inductors for telecommunications - europower components ltd · inductors for telecommunications. 2...

Data Sheet Collection 2002

Inductors forTelecommunications

Inductors for Telecommunications

The race on the digital information highway is already underway. Growing data traffic volumes aredemanding increasingly higher transmission rates. And multimedia services, such as radio and tele-vision on the Internet, audio and video streaming, videoconferencing, video-on-demand, e-com-merce, etc. require data speeds that far outstrip the rates used by analog technology. Only digitaltransmission technologies can rise to the occasion. Demands for improved circuit design and soft-ware are being accompanied by calls for advanced components. And as long as transmissionroutes use copper lines, this is particularly relevant for inductive components. Such components areessential if transmission quality levels and existing EMC, personal safety and device protectionguidelines are to be observed.

The first step on the road to digitalization was the introduction of ISDN (Integrated Services DigitalNetwork). The worldwide standardization of ISDN means that interfaces, and thereby interfacetransformers, are clearly defined. Transformers and chokes are used with the interfaces

� ��

Essentially, the transformer is defined by the chip set used. EPCOS provides interface transformersfor the leading semiconductor manufacturers.

The next stage in the digital race brings us to DSL (Digital Subscriber Line). The term xDSL is usedto refer to the various technologies that increase bandwidth levels on existing copper lines.

These technologies also require interface transformers tailored to suit specific semiconductor chips.And EPCOS provides the standard model. Some of the xDSL technologies (e.g. ADSL, SDSL) alsouse a passive splitter to separate telephone and data signals. Since the interfaces for this filter havenot yet been standardized, EPCOS mainly develops the inductive components for this splitter on acustomer-specific basis.

Do not miss to visit us on Internet:

http://www.epcos.com/inductors

1 04/02


Contents

Page

ISDN transformers 8

IC reference list 8Transformers:– S0 interface 11– S2M interface 22– UK0 interface 23– UPN interface 38

Power supply 40

xDSL transformers 42

ADSL interface 42MDSL interface 51S(H)DSL interface 53HDSL interface 55

Data line chokes 56

– S0 interface 56– UK0/UPN interface/ xDSL transformers 64

Symbols and terms 73

Addresses 74

2 04/02


Selector Guide

ISDN transformers

Type Application Version Ordering code Page

ISDN S0 interface

RM 5 S0 interface B78384A1060A002 11

S0 interface PTH B78384P1111A005 12

R 10 S0 interface B78510A1452A003 13

S0 interface B78510A1223A003 14

S0 interface PTH B78510P1365A005 15

Modules S0 interface modules PTH B78475P1560A002 16

S0 interface modules PTH B78475P1561A002 18





ISDN S2M interface

E 6,3 S2M interface B78304B1144A003 22

S2M interface B78304B1145A003 22

ISDN UK0 interface

EP 13 UK0 interface B78421A1720A003 23

UK0 interface B78421A1721A003 24

UK0 interface PTH B78421P1582A005 25


RM 6 UK0 interface PTH B78386P1580A005 27









RM 8 UK0 interface PTH B78388P1254A005 34



UK0 interface PTH B78388Q1333A005 37

3 04/02


Selector Guide

ISDN UPN interface

RM 4 LP UPN interface B78381A1134A003 38

E 13 UPN interface B78308A1123A003 39

ISDN transformers

EF 16 AC/DC converter PTH B78310P1583A005 40

EF 16 DC/DC converter PTH B78310P1623A005 41

xDSL transformers

ADSL transformers

EP 7 ADSL interface B78417A1698A003 42

ADSL interface B78417A1671A003 43

ADSL low pass filter B78417A1706A003 44

ADSL low pass filter B78417A1701A003 45

EP 13 ADSL filter chokes B78421A1639A003 46

ADSL interface B78421A1704A003 47

ADSL interface PTH B78421P1482A005 48



MDSL transformers

EP 13 MDSL interface PTH B78421P1544A005 51

S(H)DSL transformers

EP 13 S(H)DSL interface B78421A1709A003 52

S(H)DSL interface PTH B78421P1624A005 53

S(H)DSL interface PTH B78421P1705A005 54

HDSL transformers

EP 13 HDSL interface PTH B78421P1457A005 55


4 04/02


Selector Guide

Data line chokes

ISDN applications

Quad chokes

S0 interface B82793C2... 56

S0 interface B82792C2... 58

S0 interface PTH B82796C2... 60

S0 interface PTH B82719C2... 62

ISDN/xDSL applications

Double chokes

UK0/UPN interface; xDSL transformers B82793C0...B82793S0...

