miele product manual - sirv...miele cannot be held liable for injury or damage caused by...

Operating instructions

Cordless stick vacuum cleaner

AUS, NZ

M.-Nr. 11 579 120

HS19

Contents

2

Warning and Safety instructions ..................................................................... 4

Caring for the environment .............................................................................. 11

Guide to the appliance ...................................................................................... 12Installation and connection .............................................................................. 14Assembling the vacuum cleaner ......................................................................... 14Connecting the Comfort handle .......................................................................... 14Connecting the PowerUnit and the suction tube ................................................ 15Inserting the battery ............................................................................................ 16Connecting the Electrobrush............................................................................... 17General battery information................................................................................. 17Charging the battery (without wall mounting)...................................................... 18Charging the battery (with wall mounting)........................................................... 18Wall mounting...................................................................................................... 19Attaching the mounting plate .............................................................................. 20Attaching the charging cable to the wall bracket ................................................ 20Connecting the accessories holder (if required).................................................. 21Connecting the wall bracket................................................................................ 21Battery charging state indicator (while charging) ................................................ 22Battery charging state indicator (while in use)..................................................... 22

Using the accessories supplied ....................................................................... 23Electrobrush Multi Floor XXL (SEB 430 or SEB 435)........................................... 23Electro Compact handheld brush (SEB 23)......................................................... 24Additional AP01 battery and LS03 charger cradle .............................................. 24

Use ...................................................................................................................... 25Switching on and off ........................................................................................... 25Regulating the suction power ............................................................................. 25Illuminating the work area ................................................................................... 25Self-standing function for short pauses in vacuuming........................................ 25

Maintenance ...................................................................................................... 26Emptying the dust container ............................................................................... 26Cleaning the fine dust filter.................................................................................. 28Cleaning the pre-filter.......................................................................................... 28Cleaning the dust container ................................................................................ 30Cleaning the Electrobrush/handheld brush......................................................... 30Replacing the rechargeable battery .................................................................... 31

Problem solving guide ...................................................................................... 32

Error messages ................................................................................................. 34

Contents

3

Cleaning and care ............................................................................................. 35

Service................................................................................................................ 35Contact in case of malfunction ........................................................................... 35Warranty .............................................................................................................. 35

Optional accessories ........................................................................................ 36

Electrical connection ........................................................................................ 37

Warning and Safety instructions

4

It is essential to read these instructions.

This vacuum cleaner conforms to current safety requirements. In-appropriate use can lead to personal injury and damage to prop-erty.

Please read the operating instructions before using the vacuumcleaner and charging the battery for the first time. They contain im-portant information on the safety, use and maintenance of the va-cuum cleaner. This will prevent both personal injury and damage tothe appliance.

In accordance with standard IEC 60335-1, Miele expressly andstrongly advises that you read and follow the instructions in the“Installation and connection” chapter as well as the safety instruc-tions and warnings.

Miele cannot be held liable for injury or damage caused by non-compliance with these instructions.

Keep these operating instructions in a safe place and pass themon to any future owner.

Always disconnect the vacuum cleaner from the power supplywhen you have finished using it, before changing any accessories,as well as for maintenance work, cleaning and troubleshooting.Use the On/Off switch on the Comfort handle to do this.

Correct application

This vacuum cleaner is intended for cleaning flooring in domestichouseholds and similar residential environments. This vacuumcleaner is not suitable for use on construction sites.

This vacuum cleaner is not intended for outdoor use.


5

This vacuum cleaner can be used for all normal cleaning of car-pets, rugs and robust hard flooring.

This vacuum cleaner is intended for use at altitudes of up to4000 m above sea level.

The vacuum cleaner must only be used to vacuum dry floor sur-faces. Do not vacuum people or animals. Any other types of use,modifications or alterations are not permitted.

This vacuum cleaner can only be used by people with reducedphysical, sensory or mental capabilities, or lack of experience orknowledge, if they are supervised whilst using it or have been shownhow to use it in a safe way and understand and recognise the con-sequences of incorrect operation.

The packaging material protects the vacuum cleaner from trans-port damage. We recommend you keep the packaging for transportpurposes.

Safety with children

Young children must be kept away from the vacuum cleaner un-less they are constantly supervised.

Older children may only use the vacuum cleaner without supervi-sion if they have been shown how to use it in a safe manner. Chil-dren must be able to understand and recognise the possible dangerscaused by incorrect operation.

Children must not be allowed to clean or maintain the vacuumcleaner unsupervised.

Please supervise children in the vicinity of the vacuum cleaner anddo not let them play with it.

Danger of suffocation. Packaging, e.g. plastic wrappings, must bekept out of the reach of babies and children. Whilst playing, childrencould become entangled in packaging or pull it over their head andsuffocate.


