR
NOTE 3, SHEET 1
DETAIL F2INTO WOOD
1/4" MAX.1/4" MAX.
1/4" MAX.
1/4" MAX.
EMBEDMENT
EDGEDISTANCE
FRAMEHEIGHT
PANELHEIGHT
EXTERIOR
50
7
33
50
9
33
25
61 62
26
2
8
1
13
42 43 44 45
42
26
25
8
2-1/2" = TOTALSILL HEIGHT
.390.390
.390
.390
DLO WIDTH = NOM. PANEL WIDTH - 8-9/16"DLO HEIGHT = DOOR HEIGHT - 11-1/16"PANEL HEIGHT = DOOR HEIGHT - 2-1/2"
12
25 26OR25 26OR
OR
OR
71
82
81
STANDARD HD
32
6381
DETAIL A2INTO 2X WOOD
HORIZONTAL SECTION (XXX SHOWN)
DETAIL B2ASTRAGAL
ASTRAGAL MAY BEINSTALLED IN EITHERINTERIOR OREXTERIOR DIRECTION.ALL PARTS IDENTICAL.
FACING INT.
DETAIL C2INTERLOCK
DETAIL D2INTO MASONRY
1/4" MAX.
8
96
2291
21
19
31
CONCRETE/CMU PERANCHOR REQUIREMENT
TYP. ANCHOR TYPE,EMBEDMENT AND
EDGE DISTANCE PERSUBSTRATE, SEE
TABLE A, SHEET 1 &NOTE 3, BELOW
EMBEDMENT
EDGEDISTANCE
EDGEDISTANCE
METAL TYP., ANCHORLENGTH TO BE A MIN. OF 3THREADS BEYOND THEMETAL SUBSTRATE
TYP. ANCHOR TYPE,EMBEDMENT AND
EDGE DISTANCE PERSUBSTRATE, SEE
TABLE A, SHEET 1 &NOTE 3, BELOW
94
DETAIL A1THRU 1X WOOD
FRAME WIDTH
DETAIL B1ASTRAGAL DETAIL C1
INTERLOCKDETAIL D1
INTO METALFACING EXT.INTO MASONRY
27 28OR
29 #8 X 3/4" SMS REINFORCEMENT SCREW; 7PER STILE, LOCATED AT CENTERLINE AND 6",9" & 12" FROM ENDS (FACTORY INSTALLED).
1/4" MAX.
1/4" MAX.
EDGEDISTANCE
EMBEDMENT
EDGEDISTANCE
EMBEDMENT
PANEL WIDTH
TYP. ANCHOR TYPE,EMBEDMENT AND
EDGE DISTANCE PERSUBSTRATE, SEE
TABLE A, SHEET 1 &NOTE 3, BELOW
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHOR
NOTE 3, SHEET 1
8
96 DAYLIGHTOPENING
WIDTH
REQUIRED IF DOORHEIGHT IS OVER 96"
2291
21
71
2393
19
63
2526 OR2728 OR
31
HORIZONTAL SECTION (XO SHOWN)
TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A, SHEET1 & NOTE 3, BELOW
CONCRETE/CMU PERANCHOR REQUIREMENT
27
REQUIRED IF DOORHEIGHT IS OVER 96"
FIXED PANEL CLIP &ANCHORS, SEEDETAIL SHEET 19
EXTERIOR
EDGEDISTANCE
CONCRETE/CMU PERANCHOR REQUIREMENT
TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A,SHEET 1 & NOTE 3,THIS SHEET
TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A,SHEET 1 & NOTE 3,THIS SHEET
(2-1/2" TOTALSILL HEIGHT)
(3-1/2" TOTALSILL HEIGHT)
(4-1/16" TOTALSILL HEIGHT)
(4-5/8" TOTALSILL HEIGHT)
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A, SHEET1 & NOTE 3, THIS SHEET TYP. ANCHOR TYPE, EMBEDMENT
AND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A, SHEET1 & NOTE 3, THIS SHEET
TYP. ANCHOR TYPE, EMBEDMENT ANDEDGE DISTANCE PER SUBSTRATE, SEETABLE A, SHEET 1 & NOTE 3, THIS SHEET
TYP. ANCHOR TYPE, EMBEDMENT ANDEDGE DISTANCE PER SUBSTRATE, SEETABLE A, SHEET 1 & NOTE 3, THIS SHEET
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEETS 11 & 12 FOR ANCHOR LOCATION & SPACING,FOR ANCHOR QUANTITIES, SEE TABLES 1 & 2.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED ATALL FRAME ANCHOR LOCATIONS.5) SEE SHEET 20 FOR SCREEN DETAILS.6) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.ALL REINFORCEMENTS ARE APPROXIMATELY THE FULLLENGTH OF THE EXTRUSION. REFER TO TEST REPORTS FOREXACT DIMENSIONS.
INTERIOR
NTS 6 OF 25
9121
2221 91
2221
91
97 21.9"MAX. O.C.
28OR
SEE NOTE 6, THIS SHEET
SEE NOTE 6,THIS SHEET SEE NOTE 6,
THIS SHEET
SEE NOTE 6,THIS SHEET
SEE NOTE 6, THIS SHEET
INTERIOR
35
OPT.
OPT. OPT.
SEE FIG 1,THIS SHEET
SEE FIG 1,THIS SHEET
SEE FIG 1,THIS SHEET
8
8
8
8 88
8
8
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 28" O.C.
ANCHORPLATE AT
EVERYANCHOR
LOCATION
8
ANCHOR PLATE ATEVERY ANCHOR
LOCATION
8
22
SGD-5470 SGD-5470 SGD-5470 SGD-5470
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
DETAIL G1135°
INSIDE CORNER
DETAIL H190°
INSIDE CORNER
DETAIL H290°
OUTSIDE CORNER
DETAIL G2135°
OUTSIDE CORNER
EXTERIOR
EXTERIOREXTERIOR
EXTERIOR
EXTERIOR
EXTERIOR
EXTERIOR
INTERIOR
INTERIOR
EXTERIOR
INTERIOR
INTERIOR
INTERIOR
INTERIOR
135°
135°90°
90°
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) SEE SHEETS 14 & 15 FOR ANCHOR LOCATION & SPACING, FOR ANCHORQUANTITIES, SEE TABLES 1 & 2.3) CORNER ASTRAGAL MAY BE EITHER TO THE INTERIOR OR EXTERIOR,DEPENDING ON CONFIGURATION.
CORNER ASTRAGAL HORIZ. X-SECT.
NTS 5 OF 25
J ROSOWSKI
237 96
3619
69
26
96
96
69
9635
38
19
19
69
96
40
39
94
41
9619 69
40
39
94
41
33
33
37
33
33
INTERIOR
INTERIOR
INTERIOR
1
1
2
2
1
2
1
OR25
26OR25
26OR25
26OR25
7171
INTERIOR POCKETS MUSTINCLUDE A NON-STRUCTURAL,FRAME JAMB TO REDUCE THE
POSSIBILITY OF WATERINFILTRATION.
OPTIONAL NON-STRUCTURAL
ANCHORS FORINTERIOR POCKET
JAMB
INTERIOR POCKET
CONCRETE/CMUPER ANCHORREQUIREMENT
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER
SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
J ROSOWSKIP-HOOK EXAMPLES, HORIZ. X-SECT.
EMBEDMENT
EDGEDISTANCE
METAL TYP., ANCHOR LENGTHTO BE A MIN. OF 3 THREADS
BEYOND THE METAL SUBSTRATE
1/4"MAX.
EDGEDISTANCE
CONCRETE/CMUPER ANCHORREQUIREMENT
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER
SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEET 13 FOR ANCHOR LOCATION & SPACING, FOR ANCHOR QUANTITIES, SEE TABLES 1 & 2.4) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.5) INTERIOR OR EXTERIOR POCKETS APPLICABLE FOR ALL INSTALLATION METHODS.6) POCKET WALL OR CAVITY IS NOT PART OF THIS APPROVAL AND IS TO BE DESIGNED BY OTHERSAND REVIEWED BY THE AUTHORITY HAVING JURISDICTION.
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A,SHEET 1 & NOTE 3, BELOW
EMBEDMENT
1/4" MAX.
EXTERIOR POCKET
EXTERIOR POCKETEXTERIOR POCKET
DETAIL I2INTO MASONRY
DETAIL I3INTO METAL
1/4" MAX.
EXTERIOR
POCKET BY OTHERS, SEENOTE 6 BELOW.
EDGEDISTANCE
EMBED-MENT
DETAIL I1INTO MASONRY
EXTERIOR
INTERIOR
OPT.ANCHOR
33
30
21
18 OPT.17
10
SEE FIG 1,THIS SHEET
2728 OR
OPT. ANCHOR
EDGEDISTANCE
EMBEDMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHORNOTE 3, SHEET 1
EXTERIOR
DETAIL I4INTO WOOD
17
82
31
2728 OR
26
31
2728 OR
1/4" MAX.
EXTERIOR
EXTERIOR
FOR DOOR HEIGHTS OVER 96"
FOR DOOR HEIGHTS 96" AND LESS:
30
10
31
OPT. ANCHOR
OPT.ANCHOR
17
17
30
10
FIGURE 1, INTERLOCKS AT POCKETS:
1X OR 2X WOODBUCKSTRIP, SEEANCHOR NOTE 3,SHEET 1
EXTERIOR
DAYLIGHTOPENINGHEIGHT
DETAIL E1
.060 .060 .060
2.887 3.4644.041
DETAIL E3
FORLOCKSTILES,ASTRAGALS,FIXED STILES
ANDHORIZONTAL
RAILS
1.793
INTO MASONRY1X BUCKSTRIP
INTO MASONRY
EDGEDISTANCE
EMBED-MENT
EDGEDISTANCE
EMBEDMENT
#8 X 3/4" SMS REINFORCEMENTSCREW; 3 PER RAIL, LOCATED ATCENTERLINE AND 9" FROM ENDS(FACTORY INSTALLED)
SEENOTE 6,
THIS SHEET
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
INSTALLATION, VERTICAL X-SECT.
NTS 4 OF 25
J ROSOWSKI
.060
1.917.823
SILL RISER SILL RISER SILL RISER SILL RISER
#42 SHOWN#43-45 ALSO APPLY
2.3702.947
SILL RISERVARIES WITH
REQUIREDPOSITIVEDESIGN
PRESSURE,SEE SHEETS
7 & 8.
