pre feasibility report - welcome to...

PFR of Ovel Laminate LLP

of 16

PRE FEASIBILITY REPORT

FOR OBTAINING ENVIRONMENTAL CLEARANCE

For the Proposed Resins and

Laminated Sheets Manufacturing Unit of

M/s. Ovel Laminate LLP

Survey No. : 128, Village: Bahadurgadh,

Taluka & District : Morbi, Gujarat - 363642.

Contact No.: 9909595996

Email: [email protected]

Prepared By:

T. R. ASSOCIATES

C-605/A, Ganesh Meridian, Opp. Kargil Petrol Pump,

S. G. Highway, Ahmedabad

Contact No.: 98253 71099

Email: [email protected]

June 2017


of 16

1. Introduction

M/s. Ovel Laminate LLP is a partnership firm proposing to set up a medium scale Resin

and Laminated Sheet Manufacturing unit at Survey No.: 128, Village: Bahadurgadh,

Taluka & District : Morbi - 363642, Gujarat.

2. Project Proponent and their back ground

Company is promoted by its partner. Detail of partners is as given below.

Sr. No. Name of the Partner Background

1 Amitbhai J. Ughreja 9 years experience in Laminated Sheets

Industry

2 Vipulbhai T. Rankja 3 years experience in Laminated Sheets

Industry

3 Naresh S. Aghara 5 years experience in Laminated Sheets

Industry

4 Jasminbhai T. Rankja 4 years experience in Laminated Sheets

Industry

5 Ashish B. Thoriya 6 years experience in Laminated Sheets

Industry

6 Sandip Laljibhai Gambhara 2 years experience in Laminated Sheets

Industry

7 Jayantibhai S. Ughreja 10 years experience in Laminated Sheets

Industry

8 Krupa Chetan Dethariya --

3. Brief description of nature of the project:

M/s. Ovel Laminate LLP is proposing to manufacture Melamine Formaldehyde Resin,

Phenol Formaldehyde Resin & Urea Formaldehyde Resin as well as Laminated Sheets at

Survey No.: 128, Village: Bahadurgadh, Taluka & District : Morbi, Gujarat. Proposed

products will be used for captive consumption as well as for sale purpose.

The proposed final product Laminated Sheets does not attract Environmental Clearance

(EC) from Ministry of Environment, Forest & Climate Change (MoEFCC), New Delhi.

However, the proposed products like Melamine Formaldehyde Resin, Phenol

Formaldehyde Resin and Urea Formaldehyde Resin falls under Category 5(f) as stated in

Environment Impact Assessment Notification Published on 14th September, 2006. Further,

the location of the proposed project is outside the notified industrial estate. Hence, the

project proponent has to obtain the EC from the Ministry of Environment, Forest &


of 16

Climate Change, New Delhi. M/s. T. R. Associates has been appointed to carry out

EIA/EMP studies for obtaining Environmental Clearance.

The total land area of company is 22,966 m2 out of which 8035 m2 (35 % of total land) area

will be used for greenbelt development. The estimated cost of the proposed Resin project

will be 1.25 Crores. Total budget allocation towards Environmental Management Facilities

will be approx. Rs. 40 Lakhs. Total 60 persons will be employed including skilled persons,

unskilled persons and office staff.

Need for the project and its importance to the country and or region:

Resins are used predominantly in the wood based product manufacturing industry as

adhesives. Growth of the resin market is strongly correlated to construction/remodeling

activity (which accounts for over 50% of consumption), and to a lesser degree, to the

automotive industry.

The proposed products like Resins (Melamine Formaldehyde, Urea Formaldehyde and

Phenol Formaldehyde Resins) mainly used to manufacture Laminated Sheets. These

sheets have good market demand to develop the home and office for furniture.

Demand-Supply Gap:

The average production of laminated sheets has crossed approximately 130 million sheets

inclusive of all thicknesses but the gap between installed capacity and demand is growing

bigger. During FY 2011-2012 phases that gap narrowed with sudden demand in lower

thickness segment but later capacities came in place and the laminated sheets market

became a pressure driven market. It is caution for any new comer that if he enters, he

should be prepared for "More investments, more efforts and a long wait for margins".

The burgeoning market demands of urban and semi-urban India are estimated at Rs

5,00,000 Crore. The demand-supply gap has already attracted foreign players to India; and

the e-retailing boom offers immense business opportunities. But a mere 15% of India's

woodworking industry is organized. Its semi-skilled carpenters, self-styled interior

decorators and small-scale local manufacturers will need to be trained and organized to

meet future market demands and exploit business opportunities.

