safe, clean and reliable overfill protection systems
TRANSCRIPT
1
HYDRAU-FLO®
Mechanical and non-pressurised fuel filling valves
Safety Solutions for Liquid Filling
Safe, clean and reliable overfill protection systems
Refuelling rates up to 2100 lpm (555 gpm)
ExcellentMineralsSolutions
Contents
Deliverables .................................................................. 3
Global references .......................................................... 4
Applications .................................................................. 5
System overview ........................................................... 6
Selection table ............................................................. 7
Selection guide ............................................................. 8
Valves and breathers ..................................................... 9
Adaptors selection ...................................................... 10
Lines and connectors .................................................. 12
Valve dimensions ........................................................ 14
3 3
Hydrau-Flo® deliverables
Non-pressure refuelling is industries’ best practice
• Low cost solution
• Increases filling times by up to 83%, adding thousands of production hours to equipment fleets*
• Prevents overfilling, fuel spillage and waste
• Removes the operator from influencing fill levels
• Helps to eliminate fuel theft
Greatly improves safety and environmental outcomes
• Removes the risk of tank ruptures from pressure build up during and after filling
• Removes fuel spray associated with pressurised systems
• Minimises the risk of fire from fuel spillages
• Removes operator from the hot/red zone
• Allows for hot refuelling
• Allows for ground level refuelling
Tested and proven for 15 years
• Based on a proven mechanical principle of spring opposed hydraulic pressure
• Comprehensive 3 year warranty
• Simple installation
• Minimal maintenance
• Proven in extreme temperatures - 65°C (-85°F) with Environmental Exposure Certification
• Install base of over 30,000 units
• CE certified
*83% is based on calculated time savings for refuelling a fleet of Rubber Tyred Gantry Cranes
4
Hydrau-Flo® global references
Mining: • Trucks• Loaders • Excavators • Dozers• Diesel powered pumps• Lighting towers
Maritime: • Gantries • Cranes • Lighting towers • Diesel powered pumps • Generators
Oil & Gas: • Frac trucks • Static tanks • Automated refuelling solutions • Hot fuelling
Industrial: • Diesel powered pumps • Generators • Lighting towers • Static tanks • Transfer stations
Rail: • Locomotives • Storage tanks • Refuelling depots
5
Hydraulic fracturing application
Road transport application
Rail application
Hydrau-Flo® valve kits are manufactured to suit a wide range of industrial applications
in the mining, oil and gas, transport, construction & maritime sectors. These configurations are
designed for individual equipment needs using our professional engineering design service.
Hydrau-Flo® applications
Mining truck application
Gantry applicationLighting tower application
Mining grader application
Drill application
Mining service truck application
Mining dozer application
Mining excavator application
5
Dewatering pump application
6
The Hydrau-Flo® valve system is a safe, clean and reliable fuel filling valve arrangement
which removes the risk of overfilling, spillage and tank rupture while minimising safety
and environmental hazards associated with fuel transfer.
TOP: Hydrau-Flo® float control valve HF1008Z0007
LEFT: Hydrau-Flo® fuel filling black valve HF1105Z0001
Hydrau-Flo® system overview
When the float is down fluid bleeds into the tank through the pilot line
With higher pressure on top of the piston the valve remains open
Hydrau-Flo® fuel filling valve system:
• Flow rates up to 2100 lpm (555 gpm)
• Hydraulically actuated
• Operates on fluid level not pressure
• Used in conjunction with existing fast fill systems
• Prevents overfilling
• Prevents fuel spillage and wastage
• Removes the risk of tank rupture due to pressure build
up during and after filling
• Minimises the risk of fire as a result of fuel spillage
• Reduces costs associated with fuel wastage and
equipment damage
• Significantly improves safety and environmental
outcomes
• Ground level refuelling
Hydrau-Flo® system solution:
• System depends on fluid level, not tank pressure, and
cannot be overridden
• Fuel enters through the standard fast fill receiver and
Hydrau-Flo® fast filling valve
• A small portion of the flow is re-directed through a pilot
line to the float control valve
• Once the desired fuel level in the tank is reached, the flow
will be shut off
• The fuel in the pilot line now applies equal pressure to the
back of the fast filling valve
• The spring in the fast filling valve now acts as the
differential closing off the piston
For a more detailed description and presentation please scan this barcode into your mobile device. Alternatively please visit www.weirminerals.com/hydrauflo to watch the video.
