iso/tc 23 - traktori i mašine za poljoprivredu i šumarstvo · iso/tc 23 - traktori i mašine za...
TRANSCRIPT
ISO/TC 23 - Traktori i mašine za poljoprivredu i šumarstvo
Spisak ažuriran 31.12.2008. godine
ISO/TC 23 – Tractors and machinery for agriculture and foresty
Standard and/or project TC
ISO 500-1:2004Agricultural tractors -- Rear-mounted power take-off types 1, 2 and 3 -- Part 1: General specifications, safety requirements, dimensions for master shield and clearance zone
TC 23/SC 4
ISO 500-1:2004/Cor 1:2005 TC 23/SC 4
ISO 500-2:2004Agricultural tractors -- Rear-mounted power take-off types 1, 2 and 3 -- Part 2: Narrow-track tractors, dimensions for master shield and clearance zone
TC 23/SC 4
ISO 500-3:2004Agricultural tractors -- Rear-mounted power take-off types 1, 2 and 3 -- Part 3: Main PTO dimensions and spline dimensions, location of PTO
TC 23/SC 4
ISO 730-1:1994Agricultural wheeled tractors -- Rear-mounted three-point linkage -- Part 1: Categories 1, 2, 3 and 4
TC 23/SC 4
ISO 730-1:1994/Cor 1:1995 TC 23/SC 4
ISO 730-2:1979Agricultural wheeled tractors -- Three-point linkage -- Part 2: Category 1 N (Narrow hitch)
TC 23/SC 4
ISO 789-1:1990Agricultural tractors -- Test procedures -- Part 1: Power tests for power take-off
TC 23/SC 2
ISO 789-2:1993Agricultural tractors -- Test procedures -- Part 2: Rear three-point linkage lifting capacity
TC 23/SC 2
ISO 789-3:1993Agricultural tractors -- Test procedures -- Part 3: Turning and clearance diameters
TC 23/SC 2
ISO 789-4:1986Agricultural tractors -- Test procedures -- Part 4: Measurement of exhaust
TC 23/SC 2
Standard and/or project TC
smoke
ISO 789-5:1983Agricultural tractors -- Test procedures -- Part 5: Partial power PTO -- Non-mechanically transmitted power
TC 23/SC 2
ISO 789-6:1982Agricultural tractors -- Test procedures -- Part 6: Centre of gravity
TC 23/SC 2
ISO 789-6:1982/Amd 1:1996 TC 23/SC 2
ISO 789-7:1991Agricultural tractors -- Test procedures -- Part 7: Axle power determination
TC 23/SC 2
ISO 789-8:1991Agricultural tractors -- Test procedures -- Part 8: Engine air cleaner
TC 23/SC 2
ISO 789-9:1990Agricultural tractors -- Test procedures -- Part 9: Power tests for drawbar
TC 23/SC 2
ISO 789-9:1990/Amd 1:1993 TC 23/SC 2
ISO/OECD 789-10:2006Agricultural tractors -- Test procedures -- Part 10: Hydraulic power at tractor/implement interface
TC 23/SC 2
32ISO 789-11:1996Agricultural tractors -- Test procedures -- Part 11: Steering capability of wheeled tractors
TC 23/SC 2
ISO 789-12:2000Agricultural tractors -- Test procedures -- Part 12: Low temperature starting
TC 23/SC 2
ISO 2057:1981Agricultural tractors -- Remote control hydraulic cylinders for trailed implements
TC 23/SC 4
ISO 2332:1993Agricultural tractors and machinery -- Connection of implements via three-point linkage -- Clearance zone around implement
TC 23/SC 4
ISO 3339-0:1986Tractors and machinery for agriculture and forestry -- Classification and terminology -- Part 0: Classification system and classification
TC 23
ISO 3463:2006Tractors for agriculture and forestry -- Roll-over protective structures (ROPS) -- Dynamic test method and acceptance conditions
TC 23/SC 2
ISO 3600:1996Tractors, machinery for agriculture and forestry, powered lawn and garden equipment -- Operator's manuals -- Content and presentation
TC 23/SC 14
Standard and/or project TC
ISO 3767-1:1998Tractors, machinery for agriculture and forestry, powered lawn and garden equipment -- Symbols for operator controls and other displays -- Part 1: Common symbols
TC 23/SC 14
ISO 3767-1:1998/Amd 1:2008Additional symbols
TC 23/SC 14
ISO 3767-2:2008Tractors, machinery for agriculture and forestry, powered lawn and garden equipment -- Symbols for operator controls and other displays -- Part 2: Symbols for agricultural tractors and machinery
TC 23/SC 14
ISO 3767-3:1995Tractors, machinery for agriculture and forestry, powered lawn and garden equipment -- Symbols for operator controls and other displays -- Part 3: Symbols for powered lawn and garden equipment
TC 23/SC 14
ISO 3767-4:1993Tractors, machinery for agriculture and forestry, powered lawn and garden equipment -- Symbols for operator controls and other displays -- Part 4: Symbols for forestry machinery
TC 23/SC 14
ISO 3767-4:1993/Amd 1:2000Additional symbols
TC 23/SC 14
ISO 3767-4:1993/Amd 2:2008Additional symbols
TC 23/SC 14
ISO 3767-5:1992Tractors, machinery for agriculture and forestry, powered lawn and garden equipment -- Symbols for operator controls and other displays -- Part 5: Symbols for manual portable forestry machinery
TC 23/SC 14
ISO 3767-5:1992/Amd 1:2001Revised and additional symbols
TC 23/SC 14