64

UK0/UPN interface; xDSL transformers B82792C0... 67

UK0/UPN interface; xDSL transformers PTH B82796C0...B82796S0...

69

UK0/UPN interface; xDSL transformers PTH B82719C0... 71


5 04/02


Index of Ordering Codes

Ordering code Page Ordering code Page

B78304B1144A003 22

B78304B1145A003 22

B78308A1123A003 39

B78310P1583A005 40

B78310P1623A005 41

B78381A1134A003 38

B78384A1060A002 11

B78384P1111A005 12

B78386P1114A005 32

B78386P1115A005 32

B78386P1116A005 33

B78386P1127A005 33

B78386P1556A005 31

B78386P1580A005 27

B78386P1648A005 28

B78386P1662A005 29

B78386P1703A005 30

B78388P1254A005 34

B78388P1334A005 36

B78388P1347A005 35

B78388Q1333A005 37

B78417A1671A003 43

B78417A1698A003 42

B78417A1701A003 45

B78417A1706A003 44

B78421A1639A003 46

B78421A1704A003 47

B78421A1709A003 52

B78421A1720A003 23

B78421A1721A003 24

B78421P1457A005 55

B78421P1482A005 48

B78421P1486A005 49

B78421P1544A005 51

B78421P1579A005 50

B78421P1582A005 25

B78421P1624A005 53

B78421P1649A005 26

B78421P1705A005 54

B78475P1560A002 16

B78475P1561A002 18

B78475P1562A002 18

B78475P1563A002 18

B78475P1564A002 21

B78475P1565A002 21

B78510A1223A003 14

B78510A1452A003 13

B78510P1365A005 15

B82719C0106N365 71

B82719C0226N365 71

B82719C0336N365 71

B82719C0475N365 71

B82719C0476N365 71

B82719C0685N365 71

B82719C2105N365 62

B82719C2474N315 62

B82719C2475N365 62

B82792C0106N365 67

B82792C0226N365 67

B82792C0336N365 67

B82792C0475N365 67

B82792C0506N365 67

B82792C0685N365 67

B82792C2105N365 58

B82792C2474N315 58

B82792C2475N365 58

B82793C0105N265 64

B82793C0113N201 64

6 04/02


Index of Ordering Codes

Ordering code Page Ordering code Page

B82793C0225N265 64

B82793C0474N215 64

B82793C0475N265 64

B82793C0502N201 64

B82793C2113N201 56

B82793C2225N265 56

B82793C2473N201 56

B82793C2474N215 56

B82793S0253N201 64

B82793S0513N201 64

B82796C0105N265 69

B82796C0113N201 69

B82796C0225N265 69

B82796C0474N215 69

B82796C0475N265 69

B82796C0502N201 69

B82796C2113N201 60

B82796C2225N265 60

B82796C2473N201 60

B82796C2474N215 60

B82796S0253N201 69

B82796S0513N201 69

7 04/02

ISDN Transformers

IC Reference List

IC reference list

The ISDN interface transformers from EPCOS are matched to semiconductors from various produ-cers. Different versions � electrically and mechanically � are available.

