ROAD AND BUILDING MATERIALS TESTING

I. --- AGGREGATE (IS :383; 2386; 6241)

S.

No. Name of Test

Rate per Test

(to be quoted in Rs./test)

In

figure

In words

1. Impact Value

2. Sieve Analysis( Gradation)

3. Crushing Value

4. Abrasion Value

5. Water Absorption

6. Specific Gravity

7. Bulk Density

8. Soundness

9. Flakiness Index

10. Elongation Index

11. Deleterious material

12. Stripping value

13. Petrography examination of

aggregates( Macro)

14. Alkali Aggregate Reactivity

15. 10% fine value

16. WMM Mix Design(as per

MORT& H)*/GSB/WMM

II. --- FINE AGGREGATE/SAND (IS: 383; 2720.)

S.

No. Name of Test

Rate per Test

(to be quoted in Rs./test)

In

figure

In words

1. Sieve Analysis (Gradation)

2. Bulk Density

3. Bulking

4. Specific Gravity

5. Silt Content

6. Proctor test (OMC & Maximum

Dry Density) Light / heavy

Compaction

7. CBR test in Soaked / Unsoaked

conditions

8. Fineness Modulus

9. Organic Impurities / Deleterious

Material

10. Surface Moisture Content

11. Water Absorption

12. Soundness

13. Alkali Aggregate Reactivity

III. --- CEMENT (IS:269; 8112; 12269; 4031;4032;)

S.

No. Name of Test

Rate per Test

(to be quoted in Rs./test)

In

figure

In words

A PHYSICAL TESTING

1. Fineness (Dry Sieving test)

2. Fineness (by Blain Air permeability)

3. Consistency & Setting Time

4. Compressive Strength of Cubes

(3 Cement Cubes (including

preparation of sample)

Consistency with IST

5. Soundness (Lechateliers test)

6. Soundness(Autoclave Test)

7. Density

B CHEMICAL TESTING

1. Loss on Ignition

2. Silica (SiO2)

3. Alumina (Al2O3)

4. Ferric Oxide (Fe2O3)

5. Calcium Oxide (CaO)

6. Magnesia (MgO)

7. Sulphuric Anhydride (SO3)

8. Insoluble Residue (IR)

9. Sodium Oxide (Na2O)

10. Potassium Oxide (K2O)

11. Free Lime (CaO)

12. Chloride (Cl-)

IV. --- CEMENT CONCRETE (IS: 1199; 516; 456;15658; 10262)

S.

No. Name of Test

Rate per Test

(to be quoted in Rs./test)

In

figure

In words

1. Compressive strength (Cement

/ Cement concrete cubes /

Paver Blocks)

2. Concrete Mix design including

lab. Testing.

3. Workability by Slump test /

Compaction Factor Test

4. Flexural Strength (Three point loading )

5. Compressive strength

(Concrete Core)

V. --- NON DESTRUCTIVE TESTS* (IS: 1331(Pt-I, II etc.))

S. Name of Test Rate per Test

(to be quoted in Rs./test)

No. In

figure

In words

1. Rebound Hammer test at one

location at Jaipur

(Excluding Transportation)

2. To determine the compressive

strength/depth of cracks by

Ultrasonic Pulse Velocity meter

3. To measure the degree of

corrosion of Reinforcement by

Corrosion Meter

(Half Cell Potential Meter)

VI. --- BRICKS (IS: 1077; 3495)

S.

No. Name of Test

Rate per Test

(to be quoted in Rs./test)

In

figure

In words

1. Dimension tolerance

2. Water Absorption

3. Compressive Strength

4. Efflorescence

5. Visual Examination

VII. --- SOIL (IS : 2720.)

S.