ISO 3776-1:2006Tractors and machinery for agriculture -- Seat belts -- Part 1: Anchorage location requirements
TC 23/SC 3
ISO 3776-2:2007Tractors and machinery for agriculture -- Seat belts -- Part 2: Anchorage strength requirements
TC 23/SC 2
ISO 3835-1:1976Equipment for vine cultivation and wine making -- Vocabulary
TC 23
ISO 3835-2:1977Equipment for vine cultivation and wine making -- Vocabulary
TC 23
ISO 3835-3:1980Equipment for vine cultivation and wine making -- Vocabulary
TC 23
Standard and/or project TC
ISO 3835-4:1981Equipment for vine cultivation and wine making -- Vocabulary
TC 23
ISO 3835-5:1982Equipment for vine cultivation and wine making -- Vocabulary
TC 23
ISO 3918:2007Milking machine installations -- Vocabulary
TC 23
ISO 3965:1990Agricultural wheeled tractors -- Maximum speeds -- Method of determination
TC 23/SC 2
ISO 4002-1:1979Equipment for sowing and planting -- Part 1: Concave disks type D1 -- Dimensions
TC 23
ISO 4002-2:1977Equipment for sowing and planting -- Disks -- Part 2: Flat disks type D2 with single bevel -- Dimensions
TC 23
ISO 4004:1983Agricultural tractors and machinery -- Track widths
TC 23/SC 4
ISO 4102:1984Equipment for crop protection -- Sprayers -- Connection threading
TC 23/SC 6
ISO 4197:1989Equipment for working the soil -- Hoe blades -- Fixing dimensions
TC 23
ISO 4252:2007Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
TC 23/SC 4
ISO 4253:1993Agricultural tractors -- Operator's seating accommodation -- Dimensions
TC 23/SC 4
ISO 4254-1:2008Agricultural machinery -- Safety -- Part 1: General requirements
TC 23/SC 3
ISO 4254-5:2008Agricultural machinery -- Safety -- Part 5: Power-driven soil-working machines
TC 23/SC 3
ISO 4254-6:1995Tractors and machinery for agriculture and forestry -- Technical means for ensuring safety -- Part 6: Equipment for crop protection
TC 23/SC 6
ISO 4254-7:2008Agricultural machinery -- Safety -- Part 7: Combine harvesters, forage harvesters and cotton harvesters
TC 23/SC 7
ISO 4254-9:2008Agricultural machinery -- Safety -- Part 9: Seed drills
TC 23/SC 3
Standard and/or project TC
ISO 5007:2003Agricultural wheeled tractors -- Operator's seat -- Laboratory measurement of transmitted vibration
TC 23/SC 2
ISO 5008:2002Agricultural wheeled tractors and field machinery -- Measurement of whole-body vibration of the operator
TC 23/SC 2
ISO 5008:2002/Cor 1:2005 TC 23/SC 2
ISO 5131:1996Acoustics -- Tractors and machinery for agriculture and forestry -- Measurement of noise at the operator's position -- Survey method
TC 23/SC 3
ISO 5395:1990Power lawn-mowers, lawn tractors, lawn and garden tractors, professional mowers, and lawn and garden tractors with mowing attachments -- Definitions, safety requirements and test procedures
TC 23/SC 13
ISO 5395:1990/Amd 1:1992 TC 23/SC 13
ISO 5669:1982Agricultural trailers and trailed equipment -- Braking cylinders -- Specifications
TC 23
ISO 5670:1984Agricultural trailers -- Single-acting telescopic tipping cylinders -- 25 MPa (250 bar) series -- Types 1, 2 and 3 -- Interchangeability dimensions
TC 23/SC 4
ISO 5673-1:2005Agricultural tractors and machinery -- Power take-off drive shafts and power-input connection -- Part 1: General manufacturing and safety requirements
TC 23/SC 4
ISO 5673-2:2005Agricultural tractors and machinery -- Power take-off drive shafts and power-input connection -- Part 2: Specification for use of PTO drive shafts, and position and clearance of PTO drive line and PIC for various attachments
TC 23/SC 4
ISO 5674:2004Tractors and machinery for agriculture and forestry -- Guards for power take-off (PTO) drive-shafts -- Strength and wear tests and acceptance criteria
TC 23/SC 2
ISO 5675:2008Agricultural tractors and machinery -- General purpose quick-action hydraulic couplers
TC 23/SC 4
ISO 5676:1983Tractors and machinery for agriculture and forestry -- Hydraulic coupling -- Braking circuit
TC 23/SC 4
Standard and/or project TC
ISO 5678:1993Agricultural machinery -- Equipment for working the soil -- S-tines: main dimensions and clearance zones
TC 23
ISO 5679:1979Equipment for working the soil -- Disks -- Classification, main fixing dimensions and specifications
TC 23
ISO 5680:1979Equipment for working soil -- Tines and shovels for cultivators -- Main fixing dimensions
TC 23
ISO 5681:1992Equipment for crop protection -- Vocabulary
TC 23/SC 6
ISO 5682-1:1996Equipment for crop protection -- Spraying equipment -- Part 1: Test methods for sprayer nozzles
TC 23/SC 6
ISO 5682-2:1997Equipment for crop protection -- Spraying equipment -- Part 2: Test methods for hydraulic sprayers
TC 23/SC 6
ISO 5682-3:1996Equipment for crop protection -- Spraying equipment -- Part 3: Test method for volume/hectare adjustment systems of agricultural hydraulic pressure sprayers
TC 23/SC 6
ISO 5687:1999Equipment for harvesting -- Combine harvesters -- Determination and designation of grain tank capacity and unloading device performance
TC 23/SC 7
ISO 5690-1:1985Equipment for distributing fertilizers -- Test methods -- Part 1: Full width fertilizer distributors
TC 23
ISO 5690-2:1984Equipment for distributing fertilizers -- Test methods -- Part 2: Fertilizer distributors in lines
TC 23
ISO 5691:1981Equipment for planting -- Potato planters -- Method of testing
TC 23
ISO 5692-1:2004Agricultural vehicles -- Mechanical connections on towed vehicles -- Part 1: Dimensions for hitch rings of 50/30 mm cross section
TC 23/SC 4
ISO 5692-2:2002Agricultural vehicles -- Mechanical connections on towed vehicles -- Part 2: Coupling ring 40 with socket
TC 23/SC 4
ISO 5692-2:2002/Cor 1:2004 TC 23/SC 4
Standard and/or project TC
ISO 5696:1984Trailed agricultural vehicles -- Brakes and braking devices -- Laboratory test method
TC 23/SC 2
ISO 5697:1982Agricultural and forestry vehicles -- Determination of braking performance
TC 23/SC 2
ISO 5699:1979Agricultural machines, implements and equipment -- Dimensions for mechanical loading with bulk goods
TC 23
ISO 5700:2006Tractors for agriculture and forestry -- Roll-over protective structures (ROPS) -- Static test method and acceptance conditions
TC 23/SC 2
ISO 5702:1983Equipment for harvesting -- Combine harvester component parts -- Equivalent terms
TC 23/SC 7
ISO 5703:1979Equipment for vine cultivation and wine making -- Grape presses -- Methods of test
TC 23
ISO 5704:1980Equipment for vine cultivation and wine making -- Grape-harvesting machinery -- Test methods
TC 23
ISO 5707:2007Milking machine installations -- Construction and performance
TC 23
ISO 5708:1983Refrigerated bulk milk tanks
TC 23
ISO 5710:1980Equipment for internal farm work and husbandry -- Continuous manure scraper conveyors for stalls
TC 23
ISO 5711:1995Tractors and machinery for agriculture and forestry -- Wheel-to-hub fixing dimensions
TC 23/SC 4
ISO 5713:1990Equipment for working the soil -- Fixing bolts for soil working elements
TC 23
ISO 5715:1983Equipment for harvesting -- Dimensional compatibility of forage harvesting machinery
TC 23/SC 7
ISO 5718:2002Harvesting equipment -- Blades for agricultural rotary mowers -- Requirements
TC 23/SC 7
ISO 5721:1989 TC 23/SC 4
Standard and/or project TC
Tractors for agriculture -- Operator's field of vision
ISO 6489-1:2001Agricultural vehicles -- Mechanical connections between towed and towing vehicles -- Part 1: Dimensions of hitch-hooks
TC 23/SC 4
ISO 6489-2:2002Agricultural vehicles -- Mechanical connections between towed and towing vehicles -- Part 2: Specifications for clevis coupling 40
TC 23/SC 4
ISO 6489-3:2004Agricultural vehicles -- Mechanical connections between towed and towing vehicles -- Part 3: Tractor drawbar
TC 23/SC 4
ISO 6489-4:2004Agricultural vehicles -- Mechanical connections between towed and towing vehicles -- Part 4: Dimensions of piton-type coupling
TC 23/SC 4
ISO 6531:2008Machinery for forestry -- Portable chain-saws -- Vocabulary
TC 23/SC 17
ISO 6533:2001Forestry machinery -- Portable chain-saw front hand-guard -- Dimensions and clearances
TC 23/SC 17
ISO 6534:2007Forestry machinery -- Portable chain-saw hand-guards -- Mechanical strength
TC 23/SC 17
ISO 6535:2008Portable chain-saws -- Chain brake performance
TC 23/SC 17
ISO 6686:1995Equipment for crop protection -- Antidrip devices -- Determination of performance
TC 23/SC 6
ISO 6689-1:1997Equipment for harvesting -- Combines and functional components -- Part 1: Vocabulary
TC 23/SC 7
ISO 6689-2:1997Equipment for harvesting -- Combines and functional components -- Part 2: Assessment of characteristics and performance defined in vocabulary
TC 23/SC 7
ISO 6690:2007Milking machine installations -- Mechanical tests
TC 23
ISO 6720:1989Agricultural machinery -- Equipment for sowing, planting, distributing fertilizers and spraying -- Recommended working widths
TC 23
ISO 6814:2000Machinery for forestry -- Mobile and self-propelled machinery -- Terms,
TC 23/SC 15
Standard and/or project TC
definitions and classification
ISO 6880:1983Machinery for agriculture -- Trailed units of shallow tillage equipment -- Main dimensions and attachment points
TC 23
ISO 7072:1993Tractors and machinery for agriculture and forestry -- Linch pins and spring pins -- Dimensions and requirements
TC 23/SC 4
ISO 7112:2008Machinery for forestry -- Portable brush-cutters and grass-trimmers -- Vocabulary
