platform: dball/dball2 firmware: tl1 rev.: 20150430...apr 30, 2015 · toyota tundra (key)...

Door lock and transponder override firmware for specific Toyota, Lexus, Scion and Pontiac vehicles. It is compatible with models that use the RX/TX immobilizer lines at key switch and with select PTS models.

Installation Guide

Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.

Vehicle Application Guide................................................................................................................................................

OEM Remote Starter Detection.......................................................................................................................................

InstallationType 1..............................................................................................................................................................................Wiring Reference Chart - Type 1.....................................................................................................................................Type 2..............................................................................................................................................................................Type 2 with T-Harness TLTH1.........................................................................................................................................Wiring Reference Chart - Type 2.....................................................................................................................................Type 3..............................................................................................................................................................................Type 3 with T-Harness TLTH1.........................................................................................................................................Wiring Reference Chart - Type 3.....................................................................................................................................Type 4..............................................................................................................................................................................Wiring Reference Chart - Type 4.....................................................................................................................................Type 5..............................................................................................................................................................................Wiring Reference Chart - Type 5.....................................................................................................................................Type 6..............................................................................................................................................................................Wiring Reference Chart - Type 6.....................................................................................................................................

ProgrammingModule Programming Type 1 (Key-type vehicles)................................................................................................................................. Types 2 & 3 (PTS-type vehicles)........................................................................................................................ Type 4 (Key-type vehicles without CAN)............................................................................................................ Type 5 (PTS-type vehicles without CAN)........................................................................................................... Type 6 (PTS-type Toyota Prius)..........................................................................................................................Module Reset...................................................................................................................................................................Hard Reset.......................................................................................................................................................................Feature & Option List.......................................................................................................................................................Feature Programming......................................................................................................................................................

LED Diagnostics & Troubleshooting.................................................................................................................................Limited One-Year Consumer Warranty............................................................................................................................

Quick Reference Guide...................................................................................................................................................

02

04

0506070809101112131416171819

202121222223232424

2526

27

Index

® Toyota and Lexus are registered trademarks and property of their respective companies.

- No takeover feature is available for Push-to-Start vehicles.- If there is no immobilizer, the module will not work (that also includes door lock controls).

WARNING

Rev.: 20150430

Platform: DBALL/DBALL2Firmware: TL1

© 2015 Directed. All rights reserved.

Vehicle Application Guide

The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.

Vehicles

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

PK

-Im

mobili

zerB

ypass

-Data

No

Key

Req'd

DL-A

rmF

act

ory

Secu

rity

DL-D

isarm

Fact

ory

Secu

rity

DL-D

oorLock

Control

DL-D

oorU

nlo

ck

DL-D

rive

rP

riority

Unlo

ck

DL-H

atc

hG

lass

Rele

ase

DL-T

runk

/Hatc

hR

ele

ase

EIP

S

RS

-Tach

/RP

MO

utp

ut

SS

-Entry

Monito

ring

ALL

DoorP

ins

SS

-Entry

Monito

ring

Drive

rD

oorP

in

SS

-Entry

Monito

ring

Hood

Pin

SS

-Entry

Monito

ring

Tru

nk/

Hatc

hP

in

SS

-Fact

ory

Ala

rmT

riggerM

onito

ring

ST

-Bra

keS

tatu

s(footb

rake

)

ST

-Hand

Bra

keS

tatu

s

ST

-Igniti

on

Sta

tus

Lexus

ES 330 4 4 4 •ES 350 (Smart Key) 3 3 3 3 3 3 • • • • • • • • • • • • • D • • •GS 300 (Smart Key) 5 •GS 350 (Smart Key) 5 5 •GS 430 (Smart Key) 5 5 •GS 450h (Smart Key) 5 5 •GS 460 (Smart Key) 5 •GX 470 4 4 4 4 4 4 4 •IS 250 (Smart Key) 5 5 5 •IS 350 (Smart Key) 5 5 5 •IS F (Smart Key) 5 •LS 430 4 4 4 •LS 460 (Smart Key) 5 5 •LS 600h (Smart Key) 5 •LX 470 4 4 4 4 4 •RX 330 4 4 4 •RX 350 4 4 4 •RX 400h 4 4 4 •Pontiac

Vibe 1 1 • • • • • • • • • • • D • • •Vibe 4 •Scion

tC 4 4 4 4 4 4 •xB 1 1 1 • • • • • • • • • • • D • • •xD 1 1 1 • • • • • • • • • • • D • • •

Legend:D: Data-to-Data (D2D) only•: D2D & Wire-to-Wire (W2W)

AV: Horn & Lights ControlsDL: OE Door Lock & Alarm ControlsEIPS: Engine Idle Protection SystemPK: Transponder & Immobilizer OverrideRS: Remote Start & Engine ControlsSS: Integrated Security & MonitoringST: Function/Feature Status

Note: Keyless and Smart-Key will remain functional during remote start.

Go to the next page to see the Toyota Vehicle Application Guide.

- No takeover feature is available on Push-to-Start vehicles.

- If equipped, the OE remote starter must be removed before installation. See page 4 for more information.

