platform: dball2 firmware subaru:3 › documents › ...® subaru is a registered trademark and...

Installation Guide

Update Alert: Firmware updates are posted the web on a regular basis. We recommendon

that you check for firmware and/or install guide updates prior to installing this product.

Vehicle Application Guide ....... .................. ..................................... ............................... ......................................................

Key2 & 1 .............. ....... .................. ....GO KEY ................................. .............................. ......................................................

Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )Type 1.............. ..... .................................................................................................................... ..........................................Type 2.............. ..... ................................................................................................................... ..........................................Type 3.............. ..... .................................................................................................................... ..........................................Type 4.............. ..... .................................................................................................................... ..........................................

ProgrammingModule Programming ...................... .............................................................................. .......... ...........................................Module Reset.. ...................................................................................................................................................................Hard ... ....Reset.. ................................................................................................................................................................Feature & Option List..........................................................................................................................................................Feature Programming.........................................................................................................................................................

LED Diagnostics & Troubleshooting...................................................................................................................................

Limited One-Year Consumer ........Warranty.......................................................................................................................

Quick Reference Guide......................................................................................................................................................

02

03

04070911

1315151617

18

20

21

Index

® Subaru is a registered trademark and property of its company.

K is required.ey2GO

The 3 firmware for 2 is an all-in-one door lock and override module compatible withSUBARU DBALLspecific Subaru vehicles.

This module can only be flashed and configured using Xpress at www.directechs.com orVIPusing the Directechs Mobile application for smartphones. Refer to the Module Programmingsection 1on page 3 for more information.

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3

© 201 Directed.7 All rights reserved.

Vehicle Application Guide

The table below lists the vehicles and features which are compatible with this product. Refer to the following pages formore information on installation wiring, programming and troubleshooting for these vehicles.

Vehicles

2017

2016

2015

2014

2013

PK

-Im

mobilizer

Bypass-D

ata

No

Key

Req'd

CC

-Heate

dM

irro

rs

CC

-Rear

Win

dow

Defo

gger

Activ

atio

n

DL-A

rmF

acto

ryS

ecurity

DL-D

isarm

Facto

ryS

ecurity

DL-D

oor

Lock

Contr

ol

DL-D

oor

Unlo

ck

DL-D

river

Priority

Unlo

ck

DL-T

runk

/H

atc

hR

ele

ase

Key2G

O

RS

-RA

PS

hutD

ow

n(R

eta

ined

AC

CP

ow

er)

RS

-Rem

ote

Sta

rtR

eady

RS

-Sm

art

Sta

rt

RS

-Tach

/R

PM

Outp

ut

SS

-Entr

yM

onito

ring

ALL

Door

Pin

s

SS

-Entr

yM

onito

ring

Tru

nk/H

atc

hP

in

ST

-Bra

ke

Sta

tus

(footbra

ke)

ST

-E-B

rake

Sta

tus

ST

-Igniti

on

Sta

tus

Subaru

Crosstrek (Smart Key) 2 2 • • • • • • • • • D D • • • • • •

Forester (Smart Key) 1 1 1 1 • • • • • • • • • D D • • • • • •

Impreza (Smart Key) 2 2 • • • • • • • • • • • D D • • • • • •

Legacy (Smart Key) 3 3 3 4 4 • • • • • • • • • • • D D • • • • • •

Outback (Smart Key) 3 3 3 4 4 • • • • • • • • • • • D D • • • • • •

WRX (Smart Key) 1 1 1 • • • • • • • • • D D • • • • • •

XV Crosstrek (Smart Key) 2 2 • • • • • • • • • D D • • • • • •

Legend:

D: Data-to-Data (D2D) only

•: D2D and Wire-to-Wire (W2W)

PK: Transponder & Immobilizer Override

CC: Comfort & Convenience Controls

DL: OE Door Lock & Alarm Controls

RS: Remote Start & Engine Controls

ST: Function/Feature Status

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


This feature is mandatory to control the immobilizer override in this firmware.

Key2 has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It usesGOan array of servers to generate a duplicate of the original key, the installation of a remote starter without having toallowinggive up a key.

The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.

All Key2 -compatible firmware are clearly indicated in the function list of each vehicle search result page and will alsoGOappear on the flash page. Any first-time user must re-register to gain access to Key2 , and some additional informationGOwill be required to complete the registration process, such as your Directed account number and store name.

Key2 is compatible with Xpress 4.5 or higher and requires an oader.GO VIP XKL

Refer to page 1 of this guide for instructions on how to program features using Key2 .4 GO

15

2

3

4

98

7

6

16

1718

19

20

2122

23

2425

26

2728

15

14

13

12

11

10

8

16

1

9

Installation Type 1

Not required in D2D mode.