Imports v/s Indigenous production:

Indian market is open and big that is why every kind of import is booming. Indian

plywood and panel trade has become global place as the consumption of different

imported ply panels are on the rise. Unlike before Indians are now welcomed by plywood

manufacturer of China. Earlier India was a self dependent country for commercial or high


of 16

quality plywood, but sharp drop in domestic manufacturing output has resulted in

material sourcing from countries like Burma, Malaysia, Indonesia, China, Vietnam etc.

Now Indian plywood market is somehow curtailed or competed by incoming panel

products from China. Be it film face, decorative, laminate or MR plywood everything is

now being imported partially or more and is sold. Indian industrialist must understand

the fact that its no more a regional shift, it is a global shift. Indian technology should be

upgraded and updated at par with international standards.

The working environment in India has changed tremendously. Earlier the trade fairs were

hardly participated by foreign timber, lumber and plywood manufacturing companies

where as now it is flooded with global suppliers.

Export Possibility:

There is only market of Resins is local market. Resins are intermediate products for

manufacturing of Laminated Sheets. Resins are quite expensive for export. So we have

only local market for sale.

Employment Generation (Direct and Indirect) due to the project:

This project will provide direct employment to 60 persons whereas it will provide

employment to many others indirectly. Plywood and Laminated sheet manufacturing

industries provide employment to large number of people.

4. Project Description

(i) Type of project including interlinked and interdependent projects:

Resins including P.F. resin, M.F. resin & U.F. resin are used in production of

laminated sheets and plywood. So plywood industries, laminated sheets industries

will be interdependent on resin industries.

(ii) Location

Proposed project is to be located at Survey No.: 128, Village: Bahadurgadh, Taluka &,

District: Morbi, Gujarat


of 16

Google image showing proposed project site is given below;

NODE LATTITUDE LONGITUDE

A 23° 2’ 2.70”N 70° 48’ 30.31”N

B 23° 2’ 2.97”N 70° 48’ 27.88”N

C 23° 1’ 52.30”N 70° 48’ 30.42”N

D 23° 1’ 52.76”N 70° 48’ 32.63”N

Salient features in the surroundings area of the proposed site within 10 km radius are as

follows:

Sr. No. Important Features Description

1 Location Survey No.: 128, Village : Bahadurgadh, Taluka &

District: Morbi - 363642, Gujarat.

2 GPS Coordinates Latitude: 23°2'2.70"N

Longitude: 70°48'30.31"E

3 Temperature Range 19.7˚C to 33.8˚C (average)

4 Mean Sea Level 15 m

5 Annual Rain Fall 592 mm (average)

6 Nearest Railway Station Malia Railway Station – 9.38 km in NW

direction

7 Nearest Airport Rajkot Airport – 80.03 km in SSW direction


of 16

Sr. No. Important Features Description

8 Nearest Town Morbi – 24.17 km in S direction

9 Nearest Village Bahadurgadh (Ramrajngar) - 0.8 km in SSW

direction

10 Nearest National Highway NH 27 – 0.17 km in E direction

11 Nearest River/Water body Macchu River – 4.79 km in W direction

12 National Parks / Sanctuary Ghudkhar wild ass sanctuary – 13.58 km in

NNE direction

(iii) Alternative Sites considered

No other sites were selected.

(iv) Size or magnitude of operation

List of Proposed Products

Sr. No. Product Capacity

1. Melamine Formaldehyde Resin 700 MT/Month

2. Phenol Formaldehyde Resin 700 MT/Month

3. Urea Formaldehyde Resin 500 MT/Month

4. Laminated Sheets 3,00,000 Sheets/Month

Note: Resins will be used for captive consumption as well as sell purpose.

(v) Project description with process details

Details of manufacturing process are given in Annexure- 4 of Form- 1.

(vi) Raw material required along with estimated quantity

Sr. No. Name of the Product

Name of the Raw

Materials

Quantity

(MT/Month)

1 Phenol Formaldehyde

Resin

Phenol 322.74

2 Formaldehyde (37 %) 417.79


of 16

3 Caustic 3.68

4 Melamine Formaldehyde

Resin

Melamine 280

5 Formaldehyde (37 %) 416.5

6 Caustic 3.5

7 Urea Formaldehyde Resin Urea 200

8 Formaldehyde (37 %) 295

9 Caustic 2.5

10 Acetic Acid 2.5

(vii) Resource optimization/ recycling and reuse envisaged in the project, if any, should

be briefly outlined.

Latest Process technology will be adopted as available in market with optimum

resources requirement with highest yield and less waste and pollution generation.

Treated industrial effluent will be reused in cooling and other possible activities. In

addition to this, all the feasible cleaner production technologies will be adopted.

