material safety data sheet - carquestweblink.carquest.com/msds/mmm/mmm 06080.pdf · specific use:...
TRANSCRIPT
3M MATERIAL SAFETY DATA SHEET 3M(TM) Perfect-It(TM) 3000 Paint Finishing Best Practice Kit, PNs 06080, 06081 06/21/2007
_________________________________________________________________________________________________________Page 1 of 2
Material Safety Data Sheet
Copyright, 2007, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
PRODUCT NAME: 3M(TM) Perfect-It(TM) 3000 Paint Finishing Best Practice Kit, PNs 06080, 06081
MANUFACTURER: 3MDIVISION: Automotive Aftermarket
ADDRESS: 3M CenterSt. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 06/21/2007Supercedes Date: 06/01/2007
Document Group: 23-1559-6
ID Number(s):
60-4550-3177-7, 60-4550-3178-5
This product is a kit or a multipart product which consists of multiple, independently packaged components. An MSDS for each of these components is included. Please do not separate the component MSDSs from this cover page. The document numbers of the MSDSs for components of this product are:
19-8944-1, 19-3261-5, 19-0343-4
Revision Changes:Kit: Component document group number(s) was modified.Kit initial issue message was modified.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.
3M MATERIAL SAFETY DATA SHEET 3M(TM) Perfect-It(TM) 3000 Paint Finishing Best Practice Kit, PNs 06080, 06081 06/21/2007
_________________________________________________________________________________________________________Page 2 of 2
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 SWIRL MARK REMOVER PN 6064 , PN 6065, 6053, 39019 05/23/2007
_________________________________________________________________________________________________ Page 1 of 8
Material Safety Data Sheet
Copyright, 2007, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) PERFECT-IT(TM) 3000 SWIRL MARK REMOVER PN 6064 , PN 6065, 6053, 39019
MANUFACTURER: 3MDIVISION: Automotive Aftermarket
ADDRESS: 3M CenterSt. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 05/23/2007Supercedes Date: 04/27/2006
Document Group: 19-0343-4
Product Use:Intended Use: AutomotiveSpecific Use: REMOVAL OF IMPERFECTIONS FROM PAINTED SURFACE
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by WtWATER 7732-18-5 50 - 70ALUMINUM OXIDE 1344-28-1 10 - 30DISTILLATES (PETROLEUM), ACID TREATED, LIGHT 64742-14-9 5 - 15DECAMETHYLCYCLOPENTASILOXANE 541-02-6 3 - 7DODECAMETHYLCYCLOHEXASILOXANE 540-97-6 1 - 5ALUMINUM SILICATE CLAY 66402-68-4 1 - 5
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Specific Physical Form: EmulsionOdor, Color, Grade: Petroleum distillate odor, grey viscous liquidGeneral Physical Form: Liquid Immediate health, physical, and environmental hazards: Combustible liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 SWIRL MARK REMOVER PN 6064 , PN 6065, 6053, 39019 05/23/2007
_________________________________________________________________________________________________ Page 2 of 8
May cause target organ effects.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:Mild Eye Irritation: Signs/symptoms may include redness, pain, and tearing.
Skin Contact:Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, and itching.
Inhalation:Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain.
Intentional concentration and inhalation may be harmful or fatal.
May be absorbed following inhalation and cause target organ effects.
Ingestion:Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: Do not induce vomiting. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 SWIRL MARK REMOVER PN 6064 , PN 6065, 6053, 39019 05/23/2007
_________________________________________________________________________________________________ Page 3 of 8
5.1 FLAMMABLE PROPERTIES
Autoignition temperature No Data AvailableFlash Point 168 ºF [Test Method: Closed Cup]Flammable Limits - LEL No Data AvailableFlammable Limits - UEL No Data Available
5.2 EXTINGUISHING MEDIAUse fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Combustible liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drainsand build dikes to prevent entry into sewer systems or bodies of water. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Collect as much of the spilled material as possible. Clean up residue with detergent and water. Collect the resulting residue containing solution. Place in a closed container approved for transportation by appropriate authorities. Seal the container. Dispose of collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLINGDo not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep out of the reach of children. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits. If ventilation is not adequate, use respiratory protection equipment. Keep container closed when not in use. Avoid eye contact. Avoid breathing of vapors.
