lonworks ciat translator

This document is the property of CIAT and is delivered on the express condition that it is not to be disclosed, reproduced in whole or in part, or used for manufacture by anyone other than CIAT without its written consent, and that no right is granted to disclose or so use any information contained in said document.

CIAT reserves the right to change or modify the information or product described without prior notice and without incurring any liability.

© 2016, CIAT 808-335 Rev. 06/16

LonWorksCIAT Translator

Overview and ConfigurationManual

Introduction ................................................................. 1About this Manual .................................................. 1

Operating Characteristics ........................................... 3Templates ................................................................ 3Default Address and Baud Rate .............................. 5LonWorks CIAT Translator ConfigurationTables ...................................................................... 6

CIAT Translator Configuration Table ........... 6Chiller Mapping Tables .................................. 6Generic Mapping Tables ................................ 6Rooftop Mapping Tables .............................. 7CIAT Translator Device ConfigurationTable ............................................................... 7

CIAT Translator Maintenance Tables ................... 7 Chiller, Rooftop, Generic

Mapping Maintenance Tables ....................... 7Communication Status Maintenance Table .... 7Messages Maintenance Table ....................... 7

Configuration ............................................................... 9Configuration Process ............................................. 9

Select the LonWorks Profile ........................... 9Map CPP Points with LonWorks Variables ..10 Check for Mapping Errors and Confirm Valuesin Maintenance Tables ..................................11Commissioning the Device on the LonWorksNetwork .........................................................12

CIAT Translator Configuration (CONFIG) Table ..13 Chiller Mapping Configuration (CHLRMAP1)Table 1 ....................................................................16Chiller Mapping Configuration (CHLRMAP2)Table 2 ....................................................................21Rooftop Mapping Configuration (RTUMAP1)Table 1 ....................................................................25Rooftop Mapping Configuration (RTUMAP2)Table 2 ....................................................................31

Generic Mapping Configuration (GNRCMAP1)Table 1 ....................................................................36Generic Mapping Configuration (GNRCMAP2)Table 2 ....................................................................40

Maintenance ................................................................45 Chiller Maintenance (CHLRMNT1) Table 1 ....................................45

Chiller Maintenance(CHLRMNT2) Table 2 ....................................48Rooftop Maintenance(RTUMNT1) Table 1 ......................................50Rooftop Maintenance(RTUMNT2) Table 2 ......................................52Generic Maintenance(GNRCMNT1) Table 1 ...................................55Generic Maintenance(GNRCMNT2) Table 2 ...................................57Communication Status (COMMSTAT)Maintenance Table ........................................59Messages Maintenance (MESSAGES)Table ..............................................................61

Appendix ......................................................................63

Index ............................................................................77

iii

ManualRevisions

The LonWorks CIAT Translator Overview and Configuration Manual is catalog number 808-335, Rev. 06/16.

ChangesSection/Chapter

N/A

Introduction

1

This manual contains information about the functions of the LonWorks CIAT Translator module with LON FT-10A (free topology) communi-cation and how the user configures the LonWorks CIAT Translator to perform those functions.

The manual is divided into the following sections:

• Introduction• Operating Characteristics• Configuration• Maintenance

The Introduction consists of this description of the manual.

The Operating Characteristics section contains a description of the CIAT Translator hardware and a summary description of its configura-tion and maintenance tables.

The Configuration section contains detailed lists of the decisions for each CIAT Translator configuration table. Each list entry includes the decision’s purpose, the range of values that may be used, and the default values that will appear in the decision if it is not configured by the user. The mapping tables include an explanation of each decision, along with the LonWorks read/write access, LON Variable Type, and an example CPP point name.

The Maintenance section contains detailed lists of the decisions for each CIAT Translator maintenance table. Each list entry includes the decision’s purpose and the range of values that may be displayed.

The Appendix contains examples of actual configurations for a chiller, rooftop, and generic template, along with a list of LON SNVTs and corresponding CPP (Chiller Proprietary Protocol) point names and descriptions.

About thisManual

Introduction

OperatingCharacteristics

3

The LonWorks CIAT Translator with LON FT-10A (free topology) communication is a micro controller-based module that provides the ability to integrate CIAT CPP-based controllers into LonWorks-based networks.

The LonWorks CIAT Translator (33CNTRANLON) provides CPP to LON FT-10A ANSI/EIA-709.1 protocol conversion.

The CIAT Translator can be mounted in the controls section of any CPP equipment and converts the CPP-based controller data to LonWorks. The CIAT Translator is outdoor duty rated and contains a CPP RS-485 connector and a LON FT-10A communications connector.

The LonWorks CIAT Translator can convert CIAT equipment with CPP controls to LON and outputs the CPP data in standard LON Rooftop or Chiller profiles. CIAT rooftop units can be converted to the standard LonMark Rooftop Unit (RTU) Functional profile 8030 Version 1.1. CIAT chillers can be converted to the standard LonMark Chiller Functional profile 8040 Version 1.0. The chiller and rooftop profiles include additional LON SNVTs beyond those required by the LON standard profiles. These additional SNVTs allow for enhanced LON capability beyond the standard LON-defined profiles. In addition to the rooftop and chiller profiles, a generic LON profile is also supplied. This profile can be used to convert CIAT controllers that may not convert efficiently into the LonMark Rooftop or Chiller profiles.

When connected to a CPP controller, the LonWorks CIAT Translator allows a third party LON device to read and write to the CPP controller’s mapped status display, time schedule, and setpoint schedule data. Note that LON status display write access is subject to the CPP equipment controller’s defined read/write access for each status display item.

The LonWorks CIAT Translator contains chiller, rooftop, and generic LON templates that allow mapping of various CPP points to LON SNVTs. Tables 2-1 through 2-3 show the type and quantity of CPP points in each supplied template.

OperatingCharacteristics

Templates

4

Reads Writes

Space Temperature Space TemperatureOutdoor Air Temperature Outdoor Air TemperatureOutdoor Air Humidity Outdoor Air HumidityCO2 (PPM) Space HumidityCooling Coil % CO2 (PPM)Heating Coil % Supply Air Setpoint (VAV)Economizer Position % Setpoint OffsetFan Speed % 6 Setpoints (degF)Normal/Alarm Discrete 1 Setpoint (PPM)Controlling Setpoint Occupancy Schedule (>64E)4 Generic Temperature 1 Generic Temperature8 Generic Discrete 3 Generic Discrete2 Generic Pressure ("H2O) 3 Generic Discrete3 Generic Percentage 1 Generic Pressure ("H2O)2 Generic Delta Temp 2 Generic Percentage2 Generic (0 to 65535) 1 Generic (0 to 65535)2 Generic (-32767 to 32767)

Reads Writes

Percent Capacity Chiller Start/StopActive Demand Limit Percent Active Demand Limit PercentChilled Water Control Temp Chilled Water Control TempEntering Chilled Water Temp Hot Water Control TempLeaving Chilled Water Temp Occupancy Schedule (>64E)Entering Cond Water Temp 1 Generic TemperatureLeaving Cond Water Temp 2 Generic DiscreteChilled Water Flow Discrete 1 Generic Pressure (PSI)Cond Walter Flow Discrete 1 Generic (0 to 65535)6 Generic Temperature6 Generic Discrete4 Generic Pressure (PSI)2 Generic Percentage2 Generic Delta Temp2 Generic (0 to 65535)2 Generic (-32767 to 32767)

Table 2-1 Rooftop Template

Table 2-2Chiller Template

5

Reads Writes

Cooling Coil % 6 Setpoints (degF)Heating Coil % Occupancy Schedule (>64E)Second Heating Coil % 3 Generic TemperatureEconomizer Position % 3 Generic DiscreteFan Speed % 1 Generic Pressure ("H2O)Normal/Alarm Discrete 1 Generic Pressure (PSI)8 Generic Temperature 2 Generic Percentage8 Generic Discrete 1 Generic PPM2 Generic Pressure ("H2O) 1 Generic (0 to 65535)4 Generic Pressure (PSI)4 Generic Percentage2 Generic Delta Temp1 Generic PPM2 Generic (0 to 65535)2 Generic (-32767 to 32767)

The LonWorks CIAT Translator’s default CPP address is 0,200 (bus number, system element number). The default CPP baud rate is 9600 bps.

Each LonWorks CIAT Translator has a unique LON address. The LON address can be sent to LON configuration tools when the LON service pin is pressed.

The CIAT Translator has three LEDs that are used to indicate opera-tional status:

LED Color Indicates

Status Red Operating, initialization and configurationstatus. The LED blinks at a 2 Hz ratewhen initializing and at 1 Hz whenoperating correctly.

CPP Yellow The CIAT Translator is sending CPP communication messages to the connected CPP controller. If the connected CPP controller is responding, its CPP LED will blink when a message is sent back to the CIAT Translator.

(continued)

Table 2-3Generic Template

Default Addressand Baud Rate

Table 2-4CIAT Translator LEDs

6

LED Color Indicates

LON Green The CIAT Translator is sending LON communication messages to the third party LonWorks network.

The CIAT Translator contains the configuration tables listed below. For descriptions of the decisions in each table, refer to the Configuration section of this manual. The purpose of each table is summarized on the following pages.

CIAT Translator Device Configuration Table (CtlrID) Chiller Mapping Table 1 (CHLRMAP1)Chiller Mapping Table 2 (CHLRMAP2)CIAT Translator Configuration Table (CONFIG) Generic Mapping Tab le 1 (GNRCMAP1)Generic Mapping Table 2 (GNRCMAP2)Rooftop Unit Mapping Table 1 (RTUMAP1) Rooftop Unit Mapping Table 2 (RTUMAP2)

The CIAT Translator Configuration Table (CONFIG) contains deci-sions used to specify the following:

• LonWorks Profile (Rooftop, Chiller, Generic)• CPP Address• Auto-mapping• Reset Points Profile

The Chiller Mapping Tables (CHLRMAP1 and CHLRMAP2) are used to map or associate CPP points with the variables in the LonWorks Chiller profile, which is based on LonMark Functional Profile Chiller 8040 V 1.0. These tables are configured if the CIAT Translator CONFIG Table's Device Type decision is set to 2 (Chiller).

The CIAT Translator's Generic Mapping Tables (GNRCMAP1 and GNRCMAP2) are used to map or associate CPP points with the variables in the LonWorks generic controller profile. These tables are configured if the CIAT Translator CONFIG Table's Device Type decision is set to 3 (Generic). This table could be used, for example, to allow LON access to an air handler.

Table 2-4CIAT Translator LEDs (continued)

LonWorks CIAT Translator Configuration Tables

CIAT Translator Configuration Table

Chiller Mapping Tables

Generic MappingTables

7

Chiller, Rooftop,Generic MappingMaintenance Tables

The CIAT Translator's Rooftop Mapping Tables (RTUMAP1 and RTUMAP2) are used to map or associate CPP points with the variables in the LonWorks rooftop profile, which is based on LonMark Function Profile Rooftop Unit 8030 Version 1.1. The table is configured if the CIAT Translator CONFIG Table's Device Type decision is set to 1(Rooftop).

The CIAT Translator contains a Device Configuration Table (CtlrID). By changing the information that appears in this table, you can change the name, description, and location that appears for the CIAT Translator in the CPP front end's Controller List.

The CIAT Translator contains the following maintenance tables:

Chiller Mapping Table 1 (CHLRMNT1)Chiller Mapping Table 2 (CHLRMNT2)Communication Status Table (COMSTAT)Generic Mapping Table 1 (GNRCMNT1)Generic Mapping Table 2 (GNRCMNT2)LonWorks Messages Table (MESSAGES)Rooftop Unit Mapping Table 1 (RTUMNT1)Rooftop Unit Mapping Table 2 (RTUMNT2)

The maintenance values displayed in these tables are read-only values that show the current value of the CPP points that have been mapped to the Lonworks variables as the points exist in the CPP system element. These values are updated every 30 seconds. Note that if a LonWorks read (nvo) and write (nvi) variable have been mapped to the same CPP point, they will display the same value in the maintenance table display.

The maintenance values displayed in this table are read-only values that show diagnostic data about LonWorks-to-CPP system element com-munication.

The maintenance values displayed in this table are read-only values that show diagnostic data about LonWorks-to-CPP system element com-munication messages.

Rooftop MappingTables

CIAT Translator Device Configuration Table

CIAT Translator Maintenance Tables

Messages MaintenanceTable

Communication StatusMaintenance Table

Configuration

9

The LonWorks CIAT Translator's operation is controlled by decisions entered in a group of configuration tables. The CIAT Translator contains the following configuration tables:

CTLR_ID

CHLRMAP1CHLRMAP2CONFIGGNRCMAP1GNRCMAP2RTUMAP1RTUMAP2

CIAT Translator Controller Identification TableChiller Mapping Configuration Table 1 Chiller Mapping Configuration Table 2 CIAT Translator Configuration Table Generic Configuration Table 1Generic Configuration Table 2Rooftop Unit Configuration Table 1 Rooftop Unit Configuration Table 2

LonWorks CIAT Translator configuration and start-up consists of four main processes:

1. Physically connect the LonWorks CIAT Translator to the CPPsystem element.

2. Select the appropriate LonWorks profile. You do this in theCONFIG Table.

3. Map, or associate, CPP points with LonWorks points by config-uring the appropriate set of configuration tables (rooftop, chiller,or generic), depending on the device type that you selected in theCONFIG Table.

4. Commission the CIAT Translator on the LonWorks network.

Each of the above-listed processes is discussed below.

1. Connect the target CPP system element to the CIAT Translator's CPP connector. Confirm that the element is powered and communicating on the CPP Bus.

2. Using a CPP front end (such as Service Tool) access the CIAT Translator’s CONFIG Table and select the appropriate LonWorks profile (Rooftop, Chiller, or Generic) by entering a 1, 2, or a 3 into the CONFIG Table's Device Type decision.

Configuration

ConfigurationProcess

Select the LonWorksProfile

10

3. Enter appropriate values into all CONFIG Table decisions and download the CONFIG Table into the CIAT Translator.

If the CIAT Translator is on a CPP bus with elements other than the single CPP device with which it is communicating, you must:

• Set Bus and Element #s• Set the Reset Points Profile decision to Yes• Download.

This chapter's CIAT Translator Configuration (CONFIG) Tablesection contains explanations of and allowable entries and defaultvalues for each CONFIG Table decision.

