regulators, valves & systems - · pdf filehigh pressure - pressure reducing regulators...

Pressure controls for your industry

a world of

REGULATORS, VALVES & SYSTEMS

HANDKNOBLarge handknob provides easy, lowtorque pressure setting. Wrench or screwdriver adjust options on some models.

VENTINGVenting feature enables relieving of the outlet pressure when the handknob is turned in the “decrease” direction.Captured venting configuration includes extra port to pipe away expelled fluids from a regulator’s vent valve.Non-venting feature available for hydraulic or other applications where venting is not desirable.

FLOW CAPACITY – Cv Cv is a measure of regulator flow capacity. The flow coefficient refers to the flow of one GPM of water at one psi drop across the main valve. The coefficient for gaseous service must be determined from the ratio of inlet to outlet pressure.

BODY MATERIALSBrass, aluminum or stainless steel (Type 300, 316) and others.

OUTLET PRESSURE RANGES AVAILABLEStarting at 50 mm Hg absolute to 15 psig / 1 bar, ranging up to 300-20,000 psig / 21-1379 bar.

LOADING – Spring, Dome, Air Actuated, ElectronicLoading refers to the method used to balance the outlet pressure. Spring loading is used with direct acting regulators with handknob adjustment. Dome loading is most often used in high flow, quick response type applications.Air Actuator provides outlet pressures up to 15,000 psig / 1035 bar with a signal of only 100 psig / 6.9 bar. A TESCOM electronic controller is another loading option.

PANEL MOUNTINGStandard on some models. Extra option on others.

SENSING – Diaphragm or PistonDiaphragms provide sensitive and accurate regulation for outlet pressure ranges up to 500 psig / 35 bar. Piston sensors provide high strength integrity for high outlet pressures up to 20,000 psig / 1379 bar.

INLET PRESSURE RANGESSub-atmospheric to 20,000 psig / 1379 bar.

PORTSSizes: 1/8" to 1"Types: NPTF (all models), SAE, Aminco, MS33649,

Slimline, BSP, welded fittings.

MAIN VALVES – Balanced and UnbalancedBalanced design is used to reduce the effect of decaying inlet pressure and in certain models provides increased flow capacity.Unbalanced valve offers simplicity and economy.

ADDITIONAL CONSIDERATIONS• Gauge ports, 1/8" or 1/4" NPTF • Temperature range • Corrosion resistance • Welded connections • Soft goods-Buna-N, PCTFE, Teflon®,

Viton-A®, Vespel® and EPR.

Major considerations in the selection of a regulator are listed here. Within the requirements of your specific application, use this catalog to find the regulator that matches your parameters. Our standard products are only a starting point. We can modify or create a control that will solve your toughest application problem. Detailed information is available through your local TESCOM representative.

Elgiloy® is a registered trademark of Elgiloy Corp.Gylon® is a registered trademark of Garlock, Inc.LabVIEW® is a registered trademark of National Instruments.Hastelloy® is a registered trademark of Haynes International, Inc. Teflon®, Viton-A® and Vespel® are registered trademarks of E.I. du Pont de Nemours. Windows® and Visual Basic® are registered trademarks of Microsoft Corporation.

What to consider when choosing a regulator

Contents

INLET

OUTLET

High Pressure – Pressure Reducing Regulators. . . . . . . 1Low Pressure – Pressure Reducing Regulators . . . . . . . 2Low Pressure – Vacuum & Absolute Regulators . . . . . . 2High Flow – Pressure Reducing Regulators . . . . . . . . . . 3 Back Pressure Regulators . . . . . . . . . . . . . . . . . . . . . . . . . 4Hydraulic Regulators – Reducing & Back Pressure . . . . 5-6Corrosion Resistant Regulators . . . . . . . . . . . . . . . . . . 6-7Custom – Reducing & Back Pressure. . . . . . . . . . . . . . . 7-8

Alternative Fuels Regulators . . . . . . . . . . . . . . . . . . . . . . . 8Pharmpure™ Regulators for Life Sciences . . . . . . . . . . 8-9Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Changeover Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . 10Integrated Custom Systems . . . . . . . . . . . . . . . . . . . . . . 10Electronic Pressure Controls. . . . . . . . . . . . . . . . . . . 11-12Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12About TESCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

High Pressure - Pressure Reducing Regulators

BB-1 Miniature

26-2000 Versatile

44-1100 High Pressure

26-1000 Versatile

1

Outlet Pressure Ranges Flow Capacity Body

Material

InletPressure

Maximum

InletPressure

(maximum)


MaterialProduct Series/Features(Pressure Reducing)

BB-1 Series: Miniature •Lightweight,compactdesign 6000psig 0-80,0-140, Cv=.06 Aluminum, •Pistonsensedforhighcyclelife 414bar 0-220,0-700, 316SST •Designedforliquidorgasmedia 0-1200,0-1800psig •Non-venting 0-5.5,0-9.7,0-15.2, •Fieldadjustableorpre-setranges 0-48.3,0-83,0-124bar

BB-5 Series: Miniature, Two Stage •Lightweight,compactdesign 6000psig 0-80,0-140,0-220, Cv=.06 Aluminum, •Interstagereliefport 414bar 0-700,0-1200psig 316SST •Pistonsensedforhighcyclelife 0-5.5,0-9.7,0-15.2, •Non-venting 0-48.3,0-83bar

44-1100 Series: High Pressure •Excellentsensitivity 6000, 5-500,5-800, Cv=.02 Brass, •Pistonsensedforhighcyclelife 10,000psig 10-1500,15-2500, Cv=.06 300 SST, •Inlet&outletgaugeportsstandard 414, 690 bar 25-4000, 50-6000 Cv=.12 316 SST •40micron(nominal)inletfilter psig •Removablevalvemoduleforeasy .35-35,.35-55.2, field repair .69-103.4, 1-172.4 •Ventingstandard 1.7-275.8,3.5-414bar