7
Hydrau-Flo® valves selection table
What are the main drivers for this insallation? (Mark boxes 1 to 6 in order of priority)
Fast filling Overfill protection Fuel theft
Trickle feed Fuel surge Zero spill compliance
Requirement for criteria Customer response
1. What equipment (stationary or mobile) is the Hydrau- Flo® valve system to be fitted to? Is it a trickle feed system or fast fill requirement?
2. Make, model and year of manufacture of the machine, and fast fill system if known.
3. What is your required flow rate? (minimum & maximum)
4. What is the fuel tank capacity and material of construction?
5. What size are the inlet and outlets on the tank?
6. Can the tank be welded? (if applicable)
7. Are fuel inlets required on either side of the machine?
8. Is simultaneous dual or triple filling needed?
9. A capillary line which connects the tank inlet and outlet can be run internally or externally. Which is preferred? Magnet anchors are available for steel tanks (3/8” 104073 and 1/2” 104074)
10. Supply a drawing and/or photos of the fuel tank? (the more the better)
11. How many Hydrau- Flo® kits do you require?
12. Is this enquiry for a single piece of equipment or multiple pieces of equipment?
13. If the application is for trickle feed, is redundancy required? Use anti-surge breather HF1008Z0002.
14. Any further information regarding the tank?
15. Shipping location (city, state, country)
16. Timing of project (when do you expect to require the system)?
17. Do you require installation assistance, or do you have technical personnel on site to complete the installation?
7
8
A33rd ANGLE PROJECTION U.N.O.
APPROVEDDRAWING STATUS
Drawing Number
HF1102P0003 A0REV
SHEET 1 OF 1
ADAPTORSCALE
APPD
CHECK
DRAWN
DESIGN J.M
U.N.O.
11.08.14
11.08.14J.M
J.F 11.08.14
11.08.14J.FNo.
A0
-
-
-
-
- -
-
-
-
-
APPROVED FOR CONSTRUCTION
Description DATEAPPDCHKDWN
AS PER APPROVALS
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
- WELD CAT.
FINISH CODE
DO NOT SCALEIF IN DOUBT - ASK
MASS: 11.6 kg
MINE DEWATERING SOLUTIONS15 Dacmar Road Coolum Beach, QLD 4573 Australia
Telephone: +617 5449 3000 Facsimile: +617 5446 4304 Email: [email protected] Web: www.weirminerals.com
-
-
-
Copyright © Weir Minerals Australia Ltd. 2013Weir Minerals Austalia Ltd. ("the Company") is the owner of the copyright and all confidential information in this drawing.The drawing must not be copied in whole or in part, in any form or by any means, and the information in it must not be disclosed to any person, or used for any purpose other than the specific purpose for which it has been provided, without the prior written consent of the Company.
MULTIFLOMine Dewatering SolutionsHYDRAU-FLOSafety Solutions for Liquid Filling
®
®
FUEL FILLING ADAPTOR - PETRO
NOTE: FOR DRAWING, FABRICATION AND ASSEMBLY STANDARDS REFER TO WEIR MINERALS MULTIFLO ENGINEERING DEPARTMENT STANDARDS AND PROCEDURES.
MASSDESCRIPTIONPART NUMBERQTYITEM1.156 kgNPT 75mmHF1105Z0005113.62 kgFUEL FILLING ADAPTORHF1102P0003124.45872 kg2" NPT FLANGED ADAPTORHF1102P000413
259
3
2
1
n190.5
80 N.B ANSI 150 FLANGE
Hydrau-Flo® selection guideSelect your Receiver
Select your Fuel Filling Valve (FFV) - details page 9
Select your Adaptor - details page 10
Select your Lines and Connectors - details page 12
Select your Float Control Valve or Lever Control Valve - details page 9
Black FFV
Blue/Red/Gold
FFV
3/8” Pilot line
1/2” Pilot line
1 1/4” Exhaust
line
3/4” Breather
line
HF1105Z0001
HF1008Z0001
HF1105Z0002
HF1113Z0003 Banlaw (light)
HF1113Z0005 Hydrau-Flo 800lpm
HF1113Z0006 Hydrau-Flo 1500lpm HF1113Z0001
HF1113Z0002 Wiggins (5 PSI)
HF1008Z0009
HF1105Z0003
HF1008Z0007
HF1105Z0004 HF1105Z0006
HF1007Z0001 / HF1007Z0002
HF1105Z0007
HF1007Z0003 / HF1007Z0004
HF1105Z0010
HF1007Z0005
HF1103Z0006
HFS27-0604
HFS27-0804
HF1102Z0012 HF1102Z0013
103042
HF1204Z0013 HFS27-0806
HF1215Z0002
102907
102350
HF1011Z0002
HF1204Z0012
HF802-0808
HF1102Z0001
209304
214441
HHT16A
HF1102Z0004
225231
HF1103Z0002
HF1204Z0001
HF805-0808
HF1102Z0002
HF1102Z0007
HF1102Z0014
HF1102Z0008
HF1102Z0009 HF1102P0003
HF1102Z0003
HF1204Z0003
HF1102Z0005
HF1102Z0011
HF802-0606
104074
HF1102Z0015
HF1103Z0003
HF805-0606
HFS8-0409
HF1102Z0010
225232
HF1103Z0003
104073
HFS7-0409
216647
215249
216655
HF1204Z0002
HFT204-0609
HFS27-1212
HHP112
HF1215Z0004
HF1008Z0003 HF0304Z0003HF802-1212 106409 106408 HF1014Z0001 106040 106042 HF1014Z0002
RSC-4347
HF1011Z0001 HF1103Z0004
9
Hydrau-Flo® valves and breathers
BLACK - FFV For new applications andsome existing applications.