After approximately 5 seconds, the CIAT Translator should identify the target CPP system element and begin to download its tables. This takes 10 to 40 seconds, depending on the number of tables in the target CPP system element. During this period, the Yellow LED will flash to indicate CPP bus activity. When the flashing stops, the download is complete.

Note: Do not cycle CIAT Translator power within 30 secondsof downloading the CONFIG Table or any of the map-ping tables. Be sure that the Yellow CPP LED is NOT flashing.

1. Using a CPP front end, access the appropriate set of configurationtables, depending on the value you specified in the CONFIG Table'sDevice Type decision :

Rooftop (Device Type 1) - RTUMAP1 and RTUMAP2Chiller (Device Type 2) - CHLRMAP1 and CHLRMAP2Generic (Device Type 3) - GNRCMAP1 and GNRCMAP2

2. You will now "map" or associate CPP point names with each LonWorks network variable name that is listed in the configuration tables. Note that those LonWorks network variables having read access begin with the characters nvo and LonWorks network variables with write access begin with the characters nvi.

Entries are case insensitive - upper or lower case characters may beused.

Map CPP Points with LonWorks Variables

11

In the Lon structure, there are different types of points for reading and writing purposes. If a CPP point is to be both read and written to by the Lon system, it is recommended that you use two Lon points to accomplish this. The reason for using a separate Lon point to read the CPP point is in case that CPP point is forced by a higher level function than the CIAT Translator itself, which uses Control forces.

Also in the Lon structure, there are dedicated types of points for different types of generic values, such as Temperature, Tempera-ture Difference, Pressure, Percent, and Discrete. You must associate a particular CPP point with the matching Lon point type or the CIAT Translator will not function properly.

In addition, for the CIAT Translator's chiller and rooftop map-ping tables, the identity of some Lon points have been pre-determined to conform to the LonMark functional profile for the particular device type. Using these points, where possible, allows the generic point types that appear later in the mapping table to be used for other CPP points. Example: In the Chiller tables there are dedicated Lon points for Entering and Leaving Chilled Water Temperature, and in the Rooftop tables there are dedicated points for Space and Outside Air Temperature.

Explanations of each table decision, along with example CPP point names, can be found later in this Configuration chapter. Examples of completed templates and lists of SNVTs and corresponding CPP points can be found in the Appendix.

1. Using a CPP front end, access the two configuration mappingtables (chiller, rooftop, or generic) that were used in Step 2 of theMap CPP Points with LonWorks Variables procedure, whichappears prior to this section of the Configuration chapter.

2. Download each table to the CIAT Translator and wait approxi-mately one minute.

During this time the CIAT Translator performs error checking toverify if you have entered any non-existent point names as well aschecks for correct point types (analog/discrete,etc.).

3. Upload the tables and check the displayed tables.

Look for any decisions that may have the message error**1 orerror**2 displayed in their Value column. These messagesindicate that the entry that was made for this decision is invalid:

Check for MappingErrors and ConfirmValues in MaintenanceTables

12

error**1 Indicates that the point name was not found in thetarget CPP system element.

error**2 The point name was found on the target CPP devicebut the data type is not valid to this LonWorks net-work variable.

The errors should be corrected and the tables downloaded.

Example: If, in the CHILLERMAP1 Table, the nvoTEMP1decision has been configured with the point nameDP_A, which is a pressure, the message error**2 willbe displayed because this decision requires a tempera-ture point.

After verifying that there are no error messages in either Configuration mapping Table, cycle power to the CIAT Translator and observe the yellow LED. This is the CPP communication indicator.

Approximately one minute after the yellow LED stops blinking, check theappropriate Maintenance Tables to confirm that the correct data isdisplayed for each configured point.

Note: The CIAT Translator polls the CPP system element every 30 seconds to both Read and Write CPP points.

The CIAT Translator is now fully commissioned on the CIAT/CPP side and is ready for the Lon systems integrator to commission the Lon side using a Lon software tool such as LonMaker.

A list of the actual CPP points configured in the appropriate MAP1 and MAP2 templates should be supplied to the systems integrator to assist him/her with the commissioning process. A blank copy of these templates can be found in the Appendix of this manual. Additionally, the NeuronID of the Echelon Lon processor chip should also be supplied to the systems integrator. This is a 12 character alphanumeric code that can be found on a white label located along the upper edge of the control board, opposite the Lon connector.

After the LonWorks CIAT Translator is added to the LonWorks network, the LonWorks network variables that were mapped in this chapter's Map CPP Points with LonWorks Variables procedure can be used to read/write data points on the target CPP system element.

Commissioning theDevice on theLonWorks Network

13

CIAT Translator Configuration(CONFIG) Table

The CIAT Translator's CONFIG Table is shown below. An explanation of each decision, including allowable entries and default values follows.

Note: When starting up the CIAT Translator this is the first tableyou must configure.

Device Type1=Rftp, 2=Chillr,3=Gnrc

Use this decision to select the desired LonWorks Profile. After entering this value and downloading this table to the CIAT Translator, the appropriate LonWorks variable names will be loaded into the CIAT Translator.

Allowable Entries 1 = Rooftop2 = Chiller3 = Generic

Default Value 0

Figure 3-1CIAT Translator Configuration (CONFIG) Table

14

Use this decision to specify the bus number of the CPP system element to which the CIAT Translator is connected.

Note: If you do not enter a value for this decision or if the value isincorrect, the CIAT Translator will attempt to find the element address itself. You will then have to upload this table to check if the correct address has been found.

Allowable Entries 0-239

Default Value 0

Use this decision to specify the number of the CPP system element to which the CIAT Translator is connected.

Note: If you do not enter a value for this decision or if the value is incorrect, the CIAT Translator will attempt to find the element address itself. You will then have to upload this table to check if the correct address has been found.

Allowable Entries 0-239

Default Value 0

Use this decision to disable or enable the CIAT Translator's automatic mapping feature. Setting this decision to No will cause the CIAT Trans-lator to upload mapping tables that may exist in the target CPP system element. Setting this decision to Yes will disable automatic mapping and will cause the CIAT Translator to use the mapping tables from the CIAT Translator.

Note: No current CPP system element contains automatic mappingtables.

Allowable Entries 0 = No1 = Yes

Default Value 0

Target Bus No.

Target Address

Disable Auto-mapping

15

Reset Points Profile Use this decision to clear the contents of all of the CIAT Translator's CPP points to LonWorks variable mapping tables. This decision resets to No on completion of the operation. The following tables will be cleared:

RTUMAP1 and RTUMAP2CHLRMAP1 and CHLRMAP2GNRCMAP1 and GNRCMAP2

Note: Do not save this decision set to Yes. Do not cycle CIAT Translator power for at least 30 seconds after downloading this decision set to Yes. If you do cycle power within 30 seconds of downloading this decision as Yes, the CIAT Translator will return to its default address of 0,200 at a baud rate of 9600 baud.


Default Value 0

Use this decision to clear the COMMSTAT Maintenance Table's NumSuccessful Messages and Num Failed Messages counters. This decisionresets to No on completion of the operation.

Note: Do not save this decision set to Yes.


Default Value 0

Use this decision to specify whether the CIAT Translator should act as a CPP alarm acknowledger for all alarm messages received from the CPP Bus. There must be only one CPP alarm acknowledger per CPP.

Note that alarms from the CIAT Translator's target system element are placed into the CIAT Translator's buffer.


Default Value 1

Reset Comm. Counters

Alarm Acknowledger

16

Chiller MappingConfiguration(CHLRMAP1)Table 1

The CIAT Translator's CHLRMAP1 Table is used to map or associate CPP points with the variables in the LonWorks chiller profile (which is based on LonMark Functional Profile: Chiller 8040 V 1.0). This table should be configured if the CIAT Translator CONFIG Table's Device Type decision was set to 2 (Chiller). A sample CHLRMAP1 Table is shown below. An explanation of each decision, including LonWorks read/write access, LON Variable Type, along with an example CPP point name follows.

CPP point names can consist of up to 8 characters. The default for each decision is blank.

Figure 3-2Chiller Mapping 1Configuration (CHLRMAP1)Table

Allowable Entries andDefault Value

17

Use this decision to specify the name of the discrete CPP point that the LON system can write to in order to start or stop the chiller.

LON Variable Type SNVT_switch

Read/Write Access Write

Example CHIL_S_SChiller Start/Stop

Use this decision to specify the name of the analog CPP point that the LON system can write to in order to set the leaving chilled water tem-perature setpoint when the chiller is operating in cooling mode.

LON Variable Type SNVT_temp_p


Example CTRL_PNTControl Point

Use this decision to specify the name of the discrete CPP point that the LON system can read in order to indicate the chiller's current status (on/off ).

Note: Most CPP chillers do not contain this point.


Read/Write Access Read

Use this decision to specify the name of the analog CPP point that the LON system can read in order to obtain the current value of the chiller's cooling or heating setpoint. The setpoint to be used (cooling or heating) depends on the chiller's current operating mode.




Use this decision to specify the name of the analog CPP point that the LON system can write to in order to set the capacity limit of the chiller.

LON Variable Type SNVT_lev_percent


Example DEM_LIMActive Demand Limit

nviCoolSetpt

nvoOnOff

nvoActiveSetpt

nviCapacityLim

nviChillerEnable

18

Use this decision to specify the name of the analog CPP point that the LON system can write to in order to set the heating setpoint.




Use this decision to specify the name of the analog CPP point that the LON system can read in order to obtain the current running capacity of the chiller.



Example CAP_TPercent Total Capacity

Use this decision to specify the name of the analog CPP point that the LON system can read in order to obtain the chiller's current capacity limit setpoint.



Example DEM_LIMActive Demand Limit

Use this decision to specify the name of the analog CPP point that the LON system can read in order to obtain the leaving chilled water tem-perature.



Example LWTLeaving Fluid Temp

Use this decision to specify the name of the analog CPP point that the LON system can read in order to obtain the entering chilled water temperature.



Example EWTEntering Fluid Temp

nviHeatSetpt

nvoActualCapacity

nvoCapacityLim

nvoEntCHWTemp

nvoLvgCHWTemp

19

nvoLvgCNDWTemp

Use this decision to specify the name of the analog CPP point that the LON system can read in order to obtain the entering condenser water temperature.



Example COND_EWTCondenser Entering Fluid

Use this decision to specify the name of the analog CPP point that the LON system can read in order to obtain the leaving condenser water temperature.



Example COND_LWTCondenser Leaving Fluid

Use this decision to provide the name of the discrete CPP point that the LON system can read in order to obtain the main running mode of the chiller.


LON Variable Type SNVT_chlr_status


Use this decision to provide the name of the discrete CPP point that the LON system can read in order to obtain the main operating status of the chiller.




Use this decision to provide the name of the discrete CPP point the LON system can read in order to obtain the alarm status of the chiller.




nvoChillerStat.run_mode

nvoEntCNDWTemp

nvoChillerStat.in_alarm

nvoChillerStat.op_mode

20

Use this decision to specify the name of the discrete CPP point that the LON system can read in order to obtain the status of the chiller (start/stop).



Example CHIL_S_SChiller Start/Stop

Use this decision to specify the name of the discrete CPP point that the LON system can read in order to obtain the chiller's local or network control status.




Use this decision to specify the name of the discrete CPP point that the LON system can read in order to indicate that the chiller cannot reach setpoint.




Use this decision to specify the name of the discrete CPP point that the LON system can read in order to indicate if chilled water flow is present.



Example COOLFLOWCooler Flow Switch

Use this decision to specify the name of the discrete CPP point that the LON system can read in order to indicate if condenser water flow is present.



Example CONDFLOWCondenser Flow Switch

nvoChillerStat.run_enabl

nvoChillerStat.Local

nvoChillerStat.Limited

nvoChillerStat.cndw_flow

nvoChillerStat.chw_flow

21

nviOccSchedule Use this decision to specify the name of the CPP occupancy schedule that the LON system can write to in order to set occupancy times.

Note: The chiller unit must be configured to use a global occupancyschedule (Allowable entries: OCCPC65E to OCCPC99E).Refer to the chiller documentation for additional information onthe setup of the global occupancy schedule.

LON Variable Type SNVT_tod_event


Example OCCPC66EOccupancy Equipment

The CIAT Translator's CHLRMAP2 Table is used to map or associate CPP points with the variables in the LonWorks chiller profile. This table, in addition to the CHLRMAP1 Table, should be configured if the CIAT Translator CONFIG Table's Device Type decision was set to 2 (Chiller). A sample CHLRMAP2 Table is shown below. An explanation of each decision, including LonWorks read/write access, LON Variable Type, along with an example CPP point name follows.


Use this decision to specify the name of the analog CPP point that the LON system can write to in order to set an additional chiller operating temperature.



Example OATOutdoor Air Temperature

Use these 6 decisions to specify the names of the analog CPP points that the LON system can read in order to obtain additional chiller operating temperatures.



Example TMP_SCTASaturated Condensing Temp

Chiller MappingConfiguration(CHLRMAP2)Table 2


nviTEMP1

nvoTEMP1 - 6

22

Figure 3-3Chiller Mapping 2Configuration (CHLRMAP2)Table

23

Use this decision to specify the name of the analog CPP point that the LON system can write to in order to set an additional chiller operating pressure.

Note: 1. Most CPP chillers do not allow write access to this point.2. For use with points having units of psi (kPa).

LON Variable Type SNVT_press


Use these 4 decisions to specify the names of the analog CPP points that the LON system can read in order to obtain additional chiller operating pressures.

Note: 1. For use with points having units of psi (kPa).

LON Variable Type SNVT_press


Example SP_ASuction Pressure Circuit A

Use these 2 decisions to specify the names of the analog CPP points the LON system can read in order to obtain additional chiller operating parameters in percentage.



Example CAPA_APercentage Operating Capacity

Use these 2 decisions to specify the names of the analog CPP points that the LON system can read in order to obtain additional chiller differential temperatures.

LON Variable Type SNVT_temp_diff


Example SH_ASuction Superheat

Use these 2 decisions to specify the names of the discrete CPP points that the LON system can write to in order to set additional discrete operating parameters.



Example EMSTOPEmergency Stop

nvoPRESS1 - 4

nviPRESS1

nvoPCT1 - 2

nvoTEMPDIFF1 - 2

nviDISCRETE1 - 2

24

Use these 6 decisions to specify the names of the discrete CPP points that the LON system can read in order to obtain additional discrete operating parameters.