6

Technical safety

The vacuum cleaner operates at 25.2 V.

It is classified as a class III appliance.This appliance is supplied by a safety extra-low voltage (SELV)power source where the voltage is low enough to protect users fromthe risk of electrical shock. A Class II charger is used for supplyingpower to charge the vacuum cleaner.

Compare the connection data on the data plate of the charger(voltage and frequency) with that of the mains electricity supply. Thisdata must match exactly. Without modifications, the charger is suit-able for 50 Hz and 60 Hz.

The mains electrical outlet must be fitted with an appropriate cir-cuit breaker.

Before using the vacuum cleaner and its accessories, check forany visible signs of damage. Do not use a damaged appliance.

The Miele Multi Floor XXL Electrobrush and the Miele Elec-tro Compact handheld brush (varies according to the model) are ad-ditional motor-driven devices designed specially for this Miele va-cuum cleaner. For safety reasons, the vacuum cleaner must not beused with a different Miele Electrobrush/handheld brush or an Elec-trobrush/handheld brush produced by another manufacturer.

Store the vacuum cleaner at an ambient temperature between0 °C and 45 °C.

Repairs should only be undertaken by a Miele authorised servicetechnician. Otherwise the warranty will be invalidated.

Repairs and other work by unqualified persons can cause consid-erable danger to users.

Miele can only guarantee the safety of the appliance when genu-ine Miele replacement parts are used. Faulty components must onlybe replaced with genuine Miele replacement parts.


7

If the vacuum cleaner is to be stored unused for a long period, thebattery should be removed.

The supply terminals must not be short-circuited.

Cleaning

Do not immerse the vacuum cleaner or any accessories suppliedwith it in water.

The Electrobrush/handheld brush (depending on the model), thePowerUnit, the suction tube, the body and the Comfort handle con-tain electrical wires. The plug connectors must not come into con-tact with water. Danger of electric shock. They should only becleaned with a dry cloth.

Clean the vacuum cleaner and accessories only with a dry orslightly damp cloth when disconnected from the power supply. Ex-ception:

- Dust container: empty the dust container and remove the pre-fil-ter. Clean the dust container using water and mild washing-up li-quid only. Then dry the dust container carefully. Replace the pre-filter in the dust container.

Correct use

Do not use the vacuum cleaner without the dust container, pre-fil-ter, fine dust filter and motor protection filter fitted.

Do not vacuum up anything which has been burning or is stillglowing e.g. cigarettes, ashes or coal, whether glowing or apparentlyextinguished.

Do not use the vacuum cleaner to vacuum up any water, liquid ordamp dirt. Wait until any freshly cleaned or shampooed rugs or car-pets are completely dry before attempting to vacuum.

Do not use the vacuum cleaner to vacuum toner dust. Toner, suchas that used in printers and photocopiers, can conduct electricity.


8

Do not vacuum up any inflammable or combustible liquids orgases and do not vacuum in areas where such substances arestored.

Never touch the Electrobrush/handheld brush (varies according tothe model) while it is rotating.

Do not use the Electrobrush/handheld brush (varies according tothe model) at head height.

Do not vacuum at head height and do not let the suction get any-where near a person's head.

Accessories

Only use genuine accessories with the “ORIGINAL Miele” logo onthe packaging. The manufacturer cannot otherwise guarantee thesafety of the product.

Safety instructions and warnings for AP01 battery, LG01charger, LS03 charger cradle (depending on the model)

Safety with children

People (including children) with reduced physical, sensory or men-tal capabilities, or lack of experience or knowledge, who are unableto use the LG01 charger/LS03 charger cradle safely may only usethis vacuum cleaner if they are supervised whilst using it or havebeen shown how to use it in a safe way and understand and recog-nise the consequences of incorrect operation.

Keep the AP01 battery out of the reach of children.

Children must be kept away from the LG01 charger/LS03 chargercradle unless they are constantly supervised.

Do not let children play with the chargers.


9

Technical safety

The AP01 battery, the LG01 charger and the LS03 charger cradleare designed for use with the Miele HS19 vacuum cleaner. For safetyreasons, the vacuum cleaner must not be used with a battery, char-ger or charger cradle produced by another manufacturer.

Only the LG01/xx charger or the LS03/xx charger cradle suppliedwith the vacuum cleaner can be used to charge the AP01 battery.Do not use the LG01/xx charger or LS03/xx charger cradle to chargeany other batteries.xx stands for 01, 02, 03, 04, 05, 06, 07 or 08; these numbers identifythe country version of your LG01 charger and your LS03 chargercradle:

XX

01 AT, BE, BG, CH, CL, CZ, DE, DK, EE, ES, FI, FR, GR, HR, HU, IT, KZ, LT,LU, LV, NL, NO, PL, PT, RO, RS, RU, SE, SI, SK, TR, UA, ZA

02 AE, GB, HK, IE, MY, SG

03 CA, MX, US

04 AU, NZ

05 CN

06 KR

07 JP

08 IN

If you are using a mains plug adapter, make sure that it is ap-proved for continuous operation.