7.2 STORAGEStore away from heat. Store away from oxidizing agents. Keep container tightly closed.
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 SWIRL MARK REMOVER PN 6064 , PN 6065, 6053, 39019 05/23/2007
_________________________________________________________________________________________________ Page 4 of 8
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLSUse in a well-ventilated area.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face ProtectionAvoid eye contact.The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.
8.2.2 Skin ProtectionAvoid prolonged or repeated skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials. Gloves made from the following material(s) are recommended: Neoprene, Nitrile Rubber.
8.2.3 Respiratory ProtectionAvoid breathing of vapors, mists or spray. Consult the current 3M Respirator Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges and P95 particulate prefilters. Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of SwallowingDo not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional InformationALUMINUM OXIDE ACGIH TWA, particulate
matter, < 1% crystalline silica
10 mg/m3 Table A4
ALUMINUM OXIDE CMRG TWA 1 fiber/cc ALUMINUM OXIDE OSHA TWA, respirable 5 mg/m3 Table Z-1ALUMINUM OXIDE OSHA TWA, Vacated, as
dust10 mg/m3
ALUMINUM OXIDE OSHA TWA, as total dust 15 mg/m3 Table Z-1DECAMETHYLCYCLOPENTASILOXANE CMRG TWA 10 ppm OIL MIST, MINERAL ACGIH TWA, as mist 5 mg/m3 OIL MIST, MINERAL ACGIH STEL, as mist 10 mg/m3 OIL MIST, MINERAL OSHA TWA, as mist 5 mg/m3 Table Z-1POLYETHYLENE GLYCOLS AIHA TWA, as aerosol 10 mg/m3 VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:ACGIH: American Conference of Governmental Industrial HygienistsCMRG: Chemical Manufacturer Recommended GuidelineOSHA: Occupational Safety and Health AdministrationAIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 SWIRL MARK REMOVER PN 6064 , PN 6065, 6053, 39019 05/23/2007
_________________________________________________________________________________________________ Page 5 of 8
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Specific Physical Form: EmulsionOdor, Color, Grade: Petroleum distillate odor, grey viscous liquidGeneral Physical Form: Liquid Autoignition temperature No Data AvailableFlash Point 168 ºF [Test Method: Closed Cup]Flammable Limits - LEL No Data AvailableFlammable Limits - UEL No Data AvailableBoiling point 375 ºFDensity 8.6 lb/galVapor Density No Data Available
Vapor Pressure No Data Available
Specific Gravity 0.99 [Ref Std: WATER=1]pH 7.5 - 8.5 Melting point No Data Available
Solubility in Water ModerateVolatile Organic Compounds <= 17 % weight Volatile Organic Compounds 1.17 lb/galVOC Less H2O & Exempt Solvents 375 g/lViscosity 12,000 - 16,000 centipoise [Test Method: Brookfield]
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: None known
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance ConditionFormaldehyde During CombustionCarbon monoxide During CombustionCarbon dioxide During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its components.
SECTION 12: ECOLOGICAL INFORMATION
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 SWIRL MARK REMOVER PN 6064 , PN 6065, 6053, 39019 05/23/2007
_________________________________________________________________________________________________ Page 6 of 8
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in an industrial or commercial facility. As a disposal alternative, dispose of waste product in a facility permitted to accept chemical waste.
EPA Hazardous Waste Number (RCRA): Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):60-4400-9661-2, 60-4400-9934-3, 60-9801-0913-0, 60-9801-0914-8, 60-9801-0938-7
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONSContact 3M for more information.
311/312 Hazard Categories:Fire Hazard - Yes Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - No
STATE REGULATIONSContact 3M for more information.