CONCRETE/CMUPER ANCHOR
REQUIREMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHORNOTE 3, SHEET 1
EDGE DISTANCE
MULLION, ALUMINUM/STEELFRAMING OR STEEL STUD. MAYBE VERTICAL OR HORIZONTAL.SEE SUBSTRATE PROPERTIES,TABLE A, SHEET 1
EMBEDMENT
DETAIL E4INTO METAL
DETAIL E2INTO WOOD
1/4" MAX.1/4" MAX.
EDGEDISTANCE
EMBED-MENT
CONCRETE/CMUPER ANCHORREQUIREMENT
1/4" MAX.GROUT AS
NEEDED, SEEANCHOR NOTE
5, SHEET 1
DETAIL F1INTO MASONRY
EMBEDMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHOR
NOTE 3, SHEET 1
DETAIL F2INTO WOOD
1/4" MAX.1/4" MAX.
1/4" MAX.
1/4" MAX.
EMBEDMENT
EDGEDISTANCE
FRAMEHEIGHT
PANELHEIGHT
EXTERIOR
50
7
33
50
9
33
25
61 62
26
2
8
1
13
42 43 44 45
42
26
25
8
2-1/2" = TOTALSILL HEIGHT
.390.390
.390
.390
DLO WIDTH = NOM. PANEL WIDTH - 8-9/16"DLO HEIGHT = DOOR HEIGHT - 11-1/16"PANEL HEIGHT = DOOR HEIGHT - 2-1/2"
12
OR
OR
82
81
63
EDGEDISTANCE
CONCRETE/CMU PERANCHOR REQUIREMENT
TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A,SHEET 1 & NOTE 3,THIS SHEET
TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A,SHEET 1 & NOTE 3,THIS SHEET
(2-1/2" TOTALSILL HEIGHT)
(3-1/2" TOTALSILL HEIGHT)
(4-1/16" TOTALSILL HEIGHT)
(4-5/8" TOTALSILL HEIGHT)
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A, SHEET1 & NOTE 3, THIS SHEET TYP. ANCHOR TYPE, EMBEDMENT
AND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A, SHEET1 & NOTE 3, THIS SHEET
TYP. ANCHOR TYPE, EMBEDMENT ANDEDGE DISTANCE PER SUBSTRATE, SEETABLE A, SHEET 1 & NOTE 3, THIS SHEET
TYP. ANCHOR TYPE, EMBEDMENT ANDEDGE DISTANCE PER SUBSTRATE, SEETABLE A, SHEET 1 & NOTE 3, THIS SHEET
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEETS 11 & 12 FOR ANCHOR LOCATION & SPACING,FOR ANCHOR QUANTITIES, SEE TABLES 1 & 2.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED ATALL FRAME ANCHOR LOCATIONS.5) SEE SHEET 20 FOR SCREEN DETAILS.6) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.ALL REINFORCEMENTS ARE APPROXIMATELY THE FULLLENGTH OF THE EXTRUSION. REFER TO TEST REPORTS FOREXACT DIMENSIONS.
NTS 6 OF 25
9121
2221 91
2221
91
97 21.9"MAX. O.C.
35
OPT.
OPT. OPT.
SEE FIG 1,THIS SHEET
SEE FIG 1,THIS SHEET
SEE FIG 1,THIS SHEET
8
8 88
8
8
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
ANCHOR PLATE ATEVERY ANCHOR
LOCATION
8
22
SGD-5470 SGD-5470 SGD-5470
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
DETAIL G1135°
INSIDE CORNER
DETAIL H190°
INSIDE CORNER
DETAIL H290°
OUTSIDE CORNER
DETAIL G2135°
OUTSIDE CORNER
EXTERIOR
EXTERIOREXTERIOR
EXTERIOR
EXTERIOR
EXTERIOR
EXTERIOR
INTERIOR
INTERIOR
EXTERIOR
INTERIOR
INTERIOR
INTERIOR
INTERIOR
135°
135°90°
90°
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) SEE SHEETS 14 & 15 FOR ANCHOR LOCATION & SPACING, FOR ANCHORQUANTITIES, SEE TABLES 1 & 2.3) CORNER ASTRAGAL MAY BE EITHER TO THE INTERIOR OR EXTERIOR,DEPENDING ON CONFIGURATION.
CORNER ASTRAGAL HORIZ. X-SECT.
NTS 5 OF 25
J ROSOWSKI
237 96
3619
69
26
96
96
69
9635
38
19
19
69
96
40
39
94
41
9619 69
40
39
94
41
33
33
37
33
33
INTERIOR
INTERIOR
INTERIOR
1
1
2
2
1
2
1
OR25
26OR25
26OR25
26OR25
7171
INTERIOR POCKETS MUSTINCLUDE A NON-STRUCTURAL,FRAME JAMB TO REDUCE THE
POSSIBILITY OF WATERINFILTRATION.
OPTIONAL NON-STRUCTURAL
ANCHORS FORINTERIOR POCKET
JAMB
INTERIOR POCKET
CONCRETE/CMUPER ANCHORREQUIREMENT
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER
SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
J ROSOWSKIP-HOOK EXAMPLES, HORIZ. X-SECT.
EMBEDMENT
EDGEDISTANCE
METAL TYP., ANCHOR LENGTHTO BE A MIN. OF 3 THREADS
BEYOND THE METAL SUBSTRATE
1/4"MAX.
EDGEDISTANCE
CONCRETE/CMUPER ANCHORREQUIREMENT
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER
SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEET 13 FOR ANCHOR LOCATION & SPACING, FOR ANCHOR QUANTITIES, SEE TABLES 1 & 2.4) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.5) INTERIOR OR EXTERIOR POCKETS APPLICABLE FOR ALL INSTALLATION METHODS.6) POCKET WALL OR CAVITY IS NOT PART OF THIS APPROVAL AND IS TO BE DESIGNED BY OTHERSAND REVIEWED BY THE AUTHORITY HAVING JURISDICTION.
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A,SHEET 1 & NOTE 3, BELOW
EMBEDMENT
1/4" MAX.
EXTERIOR POCKET
EXTERIOR POCKETEXTERIOR POCKET
DETAIL I2INTO MASONRY
DETAIL I3INTO METAL
1/4" MAX.
EXTERIOR
POCKET BY OTHERS, SEENOTE 6 BELOW.
EDGEDISTANCE
EMBED-MENT
DETAIL I1INTO MASONRY
EXTERIOR
INTERIOR
OPT.ANCHOR
33
30
21
18 OPT.17
10
SEE FIG 1,THIS SHEET
2728 OR
OPT. ANCHOR
EDGEDISTANCE
EMBEDMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHORNOTE 3, SHEET 1
EXTERIOR
DETAIL I4INTO WOOD
17
82
31
2728 OR
26
31
2728 OR
1/4" MAX.
EXTERIOR
EXTERIOR
FOR DOOR HEIGHTS OVER 96"
FOR DOOR HEIGHTS 96" AND LESS:
30
10
31
OPT. ANCHOR
OPT.ANCHOR
17
17
30
10
FIGURE 1, INTERLOCKS AT POCKETS:
NTS 6 OF 25
9121
2221 91
2221
91
97 21.9"MAX. O.C.
35
OPT.
OPT. OPT.
SEE FIG 1,THIS SHEET
SEE FIG 1,THIS SHEET
SEE FIG 1,THIS SHEET
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
MAX 18.5" O.C.
22
SGD-5470 SGD-5470
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
MAX 3.5" O.C.SEE SHEET 19
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
INTERIOR POCKETS MUSTINCLUDE A NON-STRUCTURAL,FRAME JAMB TO REDUCE THE
POSSIBILITY OF WATERINFILTRATION.
OPTIONAL NON-STRUCTURAL
ANCHORS FORINTERIOR POCKET
JAMB
INTERIOR POCKET
CONCRETE/CMUPER ANCHORREQUIREMENT
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER
SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
J ROSOWSKIP-HOOK EXAMPLES, HORIZ. X-SECT.
EMBEDMENT
EDGEDISTANCE
METAL TYP., ANCHOR LENGTHTO BE A MIN. OF 3 THREADS
BEYOND THE METAL SUBSTRATE
1/4"MAX.
EDGEDISTANCE
CONCRETE/CMUPER ANCHORREQUIREMENT
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER
SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEET 13 FOR ANCHOR LOCATION & SPACING, FOR ANCHOR QUANTITIES, SEE TABLES 1 & 2.4) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.5) INTERIOR OR EXTERIOR POCKETS APPLICABLE FOR ALL INSTALLATION METHODS.6) POCKET WALL OR CAVITY IS NOT PART OF THIS APPROVAL AND IS TO BE DESIGNED BY OTHERSAND REVIEWED BY THE AUTHORITY HAVING JURISDICTION.
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A,SHEET 1 & NOTE 3, BELOW
EMBEDMENT
1/4" MAX.
EXTERIOR POCKET
EXTERIOR POCKETEXTERIOR POCKET
DETAIL I2INTO MASONRY
DETAIL I3INTO METAL
1/4" MAX.
EXTERIOR
POCKET BY OTHERS, SEENOTE 6 BELOW.
EDGEDISTANCE
EMBED-MENT
DETAIL I1INTO MASONRY
EXTERIOR
INTERIOR
OPT.ANCHOR
33
30
21
18 OPT.17
10
SEE FIG 1,THIS SHEET
2728 OR
OPT. ANCHOR
EDGEDISTANCE
EMBEDMENT
2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHORNOTE 3, SHEET 1
EXTERIOR
DETAIL I4INTO WOOD
17
82
31
2728 OR
26
31
2728 OR
1/4" MAX.
EXTERIOR
EXTERIOR
FOR DOOR HEIGHTS OVER 96"
FOR DOOR HEIGHTS 96" AND LESS:
30
10
31
OPT. ANCHOR
OPT.ANCHOR
17
17
30
10
FIGURE 1, INTERLOCKS AT POCKETS:
NTS 6 OF 25
9121
2221 91
2221
91
97 21.9"MAX. O.C.
OPT.
OPT. OPT.
SEE FIG 1,THIS SHEET
SEE FIG 1,THIS SHEET
SEE FIG 1,THIS SHEET
22
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
TABLE B1:
DP & ANCHOR QUANTITY TABLE
NTS 7 OF 25
J ROSOWSKI
Des
c.
Scal
e
Shee
t
DW
G
Serie
sTi
tle
No.
Rev
.
Dra
wn
By
Dat
e
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
Rev
AR
evB
Dat
eD
ate
Rev
AR
evB
No.