Example FANS_1Fan 1 Relay

Use this decision to specify the name of the analog or multi-state CPP point that the LON system will write to in order to set additional analog or multi-state operating parameters.

LON Variable Type SNVT_count


Example S_HRSService Ontime Hours

Use these decisions to specify the names of the analog or multi-state CPP points that the LON system will read in order to obtain additional analog or multi-state values.



Example STATRun Status

Use these decisions to specify the names of the analog or multi-state CPP points that the LON system will read in order to obtain additional analog or multi-state values.

LON Variable Type SNVT_count_inc


Example STATRun Status

nvoDISCRETE1 - 6

nviCOUNT1

nvoCOUNT1 - 2

nvoCOUNTinc1 - 2

25

The CIAT Translator's RTUMAP1 Table is used to map or associate CPP points with the variables in the LonWorks rooftop profile (which is based on LonMark Functional Profile: Rooftop Unit (RTU) 8030 Version 1.1). This table should be configured if the CIAT Translator CONFIG Table's Device Type decision was set to 1 (Rooftop). A sample RTUMAP1 Table is shown on the page which follows. An explanation of each decision, including LonWorks read/write access, LON Variable Type, along with an example CPP point name follows.


Use this decision to specify the name of the analog CPP point that the LON system can write to in order to set the space temperature.



Example SPTSpace Temperature

Use this decision to specify the name of the analog CPP point that the LON system can write to in order to set the temperature setpoint.




Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the space temperature.



Example SPTSpace Temperature

Use this decision to specify the name of the discrete CPP point that the LON system can read in order to indicate the rooftop's operating mode.

Note: CPP rooftops do not contain this point.

LON Variable Type SNVT_hvac_status


nviSpaceTemp

nvoUnitStatus.mode

nvoSpaceTemp

nviSetPoint


Rooftop MappingConfiguration(RTUMAP1)Table 1

26

Figure 3-4Rooftop Mapping 1Configuration (RTUMAP1)Table

27

Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the current primary heat capacity in percent full scale.



Example HCAPHeating % Total Capacity

Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the current secondary heat capacity in percent full scale.



Example HCAPHeating % Total Capacity

Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the current secondary cooling capacity in percent full scale.



Example CCAPCooling % Total Capacity

Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the current economizer position in percent full scale.



Example ECONOPOSEconomizer Position %

Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the current fan speed in percent full scale.



Example VFDVariable Frequency Drive Speed %

nvoUnitStatus.heat_out_s

nvoUnitStatus.cool_out

nvoUnitStatus.econ_out

nvoUnitStatus.fan_out

nvoUnitStatus.heat_out_p

28

nvoUnitStatus.in_alarm Use this decision to provide the name of the discrete CPP point that theLON system can read in order to indicate the alarm status of the rooftop.

Note: Most CPP rooftops do not contain this point.



Use this decision to specify the name of the CPP occupancy schedule that the LON system can write to in order to set occupancy times.

Note: The rooftop unit must be configured to use a global occupancyschedule (Allowable entries: OCCPC65E to OCCPC99E).Refer to the rooftop documentation for additional informationon the setup of the global occupancy schedule.




Use this decision to specify the name of the analog CPP point that the LON system will write to in order to set the active temperature setpoint.




Use this decision to specify the name of the analog CPP point that the LON system will write to in order to set the outside air temperature.



Example OATOutside Air Temperature

Use this decision to specify the name of the analog CPP point that the LON system will write to in order to set the outside air relative humidity.



Example OARHOutside Air Relative Humidity

nviOccSchedule

nviSetptOffset

nviOutsideRH

nviOutsideTemp

29

Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the temperature setpoint.




Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the outside air temperature.



Example OATOutside Air Temperature

Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the outside air relative humidity.



Example OARHOutside Air Relative Humidity

Use this decision to specify the name of the analog CPP point that the LON system will write to in order to set the relative humidity.



Example RHRelative Humidity

Use this decision to specify the name of the analog CPP point that the LON system will write to in order to set the CO2 level in ppm.

LON Variable Type SNVT_ppm


Example IAQIndoor air quality

nvoEffectSetpt

nvoOutsideTemp

nvoOutsideRH

nviSpaceRH

nviCO2

30

Use this decision to specify the name of the analog CPP point that the LON system will read to indicate the CO2 level in ppm.



Example IAQIndoor air quality

Use this decision to specify the name of the analog CPP point that the LON system will write to in order to set an additional rooftop operating temperature.




Use these 4 decisions to specify the analog CPP point names that the LON system will read to indicate additional rooftop operating temperatures.



Example TMP_SCTASaturated Condensing Temp

Use this decision to specify the name of the analog CPP point that the LON system will write to in order to set an additional rooftop operating pressure.

Note: For use with points having units of "H2O (Pa).

LON Variable Type SNVT_press_p


Example SPStatic Pressure

nvoCO2

nviTEMP1

nvoTEMP1-4

nviPRESS1

31

Use these 2 decisions to specify the names of the analog CPP point that the LON system will read to indicate additional rooftop operating pres-sures.

Note: For use with points having units of "H2O (Pa).

LON Variable Type SNVT_press_p



The CIAT Translator's RTUMAP2 Table is used to map or associateCPP points with the variables in the LonWorks rooftop profile. This table should be configured if the CIAT Translator CONFIG Table's Device Type decision was set to 1 (Rooftop). A sample RTUMAP2Table is shown on the page which follows. An explanation of each decision, including LonWorks read/write access, LON Variable Type, along with an example CPP point name follows.


Use these 2 decisions to specify the names of the analog CPP points that the LON system will write to in order to set additional rooftop operating parameters in percentage.



Example ECONPOSEconomizer Position

Use these 3 decisions to specify the names of the analog CPP point that the LON system will read to indicate additional rooftop operating parameters in percentage.



Example CAPA_APercentage Operating Capacity


Rooftop MappingConfiguration(RTUMAP2)Table 2

nvoPRESS1 - 2

nvoPCT1-3

nviPCT1-2

32

Figure 3-5Rooftop Mapping 2Configuration (RTUMAP2)Table

33

Use these 2 decisions to specify the names of the analog CPP points that the LON system will read to indicate additional rooftop differential temperatures.



Example SH_ASuction Superheat

Use these 3 decisions to specify the names of the discrete CPP points that the LON system will write to in order to set additional discrete operating parameters.



Example EMSTOPEmergency Stop

Use these 8 decisions to specify the names of the discrete CPP points that the LON system will read to indicate additional discrete operating parameters.




Use this decision to provide the name of the analog CPP point that the LON system will write to in order to set the CO2 threshold value.



Example IAQSIndoor Air Quality Setpoint

Use this decision to provide the name of the analog CPP point that the LON system will write to in order to set the occupied cooling setpoint.

LON Variable Type SNVT_temp_setpt


Example OCSPOccupied Cool Setpoint

nviDISCRETE1 - 3

nvoDISCRETE1 - 8

nciCO2Limit

nciSetpnts.occupied_cool

nvoTEMPDIFF1 - 2

34

nciSetpnts.occupied_heat

nciSetpnts.standby_heat

nciSetpnts.unocc_heat

nciSetpnts.unocc_cool

Use this decision to provide the name of the analog CPP point that the LON system will write to in order to set the cooling setpoint in standby mode.

Note: Most CPP rooftops do not use this mode.



Use this decision to provide the name of the analog CPP point that the LON system will write to in order to set the unoccupied cooling setpoint.



Example UCSPUnoccupied Cool Setpoint

Use this decision to provide the name of the analog CPP point that the LON system will write to in order to set the occupied heating setpoint.



Example OHSPOccupied Heat Setpoint

Use this decision to provide the name of the analog CPP point that the LON system will write to in order to set the heating setpoint in standby mode.




Use this decision to provide the name of the analog CPP point that the LON system will write to in order to set the unoccupied heating setpoint.



Example UHSPUnoccupied Heat Setpoint

nciSetpnts.standby_cool

35




Example OASPOA cfm Setpoint

Use these 2 decisions to specify the names of the analog or multi-state CPP points that the LON system will read in order to obtain additional analog or multi-state values.



Example OACFMOA Airflow





nviCOUNT1

nvoCOUNT1 - 2

nvoCOUNTinc1 - 2

36

The CIAT Translator's GNRCMAP1 Table is used to map or associate CPP points with the variables in the LonWorks generic controller profile. This table should be configured if the CIAT Translator CONFIG Table's Device Type decision was set to 3 (Generic). This table could be used, for example, to allow LON access to an air handler. A sample GNRCMAP1 Table is shown on the page which follows. An explanation of each decision, including LonWorks read/write access, LON Variable Type, along with an example CPP point name follows. The decision explanations and example point names below are taken from a CPP air handler. Keep in mind, however, that the generic controller profile can also be used with other types of CPP controllers.


Use this decision to specify the name of the discrete CPP point that the LON system can read in order to indicate the air handler's operating mode.

Note: Most CPP air handlers do not contain this point.



Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the current primary heat capacity in percent full scale.



Example HCVHeating Coil Valve %

Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the current secondary heat capacity in percent full scale.



Example HCVHeating Coil Valve %


Generic MappingConfiguration(GNRCMAP1)Table 1

nvoUnitStatus.mode



37

Figure 3-6Generic Mapping 1Configuration (GNRCMAP1)Table

38

Use this decision to specify the name of the analog CPP point that that the LON system can read in order to indicate the current cooling capacity in percent full scale.



Example CCVCooling Coil Valve

Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the current economizer posi-tion in percent full scale.



Use this decision to specify the name of the analog CPP point that the LON system can read in order to indicate the current fan speed in percent full scale.



Example VFDVariable Frequency Drive Speed %

Use this decision to provide the name of the discrete CPP point that the LON system can read in order to indicate the alarm status of the air handler.







nvoUnitStatus.in_alarm

39

Use this decision to specify the name of the CPP occupancy schedule that the LON system can write to in order to set occupancy times.

Note: The CPP unit must be configured to use a global occupancyschedule (Allowable entries: OCCPC65E to OCCPC99E). Refer to the CPP documentation for additional information on the setup of the global occupancy schedule.




Use these 3 decisions to specify the name of the analog CPP point that the LON system can write to in order to set an additional air handler operating temperature.




Use these 8 decisions to specify the analog CPP point names that the LON system can read in order to indicate additional air handler operating temperatures.



Example SATSupply Air Temperature

Use these 2 decisions to specify the name of the analog CPP point that the LON system can write to in order to set an additional air handler operating pressure.

Note: 1. Most CPP air handlers do not allow write access to thispoint.

2. PRESS1 is for use with points having units of "H20 (Pa).3. PRESS2 is for use with points having uints of psi (kPa).

LON Variable Type PRESS1: SNVT_press_pPRESS2: SNVT_press


nviOccSchedule

nviTEMP1 - 3

nvoTEMP1 - 8

nviPRESS1 - 2

40

Use these 6 decisions to specify the names of the analog CPP point that that the LON system can read in order to indicate additional air handler operating pressures.

Note: 1. PRESS1-2 are for use with points having units of "H20 (Pa).2. PRESS3-6 are for use with points having units of psi (kPa).

LON Variable Type PRESS1-2: SNVT_press_pPRESS3-6: SNVT_press



Use these 2 decisions to specify the names of the analog CPP points that the LON system can read in order to indicate additional air handler differential temperatures.

Note: Most CPP air handlers do no contain these points.



The CIAT Translator's GNRCMAP2 Table is used to map or associate CPP points with the variables in the LonWorks generic profile. This table, in addition to the GNRCMAP1 Table, should be configured if the CIAT Translator CONFIG Table's Device Type decision was set to 3 (Generic). A sample GNRCMAP2 Table is shown below. An explana-tion of each decision, including LonWorks read/write access, LON Variable Type, along with an example CPP point name follows. The decision explanations and example point names below are taken from a CPP air handler. Keep in mind, however, that the generic controller profile can also be used with other types of CPP controllers.


Use these 2 decisions to specify the names of the analog CPP points that the LON system will write to in order to set additional operating parameters in percentage.



Example MIXDMixed Air Damper

nvoTEMPDIFF1 - 2

Generic MappingConfiguration(GNRCMAP2)Table 2

nviPCT1 - 2

nvoPRESS1 - 6

41

Figure 3-7Generic Mapping 2Configuration (GNRCMAP2)Table

42

Use these 4 decisions to specify the names of the analog CPP points that the LON system can read in order to indicate additional air handler operating parameters in percentage.



Example RFVCReturn Fan Volume Control

Use these 3 decisions to specify the names of the discrete CPP points that the LON system can write to in order to set additional discrete operating parameters.



Example FLTSFilter Status

Use these 8 decisions to specify the names of the discrete CPP points that the LON system can read in order to indicate additional discrete operating parameters.




Use this decision to provide the name of the analog CPP point that the LON system can write to in order to set the occupied cooling setpoint.



Example OCSPOccupied Cool Setpoint

Use this decision to provide the name of the analog CPP point that the LON system can write to in order to set the cooling setpoint in standby mode.

Note: Most CPP air handlers do not use this mode.



nvoDISCRETE1 - 8



nviDISCRETE1 - 3

nvoPCT1 - 4

43

Use this decision to provide the name of the analog CPP point that the LON system can write to in order to set the unoccupied cooling setpoint.



Example UCSPUnoccupied Cool Setpoint

Use this decision to provide the name of the analog CPP point that the LON system can write to in order to set the occupied heating setpoint.



Example OHSPOccupied Heat Setpoint

Use this decision to provide the name of the analog CPP point that the LON system can write to in order to set the heating setpoint in standby mode.

Most CPP air handlers do not contain this point.



Use this decision to specify the name of the analog CPP point that the LON system will write to in order to set an additional operating param-eter in PPM.



Example AQ1Air Quality 1 (ppm)

Use this decision to specify the name of the analog CPP point that the LON system will read in order to obtain an additional analog values in PPM.



Example AQ1Air Quality 1 (ppm)



nviPPM1

nvoPPM1


44




Example OASPOA cfm Setpoint









nvoCOUNT1 - 2

nvoCOUNTinc1 - 2

nviCOUNT1

Maintenance

45

The CIAT Translator contains the maintenance tables listed below.

