8/6/2019 Ribbon Hari Bows

http://slidepdf.com/reader/full/ribbon-hari-bows 1/2

RIBBO

Give Me

 An easy, ho5 designer h

{

The Corker Bow

4. Criss-cross the cut curls (as shown) and secure

in the center with thread.

5. Glue bow to hair clip. Trim curls as needed, and

u bow.

1. Tightly wrap

ribbon around

dowel rods

and secure

with clamps at

both ends.

SUPPLY LIST

Assorted ribbons, narrow-width

Fabric stiener

Three 1/4˝ dowel rods

Needle and Thread

3. Make loops as

shown with other 30˝ 

length o 3/8˝ and 5/8˝ 

ribbon, placing one

ribbon atop the other.

Form a cloverlea shape

and make sure loops

are even, then hot glue

ribbon layers together.

4. With a 29˝ 

length o 1 ½˝ 

wide ribbon, make

a narrow Figure 8.

Bring in the ends,

weave the needle

through and cinchtogether. Wrap

thread around and tie o.

5. Place the wider

7” ribbon on

bottom, then make

an “X” on top with

the two narrow

7˝ ribbons. Tack

together in center.

6. Layer the ribbons

and arrange as

desired on top o the

ribbon spray. Wrap a

French knot around all

the layers and glue in

back. Attach hair clip.

Trim ends and apply

Fray Check.

1. Using a 30˝ length o 1 ½˝ wide

ribbon, make a wide fgure 8.

2. Bring ends o loop

to center, as shown,

and weave needle and

thread through center

and cinch together.

Wrap thread around

center and tie o in

back o bow.

  www.hobbylobby.com www.getinspire dbyhl.com Fabric - 357814

©2010 Hobby Lobby® - The information in these instructions is presented in good faith, but no warranty is given, nor results guaranteed, nor is freedom from any  patent to be inferred. Since we have no control over physical conditions surrounding the application of information herein contained, Hobby Lobby Stores, Inc.

disclaims any liability for untoward results. Follow manufacturer’s instructions in using paints and other materials, keeping them out of reach of children,since some may be toxic, or otherwise cause injury. Photography by Sanford Mauldin.

The Four-Layer Loopy BowSUPPLY LIST

Two lengths of 3/8˝ wide ribbon, each 30˝ long

Two lengths of 5/8˝ ribbon for spray, each 7˝ long

Length of 1 ½˝ wide ribbon, 30˝ long

Length of 1 ½˝ wide ribbon, 29˝ long

One length of 5/8˝ ribbon, 30˝ long

One length of 7/8˝ ribbon for spray, 7˝ long

Hair clip

Fray Check

Needle and thread

Scissors

Hot glue gun

2. Using paintbrush, apply abric stiener and

thoroughly coat ribbon. Let dry overnight.

3. Once dry, gently remove ribbon rom the dowel

rods and cut to desired length. Ours were 6˝ long.

Hair clip

Binder clips

Paintbrush

Scissors

Hot glue gun

8/6/2019 Ribbon Hari Bows

http://slidepdf.com/reader/full/ribbon-hari-bows 2/2

The Pinwheel

SUPPLY LIST

Ribbon (approximately 2 yards)

Hair clip

Jewelry wire (approximately 9˝)

Fray Check

Adhesive tape runner

Scissors

Hot glue gun

5. Wrap French knot around center and glue in

back. Adhere hair clip to back. Trim ends and apply

Fray Check.

2. Loop

ribbon length

around hand

with ends

pointing in

opposite

directions,

as shown.

3. Lay at, taking care not to move loops.

Pinch the center o loops to create a gather.

4. Wrap gathered center with jewelry wire to

secure loops.

5. To create rench knot, see steps 6-8 o

Three-Tiered Bow.

6. Hot glue knot in center, covering the wire, and

wrap ends to back. Also secure hair clip to the back

of bow with glue.

1. Cut o a 10˝ length o ribbon and set aside. Cut

remaining ribbon in hal, then adhere these two

pieces back to back. Trim ends with a “V” shape

and apply Fray Check.

The Triple Stack

SUPPPLY LIST

Three dierent patterns o ribbon,

approximately 1 ½˝ wide each

Xyron®

Hair Clip

Fray Check

Needle and thread

Scissors

Hot glue gun

2. For each pattern o ribbon, make a Figure

8 as shown, leaving 2˝ o ribbon ree on

one end.

1. To apply adhesive to back o ribbon, cut two

pieces rom each ribbon pattern each 19˝ long.

Run one 19˝ piece through the Xyron®, then

adhere to the matching length.

3. Careully pinch center and weave needle and thread

in and out o the layers to secure the loops.

4. Repeat Steps 2 and 3 with other two

ribbon patterns. Stack ribbon layers as

desired and tack together.

2. Repeat, making

needle and thread

shown, to secure

4. Stack each

tier, sewing

middle tier to

bottom tier,

then top tier

to middle to

secure.

6. To make the Fr

a piece o ribbon

10˝ long and loop

SUPPPLY LIST

1˝ wide satin r

½” wide satin

1˝ wide grosgr

Hair clip

The Thr

1. For the bottom

ribbons 32˝ long.

side out, and mak