No. Name of Test

Rate per Test

(to be quoted in Rs./test)

In

figure

In words

Physical Tests:

1. Water content

2. Specific Gravity

3. Liquid Limit/Plastic Limit

4. Shrinkage Limit

5. Compaction Test by Proctor

method (OMC & Max. Dry

Density) for Light / heavy

Compaction

6 CBR test in Soaked / Unsoaked

conditions

7. Wet Sieve Analysis

8. Hydrometer analysis for Grain

Size (Silt & Clay)

9. Density Index

10. Triaxial Shear test without pore

pressure measurement

11. Triaxial Shear test with pore

pressure measurement

12. Consolidation test

13. Unconfined compression test

14. Bulk Density

15. Direct Shear test

16. Swelling Pressure

17. Permeability of soil (Lab.)

18. Differential free Swell (free

Swell index)

Chemical Tests

19. pH, Chloride, Sulphate

IX. --- BITUMEN (Industrial/Paving/Poly modified)/ EMULSION (IS: 1201; 1220;

1205; 1203; 1206, 1208; 3117; 8887,15462.)

S.

No. Name of Test

Rate per Test

(to be quoted in Rs./test)

In figure In words

1. Specific gravity

2. Softening point

3. Penetration test

4. Viscosity( Absolute / Kinematic)

5. Ductility

6. Flash Point/Fire Point

7. Solubility in Trichloroethylene

8. Loss on heating % by weight*

(Test on Residue from Thin Film

Oven)

9. Job mix formula by Marshall

Stability Test *

(a) B.M./DBM/ SDBC/BC

10. Striping value

11. Bitumen Content

12. Residue on 600 micron

13. Viscosity by Saybolt furol

Viscometer( At 250C/ 500C)

14. Coagulation of Emulsion

15. Storage Stability

16. Coating Ability and Water

Resistance

17. Miscibility With Water

18. Water Content

19. Residue by Evaporation

20. Elastic Recovery/ at 15C*

21. Penetration of Residue

22. Particle Charges

23. Distillation

24. Stability With Mixing of

Cement

X. --- GLAZED STONEWARE PIPES AND FITTINGS (IS: 651)

S.

No

.

Name of Test

Rate per Test

(to be quoted in Rs./test)

In figure In words

1. Hydraulic Test

2. Absorption Test

3. Crushing Strength Test

4. Alkali Resistance

5. Acid Resistance

XI. --- STEEL (IS: 1786; 1608; IS: 1599, 14268)

S.

No. Name of Test

Rate per Test

(to be quoted in Rs./test)

In

figure

In words

1. Tensile Strength Test (Ultimate

Strength, 0.2% proof stress, Yield

stress, Elongation, Nominal

Mass)

2. Weight per meter

3. Bend Test/ Reverse Bend Test

4. Rebend Test

5. Rib Area

Chemical Tests

1. Carbon

2. Sulphur

3. Phosphorus

4. Silica (SiO2)

5. Manganese

6. Nitrogen content*

XII. --- TILES (TERRAZO /MARBLE/GLAZED/CERAMIC TILES/CHEQUERED

CEMENT CONCRETE) (IS: 1130; 777; 13753; 13754; 13755; 13756, 13630,

13801.)

S. Name of Test Rate per Test

(to be quoted in Rs./test)

No. In

figure

In words

1. Water Absorption

2. Dimension & Visual

Examination

3. Wet Transverse Strength /

Modulus of Rupture

4. Abrasion Resistance

5. Flatness

6. Straightness

7. Perpendicularity

8. Chemical Resistance

9. Hardness

XIII. WATER (IS: 456)

S.

No

.

Name of Test

Rate per Test

(to be quoted in Rs./test)

In figure In words

1. pH, Chloride, Sulphate

2. Tests of water for construction

purpose as per IS:456

XIV.. PLYWOOD (Plywood, Particle Board, Door Shutter)(IS:303, 1734, 2380, 4020)

S.

No

.

Name of Test

Rate per Test

(to be quoted in Rs./test)

In figure In words

1. Density

2. Moisture Content

3. Resistance to Dry Heat

4. Water Absorption

5. Dimension & Squareness

6. End Immersion Test

7. Measurement of General

Flatness

8. pH

9. Acidity and Alkalinity resistance