S0 interface modules

IC manufacturer IC part number(ordering code)

EPCOS ordering code Page

Alcatel Microelectronics MTC 2072, 20276MTC 20279, 20172, 20277, 20278

B78475P1560A002B78475P1562A002

1618

AMD AM 79C30A AM 79C32A

B78475P1560A002B78475P1562A002B78475P1565A002

161820

Cologne Chip Des. HFC-S2BDS0 B78475P1560A002B78475P1562A002

1618

Infineon PEB/PSB 21150, 21381/2,21383/4, 2154, 3081, 3086, 3186

B78475P1563A002 18

PEB/PSB 2080, 2081, 2084, 2085, 2086, 2115, 2186, 8090, 8091, 8191

B78475P1560A002B78475P1562A002B78475P1565A002

161820

Intel 29C53AA B78475P1561A002B78475P1564A002

1820

Lucent T 7234, 7250, 7252, 7256, 7259, 9000 B78475P1561A002B78475P1564A002

1820

Mietec MTC-2072 B78475P1560A002B78475P1562A002B78475P1565A002

161820

Mitel MT 8930, MT 8931

B78475P1560A002B78475P1562A002B78475P1565A002

161820

Motorola MC 145574, 145576 B78475P1561A002B78475P1564A002

1820

National Semiconductor TP 3420, 3421 B78475P1560A002B78475P1562A002B78475P1565A002

161820

STM ST 5420, 5421 B78475P1560A002B78475P1562A002B78475P1565A002

161820

VLSI VN S8000 B78475P1560A002B78475P1562A002

1618

8 04/02

ISDN Transformers

IC Reference List

S0 interface transformers

UK0 interface transformers

Transmission code 2B1Q

IC manufacturer IC part number (ordering code) EPCOS transformer Page

Infineon PEB/PSB2080, 2081, 2084, 2085, 2086,2115, 2186,8090, 8091, 8191

B78384A1060A002B78510A1223A003B78384P1111A005B78510P1365A005

11141215

PEB/PSB21381, 21382, 21383, 21384 B78510A1452A003 13

AMD AM 79C30A,AM 79C32A

B78384A1060A002B78510A1223A003B78384P1111A005B78510P1365A005

11141215

Mietec MTC 2072, 20276, 20277, 20278, 20279

B78384A1060A002B78510A1223A003B78384P1111A005B78510P1365A005

11141215


Infineon PEB/PSB2091,24902, 24911,8091, 8191

B78386P1114A005B78386P1116A005B78388P1254A005B78388P1347A005B78388P1334A005

3233343536

PEF Q-Smint®

80912, 80913,81912, 81913,82912, 82913

B78386P1580A005B78421P1582A005B78386P1662A005B78421A1720A003

27252923

AMD AM 2091 B78386P1114A005B78386P1116A005B78388P1254A005B78388P1347A005B78388P1334A005

3233343536

9 04/02

ISDN Transformers

IC Reference List

UK0 interface transformers

Transmission code 4B3T

DSL interface transformers


Infineon PEB/PSB2090, 20901, 20902, 24901, 24902,8090

B78386P1115A005B78386P1127A005B78388Q1333A005

323337

PEF T-Smint®

80902, 80903,81902, 81903,82902, 82903

B78386P1648A005B78421P1649A005B78386P1703A005B78421A1721A003

28263024

AMD AM 20902 B78386P1115A005B78386P1127A005B78388Q1333A005

323337

Mietec MTC 2071 B78386P1115A005B78386P1127A005B78388Q1333A005

323337

MTC 20279 B78386P1556A005 31

IC manufacturer IC part number (ordering code) EPCOS ordering code Page

ADSL

Analog Device AD 20 MSP 910 B78421P1482A005 48

Alcatel MKT-20140 B78421P1486A005 49

Infineon PEB 22715 B78421P1579A005 50

GEMINAXPEB 4565, 3558, 22716, 22720

B78417A1698A003B78417A1671A003B78417A1706A003B78417A1701A003B78421A1639A003

4243444546

Texas Instruments TNETD 3000/4000 B78421A1704A003 47

S(H)DSL

Infineon SOCRATESPEB 22622, 22623, 24622

B78421P1624A005B78421A1709A003

5352

Metalink MtS 141AFE B78421P1705A005 53

HDSL

Booktree BT 8960 B78421P1457A005 55

MDSL

Infineon MUBIC PEB 22522 B78421P1544A005 51

10 04/02

RM 5

B78384A1060A002S0 Interface

ISDN Transformers

Application

� Use in TE and NT/PBX� Matched to the ICs, e.g.