Rev.: 20150430



Vehicle Application Guide

Vehicles

20

13

20

12

20

11

20

10

20

09

20

08

20

07

20

06

20

05

20

04

20

03

PK

-Im

mo

biliz

er

Byp

ass-D

ata

No

Ke

yR

eq

'd

DL

-Arm

Fa

cto

ryS

ecu

rity

DL

-Dis

arm

Fa

cto

ryS

ecu

rity

DL

-Do

or

Lo

ck

Co

ntr

ol

DL

-Do

or

Un

lock

DL

-Dri

ve

rP

rio

rity

Un

lock

DL

-Ha

tch

Gla

ss

Re

lea

se

DL

-Tru

nk

/H

atc

hR

ele

ase

EIP

S

RS

-Ta

ch

/R

PM

Ou

tpu

t

SS

-En

try

Mo

nito

rin

gA

LL

Do

or

Pin

s

SS

-En

try

Mo

nito

rin

gD

rive

rD

oo

rP

in

SS

-En

try

Mo

nito

rin

gH

oo

dP

in

SS

-En

try

Mo

nito

rin

gT

run

k/H

atc

hP

in

SS

-Fa

cto

ryA

larm

Tri

gg

er

Mo

nito

rin

g

ST

-Bra

ke

Sta

tus

(fo

otb

rake

)

ST

-Ha

nd

Bra

ke

Sta

tus

ST

-Ig

nitio

nS

tatu

s

Toyota

4Runner 4 4 4 4 4 4 4 4 •

Avalon 4 4 4 4 4 •

Avalon (Smart Key) 5 5 5 5 •

Camry 1 1 1 1 1 • • • • • • • D • • • • • D • •

Camry 4 4 4 4 •

Camry (Smart Key) 3 3 3 3 3 • • • • • • • • D • • • • • D • •

Camry Hybrid 3 3 3 3 3 • • • • • • • • D • • • • • D • •

Corolla 1 1 • • • • • • • D • • • • • D • •

Corolla 4 4 4 4 •

Corolla (Smart Key) 2 2 2 2 2 • • • • • • • • D • • • • • D • •

FJ Cruiser 4 4 4 •

Highlander 1 1 1 • • • • • • • D • • • • • D • •

Highlander 4 4 4 4 •

Highlander (Smart Key) 3 3 3 3 3 3 • • • • • • • • D • • • • • D • •

Highlander Hybrid 3 3 3 3 3 3 • • • • • • • • D • • • • • D • •

Highlander Hybrid 4 4 •

Land Cruiser 4 4 4 4 4 •

Land Cruiser (Smart Key) 5 5 5 •

Matrix 1 1 • • • • • • D • • • • • D • •

Matrix 4 4 4 4 •

Prius (Smart Key) 6 6 6 6 6 6 •

RAV4 1 1 1 1 1 • • • • • • D • • • • • D • •

RAV4 4 4 •

RAV4 (Smart Key) 2 2 2 2 • • • • • • • D • • • • • D • •

Sequoia 4 4 4 •

Sienna 4 4 4 4 4 4 4 •

Solara 4 4 4 4 4 4 •

Tacoma 4 4 4 4 4 4 •

Tundra 4 4 4 4 • • • • • • D • • • • D • •

Venza 4 •

Yaris 4 4 4 4 4 4 •

Standard Key G-stamped keys H-stamped keysFor vehicles with G-stamped key, see TL4,TL5 or TL7 firmware. TL1 works only withstandard key.

For vehicles with H-stamped key, no solution isavailable at this time. TL1 works only withstandard key.

Key TypeSome Toyota 2010+ models have different encryption types. Please look at your key blade and identify the markings. A dot “.” means the vehicle is compatible with TL1 firmware. “G” or “H” indicates the vehicle is not compatible with this firmware.

H

Note: Keyless and Smart-Key will remain functional during remote start.

- No takeover feature is available on Push-to-Start vehicles.

- If equipped, the OE remote starter must be removed before installation. See page 4 for more information.

Rev.: 20150430



Rev.: 20150430



Vehicle OEM Remote Starter & Connector Location

Toyota Camry (key) 2007-2010 Behind Glove Box & Passenger kick panel

Toyota Corolla (key) 2009-2010 Behind Glove Box & Passenger kick panel & Junction Box & Steering column

Toyota Highlander (key) 2007-2010 Behind Glove Box & Steering column

Toyota Matrix (key) 2009-2010 Junction Box & Behind Glove Box & Passenger kick panel

Pontiac Vibe (key) 2009-2010 Behind Glove Box & Junction Box & Passenger kick panel

Scion xB (key) 2008-2010 Behind Glove Box & Passenger kick panel & Junction Box & Steering column

Scion xD (key) 2008-2010 Behind Glove Box & Passenger kick panel & Junction Box & Steering column

Toyota Rav4 (key) 2006-2010 Behind Glove Box & Passenger kick panel & Junction Box & Steering column

Toyota Sequoia (key) 2008-2010 Behind Glove Box & Passenger kick panel & Steering column

Toyota Tundra (key) 2007-2010 Behind GloveBox & Passenger kick panel & Steering column

Toyota Yaris (key) 2006-2010 Behind Glove Box & Junction Box & Steering column

Toyota Corolla (Smart Key) 2009-2013 Behind Glove Box & Passenger kick panel & Junction Box & Steering column

Toyota Rav4 (Smart Key) 2009-2012 Behind Glove Box & Junction Box

Toyota Camry (Smart Key) 2007-2011 Behind Glove Box & Passenger kick panel

Toyota Camry Hybrid (Smart Key) 2007-2011 Behind Glove Box & Passenger kick panel

Toyota Highlander (Smart Key) 2008-2013 Behind Glove Box & Passenger kick panel

Toyota Highlander Hybrid (Smart Key) 2008-2013 Behind Glove Box & Passenger kick panel

OEM Remote Starter Detection

If the Vehicle is Equipped with an OEM Remote Starter

How to Know if the Vehicle is Equipped with an OEM Remote Starter

1- An “ENGINE STARTER” sticker should be on the remote.

2- Remote start the OEM remote starter:Press the remote control’s lock button twice within 2 seconds, then press and hold the lock button for 3 seconds.

The parking lights flash after 3 seconds. The engine starts and the parking lights flash repeatedly for 20 seconds.

ENGINESTARTER

x2 &Press & Holdfor 3 seconds

If the vehicle is equipped with an OEM remote starter, the DBALL LED will start flashing orange to indicate its detection. To skip bypass and use convenience only, press the programming button 5 times.* The reason for this is to allow aftermarket security to be installed while keeping the factory remote starter active. If you wish to use DBALL to control the remote start sequence, the factory remote starter must be disconnected before programming the DBALL as both modules cannot coexist.