[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the diagnostic connector.OBDII

(+) Brake Status Input

(-) Lock Output

(-) Hatch/PowerLiftgate Release Output

(-) Unlock Output

[1] ( ) Tach InputAC

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

Rem

ote

Sta

rter

(-) (Status)GWR

(-) OutputTrunk

(+) Ignition 1 Output

(+) Starter Output

(-) Ground

10

2DBALL

RF

Prog utton. B

LED

1: (-) Lock InputGreen:

2: (-) Unlock InputBlue:

3: (-) Trunk InputRed/White:

10: (-) (Status) InputBlue/White: GWR

4

14

12

2

[1] ( ) Tach OutputAC : 5Violet/White:

Immo. Data 1: 1Orange/Black:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

TX

(-) Ground

RX

(+)12V

XKD2D65

(-) Status OutputE-Brake : 1Black/White:

(+) 12V (+) 12V: 13Red:

(-) Ground (-) Ground: 14Black:

(+) Brake Status 6: Gray:

(-) Push-to-Start Output: 9Violet/Brown:

(+) OutputAccessory


9 + Ignition: ( ) InputPink:

HS High pin 6CAN : Red,

HS C Low: pin 14AN Blue,

OB IIDDiagnosticconnector

(+) Acc : pinessory 4Blue or Violet,

123

789

192021

456

161718

282930

101112131415

222324252627

Keyless AccessModule(White conn. (C)right of BCM)

Junction conn.(White conn. driver’s

kick panel)

(+) Ignition :1Violet,

6pin

( )- :PTS Black orGreen, pin 30

( )- Parking Lights

Refer to the Vehicle Wiring Reference Chart on page for wire color and location.s next

Immo Data Interr. 10(veh. side): Orange/Red:

I (conn. side):mmo Data Interr. 11Yellow/Red:

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

(-) Parking Light:Lt.Green or Black/Blue, pin 18

Headlight Switch(White conn. at )parking light switch

Cut

8 410 6 27 39 5 1

18 1420 16 1217 1319 15 11

(-) OutputLock

(-) OutputUnlock

Refer to the VehicleWiring ReferenceChart on pages nextfor wire colors andlocation.

HS CAN 2 High: 5Orange/Green:

HS CAN 2 Low: 6Orange/Brown:

HS CAN Low2 :Blue or RedLt. , 15pin

HS CAN High2 :White, 14pin

(+) 12V

12

3789 456

161718

10

1112131415

Keyless Access Module(White conn. (A) )right of BCM

(+) Starter: Pink,or Brown 7pin

(+) : inIgnition 2 P 9

(-) Unlock:Blue/Black,

6pin 1

(-) Lock:Lt. Blue,pin 15

4 3 2 156789

( ) : pin 2+ 12V Red,

Driver’s Fuse Box(Brown conn. back

of dash fuse box)

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Type 1 - Vehicle Wiring Reference Charts

Forester XT (Smart Key) andWRX (Smart Key) ECM Connector

2525

1313

3737

11

1414

3838

22

2626

1515

3939

33

2727

1616

4040

44

2828

1717

4141

55

2929

1818

4242

66

3030

1919

4343

77

3131

2020

4444

88

3232

2121

4545

99

3333

2222

4646

1010

3434

2424

4848

1212

3636

2323

4747

1111

3535

Immo. DataImmo. Data

Forester 2.5i (Smart Key) andWRX STi (Smart Key) ECM Connector

2129

7 6 5 4 3 2 11718

2634

192735

16152533

2331

142432

2230

132028

121110 9 8

ECM behind glove boxwhite 35 pin plug (B)

ECM on passenger fenderor ECM next to air cleanerassembly, black 48 pin plug

Function Color Pin Polarity Location Color Pins

Power Liftgate Brown/White 1 (+) Power liftgate switch White 6

12V Red 2 (+) Back of dash fuse box. Brown 9

HS CAN 1 High Red 6 Data OBDII. White 16

HS CAN 1 Low Blue 14 Data OBDII. White 16

Starter Brown 7 (+) Connector A - Keyless Access Module right of BCM. White 18

Ignition 2 Tan or White 9 (+) Connector A - Keyless Access Module right of BCM. White 18

Parking Lights Lt. Green 18 (-) Headlight switch. White 20

Lock Lt. Blue 15 (-) Junction connector drivers kick panel. White 28

Unlock Blue/Black 16 (-) Junction connector drivers kick panel. White 28

PTS Green 30 (-) Connector C - Keyless Access Module right of BCM. White 30

Ignition 1 Violet 6 (+) Connector C - Keyless Access Module right of BCM. White 30

Accessory Violet 4 (+) Connector C - Keyless Access Module right of BCM. White 30

HS CAN 2 High White 14 Data Connector C - Keyless Access Module right of BCM. White 30

HS CAN 2 Low Red 15 Data Connector C - Keyless Access Module right of BCM. White 30