Infineon PEB/PSB 8091, 8191 and 8090;AMD AM 79C30A and 79C32A;MIETEC MTC 2072, 20276...20279

Features

� Complies with CCITT 1.430� Remote power feeding to TE

Marking

� Manufacturer, middle block of ordering code, date code

Packing

� 520-mm stick magazine� Packing unit: 300 pcs.

Pinning

Technical data (electrical specifications at 25 °C)

Ordering code B78384A1060A002

Type/Core RM 5

N1 : N2 : N3 : N4 1 : 1 : 2 : 2

LH mH � 30

LS (typ.) �H 6

CK (typ.) pF 120

CW (typ.) pF 80

RDC (Line) (typ.) � 1,6

RDC (IC) (typ.) � 3,3

VT kVAC 1,5

�IDC (typ.) mA 12

Operating temperature range °C –25/+85

FIN0168-C

8

7

6

54

3

2

1

19,5 max.

3,81 14

,5 m

ax.

0,8

max

.

16,5

max

.

11 m

ax.

3x3,

81=1

1,43

0,5

0,5

_

Layout recommendation

FIN0169-K20,5

2,5

3,81

1,5 12

,93

FIN0217-R-E

1

4

3

2IC *

3N

N4

*

N1

N2

8

5

6

7Line

* = external connection

11 04/02

RM 5

B78384P1111A005S0 Interface

ISDN Transformers

Application



Features


Marking


Packing

� Polyfoam tray� Packing unit: 500 pcs.

Pinning


Ordering code B78384P1111A005

Type/Core RM 5

N1 : N2 : N3 : N4 1 : 1 : 2 : 2

LH mH � 30

LS (typ.) �H 6

CK (typ.) pF 120

CW (typ.) pF 80


RDC (IC) (typ.) � 3,3

VT kVAC 0,5

�IDC (typ.) mA 12


FIN0170-X

13,2

max.

17,5 max.

12

8

7

3

6

4,05

max

.

4

5

10,5

max

.FIN0171-F-E

ø1+0,1

Ground ø1,3+0,1

2,54

Recommended holearrangement(view in mounting direction)

FIN0218-Z-E

6

5

3

4IC * *

2

8

7

1Line

2N

1N

4N

N3


12 04/02

R 10


ISDN Transformers

Application

� Use in TE and NT/PBX� Matched to Infineon ICs

PEB/PSB 21381...21384

Features


Marking


Packing

� 24-mm blister tape� Packing unit: 500 pcs.

Pinning



Type/Core R 10

N1 : N2 : N3 : N4 1 : 1 : 1 : 1

LH mH > 22

LS (typ.) �H 3,6

CK (typ.) pF 65


RDC (IC) (typ.) � 2,2

VT kVAC 2,0

�IDC (typ.) mA 3,3


FIN0172-N

2

5

4

1

17,2 max.

2,54

97

6

5,08

10

2,54

13,5

max

.

10,7

6

10,3

max

.


FIN0173-V

3,5 11 2,543,5

1,5

5,08

2,54


FIN0100-A

1

5

2

4*

1N

N2

N3

10

6

7

N4

IC Line

13 04/02

R 10


ISDN Transformers

Application


Infineon PEB/PSB 8090, 8091, 8191;AMD AM 79C30A and 79C32;MIETEC MTC 2072, 20276...20279

Features


Marking


Packing


Pinning



Type/Core R 10

N1 : N2 : N3 : N4 1 : 1 : 2 : 2

LH mH � 22

LS (typ.) �H 6

CK (typ.) pF 52

CW (typ.) pF 116


RDC (IC) (typ.) � 4,2

VT kVAC > 2,0



FIN0172-N

2

5

4

1

17,2 max.

2,54

97

6

5,08

10

2,54

13,5

max

.

10,7

6

10,3

max

.