44-1800 Series: Economy •Generalpurposeuse 6000 psig 15-2500 psig Cv=.06 Brass, •Compactdesign 414bar 1-172.4 Cv=.24 300 SST, •Adjustablestoplimitsmaximum 316SST outlet pressure •Inlet&outletgaugeportsstandard •Non-ventingstandard

26-1000 Series: Versatile •Outletpressurerangesare 6000 & 5-500, 5-800, Cv=.02 Brass, field changeable 10,000 psig 10-1500, 15-2500, Cv=.06 300 SST, •Numerousportingoptions 690,414bar 25-4000,50-6000, Cv=.12 316 SST •Optionalinletpressures 200-10,000psig Cv=.3 to 20,000 psig / 1379 bar .35-35, .35-55.2, •Largehandknobprovidesfast .69-103.4, 1-172.4 low-torque pressure settings 14-690 bar •Ventingstandard

26-2000 Series: Versatile •Designedforbothhydraulicand 6000, 10,000 5-500, 5-800, Cv=.02 Brass, pneumatic service & 15,000 psig 10-1500, 15-2500, Cv=.06 316 SST •Segregatedandcapturedventing 690,414, 25-4000,50-6000, Cv=.12 •Designedforheavydutyshock 1035bar 200-10,000psig Cv=.3 and vibration service .35-35, .35-55.2, •Choiceofmetaltometalor .69-103.4, 1-172.4 soft seat 1.7-275, 3.5-413 •Optionalinletpressuresupto 14-690bar 30,000 psig / 2070 bar & outlet pressures up to 20,000 psig / 1379 bar •CompatiblewithTESCOM Electronic Controllers (p. 11-12)

26-1600 Venting

Low Pressure - Pressure Reducing Regulators

2

44-5200Economical/Venting

DK Series

InletPressure

(maximum)Outlet Pressure

Ranges Flow Capacity Body Material

Product Series/Features(Pressure Reducing)

DV Vacuum Control

InletPressure



Product Series/Features(Absolute)

Low Pressure - Vacuum & Absolute Regulators

44-4700 Back Pressure

44-4600 Series: Absolute Pressure •ControlledPressureRange:28"Hg 120, 3500 psig 28" Hg Vac to Cv=.06 316L SST to 15 psig 8.2, 241.3 bar 15 psig /1 bar Cv=.24 •Large diaphragm - excellent sensitivity

DA Series: Absolute Pressure •Sub-atmosphericto350psig 4500, 500 psig Vac. to 15 psig /1 bar Cv=.06 Brass or •Non-ventingregulator 310.3,35bar Vac.to50psig/3.5bar Aluminum •Elastomericdiaphragmsensor- Vac.to100psig/6.9bar highly sensitive Vac. to 350 psig /10.4 bar •Economical •Lowknobtorque,quickresponse •Domeloadedoption

44-4700 Series: Sub-atmospheric, Back Pressure •HighFlowcapacity 28" Hg vac - 15 psig /1 bar Cv=.04 316L SST •Negativespringbias 28"Hgvac-50psig/3.5bar Cv=.30 •Controlssub-atmosphericto 28"Hgvac-100psig/6.9bar positive pressures 28" Hg vac - 150 psig /10.4 bar

DV Series: Vacuum control •Elastomericdiaphragm-highlysensitive 0psig-28"Hg Cv=.25 Brass or •Highlyaccurate:±1% (non-bleed) Aluminum •Domeloadedoption 0psig-25"Hg •Choiceofconstantornobleed (constantbleed)

Controlled PressureRanges Flow Capacity Body

MaterialProduct Series/Features(Vacuum)

26-1500 Series: Non-venting • Non-ventingregulator 6000, 4-50,4-150, Cv=.08 Brass or • Compactdesign 5000psig 4-250psig Cv= .24 316 SST • Elastomericdiaphragm- 414,345bar .28-3.5,.28-10.4, highly sensitive .28-17.2 bar • Domeloadingavailable • Forliquidorgasservice 26-1600 Series: Venting • Elastomericdiaphragm- 6000, 2-50,2-150, Cv=.08 Brass or highly sensitive 5000 psig 3-250, 5-500 psig Cv=.24 316 SST •Controlsupto500psig 414,345bar .14-3.5,.14-10.4, • Domeloadingavailable .2-17.2,.35-35bar • Forliquidorgasservice •WorkswithTESCOMmotorizedactuatorforremotecontrol

44-5200 Series: Economical/Venting/Non-Venting • Replaces44-2200V 3500, 400 psig 0-25, 0-50, 0-100, Cv=.06 Brass or • Large piston - good sensitivity 241.3, 27.6 bar 0-250, 0-500, 0-600 psig Cv=.15 316 SST • Forliquidorgasservice 0-1.7, 0-3.5, 0-6.9, 0-17.2, 0-35, 0-41.4 bar DK Series: Segregated and Captured Venting • Improvescontrolandresolutionat 1000psig Airload: Cv=.35 Brass or medium flows & pressures 69 bar 0-600 psig 316 SST •Remote control capability with 0-41.4 bar TESCOM 26-1200 regulator Dome load: • Designedforusewith 0-700 psig TESCOM ER5000 (p. 11) 0-48.3 bar

High Flow - Pressure Reducing Regulators


MaterialProduct Series/Features(Pressure Reducing)

26-1200 Cv =12

3

44-1300 Versatile

44-4000 Tracking

InletPressure

(maximum) 26-1100 Series: Compact/High Flow •Diaphragmsensed-highlysensitive 6000, 55-6000, Cv=.46 Brass, •Modularconstruction-easyservice 10,000 psig 55-10,000 psig Cv=1.3 300 SST or •Externalsensingavailablefor 414,690bar 3.8-414, 316SST improved accuracy 3.8-690 bar •Balancedmainvalveincreasesseatlife