Locating the OEM Remote Starter

* The DBALL LED turns ON solid orange for 3 seconds after programming or power up to indicate the bypass is not active. Refer to LED Diagnostics & Troubleshooting section for more information.

Connect toIgnition Connector

Visit our websitewww.directechs.comfor more information.

(+) Ignition (some vehicles require 2 ignition)

White Connector At headlight switch

12345678910

1112131415161720 19

DiagnosticConnector at OBDII(connector side view)

1 8

169

Installation Type 1

[1] (AC) Tach Input

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

Rem

ote

Sta

rter

(-) GWR (Status)

(-) Lock Output

(-) Unlock Output

(-) Trunk Output(+) 12V

(-) Hood Status Input

(-) Ground(-) Ground

(+) Brake Input

1: Green: (-) Lock Input

2: Blue: (-) Unlock Input

3: Red/White: (-) Trunk Input

9: Pink: (+) Ignition Input

10: Blue/White: (-) GWR (Status) Input

HS CAN High: Tan/Black: 3

HS CAN Low: Tan: 4

Autolight Shutdown: Orange/Red: 10

Autolight Shutdown: Yellow/Red: 11

[1] (AC) Tach Output: Violet/White: 5

(+) Brake Output: Gray: 6

(-) E-Brake Status Output: Black/White: 1

(-) Door Status Output: Green/White: 3

(-) Trunk Status Output: Red/Black: 4

TX: Yellow/Black: 10RX: Orange/Black: 11

(-) Hood Status Output: Blue/Red: 12

HS CAN High: pin 6

HS CAN Low: pin 14

TX: pin 5

RX: pin 4

12347 6 5

Black Connectorat immobilizer

See page 6 for help on locating key components in the vehicle and wiring reference chart.

(+) 12V: Red: 13(+) 12V

(-) Ground (-) Ground: Black: 14

(+) Start (some vehicles require 2 start)

Autolight:pin 19

Not required in D2D mode.

[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.

Scion XD and Toyota Yaris headlight switch

21 3 4

5 6 7 8 9 10 11 12 13

18

See page 6 to determine the right connector for

your vehicle.

OR

DBALL/DBALL2

RF

Prog. Button

LED

4

TX

(-) Ground

RX(+)12V

14

12

2

10

P#: XKD2D65

(-) Parking Lights

With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

(+) Accessory (some vehicles require 2 accessories)

Rev.: 20150430



Rev.: 20150430



Wiring Reference Chart - Type 1

Locating Key Componentsin the Vehicle

ImmobilizerHeadlight

switch

Wire function Connector Pin position Wire color

CAN High Diagnostic connector 6 Light Green

CAN Low Diagnostic connector 14 White

Autolight

Parking Lights Headlight Switch 18 Brown

RX Immobilizer 4 Light Blue

TX Immobilizer 5 Beige



Autolight

Parking Lights Headlight Switch 18 White

RX Immobilizer 4 Light Blue


CAN High Diagnostic connector 6 Violet


Autolight


RX Immobilizer 4 Green

TX Immobilizer 5 Violet

CAN High Diagnostic connector 6 Black


Autolight Headlight Switch 19 Green

Parking Lights Headlight Switch 18 Black

RX Immobilizer 4 Brown

TX Immobilizer 5 Red



Autolight

Parking Lights Headlight Switch 18 Brown or White

RX Immobilizer 4 Light blue or Pink

TX Immobilizer 5 Beige or Green

CAN High Diagnostic connector 6 Blue



Parking Lights Headlight Switch 18 Light Blue

RX Immobilizer 4 Red

TX Immobilizer 5 Light blue



Autolight

Parking Lights Headlight Switch 18 Brown

RX Immobilizer 4 Light blue


CAN High Diagnostic connector 6 Black




RX Immobilizer 4 Pink

TX Immobilizer 5 Green

Toyota Rav4

(Key)

2006-2010

Pontiac Vibe

(Key)

2009-2010

Scion xB

(Key)

2008-2010

Scion xD

(Key)

2008-2010

Not equipped

Not equipped

Not equipped

Not equipped

Not equipped

Toyota Camry

(Key)

2007-2011

Toyota Corolla

(Key)

2009-2010

Toyota Highlander

(Key)

2008-2010

Toyota Matrix

(Key)

2009-2010

Rev.: 20150430




1 8

169

Installation Type 2a (without T-Harness)

Rem

ote

Sta

rter

(-) GWR (Status)

(-) Lock Output

(+) Ignition Input

(+) Starter Output

(-) Unlock Output

(-) Trunk Output





8: Violet: (+) Starter Input



HS CAN Low: Tan: 4

(+) 12V Input: Brown: 7

[2] : Yellow: 8(+) STSW Output

(+) 12V: Red: 13

(-) Ground: Black: 14



(+) Ignition Status Output: Gray/Black: 7

(-) Push-to-Start Output: Green/Black: 2



CAN High: pin 6

CAN Low: pin 14

(-) Parking Lights: pin 18

(-) Push-to-Start: pin 7

ENGINESTARTSTOP

BlackConnector

Connection required only if Pit-Stop/ Idle mode is desired (see details on page 9).

[1] (AC) Tach Input




(-) Parking lights

(+) 12V

(-) Ground

(+) Brake Input



White Conn.at Fuse Box

(+)12V: Black, pin 11

D o n o t c o n n e c t a n y o t h e r accessory, ignition or starter wires from the remote starter to the vehicle. The interface module is handling the required vehicle power and start sequence.

[2] STSW: Starter Switch Wire.