Hatch Release Blue 10 (-) BCM under drivers dash. White 35

Immo. Data Green/Black 43 Data ECM on passenger fender. Black 48

Power Liftgate Brown/White 1 (+) Power liftgate switch White 6




Starter Brown 7 (+) Connector A - Keyless Access Module right of BCM. White 18

Ignition 2 Tan or White 9 (+) Connector A - Keyless Access Module right of BCM. White 18

Parking Lights Lt. Green 18 (-) Headlight switch. White 20

Lock Lt. Blue 15 (-) Junction connector drivers kick panel. White 28


PTS Green 30 (-) Connector C - Keyless Access Module right of BCM. White 30


Accessory Violet 4 (+) Connector C - Keyless Access Module right of BCM. White 30



Immo. Data White/Blue 25 Data ECM behind glove box. White 35

Hatch Release Blue 10 (-) BCM under drivers dash. White 35

Wire Information Connector Information

Subaru Forester 2.5i (Smart Key) 2014-2016

Subaru Forester XT (Smart Key) 2014-2016

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Type 1 - Vehicle Wiring Reference Charts

Keyless Access Module

A B C

1

18

1

17

4

28

6

30

12

11

345678910

12141615 1317 2726 252423 222120

161514 131211 10 9 8 7 6 5

1819

3 2

192120

79 8101211

222423

131514

252726

161817

45 23

2829


Trunk Release Green/Red 2 (-) Trunk release switch. Gray 4




Starter Pink 7 (+) Connector A - Keyless Access Module right of BCM. White 18

Ignition 2 Lt. Blue 9 (+) Connector A - Keyless Access Module right of BCM. White 18

Parking Lights Black/Blue 18 (-) Headlight switch. White 20

Lock Lt. Green/Black 15 (-) Junction connector drivers kick panel. White 28


PTS Black 30 (-) Connector C - Keyless Access Module right of BCM. White 30


Accessory Blue 4 (+) Connector C - Keyless Access Module right of BCM. White 30


HS CAN 2 Low Lt. Blue 15 Data Connector C - Keyless Access Module right of BCM. White 30

Immo. Data Green/Black 43 Data ECM next to air cleaner assembly. Black 48

Trunk Release Green/Red 2 (-) Trunk release switch. Gray 4














Immo. Data Red/White 25 Data ECM behind glove box. White 35


Subaru WRX (Smart Key) 2015-2017

Subaru WRX STi (Smart Key) 2015-2017

Installation Type 2


Refer to the Vehicle Wiring Reference Chart on the next page for wire color and location.s




(-) Door Status Input(-) E-Brake Status Input

Rem

ote

Sta

rter

(-) (Status)GWR

(-) OutputTrunk

(+) Ignition 1 Output(+) Starter Output

10

2DBALL

RF

Prog utton. B

LED





4

14

12

2





TX

(-) Ground

RX

(+)12V

XKD2D65


(+) 12V (+) 12V: 13Red:



Immo Data Interr. 11(conn. side): Yellow/Red:



(+) OutputAccessory (+) Ignition 2 Output


(+) : pinIgnition 2 9Lt.Blue,

Immo.Data:Red/Yellow or Yellow, pin 25

(+) Starter:Pink, 7pin

ECM(White conn. )behind glove box

12

3789 456

161718

10

1112131415

(-) OutputLock

(-) OutputUnlock



4 3 2 112 11

2331

142432

102230

13 92129

87 6 5

17182634

192735

16152533

2028

8

16

1

9

HS HighCAN :Red, pin 6

HS C Low:ANBlue, pin 14

OB IIDDiagnosticconnector


HS CAN Low: 4Tan:



( )- Parking Lights

(-) Parking Light:Black/Blue, pin 18

Headlight Switch(White conn. at parking

light )switch

8 410 6 27 39 5 1

18 1420 16 1217 1319 15 11

HS CAN Low:2Blue,

15pin

(+) Acc : pinessory 4Blue,

(+) Ignition pin1: 6Violet,

( ) :- PTSBlack,

30pin

HS CAN High:2White,

14pin

123

789

192021

456

161718

282930

101112131415

222324252627

(+) 12V

(-) Ground

(-) Lock Output


(-) Unlock Output

Cut

15

2

3

4

98

7

6

16

1718

19

20

2122

23

2425

26

2728

15

14

13

12

11

10

Junction conn.(White conn. driver’s

kick panel)

(-) Unlock:Blue/Black,

6pin 1

(-) Lock:Lt. Blue,pin 15

Keyless Access Module(White conn. (A) )right of BCM

Keyless AccessModule (White conn.(C) )right of BCM

Refer to the VehicleWiring ReferenceChart on page fors nextwire colors and location.