26-1200 Series: High Flow •Similarto26-1100abovewith 6000psig 100-6000psig Cv=3.3 300 SST or higher flow capacity 414 bar 6.9-414 bar Cv=6.0 316 SST Cv=12.0

44-1300 Series: Versatile •Excellentsensitivity 3750, 4500 10-300, 15-600, Cv=.8 Brass, •Venting 5000, 6000 psig 20-1000, 50-1500, Cv=2.0 300 SST or •Extremelyreliable 259,310, 50-3000psig 316SST •Spring,domeorairratioloading 345,414bar .69-20.1,1-41.4,1.4-69, 1.4-103, 1.4-207 bar

44-1500 Series: High Flow •Segregatedandcapturedventing 6000 psig 10-200, 10-400, Cv=.3 Brass or •6000psiginlet 414bar 10-600psig 316SST •Spring,domeorairratio .69-14,.69-27.6, loading available .69-41.4 bar

44-4000 Series: Tracking •Segregatedandcapturedventing 6000 psig 50-1, 500 psig Cv=.7 Brass, •Adjustablebiaspressures 414bar 3.5-103.4bar Cv=2.0 300 SST or •Airactuatedmodelsarecompatible PlusBiasPressures 316SST with TESCOM electronic pressure Pressures to 350 psig controllers (p. 11-12) 24.1 bar

44-4200 Series: Economical •Domeloaded 6000 psig 0-5000 psig Cv=.8 Brass, •Pistonsensed-highlyreliable 414bar 0-345bar Cv=2.0 300 SST or •CompatiblewithTESCOMelectronic 316SST pressure controllers (p. 11-12)

CP32 Series: Pilot Operated •Highflow,lowdroop 3000 psig 500 psig Cv=1.0 Brass or •Gaugeportoption 207bar 35bar 316SST •Excellentsensitivityandrepeatability DH Series: Low Pressure •Diaphragmsensed-highlysensitive 500 psig 0-20, 0-50, 0-100, Cv=5.0 Brass or •Excellentrepeatability 35bar 0-150,2-250psig 316SST •Veryhighflowsatlowpressures 0-1.4,0-3.5,0-6.9, 0-10.4, .14-17.2 bar DG Series: Low Pressure •Diaphragmsensed 300psig 0-20,0-50,0-100 Cv=10 316 SST •Highflow-upto1400scfm 21bar 0-250psig •NPTF&weldedconnections 0-1.4,0-3.5,0-6.9, 0-17.2 bar

CP32 Pilot Operated

DH Low Pressure

Back Pressure Regulators

4

26-1700Versatile

26-2300 High Accuracy

26-2500 High Flow

44-1700 Economical

Controlled Pressure Ranges Flow Capacity Body

MaterialProduct Series/Features(Back Pressure)

26-1700 Series: Versatile •Extremelysensitive 5-500,5-800,10-1500 Cv=.02 316 SST •Idealforbothgas&liquidservice 15-2500, 25-4000, 50-6000, Cv=.10 •Hightemperatureversionsavailable 200-10,000,200-15,000psig Cv=.14 up to 400°F / 204°C .35-35, .35-55.2, .69-103.4, Cv=.60 •Accuracy:± 1%ofrelief 1-172.4,1.7-275.8,3.5-414, pressure range 14-690, 14-1035 bar

26-2300 Series: High Accuracy •Precisepressurecontrol 5-50,10-150,10-250psig Cv=.06 300 or 316 •Diaphragmsensed -highly sensitive .35-3.5, .69-10.4, .69-17.2 bar Cv=.60 SST •Cracktoreseat:2%ofsetpressure Cv=1.0 •Bubble-tightshutoffatall reseating pressures

26-2500 Series: High Flow •LargeGylon® diaphragm for 0-20, 0-50, 0-125, 0-200 psig Cv=5.0 Brass or excellent sensitivity 0-1.4, 0-3.5, 0-8.6, 0-14 bar 316 SST •Bubble-tightshutoffatall reseating pressures •1/2",3/4"and1"inletand outlet port sizes

26-2900 Series: Tracking •HighFlow 1000psig Cv=2.0 Brass or •Negativespringbias 69bar 300SST •DesignedforBIBSapplication •Diaphragmsensed-highlysensitive

44-1700 Series: Economical •Pistonsensed-highlyreliable 40-150, 100-700 or Cv=.10 Brass or •Compactdesign 100-800psig 316SST •Closepressuredifferentialbetween 2.8-10.4,6.9-48.3, crack and reseat 6.9-55.2 bar •Adjustablepressurestopstandard

BB-3 Series: Miniature •Economical&extremelycompact 0-80, 0-140, 0-220, Cv=.20 Aluminum •Durablepistonsensordesign 0-250*,0-3000*psig Cv=.50 or 316 SST •Hightemperature 0-5.5,0-9.7,0-15.2, (to400°F/204.4°C)version 0-17.2*,0-207*bar •Highflowcapacity *dome load only

44-2300 Series: Economical •Handadjustable 0-25, 0-50, 0-100, 0-250 psig Cv=.08 Brass or •Diaphragm-sensed 0-1.7,0-3.5,0-6.9,0-17.2bar 316LSST •Domeloaded •Fourcontrolpressureranges

44-4700 Series: Sub-atmospheric •Metaltometaldiaphragmassures 28" Hg VAC - 15 psig/1 bar Cv=.04 316L SST minimum inboard/outboard leakage 28" Hg VAC - 50 psig/3.5 bar Cv=.30 •Controlssub-atmosphericto 28"HgVAC-100psig/6.9bar positive pressures 28" Hg VAC - 150 psig/10.4 bar •Highflowcapacity •Negativespringbias

BB-3 Miniature

Hydraulic Regulators - Pressure Reducing & Back PressureInlet

Pressure (maximum)


MaterialProduct Series /Features(Pressure Reducing)




