nexans euromold interface d 600 series cable connectors
TRANSCRIPT
Catalogue 2015
a Nexans company
1
05/2
015
While every care is taken to ensure that the information contained in this publication is correct, no legal responsibility can be accepted for any inaccuracy. Nexans Network Solutions N.V. - Div. Euromold reserves the right to alter or modify the characteristics of its products described in this catalogue as standards and technology evolve.
EUROMOLDEuromold is the leading European specialised designer, manufacturer and distributor of prefabricated cable accessories for medium voltage energy distribution. Euromold provides a complete range of accessories for underground cables: premoulded EPDM rubber connectors for cables and epoxy bushings for transformers and switchgear, as well as a large range of cold-shrinkable terminations and joints from 12 to 42 kV.Euromold is also the manufacturer of electrical components for the high voltage accessories of the Nexans group.
ISO 9001 CertificateSince 1992, Euromold’s commitment to quality is demonstrated by its ISO 9001 certification.
International standardsAll our products meet the International standards like CENELEC HD 629.1, CENELEC EN 50180, IEC 60137, IEC 60502-4… or country speci-fications. Official certificates, CESI, KEMA, ATEX… prove the conformity of our products. Long duration tests of existing or new products are continuously performed in our test fields.
Nexans Network SolutionsDiv. Euromold
COMPANY PRESENTATION
Laboratory accreditationSince June 2000, Euromold’s independent ELAB laboratory obtained the BELAC accreditation no.144-TEST conform with the European standards for laboratories ISO 17025 for electrical testing of low and medium voltage cable accessories according to the international standards EN 50393, IEC 60502-4, IEC 61442 and HD 629.
2
05/2
015
SEPARABLE CONNECTORSAND BUSHINGS
INTERFACE D
Table of contents676LRA - tee connector670AR-2 - equipment bushing672T1 - equipment bushing672TBC - in-air bushingAccessoriesPossible arrangements
Interface D1 & D2Dimensions according to European CENELEC EN 50180 and 50181 (in mm).
81±0.2
Dia. 76.2±0.2
14.8min
29min
Dia. 39.9±0.2
Dia. 32nominal
Dia. 52.1±0.2
0-0.51.5
M16 x 2 - 6H
In mm.
3 05/2
015
Connecting possibilities
(K)680CPConnecting plu g
one cable to
equipment
(K)676LRA(/G)Tee connector
(K)606DR-TPS Dead-end receptacle
676SNStud + nut
(K)676BIPABasic insulating plug
(K)670AR-2Equipment bushing
(K)672TBCIn-air bushing
(K)672T1Equipment bushing
(K)606SOPStand-off plu g
606GPEarthing plu g
(K)676RTPAReducing tap plug
(K)675BE Bushing extender
(K)680CP Connecting plug
676SA Stud
in-line junction
cable
earthing
cable
isolation
tap-off
1250/250 A
dead-ending
of connector
connector standing
away from equipment
CONNECTION BUSHINGS / ACCESSORIES
CONNECTORS / ACCESSORIES
Equipment interface dead-ending
of equipment
4
05/2
015
Specifications and standardsThe separable connector 676LRA meets the requirements of CENELEC HD 629.1.
Up to 24 kV - 1250 A
Separable connector
type
VoltageUm(kV)
CurrentIr
(A)
Conductor sizes (mm2)
min. max.
676LRA/G
K676LRA/G
12
24
1250
1250
50
35
630
630
DesignSeparable connector comprising: 1. Conductive EPDM insert. 2. Conductive EPDM jacket. 3. Insulating EPDM layer moulded between the insert and the jacket. 4. Type D - 1250 A interface as described by CENELEC EN 50180 and 50181. 5. Conductor connector. 6. Basic insulating plug (with VD point). 7. Cable reducer. 8. Conductive rubber cap. 9. Threaded stud. 10. Earthing lead.
The screen break designenables cable outer sheathtesting without removing ordismantling the connector.
676LRAINTERFACE D
TEE CONNECTOR
ApplicationSeparable tee connector designed to connect polymeric insulated cable to equipment (transformers, switchgear, motors...).Also connects cable to cable, using the appropriate mating part.
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV
Technical characteristics• A thick conductive EPDM
jacket provides a total safe to touch screen.
• Each separable connector is tested for AC withstand and partial discharge prior to leaving the factory.