(viii) Availability of water its source, Energy/ power requirement and source should be

given.

Energy/power requirement will be 350 kVA which will be procured through Paschim

Gujarat Vij Company Limited.

The total water requirement will be 35 kl/day which will be fulfilled by own Borewell

/ Open well.

(ix) Quantity of wastes to be generated (liquid and solid) and scheme for their

Management/disposal

Hazardous Waste Generation and Disposal

Details of hazardous waste generation and its disposal are given in Annexure- 5 of

Form- 1.

Wastewater Generation and Disposal Facility

Details of domestic as well as industrial wastewater generation and its disposal are

given in Annexure- 7 of Form- 1.


of 16

(x) Schematic representations of the feasibility drawing which give information of

EIA purpose

1. Site Analysis

(i) Connectivity

Nearest railway station Malia 9.38 km

Nearest national highway NH 27 0.17 km

Nearest airport Rajkot 80.03 km

(ii) Land Form, Land use and Land ownership.

Proposed project site has already been procured by proponent and it is an open area

which is presently not being used for any purposes.


of 16

(iii) Existing Land Use Pattern


of 16

(iv) Topography Map


of 16

(v) Existing Infrastructure

(1) Nearest railway station: Malia railway station is 9.38 km away from the project

site

(2) Nearest highway: National Highway 27 is 0.17 km away from the project site.

(3) Nearest airport: Rajkot Airport is 80.03 km from the project site.

(4) Power: 350 kVA from Paschim Gujarat Vij Company Limited.

(5) Water: Source of the water will be a borewell / open well.

(6) Basic amenities: Good road connectivity with state and national highway.

(vi) Soil classification of Morbi District

The soils of Morbi district are of clayey loam to clay type. They are moderately deep to

deep and vary in colour from very dark brown to very dark greyish brown and reddish

brown. The EC of the soils is generally less than 1.0 mmhos/cm and cation exchange

capacity is between 40 and 60 me/100 gm of soil.

(vii) Climate data from secondary source

General climate of the district is sub-tropical and is characterised by three well-defined

seasons, i.e. summer - from April to June, monsoon - from July to September, and winter -

from October to March.

Temperature

Highest temperature is 43 to 46 degree centigrade in summer and lowest temperature

comes down to 7 to 15 degree in winter season.

Humidity

The relative humidity are generally over 75 % in the south west monsoon. In the rest of the

year the air is comparatively dry, especially in the afternoons. During the period of

November to May the relative humidity varies between 40% and 50%.

Wind

In the south west monsoon season, the wind direction is westeraly to south westeraly. In

the post monsoon/cold season, wind blow from the north-north east direction. In summer

seasons the direction of the wind is mainly between north west and south west. The wind

speed gradually increases from February and reaches the peak in July when the south

west monsoon is most active. It again decreases from August and becomes low.


of 16

Rainfall

More than 90% of the rainfall occurs during the monsoon. Rainfall during the winter and

summer months is negligible. The average annual rainfall of the district is 489 mm and in

the year 2016 it is 366 mm only which is around 75 % of the average annual rainfall.

(viii) Social Infrastructure available.

Industrialisation/Entrepreneurship:

On account of availability in huge quantity and suitable climatic condition in the

district has induced the growth of Ceramic industries hugely in Morbi taluka. At

present more than 700 enterprises in around Morbi are Manufacturing Ceramic

Tiles, Floor Tiles, Luster Wall Tiles, Glazed Wall Tiles, Vitrified Tiles, Porcelain

Tiles, 2D, 4 D Tiles, Spartek, Roofing and Mosaic Tiles. More than 100 enterprises

are manufacturing specialized Vitrified Tiles which has great demand in the region

as well as all over the country. It is also hub of digital and other types of watch and

clocks manufacturing enterprises such as Ajanta, Samay, Sonera and Sonam which

are World leaders in this sector. After 2002, Paper industries have grown rapidly as

ancillary sector due to need of high quality craft grade papers very suitable for

packing of goods. There are number of export-import houses working in the

district. Besides, many enterprises deals in consumer durables and engineering

goods. Tourism also fetches significant income to the economy of the district as

many visitors visit the district having historic values. Though the concept of

avoiding risk factor for the Governmental regulations and process causes adverse

effect and resulted in weakened industrial growth. Industrial Training Institutes,

Productivity Development Centers, Small Scale Enterprises Development Institute-

Ahmedabad, District Industries Center- Morbi and other Non Governmental

organizations must come forward to promote more and more training programmes

to increase and motivate the productivity of the labour force available in the

district.