4 3 2 156789

Driver’s Fuse Box(Brown conn. back

of dash fuse box)

( ) : pin 2+ 12V Red,

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Type - Vehicle2 Wiring Reference Charts


A B C

1

18

1

17

4

28

6

30

12

11

345678910

12141615 1317 2726 252423 222120

161514 131211 10 9 8 7 6 5

1819

3 2

192120

79 8101211

222423

131514

252726

161817

45 23

2829


12V Red 6 (+) Back of fuse box. Brown 9








PTS Black 30 (-) Keyless Access Module right of BCM. White 30

Ignition 1 Violet 6 (+) Keyless Access Module right of BCM. White 30

Accessory Blue 4 (+) Keyless Access Module right of BCM. White 30

HS CAN 2 High White 14 Data Keyless Access Module right of BCM. White 30

HS CAN 2 Low Blue 15 Data Keyless Access Module right of BCM. White 30

Trunk Release (4 door) Black/Blue 7 5-wire BCM under drivers dash. White 31

Immo. Data Red/Yellow or Yellow 25 Data ECM behind glove box. White 35

Trunk Release (5 door) Green/Red 10 (-) BCM under drivers dash. White 35







Lock Lt. Gree/Black 15 (-) Junction connector drivers kick panel. White 28






HS CAN 2 Low Blue 15 Data Connector C - Keyless Access Module right of BCM. White 30


Trunk Release Yellow/Blue 10 (-) BCM under drivers dash. White 35







Lock Lt. Gree/Black 15 (-) Junction connector drivers kick panel. White 28








Trunk Release Yellow/Blue 10 (-) BCM under drivers dash. White 35

Subaru Impreza (Smart Key) 2015-2016

Subaru XV Crosstrek/Crosstrek Hybrid (Smart Key) 2014-2016

Subaru XV Crosstrek/Crosstrek (Smart Key) 2014-2015


20 1216 8 418 1014 6 219 1115 7 317 913 5 1

40 3236 28 2438 3034 26 2239 3135 27 2337 2933 25 21

Installation Type 3










Rem

ote

Sta

rter

(-) (Status)GWR

(-) OutputLock

(-) OutputUnlock

(-) OutputTrunk


(+) Starter Output

10

2DBALL

RF

Prog utton. B

LED





4

14

12

2





TX

(-) Ground

RX

(+)12V

XKD2D65


(+) 12V (+) 12V: 13Red:






(+) Accessory Output

(+) Acc : pinessory 23Green,

(+) Ignition : pin1 12Gray/Red,

( ) : pin- 4PTS Red,


Immo.Data :pin 38Red/White:

HS High:CAN 2,Red pin 10

HS C Low:AN 2Blue, pin 11

(-) Lock: pin, 32Brown/White

(+) Starter:pinWhite/Green, 35

(-) Unlock:Brown/Black,pin 12

(-) TrunkRelease:Blue/Green,pin 6

(-) Hatch/Power Liftgate Release:Blue/Green, pin 1

(-) Parking Light: pin 1Black, 8

( )- Parking Lights

Headlight Switch(White conn. at parking light switch)

Keyless Access Module(White conn. (A)

)behind cluster12 8 410 6 211 7 39 5 1

24 20 1622 18 1423 19 1521 17 13

(+) Ignition 2 Output(+) Ignition : pin2 11Lt.Blue/Red,

Keyless Access Module(White conn. (B)

)behind cluster

ECM connector(white bottom connectorpassenger side under hood)

12345678910

11121314151617181920


HS CAN Low: 4Tan:



8

16

1

9

HS High:CANRed, pin 6

HS C Low:ANBlue, pin 14

OB IID Diagnostic connector

12

4 3 2 1

34

Driver’s Fuse Box(White conn. rearof dash fuse box)

Hatch/PowerLiftgate Release Switch

(gray conn. at release switch)

( ) :+ 12VRed, pin 3

(+) 12V

(-) Ground

(-) Lock Output


(-) Unlock Output

OR

Cut

121110 9 8 7 6 5 4 3 2 113263952

65 53404142434445464748495051

5455565758596061626364

27141516171819202122232425

28303132333435363738 29

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Type - Vehicle3 Wiring Reference Charts


Trunk Release Blue/Green 1 (-) Trunk release switch. Gray 4

12V Red 3 (+) Rear of dash fuse box. White 4



Parking Lights Black 18 (-) Headlight switch. White 20

PTS Red 4 (-) Connector A - Keyless Access Module right of BCM. White 24

Ignition 1 Gray/Red 12 (+) Connector A - Keyless Access Module right of BCM. White 24


Accessory Green 23 (+) Connector A - Keyless Access Module right of BCM. White 24

Hatch Release Blue/Green 6 (-) Rear of dash fuse box. White 40

Starter White/Green 35 (+) Connector C - Keyless Access Module right of BCM. White 40

HS CAN 2 High Red 10 Data Connector C - Keyless Access Module right of BCM. White 40