4 9
1
2
3
10
7
250 mm
212 mm
355 mm
865
5
Conductor sizes (mm2)
Aluminium conductor Copper conductor
DINhexagonal
Deepindent
DINhexagonal
35
50
70
95
120
150
185
240
300
400
500
630
35(K)M-12-2
50(K)M-12-2
70(K)M-12-2
95(K)M-12-2
120(K)M-12-2
150(K)M-12-2
185(K)M-12-2
240(K)M-12-2
300(K)M-12-2
400(K)M-12-2
500(K)M-12-2
–
35KM-12-1
50(K)M-12-1
70(K)M-12-1
95(K)M-12-1
120(K)M-12-1
150(K)M-12-1
185(K)M-12-1
240(K)M-12-1
300(K)M-12-1
400(K)M-12-1
500(K)M-12-1
630(K)M-12-1
35(K)M-11-2
50(K)M-11-2
70(K)M-11-2
95(K)M-11-2
120(K)M-11-2
150(K)M-11-2
185(K)M-11-2
240(K)M-11-2
300(K)M-11-2
400(K)M-11-2
500(K)M-11-2
630(K)M-11-2
Kit contentsThe complete (K)676LRA tee connector kit comprises the following components:
The kit also comprises lubricant, wipers,
installation instructions and crimp chart.
Ordering instructionsSelect the part numberwhich gives the best centring to the cable core insulation diameter.Add a 'K' for use up to 24 kV.
Orderingpart number
Dia. over core insulation (mm)
min. max.
676LRA/G-15-X676LRA/G-19-X676LRA/G-22-X676LRA/G-27-X676LRA/G-32-X676LRA/G-37-X676LRA/G-43-X
16.0
20.0
23.5
28.5
34.0
39.0
45.5
22.0
26.5
31.0
37.5
42.5
48.5
56.0
Example:The copper wire screened cable is 24 kV, 630 mm2 stranded aluminium with a diameter over core insulation of 44.0 mm.Order a K676LRA/G-37-630KM-12-1 tee connector kit.
For use withother cable types.
Please contact our representative.
For outdoorapplications.
Order: +MWS.
Components can be ordered individually.
Table X
For use withcopper tape
screened cables. Order: Kit MT.
For use with Alupe orC 33-226 cables.
Please contact our representative.
Connector housing
(K)650BLR/G
Threaded
stud + nut
676SN
Conductor
contact
TBC-X
Basic insulating
plug +
rubber cap
(K)676BIPA
Cable reducer
611CA-W
(K)676LRA/G-W-Xconnector kit
Table W
For use in potentially explosive atmospheres
(for 12 kV max.). Order: -/ATEX.
6
05/2
015
In mm.
Equipmentbushing
type
VoltageUm(kV)
CurrentIr
(A)
670AR-2K670AR-2
1224
12501250
6/10 (12) kV6,35/11 (12) kV
8,7/15 (17,5) kV12/20 (24) kV
12,7/22 (24) kV
Up to 24 kV - 1250 A
670AR-2INTERFACE D
EQUIPMENT BUSHING
ApplicationFor use in equipment insulated with oil fluid, typically for transformers, switchgear, capacitors...
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
Ordering instructionsTo order the equipment bushing, specify the type.The bushings can be supplied with an earth jumper (/J) or an earth plate (/GS). This earth connection must be specified when ordering.E.g. K670AR-2/GS.
Specifications and standardsThe bolted type equipment bushings 670AR-2 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 60137.
10
Dia. 70Dia. 100Dia. 150
40
140
325
36
130
M16
Minimum oil level:-12 kV: 40 mm-24 kV: 50 mm
Dia.32
7
670AR-2/GS Bushing 670AR-2/J Bushing
FIXINGS FOR EQUIPMENT BUSHINGS
Fixing dimensions standards NF C 52-053French standards.
In mm.
Bushing clamping kitTo order the bushing clamping kit, according to NFC 52-053standards, simply specify KBCNF-400.Contents: - 4 x claw clamp NF - 1 x sealing gasket.
Bushing clamping kitTo order the bushing clamping kit with DIN style fixing flange, simply specify KBCDS-400.Contents: - 1 x fixing flange DIN style - 6 x stud clamp F DIN 42 538 - 1 x sealing gasket.
Fixing dimensions
Dia. 105Dia. 171
Min. 60Max. 30
6 fixingstuds
M12M10 orM12
Dia. 105Dia. 171
Min. 55Max. 25
4 fixingstuds
NF C 52-053claw clamp
earth plate
bushing interface
fixing studs
equipment
equipmentconnection
sealing gasket
earth jumper
F DIN 42 538stud clamp
fixing flange
8
05/2
015
672T1INTERFACE D
EQUIPMENT BUSHING
Up to 24 kV - 1250 A
Equipmentbushing
type
VoltageUm (kV)
CurrentIr
(A)
672T1
K672T1
12
24
1250
1250
ApplicationFor use in equipment insulated with oil fluid, typically for transformers, switchgear, capacitors...