Marketing Potential:

There are well developed Market Yards in Morbi, Wankaner and Halvad taluka of

Morbi district for the distribution of the agricultural produces. Farmers can accrue

more competitive prices for their produce in these market yards by selling their

produces. There is good infrastructure in the district for the sale of industrial goods

and services manufactured and produced.


of 16

2. Planning Brief

(i) Planning Concept (type of industries, facilities transportation etc) Town and

Country Planning/Development authority Classification.

Proposed project site is located near to National Highway 27 and well connected to

the internal roads and highways. The site is well connected to Morbi as well as Rajkot

region, where all the infrastructural and transportation facilities are available.

At present more than 700 enterprises in around Morbi are Manufacturing Ceramic

Tiles, Floor Tiles, Luster Wall Tiles, Glazed Wall Tiles, Vitrified Tiles, Porcelain Tiles,

2D, 4 D Tiles, Spartek, Roofing and Mosaic Tiles. More than 100 enterprises are

manufacturing specialized Vitrified Tiles which has great demand in the region as

well as all over the country. It is also hub of digital and other types of watch and

clocks manufacturing enterprises such as Ajanta, Samay, Sonera and Sonam which are

World leaders in this sector. After 2002, Paper industries have grown rapidly as

ancillary sector due to need of high quality craft grade papers very suitable for

packing of goods

(ii) Population of Morbi District

Description No.

Population Total : 9,60,329 Person

Male : 4,94,726 Person

Female: : 4,65,603 Person

Population density 481 persons per sq. km.

Village Population Total: 6,01,909 Person

Urbanised Population Total: 3,58,420 Person

Population increase rate N.A

Male- Female ratio 1000 : 961

Scheduled Caste population 49,902 persons

Scheduled Tribe population 4,036 persons


of 16

(iii) Land use planning (breakup along with green belt etc).

Sr.

No. Particular Area (m2)

1 Built Up Area 9104

2 Green belt area 8035

3 Open/ Road area 5827

Total 22966

(iv) Assessment of Infrastructure Demand (Physical & Social).

Surrounded villages in 10 km area from the project site are having all the necessary

physical and social infrastructure facilities due to agricultural activities, animal husbandry

and industrial development within the area as well the nearby Morbi Town and

Wankaner Town & Rajkot City.

(v) Amenities/Facilities.

All the basic amenities/facilities such as power connection & power back-up, drinking

water, internal roads, water & wastewater treatment plant etc. will be provided.

3. Proposed Infrastructure

a. Industrial Area

Industry has provided 9104 m2 built up area for industrial process/manufacturing

activity which provides all needed facility including proper ventilation, safe handling

system, etc.

b. Residential Area

Industry will provide labor quarter for their labors and provide all basic facilities to

them.

c. Green Belt.

8035 m2 area will be proposed for greenbelt development. In addition to this, project

proponent will participate in greenbelt development programs in nearby areas under

their CSR.

d. Social Infrastructure

The proponent will provide social infrastructure facilities within 10 km radius of the

proposed project.


of 16

Education Facilities:-Many Facilities for village schools like game kits, drawing kits,

table-chairs; school construction (classroom/toilet/school boundary), ceiling fans/

coolers or books for school library are proposed.

Health Facilities:-Assistance to existing health facilities in nearest Hospital, for

improvement in health facilities or services.

e. Connectivity (Traffic and Transportation Road / Rail / Metro / Water ways

Proposed project site is located adjacent to National Highway 27 and well connected to

the internal roads and highways. The site is well connected to Morbi Town and Rajkot

City.

f. Drinking Water Management

In proposed project, out of 35 kl/day water approx. 5.7 kl/day water will be consumed

for domestic purpose

g. Sewerage System.

Domestic wastewater 5 kl/day will be treated in sewage treatment plant & finally

treated sewage will be used for gardening purpose.

h. Industrial Wastewater Management.

Details of ETP is shown in Annexure – 7 of Form-1.

i. Solid/Hazardous Waste Management

Details of solid / hazardous waste is shown in Annexure – 5 of Form -1.

j. Power Requirement & Supply / source

Power requirement for the proposed project will be approx. 350 kVA which will be

obtained from PGVCL.

4. Rehabilitation and Resettlement (R & R) Plan

Not applicable.


of 16

5. Project Schedule & Cost Estimates

(i) Likely date of start of construction and likely date of completion

(Time schedule for the project to be given)

Construction work is not yet started. Construction work for laminated sheets

manufacturing unit will be started from August 2017 whereas construction work

related to Resin manufacturing plant will be only started after obtaining EC.

(ii) Estimated project cost along with analysis in terms of economic viability of the

project.

Total cost of the Resin project is approx. 1.25 Crore.

------------------------------

pre feasibility report - welcome to...

Documents