• Flow rate to 1000 lpm (264 gpm)
• Valve mounting 3” NPS• Male o-ring
HF1105Z0001
STANDARD 2” - FCVIncorporates rollover shut-off protectionand anti-surge.
• Tank fill rate to 1000 lpm (264 gpm)• Valve mounting 2” NPT male
HF1008Z0001
Stationary equipment only, skid mountedpump sets, generators & lighting plants.
• Valve mounting stem 7/8” UNF• Working pressure up to 1.5 bar
HF1007Z0001 - 110mm Stem HF1007Z0002 - 250mm Stem
Anti-surge breather has the same functionsas float control valves including rollover protection and fuel anti-surge.
• Tank fill rate to 1000 lpm (264gpm)• Valve mounting 2” NPT male
HF1008Z0002
Stationary equipment only, remote &gravity filling from an auxiliary fuel tank.
• Valve mounting stem 7/8” UNF• Working pressure up to 20 bar
HF1007Z0003 - 110mm Stem HF1007Z0004 - 250mm Stem
Anti-surge breather with filter option has thesame functions as the float control valves including rollover protection. Provides filtered air to preventfuel contamination. Capable of environmentalfiltering to 3 micron.
• Tank fill rate to 1000 lpm (264gpm)• Valve mounting 2” NPT male
HF1008Z0010
Mobile / stationary equipment, skid mountedpump sets, generators & lighting plants.
• Valve mounting stem 7/8” UNF• Working pressure up to 90 bar
HF1007Z0005 - 110mm Stem
1 ½” OPTION - STANDARD - FCVIncorporates rollover shut-off protectionand anti-surge.
• Tank fill rate to 1000 lpm (264 gpm)• Valve mounting 11/2” NPT male
HF1008Z0009
STANDARD 2” - FCV - WITH BREATHER OPTIONProvides filtered air to prevent fuelcontamination.Capable of environmental filtering to 3micron.
• Tank fill rate to 1000 lpm (264 gpm)• Filtration 3 micron using external filter• Valve mounting 2” NPT male
HF1008Z0007 (std) / HF1008Z0008 (short)
RED - FFVZNC3 Recess.
• Flow rate to 800 lpm (211 gpm)• Valve mounting 2” NPT male
HF1105Z0002
BLUE - FFVRetro fit for direct mounting to equipment tanks with 2” NPT female fittings.
• Flow rate to 650 lpm (171 gpm)• Valve mounting 2” NPT male
HF1105Z0003
BLUE - FFVFor compact machinery andunderground applications.