CHEMICAL INVENTORIESThe components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 SWIRL MARK REMOVER PN 6064 , PN 6065, 6053, 39019 05/23/2007
_________________________________________________________________________________________________ Page 7 of 8
or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.
INTERNATIONAL REGULATIONSContact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard ClassificationHealth: 1 Flammability: 2 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
Revision Changes:Section 1: Product use information was modified.Copyright was modified.Section 2: Ingredient table was modified.Section 8: Skin protection - recommended gloves information was added.Section 8: Skin protection - recommended gloves text was added.Section 8: Skin protection - protective clothing text was added.Section 8: Skin protection - recommended gloves - punctuation was added.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 SWIRL MARK REMOVER PN 6064 , PN 6065, 6053, 39019 05/23/2007
_________________________________________________________________________________________________ Page 8 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT (TM) 3000 EXTRA CUT RUBBING COMPOUND PN 6060, 6061, 6058, 39018 06/07/2007
_________________________________________________________________________________________________ Page 1 of 8
Material Safety Data Sheet
Copyright, 2007, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) PERFECT-IT (TM) 3000 EXTRA CUT RUBBING COMPOUND PN 6060, 6061, 6058, 39018
MANUFACTURER: 3MDIVISION: Automotive Aftermarket
ADDRESS: 3M CenterSt. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 06/07/2007Supercedes Date: 04/27/2006
Document Group: 19-3261-5
Product Use:Intended Use: AutomotiveSpecific Use: Removal of imperfections from painted surface.
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by WtWATER 7732-18-5 40 - 70ALUMINUM OXIDE 1344-28-1 10 - 30HYDROTREATED LIGHT PETROLEUM DISTILLATES 64742-47-8 5 - 10DECAMETHYLCYCLOPENTASILOXANE 541-02-6 3 - 7HYDROTREATED HEAVY NAPHTHA PETROLEUM 64742-48-9 1 - 5DODECAMETHYLCYCLOHEXASILOXANE 540-97-6 1 - 5GLYCERIN 56-81-5 1 - 5SOLVENT-REFINED HEAVY PARAFFINIC PETROLEUM DISTILLATES 64741-88-4 0.5 - 1.5MINERAL OIL 64741-89-5 0 - 0.5
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Specific Physical Form: EmulsionOdor, Color, Grade: Slight solvent odor, white emulsion
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT (TM) 3000 EXTRA CUT RUBBING COMPOUND PN 6060, 6061, 6058, 39018 06/07/2007
_________________________________________________________________________________________________ Page 2 of 8
General Physical Form: Liquid Immediate health, physical, and environmental hazards: Combustible liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back. May cause target organ effects.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Skin Contact:Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, and itching.
Inhalation:Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain.
Intentional concentration and inhalation may be harmful or fatal.
May be absorbed following inhalation and cause target organ effects.
Ingestion:Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: Do not induce vomiting. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get immediate medical attention.
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT (TM) 3000 EXTRA CUT RUBBING COMPOUND PN 6060, 6061, 6058, 39018 06/07/2007
_________________________________________________________________________________________________ Page 3 of 8
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature No Data AvailableFlash Point 188 ºF [Test Method: Closed Cup]Flammable Limits - LEL No Data AvailableFlammable Limits - UEL No Data Available
5.2 EXTINGUISHING MEDIAUse fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. Water may be used to blanket the fire. Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Combustible liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Collect as much of the spilled material as possible. Clean up residue with detergent and water. Place in a closed container approved for transportation by appropriate authorities. Seal the container. Dispose of collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLINGKeep out of the reach of children. Avoid eye contact. Avoid breathing of vapors, mists or spray. Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat, sparks, open flame, pilot lights and other sources of ignition. Avoid contact with oxidizing agents. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits. If ventilation is not adequate, use respiratory protection equipment.