TABLE NOTES:
1) SEE SILL RISER TYPES ON SHEET 4.2) SHEET APPLIES TO 2, 3 AND 4 TRACK CONFIGURATIONS.3) REFER TO ANCHOR NOTES, SHEET 1.4) SEE SHEETS 11-16 FOR ANCHOR LOCATION & SPACING
DLO WIDTH = NOM. PANEL WIDTH - 8-9/16"DLO HEIGHT = DOOR HEIGHT - 11-1/16"PANEL HEIGHT = DOOR HEIGHT - 2-1/2"
TOTAL # OF ANCHORS THROUGH THE JAMB.
THE MAXIMUM DP AT THESE ANCHOR QUANTITIES.
ANCHORAGE TYPE PER SUBSTRATE REQUIRED TO ACHIEVE THE DESIGNPRESSURE, USING THE ANCHOR QUANTIES LISTED BELOW. SEE TABLE A,SHEET 1 FOR COMPLETE ANCHOR LIMITATIONS.
THE # OF ANCHORS REQUIRED THROUGH THE P-HOOK,PERPENDICULAR TO THE GLASS.
# OF ANCHORS THROUGH THE HEAD & SILL. (EX: FOR C3+1, 3 ANCHORSCLUSTERED AT PANEL MEETING POINT AND 1 ANCHOR REQUIRED ATMIDSPAN OF PANEL).
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
TABLE 1:
USED IN EXAMPLE ON SHEET 9
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
DLO WIDTH = NOM. PANEL WIDTH - 8-9/16"DLO HEIGHT = DOOR HEIGHT - 11-1/16"PANEL HEIGHT = DOOR HEIGHT - 2-1/2"
TOTAL # OF ANCHORS THROUGH THE JAMB.
THE MAXIMUM DP AT THESE ANCHOR QUANTITIES.
ANCHORAGE TYPE PER SUBSTRATE REQUIRED TO ACHIEVE THE DESIGNPRESSURE, USING THE ANCHOR QUANTIES LISTED BELOW. SEE TABLE A,SHEET 1 FOR COMPLETE ANCHOR LIMITATIONS.
DP & ANCHOR QUANTITY TABLE
NTS 8 OF 25
J ROSOWSKI
Des
c.
Scal
e
Shee
t
DW
G
Serie
sTi
tle
No.
Rev
.
Dra
wn
By
Dat
e
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
Rev
AR
evB
Dat
eD
ate
Rev
AR
evB
No.
TABLE NOTES:
1) SEE SILL RISER TYPES ON SHEET 4.2) SHEET APPLIES TO 2, 3 AND 4 TRACK CONFIGURATIONS.3) REFER TO ANCHOR NOTES, SHEET 1.4) SEE SHEETS 11-16 FOR ANCHOR LOCATION & SPACING
TABLE B2:
# OF ANCHORS THROUGH THE HEAD & SILL. (EX: FOR C3+1, 3 ANCHORSCLUSTERED AT PANEL MEETING POINT AND 1 ANCHOR REQUIRED ATMIDSPAN OF PANEL).
THE # OF ANCHORS REQUIRED THROUGH THE P-HOOK,PERPENDICULAR TO THE GLASS.
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
TABLE 2:
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
HEAD SPLICE
CENTERLINE
OF PANEL 2
CENTERLINE
OF INTERLOCK
CENTERLINE
OF PANEL 3
CENTERLINE
OF PANEL 1
CENTERLINE
OF INTERLOCK
"+2" ANCHORAGE,SHEET 12 "+2" ANCHORAGE,
SHEET 12"C3" CLUSTER,SHEET 12
"C3" CLUSTER,SHEET 12 END ANCHORAGE
(MIN. 1 ANCHOR)
3-PANEL, 3 TRACK, STRAIGHT CONFIGURATION - PXXX,INTERIOR MOUNT POCKET, 48" X 84" NOM. PANELS,LAMINATED, IG GLAZING, ANCHOR GROUP A IN WOOD SUBSTRATE,PROJECT DESIGN PRESSURE REQUIRED: +48.2/-58.6 PSF
JAMBANCHORAGE
DETAILS
EXTERIOR
6" MAX.
21.6"MAX.O.C.
P-HOOKANCHORAGE
DETAILS
"+2"ANCHORAGE,
SHEET 12
SEE POCKET JAMBINSTALLATION ONSHEET 6
FRAME JAMB REQUIRED@ INTERIOR POCKETS
HEAD ANCHORAGE DETAILS
1) KNOWING THE PRODUCT'S REQUIREMENTS, SCAN THROUGH TABLES 1 & 2FOR A DESIGN PRESSURE THAT MEETS OR EXCEEDS THE REQUIREMENT OF+48.2/-58.6 AT A NOM. PANEL SIZE OF 48" X 84". FROM TABLE 1, SHEET 7, THEDESIGN PRESSURE IS +60/-60 WHICH EXCEEDS THE PROJECT DESIGNPRESSURE REQUIREMENTS.
FOR WOOD INSTALLATION USING ANYANCHOR IN GROUP A (SEE TABLE A), TABLE1 SHOWS ANCHOR REQUIREMENTS OF:
2) ANCHOR LOCATION DETAILS, CAN BE FOUND ON:HEAD (CLUSTER ANCHORS): SHEET 12 FOR THE "C3" CLUSTER ANCHORS ATTHE INTERLOCK/ASTRAGAL.HEAD (INTERMEDIATE ANCHORS): SHEET 12 FOR THE "+2 ANCHORS AT THEMIDSPAN OF EACH PANEL.SILL (CLUSTER ANCHORS): SHEET 11 FOR THE "C3" CLUSTER ANCHORS ATTHE INTERLOCK/ASTRAGAL.SILL (INTERMEDIATE ANCHORS): SHEET 11 FOR THE "+2 ANCHORS AT THEMIDSPAN OF EACH PANEL.JAMB: 5 ANCHORS, SHEET 13 FOR GEN. LAYOUT.P-HOOK: 7 ANCHORS, SHEET 13 FOR GENERALLAYOUT.
3) INSTALLATION DETAILS INTO WOOD CANBE FOUND ON:HEAD & SILL: SHEET 4JAMB: SHEET 3P-HOOK: SHEET 6
STRAIGHT DOOR EXAMPLE
NTS 9 OF 25
J ROSOWSKI
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
6"MAX.
6"MAX.
SEE FIGURE BELOW FOR ADDITIONALANCHOR INFORMATION.
25-3/8" MAX.
EXTERIOR
INTERIOR
FOR SILL (SHOWN) AND HEAD, ANCHORS AT THEMIDPOINT OF END PANELS ARE ONLY REQUIRED IF THEO.C. DISTANCE TO THE NEXT ANCHOR CLUSTER IS OVER25-3/8", OTHERWISE ANCHORS ARE NOT REQUIRED ASPER THE FIGURE ABOVE:
DISTANCE TO NEXT CLUSTERTO BE 25-3/8" O.C. OR LESS
CENTERLINE OF END PANEL
GLAZING DETAILS
NTS
J ROSOWSKI
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600 10 OF 25
2-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
EXTERIOR EXTERIOR EXTERIOR
EXTERIOREXTERIOREXTERIOR
EXTERIOR EXTERIOR
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
2-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
2-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
3-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
3-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
4-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
4-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
SILL "+" INTERMEDIATE ANCHORS LAYOUT:
3-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
4" 4"
3.22"
4"
3.22"
4"
EXTERIOR
PANELCENTERLINE
4-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
3.22"
4"
EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C3"ANCHOR LOCATIONS
3-TRACK CLUSTER "C3"ANCHOR LOCATIONS
SILL CLUSTER ANCHORS LAYOUT:
FIGURES PERTAIN TO THE FOLLOWING SILLCLUSTER ANCHOR LOCATIONS:
4"
3.22"
4"
EXTERIOR
4-TRACK CLUSTER"C3" ANCHOR LOCATIONS
3.22"
4"
EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C5"ANCHOR LOCATIONS
3-TRACK CLUSTER "C5"ANCHOR LOCATIONS
4"
3.22"
4"
EXTERIOR
4-TRACK CLUSTER"C5" ANCHOR LOCATIONS
3.22"
4"
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
SILL SPLICE
CENTERLINE
OF PANEL 2
CENTERLINE
OF INTERLOCK
CENTERLINE
OF PANEL 3
CENTERLINE
OF PANEL 1
CENTERLINE
OF INTERLOCK
"+2" ANCHORAGE,SHEET 11 "+2" ANCHORAGE,
SHEET 11"C3" CLUSTER,SHEET 11
"C3" CLUSTER,SHEET 11 END ANCHORAGE
(MIN. 1 ANCHOR)
"+2"ANCHORAGE,
SHEET 11
SEE POCKET JAMBINSTALLATION ONSHEET 6
FRAME JAMBREQUIRED @INTERIOR POCKETS
SILL ANCHORAGE DETAILS
6"MAX.
6"MAX.
SEE FIGURE BELOW FOR ADDITIONALANCHOR INFORMATION.
25-3/8" MAX.
EXTERIOR
INTERIOR
FOR PRODUCT REFERENCES, ALSO SEE:A) SHEET 2 FOR ALLOWABLE CONFIGURATIONS AND EXACTLOCATIONS OF CROSS-SECTION DRAWINGS.B) SHEET 10 FOR SPECIFIC GLAZING TYPES.C) SHEET 17 FOR ALLOWABLE PANEL TYPES AND CALL NAMES.D) SHEETS 4 & 18 FOR EXTRUSION CROSS-SECTION DRAWINGS.E) SHEET 19 FOR INSTALLATION OF ADDITIONAL ACCESSORIES.F) SHEET 21 FOR A BILL OF MATERIALS.
12" MAX.
6" MAX.
6" MAX.
OPT. ANCHORTO AID IN
ALIGNMENT
OPT. ANCHORTO AID IN
ALIGNMENT
ANCHOR LOCATIONS A
NTS
J ROSOWSKI
11 OF 25
EXAMPLE:
SPLICE NOTE:NON-STRUCTURAL ANCHORS MAYBE ADDED IN-FIELD AS NEEDED TO
ALIGN THE HEAD OR SILL IF ASPLICE OCCURS WITHIN A POCKET.
FIGURES PERTAIN TO THE FOLLOWING SILLINTERMEDIATE ANCHOR LOCATIONS:NOTES:
1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL SILLS:
2.375"
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL SILLS:
2.375"XL EDGESPACER
DURASEALSPACER
SUPERSPACER NXT
7877
76
EXT. GLASS
BUTYL &DESICCANT
FOAM
STRUCTURALSILICONE
FOAMWITH
DESICCANT
ROLL-FORMEDSTAINLESS STEEL
INT. GLASS
ALUMINUMREINFORCEMENT POLYISO-
BUTYLENESEAL
SILICONE SEAL
EXT. GLASS
INT. GLASS
EXT. GLASS
INT. GLASS
DESICCANT FILL AREA
R TM
HOT-MELT BUTYL
R TM
5/16" NOM.