• Flow rate to 650 lpm (171 gpm)• Valve mounting 11/2” NPT
male
HF1105Z0004
GOLD - 1” - FFV• Flow Rate to 80 lpm
(21 gpm)• Valve mounting 1” NPT male
HF1105Z0006
GOLD - 2” - FFV• Flow rate to 800 lpm
(211 gpm)• Valve mounting 2” NPT male
HF1105Z0007
ORANGE - FFV• Flow rate to 1500 lpm
(396 gpm)• Valve Mounting 4” NPT male
HF1105Z0010
Fuel Filling Valves Float Control Valves
Lever Float Control Valve
Anti-Surge Breathers
9
10
Hydrau-Flo® Black Fuel Filling Valve
HF1105Z0001 • Valve mounting - 3” NPS male o-ring seal• Fuel connection - 2” NPT female
Black FFV to 2” NPT maleHF1102Z0001
Designed for use with Komatsu D375102350
Designed for use with CAT fuel tankHF1102Z0008
Designed for use with Hitachi EX 3600-6215189
Designed for use with Liebherr 994 / 996HF1102Z0007
Designed for use with John Deere fuel tank216647
Designed for use with CAT 16M 12 bolt flange fuel tank225232
Black FFV to2” hose tailHF1102Z0014Aluminium
Black FFV to weld-in flush mount C/W flangeHF1102Z0010
Black FFV to weld-on ringHF1102Z0002
Black FFV to 2 ½” hose tailHF1102Z0005 Steel
Black FFV to weld-on stand pipeHF1102Z0012 - 150mmHF1102Z0013 - 310mm
Black FFV to 2” SAE code 61225231
Black FFV to2” BSPT male102907
Designed for use with Liebherr Black FFV to 2’ SAE Code 61 HF1102Z0011
Designed for use with Lieb-herr Black FFV to 2 1/2” NPT female 214441
Black FFV to2” hose tailHF1102Z0004 Steel
Black FFV to 2 ½” hose tailHF1102Z0015 Aluminium
Black FFV to aluminium weld-on flange209304Aluminium
Black FFV ANSI 150 flangeHF1102P0003
Hydrau-Flo® adaptors selection
Hydrau-Flo® adaptors for use with Komatsu
equipment
Hydrau-Flo® adaptors for use with CAT
equipment
Hydrau-Flo® adaptors for use with Hitachi
equipment
Hydrau-Flo® adaptors for use with Liebherr
equipment
Hydrau-Flo® adaptors for use with John Deere
equipment
General
Designed for use with Hitachi EH 4000103042
Designed for use with Lieb-herr 994 / 996HF1102Z0009 Black FFV to 2” NPT male
Designed for use with CAT D10R / D11R FuelInlet 2” NPT male to 2” SAE Code 61HF1103Z0003
215249
A33rd ANGLE PROJECTION U.N.O.
APPROVEDDRAWING STATUS
Drawing Number
HF1102P0003 A0REV
SHEET 1 OF 1
ADAPTORSCALE
APPD
CHECK
DRAWN
DESIGN J.M
U.N.O.
11.08.14
11.08.14J.M
J.F 11.08.14
11.08.14J.FNo.
A0
-
-
-
-
- -
-
-
-
-
APPROVED FOR CONSTRUCTION
Description DATEAPPDCHKDWN
AS PER APPROVALS
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
- WELD CAT.
FINISH CODE
DO NOT SCALEIF IN DOUBT - ASK
MASS: 11.6 kg
MINE DEWATERING SOLUTIONS15 Dacmar Road Coolum Beach, QLD 4573 Australia
Telephone: +617 5449 3000 Facsimile: +617 5446 4304 Email: [email protected] Web: www.weirminerals.com
-
-
-
Copyright © Weir Minerals Australia Ltd. 2013Weir Minerals Austalia Ltd. ("the Company") is the owner of the copyright and all confidential information in this drawing.The drawing must not be copied in whole or in part, in any form or by any means, and the information in it must not be disclosed to any person, or used for any purpose other than the specific purpose for which it has been provided, without the prior written consent of the Company.
MULTIFLOMine Dewatering SolutionsHYDRAU-FLOSafety Solutions for Liquid Filling
®
®
FUEL FILLING ADAPTOR - PETRO
NOTE: FOR DRAWING, FABRICATION AND ASSEMBLY STANDARDS REFER TO WEIR MINERALS MULTIFLO ENGINEERING DEPARTMENT STANDARDS AND PROCEDURES.