Reliable and safe operation of this vacuum cleaner can only beassured if the LG01 charger/LS03 charger cradle has been connec-ted to the mains electricity supply.

Charge the vacuum cleaner at an ambient temperature between0 °C and 45 °C. During charging, the AP01 battery must be placed ina well ventilated area.


10

Stop using the AP01 battery immediately if you notice an unusualsmell from it, if liquid is leaking from it, if it is significantly overheatingor if it is discoloured or deformed. Dispose of the AP01 battery im-mediately (see safety notice “Disposing of the AP01 battery” at theend of this chapter as well as “Caring for the environment” – “Dis-posing of old batteries”).

Batteries will deplete over time. They can then leak corrosive flu-ids. Avoid contact with the eyes and skin. In the event of contact,rinse thoroughly with water and seek medical advice.

To deal with leaking batteries, refer to the Safety Data Sheet (con-tact Miele to request a copy).

Correct use

Do not drop or throw the AP01 battery. For safety reasons, do notcontinue to use an AP01 battery which has been damaged.

Keep the AP01 battery away from naked flames or other heatsources. Do not heat the AP01 battery. Do not expose the re-chargeable battery to direct sunlight.

Do not dismantle the AP01 battery.

Do not cause a short circuit by bridging the contacts of the AP01battery, either unintentionally or deliberately.

Do not allow the AP01 battery to come into contact with liquids.

Disposing of the AP01 battery: remove the AP01 battery from thevacuum cleaner. Insulate the metal contacts with adhesive tape toprevent short circuits. Dispose of the AP01 battery in a municipal re-cycling facility. Do not dispose of the AP01 battery with your house-hold waste.

The rechargeable battery must be removed before the applianceis scrapped.

Caring for the environment

11

Disposal of the packing mater-ialThe packaging is designed to protectthe appliance from damage duringtransportation. The packaging materialsused are selected from materials whichare environmentally friendly for disposaland should be recycled.

Recycling the packaging reduces theuse of raw materials in the manufactur-ing process and also reduces theamount of waste in landfill sites.

Disposing of your old appli-anceBefore disposing of your old vacuumcleaner, remove the fine dust filter anddispose of it with your householdwaste.

Electronic and electrical appliancescontain many valuable materials. Theyalso contain certain materials, com-pounds and components which wereessential for their correct functioningand safety. These could be hazardousto your health and to the environment ifdisposed of with general waste or ifhandled incorrectly. Please do not,therefore, dispose of your old vacuumcleaner with your household waste.

Instead, please make use of officiallydesignated collection and disposalpoints to dispose of and recycle elec-trical and electronic appliances in yourlocal community, with your dealer or

with Miele. Ensure that it presents nodanger to children while being storedfor disposal.

Disposing of old batteriesIn many cases, electrical and electronicappliances contain batteries whichmust not be disposed of with house-hold waste after use. You are legally ob-liged (depending on country) to removeany old batteries which are not securelyenclosed by the vacuum cleaner and totake them to a suitable collection point(e.g. retailer) where they can be handedin free of charge. Insulate the metalcontacts with adhesive tape to preventshort circuits. Batteries may containsubstances which can be hazardous tohuman health and the environment.

The labelling on the battery will providefurther information. The bin symbol witha cross through it means that the bat-teries must not be disposed of inhousehold waste. A bin with a crossthrough it which also has one or morechemical symbols on it indicates thatthe battery contains lead (Pb), cadmium(Cd) and/or mercury (Hg).

Old batteries contain valuable raw ma-terials which can be recycled. Dispos-ing of batteries separately makes themeasier to handle and recycle.

Guide to the appliance

12

Guide to the appliance

13

a Comfort handle

b Release catch for Comfort handle (on the back)

c Dust container handle

d Dust container with pre-filter, fine dust filter and motor protection filter

e PowerUnit with battery connection and connections for Comfort handle, suc-tion tube, Electrobrush and dust container

f Release catches for battery (on both sides of the battery)

g Charging socket (at the bottom of the battery)

h AP01 lithium-ion battery

i Connector

j Multi Floor XXL Electrobrush (some models feature BrilliantLight lighting)

k Removable roller brush

l Flap

m Release catch for removing the roller brush

n Release catches

o Battery charging state indicator

p Suction tube

q On/Off switch with suction power selector

14

Installation and connection

Assembling the vacuum cleaner

You can assemble the vacuum cleanerin 2 different ways.