CHLRMNT1 Chiller Maintenance Table 1CHLRMNT2 Chiller Maintenance Table 2COMMSTAT Communication Status Maintenance TableGNRCMNT1 Generic Maintenance Table 1GNRCMNT2 Generic Maintnenance Table 2MESSAGES Messages Maintenance TableRTUMNT1 Rooftop Maintenance Table 1RTUMNT2 Rooftop Mainten ance Table 2

The maintenance values displayed in these tables are read-only values that show the current value of the CPP points that have been mapped to the Lonworks variables as the points exist in the CPP system element. These values are updated every 30 seconds. Note that if a LonWorks read (nvo) and write (nvi) variable have been mapped to the same CPP point, they will display the same value in the maintenance table display.

Figure 4-1 on the page which follows illustrates the Chiller Maintenance(CHLRMNT1) Table. An explanation of each value in the table follows.Note that the valid display ranges are dependent on the point.

Indicates the commanded state of the chiller (on or off).

Indicates the commanded value for the leaving chilled water temperaturesetpoint when the chiller is operating in cooling mode.

Indicates the chiller's current status (on/off ).


Indicates the current value of the chiller's cooling or heating setpoint. Thesetpoint to be displayed (cooling or heating) depends on the chiller'scurrent operating mode.

Indicates the commanded value for the capacity limit of the chiller.

nviChillerEnable

ChillerMaintenance(CHLRMNT1)Table 1

nviCoolSetpt

nvoOnOff

nvoActiveSetpt

Maintenance

nviCapacityLim

46

Figure 4-1Chiller Maintenance(CHLRMNT1)Table 1

47

Indicates the commanded heating setpoint.

Indicates the current running capacity of the chiller.

Indicates the chiller's current capacity limit setpoint.

Indicates the leaving chilled water temperature.

Indicates the entering chilled water temperature.

Indicates the entering condenser water temperature.

Indicates the leaving condenser water temperature.

Indicates the main running mode of the chiller.


Indicates the main operating status of the chiller.


Indicates the alarm status of the chiller.


Indicates the start or stop status of the chiller.

Indicates the chiller's local or network control status.


Indicates if the chiller cannot reach setpoint.


Indicates the presence of chilled water flow.

Indicates the presence of condenser water flow.

Indicates the next commanded occupancy state, as determined by the CPP global occupancy equipment table.

nviHeatSetpt

nvoActualCapacity

nvoCapacityLim

nvoLvgCNDWTemp

nvoEntCNDWTemp

nvoEntCHWTemp

nvoLvgCHWTemp

nvoChillerStat.run_mode

nvoChillerStat.op_mode

nvoChillerStat.in_alarm

nvoChillerStat.run_enabl

nvoChillerStat.Local

nvoChillerStat.Limited

nvoChillerStat.cndw_flow

nvoChillerStat.chw_flow

nviOccSchedule

48

Figure 4-2 shown below illustrates the Chiller Maintenance(CHLRMNT2) Table. An explanation of each value in the table follows.Note that the valid display ranges are dependent on the point.

Chiller Maintenance(CHLMNT2) Table 2

Figure 4-2Chiller Maintenance(CHLRMNT2)Table 2

49

nviTEMP1

nvoPRESS1 - 4

nvoTEMP1 - 6

nviPRESS1

Indicates an additional chiller commanded operating temperature.

Indicates additional chiller operating temperatures.

Indicates an additional chiller commanded operating pressure.

Indicates additional chiller operating pressures.

Indicates additional chiller operating parameters in percentage.

Indicates additional chiller differential temperatures.

Indicates additional commanded discrete operating parameters.

Indicates additional discrete operating parameters.

Indicates chiller commanded analog or multi-state parameter.

Note: This point will always display in customary US units.

Indicate chiller analog or multi-state values.

Note: These points will always display in customary US units.

Indicate chiller analog or multi-state values.


nvoPCT1 - 2

nvoTEMPDIFF1 - 2

nviDISCRETE1 - 2

nvoDISCRETE1 - 6

nviCOUNT1

nvoCOUNT1 - 2

nvoCOUNTinc1 - 2

50

Figure 4-3 on the page which follows illustrates the Rooftop Maintenance (RTUMNT1) Table. The maintenance values displayed in this table are read-only values that show the current value of the CPP points that have been mapped to the Lonworks variables as the points exist in the CPP system element. These values are updated every 30 seconds. An expla-nation of each value in the table follows. Note that the valid display ranges are dependent on the point.

Indicates the commanded space temperature.

Indicates the commanded temperature setpoint.

Indicates the space temperature.

Indicates the rooftop's operating mode.


Indicates the current primary heat capacity in percent full scale.

Indicates the current secondary heat capacity in percent full scale.

Indicates the current cooling capacity in percent full scale.

Indicates the current economizer position in percent full scale.

Indicates the current fan speed in percent full scale.Note: Most CPP rooftops do not contain this point.

Indicates the alarm status of the chiller.

Notes: Most CPP rooftops do not contain this point.


Indicates the commanded temperature setpoint offset.

Notes: Most CPP rooftops do not contain this point.Metric points will always assume ^T, even if the point ismapped to a temperature.

RooftopMaintenance(RTUMNT1)Table 1

nviSpaceTemp

nvoUnitStatus.mode

nvoSpaceTemp

nviSetPoint







nviOccSchedule

nviSetptOffset

51

Figure 4-3Rooftop Maintenance(RTUMNT1)Table 1

52

Indicates the commanded outside air temperature.

Indicates the commanded outside air relative humidity.

Indicates the setpoint temperature.

Indicates the outside air temperature.

Indicates the outside air relative humidity.

Indicates the commanded space relative humidity.

Indicates the commanded CO2 level in ppm.

Indicates the commanded CO2 level in ppm.

Indicates an additional rooftop commanded operating temperature.

Indicate additional rooftop operating temperatures.

Indicates an additional rooftop commanded operating pressure.

Indicate additional rooftop operating pressures.

Figure 4-4 illustrates the Rooftop Maintenance (RTUMNT2) Table. The maintenance values displayed in this table are read-only values that show the current value of the CPP points that have been mapped to the Lonworks variables as the points exist in the CPP system element. These values are updated every 30 seconds. An explanation of each value in the table follows. Note that the valid display ranges are dependent on the point.

Indicate rooftop commanded parameters in percentage.

Indicate additional rooftop operating parameters in percentage.

Indicate additional rooftop differential temperatures.

Indicate additional discrete commanded operating parameters.

nvoEffectSetpt

nvoOutsideTemp

nvoOutsideRH

nviSpaceRH

nviCO2

nvoCO2

nviTEMP1

nvoTEMP1-4

RooftopMaintenance(RTUMNT2)Table 2

nviPRESS1

nvoPRESS1 - 2

nvoPCT1-3

nvoTEMPDIFF1 - 2

nviDISCRETE1 - 3

nviPCT1-2

nviOutsideTemp

nviOutsideRH

53

Indicate additional discrete commanded operating parameters.

Indicates the commanded CO2 threshold value.

Indicates the commanded occupied cooling setpoint.

Indicates the commanded cooling setpoint in standby mode.


Indicates the commanded unoccupied cooling setpoint.

Indicates the commanded occupied heating setpoint.

Indicates the commanded heating setpoint in standby mode.


Indicates the commanded unoccupied heating setpoint.

Indicates a rooftop commanded analog or multi-state parameter.


Indicate rooftop analog or multi-state values.


Indicates rooftop analog or multi-state values.







nciSetpnts.unocc_heat

nviCOUNT1

nvoCOUNT1 - 2

nvoCOUNTinc1 - 2

nvoDISCRETE1 - 8

nciCO2Limit

54

Figure 4-4Rooftop Maintenance(RTUMNT 2)Table 2

55

Figure 4-5 on the page which follows illustrates the Generic Maintenance (GNRCMNT1) Table. The maintenance values displayed in this table are read-only values that show the current value of the CPP points that have been mapped to the Lonworks variables as the points exist in the CPP system element. These values are updated every 30 seconds. An expla-nation of each value in the table follows. Note that the valid display ranges are dependent on the point.

Indicates the controller's operating mode.

Note: Most CPP controllers do not contain this point.

Indicates the current primary heat capacity in percent full scale.

Indicates the current secondary heat capacity in percent full scale.

Indicates the current cooling capacity in percent full scale.

Indicates the current economizer position in percent full scale.

Indicates the current fan speed in percent full scale.

Indicates the alarm status of the controller.



Indicates an additional controller commanded operating temperature.

Indicate additional controller operating temperatures.

Indicate additional controller commanded operating pressures.

Note: Most CPP controllers do not allow write access to this point.

Use these 6 decisions to specify the names of the analog CPP point that will indicate additional controller operating pressures.

Indicate additional controller differential temperatures.


GenericMaintenance(GNRCMNT1)Table 1

nvoUnitStatus.mode







nviOccSchedule

nviTEMP1 - 3

nvoTEMP1 - 8

nviPRESS1 - 2

nvoTEMPDIFF1 - 2

nvoPRESS1 - 6

56

Figure 4-3Generic Maintenance(GNRCMNT1)Table 1

57

Figure 4-6 on the page which follows illustrates the Generic Maintenance (GNRCMNT2) Table. The maintenance values displayed in this table are read-only values that show the current value of the CPP points that have been mapped to the Lonworks variables as the points exist in the CPP system element. These values are updated every 30 seconds. An expla-nation of each value in the table follows. Note that the valid display ranges are dependent on the point.

Indicate additional controller commanded parameters in percentage.

Indicate additional controller operating parameters in percentage.

Indicate additional commanded discrete operating parameters.

Indicate additional discrete operating parameters.

Indicates the commanded occupied cooling setpoint.

Indicates the commanded cooling setpoint in standby mode.

Note: Most CPP controllers do not use this mode.

Indicates the commanded unoccupied cooling setpoint.

Indicates the commanded occupied heating setpoint.

Indicates the commanded heating setpoint in standby mode.

Note: Most CPP controllers do not contain this point.

Indicates a commanded parameter in PPM.

Indicates an analog value in PPM.

Indicates a commanded analog or multi-state parameter.


Indicate analog or multi-state values.


Indicate analog or multi-state values.


Generic MappingMaintenance(GNRCMNT2)Table 2

nvoPCT1 - 4

nviDISCRETE1 - 3

nvoDISCRETE1 - 8






nviPCT1 - 2

nviPPM

nvoPPM

nviCOUNT1

nvoCOUNT1 - 2

nvoCOUNTinc1 - 2

58

Figure 4-6Generic Mapping 2Maintenance (GNRCMNT2)Table

59

Figure 4-7 below illustrates the Communication Status Maintenance(COMMSTAT) Table. The maintenance values displayed in this table are read-only values that show diagnostic data about LonWorks-to-CPP system element communication. These values are updated every 30 seconds. An explanation of each value in the table follows.

Note: This information is primarily intended to be used by the Lonsystems integrator for troubleshooting.

CommunicationStatusMaintenance(COMMSTAT)TableFigure 4-7Communications StatusMaintenance (COMMSTAT)Table

60

Num SuccessfulMessages

Num Failed Messages

Communication History1 - 4

CommunicationType

Successful?

Indicates the number of successful read, write, and other communication messages sent from LonWorks to the CPP system element. This value is a running total of the number of successful messages detected since the last communication reset. It is not reset on cycling CIAT TRANS-LATOR power. It can be reset, however, using the CONFIG Table's Reset Comm. Counters decision.

Valid Display 0 - 65,000

Indicates the number of unsuccessful read, write, and other communica-tion messages sent from LonWorks to the CPP system element. This value is a running total of the number of unsuccessful messages detected since the last communication reset. It is not reset on cycling power to the CIAT Translator. It can be reset, however, using the CONFIG Table's Reset Comm. Counters decision.

Valid Display 0 - 65,000

These 4 decisions display the below-listed data about the four most recent LonWorks-to-CPP communication messages.

Indicates the type of communication message.

Valid Display 1 = Read Network Variable2 = Write Network Variable3 = Other

Indicates whether or not this communication was successful.

Valid Display Yes/No

61

Figure 4-8 below illustrates the Messages Maintenance (MESSAGES) Table. The maintenance values displayed in this table are read-only values that show diagnostic data about LonWorks-to-CPP system element communication messages. These values are updated every 30 seconds. An explanation of each value in the table follows.

Note: This information is primarily intended to be used by the Lonsystems integrator for troubleshooting.

MessagesMaintenance(MESSAGES)Table

Figure 4-8Messages Maintenance(MESSAGES)Table

62

LON Message 1 - 10 These 10 decisions display diagnostic information about the 10 most recent LonWorks-to-CPP communication messages.

Valid Display Self configurationRead all NVsPropagate NV#Set NV#Read NV#

where: NV = Network Variable# = Number of the NetworkVariable

The Propagate and Set commands both refer to writes to CPP points. Propagate indicates that the value has not changed, but the CIAT Translator's 30 second refresh has caused Lonworks to write to the CPP point again. Set indicates that Lonworks has written a new value to the CPP point.

Appendix

63

This section contains examples of actual configurations for a chiller, rooftop, and generic template, along with a list of LON SNVTs and corresponding CPP point names and descriptions.

Appendix

64

Figure A-2Sample Configuration forCHLRMAP1 Table

Job

Site

:LE

I Add

ress

:0,

211

Atta

ched

Dev

ice:

19XR

IIIA

ttach

ed D

evic

e Add

ress

:0,

1LO

N P

rofil

e:C

hille

r Pro

file

CHLR

MAP

1SN

VT T

ype

R

ead

CPP

Poi

ntC

PP P

oint

or

Writ

e?

D

escr

iptio

nN

ame

nviC

hille

rEna

ble

......

......

......

....S

NVT

_sw

itch

POIN

T01.

.....

W...

......

......

......

...C

hille

r Sta

rt/St

op...

......

......

......

......

......

CH

IL_S

_Snv

iCoo

lSet

pt...

......

......

......

......

SNVT

_tem

p_p

POIN

T02.

.....

W...

......

......

......

...Le

avin

g C

hille

d W

ater

Con

trol P

oint

.....

LCW

_STP

Tnv

oOnO

ff...

......

......

......

......

.....

SNVT

_sw

itch

POIN

T03.

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoA

ctive

Setp

t....

......

......

......

.SN

VT_t

emp_

pPO

INT0

4....

..R

......

......

......

......

.Lea

ving

Chi

lled

Wat

er C

ontro

l Poi

nt...

..LC

W_S

TPT

nviC

apac

ityLi

m...

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT0

5....