FIN0173-V

3,5 11 2,543,5

1,5

5,08

2,54

FIN0098-R

1

5

2

4*

1N

N2

N3

N4

10

6

7IC Line


14 04/02

R 10

B78510P1365A005S0 Interface

ISDN Transformers

Application



Features


Marking


Packing


Pinning



Type/Core R 10

N1 : N2 : N3 : N4 1 : 1 : 2 : 2

LH mH � 22

LS (typ.) �H 6,0

CK (typ.) pF 52

CW (typ.) pF 116


RDC (IC) (typ.) � 4,2

VT kVAC 2,0



FIN0174-D

14,2 max.

43

21

12,7

max

.

56

78

8,3

max

.

9,8

max

.

FIN0175-L

56

78

ø1,2+0,1

43

12,7

21

10,1

6

2,54

2,54

Recommended hole arrangement(view in mounting direction)


FIN0098-R

1

5

2

4*

1N

N2

N3

N4

10

6

7IC Line

15 04/02

ISDN Transformers

S0 Interface Modules

B78475P1560A002

Construction

� Two S0 interface transformers (transmitter/receiver) in one case

� Additional quad chokes

Application

� NT, peripheral devices (telephone, fax, modems)� For all leading semiconductor manufacturers

(refer to reference list)

Features

� Low space due to compact construction� Low logistic effort� Simple and fast assembly

Marking


Packing

� Stick magazine� Packing unit: 2006 pcs.

Pinning

FIN0131-D

Marking

ø0,6

30 max.

15,1

max

.

3,5

11 m

ax.

8,89

20,32

2,54

1

18 10

9

FIN0134-B

29

10

3NN 1

17 N 4

N9

N10

1

18

PRI SEC

14

5

N12

15

N4

47N

8N11

N 5

8

3

16

16 04/02


ISDN Transformers B78475P1560A002


(electrical specifications at 25 °C)


Turn ratio (�� 1 %) N3 : N4 : N1N7 : N8 : N5N9 : N10 : N11 : N12

1 : 1 : 4 1 : 1 : 4 1 : 1 : 1 : 1

LH (min) mH 30

Choke L (min.) mH 5,0

LS (max.) �H 4,0

Choke LS (max.) �H 0,6

CK (max.) pF 120


RDC (IC) (typ.) � 5,0

RDC (max.) � 1,3


HIPOT Vrms 1500

Operating temperature range °C 0 to 70

17 04/02

ISDN Transformers


B78475P1561A002

... B78475P1563A002

Construction

� Two S0 interface transformers (transmitter/receiver) in one case

� Additional quad chokes

Application


(refer to reference liste)

Features


Marking


Packing


Pinning

FIN0132-L

Marking

ø0,6

30 max.

15,1

max

.

3,5

11 m

ax.

8,89

20,32

2,54

1

18 10

9

FIN0135-J

29

7

3N N 1

17 N 4

N9

N10

1

18

PRI SEC

14

5

N12

15

N4

47N

8N12

N 5

10

3

16

2N8

N 6

11

18 04/02


ISDN Transformers B78475P1561A002

... B78475P1563A002



Ordering code B78475P1561A002 B78475P1562A002 B78475P1563A002

Turn ratio (�� 1 %)

N3:N4:N1:N2N7:N8:N5:N6N9:N10:N11:N12

1 : 1 : 2,5 : 2,51 : 1 : 2,5 : 2,51 : 1 : 1 : 1

1 : 1 : 2 : 2 1 : 1 : 2 : 2 1 : 1 : 1 : 1

1 : 1 : 1 : 11 : 1 : 1 : 11 : 1 : 1 : 1

LH (min.) mH 30 30 30

Choke L (min.) mH 5,0 5,0 5,0

LS (max.) �H 5,0 5,0 5,0

Choke LS (max.) �H 0,5 0,6 0,6

CK (max.) pF 150 150 150

RDC (Line) (typ.) � 1,6 1,4 1,6

RDC (IC) (typ.) � 6,0 4,6 1,6

RDC (max.) � 1,1 1,1 1,1

�IDC (typ.) mA 5,0 5,0 5,0

HIPOT Vrms 1500 2000 1500

Operating temperature range

°C 0 to 70

19 04/02

ISDN Transformers


B78475P1564A002

B78475P1565A002

Construction

� Two S0 interface transformers (transmitter/receiver) in 1 case

Application


(refer to reference list)

Features


Marking


Packing


Pinning FIN0133-T

Marking

ø0,6

30 max.

