quinn therm limited ippc no p0739-01 annual … · environmental manual- annual environmental...

Quinn Therm Ltd

Environmental Manual- Annual Environmental Report

Submitted March 2011

Issue No 04

Prepared by Neil Martin

Annual Environmental

Report

Quinn Therm Limited

IPPC No P0739-01

Annual Environmental Report

2011

Quinn Therm Ltd



Issue No 04



Report

AER P0739-01 Contents: 1.0 Company Details........................................................................................3

1.1 Process Overview: .......................................................................................................4 2.0 Overview ..................................................................................................5 3.0 Environmental Management .................................................................6

3.1 Progress Meetings .......................................................................................................6 4.0 Environmental Objectives and Targets ............................................................8 5.0 Emissions.................................................................................................9

5.1 Emissions from the installation .................................................................................9 5.2 Emissions to Atmosphere and Sewer.......................................................................9 5.3 Emissions to Water......................................................................................................9 5.4 Pollution Emissions Register...................................................................................10 5.5 Waste Management....................................................................................................10 5.6 Recycling & REPAK ...................................................................................................10 5.7 Water Usage................................................................................................................10 5.8 Energy Usage..............................................................................................................11

6.0 Environmental Performance........................................................................12 6.1 Annual Reporting .......................................................................................................12

6.1.1 Noise Monitoring Report Summary ...........................................................12 6.1.2 Ambient Monitoring Summary ..............................................................12 Table 1.0 ...................................................................................................13 6.1.3 Air Emissions Monitoring Summary.......................................................14 Table 2.0 ...................................................................................................14

6.2 Resource Consumption Summary ..........................................................................15 Table 3.0 ...................................................................................................15

6.3 Complaints Received.................................................................................................15 6.4 Wastes off Site............................................................................................................15 6.5 Notifications and Reported Incidents to the Agency during 2010......................16 6.6 Tank and pipeline testing..........................................................................................16 6.7 Risk Mgt Programmes ...............................................................................................16

7.0 Environmental Management Programme .......................................................17 7.1 Residual Management Plan .......................................................................................17 7.2 ELRA ............................................................................................................................17 7.3 Bund Integrity .............................................................................................................17 7.4 Environmental Prevention Measures and Remedial Actions..............................18

Quinn Therm Ltd



Issue No 04



Report

1.0 Company Details Company Name: Quinn Therm Limited Licence Register Number: P0739-01 Address: Scotchtown, Ballyconnell, Co. Cavan Managing Director Paddy Mohan Divisional Manager Joseph Donegan Contact Numbers: Phone 049 9525600 Fax 049 9525601

Quinn Therm Ltd



Issue No 04



Report 1.1 Process Overview: Quinn Therm Ltd is located in Scotchtown, Ballyconnell, Co. Cavan. It manufactures Polyioscyanurate board for the construction Industry. The combination of technology and chemistry lends itself to the creation of an insulation board which has zero ODP, low thermal conductivity, high insulation value with class 1 fire rating surface spread of flame. Cost-effective and environmentally sensitive solutions are a strong feature of the company. Its products do not readily absorb water, making them suitable for use in damp environments. They are also light, robust and easy to handle. All products are manufactured to withstand the service life of a building. The process consists of a main production area, laboratory, dust extraction, chemical blending and storage areas, raw material and final product storage, pentane tank storage, off loading area, spray cage, offices, toilets and car parking facilities.

Quinn Therm Ltd



Issue No 04



Report

2.0 Overview Quinn Therm Ltd is located in Scothchtown, Ballyconnell, Co. Cavan. This annual environmental report summarises the environmental performance for the year Jan 2010 – December 2010. This report has been compiled in accordance with the EPA Guidance note for an annual environmental report, using template spreadsheets from the Office of Environmental Enforcement. During 2010, the company strived to improve compliance with conditions in its IPPC licence while also maintaining its ISO 14001:2004 accreditation.