You can place the suction tube eitherabove or below the PowerUnit.

The advantages of placing thePowerUnit at the bottom of the va-cuum cleaner are as follows:- secure self-standing function possible(see “Use” – “Self-standing function forshort pauses in vacuuming”)

- ergonomic (reduced strain on thewrist)- convenient cleaning of large surfaces

The advantages of placing thePowerUnit at the top of the vacuumcleaner are as follows:- convenient cleaning underneath fur-niture- PowerUnit can be removed quickly

PowerUnit solo

The PowerUnit can be used on its ownwithout the suction tube and Electro-brush as a quick way of vacuuming upcrumbs and lint in specific areas.

Tip: This configuration is particularlysuitable when using the three-piece ac-cessory set (see “Using the accessoriessupplied”).

Connecting the Comfort handle

Depending on how your vacuumcleaner is configured, you can connectthe Comfort handle to either the suctiontube or the PowerUnit.

15

Push the Comfort handle down on tothe suction tube connector fromabove until it audibly clicks into place(left image detail).

Slide the Comfort handle along theguide line on the dust containerhandle and down on to the PowerUnitconnector from above until it audiblyclicks into place (right image detail).

Switch off the vacuum cleaner usingthe On/Off switch on the front of theComfort handle before separating thesections.

Press the release catch and removethe Comfort handle by pulling up-wards.

Connecting the PowerUnit and thesuction tube

Depending on how your vacuumcleaner is configured, the suction tubeis located either above or below thePowerUnit.

Slide the suction tube along the guideline on the dust container handle anddown on to the PowerUnit connectorfrom above until it audibly clicks intoplace (left image detail).

Push the PowerUnit connector downon to the suction tube from above un-til it audibly clicks into place (right im-age detail).

16

Press the release catch to separatethe individual sections from eachother.

Inserting the battery

Remove the protective sticker fromthe battery.

Push the battery along the guide linesuntil it audibly clicks into place in thePowerUnit.

If you want to separate the sectionsagain, press both release catches atthe side of the battery to remove thebattery.

17

Connecting the Electrobrush

Depending on how your vacuumcleaner is configured, you can connecteither the PowerUnit connector or thesuction tube connector to the Electro-brush.

Insert the connector down into theElectrobrush from above until it aud-ibly clicks into place.

To separate the individual sectionsfrom each other, press the releasecatch on the Electrobrush and pullthe connector out of the Electro-brush.

General battery information

The rechargeable battery is suppliednot fully charged.Charge the battery completely beforeusing it for the first time. Allow approx-imately 4 hours for this.

It is essential to charge the battery forthe first time in the PowerUnit in orderto activate maximum power in the bat-tery.

Once the battery is fully charged, thebattery charging state indicatorswitches off after 10 minutes to con-serve energy.

You can use the vacuum cleaner for upto 14 minutes if you are using it in itsfully assembled state at the maximumpower level.If, however, you are using thePowerUnit on its own and select thelowest power level, you can vacuum forup to 60 minutes.

Keep batteries out of the reachof children.A swallowed battery can cause injuryand even death. Even flat batteriescan still be dangerous. If you suspecta child has swallowed a battery, seekmedical advice immediately*. Exam-ine devices and make sure the bat-tery compartment is correctly se-cured, e.g. that the screw or othermechanical fastener is tightened. Donot use if compartment is not secure.* Australia: Poisons InformationCentre, Tel. 13 11 26;NZ: National Poisons Centre,Tel. 0800 764 766

18

Charging the battery (without wallmounting)

You can store the vacuum cleaner up-right and charge the battery directly.

Connect the PowerUnit to the Elec-trobrush to provide a secure base forthe vacuum cleaner.

Swing the vacuum cleaner forwardsuntil the Electrobrush connector aud-ibly clicks into place.

Plug the supplied charging cable intothe charging socket on the bottom ofthe battery.

Plug the charger into a power socket.

The charging process will start.

You can read more about this in “Bat-tery charging state indicator”.

Charging the battery (with wallmounting)

There are 2 ways to store and chargethe vacuum cleaner in the supplied wallbracket.

You will need a suitable location neara free power socket for mounting theappliance on the wall.

19

Wall mounting

The supplied wall bracket has a mount-ing plate with a bag of screws attachedto the back.Attach the mounting plate to the pointon the wall where you want the wallmounting to be.

Remove the bag of screws.

Press the release catch at the bottomof the wall bracket.

Remove the mounting plate from thewall bracket by sliding it downwards.