..W

......

......

......

......

Activ

e D

eman

d Li

mit

......

......

......

......

...D

EM_L

IMnv

iHea

tSet

pt...

......

......

......

......

SNVT

_tem

p_p

POIN

T06.

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nvoA

ctua

lCap

acity

......

......

.....

SNVT

_lev

_per

cent

POIN

T07.

.....

R...

......

......

......

....M

otor

Per

cent

Kilo

wat

ts...

......

......

......

.KW

_Pnv

oCap

acity

Lim

......

......

......

....S

NVT

_lev

_per

cent

POIN

T08.

.....

R...

......

......

......

....A

ctiv

e D

eman

d Li

mit

......

......

......

......

...D

EM_L

IMnv

oLvg

CHW

Tem

p...

......

......

....S

NVT

_tem

p_p

POIN

T09.

.....

R...

......

......

......

....L

eavi

ng C

hille

d Wat

er...

......

......

......

.....

LCW

nvoE

ntC

HW

Tem

p...

......

......

....S

NVT

_tem

p_p

POIN

T10.

.....

R...

......

......

......

....E

nter

ing

Chi

lled

Wat

er...

......

......

......

....E

CW

nvoE

ntC

ND

WTe

mp

......

......

....S

NVT

_tem

p_p

POIN

T11.

.....

R...

......

......

......

....E

nter

ing

Con

dens

er W

ater

......

......

......

ECD

Wnv

oLvg

CNDW

Tem

p...

......

......

..SN

VT_t

emp_

pPO

INT1

2....

..R

......

......

......

......

.Lea

ving

Con

dens

er W

ater

......

......

......

..LC

DW

nvoC

hille

rSta

t.run

_mod

e...

......

SNVT

_chl

r_st

atus

POIN

T13.

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoC

hille

rSta

t.op_

mod

e...

......

.SN

VT_c

hlr_

stat

usPO

INT1

4....

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oChi

llerS

tat.i

n_al

arm

......

.....

SNVT

_chl

r_st

atus

POIN

T15.

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoC

hille

rSta

t.run

_ena

bl...

......

SNVT

_chl

r_st

atus

POIN

T16.

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoC

hille

rSta

t.Loc

al...

......

......

.SN

VT_c

hlr_

stat

usPO

INT1

7....

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oChi

llerS

tat.L

imite

d...

......

....S

NVT

_chl

r_st

atus

POIN

T18.

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoC

hille

rSta

t.chw

_flo

w...

......

.SN

VT_c

hlr_

stat

usPO

INT1

9....

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oChi

llerS

tat.c

ndw

_flo

w...

.....

SNVT

_chl

r_st

atus

POIN

T20.

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nviO

ccSc

hedu

le...

......

......

......

SNVT

_occ

upan

cyPO

INT2

1....

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.

65

Figure A-2Sample Configuration forCHLRMAP2 Table

CHLR

MAP

2SN

VT T

ype

Rea

d or

Writ

e?

CPP

Poi

nt D

escr

iptio

nC

PP P

oint

Nam

env

iTEM

P1...

......

......

......

......

....S

NVT

_tem

p_p

POIN

T22

......

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nvoT

EMP1

......

......

......

......

......

SNVT

_tem

p_p

POIN

T23

......

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoT

EMP2

......

......

......

......

......

SNVT

_tem

p_p

POIN

T24

......

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoT

EMP3

......

......

......

......

......

SNVT

_tem

p_p

POIN

T25

......

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoT

EMP4

......

......

......

......

......

SNVT

_tem

p_p

POIN

T26

......

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoT

EMP5

......

......

......

......

......

SNVT

_tem

p_p

POIN

T27

......

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoT

EMP6

......

......

......

......

......

SNVT

_tem

p_p

POIN

T28

......

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nviP

RES

S1...

......

......

......

......

.SN

VT_p

ress

POIN

T29

......

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nvoP

RES

S1...

......

......

......

......

SNVT

_pre

ssPO

INT3

0...

...R

......

......

......

......

.Eva

pora

tor R

efrig

Pre

ssur

e...

......

......

...ER

Pnv

oPR

ESS2

......

......

......

......

...SN

VT_p

ress

POIN

T31

......

R...

......

......

......

....C

onde

nser

Ref

rig P

ress

ure

......

......

......

CRP

nvoP

RES

S3...

......

......

......

......

SNVT

_pre

ssPO

INT3

2...

...R

......

......

......

......

.Oil

Pum

p D

elta

P...

......

......

......

......

.....

OIL

PDnv

oPR

ESS4

......

......

......

......

...SN

VT_p

ress

POIN

T33

......

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoP

CT1

......

......

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT3

4...

...R

......

......

......

......

.Ave

rage

Line

Cur

rent

......

......

......

......

...AM

PS_%

nvoP

CT2

......

......

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT3

5...

...R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oTEM

PDIF

F1...

......

......

......

.SN

VT_t

emp_

diff_

pPO

INT3

6...

...R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oTEM

PDIF

F2...

......

......

......

.SN

VT_t

emp_

diff_

pPO

INT3

7...

...R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

iDIS

CR

ETE1

......

......

......

.....S

NVT

_sw

itch

POIN

T38

......

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nviD

ISC

RET

E2...

......

......

......

..SN

VT_s

witc

hPO

INT3

9...

...W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

oDIS

CRET

E1...

......

......

......

.SN

VT_s

witc

hPO

INT4

0...

...R

......

......

......

......

.Chi

ller S

tart/

Stop

......

......

......

......

......

...C

HIL

_S_S

nvoD

ISCR

ETE2

......

......

......

....S

NVT

_sw

itch

POIN

T41

......

R...

......

......

......

....C

hille

d W

ater

Flo

w S

tatu

s...

......

......

....C

HW

_FLO

Wnv

oDIS

CRET

E3...

......

......

......

.SN

VT_s

witc

hPO

INT4

2...

...R

......

......

......

......

.Con

dens

er W

ater

Flo

w S

tatu

s....

......

...C

DW

_FLO

Wnv

oDIS

CRET

E4...

......

......

......

.SN

VT_s

witc

hPO

INT4

3...

...R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oDIS

CRET

E5...

......

......

......

.SN

VT_s

witc

hPO

INT4

4...

...R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oDIS

CRET

E6...

......

......

......

.SN

VT_s

witc

hPO

INT4

5...

...R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

iCO

UNT1

......

......

......

......

....S

NVT

_cou

ntPO

INT4

6...

...W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

oCO

UNT1

......

......

......

......

...SN

VT_c

ount

POIN

T47

......

R...

......

......

......

....C

ontro

l Mod

e...

......

......

......

......

......

......

MO

DE

nvoC

OUN

T2...

......

......

......

......

SNVT

_cou

ntPO

INT4

8...

...R

......

......

......

......

.Run

Sta

tus

......

......

......

......

......

......

......

STAT

US

nvoC

OUN

Tinc

1...

......

......

......

..SN

VT_c

ount

_inc

POIN

T49

......

R...

......

......

......

....S

yste

m A

larm

/Ale

rt...

......

......

......

......

..SY

S_AL

Mnv

oCO

UNTi

nc2

......

......

......

.....S

NVT

_cou

nt_i

ncPO

INT5

0...

...R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..

66

Figure A-3 CHLRMAP1 Table SNVTs and CPP Points

LEI A

ddre

ss:

Atta

ched

Dev

ice:

Atta

ched

Dev

ice A

ddre

ss:

LON

Pro

file:

(NA)

Mea

ns n

ot g

ener

ally

app

licab

le to

CP

P

CHLR

MAP

1...

......

......

......

......

SNVT

Typ

eR

ead

or W

rite?

.. C

PP P

oint

Des

crip

tion

nviC

hille

rEna

ble

......

......

......

....S

NVT

_sw

itch

POIN

T01

W...

......

......

......

...C

hille

r Sta

rt/St

op (1

/0)

nviC

oolS

etpt

......

......

......

......

...SN

VT_t

emp_

pPO

INT0

2W

......

......

......

......

Chi

lled

Wat

er C

ontro

l Tem

p (d

egF)

nvoO

nOff

......

......

......

......

......

..SN

VT_s

witc

hPO

INT0

3R

......

......

......

......

.Chi

ller O

n/O

ff (1

/0) (

NA)

nvoA

ctive

Setp

t....

......

......

......

.SN

VT_t

emp_

pPO

INT0

4R

......

......

......

......

.Chi

lled

Wat

er C

ontro

l Tem

p (d

egF)

nviC

apac

ityLi

m...

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT0

5W

......

......

......

......

Activ

e D

eman

d Li

mit

(%)

nviH

eatS

etpt

......

......

......

......

...SN

VT_t

emp_

pPO

INT0

6W

......

......

......

......

Hot

Wat

er C

ontro

l Tem

p (d

egF)

nvoA

ctua

lCap

acity

......

......

.....

SNVT

_lev

_per

cent

POIN

T07

R...

......

......

......

....P

ecen

t Cap

acity

(%)

nvoC

apac

ityLi

m...

......

......

......

.SN

VT_l

ev_p

erce

ntPO

INT0

8R

......

......

......

......

.Act

ive

Dem

and

Lim

it (%

)nv

oLvg

CHW

Tem

p...

......

......

....S

NVT

_tem

p_p

POIN

T09

R...

......

......

......

....L

eavi

ng C

hille

d W

ater

Tem

p (d

egF)

nvoE

ntC

HW

Tem

p...

......

......

....S

NVT

_tem

p_p

POIN

T10

R...

......

......

......

....E

nter

ing

Chi

lled

Wat

er T

emp

(deg

F)nv

oEnt

CN

DW

Tem

p...

......

......

.SN

VT_t

emp_

pPO

INT1

1R

......

......

......

......

.Lea

ving

Con

d W

ater

Tem

p (d

egF)

nvoL

vgCN

DWTe

mp

......

......

.....

SNVT

_tem

p_p

POIN

T12

R...

......

......

......

....E

nter

ing

Con

d W

ater

Tem

p (d

egF)

nvoC

hille

rSta

t.run

_mod

e...

......

SNVT

_chl

r_st

atus

POIN

T13

R...

......

......

......

....(

NA)

nvoC

hille

rSta

t.op_

mod

e...

......

.SN

VT_c

hlr_

stat

usPO

INT1

4R

......

......

......

......

.(N

A)nv

oChi

llerS

tat.i

n_al

arm

......

.....

SNVT

_chl

r_st

atus

POIN

T15

R...

......

......

......

....C

hille

r In

Alar

m (1

/0) (

NA)

nvoC

hille

rSta

t.run

_ena

bl...

......

SNVT

_chl

r_st

atus

POIN

T16

R...

......

......

......

....C

hille

r Run

Ena

bled

(1/0

) (N

A)nv

oChi

llerS

tat.L

ocal

......

......

....S

NVT

_chl

r_st

atus

POIN

T17

R...

......

......

......

....C

hille

r Loc

al E

nabl

ed (1

/0) (

NA)

nvoC

hille

rSta

t.Lim

ited

......

......

.SN

VT_c

hlr_

stat

usPO

INT1

8R

......

......

......

......

.Chi

ller D

eman

d Li

mite

d (1

/0) (

NA)

nvoC

hille

rSta

t.chw

_flo

w...

......

.SN

VT_c

hlr_

stat

usPO

INT1

9R

......

......

......

......

.Chi

lled

Wat

er F

low

Det

ecte

d (1

/0)

nvoC

hille

rSta

t.cnd

w_f

low

......

..SN

VT_c

hlr_

stat

usPO

INT2

0R

......

......

......

......

.Con

d W

ater

Flo

w D

etec

ted

(1/0

)nv

iOcc

Sche

dule

......

......

......

...SN

VT_o

ccup

ancy

POIN

T21

W ..

......

......

......

.... G

loba

l CP

P O

ccup

ancy

(>64

)

67

Figure A-4 CHLRMAP2 Table SNVTs and CPP Points

CHLR

MAP

2SN

VT T

ype

Rea

d or

Writ

e?

CPP

Poi

nt D

escr

iptio

nnv

iTEM

P1...

......

......

......

......

....S

NVT

_tem

p_p

POIN

T22

......

W...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP1

......

......

......

......

......

SNVT

_tem

p_p

POIN

T23

......

R...

......

......

......

.....

Tem

pera

ture

(deg

F)nv

oTEM

P2...

......

......

......

......

...SN

VT_t

emp_

pPO

INT2

4...

...R

......

......

......

......

..Te

mpe

ratu

re (d

egF)

nvoT

EMP3

......

......

......

......

......

SNVT

_tem

p_p

POIN

T25

......

R...

......

......

......

.....

Tem

pera

ture

(deg

F)nv

oTEM

P4...

......

......

......

......

...SN

VT_t

emp_

pPO

INT2

6...

...R

......

......

......

......

..Te

mpe

ratu

re (d

egF)

nvoT

EMP5

......

......

......

......

......

SNVT

_tem

p_p

POIN

T27

......

R...

......

......

......

.....

Tem

pera

ture

(deg

F)nv

oTEM

P6...

......

......

......

......

...SN

VT_t

emp_

pPO

INT2

8...

...R

......

......

......

......

..Te

mpe

ratu

re (d

egF)

nviP

RES

S1...

......

......

......

......

.SN

VT_p

ress

POIN

T29

......

W...

......

......

......

....P

ress

ure

(PSI

)nv

oPR

ESS1

......

......

......

......

...SN

VT_p

ress

POIN

T30

......

R...

......

......

......

.....

Pres

sure

(PSI

)nv

oPR

ESS2

......

......

......

......

...SN

VT_p

ress

POIN

T31

......

R...

......

......

......

.....

Pres

sure

(PSI

)nv

oPR

ESS3

......

......

......

......

...SN

VT_p

ress

POIN

T32

......

R...

......

......

......

.....

Pres

sure

(PSI

)nv

oPR

ESS4

......

......

......

......

...SN

VT_p

ress

POIN

T33

......

R...

......

......

......

.....

Pres

sure

(PSI

)nv

oPCT

1...

......

......

......

......

.....S

NVT

_lev

_per

cent

POIN

T34

......

R...

......

......

......

.....

Perc

ent (

%)

nvoP

CT2

......

......

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT3

5...

...R

......

......

......

......

..Pe

rcen

t (%

)nv

oTEM

PDIF

F1...

......

......

......

.SN

VT_t

emp_

diff_

pPO

INT3

6...