50-4000High Pressure

5

54-2800 High Flow/ High Pressure

50-2000 Series: High Pressure/Reducing •Stem&sealdesignedtoextend 10,000, 5-500, 5-800, Cv=.02 316 SST service life in crucial high pressure 15,000 psig 10-1500, 15-2500 Cv=.06 water-based hydraulic applications 690, 1035 bar 25-4000, 50-6000, Cv=.12 •Integral,segregatedand 200-10,000psig Cv=.30 captured venting .35-35, .35-55.2, •Taperedpoppetdesignforbetter .69-103.4,1-172.4 pressure control 14-690 bar

50-2200 Series: High Pressure/Reducing •Designedwithspecialstemandseal 15,000, 300-15,000, Cv=.06 316 SST or to meet the challenges of water- 20,000 psig 300-20,000 psig Cv=.12 Nitronic 60 based fluid applications 1035, 1379 bar 20-1035, •Spring-loaded,wrenchadjustfor 20-1379bar outlet pressures up to 20,000 psig / 1379 bar •Integral,segregatedandcapturedventing 50-4000 Series, 50-4100 Series: High Pressure / Reducing •HydraulicPowerUnits, 10,000, 5500-15,000, Cv = 0.12 315 SST Wellhead Control Panels 15,000 psig 3000-10,000, (Control •Uniqueintegratedbypassvalve 690,1034bar 3000-6000, Regulator) simplifies the high pressure design 3000-4000, Cv = 1.9 system = fewer components and 1100-6000, (Integrated leak paths 1100-4000, Bypass) •Decreasesdowntimeassociatedwith 1100-2500psig filling long umbilicals 380-1034, 207-690, 207-414, 207-276, 76-414, 76-276, 76-172 bar 54-2000 Series: High Pressure/Reducing •Ruggeddesign, 10,000 psig 5-500, 5-800, Cv=.06 300 or high pressure service 690 bar 10-1500, 15-2500, 316 SST •Hardenedmetaltometalseatsfor 25-4000,50-6000, heavy duty service 200-10,000 psig •Systempressuresto20,000psig/ .35-35,.35-55.2, 1379 bar available .69-103.4, 1-172.4 •Integral,segregatedandcapturedventing 1.7-275.8,3.5-414,14-690bar 54-2200 Series: High Pressure •Highflowcapacity:Cv=2.0 8000 psig 5-500, 5-800, Cv=2.0 300 SST •Hardenedmetaltometalseats 10,000psig 10-1500,15-2500, for heavy duty service 552, 690 bar 25-400, 50-6000, •Integral,segregatedand 200-10,000psig captured venting .35-35, .35-55.2, .69-103.4, 1-172.4 1.7-275.8, 3.5-414,14-690 bar 54-2800 Series: High Flow/Reducing •Flowcapacity:Cv=8.0 5000 psig 50-1500, Cv=8.0 300 SST •Inlet&outletpressuresupto 345bar 200-5000psig 5000 psig / 345 bar 3.5-103.4, •Choiceofairratioordomeloading 14-345bar •Hardenedmetaltometalseatsfor heavy duty service •Integral,segregatedandcapturedventing

Corrosion Resistant, Specialty Gas & Petrochemical Regulators

Hydraulic Regulators - Pressure Reducing & Back Pressure

6

44-2200 Compact

04 Miniature/ Lecture Bottle

InletPressure


RangesFlow Capacity Body

MaterialProduct Series /Features(Pressure Reducing)

04 Series: Miniature/Lecture Bottle •Choiceof1/8''or1/4''in&outports 3500 psig 0-30, 0-60, 0-100 psig Cv=.06 Brass or •Minimalinternalvolume 241.3bar 0-2,0-4.1,0-6.9bar 316LSST •Choiceof316SSTorbrass 44-2200 Series: Compact/General Purpose •1/4''inletandoutletports 3500, 1-25,1-50,1-100, Cv=.02 Brass, •Diaphragmsensed-highlysensitive 400psig 2-250,2-500psig Cv=.06 316L SST, • Various trim options available 241.3, .07-1.7, .07-3.5, .07-6.9, Cv=.15 Hastelloy-C ® 27.6 bar .14-17.2, .14-35 bar Cv=.24 or Monel ®

maximum 44-2600 Series: General Purpose/Large Diaphragm •Increasedsensitivity,minimaldroop 3500, 1-25,1-50, Cv=.02 316L SST •Repeatability:±1/2%ofoutlet 400psig 1-100,1-150psig Cv=.06 pressure range 241.3, .07-1.7, .07-3.5, Cv=.15 •Accuracy:±1%ofoutletpressure 27.6bar .07-6.9,.07-10.4bar Cv=.24

56 SeriesFlow Control

InletPressure

(maximum)Outlet

Pressure RangeMaximumFlow Rates

Body Material

Product Series /Features(Pressure Reducing)

56 Series: Flow Control •OffshoreChemicalInjection 15,000 psig 200-15,000 psig 1.20, 0.20, 316 SST or •Accurate,consistentflowcontrol 1034bar 13.8-1034bar 0.16, Nitronic60 reduces risk of over and 2.28 gpm under injection 4.542, 0.7571 •Regulatorlongevityin 0.6057, offshore applications 8.6311 l/m


Material

54-2700 High Flow/Back Pressure

54-2900 SeriesHigh Flow/Back Pressure

Product Series/Features (Back Pressure)