20

Attaching the mounting plate

2 plugs and 2 T20 TORX screws aresupplied for attaching the mountingplate to the wall.You will also need a battery-operatedscrewdriver or a drill (with a drilling dia-meter of 6 mm).

Depending on how your vacuumcleaner is configured, select a distanceof 45 cm or 98 cm between the bottomedge of the mounting plate and thefloor.

Be careful not to damage any cableslaid in the wall.

Attach the mounting plate to the wall.

Attaching the charging cable to thewall bracket

A cable compartment is located on theunderside of the wall bracket.

Press both release catches on the un-derside of the wall bracket and re-move the cable compartment cover.

Insert the supplied charging cableinto the opening from above.

Lay the charging cable in its guide.

21

Refit the cover and close the cablecompartment.

Then turn over the wall bracket.

Connecting the accessories holder(if required)

An accessories holder is supplied forstoring the three-piece accessory set(see “Using the accessories supplied”).

Push the accessories holder on to thewall bracket as far as it will go.

Connecting the wall bracket

Slide the wall bracket down into themounting plate from above until itaudibly clicks into place.

Slide the PowerUnit of the fully as-sembled vacuum cleaner, with thebattery inserted, down into the wallbracket from above.

Plug the charger into the powersocket.

The charging process will start.

22

Battery charging state indicator(while charging)

The battery charging state is displayedon the PowerUnit.

Charging capa-city

Display

Approx. 0–34 % Bottom lightflashes slowly

Approx. 35–69 % Bottom light is litup; middle lightflashes slowly

Approx. 70–90 % Bottom andmiddle lights arelit up;top light flashesslowly

Approx. 91–100 %

Bottom, middleand top lights arelit up

Once the battery is fully charged, thebattery charging state indicatorswitches off after 10 minutes to con-serve energy.You can display the charging state for4 seconds at any time by pressing theOn/Off switch on the Comfort handle.

If the battery has not been used for along time and has run down, it will gointo a safe mode. As a result, the bat-tery charging state indicator will onlyrespond after approximately 30–60 minutes when charging in thePowerUnit.

Battery charging state indicator(while in use)

The battery charging state is displayedon the PowerUnit.

Charging capa-city

Display

Approx. 100–70 %

Top, middle andbottom lights arelit up

Approx. 69–35 % Middle and bot-tom lights are litup

Approx. 34–11 % Bottom light is litup

Approx. 10–0 % Bottom lightflashes slowly

23

Using the accessories supplied

Upholstery nozzleAccessory for cleaning upholstery,mattresses and cushions.

Crevice nozzle Accessory for cleaning in folds,crevices or corners.

Dusting brushAccessory for vacuuming skirtingboards, carved furniture or orna-ments.The head can be swivelled to ad-just the angle.

d Accessories holderFor storing the three-piece ac-cessory set.

Symbols on the holder show where toattach the different accessories.You can fit the accessories holder to thewall bracket (see “Installation and con-nection” – “Connecting the accessoriesholder”).

Electrobrush Multi Floor XXL (SEB430 or SEB 435)

Follow the flooring manufacturer’scleaning and care instructions.

The Electrobrush can be used for allnormal cleaning of carpets, rugs andhard flooring which is not susceptible toscratching.

Tip: The suction tube is not a conveni-ent option for cleaning carpeted stairs.

Miele offers a range of suitable ac-cessories for many special applica-tions (see “Optional accessories”).

24

Electro Compact handheld brush(SEB 23)

(depending on model)


The handheld brush is particularly suit-able for intensive cleaning of upholsteryand car seats.

Tip: The suction tube is not a conveni-ent option for cleaning upholstery or carseats.

Additional AP01 battery and LS03charger cradle


Using the additional battery doubles theamount of time the vacuum cleaner canbe used for.

Before charging for the first time,please note the information in “Install-ation and connection” – “General bat-tery information”.

After the battery has been fullycharged once in the PowerUnit, thecharger cradle can be used to chargeit. Push the battery into the chargercradle until it audibly clicks into place.

Insert the plug into a power socket.

The charging process will start. Thebattery charging state indicator flasheson the left.You can find out more about the batterycharging state indicator in “Installationand connection” – “Battery chargingstate indicator”.

If you place the run-down battery inthe charger cradle straight after use, itwill only start charging once the bat-tery has cooled down.The cooling process can take up to60 minutes. The battery charging stateindicator on the charger cradle will notrespond during this time.

25

Use

Switching on and off

Pull the charger out of the chargingsocket on the battery if you havecharged the battery directly.

If you have charged the battery in thewall bracket, take the vacuum cleanerout of the wall bracket.

Press the On/Off switch on the Com-fort handle .

Regulating the suction power

The suction power can be regulated tosuit the type of flooring being cleaned.Reducing the suction power reducesthe amount of effort required to man-oeuvre the Electrobrush.