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV
DesignThe equipment bushing is amoulded epoxy insulated part inaccordance with CENELEC EN50180.
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
Ordering instructionsTo order the equipment bushing, specify the type.For use in potentially explosive atmospheres (for 12 kV max.). Order: -/ATEX.
Specifications and standardsThe bolted type equipment bushings 672T1 meet the requirements of IEC 60137.
Dia. 76
M16
1.5
Dia. 114
221
350
Dia.32
32
stainless steel flange
M16
Minimum oil level: -12 kV: 40 mm -24 kV: 50 mm
In mm.
9
672T1 bushing
In mm.
140
170
60°
60°
10
equipmentconnection
fixing studs andnuts M10
sealing gasket
equipment
fixing flangetype : MK600-1(antimagnetic)
bushing interface
FIXINGS FOR EQUIPMENT BUSHINGS
Bushing fixing flangeTo order the bushing fixing flange, simply specify MK600-1.
10
05/2
015
672TBCINTERFACE D
EQUIPMENT BUSHING
Up to 24 kV - 1250 AApplicationFor use in equipment insulated with air, typically for transformers, switchgear, capacitors...
Technical characteristics Each bushing is tested forAC withstand and partial discharge prior to leavingthe factory.
DesignThe equipment bushing is amoulded epoxy insulated part inaccordance with CENELEC EN50181.Non-tracking insulating rubberboot and collars slip over thebushing shank.
Specifications and standardsThe bolted type equipment bushings 672TBC meet the requirements of IEC 60137.
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV
Equipmentbushing
type
VoltageUm(kV)
CurrentIr
(A)
Creepage distanceA-B
(mm)
672TBC
K672TBC
12
24
1250
1250
300
300
In mm.
M16
1.5
221
350
Dia. 114
Dia. 85
stainless steel flange
boot and collars
in EPDM
32
A
B M16
Dia. 120
Dia. 32
Ordering instructionsTo order the equipment bushing, specify the type.For use in potentially explosive atmospheres (for 12 kV max.). Order: -/ATEX.
11
In mm.
equipmentconnection
fixing studs andnuts M10
sealing gasket
equipment
fixing flangetype : MK600-1(antimagnetic)
bushing interface
10
140
170
60°
60°
672TBC bushing
FIXINGS FOR EQUIPMENT BUSHINGS
Bushing fixing flangeTo order the bushing fixing flange, simply specify MK600-1.
12
05/2
015
ACCESSORIESINTERFACE D
Up to 24 kVApplicationFor use with connectors and bushings with an interface D as described by CENELEC EN 50180 and 50181.
Technical characteristics All these products, except theearthing plug, are tested forAC withstand and partial discharge prior to leavingthe factory.
606SOPStand-off plugIs designed to support and 'dead-end' connectors with a type D interface when removed from equipment.
Ordering instructionsOrder 606SOP for 12 kV orK606SOP for 24 kVapplications.
606GPEarthing plugIs designed to support and earth connectors with a type D interface when removed from equipment.
Ordering instructionsOrder 606GP for 12 or 24 kVapplications.
606DR-TPSDead-end receptacleFits over a bushing with a type D interface to provide 'dead-end' facility.Contains a capacitive test point for checking circuit conditions.
Ordering instructionsOrder606DR-TPS for 12 kV orK606DR-TPS for 24 kVapplications.The dead-end receptacle canbe supplied with an earth lead.Order: -/G.E.g. 606DR-TPS/G.
6/10 (12) kV6.35/11 (12) kV
8.7/15 (17.5) kV12/20 (24) kV
12.7/22 (24) kV
13
Kit MTEarthing kit for copper tape screened cablesContains a tinned copper braid (25 mm² - L = 500 mm), a tinned copper wire for cleating and water sealing mastic.
Ordering instructionsOrder Kit MT for 12 kV or 24 kV applications.
676RTPAReducing tap plugProvides a type A interface to connectors with a type D interface.A 'C' spanner, 600SW, is used to tighten the reducing tap plug onto its mating part.
Ordering instructionsOrder 676RTPA for 12 kV orK676RTPA for 24 kVapplications.Order 600SW for the 'C'spanner.
680CPConnecting plugFor connecting two or more connectors with a type D interface together, thus creating a separable cable joint or a multiple cable connection to equipment.
Ordering instructionsOrder 680CP for 12 kV orK680CP for 24 kVapplications.Order: -/ATEX for use in potentially explosive atmospheres (for 12 kV max.).