(-) Ground

(+) 12V

(-) Ground



1 5 4 3 1

81112 10 914

6

13

27

White ConnectorAt headlight switch12345678910

1112131415161720 19 18


DBALL/DBALL2

RF

Prog. Button

LED

4

TX

(-) Ground

RX(+)12V

14

12

2

10

XKD2D65


White Connectorat Main body ECU


[2] (+) STSW: pin 4 or 6

1 2 3 5 6 7

8 9 10 11 12 13 14

15 16 1 17 8 19

4

Rev.: 20150430



Installation Type 2b (with T-Harness TLTH1)

Diagnostic Connector at OBDII

(connector side view)

1 8

169

TLTH1(optional)

Rem

ote

Sta

rter



[1] STSW: Starter Switch Wire.


[1] : Yellow: 8(+) STSW Output[1] (+) STSW: pin 4


1 5 4 3 1

81112 10 914

6

13

2ENGINESTARTSTOP 7

BlackConnector

Connection required only if Pit-Stop/ Idle mode is desired (see details on page 9).

DBALL/DBALL2

RF

Prog. Button

LED

4

2

10

14

12

For the 12-pin and 10-pinconnectors, use the harnesses that are provided with the DBALL.

TX

(-) Ground

RX(+)12V

P#: XKD2D65









(-) GWR (Status)

(-) Lock Output

(+) Starter Output

(-) Unlock Output

(-) Trunk Output


(-) Parking Lights

(+) 12V(-) Ground(-) Ground

White ConnectorAt headlight switch

12345678910

1112131415161720 19 18

(+) Ignition InputWhite Connectorat Main body ECU


(+)12V: Black, pin 1

1

[1] (AC) Tach Input(-) Trunk Status Input

(-) Door Status Input(-) E-Brake Status Input

(+) Brake Input








1 2 3 5 6 7

8 9 10 11 12 13 14

15 16 1 17 8 19

4

Rev.: 20150430



Pit-Stop/Idle ModeThe Pit-Stop/Idle feature allows the vehicle to remain running after leaving the vehicle.Refer to the owner's guide of your remote starter for more details.


WARNING- No takeover feature is available on Push-to-Start vehicles. See Quick Reference Guide (QRG) at the end of this guide.- To remote start the engine, all doors must be closed, including rear hatch.


CAN High Diagnostic Connector 6 Light Green

CAN Low Diagnostic Connector 14 White

Autolight

Parking Lights Headlight Switch 18 Brown or White

Push-to-Start PTS button 7 White

STSW* Main Body ECU (E52) 4 Black or White

12V Fuse Box (2G) 1 White

CAN High Diagnostic Connector 6 Black




Push-to-Start PTS button 7 White

STSW* Main Body ECU (E17) 4 Red

12V Fuse Box (1G) 1 White

*STSW: Starter Switch Wire

Toyota RAV4

(Smart Key)

2009-2012

Toyota Corolla

(Smart Key)

2009-2013

Not equipped

Rev.: 20150430



DiagnosticConnector at OBDII

1 8

169

Installation Type 3a (without T-Harness)

[1] (AC) Tach Input




Rem

ote

Sta

rter

(-) GWR (Status)

(-) Lock Output

(+) Ignition Input

(+) Starter Output

(-) Aux1 Output

(-) Unlock Output

(-) Trunk Output [3]

(+) 12V

(-) Ground

(+) Brake Input








HS CAN Low: Tan: 4

(+) 12V Input: Brown: 7

[2] (+) STSW Output: Yellow: 8

(+) 12V: Red: 13






HS CAN High:pin 6

HS CAN Low:pin 14

(-) Parking Lights

[2] (+) STSW:pin 4 or 6




(+)12V Black wirepin 1

1

White Conn.At back of main body ECU

(-) Ground

(+) 12V

(-) Ground





ENGINESTARTSTOP

BlackConnector

1 5 4 3 1

81112 10 914

6

13

27


DBALL/DBALL2

RF

Prog. Button

LED

4

TX

(-) Ground

RX(+)12V

14

12

2

10

P#: XKD2D65

[2] STSW: Starter Switch Wire. Refer to the wiring reference chart on page 12 for wire color and connections.




Connection required only if Pit-Stop/ Idle mode is desired.


White Conn.At headlight switch

12345678910

1112131415161720 19 18


12

356

78910

4

Rev.: 20150430




1 5 4 3 1

81112 10 914

6

13

2ENGINESTARTSTOP 7

BlackConnector

Connection required only if Pit-Stop/ Idle mode is desired.

Installation Type 3b (with T-Harness TLTH1)

[2] STSW: Starter Switch Wire. Refer to the wiring reference chart on page 12 for wire color and connections.


1 8

169

DBALL/DBALL2

RF

Prog. Button

LED

[2] (+) STSW Output: Yellow: 8

4

2

10

14

12

For the 12-pin and 10-pinconnectors, use the harnesses that are provided with the DBALL.


Rem

ote

Sta

rter


TX

(-) Ground

RX(+)12V

P#: XKD2D65

(-) Ground (-) Ground(+) 12V(+) 12V

(+) Ignition Output


(-) Parking Lights




[1] (AC) Tach Input



TLTH1(optional)







(-) GWR (Status)

(-) Lock Output

(+) Starter Output

(-) Unlock Output

(-) Trunk Output

(+) Ignition Input









(+) Brake Input



White Connectorat headlight switch

12345678910

1112131415161720 19 18

White Conn.At main body ECU

12

356

78910

4

[2] (+) STSW:pin 4 or 6

Rev.: 20150430




CAN High Diagnostic Connector 6 Light Green

CAN Low Diagnostic Connector 14 Pink

Autolight Headlight Switch 19 Yellow


Push-to-Start PTS button 7 Blue

STSW* Main Body ECU (E58) 4 or 6 Red or Violet

12V Fuse Box (DA) 1 White






STSW* Main Body ECU (E9) 4 or 6 Gray or Violet

12V Fuse Box (1A) 1 Black






STSW* Main Body ECU (E9) 4 Gray






Push-to-Start PTS button 7 Pink

STSW* Main Body ECU (D10) 4 Pink






Push-to-Start PTS button 7 Pink

STSW* Main Body ECU (D10) 4 Yellow


*STSW: Starter Switch

Toyota Camry

Hybrid

(Smart Key)

2007-2011

Toyota Camry

(Smart Key)

2007-2011

Lexus ES 350

(Smart Key)

2007-2012

Toyota

Highlander

(Smart Key)

2008-2013

Toyota

Highlander

Hybrid

(Smart Key)

2008-2013


Pit-Stop/Idle ModeThe Pit-Stop/Idle feature allows the vehicle to remain running after leaving the vehicle.Refer to the owner's guide of your remote starter for more details.