MASSDESCRIPTIONPART NUMBERQTYITEM1.156 kgNPT 75mmHF1105Z0005113.62 kgFUEL FILLING ADAPTORHF1102P0003124.45872 kg2" NPT FLANGED ADAPTORHF1102P000413
259
3
2
1
n190.5
80 N.B ANSI 150 FLANGE
11
Hydrau-Flo® Lever Float Control Valve HF1007Z0001/HF1007Z0002
Hydrau-Flo® Lever Float Control Valve HF1007Z0003/HF1007Z0004
Hydrau-Flo® Lever Float Control Valve HF1007Z0005
• Valve mounting - 7/8” UNF male thread o-ring seal• Pilot line connection - 1/4” BSPT male thread
Designed for use with CATD10R / D11RFuel tankHF1011Z0001
Designed for use with CAT D10R / D11R Fuel TankHF1103Z0004
Designed for use with CAT D10R / D11RFuel inlet 2” NPT male to 2” SAE Code 61HF1103Z0003
Designed for use with Komatsu830e / 930eHF1102Z0003
4 Bolt - weld on float and breather mountHF1012Z0001
4 Bolt bolt-on float and breather mount7/8” UNF female thread (lever float) 3/4” BSPT female thread (breather std pipe HF101470001, breather HF0304Z0003)HF1012Z0002
Used with HF1012Z0002 or HF1012Z0003
Used with HF1014Z0001 Used with HF1012Z0002 Used with HF1012Z0002 or HF1012Z0003
Used with HF1012Z0001 or HF1103Z0001 Used with HF1103Z0001
Used with HF1012Z0001 or HF1103Z0001
Designed for use with John Deere Fuel tank216655
Breather3/4” BSPT male threadHF0304Z0003
4 Bolt bolt-on float mount 7/8” UNF female threadHF1012Z0003
4 Bolt screw-in float and breather mount2” male threadHF1103Z0001 NPT 221479 BSP
Weld on socket2” NPT female threadHF1011Z0002
Breather stand pipe 3/4” BSPT male x 3/4” BSPT female threadHF1014Z0001
Hydrau-Flo® adaptors for use with Wiggins equipment
Hydrau-Flo® adaptors for use with CAT equipment
Hydrau-Flo® adaptors for use with John Deere equipment
Hydrau-Flo® adaptors for use with Komatsu equipment
Designed for use with WigginsZNC3 / ZNC4Bolt-on / weld-onflush mountHF1103Z0006
11
Hydrau-Flo® Blue Fuel Filling Valve HF1105Z0003
Hydrau-Flo® Gold Fuel Filling Valve HF1105Z0007
Hydrau-Flo® Red Fuel Filling Valve HF1105Z0002
• Valve mounting - 2” NPT male• Fuel connection - 2” NPT female
Socket 2” NPTHF1011Z0002
Weld in recessedAdaptor 2” NPT femaleHF1103Z0002
General
12
3/8” Pilot Line
Pilot Line hose, fittings and accessories
Hydrau-Flo® lines and connectors
Nipple reducing3/8” BSPT M x 1/4”BSPT maleHFS27-0604
Nipple reducing1/2” BSPT male x 1/4” BSPT maleHFS27-0804
1/4” plugUsed for pluggingunused pilot lineportHF1204Z0003
Tee male3/8” BSPT maleHF1204Z0012
TEE male1/2” BSPT maleHFS50-080808
Elbow 90 deg male9/16” JIC male x 1/4”BSPT maleHFS8-0409
Pilot line check valve3/8” BSPT female x 3/8” BSPT femaleHF1204Z0002Used where 2 x filling valves are connected to 1 x float control valve. Includes balancing port.
Swivel hose tail3/8” BSPP female x 3/8” hose tailHF802-0606
Swivel hose tail1/2” BSPP female x 1/2” hose tailHF802-0808
3/8” Push on pilotline hoseSingle wire braidHHT16A
Pilot lineMagnetic anchorSuit 3/8” hose (16.5mmto 18mm hose OD)68kg (150 lbs) pull force104073
Pilot lineMagnetic anchorSuit 1/2” hose (20mmto 22mm hose OD)68kg (150 lbs) pull force104074
3/8” hose crimpCoupling9/16” JIC male x 3/8”hose crimpHFT204-0609
Adaptor3/8” BSPT female x 1/4” BSPT maleHF1204Z0013
Elbow 90 deg femaleSwivel hose tail3/8” BSPP female x 3/8” hose tailHF805-0606
Elbow 90 deg femaleSwivel hose tail1/2” BSPP female x 1/2” hose tailHF805-0808
Pilot line check valve3/8” BSPT female x 3/8” BSPT femaleHF1204Z0001Used where 1 x lever float valve is connected to 2 x fuel filling valves.