Quinn Therm Ltd



Issue No 04



Report

3.0 Environmental Management The Divisional Manager is responsible for the implementation of the Environmental Policy, overall environmental management of the site and allocation of resources. Designated EHS Officers are responsible for the day-to-day operations of the site, and the management of the IPPC licence. The Ground Staff are responsible for the day-to-day operation of the installation and implementing good environmental practice and training. Environmental communication is essential to the Quinn Therm Ltd ethos and as such Quinn Therm Ltd communicates any environmental issues to its staff, via meetings, memos, notice boards, presentations etc. Applicable Documents Quinn Therm Ltd Environmental Organizational Chart (See Page 7)

3.1 Progress Meetings Production progress meetings are carried out weekly, where environmental issues are also addressed. Dedicated Environmental Meetings are held monthly to discuss improvements, actions in progress, environmental management programs, objectives and targets, waste management issues/ controls and to discuss environmental audits, energy management etc. This meeting is attended by the divisional manager, plant manager, production manager, polymer engineering manager and quality systems supervisor along with the Quinn Group’s environmental management department. Information is passed on to significant team members as appropriate. Any issues, improvements or comments from members of staff regarding environmental performance were communicated through the system and acted upon.

Quinn Therm Ltd



Issue No 04



Report

Director Paddy Mohan

Divisional Mgr Joseph Donegan

Group H&S Mgr Brendan O Neil

Office Manager Sinead Casey

Sales Manager Rose Mullally

Sales UK Leo Mc Elgunn

Production Mgr Peadar Maguire

P. Eng Mgr UK&Irl HSE Officer /Mgt Rep

Aine Osojca (Acting Neil Martin)

Office Supervisor Charlene Mc Kiernan

Production Supervisors Terry Mc Govern /

Darren Murphy

Operators Office Staff Group Junior H&S Advisor

Imelda Kelly

Dispatch Kevin Mc Barron

Lorry Drivers

Group Depts. IT, HR, Technical

Sales, Stores

Group Environmental.Mgr

Fintan Coyle

Maintenance Dept Gordon Wiggins /

Barry Owens

Plant Mgr Norman Whyte

Warehouse Supervisor/

Production Planner Vincent Costello

Quality Supervisor HSE Officer/Mgt Rep

Joanne Willis

FLT Drivers

Group Environmental Advisor

Stephen Linden

EHS Representative Terry Mc Govern

Quinn Therm Ltd



Issue No 04



Report

4.0 Environmental Objectives and Targets Environmental Objectives and Targets were revised upon in September 2010 following the annual environmental review, with Quinn Therm being reviewed on a monthly basis at the environmental meeting in conjunction with the Quinn Group’s environmental management team. Objectives and Targets are focussed on the environmental aspects which Quinn Therm Ltd have influence over and which would have a significant impact on the environment. Applicable Documents: Environmental Objectives and Targets

Environmental Management Programs

Quinn Therm Ltd



Issue No 04



Report

5.0 Emissions 5.1 Emissions from the installation Independent monitoring of plant emissions is carried out by QED Engineering, Monaghan. Cyclones and bag filters are used in the dust extraction system to reduce particulate emissions from the installation. 5.2 Emissions to Atmosphere and Sewer All activities on site are carried out responsibly to ensure that there were minimal odours or air emissions released from the site. There are now four emission points to air from the production process each with individual emission limit values set out by the EPA. The fourth emission point, located at the plasterboard assembly point (A2-4), was added in early 2010. The agency was informed about this new emission point in March 2010. No process effluent is generated from activity of the plant. The waste from the toilets and the canteen are released into the site sewerage system which is pumped to the local wastewater treatment plant. The emissions to sewer are domestic in nature and do not require a discharge licence and is exempt from monitoring. 5.3 Emissions to Water There are no emissions to water of environmental significance from the plant. Storm water emissions were inspected weekly for odour and colour by Quinn Therm staff and samples were taken and analysed by Euro Environmental Services Ltd for pH and COD quarterly and total suspended solids on a quarterly basis.

Quinn Therm Ltd



Issue No 04



Report

5.4 Pollution Emissions Register Quinn Therm Ltd do not emit any of the chemicals listed on the PRTR reporting list, therefore no report for the year has been completed, as of the revised reporting online spreadsheets devised by the Agency. 5.5 Waste Management The company has a number of waste streams arising on site that were recovered or disposed of offsite, please refer to spreadsheet attached All wastes were collected and disposed of by approved and licensed contractors, which are periodically audited by Quinn Therm Ltd. Waste Removed 2010

5.6 Recycling & REPAK Where possible, all waste packaging from the production floor is recycled. Quinn Therm recycles wood, baled plastic, plastic drums, baled cardboard, cardboard cores, steel and paper. Quinn Therm subscribes to REPAK, which involves declaring the amount of packaging waste on our products sold within the Republic of Ireland. A bi-annual fee is then paid to REPAK based upon the waste quantities declared. The amount of recycled waste has decreased in 2010 due to a focus on suppliers to reduce the amount of packaging that was send into us. This was also helped by Quinn Therm replacing wooden pallets with polystyrene skids. 5.7 Water Usage Water usage analysis is carried out on a monthly basis. Analysis is made with regards to volume of water used against working hours. This report is sent to the Group’s Environmental Manager and reviewed at the monthly environmental meetings. Any abnormalities from this report will lead to an investigation being carried out and corrective actions issued if required. There were no significant issues within 2010.

Quinn Therm Ltd



Issue No 04



Report

5.8 Energy Usage Energy usage for the year 2010 was analysed on a monthly basis, there are dedicated energy management programs in place in Quinn Therm Ltd, which are designed to reduce the amount of energy used on the Therm Ltd site. Therm Ltd uses the SEI Energy Tracker as a tool to aid with energy management. An energy audit was carried out during 2010, a copy of which is available on-site. All monthly analysis is reviewed at the monthly environmental meeting and any abnormalities are discussed and corrective actions issued if required. In a bid to reduce fuel consumption, a new boiler has been installed in the main office area. All relevant information regarding the new boiler was submitted to the EPA in December 2010. Reference: Energy Management Programs

Quinn Therm Ltd



Issue No 04



Report

6.0 Environmental Performance 6.1 Annual Reporting Reports were submitted to the agency in full and to the specifications laid out in the IPPC licence.

6.1.1 Noise Monitoring Report Summary A day and night noise survey of the plant was carried out by QED Engineering Ltd, October 2010. Five monitoring points were located for the day-time and night-time noise survey. Due to Quinn Therm Ltd being situated between two other industrial sites and across a busy road (R205 / B127) from a cement manufacturing plant it is extremely hard to distinguish noise sources. NSL1 is situated particularly close to the Quinn Packaging plant and NSL3 is in close proximity to the Quinn Cement plant. NSL5 is the nearest noise location to the Therm Ltd plant and the readings at this location both day and night were well within limits set in the IPPC licence. Therefore it can be assumed that all noise exceedances are attributed to other factors within the vicinity of Quinn Therm Ltd. No complaints relating to noise have been issued to the company in 2010. Three copies of this report were furnished to the EPA.

1. Rakeelan filling Station/Shop NSL2 2. Cassidy’s Shop NSL1 3. McKiernan’s Residence NSL 3 4. Doon Heights NSL 4 5. River Bank NSL 5

6.1.2 Ambient Monitoring Summary Groundwater monitoring wells are located on site under condition 3.12 of the IPPC licence 739. Samples for storm water were taken and sent to QED Engineering for evaluation on behalf of the EPA. Ground water is annually tested and storm water is quarterly tested. Quinn Therm Ltd

Quinn Therm Ltd



Issue No 04



Report

ground water tests and storm water tests were carried out by QED Engineering & Euro Environmental Services Ltd., respectively. All results are within the guidelines. Below are the most recent results from monitoring. Ground Water

Table 1.0

Date Parameter Units Results GWS1-B

Results GWS-3

Results GWS-4

November 2010 pH pH units 7.5 7.6 7.6

COD mg/l 8 8 8

Conductivity S/cm 400 437 345 VOCs g/l N.D N.D N.D

Storm Water Table 1.1

Date Parameter Units Results 29/03/2010 pH pH units 8

COD mg/l 5

Suspended Solids mg/l 2 Date Parameter Units Results

17/06/2010 pH pH units 8

COD mg/l 10

Suspended Solids mg/l 2

Date Parameter Units Results 06/10/2010 pH pH units 7.4

COD mg/l 5


Date Parameter Units Results 29/12/2010 pH pH units 7.6

COD mg/l 5


Quinn Therm Ltd



Issue No 04



Report

6.1.3 Air Emissions Monitoring Summary Five emission points are located on site to monitor emissions to atmosphere as per schedule C.1 (ii) of the licence. This work was carried out by QED Engineering in September 2010. Results from this report state the combustion efficiency of the boilers is high and all emission results are within the IPPC Emission Limit Values. Air Emissions monitoring results

Table 2.0

Date Parameter Substance to be monitored

Units Limit

emissions Results

June 2010 A1-2 (a) Boiler Combustion

efficiency mg/Nm3 ----- 91.3%

A1-2 (b) Combustion

efficiency mg/Nm3 Must be high 90.3%

A2-1 (Dust

extraction System) Particulates

Test 1 mg/Nm3 10 1.7

Particulates

Test 2

1

A2-2 (Chemical

Laydown Extraction system)

MDI mg/Nm3 0.1 <0.004

A2-3 (Pentomat

Extraction System)

MDI mg/Nm3 0.1 <0.007

A2-4 (Extraction

System) MDI mg/Nm3 0.1 <0.004

Date Parameter Substance to be monitored

Units Limit

emissions Results

September 2010 A1-2 (a) Boiler Combustion

efficiency mg/Nm3 ----- na

A1-2 (b) Combustion

efficiency mg/Nm3 Must be high na

Quinn Therm Ltd



Issue No 04



Report

A2-1 (Dust

extraction System) Particulates

Test 1 mg/Nm3 10 1

Particulates

Test 2 2

A2-2 (Chemical

Laydown Extraction system)

MDI mg/Nm3 0.1 <0.008

A2-3 (Pentomat

Extraction System)

MDI mg/Nm3 0.1 <0.006

A2-4 (Extraction

System) MDI mg/Nm3 0.1 <0.004

6.2 Resource Consumption Summary The following table summarises the volumes of fuel and electricity purchased and utilised at Quinn Therm Limited during January 2010 to December 2010.

Table 3.0 Resource Amount Electricity 1,716,907.14 kWh

Fuel for heating 265,550 Litres Fuel for fork trucks 36,517 Litres

6.3 Complaints Received There were no complaints received at the plant regarding operations at the plant in 2010. 6.4 Wastes off Site All wastes that are transported off site are recorded as per requirements of IPPC licence. This includes the tonnage of waste produced, destination of waste, name of transporters and the EWC code. All waste contractors used by Quinn Therm Ltd have obtained the required permits and licences. All hazardous waste is disposed of in the correct manner by approved

Quinn Therm Ltd



Issue No 04



Report

contractors. Waste contactors are periodically audited with regards their permits and how they carry out the removal of the waste. 6.5 Notifications and Reported Incidents to the Agency during 2010. One incident (involving a minor fire) was reported to the Agency in January 2010. All related corrective actions to this incident are now closed out. Minor incidents are recorded internally as of the recording requirements of ISO 14001, but these incidents had no potential for risk to the wider environment that would necessitate communication to the Agency. 6.6 Tank and pipeline testing As part of the preventative maintenance plan in Quinn Therm Ltd, pipe work, tanks, chemical storage area etc are inspected on a daily/weekly basis for any leaks pressure changes any abnormalities. All issues are documented and kept on file. The underground pentane tank is connected to an alarm sensor, in the case of a pressure drop the alarm will sound and the line will cut out. This alarm system is checked periodically by an approved contractor. 6.7 Risk Mgt Programmes All high risk management programs were closed out in 2010. Currently there are no risk management programs in place; this is going to be reviewed at the annual environment management review to see if status has changed.

Quinn Therm Ltd



Issue No 04



Report

7.0 Environmental Management Programme A proposal for the current year running from Jan 2010 to Dec 2010 was decided upon in Jan 2010 and again reviewed at the environmental management review meeting. These are ongoing with review at the monthly environmental management meeting to view status. Refer to environmental management programs. Applicable Documents: Environmental Management Program

7.1 Residual Management Plan The residual management plan was originally submitted in March 2007 to the EPA for approval. Quinn Therm Ltd reviewed this ERLA in August 2010. A copy of this reviewed document is kept on file at Quinn Therm Ltd. No significant changes have been made to this document. 7.2 ELRA The ELRA was submitted to the agency during the year 2007 and reviewed in August 2010. A copy of this reviewed document is kept on file at Quinn Therm Ltd. No significant changes have been made to this document. 7.3 Bund Integrity Permanent bunds are checked by an external agency (Adcon Consultants Ltd, Belturbet, Co. Cavan) every 3 years, as per IPPC licence requirements. Reports are kept on file at Quinn Therm Ltd. Next external check is due in July 2011. Visual checks are carried out internally on all mobile bunds with the relevant reports being kept on file at Quinn Therm Ltd.

Quinn Therm Ltd



Issue No 04



Report

7.4 Environmental Prevention Measures and Remedial Actions Quinn Therm Ltd has maintained ISO 14001:2004 certification of the site EMS for the duration of 2010, as well as maintaining an operation EMS system. The following actions have been carried out in 2010 in order to ensure the successful operation of the EHS Management System in accordance with the IPPC licence and ISO14001:2004

Environmental Aspects were reviewed and updated to reflect production activities.

Waste Management practices are in place in Quinn Therm Ltd, only approved contractors are used.

Environmental issues are discussed at the weekly progress meeting and also at the monthly environmental meeting.

Energy management system in place, targets were given for energy reduction. These targets are reviewed on a monthly basis.

Evacuation Drills are carried out on all shifts bi-annually and results are evaluated so that corrective actions can be put in place.

Training to be given to employees in terms of Fire training and chemical spill training. Moving forward regular external audits will be carried out to ensure that the EMS and ISO 14001:2004 are implemented, maintained and is operational throughout the plant. Recertification for ISO 14001: 2004 will take place during early 2011. Quinn Therm Ltd has an ongoing commitment to ensure that all operations are carried out in an environmentally friendly way and that the aspects are controlled and monitored in order to assess environmental improvements on an ongoing basis. In 2011, special focus will be on energy reduction and ensuring that the bund tank integrity testing is conducted in July 2011, as per the IPPC licence. As per new guidelines received from the EPA in October 2010, any contractor carrying out air monitoring for Quinn Therm will be requested to prove their accreditation status against ISO 17025, otherwise they will need to provide competency records. Supporting documents will be included in future AER reports.

| PRTR# : P0739 | Facility Name : Quinn Therm Limited | Filename :

P0739_2010.xls | Return Year : 2010 | 4840 19/04/2011 11:17

Guidance to completing the PRTR workbook

Version 1.1.11

REFERENCE YEAR 2010

1. FACILITY IDENTIFICATION

Parent Company Name Quinn Therm Limited

Facility Name Quinn Therm Limited

PRTR Identification Number P0739

Licence Number P0739-01

Waste or IPPC Classes of Activity

No. class_name

5.12(d)

nitrogenous hydrocarbons such as amines, amides, nitrous

compounds, nitro compounds or nitrate compounds, nitriles,

cyanates, isocyanates

Address 1 Quinn Therm Limited

Address 2 Scotchtown

Address 3 Ballyconnell

Address 4 Co. Cavan

Country Ireland

Coordinates of Location -7.57006 54.1262

River Basin District GBNIIENW

NACE Code 2014

Main Economic Activity Manufacture of other organic basic chemicals

AER Returns Contact Name Joseph Donegan

AER Returns Contact Email Address [email protected]

AER Returns Contact Position Divisional Manager

AER Returns Contact Telephone Number 049952 5604 number

AER Returns Contact Mobile Phone Number

AER Returns Contact Fax Number 0490 9525601

Production Volume 0.0

Production Volume Units

Number of Installations 1

Number of Operating Hours in Year 4200

Number of Employees 46

User Feedback/Comments na

Web Address

AER Returns Workbook

Web Address

2. PRTR CLASS ACTIVITIES

Activity Number Activity Name

4(a)(iv)