54-2100 Series: Back Pressure/Relief Valve •Accuracy:±1%ofpressurerange 0-500, 0-800, Cv=.08 300 or •Hardenedmetaltometalseats 10-1500,15-2500, 316SST for heavy duty service 25-4000, 50-6000, •Eightpressurerangesupto 200-10,000,300-15,000psig 15,000 psig / 1035 bar .35-35, .35-55.2, .69-103.4, 1-172.4 1.7-275.8, 3.5-414, 14-690, 20.7-1035 bar 54-2300 Series: High Pressure/High Flow - BPR •Controlpressuresto10,000psig/690bar 750, 1500, 3500 Cv=1.6 300 SST •Flowcapacity:Cv =1.6 5000, 10,000 psig •Excellentcracktoreseatratio 51.7,103.4,241.3, • Hardened metal to metal seats 345, 690 bar for heavy duty service 54-2700 Series: High Flow/Back Pressure •Flowcapacity:Cv=5.0 5-500, 50-5500 psig Cv=2.0 300 or •Choiceofdomeloaded,springloaded, .35-35,.35-379bar Cv=5.0 316 SST or air ratio device

54-2900 Series: High Flow/Back Pressure •Controlpressuresupto10,000psig/ 690 bar 500, 1000, 1500, 3000 Cv=5.0 316 SST •Bottomportedoutlet;hardenedmetalto 5000,10,000psig metal seats for heavy duty service 35, 69, 103, 207, •Dome,springloadedandairactuated 345,690bar

44-3400 Two Stage

44-3200 High Flow/Purge

Corrosion Resistant, Specialty Gas & Petrochemical Regulators

7

44-5800 Electric Heated

Vaporizing

SG1 (with accessories)

InletPressure



Product Series/Features(Pressure Reducing)


MaterialProduct Series/Features(Back Pressure)

44-2800 Series: Positive Seal •Mechanical link between diaphragm & 3000 psig 1-25, 1-50, Cv=.16 316L SST main valve prevents pressure creep 207 bar 1-100, 1-150 psig •Positionablecapturedventbonnet .07-1.7,.07-3.5, .07-6.9, .07-10.4 bar

44-3200 Series: High Flow/Purge •Idealpurgeregulator 500, 5-25, 5-50, 5-100, Cv=1.0 Brass or •Highpressureinletversion 3000psig 5-150,5-200psig Cv=1.8 316L SST incorporates a balanced main 35, 207 bar .35-1.7, .35-3.5, .35-6.9, valve to minimize inlet pressure fluctuation .35-10.4, .35-14 bar

44-3400 Series: General Purpose/Two Stage •Decayinginletcharacteristic:.04 3500 psig 2-25, 2-50, 3-100 Cv=.05 Brass or per 100 psig inlet pressure change 241.3 bar 3-150, 3-250 psig 316L SST •Varioustrimoptionsavailable .14-1.7,.14-3.5,.21-6.9, .21-10.4, .21-17.2 bar

44-5000 Series: Absolute Pressure •Controlpressurerange:vacuum 120, 400, 28" Hg Vac to 15 psig/1bar Cv=.06 316L SST to low positive pressures 3500 psig 28" Hg Vac to 25 psig /1.7 bar Cv=.15 8.3, 27.6, 28" Hg Vac to 50 psig /3.5 bar Cv=.24 241.3 bar 28" Hg Vac to 100 psig /6.9 bar

FR 2000 Series: Facilities Regulator •Idealpurgeregulatorforlow 500 psig 0-15, 0-30, 0-75, Cv=1.8 316L SST pressure systems 35 bar 0-150 psig •Negativebiasspringenhances 0-1,0-2,0-5.2, performance at low pressures 0-10.4 bar •Balancedmainvalveminimizes inlet pressure fluctuations

SG Series: SG1 & SG3 Single-Stage, SG2 Two-Stage •316 SST or Neoprene diaphragm - 4500 psig 15, 25, 50, 125, 250 psig Cv=.06 316L SST for increased regulator endurance 310 bar 1, 1.7, 3.4, 8.6, 17.2 bar Cv=.20 & Nickel-plated • 10 micron filter - longer service life Cv=1.0 Brass • Easy to configure with accessories and order • Faster delivery - most ship from stock 44-5800 Series: Vaporizing Regulator • Availableinsteamheated& 6000 psig Up to 500 psig Cv=.02 316L SST, electric heated versions 414 bar 35 bar Monel® or • Superiorheattransfertechnology Hastelloy®

with tolerance to voltage spikes & high ambient temperatures • Optionalheatingcapacityupto400wattsforfasterresponsetoflowvariations • Electricunitdesignedfor115VAC/230VAC,50/60Hz • 4-20mAanalogoutputcapabilityforremotetemperaturemonitoring&dataacquisition • OptionalLCDtemperaturedisplay • T3(200°C)ratingforATEX,IECEx&CSA

44-2300 Series: Back Pressure •Economical,generalpurpose 0-25, 0-50, 0-100, 0-250 psig Cv=.08 Brass or 0-1.7, 0-3.5, 0-6.9, 0-17.2 bar 316L SST

Custom Pressure Reducing & Back Pressure Regulators

Cartridge Regulator (BB Series)

Cartridge Regulators

•Cartridge style externally threaded regulators are designed to be easily installed in a manifold block •Obviousbenefitsinclude:reducedpiping,eliminationofconnections,reducedspace

requirement, ease of service • Canbefurnishedinawidevarietyofpressurereducingorbackpressurestyles • Contactfactoryforapplicationassistance

88

All Pharmpure™ regulators are compliant with the MJ and SF sections of BPE-2009. Clean Service Certification option is available.