Lock Brown/White 32 (-) Rear of dash fuse box. White 40

Unlock Brown/Black 12 (-) Rear of dash fuse box. White 40

Immo. Data Red/White 38 Data ECM passenger side underhood, bottom connector. White 65

Power Liftgate Blue/Green 1 (-) Power liftgate switch. Gray 4

12V Red 3 (+) Rear of dash fuse box. White 4



Parking Lights Black 18 (-) Headlight switch. White 20

PTS Red 4 (-) Connector A - Keyless Access Module right of BCM. White 24

Ignition 1 Gray/Red 12 (+) Connector A - Keyless Access Module right of BCM. White 24

Ignition 2 Lt. Blue/Red 11 (+) Connector A - Keyless Access Module right of BCM. White 24

Accessory Green 23 (+) Connector A - Keyless Access Module right of BCM. White 24

Starter White/Green 35 (+) Connector C - Keyless Access Module right of BCM. White 40



Lock Brown/White 32 (-) Rear of dash fuse box. White 40

Unlock Brown/Black 12 (-) Rear of dash fuse box. White 40

Hatch Release Blue/Green 6 (-) Rear of dash fuse box. White 40

Immo. Data Red/White 38 Data ECM passenger side underhood, bottom connector. White 65


Subaru Legacy (Smart Key) 2015-2016

Subaru Outback (Smart Key) 2015-2016


12 8 410 6 211 7 39 5 1

24 20 1622 18 1423 19 1521 17 13

20 1216 8 418 1014 6 219 1115 7 317 913 5 1

40 3236 28 2438 3034 26 2239 3135 27 2337 2933 25 21(A) (B)

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Installation Type 4










Rem

ote

Sta

rter

(-) (Status)GWR

(-) OutputLock

(-) OutputUnlock

(-) OutputTrunk


(+) Starter Output

10

2DBALL

RF

Prog utton. B

LED





4

14

12

2


Immo. Data (Veh. side) 1: 1Orange/Black:



TX

(-) Ground

RX

(+)12V

XKD2D65


(+) 12V (+) 12V: 13Red:






(+) Ignition 2 Output(+) Acc : pinessory 4Red,(+) Ignition :1Yellow, pin 6

(-) Trunk/Hatch Release:Red, pin 10

(-) Lock: , pin 9Brown/White

(-) Unlock: , pin 20Brown/Black

35343332 31 3029281718192021222324252627

1615 141312 11 10 9 8 7123456

( ) :- PTSWhite,

28pin


Immo.Data :pin 2Red/White: 5

HS C Low:AN 2White, pin 15

(+) Starter: pin, 7Pink

( )- Parking LightsKeyless AccessModule(White conn.(C) behindfuse box)

(+) OutputAccessory

(+) Ignition 2:Violet, pin 9


HS CAN Low: 4Tan:



Relay Holder(White conn. behind dash fuse box.)

(+) 12V

ECM(White conn.

)behind glovebox

(+) : pin12V , 36White

Body Integrated Unit(White conn. right ofsteering column.)

Body Integrated Unit(White conn. right of steering column.)

(-) Parking Light:Black/White, pin 17 HS CAN 1 High: pin 20Red,

HS CAN 1 Low 28: pinBlue,

HS C HighAN 2Red, pin 14

Keyless Access Module(White conn. (A) behind fuse box.)

(-) Ground

(-) Lock Output

(-) Hatch/Power Liftgate Release Output

(-) Unlock Output

Cut

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Type -4 Vehicle Wiring Reference ChartsPage 21



Ignition 2 Violet 9 (+) Connector A - Keyless Access Module right of BCM. White 18

PTS White 28 (-) Connector C - Keyless Access Module right of BCM. White 30

Ignition 1 Yellow 6 (+) Connector C - Keyless Access Module right of BCM. White 30

Accessory Red 4 (+) Connector C - Keyless Access Module right of BCM. White 30


HS CAN 2 Low White 15 Data Connector C - Keyless Access Module right of BCM. White 30

Lock Brown/White 9 (-) BCM right of steering column White 35

Unlock Brown/Black 20 (-) BCM right of steering column White 35

Trunk Release Red 10 (-) BCM right of steering column White 35

HS CAN 1 High Red 20 Data BCM right of steering column White 35

HS CAN 1 Low Blue 28 Data BCM right of steering column White 35

Parking Lights Black/White 17 (-) BCM right of steering column White 35

Immo. Data Red/White 25 Data ECM behind glovebox. White 35

12V White 36 (+) Relay holder behind dash fuse box. White 44


Ignition 2 Violet 9 (+) Connector A - Keyless Access Module right of BCM. White 18

PTS White 28 (-) Connector C - Keyless Access Module right of BCM. White 30

Ignition 1 Yellow 6 (+) Connector C - Keyless Access Module right of BCM. White 30