There are 3 power levels to choose fromon the Comfort handle:

1 Lowest power levelfor light soiling

2 Medium power levelfor normal soiling

Max. Highest power levelfor heavy soiling

The floor covering detection function isactivated in the medium and highestpower levels.The Electrobrush power output is auto-matically set to the optimum levelbased on the type of flooring – this canlead to a change in the operating noise.

Illuminating the work area


The Electrobrush on your vacuumcleaner is equipped with BrilliantLight toilluminate the work area.

Self-standing function for shortpauses in vacuuming

(For safety reasons, this function canonly be used when the PowerUnit is fit-ted at the bottom of the vacuumcleaner)

If you are vacuuming with thePowerUnit fitted at the bottom of thevacuum cleaner, you can easily inter-rupt operation while the appliance isswitched on.

Swing the vacuum cleaner forwardsuntil the Electrobrush connector aud-ibly clicks into place.

The vacuum cleaner stays securely up-right, the Electrobrush switches itself offand the battery is conserved.If you then unlock the connector on theElectrobrush, the Electrobrush willswitch on again.

26

Maintenance

Risk of injury caused by rotatingroller brush.You can injure yourself on the rotat-ing roller brush.Switch the vacuum cleaner off beforedoing any maintenance work. Usethe On/Off switch on the Comforthandle to do this.

We recommend using only genuineMiele accessories bearing the “ORI-GINAL Miele” logo on the packaging.Only these will guarantee the optimumperformance of your vacuum cleanerand the best possible cleaning results.

Please note that faults and damagecaused by use of accessories whichdo not bear the “ORIGINAL Miele”logo on the packaging are not coveredby the vacuum cleaner warranty.

Purchasing accessories

Original Miele accessories are availablefrom the Miele Webshop, Miele andyour Miele supplier.

Original Miele accessories are identifiedby the “ORIGINAL Miele” logo on thepackaging.

Emptying the dust container

Empty the dust container before thedust has reached the max marking onthe dust container.

Turn the lid of the dust container inthe direction of the arrow as far asthe first stop.

Lift the dust container upwards to re-move it.

The contents of the container can bedisposed of with normal domesticwaste, providing they consist of gen-eral household dust only.

27

Hold the dust container close to thebin to prevent dust from billowing out.

Turn the lid of the dust container inthe direction of the arrow as far asthe next stop.

The cover at the bottom of the dustcontainer will open and the dust will fallout.

Turn the lid of the dust container backto its original position.

Close the cover making sure it clicksinto place.

Slide the dust container handle alongthe guide line and down on to thePowerUnit connector from above untilit audibly clicks into place.

28

Cleaning the fine dust filter

The fine dust filter is located in the dustcontainer.Clean the fine dust filter at least once amonth.

Remove the dust container.

Lift the fine dust filter upwards to re-move it.

Risk of damage caused by incor-rect cleaning.The fine dust filter can become dam-aged and be less effective as a res-ult.Do not clean the inside of the finedust filter. Do not use pointed orsharp-edged objects to clean the fil-ter. Do not brush the fine dust filter.

Hold the fine dust filter over a bin.

Carefully knock the rubberised loweredge of the fine dust filter.

Turn the fine dust filter slightly whileyou do this to free the dirt from all ofthe crevices.

Once it is clean, replace the fine dustfilter in its position in the dust con-tainer.

Replace the dust container on thePowerUnit connector.

Cleaning the pre-filter

The pre-filter is located in the dust con-tainer.Clean the pre-filter when required.


Remove the fine dust filter.

Empty the dust container over a binand lift the pre-filter upwards to re-move it.

29

Unlock the motor protection filter byturning it anti-clockwise and lift it up-wards to remove it.

Risk of damage caused by incor-rect cleaning.The pre-filter can become damagedand be less effective as a result.Do not use pointed or sharp-edgedobjects to clean the filter.

Carefully knock the dust out of thepre-filter over a bin.

Tip: Use a tool like a fine cleaning brushto clean the inside of the pre-filter thor-oughly.You do not need to clean the motor pro-tection filter. It can be removed so thatthe inside of the pre-filter is easier toreach.

After cleaning the pre-filter, place themotor protection filter back into thepre-filter securely, making sure it isproperly positioned.

Lock the motor protection filter byturning it clockwise as far as it will go.

Replace the pre-filter in the dust con-tainer.

To do this, line up the guide lines onthe two sections and turn the dustcontainer lid back to its original posi-tion.

Close the cover at the bottom of thedust container, making sure it clicksinto place.

Replace the fine dust filter.


30

Cleaning the dust container

Clean the dust container as required.