15,1

max

.

3,5

11 m

ax.

8,89

20,32

2,54

1

18 10

9

FIN0136-R

1

2

3N N 1

17

18

15

16

N 4

4

2N

3

NN

11

8 6

8

12

13

14

N 7

7

6

5N

5

20 04/02


ISDN Transformers

Technical data


Ordering code B78475P1564A002 B78475P1565A002

Turn ratio (�� 1 %) N1 : N 2 : N3 : N4N5 : N 6 : N7 : N8

1 : 1 : 2,5 : 2,51 : 1 : 2,5 : 2,5

1 : 1 : 2 : 2 1 : 1 : 2 : 2

LH (min.) mH 30 30

LS (max.) �H 3,0 5,0

CK (max.) pF 150 150

RDC (Line) (typ.) � 1,6 1,6

RDC (IC) (typ.) � 6,0 5,0

�IDC (typ.) mA 5,0 5,0

HIPOT Vrms 1500 1500

Operating temperature range °C 0 to 70

21 04/02

22 04/02

Application

� Use in PBX and NT� Matched to coaxial 75 � lines

Feature

� Complies with CCITT G.703

Marking


Packing


Pinning


Ordering code B78304B1144A003 B78304B1145A003

Type/Core E6,3 Transmitter E6,3 Receiver

N1 : N2 : N3 0,55 : 1 : 1 1 : 1 : 1

LH mH 0,38 +55/–45 % 1,43 +55/–45 %

LS (typ.) �H 0,2 0,8

RDC (Line) (typ.) � 0,5 1,0

RDC (IC) (typ.) � 1,5 2,0

VT kVAC 0,3 0,3

Operating temperature range °C –25/+85 –25/+85

FIN0178-J

3

1

5

1

9 max.

1 max.

2,54

±0,2

4

2

6

0,8

max

.

5,08

±0,2

7,7

max

.

5,7

max

.

FIN0179-R

1,2

9,5

1,2

2,54

5,08



E 6,3ISDN Transformer

B78304B114*A003S2M Interface

UK0 Interface

ISDN Transformers EP 13

B78421A1720A003

Application

� Matching to Infineon ICsQ-Smint®o PEF 80912, 80913Q-Smint®ix PEF 81912, 81913Q-Smint®i PEF 82912, 82913

Features

� PTH version upon request

Marking

� Manufacturer, middle block of ordering code,date code

Packing

� 32-mm blister tape� Packing unit upon request

Pinning



Type/Core EP 13

N1 : N2 : N3 1 : 1 : 1

LH mH 14,47�� 8 %

LS (typ.) �H 160

CK (typ.) pF 29


RDC (IC) (typ.) � 3,8

VT kVAC 2,0

IDC (typ.) mA 60



FIN0146-Y

17,2 max.

12,4

max

.

13,5 max.

Pin 1 marking

FIN0147-G

10 9 78 6

1 2 3 4 5

202,

7

1,2

2,5

4 x 2,5 = 10


FIN0155-X-E

6

10

5

1

1N

N2

N379 LineIC

23 04/02

ISDN Transformers

UK0 Interface

EP 13

B78421A1721A003

Application

� Matching to Infineon ICsT-Smint®o PEF 80902, 80903T-Smint®ix PEF 81902, 81903T-Smint®i PEF 82902, 82903

Features


Marking


Packing


Pinning



Type/Core EP 13

N1 : N2 : N3 0,8 : 0,8 : 1

LH mH 7,57�� 10 %

LS (typ.) �H 60

CK (typ.) pF 27


RDC (IC) (typ.) � 1,9

VT kVAC 2,0

IDC (typ.) mA 60



FIN0146-Y

17,2 max.

12,4

max

.

13,5 max.