...R

......

......

......

......

..D

elta

Tem

pera

ture

(^F)

nvoT

EMPD

IFF2

......

......

......

....S

NVT

_tem

p_di

ff_p

POIN

T37

......

R...

......

......

......

.....

Del

ta T

empe

ratu

re (^

F)nv

iDIS

CR

ETE1

......

......

......

.....S

NVT

_sw

itch

POIN

T38

......

W...

......

......

......

....D

iscr

ete

(1/0

)nv

iDIS

CR

ETE2

......

......

......

.....S

NVT

_sw

itch

POIN

T39

......

W...

......

......

......

....D

iscr

ete

(1/0

)nv

oDIS

CRET

E1...

......

......

......

.SN

VT_s

witc

hPO

INT4

0...

...R

......

......

......

......

..D

iscr

ete

(1/0

)nv

oDIS

CRET

E2...

......

......

......

.SN

VT_s

witc

hPO

INT4

1...

...R

......

......

......

......

..D

iscr

ete

(1/0

)nv

oDIS

CRET

E3...

......

......

......

.SN

VT_s

witc

hPO

INT4

2...

...R

......

......

......

......

..D

iscr

ete

(1/0

)nv

oDIS

CRET

E4...

......

......

......

.SN

VT_s

witc

hPO

INT4

3...

...R

......

......

......

......

..D

iscr

ete

(1/0

)nv

oDIS

CRET

E5...

......

......

......

.SN

VT_s

witc

hPO

INT4

4...

...R

......

......

......

......

..D

iscr

ete

(1/0

)nv

oDIS

CRET

E6...

......

......

......

.SN

VT_s

witc

hPO

INT4

5...

...R

......

......

......

......

..D

iscr

ete

(1/0

)nv

iCO

UNT1

......

......

......

......

....S

NVT

_cou

ntPO

INT4

6...

...W

......

......

......

......

.Gen

eric

ana

log

or d

iscr

ete

(0-6

5535

)nv

oCO

UNT1

......

......

......

......

...SN

VT_c

ount

POIN

T47

......

R...

......

......

......

.....

Gen

eric

ana

log

or d

iscr

ete

(0-6

5535

)nv

oCO

UNT2

......

......

......

......

...SN

VT_c

ount

POIN

T48

......

R...

......

......

......

.....

Gen

eric

ana

log

or d

iscr

ete

(0-6

5535

)nv

oCO

UNTi

nc1

......

......

......

.....S

NVT

_cou

nt_i

ncPO

INT4

9...

...R

......

......

......

......

..G

ener

ic a

nalo

g or

dis

cret

e (-3

2767

- 327

67)

nvoC

OUN

Tinc

2...

......

......

......

..SN

VT_c

ount

_inc

POIN

T50

......

R...

......

......

......

.....

Gen

eric

ana

log

or d

iscr

ete

(-327

67 - 3

2767

)

68

Figure A-5Sample Configuration forRTUMAP1 Table

Job

Site

:LE

I Add

ress

:0,

204

Atta

ched

Dev

ice:

48H

G C

entu

rian

Atta

ched

Dev

ice A

ddre

ss:

0, 1

LON

Pro

file:

Roo

ftop

RTUM

AP1

SNVT

Typ

eR

ead

or W

rite?

C

PP P

oint

Des

crip

tion

CPP

Poi

nt N

ame

nviS

pace

Tem

p...

......

......

......

...SN

VT_t

emp_

pPO

INT0

1...

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

iSet

Poin

t....

......

......

......

......

.SN

VT_t

emp_

pPO

INT0

2...

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

oSpa

ceTe

mp.

......

......

......

....S

NVT

_tem

p_p

POIN

T03

.....

R...

......

......

......

....S

pace

Tem

pera

ture

......

......

......

......

.....

SPT

nvoU

nitS

tatu

s.m

ode

......

......

...SN

VT_h

vac_

stat

usPO

INT0

4...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oUni

tSta

tus.

heat

_out

_p...

...SN

VT_h

vac_

stat

usPO

INT0

5...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oUni

tSta

tus.

heat

_out

_s...

...SN

VT_h

vac_

stat

usPO

INT0

6...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oUni

tSta

tus.

cool

_out

......

.....

SNVT

_hva

c_st

atus

POIN

T07

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoU

nitS

tatu

s.ec

on_o

ut...

......

SNVT

_hva

c_st

atus

POIN

T08

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoU

nitS

tatu

s.fa

n_ou

t....

......

..SN

VT_h

vac_

stat

usPO

INT0

9...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oUni

tSta

tus.

in_a

larm

......

.....

SNVT

_hva

c_st

atus

POIN

T10

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nviO

ccSc

hedu

le...

......

......

......

SNVT

_occ

upan

cyPO

INT1

1...

..W

......

......

......

......

Occ

upan

cy S

ched

ule

......

......

......

......

..O

CC

PC65

Env

iSet

PtO

ffset

......

......

......

......

SNVT

_tem

p_p

POIN

T12

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nviO

utsid

eTem

p...

......

......

......

SNVT

_tem

p_p

POIN

T13

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nviO

utsid

eRH

......

......

......

......

.SN

VT_l

ev_p

erce

ntPO

INT1

4...

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

oEffe

ctSe

tpt.

......

......

......

.....

SNVT

_tem

p_p

POIN

T15

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoO

utsid

eTem

p...

......

......

.....

SNVT

_tem

p_p

POIN

T16

.....

R...

......

......

......

....O

utdo

or A

ir Tem

pera

ture

......

......

......

...O

ATnv

oOut

sideR

H...

......

......

......

...SN

VT_l

ev_p

erce

ntPO

INT1

7...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

iSpa

ceR

H...

......

......

......

......

SNVT

_lev

_per

cent

POIN

T18

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nviC

O2

......

......

......

......

......

.....

SNVT

_ppm

POIN

T19

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nvoC

O2

......

......

......

......

......

....S

NVT

_ppm

POIN

T20

.....

R...

......

......

......

....I

ndoo

r Air

CO

2 Le

vel.

......

......

......

......

...IA

Qnv

iTEM

P1...

......

......

......

......

....S

NVT

_tem

p_p

POIN

T21

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nvoT

EMP1

......

......

......

......

......

SNVT

_tem

p_p

POIN

T22

.....

R...

......

......

......

....S

uppl

y Air

Tem

pera

ture

......

......

......

.....

SAT

nvoT

EMP2

......

......

......

......

......

SNVT

_tem

p_p

POIN

T23

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoT

EMP3

......

......

......

......

......

SNVT

_tem

p_p

POIN

T24

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoT

EMP4

......

......

......

......

......

SNVT

_tem

p_p

POIN

T25

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nviP

RES

S1...

......

......

......

......

.SN

VT_p

ress

_pPO

INT2

6...

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

oPR

ESS1

......

......

......

......

...SN

VT_p

ress

_pPO

INT2

7...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oPR

ESS2

......

......

......

......

...SN

VT_p

ress

_pPO

INT2

8...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..

69

Figure A-6Sample Configurationfor RTUMAP2 Table

RTUM

AP2

SNVT

Typ

eR

ead

or W

rite?

C

PP P

oint

Des

crip

tion

CPP

Poi

nt N

ame

nviP

CT1

SNVT

_lev

_per

cent

POIN

T29

Wnv

iPCT

2....

......

......

......

......

......

SNVT

_lev

_per

cent

POIN

T30

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nvoP

CT1

......

......

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT3

1...

..R

......

......

......

......

.Eco

nom

izer

Pos

ition

......

......

......

......

...EC

ON

OPO

Snv

oPCT

2...

......

......

......

......

.....S

NVT

_lev

_per

cent

POIN

T32

.....

R...

......

......

......

....E

cono

miz

er M

in. P

ositi

on in

Effe

ct...

...M

IN_P

OS

nvoP

CT3

......

......

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT3

3...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oTEM

PDIF

F1...

......

......

......

.SN

VT_t

emp_

diff_

pPO

INT3

4...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oTEM

PDIF

F2...

......

......

......

.SN

VT_t

emp_

diff_

pPO

INT3

5...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

iDIS

CR

ETE1

......

......

......

.....S

NVT

_sw

itch

POIN

T36

.....

W...

......

......

......

...C

urre

ntly

Occ

upie

d...

......

......

......

......

...O

CC

UPI

EDnv

iDIS

CR

ETE2

......

......

......

.....S

NVT

_sw

itch

POIN

T37

.....

W...

......

......

......

...U

nit S

hutd

own

Inpu

t....

......

......

......

...FI

REDO

WN

nviD

ISC

RET

E3...

......

......

......

..SN

VT_s

witc

hPO

INT3

8...

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

oDIS

CRET

E1...

......

......

......

.SN

VT_s

witc

hPO

INT3

9...

..R

......

......

......

......

.Cur

rent

ly O

ccup

ied

......

......

......

......

......

OC

CU

PIED

nvoD

ISCR

ETE2

......

......

......

....S

NVT

_sw

itch

POIN

T40

.....

R...

......

......

......

....S

uppl

y Fa

n St

atus

......

......

......

......

......

FAN

_STA

Tnv

oDIS

CRET

E3...

......

......

......

.SN

VT_s

witc

hPO

INT4

1...

..R

......

......

......

......

.Hea

ting

Stag

e 1

......

......

......

......

......

....H

EAT_

1nv

oDIS

CRET

E4...

......

......

......

.SN

VT_s

witc

hPO

INT4

2...

..R

......

......

......

......

.Hea

ting

Stag

e 2

......

......

......

......

......

....H

EAT_

2nv

oDIS

CRET

E5...

......

......

......

.SN

VT_s

witc

hPO

INT4

3...

..R

......

......

......

......

.Com

pres

sor A

1...

......

......

......

......

......

..C

OM

P_A1

nvoD

ISCR

ETE6

......

......

......

....S

NVT

_sw

itch

POIN

T44

.....

R...

......

......

......

....C

ompr

esso

r B1

......

......

......

......

......

.....

CO

MP_

B1nv

oDIS

CRET

E7...

......

......

......

.SN

VT_s

witc

hPO

INT4

5...

..R

......

......

......

......

.Com

pres

sor C

1...

......

......

......

......

......

..C

OM

P_C

1nv

oDIS

CRET

E8...

......

......

......

.SN

VT_s

witc

hPO

INT4

6...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nc

iCO

2Lim

it...

......

......

......

......

SNVT

_ppm

POIN

T47

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nciS

etPn

ts.o

ccup

ied_

cool

......

SNVT

_tem

p_se

tpt

POIN

T48

.....

W...

......

......

......

...O

ccup

ied

Coo

ling

Setp

oint

......

......

......

OC

SPnc

iSet

Pnts

.sta

ndby

_coo

l....

...SN

VT_t

emp_

setp

tPO

INT4

9...

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nc

iSet

Pnts

.uno

cc_c

ool.

......

...SN

VT_t

emp_

setp

tPO

INT5

0...

..W

......

......

......

......

Uno

ccup

ied

Coo

ling

Setp

oint

......

......

...U

CSP

nciS

etPn

ts.o

ccup

ied_

heat

.....S

NVT

_tem

p_se

tpt

POIN

T51

.....

W...

......

......

......

...O

ccup

ied

Hea

ting

Setp

oint

......

......

......

OH

SPnc

iSet

Pnts

.sta

ndby

_hea

t....

...SN

VT_t

emp_

setp

tPO

INT5

2...

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nc

iSet

Pnts

.uno

cc_h

eat.

......

...SN

VT_t

emp_

setp

tPO

INT5

3...

..W

......

......

......

......

Uno

ccup

ied

Hea

ting

Setp

oint

......

......

..U

HSP

nviC

OUN

T1...

......

......

......

......

.SN

VT_c

ount

POIN

T54

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nvoC

OUN

T1...

......

......

......

......

SNVT

_cou

ntPO

INT5

5...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oCO

UNT2

......

......

......

......

...SN

VT_c

ount

POIN

T56

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoC

OUN

Tinc

1...

......

......

......

..SN

VT_c

ount

_inc

POIN

T57

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoC

OUN

Tinc

2...

......

......

......

..SN

VT_c

ount

_inc

POIN

T58

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

70

Figure A-7RTUMAP1 Table SNVTs and CPP Points

Job

Site

:LE

I Add

ress

:A

ttach

ed D

evic

e:A

ttach

ed D

evic

e Add

ress

:LO

N P

rofil

e:(N

A) M

eans

not

gen

eral

ly a

pplic

able

to C

PP

RTUM

AP1

SNVT

Typ

eR

ead

or W

rite?

C

PP P

oint

Des

crip

tion

nviS

pace

Tem

p...

......

......

......

..SN

VT_t

emp_

pPO

INT0

1...

....W

......

......

......

......

Spac

e Tem

pera

ture

(deg

F)nv

iSet

Poin

t....

......

......

......

......

SNVT

_tem

p_p

POIN

T02

......

.W...

......

......

......

...Su

pply

Air

Setp

oint

on

VAV

units

(deg

F)nv

oSpa

ceTe

mp.

......

......

......

...SN

VT_t

emp_

pPO

INT0

3...

....R

......

......

......

......

.Spa

ce T

empe

ratu

re (d

egF)

nvoU

nitS

tatu

s.m

ode

......

......

..SN

VT_h

vac_

stat

usPO

INT0

4...

....R

......

......

......

......

.(N

A)nv

oUni

tSta

tus.

heat

_out

_p...

..SN

VT_h

vac_

stat

usPO

INT0

5...

....R

......

......

......

......

.Hea

ting

Coi

l Val

ve (%

)nv

oUni

tSta

tus.

heat

_out

_s...

..SN

VT_h

vac_

stat

usPO

INT0

6...

....R

......

......

......

......

.Sec

onda

ry H

eatin

g C

oil V

alve

(%) (

NA)

nvoU

nitS

tatu

s.co

ol_o

ut...

......

.SN

VT_h

vac_

stat

usPO

INT0

7...

....R

......

......

......

......

.Coo

ling

Coi

l Val

ve (%

)nv

oUni

tSta

tus.

econ

_out

......

..SN

VT_h

vac_

stat

usPO

INT0

8...

....R

......

......

......

......

.Eco

nom

izer

(%)

nvoU

nitS

tatu

s.fa

n_ou

t....

......

.SN

VT_h

vac_

stat

usPO

INT0

9...

....R

......

......

......

......