Nipple Reducing9/16” JIC male x1/4” BSPT maleHFS7-0409
1/2” push on pilotline hoseSingle textile braidHF1215Z0002
Nipple reducing3/8” BSPT male x 1/2” BSPT maleHFS27-0806
1/2” Pilot Line
13
3/4” Breather Line
1 1/4” Exhaust Line
Exhaust Line Float Control Valves & Breathershose, fittings and accessories
Hydrau-Flo® installation tools
Nipple3/4” BSPT male x 3/4” BSPT maleHFS27-1212
1 1/4” push on exhaust line hoseSingle textile braidSuit all green float valves & breathersHF1215Z0004
Steel rain capBreather3/4” BSPT maleHF0304Z0003
Hydrau-Flo® float control valve install tool - side entry200629
Hydrau-Flo® fuel filling (blue and black) valve install tool - side entry201240
Hydrau-Flo® fuel filling red valve install tool202125
Hydrau-Flo® fuel filling (blue and black) valve install tool - top entry101023
Hydrau-Flo® Tool kit103628
Elbow 90 degFemale / male3/4” BSFT female x 3/4” BSPT male106408
Nylon air breather3 micron3/4” NPT maleBuilt in restriction indicator106042Replaceable element106043
Swivel hose tail3/4” BSPP female x 3/4” hose tailHF802-1212
1 1/4” hose clampSingle textile braidRSC-4347
3/4” push on pilotline hoseSingle textile braidHHP112
Barrel nipple3/4” BSPT maleFor mounting HF0304Z003Rain cap breatherHF1014Z0001
Bracket weld-on /bolt-on3/4” BSPT male(Suit rain cap HF0304Z0003)HF1014Z0002
Hose tail3/4” BSPT male x 3/4” hose tail106409
Steel air breather3 micron3/4” NPT male106040
Breather mountingFlange3/4” BSPT male to anti-surge breatherHF1008Z0003
13
14
Hydrau-Flo® valves dimensions
Fuel Filling Valves (FFV)
Float Control Valves (FCV)
Ø100 (3.93”)126mmØ
104mmØ
(4.9ӯ)
(4ӯ)
1/4” BSPT
3” NPS
4” NPT
70 (2
.75”) 11
7 (4.6
”)133 (
5.2”)
50m
m
(1.9”
)
HF1105Z0001HF1105Z0010
HF1105Z0002 HF1105Z0003
HF1105Z0007
HF1105Z0006
HF1008Z0006 HF1009Z0001 HF1008Z0007HF1008Z0001
15
Lever Float Control Valves
Anti-Surge Breathers (ASB)
S = 48 + 11 + T
S = SETTING DISTANCET = THICKNESS OF FUEL TANK MATERIAL
Eg. 48 + 11 + 6 = 65mm
48
SET WITH FLOAT CLOSED
266mm (10.4”)
129mm (5”)
115mm (4.5”)115mm (4.5”)2”NPT2”NPT
220m
m (
8.8”
)
122m
m (
4.8”
)
HF1008Z0010HF1008Z0002
FLOAT CLOSED
FLOAT OPEN
11
6 (T
)
65 (
S)
15
HF1007Z0004
HF1008Z0002 HF1008Z0010
HF1007Z0005 HF1007Z0001 HF1007Z0002 HF1007Z0003
Weir Minerals Australia Ltd. All rights reserved. WARMAN is a trademark and/or registered trademark of Weir Minerals Australia Ltd and Weir Group African IP Ltd; CAVEX, HYDRAU-FLO and MULTIFLO are trademarks and/or registered trademarks of Weir Minerals Australia Ltd; GEHO is a trademark and/or registered trademark of Weir Minerals Netherlands bv; FLOWAY is a trademark and/or registered trademark of Weir Floway Inc.; VULCO is a trademark and/or registered trademark of Vulco SA; ISOGATE is a trademark and/or registered trademark of Weir do Brasil Ltda.; LINATEX is a trademark and/or registered trademark of Linatex Ltd; ENDURON is a trademark and/or registered trademark of Weir Minerals Europe Ltd; WEIR is a trademark and/or registered trademark of Weir Engineering Services Ltd. KOMATSU, CAT, HITACHI, LIEBHERR, JOHN DEERE and WIGGINS are not trademarks belonging to any company forming part of The Weir Group PLC.
* KHD is a Humboldt Wedag GmbH brand used under license by The Weir Group.
Issu
ed Ju
ne
2014
Weir Minerals Multiflo 15 Dacmar Road Coolum Beach QLD 4573 Australia
T +61 (0)7 5449 3000 F +61 (0)7 5449 4304
[email protected] www.weirminerals.com
Weir Minerals Multiflo is a business unit of Weir Minerals Australia Ltd.
ExcellentMineralsSolutions
Enquiries:Office: Equipment Placement, 170 Kewdale Road, Kewdale, WA, 6105Postal: PO Box 834, Cloverdale, WA 6985Email: [email protected]
Sold and Serviced by: