www.kufatec.de

Kufatec GmbH & Co. KG • Dahlienstr. 15 • 23795 Bad Segeberg • e-mail: info@kufatec.de

Version 1.02

(25.07.2014)

Installation instruction

Rear view camera

Article no.: 37169

37170

Audi Q7 4L – MMI 3G

1

ContentsGeneral advice .........................................................................................................................................1

Safety instructions ....................................................................................................................................2

References of legal regulations for operation ...........................................................................................2

Rear view camera ....................................................................................................................................3

Scope of delivery......................................................................................................................................3

Installation instructions .............................................................................................................................4

CAN wire connection................................................................................................................................7

Coding......................................................................................................................................................9

General adviceWhile developing this product, your personal safety combined with the best operating service, moderndesign and an up-to-date production technique was especially taken into account.

Unfortunately, despite the utmost care injuries and/or damages might occur due to improper installationand/or use.

Therefore please read with great care and completely this operating manual and store it appropriately!

For your safety all our products pass through a 100% control check.

We reserve the right to carry out technical changes which serve the improvement at any time.

According to each article and purpose, it is sometimes necessary to check each country’s legalregulations before installing and starting the unit.

In case of guarantee claims, the device has to be sent back to the seller in the original packaging withthe attached bill of purchase and detailed defect‘s description. Please pay attention to the manufacturer‘sreturn requirements (RMA). The legal warranty directions are valid.

The warranty claims as well as the operating permissions become invalid due to:

a) unauthorized changes to the device or accessories which have not been approved or carriedout by the manufacturer or its partners

b) opening the device‘s frame

c) self-made repairs on the device

d) improper use / operation

e) brute force to the device (drop, willful damage, accident etc.)

During installation, please pay attention to all safety relevant and legal directions.

The device has only to be installed by trained personnel or similarly qualified people.

2

Safety instructionsThe installation can be executed only by trained qualified personnel. Before the installation disconnectthe power supply. Therefore cut off the battery from the vehicle electric system, follow the manufacturer’sspecification.

• Never use bolts, screws and other fastening elements from car’s safety devices or steeringwheel, brakes because it may influence your driving safety and cause accidents.

• Connect the device only to a 12V vehicle voltage with chassis ground to the car body. This unitcannot be used in large trucks or other vehicles which use a DC 24 V battery wiring systemvoltage.

• Avoid to install the device in places where it could hinder the safe driving or functional efficiencyof the other units installed in the vehicle.

• This unit is only for the use with the following vehicles and model line; Only connectionsdescribed within this instruction manual are allowed or required to use for installation.

• For damage impact caused by faulty installation, unsuitable connections or assembling ininappropriate vehicle types or models Kufatec GmbH &Co.KG assumes no liability.

• We advise you that these units process data out of the MOST protocol from the vehicle. Duringthe assembly of this unit we as supplier have access to a specific model and we as producer don’tknow the overall system you work with.

• Especially in case of changes within the same model line and the same model year we don’tguarantee the usability of our products. In case of the usability of our products with themanufacturer’s changes Kufatec GmbH assumes no liability.

• Kufatec GmbH assumes no liability that the assembly of the unit described in this manual isapproved according the warranty regulations of the single car manufacturers. Please check yourmanufacturer’s conditions and warranty before you begin the installation.

• Kufatec GmbH reserves the right to change the device specification without further notice.

• Errors and changes excepted.

References of legal regulations for operationUse this unit in the intended domain only.

If you use the unit in a foreign domain, if the unit is not installed properly, or if the unit will bereconstructed the operating permit and warranty will expire.

3

Rear view camera• Wide angle presentation of the rear area in MMI via a camera integrated in a handle bar

• Considerably simplified orientation through support lines and fields displayed in the video screen thatchange according to the steering angle

• There are two park modes available – longitudinal and across

• All standard functions remain fully intact

• Simple installation, no wire cutting necessary

Scope of delivery- Cable set- Control device (only for article no. 37169)- Handle bar with integrated camera (only for article no. 37169)

4

Installation instructionsThe following presentation shows the laying of the wires and the position of the single components aswell.

Fig.1

1 – Rear view camera 2 –Rear view camera Control unit

3 – Fuse carrier 4 – CAN-breaking plug 5 - MMI 3G unit

Open the trunk lid. Remove the lining of the trunk lid (fig. 3). This is only inserted.

Fig.2 Fig.3

Loosen the fastening screws (left side, right side) of the side trunk lid lining. Take out the servicecovering plate and unscrew the fastening bolts (fig. 5, 6).

Fig.4 Fig.5 Fig.6

1 5

32

4

5

Take out the trunk illumination and the push button of the trunk lid closing mechanism (in case of elec.trunk lid).

Fig.7 Fig.8

Take out the breakdown triangle and loosen the screws situated beneath (fig. 9).

Fig.9 Fig.10

Remove the necessary bolts of the handle bar. Install the rear view camera (fig. 11). Connect the 2-pinand the FAKRA plug of the camera to the delivered cable set (fig. 12).

Fig.11 Fig.12

Remove the D-column lining. Lay the cable set toward the trunk compartment (fig. 13).

Connect the GRAY video wire coming from the camera with the RVC – control device (GRAY).Connect the GREEN FAKRA plug and the main cable set to the RVC- control unit. Assemble the controlunit.

6

Fig.13 Fig.14 Fig.15

Laying of the wires into the front area of the vehicle (fig. 16). Lever the rear and front kicking plate out ofits frame (fig. 17). Take out the lining of the right A-column.

Fig.16 Fig.17 Fig.18

Loosen the necessary bolts of the glove compartment (fig. 19, 20).

Fig.19 Fig.20

Take the MMI 3G unit out of the centre console (unlocking hook).

Fig.21 Fig.22

7

Video wire connection

MMI 3G unit

Fig.23

The connection of the Quadlock plug takes place via two wires in total.

Transparent – PIN 11Black – PIN 5

Abb. 18

CAN wire connection

CAN breaking plug

Push the pink locking to the right (fig. 25). Press the CAN-breaking plug aback and take out. Actuate thepink locking and remove the cover cap (fig. 26).

Fig.24 Fig.25 Fig.26

Remove the pink safety locking (fig. 27).

Fig.27

8

Actuate the locking and take out the housing of the CAN – breaking plug (fig. 28).

Fig.28

Plug the wires in the following cells:

PIN 14 – Low PIN 14 – High

NOTE: If these PINs are occupied so the wires have to be pinned in the free PINsof the same cable link.

The wire for the permanent positive has to be connected with the respective fuse carrier. Check

before the installation which fuse carrier leads the permanent positive.

Fig.29

After that connect the ground wire with the ground point.

9

Coding

Address 19

Self-diagnostics Address 19 Diagnostics interface for the data bus

Coding Installation list

Set the rear view camera on coded – confirm the coding

10

Address 5F

Byte 07 - Bit 1 set on 1 xxxxxx1x

Address 5F Information electronics Coding Master

Select BIN Enter the coding + confirm

11

Address 6C

Guided error search – carry out the coding

Finally a MMI Reset has to be executed!

Address 17 (if on board)

Coding: 5. Out of right +2 xx?xxxx

Address 10 (if on board)

Coding: Byte 00 – Bit 5