TC 23/SC 17
ISO 7113:1999Portable hand-held forestry machines -- Cutting attachments for brush cutters -- Single-piece metal blades
TC 23/SC 17
ISO 7216:1992Acoustics -- Agricultural and forestry wheeled tractors and self-propelled machines -- Measurement of noise emitted when in motion
TC 23/SC 2
ISO 7224:1983Equipment for vine cultivation and wine making -- Mash pumps -- Methods of test
TC 23
ISO 7256-1:1984Sowing equipment -- Test methods -- Part 1: Single seed drills (precision drills)
TC 23
ISO 7256-2:1984Sowing equipment -- Test methods -- Part 2: Seed drills for sowing in lines
TC 23
ISO 7293:1997Forestry machinery -- Portable chain saws -- Engine performance and fuel consumption
TC 23/SC 17
ISO 7714:2008Agricultural irrigation equipment -- Volumetric valves -- General requirements and test methods
TC 23/SC 18
ISO 7749-1:1995Agricultural irrigation equipment -- Rotating sprinklers -- Part 1: Design and operational requirements
TC 23/SC 18
ISO 7914:2002Forestry machinery -- Portable chain-saws -- Minimum handle clearance and sizes
TC 23/SC 17
ISO 7915:1991Forestry machinery -- Portable chain-saws -- Determination of handle strength
TC 23/SC 17
Standard and/or project TC
ISO 7918:1995Forestry machinery -- Portable brush-cutters and grass-trimmers -- Cutting attachment guard dimensions
TC 23/SC 17
ISO 8016:1985Machinery for agriculture -- Wheels with integral hub
TC 23
ISO 8026:1995Agricultural irrigation equipment -- Sprayers -- General requirements and test methods
TC 23/SC 18
ISO 8026:1995/Amd 1:2000 TC 23/SC 18
ISO/TR 8059:1986Irrigation equipment -- Automatic irrigation systems -- Hydraulic control
TC 23/SC 18
ISO 8082:2003Self-propelled machinery for forestry -- Roll-over protective structures -- Laboratory tests and performance requirements
TC 23/SC 15
ISO 8083:2006Machinery for forestry -- Falling-object protective structures (FOPS) -- Laboratory tests and performance requirements
TC 23/SC 15
ISO 8084:2003Machinery for forestry -- Operator protective structures -- Laboratory tests and performance requirements
TC 23/SC 15
ISO 8088:1994Equipment for olive cultivation and olive oil production -- Vocabulary
TC 23
ISO 8169:1984Equipment for crop protection -- Sprayers -- Connecting dimensions for nozzles and manometers
TC 23/SC 6
ISO 8210:1989Equipment for harvesting -- Combine harvesters -- Test procedure
TC 23/SC 7
ISO 8224-1:2003Traveller irrigation machines -- Part 1: Operational characteristics and laboratory and field test methods
TC 23/SC 18
ISO 8224-2:1991Traveller irrigation machines -- Part 2: Softwall hose and couplings -- Test methods
TC 23/SC 18
ISO 8334:2007Forestry machinery -- Portable chain-saws -- Determination of balance and maximum holding moment
TC 23/SC 17
ISO 8380:1993Forestry machinery -- Portable brush-cutters and grass-trimmers -- Cutting attachment guard strength
TC 23/SC 17
Standard and/or project TC
ISO 8437:1989Snowthrowers -- Safety requirements and test procedures
TC 23/SC 13
ISO 8437:1989/Amd 1:1997 TC 23/SC 13
ISO 8524:1986Equipment for distributing granulated pesticides or herbicides -- Test method
TC 23/SC 6
ISO 8759-1:1998Agricultural wheeled tractors -- Front-mounted equipment -- Part 1: Power take-off and three- point linkage
TC 23/SC 4
ISO 8759-2:1998Agricultural wheeled tractors -- Front-mounted equipment -- Part 2: Stationary equipment connection
TC 23/SC 4
ISO 8893:1997Forestry machinery -- Portable brush-cutters and grass-trimmers -- Engine performance and fuel consumption
TC 23/SC 17
ISO 8909-1:1994Forage harvesters -- Part 1: Vocabulary
TC 23/SC 7
ISO 8909-2:1994Forage harvesters -- Part 2: Specification of characteristics and performance
TC 23/SC 7
ISO 8909-3:1994Forage harvesters -- Part 3: Test methods
TC 23/SC 7
ISO 8910:1993Machinery and equipment for working the soil -- Mouldboard plough working elements -- Vocabulary
TC 23
ISO 8912:1986Equipment for working the soil -- Roller sections -- Coupling and section width
TC 23
ISO 8935:1990Tractors for agriculture and forestry -- Mountings and apertures for external equipment controls
TC 23/SC 4
ISO 8945:1989Equipment for working the soil -- Rotary cultivator blades -- Fixing dimensions
TC 23
ISO 8947:1993Agricultural machinery -- Equipment for working the soil -- S-tines: test method
TC 23
ISO 9191:1991Lawn and garden ride-on (riding) tractors -- Three-point hitch
TC 23/SC 13
Standard and/or project TC
ISO 9192:1991Lawn and garden ride-on (riding) tractors -- One-point tubular sleeve hitch
TC 23/SC 13
ISO 9261:2004Agricultural irrigation equipment -- Emitters and emitting pipe -- Specification and test methods
TC 23/SC 18
ISO 9357:1990Equipment for crop protection -- Agricultural sprayers -- Tank nominal volume and filling hole diameter
TC 23/SC 6
ISO 9467:1993Forestry machinery -- Portable chain-saws and brush-cutters -- Exhaust system-caused fire risk
TC 23/SC 17
ISO 9518:1998Forestry machinery -- Portable chain-saws -- Kickback test
TC 23/SC 17
ISO 9635-1:2006Agricultural irrigation equipment -- Irrigation valves -- Part 1: General requirements
TC 23/SC 18
ISO 9635-2:2006Agricultural irrigation equipment -- Irrigation valves -- Part 2: Isolating valves
TC 23/SC 18
ISO 9635-3:2006Agricultural irrigation equipment -- Irrigation valves -- Part 3: Check valves
TC 23/SC 18
ISO 9635-4:2006Agricultural irrigation equipment -- Irrigation valves -- Part 4: Air valves
TC 23/SC 18
ISO 9635-5:2006Agricultural irrigation equipment -- Irrigation valves -- Part 5: Control valves
TC 23/SC 18
ISO 9644:2008Agricultural irrigation equipment -- Pressure losses in irrigation valves -- Test method
TC 23/SC 18
ISO 9898:2000Equipment for crop protection -- Test methods for air-assisted sprayers for bush and tree crops
TC 23/SC 6
ISO 9911:2006Agricultural irrigation equipment -- Manually operated small plastics valves
TC 23/SC 18
ISO 9912-1:2004Agricultural irrigation equipment -- Filters for micro-irrigation -- Part 1: Terms, definitions and classification
TC 23/SC 18
Standard and/or project TC
ISO 9912-2:1992Agricultural irrigation equipment -- Filters -- Part 2: Strainer-type filters
TC 23/SC 18
ISO 9912-3:1992Agricultural irrigation equipment -- Filters -- Part 3: Automatic self-cleaning strainer-type filters
TC 23/SC 18
ISO 10448:1994Agricultural tractors -- Hydraulic pressure for implements
TC 23/SC 4
ISO 10517:1993Portable powered hedge trimmers -- Definitions, mechanical safety requirements and tests
TC 23/SC 13
ISO 10522:1993Agricultural irrigation equipment -- Direct-acting pressure-regulating valves
TC 23/SC 18
ISO 10625:2005Equipment for crop protection -- Sprayer nozzles -- Colour coding for identification
TC 23/SC 6
ISO 10626:1991Equipment for crop protection -- Sprayers -- Connecting dimensions for nozzles with bayonet fixing
TC 23/SC 6
ISO 10627-1:1992Agricultural sprayers -- Data sheet -- Part 1: Typical layout
TC 23/SC 6
ISO 10627-2:1996Hydraulic agricultural sprayers -- Data sheets -- Part 2: Technical specifications related to components
TC 23/SC 6
ISO 10726:1992Portable chain saws -- Chain catcher -- Dimensions and mechanical strength
TC 23/SC 17
ISO 10998:2008Agricultural tractors -- Requirements for steering
TC 23/SC 4
ISO 11001-1:1993Agricultural wheeled tractors and implements -- Three-point hitch couplers -- Part 1: U-frame coupler
TC 23/SC 4
ISO 11001-2:1993Agricultural wheeled tractors and implements -- Three-point hitch couplers -- Part 2: A-frame coupler
TC 23/SC 4
ISO 11001-3:1993Agricultural wheeled tractors and implements -- Three-point hitch couplers -- Part 3: Link coupler
TC 23/SC 4
ISO 11001-4:1994 TC 23/SC 4
Standard and/or project TC
Agricultural wheeled tractors and implements -- Three-point hitch couplers -- Part 4: Bar coupler
ISO 11169:1993Machinery for forestry -- Wheeled special machines -- Vocabulary, performance test methods and criteria for brake systems
TC 23/SC 15
ISO 11448:1997Powered shredders and chippers -- Definitions, safety requirements and test procedures
TC 23/SC 13
ISO 11449:1994Walk-behind powered rotary tillers -- Definitions, safety requirements and test procedures
TC 23/SC 13
ISO 11450:1999Equipment for harvesting and conservation -- Round balers -- Terminology and commercial specifications
TC 23/SC 7
ISO 11471:1995Agricultural tractors and machinery -- Coding of remote hydraulic power services and controls
TC 23/SC 4
ISO 11512:1995Machinery for forestry -- Tracked special machines -- Performance criteria for brake systems
TC 23/SC 15
ISO 11520-1:1997Agricultural grain driers -- Determination of drying performance -- Part 1: General
TC 23/SC 7
ISO 11520-2:2001Agricultural grain driers -- Determination of drying performance -- Part 2: Additional procedures and crop-specific requirements
TC 23/SC 7
ISO 11545:2001Agricultural irrigation equipment -- Centre-pivot and moving lateral irrigation machines with sprayer or sprinkler nozzles -- Determination of uniformity of water distribution
TC 23/SC 18
ISO 11678:1996Agricultural irrigation equipment -- Aluminium irrigation tubes
TC 23/SC 18
ISO 11680-1:2000Machinery for forestry -- Safety requirements and testing for pole-mounted powered pruners -- Part 1: Units fitted with an integral combustion engine
TC 23/SC 17
ISO 11680-2:2000Machinery for forestry -- Safety requirements and testing for pole-mounted powered pruners -- Part 2: Units for use with a back-pack power source
TC 23/SC 17
ISO 11681-1:2004Machinery for forestry -- Portable chain-saw safety requirements and
TC 23/SC 17
Standard and/or project TC
testing -- Part 1: Chain-saws for forest service
ISO 11681-1:2004/Amd 1:2007Balance
TC 23/SC 17
ISO 11681-2:2006Machinery for forestry -- Portable chain-saw safety requirements and testing -- Part 2: Chain-saws for tree service
TC 23/SC 17
ISO 11684:1995Tractors, machinery for agriculture and forestry, powered lawn and garden equipment -- Safety signs and hazard pictorials -- General principles
TC 23/SC 14
ISO 11738:2000Agricultural irrigation equipment -- Control heads
TC 23/SC 18
ISO 11783-1:2007Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 1: General standard for mobile data communication
TC 23/SC 19
ISO 11783-2:2002Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 2: Physical layer
TC 23/SC 19
ISO 11783-2:2002/Amd 1:2006 TC 23/SC 19
ISO 11783-2:2002/Cor 1:2003 TC 23/SC 19
ISO 11783-3:2007Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 3: Data link layer
TC 23/SC 19
ISO 11783-4:2001Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 4: Network layer
TC 23/SC 19
ISO 11783-5:2001Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 5: Network management
TC 23/SC 19
ISO 11783-5:2001/Cor 1:2002 TC 23/SC 19
ISO 11783-6:2004Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 6: Virtual terminal
TC 23/SC 19
ISO 11783-6:2004/Cor 1:2005 TC 23/SC 19
ISO 11783-7:2002Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 7: Implement messages application
TC 23/SC 19
Standard and/or project TC
layer
ISO 11783-7:2002/Cor 1:2004 TC 23/SC 19
ISO 11783-8:2006Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 8: Power train messages
TC 23/SC 19
ISO 11783-9:2002Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 9: Tractor ECU
TC 23/SC 19
ISO 11783-11:2007Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 11: Mobile data element dictionary
TC 23/SC 19
ISO 11783-13:2007Tractors and machinery for agriculture and forestry -- Serial control and communications data network -- Part 13: File server
TC 23/SC 19
ISO 11784:1996Radio frequency identification of animals -- Code structure
TC 23/SC 19
ISO 11784:1996/Amd 1:2004 TC 23/SC 19
ISO 11785:1996Radio frequency identification of animals -- Technical concept
TC 23/SC 19
ISO 11786:1995Agricultural tractors and machinery -- Tractor-mounted sensor interface -- Specifications
TC 23/SC 19
ISO 11787:1995Machinery for agriculture and forestry -- Data interchange between management computer and process computers -- Data interchange syntax
TC 23/SC 19
ISO 11788-1:1997Electronic data interchange between information systems in agriculture -- Agricultural data element dictionary -- Part 1: General description
TC 23/SC 19
ISO 11788-2:2000Electronic data interchange between information systems in agriculture -- Agricultural data element dictionary -- Part 2: Dairy farming
TC 23/SC 19
ISO 11788-3:2000Electronic data interchange between information systems in agriculture -- Agricultural data element dictionary -- Part 3: Pig farming
TC 23/SC 19
ISO 11789:1999Powered edgers with rigid cutting means -- Definitions, safety requirements and test procedures
TC 23/SC 13
ISO 11806:1997 TC 23/SC 17
Standard and/or project TC
Agricultural and forestry machinery -- Portable hand-held combustion engine driven brush cutters and grass trimmers -- Safety
ISO 11850:2003Machinery for forestry -- Self-propelled machinery -- Safety requirements
TC 23/SC 15
ISO 12003-1:2008Agricultural and forestry tractors -- Roll-over protective structures on narrow-track wheeled tractors -- Part 1: Front-mounted ROPS
TC 23/SC 2
ISO 12003-2:2008Agricultural and forestry tractors -- Roll-over protective structures on narrow-track wheeled tractors -- Part 2: Rear-mounted ROPS
TC 23/SC 2
ISO 12140:1998Agricultural machinery -- Agricultural trailers and trailed equipment -- Drawbar jacks
TC 23/SC 3
ISO 12368:2001Agricultural vehicles -- Mechanical hook-type connections on towing vehicles -- Test methods and requirements
TC 23/SC 2
ISO/TR 12369:1994Agricultural tractors and machinery -- Electrical power transmission connectors
TC 23/SC 4
ISO/TR 12369:1994/Amd 1:1999 TC 23/SC 4
ISO 12374:1995Agricultural irrigation -- Wiring and equipment for electrically driven or controlled irrigation machines
TC 23/SC 18
ISO 13440:1996Equipment for crop protection -- Agricultural sprayers -- Determination of the volume of total residual
TC 23/SC 6
ISO 13441-1:1997Air-assisted agricultural sprayers -- Data sheets -- Part 1: Typical layout
TC 23/SC 6
ISO 13441-2:1997Air-assisted agricultural sprayers -- Data sheets -- Part 2: Technical specifications related to components
TC 23/SC 6
ISO 13457:2008Agricultural irrigation equipment -- Water-driven chemical injector pumps
TC 23/SC 18
ISO 13460:1998Agricultural irrigation equipment -- Plastics saddles for polyethylene pressure pipes
TC 23/SC 18
ISO 13772:2004Forestry machinery -- Portable chain-saws -- Non-manually actuated chain brake performance
TC 23/SC 17
Standard and/or project TC
ISO 13860:2000Machinery for forestry -- Forwarders -- Terms, definitions and commercial specifications
TC 23/SC 15
ISO 13861:2000Machinery for forestry -- Wheeled skidders -- Terms, definitions and commercial specifications
TC 23/SC 15
ISO 13862:2000Machinery for forestry -- Feller-bunchers -- Terms, definitions and commercial specifications
TC 23/SC 15
ISO 14131:2005Agricultural sprayers -- Boom steadiness -- Test methods
TC 23/SC 6
ISO 14223-1:2003Radiofrequency identification of animals -- Advanced transponders -- Part 1: Air interface
TC 23/SC 19
ISO 14269-1:1997Tractors and self-propelled machines for agriculture and forestry -- Operator enclosure environment -- Part 1: Vocabulary
TC 23/SC 2
ISO 14269-2:1997Tractors and self-propelled machines for agriculture and forestry -- Operator enclosure environment -- Part 2: Heating, ventilation and air-conditioning test method and performance
TC 23/SC 2
ISO 14269-3:1997Tractors and self-propelled machines for agriculture and forestry -- Operator enclosure environment -- Part 3: Determination of effect of solar heating
TC 23/SC 2
ISO 14269-4:1997Tractors and self-propelled machines for agriculture and forestry -- Operator enclosure environment -- Part 4: Air filter element test method
TC 23/SC 2
ISO 14269-5:1997Tractors and self-propelled machines for agriculture and forestry -- Operator enclosure environment -- Part 5: Pressurization system test method
TC 23/SC 2
ISO 14710:1996Equipment for crop protection -- Air-assisted sprayers -- Dimensions of nozzle swivel nuts
TC 23/SC 6
ISO 14740:1998Forest machinery -- Backpack power units for brush-cutters, grass-trimmers, pole-cutters and similar appliances -- Safety requirements and testing
TC 23/SC 17
ISO 14865:1998 TC 23/SC 17
Standard and/or project TC
Machinery for forestry -- Portable hand-held brush-cutters and grass-trimmers with backpack-mounted combustion-engine power source -- Safety requirements and testing
ISO 14982:1998Agricultural and forestry machinery -- Electromagnetic compatibility -- Test methods and acceptance criteria
TC 23/SC 2
ISO 15003:2006Agricultural engineering -- Electrical and electronic equipment -- Testing resistance to environmental conditions
TC 23/SC 19
ISO 15077:2008Tractors and self-propelled machinery for agriculture -- Operator controls -- Actuating forces, displacement, location and method of operation
TC 23/SC 3
ISO 15078:1998Machinery for forestry -- Log loaders -- Location and method of operation of two-lever operator controls
TC 23/SC 15
ISO/TS 15079:2001Powered lawn, garden and horticultural equipment -- Operator controls -- Guidance on actuating forces, displacement, location and methods of operation
TC 23/SC 13
ISO 15081:2005Agricultural irrigation equipment -- Graphical symbols for pressurized irrigation systems
TC 23/SC 18
ISO/TR 15155:2005Test facilities for agricultural irrigation equipment
TC 23/SC 18
ISO 15873:2002Irrigation equipment -- Differential pressure Venturi-type liquid additive injectors
TC 23/SC 18
ISO 15886-1:2004Agricultural irrigation equipment -- Sprinklers -- Part 1: Definition of terms and classification
TC 23/SC 18
ISO 15886-3:2004Agricultural irrigation equipment -- Sprinklers -- Part 3: Characterization of distribution and test methods
TC 23/SC 18
ISO 16149:2006Agricultural irrigation equipment -- PVC above-ground low-pressure pipe for surface irrigation -- Specifications and test methods
TC 23/SC 18
ISO 16154:2005Tractors and machinery for agriculture and forestry -- Installation of lighting, light signalling and marking devices for travel on public roadways
TC 23/SC 4
ISO 17080:2005 TC 23/SC 14
Standard and/or project TC
Manually portable agricultural and forestry machines and powered lawn and garden equipment -- Design principles for single-panel product safety labels
ISO 17101:2004Agricultural machinery -- Rotary and flail mowers -- Thrown-object test and acceptance criteria
TC 23/SC 7
ISO 17103:2003Agricultural machinery -- Rotary and flail mowers -- Test methods and acceptance criteria for protective skirts
TC 23/SC 7
ISO 17314:2008Manually portable forest machinery -- Recyclability and recoverability -- Calculation method
TC 23/SC 17
ISO 17532:2007Stationary equipment for agriculture -- Data communications network for livestock farming
TC 23/SC 19
ISO 17567:2005Agricultural and forestry tractors and implements -- Hydraulic power beyond
TC 23/SC 4
ISO 17591:2002Machinery for forestry -- Knuckleboom log loaders -- Identification terminology, classification and component nomenclature
TC 23/SC 15
ISO 17612:2004Tractors and machinery for agriculture and forestry -- Auxiliary-power-transmission connector for the operator station
TC 23/SC 4
ISO 17900:2002Agricultural trailers -- Balanced and semi-mounted trailers -- Determination of payload, vertical static load and axle load
TC 23/SC 4
ISO 19472:2006Machinery for forestry -- Winches -- Dimensions, performance and safety
TC 23/SC 15
ISO 19472:2006/Cor 1:2006 TC 23/SC 15
ISO 19732:2007Equipment for crop protection -- Sprayer filters -- Colour coding for identification
TC 23/SC 6
ISO 19932-1:2006Equipment for crop protection -- Knapsack sprayers -- Part 1: Requirements and test methods
TC 23/SC 6
ISO 19932-2:2006Equipment for crop protection -- Knapsack sprayers -- Part 2: Performance limits
TC 23/SC 6
Standard and/or project TC
ISO 20019:2001Agricultural vehicles -- Mechanical connections on towed vehicles -- Dimensions for hitch rings
TC 23/SC 4
ISO 20019:2001/Cor 1:2004 TC 23/SC 4
ISO 20966:2007Automatic milking installations -- Requirements and testing
TC 23
ISO 21244:2008Agricultural equipment -- Mechanical connections between towed and towing vehicles -- Implement hitch rings and attachment to tractor drawbars
TC 23/SC 4
ISO 21278-1:2008Equipment for crop protection -- Induction hoppers -- Part 1: Test methods
TC 23/SC 6
ISO 21278-2:2008Equipment for crop protection -- Induction hoppers -- Part 2: General requirements and performance limits
TC 23/SC 6
ISO 21628:2008Gardening machinery -- Powered material-collecting systems -- Safety
TC 23/SC 13
ISO 22368-1:2004Crop protection equipment -- Test methods for the evaluation of cleaning systems -- Part 1: Internal cleaning of complete sprayers
TC 23/SC 6
ISO 22368-2:2004Crop protection equipment -- Test methods for the evaluation of cleaning systems -- Part 2: External cleaning of sprayers
TC 23/SC 6
ISO 22368-3:2004Crop protection equipment -- Test methods for the evaluation of cleaning systems -- Part 3: Internal cleaning of tank
TC 23/SC 6
ISO 22369-1:2006Crop protection equipment -- Drift classification of spraying equipment -- Part 1: Classes
TC 23/SC 6
ISO/TR 22520:2005Portable hand-held forestry machines -- A-weighted emission sound pressure levels at the operator's station -- Comparative data in 2002
TC 23/SC 17
ISO/TR 22521:2005Portable hand-held forestry machines -- Vibration emission values at the handles -- Comparative data in 2002
TC 23/SC 17
ISO 22522:2007Crop protection equipment -- Field measurement of spray distribution in tree and bush crops
TC 23/SC 6
ISO 22763:2006 TC 23/SC 6
Standard and/or project TC
Equipment for crop protection -- Sprayers -- Demonstration track for field crop sprayers
ISO 22856:2008Equipment for crop protection -- Methods for the laboratory measurement of spray drift -- Wind tunnels
TC 23/SC 6
ISO 22866:2005Equipment for crop protection -- Methods for field measurement of spray drift
TC 23/SC 6
ISO 22867:2004Forestry machinery -- Vibration test code for portable hand-held machines with internal combustion engine -- Vibration at the handles
TC 23/SC 17
ISO 22867:2004/Cor 1:2006 TC 23/SC 17
ISO 22868:2005Forestry machinery -- Noise test code for portable hand-held machines with internal combustion engine -- Engineering method (Grade 2 accuracy)
TC 23/SC 17
ISO 23205:2006Agricultural tractors -- Instructional seat
TC 23/SC 4
ISO 23206:2005Agricultural wheeled tractors and attachments -- Front loaders -- Carriages for attachments
TC 23/SC 4
ISO 23206:2005/Cor 1:2007 TC 23/SC 4
ISO 24347:2005Agricultural vehicles -- Mechanical connections between towed and towing vehicles -- Dimensions of ball-type coupling device (80 mm)
TC 23/SC 4
ISO 26322-1:2008Tractors for agriculture and forestry -- Safety -- Part 1: Standard tractors
TC 23/SC 4
ISO 26402:2008Agricultural vehicles -- Steering systems for agricultural trailers -- Interface for articulated steering device of semi-mounted trailers
TC 23/SC 4
ISO/TS 28923:2007Agricultural machinery - Guards for moving parts of power transmission - Guard opening with tool
TC 23/SC 3
ISO/TS 28924:2007Agricultural machinery - Guards for moving parts of power transmission - Guard opening without tool
TC 23/SC 3