676BIPABasic insulating plugActs as a tightening nut for the 676LRA/G tee connector kits.The plug contains a voltage detection point.The conductive rubber protection cap is included.
Ordering instructionsOrder 676BIPA for 12 kV orK676BIPA for 24 kVapplications.
675BEBushing extenderProvides an extension piece to allow cables to stand away from equipment. Is used in conjunction with the 680CP connecting plug.
Ordering instructionsOrder 675BE for 12 kV orK675BE for 24 kVapplications.
14
05/2
015
POSSIBLE ARRANGEMENTSINTERFACE D
676LRA/GSingle cable arrangement.Order 676LRA/G for 12 kV or K676LRA/G for 24 kV applications.
676LRA/G-P2Dual cable arrangement.Order 676LRA/G-P2 for 12 kV or K676LRA/G-P2 for 24 kV applications.
676LRA/G-P4Single cable arrangement with tap-off.Order 676LRA/G-P4 for 12 kV or K676LRA/G-P4 for 24 kV applications.
676LRA/G-P3Triple cable arrangement.Order 676LRA/G-P3 for 12 kV or K676LRA/G-P3 for 24 kV applications.
In mm.
basic insulating
plug
250
106
connecting plug
106
470
225
basic insulating
plug
695
225
connecting plug
connecting plug
basic insulating
plug
106 225
460
106 235
tap-off plug
type A separable connector
15
285
basic insulating
plug
basic insulating
plug
676LRA/G-P5Dual cable arrangement with tap-off.Order 676LRA/G-P5 for 12 kV or K676LRA/G-P5 for 24 kV applications.
676LRA/G-L1Dead-ending.Order 676LRA/G-L1 for 12 kV or K676LRA/G-L1 for 24 kV applications.
676LRA/G-P6Connector standing away from equipment.Order 676LRA/G-P6 for 12 kV or K676LRA/G-P6 for 24 kV applications.
In mm.
676LRA/G-L22-way connection.Order 676LRA/G-L2 for 12 kV or K676LRA/G-L2 for 24 kV applications.
676LRA/G-L44-way connection.Order 676LRA/G-L4 for 12 kV or K676LRA/G-L4 for 24 kV applications.
676LRA/G-L33-way connection.Order 676LRA/G-L3 for 12 kV or K676LRA/G-L3 for 24 kV applications.
690
connecting plug
tap-off plug
type A separable connector
106 235 225
470
331
connecting plug
basic insulating
plug bushing extender
505
basic insulating
plug
basic insulating
plug
connecting plug
955
basic insulating
plug
basic insulating
plug
connecting plug
connecting plug
connecting plug
730
basic insulating
plug
basic insulating
plug
connecting plug
connecting plug
16
In mm.
676LRA/G-L52-way connection with tap-off.Order 676LRA/G-L5 for 12 kV or K676LRA/G-L5 for 24 kV applications.
676LRA/G-L63-way connection with two tap-offs.Order 676LRA/G-L6 for 12 kV or K676LRA/G-L6 for 24 kV applications.
676LRA/G-L73-way connection with one tap-off.Order 676LRA/G-L7 for 12 kV or K676LRA/G-L7 for 24 kV applications.
676LRA/G-L84-way connection with two tap-offs.Order 676LRA/G-L8 for 12 kV or K676LRA/G-L8 for 24 kV applications.
500
basic insulating
plug
tap-off plug
type A separable connector
710
tap-off plug
tap-off plug
type A separable connector
type A separable connector
plu g
725
basic insulating
plug
tap-off plug
type A separable connector
connecting plug
935
tap-off plug
tap-off plug
type A separable connector
type A separable connector
connecting plug
17
In mm.
676LRA/G-L94-way connection with one tap-off.Order 676LRA/G-L9 for 12 kV or K676LRA/G-L9 for 24 kV applications.
Connector on earthing plugOrder 606GP for 12 kV and 24 kV applications.
Connector on stand-off plugOrder 606SOP for 12 kV or K606SOP for 24 kV applications.
945
basic insulating
plug
type A separable connector
connecting plug
connecting plug
tap-off plug
basicinsulating
plugstand-off
plugearthing
plug
basicinsulating
plug
18
05/2
015
NOTES
19
20
05/2
015
Additional catalogue information on power cable accessoriesis available by contacting us at the address below:
Distributed by:
a Nexans company
Nexans Network Solutions N.V. - Div. Euromold Zuid III, Industrielaan 12, B-9320 Erembodegem
Tel.: +32 (0)53 85 02 11 • [email protected] • www.euromold.be
Catalogue also available on CD-ROM, Website and Mobile Apps