7.2 STORAGE
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT (TM) 3000 EXTRA CUT RUBBING COMPOUND PN 6060, 6061, 6058, 39018 06/07/2007
_________________________________________________________________________________________________ Page 4 of 8
Store away from heat. Store out of direct sunlight. Store away from acids. Store away from oxidizing agents.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLSProvide ventilation adequate to control dust concentrations below recommended exposure limits and/or control dust.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face ProtectionAvoid eye contact.The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.
8.2.2 Skin ProtectionAvoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials. Gloves made from the following material(s) are recommended: Nitrile Rubber.
8.2.3 Respiratory ProtectionAvoid breathing of vapors, mists or spray.Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges and P95 particulate prefilters. Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of SwallowingDo not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional InformationALUMINUM OXIDE ACGIH TWA, particulate
matter, < 1% crystalline silica
10 mg/m3 Table A4
ALUMINUM OXIDE CMRG TWA 1 fiber/cc ALUMINUM OXIDE OSHA TWA, respirable 5 mg/m3 Table Z-1ALUMINUM OXIDE OSHA TWA, Vacated, as
dust10 mg/m3
ALUMINUM OXIDE OSHA TWA, as total dust 15 mg/m3 Table Z-1DECAMETHYLCYCLOPENTASILOXANE CMRG TWA 10 ppm GLYCERIN ACGIH TWA, as mist 10 mg/m3 GLYCERIN OSHA TWA, as mist,
respirable5 mg/m3 Table Z-1
GLYCERIN OSHA TWA, Vacated, as mist, total dust
10 mg/m3
GLYCERIN OSHA TWA, as mist, total dust
15 mg/m3 Table Z-1
HYDROTREATED HEAVY NAPHTHA PETROLEUM
3M TWA 100 ppm
HYDROTREATED HEAVY NAPHTHA PETROLEUM
CMRG TWA 300 ppm
HYDROTREATED LIGHT PETROLEUM DISTILLATES
CMRG TWA 300 ppm
OIL MIST, MINERAL ACGIH TWA, as mist 5 mg/m3
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT (TM) 3000 EXTRA CUT RUBBING COMPOUND PN 6060, 6061, 6058, 39018 06/07/2007
_________________________________________________________________________________________________ Page 5 of 8
OIL MIST, MINERAL ACGIH STEL, as mist 10 mg/m3 OIL MIST, MINERAL OSHA TWA, as mist 5 mg/m3 Table Z-1POLYETHYLENE GLYCOLS AIHA TWA, as aerosol 10 mg/m3 SOLVENT-REFINED HEAVY PARAFFINIC
PETROLEUM DISTILLATESCMRG TWA 5 mg/m3
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:ACGIH: American Conference of Governmental Industrial HygienistsCMRG: Chemical Manufacturer Recommended GuidelineOSHA: Occupational Safety and Health AdministrationAIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Specific Physical Form: EmulsionOdor, Color, Grade: Slight solvent odor, white emulsionGeneral Physical Form: Liquid Autoignition temperature No Data AvailableFlash Point 188 ºF [Test Method: Closed Cup]Flammable Limits - LEL No Data AvailableFlammable Limits - UEL No Data AvailableBoiling point 212 ºFDensity 8.7 lb/galVapor Density No Data Available
Vapor Pressure No Data Available
Specific Gravity 1 [Ref Std: WATER=1]pH 8 Melting point No Data Available
Solubility in Water NegligibleVolatile Organic Compounds 1.25 lb/gal [Test Method: calculated per CARB title 2] [Details:
(excluding exempt compounds)]Viscosity 22000 - 28000 centipoise
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: None known
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance ConditionFormaldehyde During CombustionCarbon monoxide During Combustion
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT (TM) 3000 EXTRA CUT RUBBING COMPOUND PN 6060, 6061, 6058, 39018 06/07/2007
_________________________________________________________________________________________________ Page 6 of 8
Carbon dioxide During CombustionOxides of Nitrogen During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in an industrial or commercial facility. As a disposal alternative, dispose of waste product in a facility permitted to accept chemical waste.