Accessory Red 4 (+) Connector C - Keyless Access Module right of BCM. White 30


HS CAN 2 Low White 15 Data Connector C - Keyless Access Module right of BCM. White 30

Lock Brown/White 9 (-) BCM right of steering column White 35

Unlock Brown/Black 20 (-) BCM right of steering column White 35

Hatch Release Red 10 (-) BCM right of steering column White 35

HS CAN 1 High Red 20 Data BCM right of steering column White 35

HS CAN 1 Low Blue 28 Data BCM right of steering column White 35

Parking Lights Black/White 17 (-) BCM right of steering column White 35

Immo. Data Red/White 25 Data ECM behind glovebox. White 35

12V White 36 (+) Relay holder behind dash fuse box. White 44

Subaru Outback (Smart Key) 2013-2014

Subaru Legacy (Smart Key) 2013-2014

Connector InformationWire Information


A B C

1

18

1

17

4

28

6

30

12

11

345678910

12141615 1317 2726 252423 222120

161514 131211 10 9 8 7 6 5

1819

3 2

192120

79 8101211

222423

131514

252726

161817

45 23

2829

Module ProgrammingPage 31

1Solid

Wait until the LED turns solid red.ON

Note: To skip the transponder programming and use convenience features only, pressthe 5 times. The will turn orange then proceed to step 2.programming button LED

3

Press presson the brake and then the (Push-to-Start)PTSbutton in order to start the vehicle. The flashesLED greenquickly.

If the transponder programming was skipped, the LEDturns solid orange for 3 seconds then shuts whenON OFFprogramming is done.

2

Solid Orangex3 secs

Off

&

ENGINESTARTSTOP

PUSH

Important

Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.

Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP

When the flashing operation is successful, you can proceed with the programming instructions below.

Refer to the Diagnostics section on page -19 for more information and for troubleshooting purposes.LED s 18

OR

If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses tothe module, then connect the 4-pin D2D harness.

D2D Installation

W W Installation2

If required for your installation, connect the 10-pin and 12-pin harnesses to themodule, then connect the 14-pin harness to the module.

10-pinD2D

1st

12-pin14-pin

2nd

3rd

10-pinD2D

1st

4th

12-pin14-pin

2nd

3rd

Flashing a module using your computer:

1. Connect the interface module to your computer using theXKLoader2.

2. Go to www.directechs.com using Internet Explorer, andselect the button.Flash Module

3. Follow the instructions to select your vehicle, installationtype, and configure your options.

4. Once you have configured the firmware options, click on theFLASH button.

Flashing a module using your smartphone or tablet

1. Connect the interface module to your oader3.XKL

2. Launch the Directechs Mobile app on your smartphone ortablet.

3. Select and follow the on screenFLASH YOUR MODULEinstructions.

Go to the next page t complete the module programming.o

Wait for t to flash orange indicating the Key2Go sequence was initiated.he LED

Flashes Orange

Press the

brake pedal & &Flashes green

quickly

4 Disconnect the module and complete the programming.Key2GO

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Page 41

You have successfully completed the programming sequence.module

3

2

1

Once the configuration is completed, reconnect the module.The LED ON solid .turns green for 3 seconds, then turns off

Click on .Submit Key2G RequestO

Remove the from the vehicle and reconnect it to your computer. The web site will automaticallymodulerecognize that you are moving onto the second phase of the programming sequence.

Refer to the LED Diagnostics section on page n for more information and for troubleshooting purposes.Version 4.5 or higher of XpressVIP must be installed on your computer to complete this programming sequence.

Web Programming (for Key2GO)

Solid x3 Secs

&Off

2

Solid

&

Solid Flashes

&

Release

3

Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsONuntil the andLED starts to flash orange red.

Release the programming button. The turns solid red.LED ON

Warning gainst xecuting a Hard Reset!A EA hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (suchas and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List

1 OR

If required for your installation, c , &onnect the 10-pin 12-pin14-pin harnesses to the module Press hold the. andp , then connect the 4-pin D2D harness.rogramming button

D2D Installation

If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

1st

12-pin14-pin

2nd

4th

3rd

10-pinD2D

1st

5th

12-pin14-pin

2nd

3rd

4th

Module Reset

Hard Reset

2 & &Solid SolidRelease

Wait 3 seconds until the orange then release theLED turns solidONp The then turns solid red.rogramming button. LED ON

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashedto the module using the web config tool will not be affected.

Page 51

1 OR

If required for your installation, c , &onnect the 10-pin 12-pin14-pin harnesses to the module Press hold the. andp , then connect the 4-pin D2D harness.rogramming button

D2D Installation

If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

1st

12-pin14-pin

2nd

4th

3rd

10-pinD2D

1st

5th

12-pin14-pin

2nd

3rd

4th

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Feature & Option List

It is recommended to configure all features and options listed below thethe using configuration tool found on the moduleflashing page on www.directechs.com. The web offers more options; however, manual configuration of the features ispossible using the information on this page.