.Fan

Spe

ed (%

)nv

oUni

tSta

tus.

in_a

larm

......

....S

NVT

_hva

c_st

atus

POIN

T10

......

.R...

......

......

......

....D

iscr

ete

Alar

m p

oint

(1/0

)nv

iOcc

Sche

dule

.....

......

......

... S

NVT

_occ

upan

cy

POIN

T11

......

. W ..

......

......

......

.... G

loba

l CP

P O

ccup

ancy

(>64

)nv

iSet

PtO

ffset

......

......

......

.....

SNVT

_tem

p_p

POIN

T12

......

.W...

......

......

......

...Te

mpe

ratu

re (d

egF)

nviO

utsid

eTem

p...

......

......

.....

SNVT

_tem

p_p

POIN

T13

......

.W...

......

......

......

...O

utdo

or A

ir Tem

pera

ture

(deg

F)nv

iOut

sideR

H...

......

......

......

...SN

VT_l

ev_p

erce

ntPO

INT1

4...

....W

......

......

......

......

Out

door

Air

RH

(%)

nvoE

ffect

Setp

t....

......

......

......

.SN

VT_t

emp_

pPO

INT1

5...

....R

......

......

......

......

.Con

trollin

g Se

tpoi

nt (d

egF)

nvoO

utsid

eTem

p...

......

......

....S

NVT

_tem

p_p

POIN

T16

......

.R...

......

......

......

....O

utdo

or A

ir Tem

pera

ture

(deg

F)nv

oOut

sideR

H...

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT1

7...

....R

......

......

......

......

.Out

door

Air

RH

(%)

nviS

pace

RH

......

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT1

8...

....W

......

......

......

......

Spac

e R

H (%

)nv

iCO

2...

......

......

......

......

......

.SN

VT_p

pmPO

INT1

9...

....W

......

......

......

......

IAQ

(PPM

)nv

oCO

2...

......

......

......

......

......

SNVT

_ppm

POIN

T20

......

.R...

......

......

......

....I

AQ (P

PM)

nviT

EMP1

......

......

......

......

......

SNVT

_tem

p_p

POIN

T21

......

.W...

......

......

......

...Te

mpe

ratu

re (d

egF)

nvoT

EMP1

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T22

......

.R...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP2

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T23

......

.R...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP3

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T24

......

.R...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP4

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T25

......

.R...

......

......

......

....T

empe

ratu

re (d

egF)

nviP

RES

S1...

......

......

......

......

SNVT

_pre

ss_p

POIN

T26

......

.W...

......

......

......

...Pr

essu

re (“

H2O

)nv

oPR

ESS1

......

......

......

......

..SN

VT_p

ress

_pPO

INT2

7...

....R

......

......

......

......

.Pre

ssur

e (“H

2O)

nvoP

RES

S2...

......

......

......

.....

SNVT

_pre

ss_p

POIN

T28

......

.R...

......

......

......

....P

ress

ure (

“H2O

)

71

Figure A-8RTUMAP2 Table SNVTs and CPP Points

RTUM

AP2

SNVT

Typ

eR

ead

or W

rite?

C

PP P

oint

Des

crip

tion

nviP

CT1.

......

......

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT2

9...

....W

......

......

......

......

Perc

ent (

%)

nviP

CT2.

......

......

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT3

0...

....W

......

......

......

......

Perc

ent (

%)

nvoP

CT1

......

......

......

......

......

.SN

VT_l

ev_p

erce

ntPO

INT3

1...

....R

......

......

......

......

.Per

cent

(%)

nvoP

CT2

......

......

......

......

......

.SN

VT_l

ev_p

erce

ntPO

INT3

2...

....R

......

......

......

......

.Per

cent

(%)

nvoP

CT3

......

......

......

......

......

.SN

VT_l

ev_p

erce

ntPO

INT3

3...

....R

......

......

......

......

.Per

cent

(%)

nvoT

EMPD

IFF1

......

......

......

...SN

VT_t

emp_

diff_

pPO

INT3

4...

....R

......

......

......

......

.Del

ta T

empe

ratu

re (^

F)nv

oTEM

PDIF

F2...

......

......

......

SNVT

_tem

p_di

ff_p

POIN

T35

......

.R...

......

......

......

....D

elta

Tem

pera

ture

(^F)

nviD

ISC

RET

E1...

......

......

......

.SN

VT_s

witc

hPO

INT3

6...

....W

......

......

......

......

Dis

cret

e (1

/0)

nviD

ISC

RET

E2...

......

......

......

.SN

VT_s

witc

hPO

INT3

7...

....W

......

......

......

......

Dis

cret

e (1

/0)

nviD

ISC

RET

E3...

......

......

......

.SN

VT_s

witc

hPO

INT3

8...

....W

......

......

......

......

Dis

cret

e (1

/0)

nvoD

ISCR

ETE1

......

......

......

...SN

VT_s

witc

hPO

INT3

9...

....R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE2

......

......

......

...SN

VT_s

witc

hPO

INT4

0...

....R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE3

......

......

......

...SN

VT_s

witc

hPO

INT4

1...

....R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE4

......

......

......

...SN

VT_s

witc

hPO

INT4

2...

....R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE5

......

......

......

...SN

VT_s

witc

hPO

INT4

3...

....R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE6

......

......

......

...SN

VT_s

witc

hPO

INT4

4...

....R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE7

......

......

......

...SN

VT_s

witc

hPO

INT4

5...

....R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE8

......

......

......

...SN

VT_s

witc

hPO

INT4

6...

....R

......

......

......

......

.Dis

cret

e (1

/0)

nciC

O2L

imit

......

......

......

......

..SN

VT_p

pmPO

INT4

7...

....W

......

......

......

......

IAQ

Set

poin

t (PP

M)

nciS

etPn

ts.o

ccup

ied_

cool

.....

SNVT

_tem

p_se

tpt

POIN

T48

......

.W...

......

......

......

...Te

mpe

ratu

re S

etpo

int (

degF

)nc

iSet

Pnts

.sta

ndby

_coo

l....

..SN

VT_t

emp_

setp

tPO

INT4

9...

....W

......

......

......

......

(NA)

nciS

etPn

ts.u

nocc

_coo

l....

.....

SNVT

_tem

p_se

tpt

POIN

T50

......

.W...

......

......

......

...Te

mpe

ratu

re S

etpo

int (

degF

)nc

iSet

Pnts

.occ

upie

d_he

at...

.SN

VT_t

emp_

setp

tPO

INT5

1...

....W

......

......

......

......

Tem

pera

ture

Set

poin

t (de

gF)

nciS

etPn

ts.s

tand

by_h

eat.

.....

SNVT

_tem

p_se

tpt

POIN

T52

......

.W...

......

......

......

...(N

A)nc

iSet

Pnts

.uno

cc_h

eat.

......

..SN

VT_t

emp_

setp

tPO

INT5

3...

....W

......

......

......

......

Tem

pera

ture

Set

poin

t (de

gF)

nviC

OUN

T1...

......

......

......

......

SNVT

_cou

ntPO

INT5

4...

....W

......

......

......

......

Gen

eric

ana

log

or d

iscr

ete

(0-6

5535

)nv

oCO

UNT1

......

......

......

......

..SN

VT_c

ount

POIN

T55

......

.R...

......

......

......

....G

ener

ic a

nalo

g or

dis

cret

e (0

-655

35)

nvoC

OUN

T2...

......

......

......

.....

SNVT

_cou

ntPO

INT5

6...

....R

......

......

......

......

.Gen

eric

ana

log

or d

iscr

ete

(0-6

5535

)nv

oCO

UNTi

nc1

......

......

......

....S

NVT

_cou

nt_i

ncPO

INT5

7...

....R

......

......

......

......

.Gen

eric

ana

log

or d

iscr

ete

(-327

67 - 3

2767

)nv

oCO

UNTi

nc2

......

......

......

....S

NVT

_cou

nt_i

ncPO

INT5

8...

....R

......

......

......

......

.Gen

eric

ana

log

or d

iscr

ete

(-327

67 - 3

2767

)

72

Figure A-9Sample Configuration forGNRCMAP1 Table

Job

Site

:LE

I Add

ress

:0,

182

Atta

ched

Dev

ice:

Prem

ierL

ink

Atta

ched

Dev

ice A

ddre

ss:

0, 3

1LO

N P

rofil

e:G

ener

ic

GNR

CMAP

1SN

VT T

ype

CPP

Poi

nt N

ame

nvoU

nitS

tatu

s.m

ode

SNVT

_hva

c_st

atus

POIN

T01

Rea

d or

Writ

e?

CPP

Poi

nt D

escr

iptio

n R

nvoU

nitS

tatu

s.he

at_o

ut_p

.....

SNVT

_hva

c_st

atus

POIN

T02

......

.R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoU

nitS

tatu

s.he

at_o

ut_s

.....

SNVT

_hva

c_st

atus

POIN

T03

......

.R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoU

nitS

tatu

s.co

ol_o

ut...

......

.SN

VT_h

vac_

stat

usPO

INT0

4...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oUni

tSta

tus.

econ

_out

......

..SN

VT_h

vac_

stat

usPO

INT0

5...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oUni

tSta

tus.

fan_

out.

......

....S

NVT

_hva

c_st

atus

POIN

T06

......

.R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoU

nitS

tatu

s.in

_ala

rm...

......

.SN

VT_h

vac_

stat

usPO

INT0

7...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

iOcc

Sche

dule

......

......

......

..SN

VT_o

ccup

ancy

POIN

T08

......

.W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nviT

EMP1

......

......

......

......

......

SNVT

_tem

p_p

POIN

T09

......

.W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nviT

EMP2

......

......

......

......

......

SNVT

_tem

p_p

POIN

T10

......

.W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nviT

EMP3

......

......

......

......

......

SNVT

_tem

p_p

POIN

T11

......

.W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nvoT

EMP1

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T12

......

.R...

......

......

......

....S

uppl

y Air

Tem

pera

ture

......

......

......

.....

SAT

nvoT

EMP2

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T13

......

.R...

......

......

......

....O

utdo

or A

ir Tem

pera

ture

......

......

......

...O

ATnv

oTEM

P3...

......

......

......

......

..SN

VT_t

emp_

pPO

INT1

4...

....R

......

......

......

......

.Spa

ce T

empe

ratu

re...

......

......

......

......

..SP

Tnv

oTEM

P4...

......

......

......

......

..SN

VT_t

emp_

pPO

INT1

5...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oTEM

P5...

......

......

......

......

..SN

VT_t

emp_

pPO

INT1

6...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oTEM

P6...

......

......

......

......

..SN

VT_t

emp_

pPO

INT1

7...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oTEM

P7...

......

......

......

......

..SN

VT_t

emp_

pPO

INT1

8...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oTEM

P8...

......

......

......

......

..SN

VT_t

emp_

pPO

INT1

9...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

iPR

ESS1

......

......

......

......

...SN

VT_p

ress

_pPO

INT2

0...

....W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

iPR

ESS2

......

......

......

......

...SN

VT_p

ress

POIN

T21

......

.W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nvoP

RES

S1...

......

......

......

.....

SNVT

_pre

ss_p

POIN

T22

......

.R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoP

RES

S2...

......

......

......

.....

SNVT

_pre

ss_p

POIN

T23

......

.R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoP

RES

S3...

......

......

......

.....

SNVT

_pre

ssPO

INT2

4...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oPR

ESS4

......

......

......

......

..SN

VT_p

ress

POIN

T25

......

.R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoP

RES

S5...

......

......

......

.....

SNVT

_pre

ssPO

INT2

6...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oPR

ESS6

......

......

......

......

..SN

VT_p

ress

POIN

T27

......

.R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoT

EMPD

IFF1

......

......

......

...SN

VT_t

emp_

diff_

pPO

INT2

8...

....R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oTEM

PDIF

F2...

......

......

......

SNVT

_tem

p_di

ff_p

POIN

T29

......

.R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

73

Figure A-10Sample Configurationfor GNRCMAP2 Table

GNR

CMAP

2SN

VT T

ype

Rea

d or

Writ

e?

CPP

Poi

nt D

escr

iptio

nC

PP P

oint

Nam

env

iPCT

1SN

VT_l

ev_p

erce

ntPO

INT3

0W

nviP

CT2.

......

......

......

......

......

..SN

VT_l

ev_p

erce

ntPO

INT3

1...

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

oPCT

1...

......

......

......

......

....S

NVT

_lev

_per

cent

POIN

T32

.....

R...

......

......

......

....C

oolin

g %

Tot

al C

apac

ity...

......

......

.....

CC

APnv

oPCT

2...

......

......

......

......

....S

NVT

_lev

_per

cent

POIN

T33

.....

R...

......

......

......

....H

eatin

g %

Tot

al C

apac

ity...

......

......

.....

HC

APnv

oPCT

3...

......

......

......

......

....S

NVT

_lev

_per

cent

POIN

T34

.....

R...

......

......

......

....E

cono

miz

er P

ositi

on...

......

......

......

......

ECO

NPO

Snv

oPCT

4...

......

......

......

......

....S

NVT

_lev

_per

cent

POIN

T35

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nviD

ISC

RET

E1...

......

......

......

.SN

VT_s

witc

hPO

INT3

6...

..W

......

......

......

......

Rem

ote

Occ

upie

d M

ode

......

......

......

....R

MTO

CCnv

iDIS

CR

ETE2

......

......

......

....S

NVT

_sw

itch

POIN

T37

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nviD

ISC

RET

E3...

......

......

......

.SN

VT_s

witc

hPO

INT3

8...

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

oDIS

CRET

E1...

......

......

......

SNVT

_sw

itch

POIN

T39

.....

R...

......

......

......

....S

uppl

y Fa

n R

elay

......

......

......

......

......

..SF

nvoD

ISCR

ETE2

......

......

......

...SN

VT_s

witc

hPO

INT4

0...

..R

......

......

......

......

.Eco

nom

izer

Act

ive

......

......

......

......

......

ECO

Snv

oDIS

CRET

E3...

......

......

......

SNVT

_sw

itch

POIN

T41

.....

R...

......

......

......

....R

emot

e O

ccup

ied

Mod

e...

......

......

......

.RM

TOCC

nvoD

ISCR

ETE4

......

......

......

...SN

VT_s

witc

hPO

INT4

2...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oDIS

CRET

E5...

......

......

......

SNVT

_sw

itch

POIN

T43

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoD

ISCR

ETE6

......

