Presentation Tp

Presentation On: Qlite Lighting Control System

Project: Security Training Facilities Dammam

Client: Ministry of Interior, KSA

Controctor: Al-Khodari

Electrical Sub. Contractor: M.E.C.

Dated: 9 Sep. 2013

Presentation Topics

Lighting control systems are used mainly for efficient and intelligent energy management. This system enables the switching (ON & OFF) of the light fittings via a stand-alone system or a fully networked central system. They can be used in public, commercial or residential properties for areas such as corridors, restrooms, BOH areas, administrative offices, car park, and staircase usually as stand-alone systems or in combination with dimming control system. The system enables the control of light fittings through timers and/or any pre-programmed logic function as specified or needed by the client.Qlite Lighting Control System

System Architecture

System Architecture

Automated Controls of lights based on Occupancy, daylight or time ScheduleIntegration with BMSLocal Preset control from a Key Pad

List of Components Use in STF ProjectFeatures Standard DMX-512 signal. Din rail-mounted. Manual setting available and easy to operate. 8 channels dry contact, each can be set as ON/OFF/ AUTO mode individually. Each channels maximal output can be 10A. Up to 99 zones synchronization. (99 devices work together) Delay time setting (0.1S~10S) for each channel to avoid current surge. Connectable to QL series control panels, each ofthem can work independently or synchronously.

Specification: Power Supply: AC 90240V Output: Maximal output of each channel is 10A Protocol: DMX-512/QL-Net Dimension:215 (W) x 59(H) x 87.5(D)mm Weight: 800gSwitching ModuleQL-SW810

List of Components Use in STF ProjectFeatures DMX-512/QL-NET(RS-485) Din-rail mounted. 8 channels leading-edge (forward phase control) output. Each channel can be set as dimming/switch mode. Up to 99 zones setting. Connectable to QLCP series control panel.

Specification: Power Supply: 90 - 240V AC Protocol: DMX-512, QL-Net Output: 5A per channel, total 12A. Dimension: 215mm(W) x 88mm(H) x 57mm(D) Weight: 720gController ModuleQL-NE100

List of Components Use in STF ProjectSpecification:AC Input: 90 240V DC Output: 12V, 2A Max Dimension: 90(W) x 88 (H) x 57 (D) mm Weight: 310gPower Supply ModuleQL-PS1202

List of Components Use in STF ProjectFeatures In multi-zone mode, one QL-CP106 can control 8 zones. In single zone mode, one QL-CP106 can set up to 255 zones by the DIP switch. Press [1.....6] number key buttons from control panel to directly recall 6 scenes. Press or to raise and lower the dimming level. In curtain control mode,[5&6] number key button can be used for open and close control of the curtains/blinds. 256 level dimming resolutions. Key Lock /unlock function.

Specification: IR receiver. Protocol : QL-NET (RS-485) Connector : 4 pin green terminal Dimension : 86(W) X 86(H) X 34.6(D)mm Weight : 100 gPush Button Control PlateQL-CP106

List of Components Use in STF ProjectPhotocell sensor module sits on the QL NET bus and takes power from the bus.

Photocell Sensor

List of Components Use in STF ProjectFeatures 8 channels. Can connect to 8 dry contacts. Each dry contact has two modes: scene or channel mode. Can set dry contacts working period.(The dry contact works only within this period.) Can set dry contacts delay time. In scene mode, after a scene was call out it will automatically call out another scene or the OFF scene after delay time; in channel mode, after a channel was switch on, it will automatically switch on another channel or switch the channel off after delay time. LCD display and easy operation Portable and user-friendly.Specification: Power supply: DC-12V 200mA (supply by QL-net 4pin green terminal) Protocol:RS-485 Signal input connector :4 PIN green terminal /PHONE JACK Signal output connector:18PIN green terminal Signal output channel8 channels Dimension100(W)*76(H)*35 (D)mm Weight220gQL-S8

List of Components Use in STF ProjectLighting Control & Automation Panels

BMS Control - In each Building eight Zones(areas) for BMS Control will be programmed in Qlite Lighting Control System.

- QL-S8 will provide the interface between Qlite Lighting ControlSystem and BMS.THANK YOU