PH-1600: Low Pressure, High Flow •FDA Title 21 & USP Class VI Materials 300 psig 1-20, 1-50, Cv=5.0 Brass or 316L SST •Flowsto250SCFMN2 20.7 bar 1-100, 2-300 psig 25 Ra available •Gasandcleansteamversions .07-1.4,.07-3.5, (SSTversiononly) •Portsfrom1/2" - 1 1/2" tube ends, sanitary .07-6.9, .14-20.7 bar

PH-1800: Low Pressure, Very High Flow •FDA Title 21 & USP Class VI Materials 300 psig 1-20, 1-50, Cv=10 Brass or 316L SST •Flowsto1400SCFMN2 20.7 bar 1-100, 2-150 psig 25 Ra available •Gasandcleansteamversions .07-1.4,.07-3.5, (SSTversiononly) •Portsfrom3/4" - 1 1/2" tube ends, sanitary .07-6.9, .14-10.4 bar

Clean Pharmpure™ Regulators for Life Sciences

InletPressure


RangesFlow

CapacityBody

& FinishesRegulator Series /Features

PH-1800 Low PressureVery High Flow

InletPressure


Ranges Flow Capacity Body MaterialProduct Series /Features

20-1000 Series: Compressed Natural Gas •Balancedmainvalveminimizes 3600 psig 0-500 psig Cv=.5 Aluminum inlet pressure fluctuations 248 bar 0-35 bar •Pistonsensed-highlyreliable •Waterheatjacketstandard

20-1200 Series: High Pressure Hydrogen •Nickel-platedaluminum 5000 psig 0-500 psig Cv=.5 Aluminum •Largepistonsensor 345bar 0-35bar 316SST •Allregulatorstamper-proof 20-1400 Series: High Flow /Low Pressure •Diaphragmsensed-highlysensitive 250 psig 0-190 psig Cv=1.6 Aluminum •Domeloadspringbias 17.2bar 0-13bar ±2psig/0.14bar •Capturedbonnetdesignforsafety

Alternative Fuels Regulators


Hydrogen

20-1400 High Flow /

Low Pressure

Custom Pressure Reducing & Back Pressure Regulators

42 MW Welded Diaphragm Instrument Isolator

(shown with the SJS Series regulator)

Differential/Tracking Regulators

• Designedtoprovideacontrolledpressurewhichisthesumofasignal(reference)pressureandabiaspressure (bias can be positive or negative)

• Applicationsinclude:automaticpressurecompensationformechanical(pump)seals,controloffugitive emissions, reduction of breathing gases in commercial or military diving

SJS Series Regulator

• Maintainsaccuratedifferentialpressurewhenincorporatedintoadoublesealsystem • Tracksupsetsinsystempressureanddecreasesdowntimebyincreasingseallife 42 MW Welded Diaphragm Instrument Isolator

• Isolatesandprotectstheregulatorfromcorrosiveprocessmedia • Intendedforusewithourwiderangeoftrackingregulators • Assistsinthecontrolofpressureinfugitiveemissionand/ormechanicalsealsapplications

Air Actuators

• Availableforawiderangeofpressurereducingandbackpressureregulators • Allowsregulatortoberemoteactuatedbyanairsignalfromanexternalairsourceorbyoneof

TESCOM’s electronic controllers • Controlpressuresmayvaryfrom20to20,000psig/1.4to1379bar • Ratiosbetweenactuatorpressureandcontrolpressureareavailablefrom3:1to150:1 • Comparedtoconventionalspringloading,airactuationoffersimprovedregulatorperformance

Air Actuator(26-2000 Series)

All Pharmpure™ regulators are compliant with the MJ and SF sections of BPE-2009. Clean Service Certification option is available.

PH-2200: Compact, Low Pressure, Low Flow •FDA Title 21 & USP Class VI Materials 150 psig 1-10, 1-25, Cv=.06 Brass or 316L SST •Flowsto5SCFMforspecialty 10.4bar 1-50,1-100psigCv=.15 15 or 32 Ra available gas & clean air applications .07-.69, .07-1.7 Cv=.24 (SST version only) •Portsfrom3/8''-1/2" tube ends, sanitary .07-3.5, .07-6.9 bar PH-2600: Compact, Low Pressure, Low Flow •FDA Title 21 & USP Class VI Materials 150 psig 1-10, 1-25, Cv=.06 Brass or 316L SST •Flowsto10SCFMforspecialty 10.4bar 1-50,1-100psig Cv=.15 15 or 32 Ra available gas & clean air applications .07-.69, .07-1.7 Cv=.24 (SST version only) •Portsfrom3/8''-1/2" tube ends, sanitary .07-3.5, .07-6.9 bar PH-3200: Compact, Low Pressure, Medium Flow •FDA Title 21 & USP Class VI Materials 500 psig 5-25, 5-50, Cv=1.0 Brass or 316L SST •Gasandcleansteamversions 35bar 5-100psig Cv=1.8 15 or 32 Ra available •Trackingversionforagitatorseals .35-1.7,.35-3.5, (SSTversiononly) •Gasflowsto50SCFMN2 .35-6.9 bar

Clean Pharmpure™ Regulators for Life Sciences

InletPressure


RangesFlow

CapacityBody

& FinishesRegulator Series /Features

PH-2200 - Low Flow

PH-3200 - Medium Flow

PH-2600 - Low Flow

99

Valves

VT Series3-Way Valve

Operating Pressure(maximum) Flow Capacity

Body MaterialProduct Series/Features

30-1100 Shutoff Valve

VA & VG Air-Operated ON/OFF Valves

VJ BidirectionalShut-off Valve

30 Series: Shutoff Valves •Globeoranglepattern 10,000psig 30-1100globe:Cv=.28 300 SST •Built-inmetallicstopprevents 690bar 30-1100angle:Cv=.49 over-torquing - reduces seat wear 30-1300 globe: Cv=1.57 •30-1100Series:availablewithmetering 30-1300angle:Cv=2.30 capability (long stem optional) 30-1200 globe: Cv=8.0 •Bidirectionalflow(allmodels) 30-1200angle:Cv=10.0 30-1400 globe: Cv=20.0

VA & VG Series: Air Operated ON/OFF Valves •Normallyopenornormallyclosed 6000,10,000 VA:Cv =.75 Brass or •Balancedmainvalve-reduces 15,000, VG:Cv=2.0 316 SST required actuation pressure (30-60 psig) 20,000 psig •Compactpackage 414,690,1035, •Toggleactuatoroptional 1380bar •Solenoidvalveactuation(pneumatic assist) optional