3/16" NOM.
5/16" NOM.
KODISPACE4SG TPS
75
STRUCTURALPOLYISOBUTYLENWITH DESICCANT
EXT. GLASS
INT. GLASS
SILICONE
1/4" NOM.
PXXX (3-TRACK)
PXXX (3-TRACK)
END PANEL ANCHOR EXCEPTION:
NOTES:1) BACKBEDDING SURFACES SHALL NOT BE PAINTED OR LAMINATED.2) PRODUCT MAY BE EITHER INTERIOR OR EXTERIOR GLAZED.
"T" = TEMPERED
3/16" T GLASS
3/16" T GLASS11/16" AIR SPACE
1-1/16" NOM.
GLASS DETAIL
7/8" NOM.GLASSBITE
86
79
PAINTED/LAMINATEDSURFACE83OR82
POCKET BYOTHERS, SEE
NOTE 6,SHEET 6
POCKET BYOTHERS, SEE
NOTE 6,SHEET 6
EXTERIOR INTERIOR
7877
7675
PRODUCT IS "EXTERIOR-GLAZED" IF #82-83 ISTOWARDS THE EXTERIOR.
EXTERIOR
PRODUCT IS "INTERIOR-GLAZED" IF #82-83 ISTOWARDS THE INTERIOR.
INTERIOR
SGD-5470SGD-5470SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
GLAZING DETAILS
NTS
J ROSOWSKI
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600 10 OF 25
2-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
EXTERIOR EXTERIOR EXTERIOR
EXTERIOREXTERIOREXTERIOR
EXTERIOR EXTERIOR
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
2-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
2-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
3-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
3-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
4-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
4-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
SILL "+" INTERMEDIATE ANCHORS LAYOUT:
3-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
4" 4"
3.22"
4"
3.22"
4"
EXTERIOR
PANELCENTERLINE
4-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
3.22"
4"
EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C3"ANCHOR LOCATIONS
3-TRACK CLUSTER "C3"ANCHOR LOCATIONS
SILL CLUSTER ANCHORS LAYOUT:
FIGURES PERTAIN TO THE FOLLOWING SILLCLUSTER ANCHOR LOCATIONS:
4"
3.22"
4"
EXTERIOR
4-TRACK CLUSTER"C3" ANCHOR LOCATIONS
3.22"
4"
EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C5"ANCHOR LOCATIONS
3-TRACK CLUSTER "C5"ANCHOR LOCATIONS
4"
3.22"
4"
EXTERIOR
4-TRACK CLUSTER"C5" ANCHOR LOCATIONS
3.22"
4"
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
ANCHOR LOCATIONS A
NTS
J ROSOWSKI
11 OF 25
FIGURES PERTAIN TO THE FOLLOWING SILLINTERMEDIATE ANCHOR LOCATIONS:NOTES:
1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL SILLS:
2.375"
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL SILLS:
2.375"XL EDGESPACER
DURASEALSPACER
SUPERSPACER NXT
7877
76
EXT. GLASS
BUTYL &DESICCANT
FOAM
STRUCTURALSILICONE
FOAMWITH
DESICCANT
ROLL-FORMEDSTAINLESS STEEL
INT. GLASS
ALUMINUMREINFORCEMENT POLYISO-
BUTYLENESEAL
SILICONE SEAL
EXT. GLASS
INT. GLASS
EXT. GLASS
INT. GLASS
DESICCANT FILL AREA
R TM
HOT-MELT BUTYL
R TM
5/16" NOM.
3/16" NOM.
5/16" NOM.
KODISPACE4SG TPS
75
STRUCTURALPOLYISOBUTYLENWITH DESICCANT
EXT. GLASS
INT. GLASS
SILICONE
1/4" NOM.
NOTES:1) BACKBEDDING SURFACES SHALL NOT BE PAINTED OR LAMINATED.2) PRODUCT MAY BE EITHER INTERIOR OR EXTERIOR GLAZED.
"T" = TEMPERED
3/16" T GLASS
3/16" T GLASS11/16" AIR SPACE
1-1/16" NOM.
GLASS DETAIL
7/8" NOM.GLASSBITE
86
79
PAINTED/LAMINATEDSURFACE83OR82
7877
7675
PRODUCT IS "EXTERIOR-GLAZED" IF #82-83 ISTOWARDS THE EXTERIOR.
EXTERIOR
PRODUCT IS "INTERIOR-GLAZED" IF #82-83 ISTOWARDS THE INTERIOR.
INTERIOR
SGD-5470SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
2-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
EXTERIOR EXTERIOR EXTERIOR
EXTERIOREXTERIOREXTERIOR
EXTERIOR EXTERIOR
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
2-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
2-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
3-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
3-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
4-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
4-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
SILL "+" INTERMEDIATE ANCHORS LAYOUT:
3-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
4" 4"
3.22"
4"
3.22"
4"
EXTERIOR
PANELCENTERLINE
4-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
3.22"
4"
EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C3"ANCHOR LOCATIONS
3-TRACK CLUSTER "C3"ANCHOR LOCATIONS
SILL CLUSTER ANCHORS LAYOUT:
FIGURES PERTAIN TO THE FOLLOWING SILLCLUSTER ANCHOR LOCATIONS:
4"
3.22"
4"
EXTERIOR
4-TRACK CLUSTER"C3" ANCHOR LOCATIONS
3.22"
4"
EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C5"ANCHOR LOCATIONS
3-TRACK CLUSTER "C5"ANCHOR LOCATIONS
4"
3.22"
4"
EXTERIOR
4-TRACK CLUSTER"C5" ANCHOR LOCATIONS
3.22"
4"
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
ANCHOR LOCATIONS A
NTS
J ROSOWSKI
11 OF 25
FIGURES PERTAIN TO THE FOLLOWING SILLINTERMEDIATE ANCHOR LOCATIONS:NOTES:
1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL SILLS:
2.375"
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL SILLS:
2.375"
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
EXTERIOR EXTERIOR EXTERIOR
EXTERIOREXTERIOREXTERIOR
EXTERIOR EXTERIOR
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
2-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
3-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
4-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
4-TRACK INTERMEDIATE "+2"ANCHOR LOCATIONS
HEAD "+" INTERMEDIATE ANCHORS LAYOUT:
3.22"
3.22"
4"
EXTERIOR
PANELCENTERLINE
4-TRACK INTERMEDIATE "+3"ANCHOR LOCATIONS
3.22"
4"
4"
3.22"
4"
4.75"
EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C3"ANCHOR LOCATIONS
3-TRACK CLUSTER "C3"ANCHOR LOCATIONS
HEAD CLUSTER ANCHORS LAYOUT:
3.22"
3.22"
4"
EXTERIOR
4-TRACK CLUSTER"C3"ANCHOR LOCATIONS
3.22"
4"
4"
EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C5"ANCHOR LOCATIONS
3-TRACK CLUSTER "C5"ANCHOR LOCATIONS
3.22"
3.22"
4"
EXTERIOR
4-TRACK CLUSTER"C5"ANCHOR LOCATIONS
3.22"
4"
4"
3-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
3-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
2-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
2-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
ANCHOR LOCATIONS B
NTS
J ROSOWSKI
12 OF 25
FIGURES PERTAIN TO THE FOLLOWING HEADCLUSTER ANCHOR LOCATIONS:
FIGURES PERTAIN TO THE FOLLOWING HEADINTERMEDIATE ANCHOR LOCATIONS:
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL HEADS:
2.375"
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL HEADS:
2.375"
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
4.81"
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
PO
CK
ET
PO
CK
ET
P-HOOK ANCHORS LAYOUT:
NOTES:1) SEE TABLES 1 & 2 FOR EXACT QUANTITYOF ANCHORS REQUIRED IN THE P-HOOK.
2-TRACK FRAMEJAMB ANCHORS
JAMB ANCHORS LAYOUT, (PARTIAL VIEW):
EXTERIOR
6"MAX.
EXTERIOR EXTERIOR
21.6"MAX.O.C.
6"MAX.
21.6"MAX.O.C.
6"MAX.
21.6"MAX.O.C.
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
(4) WEEP NOTCHESPER END @ 1" X .500"
(6) TRACK WEEP HOLESEVERY 24" @ 1.125" X .190";
(1) WEEP NOTCH EVERY24" @ 1.375" X .500"
(3) TRACK WEEP HOLESEVERY 24" @ 1.125" X .190";
(1) WEEP NOTCH EVERY24" @ 1.375" X .500"
(3) WEEP NOTCHESPER END @ 1" X .500"
(5) WEEP NOTCHESPER END @ 1" X .500"
JAMB
SILL
JAMB JAMB
SILLSILL
SILL WEEPHOLE LAYOUT (2, 3 & 4 TRACKS)
12"MAX.
6" MAX.
6"MAX.
OPT. ANCHORTO AID IN
ALIGNMENT
OPT. ANCHORTO AID IN
ALIGNMENT
(10) TRACK WEEP HOLESEVERY 24" @ 1.125" X .190";
(1) WEEP NOTCH EVERY24" @ 1.375" X .500"
EXTERIOREXTERIOR
EXTERIOR
ANCHOR LOCATIONS C
NTS
J ROSOWSKI
13 OF 25
FIGURES PERTAIN TO THE FOLLOWING POCKET JAMB(P-HOOK) ANCHOR LOCATIONS:
FIGURES PERTAIN TO THE FOLLOWING JAMB ANCHOR LOCATIONS:
3-TRACK FRAMEJAMB ANCHORS
4-TRACK FRAMEJAMB ANCHORS
NOTES:1) STANDARD ANCHOR LOCATIONS SHOWN.FOR 3 AND 4-TRACK JAMBS, ANCHORS MAYBE LOCATED IN ADJACENT TRACKS(SIMILAR TO THE 2-TRACK JAMB) ASREQUIRED TO MEET MIN. EDGE DISTANCECONSTRAINTS.
2.375" 4.75" 7.125"
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
2-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
HEAD 90° CORNER CLUSTER ANCHORS LAYOUT:
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
SILL 90° CORNER CLUSTER ANCHORS LAYOUT:
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
90°
90° ANCHOR LOCATIONS D
NTS
J ROSOWSKI
14 OF 25
4"4"
3.22"
4" 4"
3.22"
4"
4" 4" 4" 4"
4"
4"
4"
4"
3.22"3.22"
4"
4"
4"4"
3.22"
4"
4"
2-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
4"
2-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
2-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
4-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4"
4"
3.22"
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) DETAILS DEPICT ANCHOR QUANTITY AND SPACING, AND WOULD BESIMILAR FOR OUTSIDE (SHOWN) AND INSIDE CORNER CONFIGURATIONS.
3) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL HEADS AND SILLS:
2.375" 2.375"
FIGURES PERTAIN TO THEFOLLOWING 90° CORNER SILL
ANCHOR LOCATIONS:
FIGURES PERTAIN TO THE FOLLOWING 90° CORNERHEAD ANCHOR LOCATIONS:
SGD-5470
EXTERIOR4-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4"
3.22"
4"
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
HEAD 135° CORNER CLUSTER ANCHORS LAYOUT:
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
SILL 135° CORNER CLUSTER ANCHORS LAYOUT:
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) DETAILS DEPICT ANCHOR QUANTITY AND SPACING, AND WOULD BESIMILAR FOR OUTSIDE (SHOWN) AND INSIDE CORNER CONFIGURATIONS.
3) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL HEADS AND SILLS:
135°
135° ANCHOR LOCATIONS E
NTS
J ROSOWSKI
15 OF 25
4"
4"
4"
4" 4"
4"
4"
4"
4"
3.22"
4"
4"
4"
4"
4"
4"
3.22"
4"
4"
3.22"
4"2-TRACK 135° CORNER
"C4" ANCHOR LOCATIONS(USE WHERE "C3" IS SPECIFIED)
2-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
4-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
2-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
2-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
4-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3.22"
4"
4"
2.375" 2.375"
FIGURES PERTAIN TO THEFOLLOWING 135° CORNER SILL
ANCHOR LOCATIONS:
FIGURES PERTAIN TO THE FOLLOWING 135° CORNERHEAD ANCHOR LOCATIONS:
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
EXTERIOR EXTERIOR
EXTERIOREXTERIOR
EXTERIOR
SPLICELOCATION
SPLICELOCATION
SPLICELOCATION
SPLICELOCATION
SPLICELOCATION
SILL SPLICE ANCHORS LAYOUT @ INTERLOCK OR ASTRAGAL:
4"
4"
4"
3.22"
4"
EXTERIOR
SPLICELOCATION
3.22" 3.22"
4"
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) ABOVE FIGURES ARE FOR SPLICES OCCURRING AT THE ASTRAGAL OR INTERLOCK.FOR SPLICES OCCURRING INSIDE OF A POCKET, SEE THE EXAMPLE ON SHEET 9.
3) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL HEADS AND SILLS:
4) POCKET WALL OR CAVITY IS NOT PART OF THIS APPROVAL AND IS TO BE DESIGNEDBY OTHERS AND REVIEWED BY THE AUTHORITY HAVING JURISDICTION.
4"
EXTERIOR EXTERIOR
EXTERIOR
SPLICELOCATION
SPLICELOCATION
SPLICELOCATION
SPLICELOCATION
3.22"
3.22"
4"
4"
3.22"
4"
4.75"
2-TRACK SPLICE"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
4"
HEAD SPLICE ANCHORS LAYOUT @ INTERLOCK OR ASTRAGAL: FIGURES PERTAIN TO THE FOLLOWINGSPLICED SILL ANCHOR LOCATIONS:
2.375" 2.375"
FIGURES PERTAIN TO THE FOLLOWING SPLICEDHEAD ANCHOR LOCATIONS:
2-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK SPLICE"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
2-TRACK SPLICE"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
2-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK SPLICE"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4-TRACK SPLICE"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
4-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
EXTERIOR
ANCHOR LOCATIONS F
NTS
J ROSOWSKI
16 OF 25SGD-5470
EXTERIOR
SPLICELOCATION
EXTERIOR
SPLICELOCATION
3.22"
4"4.75"
4"4-TRACK SPLICE
"C4" ANCHOR LOCATIONS(USE WHERE "C3" IS SPECIFIED)
4-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
LEFT
STILE
RIGHT
STILEPANEL TYPE "F" SHOWN.
1) SEE DP/ANCHOR TABLES 1 & 2, SHEETS 7-8 FOR PANEL SIZES & DESIGN PRESSURE.
2) PANEL TYPES NOT SHOWN ARE NOT REQUIRED FOR ANY CONFIGURATIONS AND ARENOT AVAILABLE.
3) MAXIMUM NOMINAL PANEL WIDTH FOR ALL PANEL CONFIGURATIONS IS 60".
4) PANEL TYPE MAY BE EITHER EXTERIOR (STANDARD) OR INTERIOR GLAZED, BOTHTYPES QUALIFIED BY THIS APPROVAL, SEE DETAILS SHEET 10.
PANEL NOTES:
PANEL PANEL
PANEL TYPES
NTS
J ROSOWSKI
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600 17 OF 25
ANCHOR PLATE TRACK INSERT
INTERLOCK .300REINFORCEMENT,STANDARD
P-HOOK
ASTRAGALREINFORCEMENT
INTERLOCK .400REINFORCEMENT,HEAVY-DUTY
P-HOOK ADAPTOR
ASTRAGAL ADD-ONPANEL STILE, TOPAND BOTTOM RAIL
4 TRACK SILL2 TRACK HEAD/JAMB
2 TRACK SILL
FRAME SILLADD-ON
FRAME SCREWCOVER (PVC)
SILL TRACKCOVER
3 TRACK SILL
BOTTOM RAILSUPPORT
REINFORCEMENTPLATE
1 6
4
2
32 3326
17
87
3 TRACK HEAD/JAMB3
5
109
13
27 28 29 INTERLOCKADAPTER31
1211
24
18
TOP, BOTTOMAND STILEREINFORCEMENT
25
FIXED PANEL CLIP
(4) ANCHORTYPE AS USEDIN INSTALLATION,TABLE A, SHEET 1
FIXEDPANELCLIP
HEADERBLOCK
(3) #8 X1" SMS
(3) #10 X1.5" SMS
KEEPER
ALL PANEL CORNERSWELDED, NO ASSEMBLY
FASTENERS
#10 X1-1/2" SMS
BOTTOM RAILSUPPORT
(2) #10 X 1" SMSTHROUGH SUPPORT,
INTO PANEL
INTERLOCKREINF. PLATE
#8 X 1"SMS
JAMB TOSILL ASSEMBLY
INTERLOCK SILL RETAINERCLIP ATTACHMENT
HEADER BLOCK TO HEADATTACHMENT JAMB TO HEAD
ASSEMBLY
KEEPER TO JAMBATTACHMENT
PANELASSEMBLY
1) INSTALLCLIP INTO
PANELSTILE
2) INSTALL CLIPINTO FRAMEJAMB &SUBSTRATE, SEETABLE 1
INSTALL ONE BLOCK ATEACH INTERLOCK.
AT ASTRAGAL, INSTALLONE BLOCK THAT
SPANS BOTH PANELS.
INSTALL ONE ASSEMBLY AT EACH INTERLOCK
INSTALL ONE CLIP AT THEMIDSPAN OF EACH FIXED
PANEL-TO-FRAME JAMB LOCATION.
KEEPER
INTERIOR
EXTERIOR
(4) #10 X2" SMS
#10 X2-1/2" SMS
5.875
8.250
10.625
1.812
1.813
5.875
8.250
10.635
1.813
.540
.062.930
.125 .550
1.000
.062
.0621.435
1.613.060 2.060
1.983.060
.100
.080
.762
5.178
.100
.100
.100
.100
2.833
1.570
.110
1.595
2.768
.182.120
.300
1.595
2.768
.182.120
.400.312
.125
2.291
.1252.141
2.710
2.116.090
2.511
.080
4.635 4.279
1.875
.100
.301
.500
.949
.100
1.261 1.261
.210
1-1/16"OGEE BEAD
1-1/16"BEVELED BEAD82 83
.252
TOP, BOTTOMAND STILECOMPOSITEREINFORCEMENT
.3091.625
2.368
.188
#8 X1-1/4" SMS
REINFORCEMENT PLATE
REINF. BAR
BAR COVER
4-PANEL, 2-TRACKOXXX SHOWN
LOCKING JAMB
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) SEE SHEETS 11-16 FOR ANCHOR LOCATION & SPACING.3) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED AT ALL FRAME ANCHOR LOCATIONS.
2.975
FIXED PANEL CLIP23
.075.626
KEEPER20
.540
.062.500
.540
.062EXTENDEDKEEPER
19
4 TRACK HEAD/JAMB
2.696
.100
.0702.210
.229
.046
3.713.060
1.170
.291
1.928
.061
3.345
3.345
.065
.919
.919
.060
3.452
3.209
.300
.125
2.175
1.472
.125
.070
3.326
3.247
.090
INTERLOCK CAP,EXTENDED POCKET
REINFORCEMENTBAR
REINFORCEMENTBAR COVER 2221
3.0002.607
.229.061.291
135° CORNERASTRAGAL35 36 37 38 39 40 41
NOTES:
1) SEE SHEET 4 FORSILL RISERS.
2) SEE SHEET 20FOR SCREEN PARTS.
3) ALL DIMENSIONSIN INCHES.
EXTENDED POCKETINTERLOCK ADAPTER30
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
INSIDE 90°ASTRAGALRECEIVER
FIXEDSTILE
FIXEDSTILE
ASTRAGALBOX OUT
ASTRAGALBOX IN
ASTRAGALBOX IN
SINGLEINTERLOCK
IN
SINGLEINTERLOCK
OUT
SINGLEINTERLOCK
OUT
LOCKSTILEW/ HANDLE
ASTRAGALBOX OUT
SINGLEINTERLOCK
IN
LOCKSTILEW/ HANDLE
OUTSIDE 90°ASTRAGALRECEIVER
PANELTYPES OUTSIDE 135°
ASTRAGALRECEIVER
INSIDE 135°ASTRAGALRECEIVER
IN. 90°ASTRAGALRECEIVER
OUT. 90°ASTRAGALRECEIVER
OUT. 135°ASTRAGALRECEIVER
IN. 135°ASTRAGALRECEIVER
INTERIOR OREXTERIOR GLAZED
EXTRUSIONS
NTS
J ROSOWSKI
18 OF 25
ACCESSORIES INSTALLATION
NTS
J ROSOWSKI
19 OF 25
PARTS LIST
NTS
J ROSOWSKI
21 OF 25
TABLE C:
1.406
INTERIOR JAMB COVER34
2.838
2.073 .099
135° CORNERPASSIVE MOUNT
135° CORNERASTRAGAL CAP,EXTERIOR
135° CORNERASTRAGAL CAP,INTERIOR
90° CORNERASTRAGAL
90° CORNERASTRAGAL CAP,EXTERIOR
90° CORNERASTRAGAL CAP,INTERIOR
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
.100.329
93
94
24
92
11
INTERLOCKCLIP COVER
60
21
22
91
90
64
90
96
19
19
96
9523
93
1.500
.075
NOTES:1) ITEMS # 14-16, 46-49, 53-59, 72-74, 80, 81, 84, 85, 87-89, 98 & 99 ARE NOTUSED AND ARE NOT PART OF THIS APPROVAL.A. LYNN MILLER, P.E.