* Default Option

Feat. Operation Flashes/Options Description

1. No RF Output* Module is connected to a remote starter using a standard installation.

2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).

3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).

1. Driver priority*Unlocks only the driver door when the button is first pressed, and unlocks all doors when it is

pressed a second time within 5 seconds.

2. All Unlocks all doors when the button is first pressed.

1. Disabled* No operation.

2. Enabled When the feature is enabled, it will activate the rear defroster and heated mirrors.

1. 32 °F (0 °C)*When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start

when temperature is below 32 °F (0 °C).

2. 23 °F (-5 °C)When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start

when temperature is below 23 °F (-5 °C).

3. 41 °F (5 °C)When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start

when temperature is below 41 °F (5 °C).

4. Always ON When Heated Seats or Defroster feature is enabled, it will activate the feature at any temperature.

1. Disabled

The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command

will be executed at the beginning or end of the sequence; it must be controlled by the Remote

Starter.

2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will

unlock at the beginning of the sequence, and relock after start and shutdown.

3. Enabled*

Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm

the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm

control must often be done by lock or unlock operation. This could create unnecessary actions

on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will

monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle

is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart

OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is

not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with

this option and will make it invisible to the user.

RFTD Output

Type1

5Smart OEM

Alarm Control

Unlock Driver

Priority2

Defroster3

4

Heated

Seats/Defroster

Temperature

Control

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


To enter feature programming routine� Turn t , thenhe ignition .ON OFF� Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( )

Programming button.� The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red

the current option of feature 1 .(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence willrepeat until .a new command is entered

Changing feature options� Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.� The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDred

the number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered

Accessing another feature� Press and release the programming button a number of times to advance from the current feature to the next desired feature.� The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED

indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered

When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED

Once a feature is programmed� Other features can be programmed.� The feature programming can be exited.

Exiting feature programming� No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON

sequence.OR

� Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ONend of the programming sequence.

Feature ProgrammingProgramming

Button

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


Page 81

LED Diagnostics & Troubleshooting

LED Description Troubleshooting

Module has no power.

Make sure the D2D harness is connected or that the 12

Volt is present between the red and black wires. If the

12 Volt is present, the module may be defective.

Waiting to begin the programming sequence.Ensure the correct programming procedure is being

followed.

Initialization failed.Reset the module and complete the programming again.

If the issue persists, please contact Technical Support.

Transponder functions were skipped.

(If compatible) when RXT mode is not desired or

convenience features are needed, please reset and

reprogram the module.

All required CAN networks has been detected. Normal operation.

1 of 2 CAN networks has been detected. Normal operation

Key2GO initiated.Please follow the steps indicated in “Module

programming” to complete the Key2GO programming.

Module was successfully programmed with all functions. Normal operation

Module was successfully programmed without

transponder functions.Normal operation.

CAN2 not detected.

Check the CAN2 Orange/Green and Orange/Brown wire

connections. Wake up the data bus by turning the

ignition on and try again. If your installation does not

require this connection, skip this step by pressing the

programming button 5 times.

J1850 not detected.Check the J1850 wire connection. Wake up the data bus

by turning the ignition on and try again.

CAN1 not detected.

Check the CAN1 Tan and Tan/Black wire connections.

Wake up the data bus by turning the ignition on and try

again. If your installation does not require this

connection, skip this step by pressing the programming

button 5 times.

Bypass data not detected.

Check the bypass line connection. If more than one wire

is used, make sure they are not inverted. Ensure the

vehicle still operates correctly using the factory key.

Bypass processing error.

The bypass calculation failed. Reset the module and try

again. If the condition persists, please contact Technical

Support.

ISO 1 not detected.

The Yellow/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

ISO 2 not detected.

The Orange/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

MUX not detected.

The Violet/Green or Violet/Brown wire did not detect the

expected voltage value. Refer to "Installation (wiring

diagrams & vehicle wiring reference charts)" to check

the connections.

Module Programming

Module Programming - Error Codes

Solid red

Flashes redx 1

Flashes redx 1

Flashes redx 2

Flashes redx 3

Flashes redx 4

Flashes redx 5

Flashes redx 6

Flashes redx 7

Solid greenx 3 secs

Flashesgreen

Solid orange

Flashes red& green

Off

Flashesorange

Flashesorangeslowly

Solid orangex 3 secs

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


LED Description Troubleshooting

OBDII feature is not supported.The diagnostic data bus was not detected, therefore the

SmartStart features will be limited.

Ground When Running (Status) command received. The module has initialized the remote start sequence.

Ignition ON command received.The module has received the Ignition ON command and

is processing the remote start sequence.

Start ON command received.The module has received the Start ON command and is

processing the remote start sequence.

PTS shutdown error.The PTS output from the module was not activated due

to safety protection.

CAN bus incorrectly detected.