WARNING- No takeover feature is available onPush-to-Start vehicles. See QuickReference Guide (QRG) at the endof this guide.

- To remote start the engine, all doorsmust be closed, including rear hatch.

Push-To-StartButton

Headlightswitch

Rev.: 20150430



Installation Type 4

(+) 12V(+) 12V

See pages 14-15 for help on locating key components in the vehicle and wiring reference chart.

Connect to vehicleVisit our website :

www.directechs.comfor more information.

Autolight



(-) Keysense Output: Yellow: 8

(-) Ground: Brown: 7(-) Ground

TX: Yellow/Black: 10

RX: Orange/Black: 11TX: pin 5 RX: pin 4

12347 6 5

Black 7-pin Connectorat immobilizer

(+) 12V: Red: 13(+) 12V

(-) Ground (-) Ground: Black: 14


DBALL/DBALL2

RF

Prog. Button

LED

4

TX

(-) Ground

RX(+)12V

14

12

2

10

P#: XKD2D65


Autolight: Orange/Red: 10

Autolight: Yellow/Red: 11

Black ConnectorClutch

21Lt. Green: pin 1

(+) Ignition (some vehicles require 2 ignitions)

(+) Starter 1 Output

Rem

ote

Sta

rter

(-) GWR (Status)


(+) Start 2 (some vehicles require 2 start)

[1] (AC) Tach Input

(+) Brake Input

(-) Lock Output

(-) Unlock Output

(-) Trunk Output

Connect toIgnition ConnectorVisit our website :


(-) Parking Lights Output(+) Accessory (some vehicles require 2 accessories)

Automatic Transmission:Connect to vehicle’s starter.

Manual Transmission:Connect to vehicle’s clutch.

OR

(+) Starter

ONLY for Manual Transmission vehicles.

Rev.: 20150430





Wire

functionConnector Pin position Wire color

Autolight Headlight Switch 12 White

RX Immobilizer 4 Green/White

TX Immobilizer 5 Blue/Yellow

Autolight Headlight Switch 12 Green/Orange

RX Immobilizer 4 Yellow

TX Immobilizer 5 Yellow/Black

Autolight

RX Immobilizer 4 Red/White

TX Immobilizer 5 Blue/Black


RX Immobilizer 4 Blue/Black

TX Immobilizer 5 Violet/Green

Autolight Headlight Switch 12 Brown

RX Immobilizer 4 Light Green

TX Immobilizer 5 Brown








RX Immobilizer 4 Pink/Green

TX Immobilizer 5 Light Green/Yelllow

Autolight Headlight Switch 19 Orange

RX Immobilizer 4 Lt.Green



RX Immobilizer 4 Green/White

TX Immobilizer 5 Blue/Yellow

Autolight

RX Immobilizer 4 Blue


Autolight


TX Immobilizer 5 Light Green/Red

Autolight Headlight Switch 12 Pink

RX Immobilizer 4 Gray

TX Immobilizer 5 White


RX Immobilizer 4 Blue/Black

TX Immobilizer 5 Violet/Green

Autolight



Autolight

RX Immobilizer 4 Blue/Red

TX Immobilizer 5 Pink


RX Immobilizer 4 Yellow or Green/White

TX Immobilizer 5Yellow/Red or

Blue/Yellow



TX Immobilizer 5 Blue

Autolight

RX Immobilizer 4 YellowTX Immobilizer 5 Yellow/Red

Autolight

Parking Lights Headlight Switch 18 Green


TX Immobilizer 5 Lt. Green/Red

Toyota

Corolla (Key)

2005-2008

Toyota Highlander

(Key)

2004-2007

Toyota Matrix

(Key)

2005-2008

Toyota Land Cruiser

(Key)

2003-2007

Toyota FJ Cruiser

(Key)

2007-2009

Not Equipped

Not Equipped

Not Equipped

Not Equipped

Toyota Sienna

(Key)

2004-2010

Not Equipped

Toyota RAV4

(Key)

2004-2005

Lexus ES 330

(Key)

2004-2006

Lexus GX 470

(Key)

2003-2009

Lexus LS 430

(Key)

2004-2006

Toyota Camry

(Key)

2003-2006

Toyota 4Runner

(Key)

2003-2009

Lexus LX 470

(Key)

2004-2006

Lexus RX 330

(Key)

2004-2006

Lexus RX 350

(Key)

2007-2009

Lexus RX400h

(Key)

2006-2008

Not Equipped

Toyota Tacoma

(Key)

2005-2010

Not Equipped

Toyota Avalon

2005-2010

Toyota Sequoia

(Key)

2008-2010

Toyota Solara

(Key)

2004-2009

ImmobilizerHeadlightswitch

Rev.: 20150430



Wiring Reference Chart - Type 4 (cont’d)


Immobilizer


Autolight



Autolight



Autolight

RX Immobilizer 4 Yellow

TX Immobilizer 5 Red

Pontiac Vibe

(Key)

2008

Not Equipped

Scion tC

(Key)

2005-2010

Not Equipped

Not EquippedToyota Yaris

(Key)

2006-2011

Headlightswitch

Rev.: 20150430



Do not connect any other accessory, ignition or starter wires from the remote starter to the vehicle. The interface module is handling the required vehicle power and start sequence.