VJ Series: Cartridge Valves •Bidirectionalflow 6000, angle:Cv =.49 Brass or •Built-inmetallicstop 10,000psig globe:Cv =.28 316 SST •Globeoranglepattern 414,690bar •O2 compatible design VL Series: Cv=10 •Balancedmainvalve-reduces 6000psig Cv=10 316 SST required actuation pressure 414 bar •Normallyclosed •In-lineflowconfiguration

VT Series: 3-Way Valve •Highcyclelifeincompactdesign 3500psig Cv=.75 Brass or •3way,2position 6000psig 316SST •Balancedmainvalve 10,000psig •Optionalsolenoidvalve 241.3,414, •Universaloperation 1035bar •ClassVIshut-off

10

Integrated Custom SystemsIntegrated custom systems simplify your pressure, flow & measurement applications. We provide standard designs and custom solutions from the component level and up – capabilities not found with other system integrators. From idea to implementation, whether simple or complex, TESCOM has the expertise to deliver the final product that meets or exceeds your expectations.

Standard ConfigurablePanels/Manifold Blocks

Closed LoopElectronic Control

AutomatedTest Stands

CustomManifold Blocks/Panels

ADVANCEDL E V E L O F I N T E G R A T I O N

ENTRY

CS2200 Changeover System

Changeover Regulators

ACS012 Automatic Changeover

InletPressure


Ranges Flow Capacity Body MaterialProduct Series/Features

ACS012 Series: Automatic Changeover • Eliminatesdowntimecausedby 400, 3500 psig 100, 150, 200, Cv=.06 Brass or depleted gas supplies 27.6, 241.3 bar 250 psig 316L SST • Incorporates44-2200regulators 6.9,10.4,14,17.2bar ACS3200 Series: High Flow Changeover • Highflowcapacity:50scfm 3000 psig 160-200 psig Cv=1.2 Brass or • BasedonTESCOMfield-proven 207bar 11-14bar 316LSST 44-3200 Series Regulator • Eliminates downtime caused by depleted gas supplies

CR441800 Series: High Pressure Changeover • Inletpressuresupto6000psig 3500, 5-500,5-600, Cv=.06 Brass or • BasedonTESCOM’sfieldproven 6000psig 10-700,10-800, 316LSST 44-1800 Series Regulator 241.3, 10-900, 10-1,000 psig • Eliminatesdowntimecausedby 414bar .35-35,.35-41.4,.69-48.3, depleted gas supplies .69-55.2, .69-62, .69-69 bar CS-2200 Series: Changeover System • Eliminatesdowntimecausedby 3500psig 0-25,0-50,0-100, Cv=.06 Brass or depleted gas supplies 241.3 bar 0-150 psig 316L SST • Singlebodychangeoverregulator 0-1.7,0-3.5,0-6.9, plus a point-of-use regulator 0-10.3 bar • Incorporates44-2200regulators

NA-4 Series: Changeover System • Includes changeover & line regulator, 3000 psig 30, 50, 100, 150, Cv=.06 Brass or cylinder, vent & outlet shutoff valves 200, 300, 500, 316L SST • Highpressurelineregulatorsupto 750,1000,1500psig 1500 psig 2, 3.5, 6.9, 10.3, • Supportsuptoeightcylindersperside 13.8, 20.7, 35, • Optionalremotemountannunciator 51.7, 69, 130.5 bar

Auto Cascade System • Automaticoperationandpriorityfill • 10,000psig/690barmaximumoperatingpressure

NA-4 Changeover System

Auto Cascade System • Simultaneouslychargeanddispense• Cartridgeservicingforeasymaintenance

11

ER5000 Digital Pressure Controller

ER5100 SeriesHigh Flow Control

ER5K KitPanel Assembly

Pressure Reducing

Electronic Pressure Controls

ER5000 Series Digital Pressure Controller

• Preciseaccuracy:±.1%FSO! • Featurescontrolledoutletpressurefrom0-100psig/0-6.9barasastandaloneunit • Compatibleprandessureregulatorsavailableofferingvacuumto20,000psig/1379barcontrol • Selectablesetpointsignalsource: – External analog, digital USB or RS485, downloadable profile • Selectablefeedbacksignalsource: – Internal 0-100 psig / 0-6.9 bar sensor or external analog • NEMA4Xenclosure • CE,CSA,IECExandATEXapproved • Twoenhancedversions,ER5000FIandFV,offeradditionalanalog/digitalinputsandconditional control profile segments, IF and GOTO, allowing the user even more sophisticated control. These models also include analog sensor output and "Suspend Control" mode which suspends the control algorithm and locks outlet pressure to ensure total stability. • Freetuningandinterfacesoftwareprovided • RS485convertersandpowersuppliesalsoavailable • Stainlesssteeloption

ER5K Kits

ER5000 Pressure Reducing and Backpressure kits are engineered to provide all the equipment needed to get your pressure control system up and running with minimum effort on your part. • Noguesswork-everythingyouneedispre-assembledontoapanelormountedwithinanenclosure • Savestime,moneyandheadaches • Tunedandtestedbeforedelivery

Kits include: • ER5000FI-1 • Pressurereducingorbackpressureregulator • 4-20mAfeedbacktransducer • ERsupplyregulator(optional) • Allconnectionsandfittings • ERjunctionbox(optional) • Documentationpackage

ER5040 Series

• FeaturesoftheER5000withOEMbase,nocover • NotavailableinExplosion-Proof ER5000/26-2000 Series - High Accuracy, High Pressure Control

• Designedforapplicationswherehighaccuracyandreliabilityarecritical • Choiceofoutletpressurerangesto20,000psig/1379bar • Excellentforcalibrationsystems ER5020 Series - High Pressure, Low Flow Integrated Systems

• Integrates with 26-1000 Dual Piston Regulator to achieve 10-9000 psig / 0.69-620 bar in 395 milliseconds • Choiceofoutletpressurerangesto10,000psig/690bar • Gasorliquidapplications • Segregatedventing • Flowcapacity:Cv=0.06 • Otherintegratedregulatorsavailable