Verify the CAN1 and CAN2 connections. Refer to

“Installation (wiring diagrams & vehicle wiring reference

charts)” to check the connections.

LOCK command received.

UNLOCK command received.

TRUNK command received.

AUX1 command received.



Takeover successful. Normal operation.

Runsafe was not disabled.No UNLOCK command was received prior to opening the

door, or the 45 second timer expired in takeover mode.

Brake was not detected.The brakes were not detected, which prevents the

system from shutting down the vehicle.

Smart key was not detected.The smart key was not detected, which prevents the

system from shutting down the vehicle.

Speed was detected.The vehicle was detected as moving, which prevents the

system from shutting it down.

External module synchronization

Commands

Activation Ground When Running (Status)

If the bypass module fails to flash, it did not receive the

signal. Commands can come from RF or D2D.

Shutdown codes

(Flashes red,red thenorange) x 10

Flashes red& orange

Flashes redx 21

Flashes redx 2

Flashes redx 4

Flashes redx 10

Flashes redx 1

Flashes redx 3

Flashesgreen

Flashesgreenquickly

Flashesgreen x 1

Flashesorange x 1

Flashesorange x 2

Flashesorange x 3

Flashesorange x 5

Flashesorange x 4

Flashesorange x 6

For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEARElectronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, theDIRECTEDsecurity or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or materialunder normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTEDand the Part is returned to , postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing theDIRECTEDfollowing information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and completeproduct and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to itsintended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation orother causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING, , ,BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY, , ,FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUALPROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY, ;PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS,PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALLACTS OF.THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR. AINSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS, , , ,AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION, ,LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING, , . A ADIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF,CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE.DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED.TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S .RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL, ,DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL, , , ,LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE, . ,MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THEA ’SPARTAS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States ofAmerica and Canada. Parts sold outside of the United States ofAmerica or Canada are sold “ - ” and shall have , express or implied. Some states do not allow limitationsAS IS NO WARRANTYon how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warrantygives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTEDnot authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTEDwebsite at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the selectvehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. : Under noDISCLAIMERcircumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for anyconsequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, norwill they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / databus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of thisproduct be liable for consequential damages sustained in connection with this product and neither assumes nor authorizesany representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; EuropeanPatent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

Limited Consumer WarrantyOne Year

Rev.: 20 706271

Platform: DBALL2

Firmware SUBARU: 3


1

2

3

Stop the vehicle in a safe parking spot and put the gear in Park (P).

Press remote start

button*

* Your aftermarket remote may differ from the model shown in the illustrations.

Stop & put vehicle in Park (P)

P&

Quick Reference GuideDBALL2-SUBARU3

© 2017 Directed. All rights reserved.

Pit Stop Mode

The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.

Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.

It is now safe to leave the engine running and exit the vehicle with the factory remote in hand.

Press the button to remote start the vehicle.*

The parking lights will flash once

to indicate the vehicle is now in

Pit Stop Mode.

Exit vehicle with Smart Key

Vehicle Takeover with Get In and Go*

4

3

1Close the vehicle doors, hood and trunk, then press the Remote Start button on the transmitter to start the vehicle.**

2

Depress the brake pedal, put the car in gear and drive off.

Enter the vehicle, while making sure the factory remote is inside with you.

Send the unlock command onthe factory or aftermarket remote.**

Ready to drive off

Press remote start

button**

Press Unlock button on

either remote**OR

** Your aftermarket remote may differ from the model shown in the illustrations.

Enter vehicle with key fob

GG

* Get In and Go connections required.

Get In and Go

Get In and Go is designed to provide users with easy takeover when entering their Push-to-Start (PTS) equipped vehicle, once it has been remote started.

Typically, users would have to remote start their vehicle, then get inside and press the vehicle start button to perform a takeover. There is therefore a physical action required to drive away. With Get In and Go technology, you simply remote start the vehicle, unlock the doors, get in and go... Nothing to do but put the gear in drive and enjoy your vehicle.

This unique feature monitors a variety of parameters such as the key fob, vehicle speed sensor and door sensor, in order to perform takeover securily.

GG

Complete the following steps within 45 secondsor the vehicle will shut down.

OR

Quick Reference GuideDBALL2-SUBARU3

© 2017 Directed. All rights reserved.

Button(s) Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock.

Press & hold for 1 second to remote

start.

Press & hold for 5 seconds to activate

the trunk release (optional).

Press once, then to activate the

rear hatch/tail glass release (optional).*

Press 3 times, then to activate

the panic mode.

Press once, then to reset the

remote starter runtime.

List of Available Commands

x1 +

x3 +

x1 +

* This output is configurable. see your authorized installation center for more information.

Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.

Notes

OR

platform: dball2 firmware subaru:3 › documents › ...® subaru is a registered trademark and...

Documents