Nitrogenous hydrocarbons such as amines, amides, nitrous

compounds, nitro compounds or nitrate compounds, nitriles,

cyanates, isocyanates

3. SOLVENTS REGULATIONS (S.I. No. 543 of 2002)

Is it applicable? No

Have you been granted an exemption ? No

If applicable which activity class applies (as per

Schedule 2 of the regulations) ? na

Is the reduction scheme compliance route being

used ? na

4.1 RELEASES TO AIR Link to previous years emissions data | PRTR# : P0739 | Facility Name : Quinn Therm Limited | Filename : P0739_2010.xls | Return Year : 2010 | 19/04/2011 11:17

8 8 16 16 24 25 6 6 6 6 6 8 25

SECTION A : SECTOR SPECIFIC PRTR POLLUTANTS

Please enter all quantities in this section in KGs

QUANTITY

No. Annex II Name M/C/E Method Code Designation or Description Emission Point 1 T (Total) KG/Year A (Accidental) KG/Year F (Fugitive) KG/Year

0.0 0.0 0.0 0.0

* Select a row by double-clicking on the Pollutant Name (Column B) then click the delete button

SECTION B : REMAINING PRTR POLLUTANTS


QUANTITY


0.0 0.0 0.0 0.0


SECTION C : REMAINING POLLUTANT EMISSIONS (As required in your Licence)


QUANTITY

Pollutant No. Name M/C/E Method Code Designation or Description Emission Point 1 Emission Point 2 Emission Point 3 T (Total) KG/Year

A (Accidental)

KG/Year

F (Fugitive)

KG/Year

322 MDI as NCO group M ALT

MDHS (Method for the

Determination of Hazardous

Materials) 25/3 Organic

Isocyanates in Air 0.147 0.1218 0.0525 0.3213 0.0 0.0

210 Dust M ALT ISO EN 13284-1 432.39 268.38 0.0 700.77 0.0 0.0


Additional Data Requested from Landfill operators

Landfill: Quinn Therm Limited

Please enter summary data on the

quantities of methane flared and / or utilised

additional_pollutant_no T (Total) kg/Year M/C/E Method Code

Designation or

Description

Facility Total Capacity m3

per hour

Total estimated methane generation (as per

site model) 0.0 N/A

Methane flared 0.0 0.0 (Total Flaring Capacity)

Methane utilised in engine/s 0.0 0.0 (Total Utilising Capacity)

Net methane emission (as reported in Section A

POLLUTANT METHOD

Method Used

For the purposes of the National Inventory on Greenhouse Gases, landfill operators are requested to provide summary data on landfill gas (Methane)

flared or utilised on their facilities to accompany the figures for total methane generated. Operators should only report their Net methane (CH4)

emission to the environment under T(total) KG/yr for Section A: Sector specific PRTR pollutants above. Please complete the table below:

Method Used

Method Used

RELEASES TO AIR

POLLUTANT METHOD

Method Used

POLLUTANT

RELEASES TO AIR

RELEASES TO AIR

METHOD

Net methane emission (as reported in Section A

above) 0.0 N/A

4.2 RELEASES TO WATERS Link to previous years emissions data | PRTR# : P0739 | Facility Name : Quinn Therm Limited | Filename : P0739_2010.xls | Return Year : 2010 | 19/04/2011 11:17

8 8 16 16 24 24 6 6 6 6 6 6 24

SECTION A : SECTOR SPECIFIC PRTR POLLUTANTS Data on ambient monitoring of storm/surface water or groundwater, conducted as part of your licence requirements, should NOT be submitted under AER / PRTR Reporting as this only concerns Releases from your facility


QUANTITY


0.0 0.0 0.0 0.0


SECTION B : REMAINING PRTR POLLUTANTS


QUANTITY


0.0 0.0 0.0 0.0


SECTION C : REMAINING POLLUTANT EMISSIONS (as required in your Licence)


QUANTITY

Pollutant No. Name M/C/E Method Code Designation or Description Emission Point 1 T (Total) KG/Year A (Accidental) KG/Year F (Fugitive) KG/Year