Installation Type 5

Rem

ote

Sta

rter

(-) GWR (Status)

(+) Ignition Output/Input

(+) Starter Output




(+) Brake Activation Output: Yellow: 8

Data TX: Yellow/Black: 10

(-) Push-To-Start Output: Green/Black: 2

Data RX: Orange/Black: 11



ENGINESTARTSTOP

BlackConnector

(+) 12V


(+) Brake Input

Brake Switch

(-) Ground

(+) 12V: Brown: 7

(+) 12V: Red: 13(+) 12V

1 5 4 3 1

81112 10 914

6

13

27


DBALL/DBALL2

RF

Prog. Button

LED

4

TX

(-) Ground

RX(+)12V

14

12

2

10

P#: XKD2D65

142

3



TX: pin 9

RX: pin 10

Note: the OEM alarm arm/disarmwires will also control the door locks.You need to configure the remote starterto unlock the doors before start,and relock after start or turn ON feature called Safelock which is found in many Directed Premium Remote Start Systems.

Parking Lights

AC Tach Input

(-) Trunk Output


(+) Brake: pin 1

(+) Brake Output: Orange/Yellow: 9


(+) Ignition: pin 3

(-) Hood Input

This connection is required to shut the Remote Start down when the Driver’s Door is open.

(-) Driver’s Door Trigger

Hood Pin

Rev.: 20150430



Locating Key Componentsin the VehicleWire function Connector Pin position Wire color

Push-To-Start PTS Button 7 Pink

RX PTS Button 10 Yellow

TX PTS Button 9 Blue

Brake Brake Switch 1 Red/Black

















Push-To-Start PTS Button 7 Black

RX PTS Button 10 Light Blue











Push-To-Start PTS Button 7 White

RX PTS Button 10 White

TX PTS Button 9 Orange

Brake Brake Switch 1 Blue

Push-To-Start PTS Button 7 White


TX PTS Button 9 Orange


Push-To-Start PTS Button 7 Blue


TX PTS Button 9 Gray

Brake Brake Switch 1 White

Toyota Avalon

(Smart Key)

2008-2010

Lexus GS 300

(Smart Key)

2006

Lexus GS 350

(Smart Key)

2007-2008

Lexus GS 430

(Smart Key)

2006-2007

Lexus GS 450h

(Smart Key)

2007-2008

Lexus LS 600h

(Smart Key)

2008

Lexus GS 460

(Smart Key)

2008

Lexus IS 350

(Smart Key)

2006-2008

Lexus IS 250

(Smart Key)

2006-2008

Lexus IS F

(Smart Key)

2008

Lexus LS 460

(Smart Key)

2007-2008


BrakeSwitch

Push-To-StartButton

Rev.: 20150430



(+) 12V


(+) Brake Input

Brake Switch

142

3

Parking Lights

AC Tach Input

(-) Trunk Output

Installation Type 6


Rem

ote

Sta

rter

(+) Brake Activation Output: Yellow: 8

(-) Push-To-Start Output: Green/Black: 2

(+) 12V: Red: 13


(-) Push-to-Start: Yellow, pin 7

Key Release:Pink, pin 5

(-) Key Sense:Blue, pin 3

ENGINESTARTSTOP

BlackConnector

(+) 12V

(-) Ground

DBALL/DBALL2

RF

Prog. Button

LED

4

TX

(-) Ground

RX(+)12V

14

12

2

10

P#: XKD2D65

TX: Yellow/Black: 10

RX: Orange/Black: 11

TX: Lt. Green, pin 5

RX: Blue, pin 4

12347 6 5

Black 7-pin Connectorat key port

Black 5-pin Connectorat key port

(+) 12V

30

86 8587

87a

(+) 12V: Brown: 7




(-) GWR (Status)

(+) Ignition Output/Input

(+) Starter Output

1 2 3 4 5 6 7 8

1 2 3 4 5



Note: the OEM alarm (if equipped)will arm/disarm with the lock/unlockwires. You need to configure the remote starter to unlock the doors before start, and relock after start.


(+) Brake: pin 1

(+) Brake Output: Orange/Yellow: 9

(+) Ignition: pin 3

(-) Hood Input

(-) Driver’s Door Trigger

This connection is required to shut the Remote Start down when the Driver’s Door is open.

Hood Pin

Rev.: 20150430



Locating Key Components in the Vehicle


Push-To-Start PTS Button 7 Yellow

RX Black 7-pin at keyport 4 Blue

TX Black 7-pin at keyport 5 Light Green


Prius

2004-2009


BrakeSwitch

Push-To-StartButton

Module Programming

Refer to the LED Diagnostics section on page 24 for more information and for troubleshooting purposes.

1Solid

Wait until the LED turns ON solid red.

Method for Installation Type 1 vehicles: Key-type vehicles with CAN

2

3 Turn ignition to ON position. The LED turns ON solidgreen for 3 seconds then turns OFF.

IGN

ON

OF

F

KEY

Flashes Redslowly

Go to the next page to see the Types 2, 3 & 4 module programming.

Insert the key in the ignition switch. The LED flashes red slowly for a few seconds to indicate the key is in learning mode. The LED turns ON solid green.*

* If the LED starts to flash orange, it indicates the vehicle is equipped with a factory remote starter. Refer to LED Diagnostics & Troubleshooting section for more information.

&Solid Green

Solid Green3 secs.

Off

&&

&

ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.

Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit available functions and features.

1. Connect the interface module to your computer using the XKLoader.

2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top left corner of the page.

3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.

4. In the search result page, select Flash Standard install, and follow the instructions provided on the screen.5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.6. The following message will be displayed when the upload is completed:

“The flashing is successfully completed. You may now unplug the kit.”You can now proceed with the programming instructions below.