P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
107
114
101
108
111
100
SCREENSIDE RAIL,LATCH
SCREENFRAMERAIL
SCREEN OXOASTRAGALADAPTER
1.202
.935
1.081 1.081
1.7781.778
.050.050
BOX SCREENBOTTOM RAIL
BOX SCREENTOP RAIL
BOXSCREENSNAP-ONBUG FLAP
BOX SCREENSIDE RAIL
BOX SCREENASTRAGALADAPTER
FRAME SILLSCREENADD-ON
BOX SCREENSILL ADD-ON
BOX SCREEN HEADAND JAMB ADD-ON
1.487.055
1.510
1.487
.060
SCREEN VINYLASTRAGALADAPTER
1.993
.875
.062
1.993
.875
.062
1.874
1.020
.062
1.3431.306
.050
.055
1.593
.372
.725
.765.040
BOX SCREEN DETAILS: STANDARD SCREEN DETAILS:
.252 .231
106 103
108
33
118
119
115
111
116
117
115
102
2
131
120
112
104
125121
133123
130
129132
32
122
121
127
120
100 101 102
106
104
107 108
120 121 122
123 124
1.872
1.020
.062BOXSCREENINTERLOCK
103
1.833
1.373
.063
BOX SCREENOXOASTRAGALADAPTER
105
102
1.435
.782
.062
OR 4 OR 6
1 OR 3 OR 5
OR OR
OR OR
1 3 5
1 3 5
113 OR
102
PA
NE
L'S
LE
FT S
TILE
TY
PE
PANEL'S RIGHT STILE TYPE OR OR1 3 5
1 OR 3 OR 5
2 OR 4 OR 6
124
128OR
HORIZONTAL SECTIONEXAMPLE
HORIZONTAL SECTIONEXAMPLE
HORIZONTAL SECTION EXAMPLE
HORIZONTAL SECTION EXAMPLE
VERTICAL SECTIONEXAMPLE
VERTICAL SECTIONEXAMPLE
.045
SCREEN DETAILS
NTS
J ROSOWSKI
20 OF 25
111
TABLE D: BOX SCREEN
TABLE E: STANDARD SCREEN
DOUBLEINTERLOCK ASTRAGAL
LOCKSTILE
ASTRAGAL
SINGLEINTERLOCK
DOUBLEINTERLOCK LOCKSTILE
ASTRAGAL LOCKSTILE
DOUBLEINTERLOCK
DOUBLEINTERLOCK
DOUBLEINTERLOCK
LOCKSTILE
SINGLEINTERLOCK
SCREEN PANEL TYPES
NOTES:1) ALL DIMENSIONS IN INCHES.
3.483
1.681
1.681
1.681
2.025
.094
(4) #10X 2" SMS
(2) 1/4"X 2-1/4" SMS
ATTACH WITH #8 X 1-1/4"@ 34-1/2" MAX O.C.
SGD-5470SGD-5470SGD-5470SGD-5470SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
ANCHOR PLATE TRACK INSERT
INTERLOCK .300REINFORCEMENT,STANDARD
P-HOOK
ASTRAGALREINFORCEMENT
INTERLOCK .400REINFORCEMENT,HEAVY-DUTY
P-HOOK ADAPTOR
ASTRAGAL ADD-ONPANEL STILE, TOPAND BOTTOM RAIL
4 TRACK SILL2 TRACK HEAD/JAMB
2 TRACK SILL
FRAME SILLADD-ON
FRAME SCREWCOVER (PVC)
SILL TRACKCOVER
3 TRACK SILL
BOTTOM RAILSUPPORT
REINFORCEMENTPLATE
1 6
4
2
32 3326
17
87
3 TRACK HEAD/JAMB3
5
109
13
27 28 29 INTERLOCKADAPTER31
1211
24
18
TOP, BOTTOMAND STILEREINFORCEMENT
25
FIXED PANEL CLIP
(4) ANCHORTYPE AS USEDIN INSTALLATION,TABLE A, SHEET 1
FIXEDPANELCLIP
HEADERBLOCK
(3) #8 X1" SMS
(3) #10 X1.5" SMS
KEEPER
ALL PANEL CORNERSWELDED, NO ASSEMBLY
FASTENERS
#10 X1-1/2" SMS
BOTTOM RAILSUPPORT
(2) #10 X 1" SMSTHROUGH SUPPORT,
INTO PANEL
INTERLOCKREINF. PLATE
#8 X 1"SMS
JAMB TOSILL ASSEMBLY
INTERLOCK SILL RETAINERCLIP ATTACHMENT
HEADER BLOCK TO HEADATTACHMENT JAMB TO HEAD
ASSEMBLY
KEEPER TO JAMBATTACHMENT
PANELASSEMBLY
1) INSTALLCLIP INTO
PANELSTILE
2) INSTALL CLIPINTO FRAMEJAMB &SUBSTRATE, SEETABLE 1
INSTALL ONE BLOCK ATEACH INTERLOCK.
AT ASTRAGAL, INSTALLONE BLOCK THAT
SPANS BOTH PANELS.
INSTALL ONE ASSEMBLY AT EACH INTERLOCK
INSTALL ONE CLIP AT THEMIDSPAN OF EACH FIXED
PANEL-TO-FRAME JAMB LOCATION.
KEEPER
INTERIOR
EXTERIOR
(4) #10 X2" SMS
#10 X2-1/2" SMS
5.875
8.250
10.625
1.812
1.813
5.875
8.250
10.635
1.813
.540
.062.930
.125 .550
1.000
.062
.0621.435
1.613.060 2.060
1.983.060
.100
.080
.762
5.178
.100
.100
.100
.100
2.833
1.570
.110
1.595
2.768
.182.120
.300
1.595
2.768
.182.120
.400.312
.125
2.291
.1252.141
2.710
2.116.090
2.511
.080
4.635 4.279
1.875
.100
.301
.500
.949
.100
1.261 1.261
.210
1-1/16"OGEE BEAD
1-1/16"BEVELED BEAD82 83
.252
TOP, BOTTOMAND STILECOMPOSITEREINFORCEMENT
.3091.625
2.368
.188
#8 X1-1/4" SMS
REINFORCEMENT PLATE
REINF. BAR
BAR COVER
4-PANEL, 2-TRACKOXXX SHOWN
LOCKING JAMB
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) SEE SHEETS 11-16 FOR ANCHOR LOCATION & SPACING.3) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED AT ALL FRAME ANCHOR LOCATIONS.
2.975
FIXED PANEL CLIP23
.075.626
KEEPER20
.540
.062.500
.540
.062EXTENDEDKEEPER
19
4 TRACK HEAD/JAMB
2.696
.100
.0702.210
.229
.046
3.713.060
1.170
.291
1.928
.061
3.345
3.345
.065
.919
.919
.060
3.452
3.209
.300
.125
2.175
1.472
.125
.070
3.326
3.247
.090
INTERLOCK CAP,EXTENDED POCKET
REINFORCEMENTBAR
REINFORCEMENTBAR COVER 2221
3.0002.607
.229.061.291
135° CORNERASTRAGAL35 36 37 38 39 40 41
NOTES:
1) SEE SHEET 4 FORSILL RISERS.
2) SEE SHEET 20FOR SCREEN PARTS.
3) ALL DIMENSIONSIN INCHES.
EXTENDED POCKETINTERLOCK ADAPTER30
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
EXTRUSIONS
NTS
J ROSOWSKI
18 OF 25
ACCESSORIES INSTALLATION
NTS
J ROSOWSKI
19 OF 25
PARTS LIST
NTS
J ROSOWSKI
21 OF 25
TABLE C:
1.406
INTERIOR JAMB COVER34
2.838
2.073 .099
135° CORNERPASSIVE MOUNT
135° CORNERASTRAGAL CAP,EXTERIOR
135° CORNERASTRAGAL CAP,INTERIOR
90° CORNERASTRAGAL
90° CORNERASTRAGAL CAP,EXTERIOR
90° CORNERASTRAGAL CAP,INTERIOR
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
.100.329
93
94
24
92
11
INTERLOCKCLIP COVER
60
21
22
91
90
64
90
96
19
19
96
9523
93
1.500
.075
NOTES:1) ITEMS # 14-16, 46-49, 53-59, 72-74, 80, 81, 84, 85, 87-89, 98 & 99 ARE NOTUSED AND ARE NOT PART OF THIS APPROVAL.A. LYNN MILLER, P.E.
P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
107
114
101
108
111
100
SCREENSIDE RAIL,LATCH
SCREENFRAMERAIL
SCREEN OXOASTRAGALADAPTER
1.202
.935
1.081 1.081
1.7781.778
.050.050
BOX SCREENBOTTOM RAIL
BOX SCREENTOP RAIL
BOXSCREENSNAP-ONBUG FLAP
BOX SCREENSIDE RAIL
BOX SCREENASTRAGALADAPTER
FRAME SILLSCREENADD-ON
BOX SCREENSILL ADD-ON
BOX SCREEN HEADAND JAMB ADD-ON
1.487.055
1.510
1.487
.060
SCREEN VINYLASTRAGALADAPTER
1.993
.875
.062
1.993
.875
.062
1.874
1.020
.062
1.3431.306
.050
.055
1.593
.372
.725
.765.040
BOX SCREEN DETAILS: STANDARD SCREEN DETAILS:
.252 .231
106 103
108
33
118
119
115
111
116
117
115
102
2
131
120
112
104
125121
133123
130
129132
32
122
121
127
120
100 101 102
106
104
107 108
120 121 122
123 124
1.872
1.020
.062BOXSCREENINTERLOCK
103
1.833
1.373
.063
BOX SCREENOXOASTRAGALADAPTER
105
102
1.435
.782
.062
OR 4 OR 6
1 OR 3 OR 5
OR OR
OR OR
1 3 5
1 3 5
113 OR
102
OR OR1 3 5
1 OR 3 OR 5
2 OR 4 OR 6
124
128OR
HORIZONTAL SECTIONEXAMPLE
HORIZONTAL SECTIONEXAMPLE
HORIZONTAL SECTION EXAMPLE
HORIZONTAL SECTION EXAMPLE
VERTICAL SECTIONEXAMPLE
VERTICAL SECTIONEXAMPLE
.045
SCREEN DETAILS
NTS
J ROSOWSKI
20 OF 25
111
TABLE D: BOX SCREEN
TABLE E: STANDARD SCREEN
NOTES:1) ALL DIMENSIONS IN INCHES.