Empty the dust container over a binand lift the pre-filter upwards to re-move it.

Clean the dust container using waterand mild washing-up liquid.

Dry the dust container thoroughly.

Replace the pre-filter in the dust con-tainer.


Cleaning the Electrobrush/handheldbrush

(The availability of the handheld brushdepends on the model)

Separate the Electrobrush/handheldbrush from the vacuum cleaner con-nector.

Removing threads and hairs

Place the Electrobrush/handheldbrush upside down on a level, cleansurface.

Cut any threads or hairs that havewound themselves around the rollerbrush with a pair of scissors. To guidethe scissors, move along the guidetrack on the roller brush.

Then run the vacuum cleaner to va-cuum up the cut threads and hairs.

Removing the roller brush

(Not possible with the handheld brush)

You can take the roller brush out of theElectrobrush in order to remove stub-born soiling and clean the inside of theElectrobrush.

31

Unlock the cover on the side of theElectrobrush so that the symbolbecomes visible.

Lift the cover up as far as it will go.

Remove the roller brush.

Clean the roller brush and removeany stubborn dirt inside the Electro-brush.

Reassemble the Electrobrush in re-verse order.

Replacing the rechargeable battery

An original Miele AP01 lithium-ion re-chargeable battery (HX LA) is required.

Follow the instructions regarding thehandling and disposal of rechargeablebatteries found in the following sec-tions: “Warning and safety”, “Caringfor the environment” and “Installationand connection” (“General battery in-formation”).

32

Problem solving guideWith the help of the following guide, minor faults in the performance of the appli-ance, some of which may result from incorrect operation, can be remedied withoutcontacting Miele. This will save you time and money because you won't need aservice call.

Please note that a call-out charge will be applied to unnecessary service visitswhere the problem could have been rectified as described in these operating in-structions.

Risk of injury caused by rotating roller brush.You can injure yourself on the rotating roller brush.Switch the vacuum cleaner off before dealing with any problems. Use the On/Off switch on the Comfort handle to do this.

Problem Cause and remedy

The cleaning perform-ance is poor.

The dust container is full. Empty and clean the dust container.

The Electrobrush is dirty/blocked. Clean the roller brush and the inside of the Electro-

brush (see “Maintenance” – “Cleaning the Electro-brush”).

Cleaning performanceis reduced.

The fine dust filter is dirty. Clean the fine dust filter (see “Maintenance” –

“Cleaning the fine dust filter”).

The pre-filter is dirty. Clean the pre-filter (see “Maintenance” – “Cleaning

the pre-filter”).

The Electrobrushswitches itself off.

The Electrobrush is overloaded – this can happen onsurfaces like deep-pile carpet. Switch the vacuum cleaner off and switch it on

again at a reduced suction power level. Use theOn/Off switch on the Comfort handle to do this.

The operating noise ischanging during vacu-uming.

The floor covering detection function is activated inthe medium and highest power levels. The Electro-brush power output is automatically set to the op-timum level based on the type of flooring. The noise is not unusual – the vacuum cleaner is

functioning normally.

33


The vacuum cleanerdoes not start when it isswitched on.

There is no battery inserted or the battery is insertedincorrectly. Insert the battery or check how the battery is posi-

tioned (see “Installation and connection” – “Insert-ing the battery”).

The rechargeable battery is not sufficiently charged. Charge the battery exactly as described in these

operating instructions (see “Installation and con-nection” – “Charging the battery”).

An original Miele battery has not been inserted. Insert an original Miele AP01 lithium-ion re-

chargeable battery (HX LA).

The charger is still plugged in. Pull the plug out of the charging socket on the bat-

tery.

34

Error messages

Risk of injury caused by rotating roller brush.You can injure yourself on the rotating roller brush.Switch the vacuum cleaner off before dealing with any problems. Use the On/Off switch on the Comfort handle to do this.

Error messages are displayed with a quick flashing light on the battery chargingstate indicator on the PowerUnit.


Bottom light flashesquickly

Internal system error Remove the battery, wait for 10 seconds, reinsert

it and charge it.

Bottom and middlelights flash quickly

“Battery overheating” error Wait for approximately 30 minutes before switch-

ing the vacuum cleaner back on again.

Middle and top lightsflash quickly

“Battery not recognised” error Insert an original Miele AP01 lithium-ion re-

chargeable battery (HX LA).

Top light flashes quickly “Comfort handle not recognised” error Remove the Comfort handle and reconnect it (see

“Installation and connection” – “Connecting theComfort handle”).

Remove the battery, wait for 10 seconds and rein-sert it.

35

Cleaning and care

Risk of injury caused by rotatingroller brush.You can injure yourself on the rotat-ing roller brush.Switch the vacuum cleaner off beforecleaning it. Use the On/Off switch onthe Comfort handle to do this.