ER5100 Series - High Flow Control

• Integrateswith44-4000ventingregulator • Choiceof500or900psig/35or62baroutletranges • Flowcapacity:Cv=0.7 or 2.0 • Availableinbrassorstainlesssteel

ER5040 Series

ER5000 / 26-2000 Series

ER5040 Series

12

Electronic Pressure Controls

269-529 Low Pressure/High Flow Regulator

ER5110 Compact Integrated Unit

ER5110 Series - Compact Integrated Unit

• Integrateswith44-5200regulator,standardoptionsavailable • FeaturesidenticaltotheER5000(shownonpage11) • Choiceofoutletpressurerangesto500psig/35bar • Referencepressure:100psig/6.9bar • Flowcapacity:Cv=0.06 or 0.15 • Ventingornon-venting

269-529 Series - Low Pressure/High Flow Pressure Regulator

• Maximuminletpressure:300psig/20bar • Controlledoutletpressureto100psig/6.9bar,somemodelsupto300psig/20bar • Portsfrom1/4"to2-1/2" • Flowcapacity:Cv values up to 45 • Exceptionallowpressurecontrolthroughoutflowrange

70-2000 Series Motorized Actuator

• 24VDCmotorizedactuatorprovidesremoteadjustmentofregulatorsetpoint •Adaptableto26-1000,26-1600,26-1700,26-2300,54-2000and54-2100SeriesRegulators • Variablespeedcontrolwithadjustablelimitstopstopreventover-travel

Pressure Transducers

• IdealforuseinER5000applicationswhereanexternalfeedbackisrequired •Providesextremelystableandrepeatablehydraulicandpneumaticpressuremeasurements •.1%,0.25%and0.5%accuracyavailable • Choiceof4-20mA,0-10VDCversions • Widechoiceofpressureranges(includingsub-atmospheric)

70-2000 Motorized Actuator

Operating Pressure(maximum)

Body MaterialProduct Series/Features

Accessories

Gauges

Mini In-Line Filters98 Series

Pressure Gauges (2'' & 2.5''dia.) • BrassorStainlessSteelconstruction sub-atmosphericto Brassor316SST • Pressurerangesfromsub-atmospheric 10,000psig/690bar to 10,000 psig / 690 bar • 1/4"connections

Filters - High Pressure (10 micron) • 98-1010SeriesMiniIn-Linefilter: 6,000psig 304SST •Forsystemswithsizelimitations 414bar • 98-1110SeriesT-TypeFilter: 6,000,10,000psig 300SST •Designedforhighflowapplications 414,690bar •Featurescleanableelement •Availableoptions:electrical,visual, bypass valve, visual pressure differential indicator, bypass relief valve, electrical bypass • 98-1210SeriesIn-LineFilter: 3,000,6,000, 300and17-4SST •Forsystemswithsizelimitations 10,000psig •Cleanableelement 207,414,690bar

TESCOM™ designs and manufactures a wide range of standard and custom engineered pressure control solutions for a diverse world market. Whether your needs are components like regulators and valves or pressure systems and assemblies, TESCOM provides expert application and customer support from simple industrial applications to high tech complex projects. Market application know-how includes Aerospace & Defense, Alternative Fuels, Diving & Life Support, Laboratory & Research, Life Sciences, Medical, Oil & Gas and Microelectronics to name just a few.

TESCOM distributor support centers are located in most major cities worldwide providing application assistance and quality TESCOM product.

TESCOM sales offices are located in the USA, United Kingdom, Germany, Singapore, South Korea and United Arab Emirates.

For a distributor or sales office location near you, visit www.tescom.com and click on the Sales and Support Contacts link.

TESCOM Manufacturing & Distributor Network... a worldwide presence!

NORTH AMERICAElk River, Minnesota USA

EUROPESelmsdorf, Germany

ASIA PACIFICPudong Shanghai, China

13

Manufacturing SiteSales Office

An ISO 9001 Quality System Certified Company

METI Certified Self-Inspecting ManufacturerMAB 491-N

The contents of this publication are presented for information purposes only, and while effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by our terms and conditions,whichareavailableonrequest.Wereservetherighttomodifyorimprovethedesignsorspecificationsofourproductsatanytimewithoutnotice.

We are your worldwide partner in precision pressure control.

DBROC1753X012©2016Emerson Process Management Regulator Technologies, Inc. All rights reserved. Printed in the U.S.A. 1/16. Tescom, Emerson Process Management, and the Emerson Process Management design are marks of one of the Emerson Process Management group of companies. All other marks are the property of their respective owners.

Emerson Process Management Regulator Technologies, Inc.

Americas

TESCOM12616 Industrial BoulevardElk River, Minnesota 55330-2445 USAT: +1 800 447 1250T: +1 763 241 3238F: +1 763 241 3224E: [email protected]

Continental Europe

TESCOMAn der Trave 23-2523923 Selmsdorf, GermanyT: +49 38823 31 287F: +49 38823 31 140E: [email protected]

Asia-Pacific

TESCOM3/F, Building #2No.1277,XinJinQiaoRoadJinqiaoE.P.ZPudong Shanghai, 201206 ChinaT: +86 21 2892 9000F: +86 21 2892 9001E: [email protected]

Middle East and Africa Emerson FZEP.O. Box 17033JebelAliFreeZone-South(Zone2)Dubai, United Arab EmiratesT: +971 4 811 8443F: +971 4 811 8987E: [email protected]

For further information visit www.tescom.com

We are your worldwide partner We are your worldwide partner in precision pressure control.in precision pressure control.

Ultra-high purity pressure controls are available. These products are designed for semiconductor, flat panel displays, photovoltaic and other microelectronic applications.

regulators, valves & systems - · pdf filehigh pressure - pressure reducing regulators...

Documents