EPA Hazardous Waste Number (RCRA): Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):LB-K100-0349-7, 60-4100-0937-1, 60-4100-0938-9, 60-4400-9540-8, 60-4400-9967-3, 60-9801-0936-1
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONSContact 3M for more information.
311/312 Hazard Categories:Fire Hazard - Yes Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - No
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT (TM) 3000 EXTRA CUT RUBBING COMPOUND PN 6060, 6061, 6058, 39018 06/07/2007
_________________________________________________________________________________________________ Page 7 of 8
STATE REGULATIONSContact 3M for more information.
CHEMICAL INVENTORIESThe components of this product are in compliance with the chemical notification requirements of TSCA.
Contact 3M for more information.
INTERNATIONAL REGULATIONSContact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard ClassificationHealth: 1 Flammability: 2 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
Revision Changes:Section 1: Product use information was modified.Copyright was modified.Section 2: Ingredient table was modified.Section 14: ID Number(s) was modified.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT (TM) 3000 EXTRA CUT RUBBING COMPOUND PN 6060, 6061, 6058, 39018 06/07/2007
_________________________________________________________________________________________________ Page 8 of 8
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 ULTRAFINA(TM) SE PN 06068 06069 06073 06074 06076 03/26/2007
_________________________________________________________________________________________________ Page 1 of 8
Material Safety Data Sheet
Copyright, 2007, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) PERFECT-IT(TM) 3000 ULTRAFINA(TM) SE PN 06068 06069 06073 06074 06076
MANUFACTURER: 3MDIVISION: Automotive Aftermarket
ADDRESS: 3M CenterSt. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 03/26/2007Supercedes Date: 10/23/2006
Document Group: 19-8944-1
Product Use:Intended Use: AutomotiveSpecific Use: Automotive Painted Surface Swirl Mark Eliminator
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by WtWATER 7732-18-5 50 - 80DODECAMETHYLCYCLOHEXASILOXANE 540-97-6 5 - 15HYDROTREATED LIGHT PETROLEUM DISTILLATES 64742-47-8 5 - 15ALUMINUM OXIDE 1344-28-1 5 - 15SOLVENT-REFINED HEAVY PARAFFINIC PETROLEUM DISTILLATES 64741-88-4 1 - 5MINERAL OIL 64741-89-5 0 - 2FORMALDEHYDE 50-00-0 <= 0.0095
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Blue liquid. solvent odorGeneral Physical Form: Liquid Immediate health, physical, and environmental hazards: Contains a chemical or chemicals which can cause cancer. May cause target organ effects.
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 ULTRAFINA(TM) SE PN 06068 06069 06073 06074 06076 03/26/2007
_________________________________________________________________________________________________ Page 2 of 8
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Skin Contact:Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Inhalation:Intentional concentration and inhalation may be harmful or fatal.
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain.
May be absorbed following inhalation and cause target organ effects.
Ingestion:Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Carcinogenicity:Contains a chemical or chemicals which can cause cancer.
Ingredient C.A.S. No. Class Description RegulationFORMALDEHYDE 50-00-0 Group 1 International Agency for Research on CancerFORMALDEHYDE 50-00-0 Anticipated human carcinogen National Toxicology Program CarcinogensFORMALDEHYDE 50-00-0 Cancer hazard OSHA CarcinogensMINERAL OILS (UNTREATED AND
MILDLY TREATED OILS)NONE Group 1 International Agency for Research on Cancer
MINERAL OILS (UNTREATED AND MILDLY TREATED OILS)
NONE Known human carcinogen National Toxicology Program Carcinogens
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed.
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 ULTRAFINA(TM) SE PN 06068 06069 06073 06074 06076 03/26/2007
_________________________________________________________________________________________________ Page 3 of 8
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Flash Point Not Applicable
OSHA Flammability Classification: Not Applicable
5.2 EXTINGUISHING MEDIAOrdinary combustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Not applicable.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more information on handling and managing the spill. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Collect as much of the spilled material as possible. Clean up residue with detergent and water. Place in a closed container approved for transportation by appropriate authorities. Seal the container. Dispose of collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 ULTRAFINA(TM) SE PN 06068 06069 06073 06074 06076 03/26/2007
_________________________________________________________________________________________________ Page 4 of 8
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Avoid breathing of vapors, mists or spray. Keep out of the reach of children. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits. If ventilation is not adequate, use respiratory protection equipment.