Vacuum cleaner and accessories

Risk of electric shock from mainsvoltage.If moisture gets into the charger,there is a risk of electric shock.Do not let the charger get wet.

Follow the special cleaning instruc-tions for the dust container in the“Maintenance” section.

The vacuum cleaner and all plastic ac-cessories can be cleaned with a propri-etary cleaner suitable for plastic.

Damage due to unsuitable clean-ing agents.All surfaces are susceptible toscratching. Contact with unsuitablecleaning agents can alter or discol-our the external surfaces.Do not use abrasive cleaning agents,glass cleaning agents, all-purposecleaners or oil-based conditioningagents.

Service

Contact in case of malfunction

In the event of any faults which youcannot remedy yourself, please contactMiele.

Contact information for Miele can befound at the end of this document.

Please note that telephone calls may bemonitored and recorded for trainingpurposes and that a call-out charge willbe applied to service visits where theproblem could have been resolved asdescribed in this booklet.

Warranty

The manufacturer's warranty for this ap-pliance is 2 years.

For more information about countryspecific warranty terms and conditions,please contact Miele.

36

Optional accessories


We recommend using only genuineMiele accessories bearing the “ORI-GINAL Miele” logo on the packaging.Only these will guarantee the optimumperformance of your vacuum cleanerand the best possible cleaning results.

Please note that faults and damagecaused by use of accessories whichdo not bear the “ORIGINAL Miele”logo are not covered by the vacuumcleaner warranty.

Purchasing accessories

Original Miele accessories are availablefrom the Miele webshop, the Miele Cus-tomer Service Department and fromyour Miele dealer.

Original Miele accessories are identifiedby the “ORIGINAL Miele” logo on thepackaging.

Certain models are supplied as stand-ard with one or more of the followingaccessories.

SEB 23 Electro Compact handheldbrush (HX SEB)

For intensive cleaning of upholstery andcar seats.

Radiator brush (SHB 30)

For dusting radiators, narrow shelvesand crevices.

Mattress nozzle (SMD 10)

For vacuuming upholstery, mattresses,cushions, curtains, covers etc.

Crevice nozzle, 300 mm (SFD 10)

Extra long crevice nozzle for cleaning infolds, crevices and corners.

Crevice nozzle, 560 mm (SFD 20)

Flexible crevice nozzle for vacuuminghard to reach places.

Additional AP01 battery (HX LA)

For doubling the amount of time the va-cuum cleaner can be used for.

LS03 charger cradle (HX LS)

For charging the additional battery inde-pendently of the appliance, i.e. whilethe appliance is in use.

37

Electrical connectionAll work should be carried out by a suit-ably qualified and competent person instrict accordance with national andlocal safety regulations. The voltageand rated load are given on the dataplate located underneath the vacuumcleaner. Please ensure that these matchthe household mains supply. The char-ger is supplied with a cable and moul-ded plug ready for connection to a230V/50Hz AC single phase supply.

Test Marks Electrical safety RCM Mark

Electrically sup-pressed according to

CISPR 14.1

Miele Experience Centre and Head Office Melbourne:1 Gilbert Park DriveKnoxfield, VIC 3180

Miele Experience Centre South Melbourne:206-210 Coventry StreetSouth Melbourne, VIC 3205

Miele Experience Centre and Office Sydney:3 Skyline PlaceFrenchs Forest, NSW 2086

Miele Experience Centre and Office Brisbane:Tenancy 4C, 63 Skyring TerraceNewstead, QLD 4006

Miele Experience Centre and Office Perth:

83-85 Sir Donald Bradman DriveHilton, SA 5033

Miele Experience Centre and Office Adelaide:

Miele Australia Pty. Ltd. Miele New Zealand Limited

Level 2, 10 College HillFreemans Bay, Auckland 1011

Miele Experience CentreAuckland:8 College HillFreemans Bay, Auckland 1011

Miele Global HeadquartersGermanyMiele & Cie. KGCarl-Miele-Straße 2933332 GüterslohFederal Republic of Germany

Head Office:

IRD 98 463 631ACN 005 635 398ABN 96 005 635 398

Miele Experience Centre Gold Coast:131 Ferry RoadSouthport, QLD 4215

Miele Experience CentreWellington:183 Featherston StreetWellington 6011

0800 464 353 (0800 4 MIELE)

www.miele.co.nz

205-207 Stirling HighwayClaremont, WA 6010

1300 464 353 (1300 4 MIELE)

www.miele.com.au

SMxxx - 1020 M.-Nr. 11 579 120 / 00

miele product manual - sirv...miele cannot be held liable for injury or damage caused by...

Documents