ALT 0.0 0.0 0.0 0.0


RELEASES TO WATERS

RELEASES TO WATERS

Method Used

POLLUTANT

Method Used

POLLUTANT

POLLUTANT

RELEASES TO WATERS

Method Used

4.3 RELEASES TO WASTEWATER OR SEWER Link to previous years emissions data | PRTR# : P0739 | Facility Name : Quinn Therm Limited | Filename : P0739_2010.xls | Return Year : 2010 | 19/04/2011 11:17

8 8 16 16 6 6 6 6

SECTION A : PRTR POLLUTANTS


QUANTITY


0.0 0.0 0.0 0.0


SECTION B : REMAINING POLLUTANT EMISSIONS (as required in your Licence)


QUANTITY

Pollutant No. Name M/C/E Method Code Designation or Description Emission Point 1 T (Total) KG/Year A (Accidental) KG/Year F (Fugitive) KG/Year

0.0 0.0 0.0 0.0


OFFSITE TRANSFER OF POLLUTANTS DESTINED FOR WASTE-WATER TREATMENT OR SEWER

OFFSITE TRANSFER OF POLLUTANTS DESTINED FOR WASTE-WATER TREATMENT OR SEWER

Method Used

Method Used

POLLUTANT METHOD

POLLUTANT METHOD

5. ONSITE TREATMENT & OFFSITE TRANSFERS OF WASTE | PRTR# : P0739 | Facility Name : Quinn Therm Limited | Filename : P0739_2010.xls | Return Year : 2010 | 19/04/2011 11:17

5 10 Please enter all quantities on this sheet in Tonnes 0

Quantity

(Tonnes per

Year)

Haz Waste : Name and

Licence/Permit No of Next

Destination Facility Non

Haz Waste: Name and

Licence/Permit No of

Recover/Disposer

Haz Waste : Address of Next

Destination Facility

Non Haz Waste: Address of

Recover/Disposer

Name and License / Permit No. and

Address of Final Recoverer /

Disposer (HAZARDOUS WASTE

ONLY)

Actual Address of Final Destination

i.e. Final Recovery / Disposal Site

(HAZARDOUS WASTE ONLY)

Transfer Destination

European Waste

Code Hazardous Quantity T/Year Description of Waste

Waste

Treatment

Operation M/C/E Method Used

Location of

Treatment Name and Licence / Permit No. of Recoverer / Disposer / Broker Address of Recoverer / Disposer / Broker Name and Address of Final Destination i.e. Final Recovery / Disposal Site (HAZARDOUS WASTE ONLY) Licence / Permit No. of Final Destination i.e. Final Recovery / Disposal Site (HAZARDOUS WASTE ONLY)

Within the Country 20 03 01 No 26.28 mixed municipal waste D1 M Weighed Onsite in Ireland

Monaghan County

Council,W0020-02

Scotch Corner

Landfill,Letterbane,Castlebla

ney,Co. Monaghan,Ireland

Within the Country 15 01 03 No 8.12 broken wooden packaging R3 M Weighed Onsite in Ireland

Wilton Waste,WCP MH-08-

0057-01

Kiffa,Crosslerlough,.,Co.Cav

an,Ireland

To Other Countries 15 01 01 No 3.48 paper and cardboard packaging R3 M Weighed Abroad


0057-01


an,Ireland

To Other Countries 15 01 02 No 4.04 plastic packaging R3 M Weighed Abroad


0057-01


an,Ireland

Within the Country 15 01 04 No 1.11 metallic packaging R4 M Weighed Onsite in Ireland

Rilta Environmental Ltd,WCP

MH/2006/32/B WP No.

W0192-03

Block 402,Greenogue

Business Park,Rathcoole,Co.

Dublin,Ireland

Within the Country 15 01 03 No 18.416 wooden packaging R3 M Weighed Onsite in Ireland Quinn Packaging Ltd,.

Rakeelan,.,Ballyconnell,Co.C

avan,Ireland

* Select a row by double-clicking the Description of Waste then click the delete button

Link to previous years waste data

Link to previous years waste summary data & percentage change

Method Used