OR

If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.

D2D Installation

W2W Installation

If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.

10-pinD2D

st1

12-pin14-pin

nd2

rd3

10-pinD2D

st1

th4

12-pin14-pin

nd2

rd3

KEY ACC

ON

OF

F

4 The module is now programmed. Remove the key from the ignition. ACC

ON

OF

F

KEY

Rev.: 20150430



Module Programming

Method for Installation Types 2 & 3 vehicles: Push-To-Start (PTS) vehicles with CAN

Solid Greenx3 secs.

Flashes Redslowly2

Press the PTS button twice to turn the ignition ON. The LED flashes red slowly for few seconds to indicate the key is in learning mode. The LED turns ON solid green for 3 seconds, and then shuts OFF*.

* If the LED starts to flash orange, it indicates the vehicle is equipped with a factory remote starter. Refer to LED Diagnostics & Troubleshooting section for more information.

3 The module is now programmed, press the PTS button once more to turn the ignition OFF.

ENGINESTARTSTOP

PUSH 1X

ENGINESTARTSTOP

PUSH 2X

Off

& &

&

Method for Installation Type 4 vehicles: Key-type vehicles without CAN

2 IGN

ON

OF

F

KEY

Flashes Redslowly

Insert the key in the ignition switch. The LED flashes red slowly for few seconds to indicate the key is in learning mode then the LED turns ON solid green.

&Solid Green

&

You have successfully completed the module programming sequence.

Go to the next page to see the Type 5 module programming.

4 The module is now programmed. Remove the key from the ignition.ACC

ON

OF

F

KEY


Press the IPB 5 times to skip the CAN programming. The LED will turn OFF quickly then the green LED will turn ON for 3 seconds.

Solid Greenx3 secs.

Solid Greenx3 secs.

Off

& &&Press 5x

3

Rev.: 20150430



Module Programming

Method for Installation Type 5 vehicles: Push-To-Start (PTS) vehicles without CAN

Open the OEM key fob and remove the battery, then place the OEM key fob in front of the PTS button.2

Flashes Redslowly

Solid Green

3Press the PTS button twice to turn the ignition ON. The LED flashes red slowly for few seconds to indicate the key is in learning mode, then the LED turns ON solid green.


ENGINESTARTSTOP

PUSH 1X

ENGINESTARTSTOP

PUSH 2X & &


RemoveBattery

HOLD

Solid Greenx3 secs.

Solid Greenx3 secs.

Off

& &&Press 5x

4Press the IPB 5 times to skip the CAN programming. The LED will turn OFF quickly then the green LED will turn ON for 3 seconds.

Method for Installation Type 6 vehicles: Toyota Prius 2004-2009 with Push-To-Start

Open the OEM key fob and remove the battery, then place the OEM key fob in the key port.2

Flashes Redslowly

Solid Green

3Press the PTS button twice to turn the ignition ON. The LED flashes red slowly for few seconds to indicate the key is in learning mode. Wait until the LED turns ON solid green.


ENGINESTARTSTOP

PUSH 1X

ENGINESTARTSTOP

PUSH 2X

Off

& &

&


RemoveBattery

HOLD

Rev.: 20150430



2

Solid

&

Solid Flashes

&

Release

3

Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.

Release the programming button. The LED turns ON solid red.

Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.

1 OR

If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.

D2D Installation

If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

st1

12-pin14-pin

nd2

th4

rd3

10-pinD2D

st1

th5

12-pin14-pin

nd2

rd3

th4

Module Reset

Hard Reset

2 & &Solid SolidRelease

Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.

1 OR

If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.

D2D Installation

If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

st1

12-pin14-pin

nd2

th4

rd3

10-pinD2D

st1

th5

12-pin14-pin

nd2

rd3

th4

Rev.: 20150430



Feature & Option List

* Default option

Feature Operation Flashes / Option Description

1. Disabled* Module is connected to a remote starter using a standard installation.

2. RFTD OutputModule is connected to an XL202 using an RSR or RXT installation (when

available).

3. SmartStartModule is connected to SmartStart using an RSR or RXT installation (when

available).

1. Driver Priority*Unlocks only the driver door on first press and unlocks all doors on a second

press within 5 seconds.

2. All Unlocks all doors on first press.

1. Disabled

2. Trunk*

3.Tail Glass Opening

1. Disabled

2. Trunk

3. Tail Glass Opening*

1. Disabled

The OEM alarm will not be controlled by DBALL upon remote start. No disarm

or arm command will be executed at the beginning or end of the sequence; it

must be controlled by the Remote Starter.

2. Normal

Smart OEM Alarm Control will behave like a standard Safelock feature on a

remote starter. It will unlock at the beginning of the sequence, and relock after

start and shutdown.

3. Smart OEM Alarm Control*

Smart OEM Alarm Control will synchronize with the OEM alarm so that it will

disarm and rearm the vehicle in the remote start sequence, only when

required. The reason for this is, factory alarm control must often be done by

lock or unlock operation. This could create unnecessary actions on door lock

modules, such as the horn to honk. When possible, Smart OEM Alarm

Control will monitor the alarm and door lock status to detect if the disarm or

rearm is required. If the vehicle is unlocked or is not equipped with factory

alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will

also monitor the remote starter actions so that the factory alarm control is not

done twice. A remote starter, for which the Safelock feature is active, will work

perfectly with this option and will make it invisible to the user.

5 Smart OEM Alarm Control

Unlock Driver Priority2

1 RF Output Type

Trunk

Aux1

3

4

1. Disabled: doesn't operate any function in the vehicle.

3.Tail Glass Opening: When available, will operate the tail glass.

2. Trunk: Will pop the trunk if available.

It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page.