7.2 STORAGEKeep from freezing.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLSUse with appropriate local exhaust ventilation. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control mist, vapor, or spray. If ventilation is not adequate, use respiratory protection equipment.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face ProtectionAvoid eye contact.The following eye protection(s) are recommended: Safety Glasses with side shields.
8.2.2 Skin ProtectionAvoid prolonged or repeated skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials. Gloves made from the following material(s) are recommended: Nitrile Rubber.
8.2.3 Respiratory ProtectionAvoid breathing of vapors, mists or spray. Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges and P95 particulate prefilters. Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of SwallowingDo not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Not applicable.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional InformationALUMINUM OXIDE ACGIH TWA, particulate
matter, < 1% crystalline silica
10 mg/m3 Table A4
ALUMINUM OXIDE CMRG TWA 1 fiber/cc ALUMINUM OXIDE OSHA TWA, respirable 5 mg/m3 Table Z-1ALUMINUM OXIDE OSHA TWA, Vacated, as
dust10 mg/m3
ALUMINUM OXIDE OSHA TWA, as total dust 15 mg/m3 Table Z-1FORMALDEHYDE ACGIH CEIL 0.3 ppm Sensitizer; Table A2FORMALDEHYDE OSHA TWA 0.5 ppm Standard AppendixHYDROTREATED LIGHT PETROLEUM
DISTILLATESCMRG TWA 300 ppm
OIL MIST, MINERAL ACGIH TWA, as mist 5 mg/m3 OIL MIST, MINERAL ACGIH STEL, as mist 10 mg/m3
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 ULTRAFINA(TM) SE PN 06068 06069 06073 06074 06076 03/26/2007
_________________________________________________________________________________________________ Page 5 of 8
OIL MIST, MINERAL OSHA TWA, as mist 5 mg/m3 Table Z-1SOLVENT-REFINED HEAVY PARAFFINIC
PETROLEUM DISTILLATESCMRG TWA 5 mg/m3
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:ACGIH: American Conference of Governmental Industrial HygienistsCMRG: Chemical Manufacturer Recommended GuidelineOSHA: Occupational Safety and Health AdministrationAIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade: Blue liquid. solvent odorGeneral Physical Form: Liquid
Flash Point Not Applicable
Boiling point 212 ºFDensity 7.6 - 7.8 lb/galVapor Density 4.5
Vapor Pressure Not Applicable
Specific Gravity 1 [Ref Std: WATER=1]pH 8.0
Solubility in Water NegligibleVolatile Organic Compounds 83.6 g/l [Test Method: calculated SCAQMD rule 443.1] [Details:
excluding exempt compounds]Percent volatile 72.04 % [Test Method: Estimated]VOC Less H2O & Exempt Solvents 238.45 g/l [Test Method: calculated SCAQMD rule 443.1]Viscosity 10000 - 13000 centipoise
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: None known
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance ConditionFormaldehyde During CombustionCarbon monoxide During Combustion
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 ULTRAFINA(TM) SE PN 06068 06069 06073 06074 06076 03/26/2007
_________________________________________________________________________________________________ Page 6 of 8
Carbon dioxide During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in an industrial or commercial facility in the presence of a combustible material. As a disposal alternative, dispose of waste product in a facility permitted to accept chemical waste.
EPA Hazardous Waste Number (RCRA): Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):60-4300-4993-6, 60-4300-4994-4, 60-4300-5030-6, 60-4300-5035-5, 60-4550-2934-2
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONSContact 3M for more information.