3.483
1.681
1.681
1.681
2.025
.094
(4) #10X 2" SMS
(2) 1/4"X 2-1/4" SMS
ATTACH WITH #8 X 1-1/4"@ 34-1/2" MAX O.C.
SGD-5470SGD-5470SGD-5470SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
FIXED PANEL CLIP
(4) ANCHORTYPE AS USEDIN INSTALLATION,TABLE A, SHEET 1
FIXEDPANELCLIP
HEADERBLOCK
(3) #8 X1" SMS
(3) #10 X1.5" SMS
KEEPER
ALL PANEL CORNERSWELDED, NO ASSEMBLY
FASTENERS
#10 X1-1/2" SMS
BOTTOM RAILSUPPORT
(2) #10 X 1" SMSTHROUGH SUPPORT,
INTO PANEL
INTERLOCKREINF. PLATE
#8 X 1"SMS
JAMB TOSILL ASSEMBLY
INTERLOCK SILL RETAINERCLIP ATTACHMENT
HEADER BLOCK TO HEADATTACHMENT JAMB TO HEAD
ASSEMBLY
KEEPER TO JAMBATTACHMENT
PANELASSEMBLY
1) INSTALLCLIP INTO
PANELSTILE
2) INSTALL CLIPINTO FRAMEJAMB &SUBSTRATE, SEETABLE 1
INSTALL ONE BLOCK ATEACH INTERLOCK.
AT ASTRAGAL, INSTALLONE BLOCK THAT
SPANS BOTH PANELS.
INSTALL ONE ASSEMBLY AT EACH INTERLOCK
INSTALL ONE CLIP AT THEMIDSPAN OF EACH FIXED
PANEL-TO-FRAME JAMB LOCATION.
KEEPER
INTERIOR
EXTERIOR
(4) #10 X2" SMS
#10 X2-1/2" SMS
#8 X1-1/4" SMS
REINFORCEMENT PLATE
REINF. BAR
BAR COVER
4-PANEL, 2-TRACKOXXX SHOWN
LOCKING JAMB
NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) SEE SHEETS 11-16 FOR ANCHOR LOCATION & SPACING.3) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED AT ALL FRAME ANCHOR LOCATIONS.
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
ACCESSORIES INSTALLATION
NTS
J ROSOWSKI
19 OF 25
PARTS LIST
NTS
J ROSOWSKI
21 OF 25
TABLE C:
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
93
94
24
92
11
INTERLOCKCLIP COVER
60
21
22
91
90
64
90
96
19
19
96
9523
93
NOTES:1) ITEMS # 14-16, 46-49, 53-59, 72-74, 80, 81, 84, 85, 87-89, 98 & 99 ARE NOTUSED AND ARE NOT PART OF THIS APPROVAL.A. LYNN MILLER, P.E.
P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
107
114
101
108
111
100
SCREENSIDE RAIL,LATCH
SCREENFRAMERAIL
SCREEN OXOASTRAGALADAPTER
1.202
.935
1.081 1.081
1.7781.778
.050.050
BOX SCREENBOTTOM RAIL
BOX SCREENTOP RAIL
BOXSCREENSNAP-ONBUG FLAP
BOX SCREENSIDE RAIL
BOX SCREENASTRAGALADAPTER
FRAME SILLSCREENADD-ON
BOX SCREENSILL ADD-ON
BOX SCREEN HEADAND JAMB ADD-ON
1.487.055
1.510
1.487
.060
SCREEN VINYLASTRAGALADAPTER
1.993
.875
.062
1.993
.875
.062
1.874
1.020
.062
1.3431.306
.050
.055
1.593
.372
.725
.765.040
BOX SCREEN DETAILS: STANDARD SCREEN DETAILS:
106 103
108
33
118
119
115
111
116
117
115
102
2
131
120
112
104
125121
133123
130
129132
32
122
121
127
120
100 101 102
106
104
107 108
120 121 122
123 124
1.872
1.020
.062BOXSCREENINTERLOCK
103
1.833
1.373
.063
BOX SCREENOXOASTRAGALADAPTER
105
102
1.435
.782
.062
OR 4 OR 6
1 OR 3 OR 5
OR OR
OR OR
1 3 5
1 3 5
113 OR
102
OR OR1 3 5
1 OR 3 OR 5
2 OR 4 OR 6
124
128OR
HORIZONTAL SECTIONEXAMPLE
HORIZONTAL SECTIONEXAMPLE
HORIZONTAL SECTION EXAMPLE
HORIZONTAL SECTION EXAMPLE
VERTICAL SECTIONEXAMPLE
VERTICAL SECTIONEXAMPLE
.045
SCREEN DETAILS
NTS
J ROSOWSKI
20 OF 25
111
TABLE D: BOX SCREEN
TABLE E: STANDARD SCREEN
NOTES:1) ALL DIMENSIONS IN INCHES.
(4) #10X 2" SMS
(2) 1/4"X 2-1/4" SMS
ATTACH WITH #8 X 1-1/4"@ 34-1/2" MAX O.C.
SGD-5470SGD-5470SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
PARTS LIST
NTS
J ROSOWSKI
21 OF 25
TABLE C:
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
NOTES:1) ITEMS # 14-16, 46-49, 53-59, 72-74, 80, 81, 84, 85, 87-89, 98 & 99 ARE NOTUSED AND ARE NOT PART OF THIS APPROVAL.
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
107
114
101
108
111
100
SCREENSIDE RAIL,LATCH
SCREENFRAMERAIL
SCREEN OXOASTRAGALADAPTER
1.202
.935
1.081 1.081
1.7781.778
.050.050
BOX SCREENBOTTOM RAIL
BOX SCREENTOP RAIL
BOXSCREENSNAP-ONBUG FLAP
BOX SCREENSIDE RAIL
BOX SCREENASTRAGALADAPTER
FRAME SILLSCREENADD-ON
BOX SCREENSILL ADD-ON
BOX SCREEN HEADAND JAMB ADD-ON
1.487.055
1.510
1.487
.060
SCREEN VINYLASTRAGALADAPTER
1.993
.875
.062
1.993
.875
.062
1.874
1.020
.062
1.3431.306
.050
.055
1.593
.372
.725
.765.040
BOX SCREEN DETAILS: STANDARD SCREEN DETAILS:
106 103
108
33
118
119
115
111
116
117
115
102
2
131
120
112
104
125121
133123
130
129132
32
122
121
127
120
100 101 102
106
104
107 108
120 121 122
123 124
1.872
1.020
.062BOXSCREENINTERLOCK
103
1.833
1.373
.063
BOX SCREENOXOASTRAGALADAPTER
105
102
1.435
.782
.062
OR 4 OR 6
1 OR 3 OR 5
OR OR
OR OR
1 3 5
1 3 5
113 OR
102
OR OR1 3 5
1 OR 3 OR 5
2 OR 4 OR 6
124
128OR
HORIZONTAL SECTIONEXAMPLE
HORIZONTAL SECTIONEXAMPLE
HORIZONTAL SECTION EXAMPLE
HORIZONTAL SECTION EXAMPLE
VERTICAL SECTIONEXAMPLE
VERTICAL SECTIONEXAMPLE
.045
SCREEN DETAILS
NTS
J ROSOWSKI
20 OF 25
111
TABLE D: BOX SCREEN
TABLE E: STANDARD SCREEN
NOTES:1) ALL DIMENSIONS IN INCHES.
SGD-5470SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16 VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
PARTS LIST
NTS
J ROSOWSKI
21 OF 25
TABLE C:
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
NOTES:1) ITEMS # 14-16, 46-49, 53-59, 72-74, 80, 81, 84, 85, 87-89, 98 & 99 ARE NOTUSED AND ARE NOT PART OF THIS APPROVAL.
TABLE D: BOX SCREEN
TABLE E: STANDARD SCREEN
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
EXTERIOR EXTERIOR EXTERIOR
EXTERIOREXTERIOREXTERIOR
EXTERIOR EXTERIOR
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
2-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
3-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
4-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
4-TRACK INTERMEDIATE "+2"ANCHOR LOCATIONS
HEAD "+" INTERMEDIATE ANCHORS LAYOUT (USING FRAME FIN ADDON):
4"
3.22"
4"
EXTERIOR
PANELCENTERLINE
4-TRACK INTERMEDIATE "+3"ANCHOR LOCATIONS
3.22"
4"
4"EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C3"ANCHOR LOCATIONS
3-TRACK CLUSTER "C3"ANCHOR LOCATIONS
HEAD CLUSTER ANCHORS LAYOUT (USING FRAME FIN ADDON):
4"
3.22"
EXTERIOR
4-TRACK CLUSTER"C3"ANCHOR LOCATIONS
3.22"
4"
EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C5"ANCHOR LOCATIONS
3-TRACK CLUSTER "C5"ANCHOR LOCATIONS
4"
3.22"
4"
EXTERIOR
4-TRACK CLUSTER"C5"ANCHOR LOCATIONS
3.22"
4"
3-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
3-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
2-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
2-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
2-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
HEAD 135° CORNER CLUSTER ANCHORS LAYOUT (USING FRAME FIN ADDON):HEAD 90° CORNER CLUSTER ANCHORS LAYOUT (USING FRAME FIN ADDON):
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
135°
90° ANCHOR LOCATIONS C
NTS
ANCHOR LOCATIONS B
NTS
FIGURES PERTAIN TO THE FOLLOWING HEADCLUSTER ANCHOR LOCATIONS:
FIGURES PERTAIN TO THE FOLLOWING HEADINTERMEDIATE ANCHOR LOCATIONS:
4"
4"
4"
4" 4"
4"
4"
2-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
2-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
2-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
4-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) DETAILS DEPICT ANCHOR QUANTITY AND SPACING, AND WOULD BESIMILAR FOR OUTSIDE (SHOWN) AND INSIDE CORNER CONFIGURATIONS.