......

......

...SN

VT_s

witc

hPO

INT4

4...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oDIS

CRET

E7...

......

......

......

SNVT

_sw

itch

POIN

T45

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoD

ISCR

ETE8

......

......

......

...SN

VT_s

witc

hPO

INT4

6...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nc

iSet

Pnts

.occ

upie

d_co

ol...

..SN

VT_t

emp_

setp

tPO

INT4

7...

..W

......

......

......

......

Occ

upie

d C

oolin

g Se

tpoi

nt...

......

......

...O

CSP

nciS

etPn

ts.s

tand

by_c

ool.

.....

SNVT

_tem

p_se

tpt

POIN

T48

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nciS

etPn

ts.u

nocc

_coo

l....

.....

SNVT

_tem

p_se

tpt

POIN

T49

.....

W...

......

......

......

...U

nocc

upie

d C

oolin

g Se

tpoi

nt...

......

......

UC

SPnc

iSet

Pnts

.occ

upie

d_he

at...

.SN

VT_t

emp_

setp

tPO

INT5

0...

..W

......

......

......

......

Occ

upie

d H

eatin

g Se

tpoi

nt...

......

......

...O

HSP

nciS

etPn

ts.s

tand

by_h

eat.

.....

SNVT

_tem

p_se

tpt

POIN

T51

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nciS

etPn

ts.u

nocc

_hea

t....

.....

SNVT

_tem

p_se

tpt

POIN

T52

.....

W...

......

......

......

...U

nocc

upie

d H

eatin

g Se

tpoi

nt...

......

.....

UH

SPnv

iPPM

......

......

......

......

......

...SN

VT_p

pmPO

INT5

3...

..W

......

......

......

......

......

......

......

......

......

......

......

......

......

......

.nv

oPPM

......

......

......

......

......

..SN

VT_p

pmPO

INT5

4...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

iCO

UNT1

......

......

......

......

...SN

VT_c

ount

POIN

T55

.....

W...

......

......

......

......

......

......

......

......

......

......

......

......

......

....

nvoC

OUN

T1...

......

......

......

.....

SNVT

_cou

ntPO

INT5

6...

..R

......

......

......

......

......

......

......

......

......

......

......

......

......

......

..nv

oCO

UNT2

......

......

......

......

..SN

VT_c

ount

POIN

T57

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoC

OUN

Tinc

1...

......

......

......

.SN

VT_c

ount

_inc

POIN

T58

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

nvoC

OUN

Tinc

2...

......

......

......

.SN

VT_c

ount

_inc

POIN

T59

.....

R...

......

......

......

......

......

......

......

......

......

......

......

......

......

.....

74

Figure A-11 GNRCMAP1 Table SNVTs and CPP Points

Job

Site

:LE

I Add

ress

:A

ttach

ed D

evic

e:A

ttach

ed D

evic

e Add

ress

:LO

N P

rofil

e:(N

A) M

eans

not

gen

eral

ly a

pplic

able

to C

PP

GNR

CMAP

1SN

VT T

ype

nvoU

nitS

tatu

s.m

ode

SNVT

_hva

c_st

atus

POIN

T01

Rea

d or

Writ

e?

CPP

Poi

nt D

escr

iptio

n R

(NA)

nvoU

nitS

tatu

s.he

at_o

ut_p

.....

SNVT

_hva

c_st

atus

POIN

T02

......

R...

......

......

......

....H

eatin

g C

oil V

alve

(%)

nvoU

nitS

tatu

s.he

at_o

ut_s

.....

SNVT

_hva

c_st

atus

POIN

T03

......

R...

......

......

......

....S

econ

dary

Hea

ting

Coi

l Val

ve (%

)nv

oUni

tSta

tus.

cool

_out

......

....S

NVT

_hva

c_st

atus

POIN

T04

......

R...

......

......

......

....C

oolin

g C

oil V

alve

(%)

nvoU

nitS

tatu

s.ec

on_o

ut...

.....

SNVT

_hva

c_st

atus

POIN

T05

......

R...

......

......

......

....E

cono

miz

er (%

)nv

oUni

tSta

tus.

fan_

out.

......

....S

NVT

_hva

c_st

atus

POIN

T06

......

R...

......

......

......

....F

an S

peed

(%)

nvoU

nitS

tatu

s.in

_ala

rm...

......

.SN

VT_h

vac_

stat

usPO

INT0

7...

...R

......

......

......

......

.Dis

cret

e Al

arm

poi

nt (1

/0)

nviO

ccSc

hedu

le ..

......

......

......

SN

VT_o

ccup

ancy

PO

INT0

8 ...

... W

.....

......

......

......

. Glo

bal C

PP

Occ

upan

cy (>

64)

nviT

EMP1

......

......

......

......

......

SNVT

_tem

p_p

POIN

T09

......

W...

......

......

......

...Te

mpe

ratu

re (d

egF)

nviT

EMP2

......

......

......

......

......

SNVT

_tem

p_p

POIN

T10

......

W...

......

......

......

...Te

mpe

ratu

re (d

egF)

nviT

EMP3

......

......

......

......

......

SNVT

_tem

p_p

POIN

T11

......

W...

......

......

......

...Te

mpe

ratu

re (d

egF)

nvoT

EMP1

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T12

......

R...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP2

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T13

......

R...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP3

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T14

......

R...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP4

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T15

......

R...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP5

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T16

......

R...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP6

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T17

......

R...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP7

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T18

......

R...

......

......

......

....T

empe

ratu

re (d

egF)

nvoT

EMP8

......

......

......

......

.....

SNVT

_tem

p_p

POIN

T19

......

R...

......

......

......

....T

empe

ratu

re (d

egF)

nviP

RES

S1...

......

......

......

......

SNVT

_pre

ss_p

POIN

T20

......

W...

......

......

......

...Pr

essu

re (“

H2O

)nv

iPR

ESS2

......

......

......

......

...SN

VT_p

ress

POIN

T21

......

W...

......

......

......

...Pr

essu

re (P

SI)

nvoP

RES

S1...

......

......

......

.....

SNVT

_pre

ss_p

POIN

T22

......

R...

......

......

......

....P

ress

ure (

“H2O

)nv

oPR

ESS2

......

......

......

......

..SN

VT_p

ress

_pPO

INT2

3...

...R

......

......

......

......

.Pre

ssur

e (“H

2O)

nvoP

RES

S3...

......

......

......

.....

SNVT

_pre

ssPO

INT2

4...

...R

......

......

......

......

.Pre

ssur

e (P

SI)

nvoP

RES

S4...

......

......

......

.....

SNVT

_pre

ssPO

INT2

5...

...R

......

......

......

......

.Pre

ssur

e (P

SI)

nvoP

RES

S5...

......

......

......

.....

SNVT

_pre

ssPO

INT2

6...

...R

......

......

......

......

.Pre

ssur

e (P

SI)

nvoP

RES

S6...

......

......

......

.....

SNVT

_pre

ssPO

INT2

7...

...R

......

......

......

......

.Pre

ssur

e (P

SI)

nvoT

EMPD

IFF1

......

......

......

...SN

VT_t

emp_

diff_

pPO

INT2

8...

...R

......

......

......

......

.Del

ta T

empe

ratu

re (^

F)nv

oTEM

PDIF

F2...

......

......

......

SNVT

_tem

p_di

ff_p

POIN

T29

......

R...

......

......

......

....D

elta

Tem

pera

ture

(^F)

75

Figure A-12 GNRCMAP2 Table SNVTs and CPP Points

GNR

CMAP

2SN

VT T

ype

Rea

d or

Writ

e?

CPP

Poi

nt D

escr

iptio

nnv

iPCT

1....

......

......

......

......

......

SNVT

_lev

_per

cent

....P

OIN

T30

.....

W...

......

......

......

...Pe

rcen

t (%

)nv

iPCT

2....

......

......

......

......

......

SNVT

_lev

_per

cent

....P

OIN

T31

.....

W...

......

......

......

...Pe

rcen

t (%

)nv

oPCT

1...

......

......

......

......

.....

SNVT

_lev

_per

cent

....P

OIN

T32

.....

R...

......

......

......

....P

erce

nt (%

)nv

oPCT

2...

......

......

......

......

.....

SNVT

_lev

_per

cent

....P

OIN

T33

.....

R...

......

......

......

....P

erce

nt (%

)nv

oPCT

3...

......

......

......

......

.....

SNVT

_lev

_per

cent

....P

OIN

T34

.....

R...

......

......

......

....P

erce

nt (%

)nv

oPCT

4...

......

......

......

......

.....

SNVT

_lev

_per

cent

....P

OIN

T35

.....

R...

......

......

......

....P

erce

nt (%

)nv

iDIS

CR

ETE1

......

......

......

.....

SNVT

_sw

itch

......

.....

POIN

T36

.....

W...

......

......

......

...D

iscr

ete

(1/0

)nv

iDIS

CR

ETE2

......

......

......

.....

SNVT

_sw

itch

......

.....

POIN

T37

.....

W...

......

......

......

...D

iscr

ete

(1/0

)nv

iDIS

CR

ETE3

......

......

......

.....

SNVT

_sw

itch

......

.....

POIN

T38

.....

W...

......

......

......

...D

iscr

ete

(1/0

)nv

oDIS

CRET

E1...

......

......

......

.SN

VT_s

witc

h...

......

..PO

INT3

9...

..R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE2

......

......

......

....S

NVT

_sw

itch

......

.....

POIN

T40

.....

R...

......

......

......

....D

iscr

ete

(1/0

)nv

oDIS

CRET

E3...

......

......

......

.SN

VT_s

witc

h...

......

..PO

INT4

1...

..R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE4

......

......

......

....S

NVT

_sw

itch

......

.....

POIN

T42

.....

R...

......

......

......

....D

iscr

ete

(1/0

)nv

oDIS

CRET

E5...

......

......

......

.SN

VT_s

witc

h...

......

..PO

INT4

3...

..R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE6

......

......

......

....S

NVT

_sw

itch

......

.....

POIN

T44

.....

R...

......

......

......

....D

iscr

ete

(1/0

)nv

oDIS

CRET

E7...

......

......

......

.SN

VT_s

witc

h...

......

..PO

INT4

5...

..R

......

......

......

......

.Dis

cret

e (1

/0)

nvoD

ISCR

ETE8

......

......

......

....S

NVT

_sw

itch

......

.....

POIN

T46

.....

R...

......

......

......

....D

iscr

ete

(1/0

)nc

iSet

Pnts

.occ

upie

d_co

ol...

...SN

VT_t

emp_

setp

t....

POIN

T47

.....

W...

......

......

......

...Te

mpe

ratu

re S

etpo

int (

degF

)nc

iSet

Pnts

.sta

ndby

_coo

l....

...SN

VT_t

emp_

setp

t....

POIN

T48

.....

W...

......

......

......

...(N

A)nc

iSet

Pnts

.uno

cc_c

ool.

......

...SN

VT_t

emp_

setp

t....

POIN

T49

.....

W...

......

......

......

...Te

mpe

ratu

re S

etpo

int (

degF

)nc

iSet

Pnts

.occ

upie

d_he

at...

..SN

VT_t

emp_

setp

t....

POIN

T50

.....

W...

......

......

......

...Te

mpe

ratu

re S

etpo

int (

degF

)nc

iSet

Pnts

.sta

ndby

_hea

t....

...SN

VT_t

emp_

setp

t....

POIN

T51

.....

W...

......

......

......

...(N

A)nc

iSet

Pnts

.uno

cc_h

eat.

......

...SN

VT_t

emp_

setp

t....

POIN

T52

.....

W...

......

......

......

...Te

mpe

ratu

re S

etpo

int (

degF

)nv

iPPM

......

......

......

......

......

....S

NVT

_ppm

......

......

...PO

INT5

3...

..W

......

......

......

......

IAQ

(PPM

)nv

oPPM

......

......

......

......

......

...SN

VT_p

pm...

......

......

POIN

T54

.....

R...

......

......

......

....I

AQ (P

PM)

nviC

OUN

T1...

......

......

......

......

.SN

VT_c

ount

......

......

.PO

INT5

5...

..W

......

......

......

......

Gen

eric

ana

log

or d

iscr

ete

(0-6

5535

)nv

oCO

UNT1

......

......

......

......

...SN

VT_c

ount

......

......

.PO

INT5

6...

..R

......

......

......

......

.Gen

eric

ana

log

or d

iscr

ete

(0-6

5535

)nv

oCO

UNT2

......

......

......

......

...SN

VT_c

ount

......

......

.PO

INT5

7...

..R

......

......

......

......

.Gen

eric

ana

log

or d

iscr

ete

(0-6

5535

)nv

oCO

UNTi

nc1

......

......

......

.....

SNVT

_cou

nt_i

nc...

...PO

INT5

8...

..R

......

......

......

......

.Gen

eric

ana

log

or d

iscr

ete

(-327

67 - 3

2767

)nv

oCO

UNTi

nc2

......

......

......

.....

SNVT

_cou

nt_i

nc...

...PO

INT5

9...

..R

......

......

......

......

.Gen

eric

ana

log

or d

iscr

ete

(-327

67 - 3

2767

)

77

Index

AAddress and Baud Rate 5

BBaud Rate and Address 5

CChiller Maintenance Table 1 45Chiller Maintenance Table 2 48Chiller Mapping Table 1 16Chiller Mapping Table 2 21Chiller Template

points in 4CHLRMAP1 Table 16CHLRMAP2 Table 21CHLRMNT1 Table 45CHLRMNT2 Table 48Commissioning

on the LonWorks Network 12COMMSTAT Table 59Communication Status Maintenance

Table 59CONFIG Table 13Configuration

procedure for 9Configuration Table 13Configuration Tables 9

EErrors

mapping 11

GGeneric Maintenance Table 1 55Generic Maintenance Table 2 57Generic Mapping Table 1 36Generic Mapping Table 2 40Generic Template

points in 5GNRCMAP1 Table 36GNRCMAP2 Table 40GNRCMNT1 Table 55GNRCMNT2 Table 57

LLED Indicators 5

MMaintenance Tables 45Mapping Errors 11Messages Maintenance Table 61MESSAGES Table 61

RRooftop Maintenance Table 2 52Rooftop Template

points in 4RTUMNT1 Table 50RTUMNT2 Table 52

808 - 335 Rev. 06/16

lonworks ciat translator

Documents