311/312 Hazard Categories:Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - Yes
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 ULTRAFINA(TM) SE PN 06068 06069 06073 06074 06076 03/26/2007
_________________________________________________________________________________________________ Page 7 of 8
STATE REGULATIONSContact 3M for more information.
CALIFORNIA PROPOSITION 65
Ingredient C.A.S. No. ClassificationFORMALDEHYDE 50-00-0 **CarcinogenMINERAL OILS (UNTREATED AND
MILDLY TREATED OILS)NONE **Carcinogen
** WARNING: contains a chemical which can cause cancer.
CHEMICAL INVENTORIESThe components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS), or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.
INTERNATIONAL REGULATIONSContact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard ClassificationHealth: 2 Flammability: 1 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
Revision Changes:Copyright was modified.Section 3: Potential effects from eye contact was modified.Section 3: Potential effects from skin contact information was modified.Section 3: Potential effects from inhalation information was modified.
3M MATERIAL SAFETY DATA SHEET 3M(TM) PERFECT-IT(TM) 3000 ULTRAFINA(TM) SE PN 06068 06069 06073 06074 06076 03/26/2007
_________________________________________________________________________________________________ Page 8 of 8
Section 4: First aid for skin contact - decontamination - was modified.Section 4: First aid for skin contact - medical assistance - was modified.Section 2: Ingredient table was modified.Section 8: Exposure guidelines ingredient information was modified.Section 16: NFPA hazard classification heading was added.Section 16: NFPA hazard classification for health was added.Section 16: NFPA hazard classification for flammability was added.Section 16: NFPA hazard classification for reactivity was added.Section 5: OSHA flammability heading was added.Section 5: OSHA flammability data was added.Section 15: 311/312 hazard categories heading was added.Section 4: First aid for skin contact - termination of exposure - was added.Section 4: First aid for skin contact - handling - was added.Section 16: NFPA explanation was added.Section 15: 311/312 Fire Hazard score was added.Section 15: 311/312 Pressure Hazard score was added.Section 15: 311/312 Reactivity Hazard score was added.Section 15: 311/312 Immediate Hazard score was added.Section 15: 311/312 Delayed Hazard score was added.Section 16: NFPA hazard classification for special hazards was added.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
Transport Information Document
3M ID Number: 60-4550-3178-5
Date: June 17, 2010
Product Description: 3M(TM) Perfect-It(TM) 3000 Paint Finishing Best Practice Kit, 06080, 1 kit per case
Transport Protective Service: MAINTAIN TEMP ABOVE 32F (0C)
NMFC Item: 033440 NMFC Sub: 00 NMFC Class: 055.0
UNITED STATES DEPARTMENT OF TRANSPORTATION - GROUND (U.S. DOT, 49 CFR)
NOT REGULATED
UNITED STATES DEPARTMENT OF TRANSPORTATION - VESSEL (U.S. DOT, 49 CFR)
NOT REGULATED
INTERNATIONAL AIR TRANSPORT ASSOCIATION (IATA)
NOT REGULATED
INTERNATIONAL MARITIME ORGANIZATION (IMO)
NOT REGULATED
Flash Point (Closed-cup): 168°F/75°C
These transportation classifications are provided as a customer service. AS THE SHIPPER YOU REMAIN RESPONSIBLE FOR COMPLYINGWITH ALL THE APPLICABLE LAWS AND REGULATIONS, INCLUDING PROPER TRANSPORTATION CLASSIFICATION AND PACKAGING.3M's transportation classifications are based on product formulations, packaging, 3M policies and 3M's understanding of applicable currentregulations and is valid for the original 3M package only. 3M does not guarantee the accuracy of this classification information. This informationapplies only to transportation classification and NOT THE PACKAGING, LABELING, OR MARKING REQUIREMENTS. The original 3M packageis certified for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory requirements.
The classification is authorized by the Competent Authority of the United States of America and may not meet the requirements of othercompetent authorities.
For Transport Information, please visit 3M.com/Transportinfo
or call 1-800-364-3577 or 651-737-6501 for assistance.