3) TRACK-TO-TRACKDISTANCE IS 2.375": 2.375"
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375": 2.375"
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL HEADS:
2.375"
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) ABOVE FIGURES ARE FOR SPLICES OCCURRING AT THE ASTRAGAL OR INTERLOCK.FOR SPLICES OCCURRING INSIDE OF A POCKET, SEE THE EXAMPLE ON SHEET 9.
3) TRACK-TO-TRACKDISTANCE IS 2.375":
EXTERIOR EXTERIOR
EXTERIOR
SPLICELOCATION
SPLICELOCATION
SPLICELOCATION
SPLICELOCATION
4"4"2-TRACK SPLICE
"C4" ANCHOR LOCATIONS(USE WHERE "C3" IS SPECIFIED)
HEAD SPLICE ANCHORS LAYOUT @ INTERLOCK OR ASTRAGAL (USING FRAME FIN ADDON):
2.375"
FIGURES PERTAIN TO THE FOLLOWING SPLICEDHEAD ANCHOR LOCATIONS:
2-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK SPLICE"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
A. LYNN MILLER, P.E.P.E.# 106954
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
EXTERIOR
ANCHOR LOCATIONS D
NTS
FIGURES PERTAIN TO THEFOLLOWING 135° CORNER
HEAD ANCHOR LOCATIONS:
FIGURES PERTAIN TO THE FOLLOWING 90° CORNERHEAD ANCHOR LOCATIONS:
EXTERIOR
SPLICELOCATION
EXTERIOR
SPLICELOCATION
3.22"
4"4.75"
4"4-TRACK SPLICE
"C4" ANCHOR LOCATIONS(USE WHERE "C3" IS SPECIFIED)
4-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
EXTERIOR4-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4"
3.22"
4"
2-TRACK FRAMEJAMB ANCHORS
EXTERIOR
6"MAX.
EXTERIOR EXTERIOR
21.6"MAX.O.C.
6"MAX.
21.6"MAX.O.C.
6"MAX.
21.6"MAX.O.C.
FIGURES PERTAIN TO THE FOLLOWING JAMB ANCHOR LOCATIONS:
3-TRACK FRAMEJAMB ANCHORS
4-TRACK FRAMEJAMB ANCHORS
NOTES:1) STANDARD ANCHORLOCATIONS SHOWN. FOR 3 AND4-TRACK JAMBS, ANCHORS INTHE INTERIOR TRACK MAY BELOCATED IN THE ADJACENTTRACK AS REQUIRED TO MEETMIN. EDGE DISTANCECONSTRAINTS FROM THEINTERIOR.
2.375"
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600 NTS
ANCHORAGE DETAILS FOR SLIDING GLASS DOORS WHEN INSTALLED WITH FRAME FIN ADDON @ HEAD AND JAMB (SHEETS 22-25)
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
TO ACHIEVE PROPER ANCHOREDGE DISTANCE, THE
FOLLOWING SHEETS (22-25)SHOW ANCHOR PATTERNSTHAT MUST BE USED WHEN
USING THE FRAME FIN ADDON.
4"
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
EU
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
U
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
EU
N
C
H
A
N
G
E
D
F
R
O
M
B
O
X
F
R
A
M
E
3.22"
4"
4"
2" 2"
3.22"
4"
NOTES
1) DETAILS APPLY TO 2, 3AND 4 TRACKCONFIGURATIONS.
2) REFER TO TABLE AFOR ANCHORCONSTRAINTS.
3) SILL ANCHORAGEWITH FIN ADDON ISUNCHANGED FROM THEBOX FRAMEANCHORAGE.
4"
3.22"
4"
3.22"3.22"
4"
4"
3.22"
4"
4"
4"4"4"
4"4"
4"
3.22"
4.75"
ANCHOR LOCATIONS A
EDGEDISTANCE
EMBEDMENT
1/4" MAX.
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A, SHEET 1.
8
99
EXTERIOR
1/4" MAX.
EDGEDISTANCE
EMBEDMENT
SUBSTRATE
8
99
2-TRACK FRAMEJAMB ANCHORAGE DETAIL
EXTERIOR
TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A,SHEET 1.
SUBSTRATE
2-TRACK FRAMEHEAD ANCHORAGE DETAIL
EMBEDMENT
1/4" MAX.
EDGEDISTANCE
EXTERIOR
2-TRACK FRAMESILL ANCHORAGE DETAIL
SUBSTRATE
TYP. ANCHOR TYPE,EMBEDMENT AND EDGEDISTANCE PER SUBSTRATE,SEE TABLE A, SHEET 1.
DETA2
DETE3
DETF3
J ROSOWSKI
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
J ROSOWSKI
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
J ROSOWSKI
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
J ROSOWSKI
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
1.625
.875
.125
FRAME FIN-ADDONALUMINUM 6063-T6PART # 19033
99
24 OF 2523 OF 25 25 OF 2522 OF 25
JAMB ANCHORS LAYOUT (USING FRAME FIN ADDON):
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
EXTERIOR EXTERIOR EXTERIOR
EXTERIOREXTERIOREXTERIOR
EXTERIOR EXTERIOR
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
PANELCENTERLINE
2-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
3-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
4-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
4-TRACK INTERMEDIATE "+2"ANCHOR LOCATIONS
HEAD "+" INTERMEDIATE ANCHORS LAYOUT (USING FRAME FIN ADDON):
4"
3.22"
4"
EXTERIOR
PANELCENTERLINE
4-TRACK INTERMEDIATE "+3"ANCHOR LOCATIONS
3.22"
4"
4"EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C3"ANCHOR LOCATIONS
3-TRACK CLUSTER "C3"ANCHOR LOCATIONS
HEAD CLUSTER ANCHORS LAYOUT (USING FRAME FIN ADDON):
4"
3.22"
EXTERIOR
4-TRACK CLUSTER"C3"ANCHOR LOCATIONS
3.22"
4"
EXTERIOR
EXTERIOR
2-TRACK CLUSTER "C5"ANCHOR LOCATIONS
3-TRACK CLUSTER "C5"ANCHOR LOCATIONS
4"
3.22"
4"
EXTERIOR
4-TRACK CLUSTER"C5"ANCHOR LOCATIONS
3.22"
4"
3-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
3-TRACK INTERMEDIATE"+3" ANCHOR LOCATIONS
2-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS
2-TRACK INTERMEDIATE"+1" ANCHOR LOCATION
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
ASTRAGAL ORINTERLOCK
CENTERLINE
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
ANCHOR LOCATIONS B
NTS
FIGURES PERTAIN TO THE FOLLOWING HEADCLUSTER ANCHOR LOCATIONS:
FIGURES PERTAIN TO THE FOLLOWING HEADINTERMEDIATE ANCHOR LOCATIONS:
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375": 2.375"
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL HEADS:
2.375"
UNCHANGED
FROM BOX
FRAME
4"
UNCHANGED
FROM BOX
FRAME
UNCHANGED
FROM BOX
FRAME
UNCHANGED
FROM BOX
FRAME
UNCHANGED
FROM BOX
FRAMEUNCHANGED
FROM BOX
FRAME UNCHANGED
FROM BOX
FRAME
3.22"
4"
J ROSOWSKI
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
23 OF 25A. LYNN MILLER, P.E.
P.E.# 1069547/27/2017
2-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
HEAD 135° CORNER CLUSTER ANCHORS LAYOUT (USING FRAME FIN ADDON):HEAD 90° CORNER CLUSTER ANCHORS LAYOUT (USING FRAME FIN ADDON):
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
EXTERIOR EXTERIOR
135°
90° ANCHOR LOCATIONS C
NTS
4"
4"
4"
4" 4"
4"
4"
2-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4-TRACK 90° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
2-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
2-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4-TRACK 135° CORNER"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
4-TRACK 135° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) DETAILS DEPICT ANCHOR QUANTITY AND SPACING, AND WOULD BESIMILAR FOR OUTSIDE (SHOWN) AND INSIDE CORNER CONFIGURATIONS.
3) TRACK-TO-TRACKDISTANCE IS 2.375": 2.375"
FIGURES PERTAIN TO THEFOLLOWING 135° CORNER
HEAD ANCHOR LOCATIONS:
FIGURES PERTAIN TO THE FOLLOWING 90° CORNERHEAD ANCHOR LOCATIONS:
EXTERIOR4-TRACK 90° CORNER"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
4"
3.22"
4"UNCHANGED
FROM BOX
FRAME UNCHANGED
FROM BOX
FRAME
UNCHANGED
FROM BOX
FRAME UNCHANGED
FROM BOX
FRAME
4"
4"
3.22"
4"
3.22"3.22"
4"
4"
3.22"
4"
4"
4"4"4"
4"4"
J ROSOWSKI
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
24 OF 25
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017
NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.
2) ABOVE FIGURES ARE FOR SPLICES OCCURRING AT THE ASTRAGAL OR INTERLOCK.FOR SPLICES OCCURRING INSIDE OF A POCKET, SEE THE EXAMPLE ON SHEET 9.
3) TRACK-TO-TRACKDISTANCE IS 2.375":
EXTERIOR EXTERIOR
EXTERIOR
SPLICELOCATION
SPLICELOCATION
SPLICELOCATION
SPLICELOCATION
4"4"2-TRACK SPLICE
"C4" ANCHOR LOCATIONS(USE WHERE "C3" IS SPECIFIED)
HEAD SPLICE ANCHORS LAYOUT @ INTERLOCK OR ASTRAGAL (USING FRAME FIN ADDON):
2.375"
FIGURES PERTAIN TO THE FOLLOWING SPLICEDHEAD ANCHOR LOCATIONS:
2-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
3-TRACK SPLICE"C4" ANCHOR LOCATIONS
(USE WHERE "C3" IS SPECIFIED)
3-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
®
1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600
EXTERIOR
ANCHOR LOCATIONS D
NTS
EXTERIOR
SPLICELOCATION
EXTERIOR
SPLICELOCATION
3.22"
4"4.75"
4"4-TRACK SPLICE
"C4" ANCHOR LOCATIONS(USE WHERE "C3" IS SPECIFIED)
4-TRACK SPLICE"C6" ANCHOR LOCATIONS
(USE WHERE "C5" IS SPECIFIED)
UNCHANGED
FROM BOX
FRAME UNCHANGED
FROM BOX
FRAME
2" 2"
3.22"
4" 4"
3.22"
J ROSOWSKI
SGD-5470
VINYL SLIDING GLASS DOOR TDI
TDI-SGD5470.2
3/24/16
1.625
.875
.125
FRAME FIN-ADDONALUMINUM 6063-T6PART # 19033
99
25 OF 25
A. LYNN MILLER, P.E. P.E.# 1069547/27/2017