To enter feature programming routine- For vehicles that are not Push-to-Start (PTS), use the key to turn the ignition ON, then OFF. For PTS vehicles, press the button twice to turn the

ignition ON, then press it once more to turn it OFF. - Within 5 sec, press and HOLD the programming button. The orange LED turns ON after 3 seconds. Release the button.- The green LED starts flashing slowly one time to indicate the feature number is 1. After a short delay, the red LED flashes rapidly to indicate the

current option of feature 1. It repeats until next action happens.

Changing feature options- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. - The red LED flashes rapidly the number of times equal to the current option number. After a short delay, the green LED flashes slowly the number of

times to indicate the current feature. It repeats until next action happens.

Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The green LED flashes slowly the number of times equal to the feature number. After a short delay, the red LED flashes rapidly to indicate the

current option of the current feature. It repeats until next action happens.

When the maximum number of feature or option is reached, the LED will starts flashing again from the first feature or option.

Once a feature is programmed- Another feature(s) can be programmed.- The feature programming can be exited.

Exiting feature programming- No activity for 30 seconds; after 30 seconds, the orange LED will turn ON for 2 seconds to confirm exiting.

OR- Press and HOLD the for 3 seconds. After 3 seconds, the orange LED will turn ON for 2 seconds to confirm exiting.programming button

Feature ProgrammingProgramming

Button

Rev.: 20150430



Rev.: 20150430



LED Diagnostics & Troubleshooting

Solid

Solid

Flashes

Flashesslowly

Solid x3 secs

Solid x3 secs

Off

Flashes

Flashes

Flashes quickly

Flashes x1

Flashes x2

Flashes x3

Flashes x4

Flashes x5

LED Status Description TroubleshootingProgramming the Module

Off Module has no power.

Make sure the D2D harness is connected or that the 12 Volt is

present between the red and black wires. If the 12 Volt is present,

the module may be defective.

Solid RedWaiting to begin the

programming sequence.

Refer to the wiring diagram to make sure that all the connections

are correct.

Solid GreenCan not connect. Wating for 5x

IPB

Refer to the wiring diagram to make sure that CAN connections

are correct.

Flashes Red

slowlyLearning Mode Normal operation.

Flashes Orange OEM remote starter detected.

If the user wants to use the module as a convenience only, he

should skip bypass by pressing the programming button 5 times.

However, if the user wants to use the module as a remote starter,

he should disconnect the OEM remote starter and repeat the

programming sequence.

Solid Green x3

seconds

Module has been successfully

programmed.Normal operation.

Solid Orange x3

seconds

Module was successfully

programmed without bypass

(convenience only).

Normal operation. An OEM remote starter was detected

(convenience mode only). If the user wants to use the module as

a remote starter, he should disconnect the OEM remote starter

and repeat the programming sequence, by doing a short reset.

Active Ground While Running

Flashes GreenGROUND OUT ON (GWR)

command received.

Otherwise, the Ground While Running (status) signal was lost or

was never received by the module. Commands can come from

RF, D2D or W2W.

Flashes Red &

Orange

IGNITION ON command

received.

Otherwise, the ignition signal was not received by the module. In

a W2W install, it will show only if the ignition input wire is used.

Flashes Green

QuicklySTART ON command received.

Otherwise, the start signal was not received by the module.

Refer to the wiring diagram to make the right connections.

D2D & W2W Commands

Flashes Orange

x1Lock command received.

Flashes Orange

x2Unlock command received.

Flashes Orange

x3Trunk command received.

Flashes Orange

x4AUX1 command received.

Flashes Orange

x5AUX2 command received.

If the bypass module fails to flash, it means the module did not

receive the signal. Commands can come from RF, D2D or W2W.

For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

Limited One Year Consumer Warranty

Rev.: 20150430



Vehicle Takeover for Push-To-Start vehicles

Quick Reference GuideDBALL/DBALL2-TL1


Note: Takeover feature is not available on Push-to-start vehicles. The engine will stop when a door is opened.

Engine Idle Protection System (EIPS)

Vehicles equipped with RFID-type Push-to-Start ignition systems work by detecting a proximity key in the vehicle. They will run indefinitely if the key is removed, which could potentially lead users to exiting the vehicle while the engine is still running and the car is left idling on its own in a garage or a confined space.

To mitigate risk, we have designed a feature that is now available on the DBALL. It will detect the presence of the RFID fob in the vehicle, through the CAN bus. If left idling for more than the pre-defined runtime (i.e. 1 to 5 minutes) without detecting the fob, DBALL will send a signal to the vehicle in order to shut off the engine.

EIPS (Engine Idle Protection System) will:

Notify the user about the idling engine by sounding the horn with a series of short beeps.

Shut down the engine after a pre-defined period of time (i.e. 1 to 5 minutes). EIPS is configured using XpressVIP. The following window is displayed whenever a DBALL module is flashed.

If the engine fails to shut down due to some malfunction, EIPS will go into alarm mode and will notify the user by all means possible (e.g. horn or siren).

Button(s) Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock.

Press & hold for 1 second to remote

start.

Press & hold for 5 seconds to activate

the trunk release (optional).

Press once, then to activate the

rear hatch/tail glass release (optional).*

Press 3 times, then to activate

the panic mode.

Press once, then to reset the

remote starter runtime.

List of Available Commands

x1 +

x3 +

x1 +

* This output is configurable. see your authorized installation center for more information.

Quick Reference GuideDBALL/DBALL2-TL1


Activating/deactivating EIPS:

To activate EIPS, remove all keys from the vehicle and close all doors while the engine is running.

To deactivate EIPS, do one of the following actions:

Open one of the doors. Remote start the vehicle. Turn the engine off. Drive the vehicle.*

* The EIPS feature is disabled if the vehicle is in motion so there is no risk that the vehicle will shut off while driving, regardless of the fob being present in the vehicle or not.

Notes

platform: dball/dball2 firmware: tl1 rev.: 20150430...apr 30, 2015 · toyota tundra (key)...

Documents