Pin 1 marking

FIN0147-G

10 9 78 6

1 2 3 4 5

202,

7

1,2

2,5

4 x 2,5 = 10


FIN0155-X-E

6

10

5

1

1N

N2

N379 LineIC

24 04/02

UK0 Interface

ISDN Transformers EP 13

B78421P1582A005

Application


Marking


Packing

� Polyfoam tray� Packaging unit: 500 pcs.

Pinning



Type/Core EP 13

N1 : N2 : N3 1 : 1 : 1

LH mH 14,47�� 8 %

LS (typ.) �H 160

CK (typ.) pF 29


RDC (IC) (typ.) � 3,8

VT kVAC 2,0

IDC (typ.) mA 80



FIN0128-A

2,54

13,3

max

.

3,5±

0,5

15,9

max

.

12345

109876

ø1,2+0,1

345

21

678910

14,8 max.

10,16

10,1

6

Marking of pin row including pin 1


FIN0139-P

1

5Line3N

10

6

IC

N2

N1

79

25 04/02

ISDN Transformers

UK0 Interface

EP 13

B78421P1649A005

Application


Features

� SMD version upon request

Marking


Packing

� Polyfoam tray � Packing unit: 500 pcs.

Pinning



Type/Core EP 13

N1 : N2 : N3 0,8 : 0,8 : 1

LH mH 7,57�� 10 %

LS (typ.) �H 60

CK (typ.) pF 27


RDC (IC) (typ.) � 1,9

VT kVAC 2,0

IDC (typ.) mA 60



FIN0128-A

2,54

13,3

max

.

3,5±

0,5

15,9

max

.

12345

109876

ø1,2+0,1

345

21

678910

14,8 max.

10,16

10,1

6



FIN0155-X-E

6

10

5

1

1N

N2

N379 LineIC

26 04/02

UK0 Interface

ISDN Transformers RM 6

B78386P1580A005

Application


Marking


Packing


Pinning



Type/Core RM 6

N1 : N2 : N3 1 : 1 : 1

LH mH 14,44�� 10 %

LS (typ.) �H 40

CK (typ.) pF 65


RDC (IC) (typ.) � 2,4

VT kVAC 2,0

IDC (typ.) mA 80



FIN0142-S

+ ++ +

+ + + +

17,9 max.

15,1

max

.

3,4

max

.

0,45

18,5

max

.

21 max.

Pin 1

1)

with clamp1)

marking

FIN0143-A

3,81

3,8115

,24

5,08

17,78

ø1,3+0,2

1 2 3 4

5678

ø1+0,15

Recommended holearrangement(view in mounting direction)FIN0230-B-E

1

4Line3N

8

5

IC

N2

N1

67

27 04/02

ISDN Transformers

UK0 Interface

RM 6

B78386P1648A005

Application


Features


Marking


Packing


Pinning



Type/Core RM 6

N1 : N2 : N3 0,8 : 0,8 : 1

LH mH 7,61�� 10 %

LS (typ.) �H 25

CK (typ.) pF 65


RDC (IC) (typ.) � 1,4

VT kVAC 2,0

IDC (typ.) mA 80



FIN0143-A

3,81

3,81

15,2

4

5,08

17,78

ø1,3+0,2

1 2 3 4

5678

ø1+0,15

Hole arrangement (view in mounting direction)

FIN0142-S

+ ++ +

+ + + +

17,9 max.

15,1

max

.

3,4

max

.

0,45

18,5

max

.

21 max.

Pin 1

1)

with clamp1)

marking

FIN0154-P

8

5

1

4

1N

N2

N376Line IC

28 04/02

UK0 Interface


B78386P1662A005

Application


Features

� Potted acc. to EN 60950, reinforced insulation

Marking


Packing

� Polyfoam tray � Packing unit upon request

Pinning



Type/Core RM 6

N1 : N2 : N3 1 : 1 : 1

LH mH 14,44�� 10 %

LS (typ.) �H 190

CK (typ.) pF 10


RDC (IC) (typ.) � 1,7

VT kVAC 5,0

IDC (typ.) mA 80



FIN0156-F-E

Pin 1

3,1

max

.

14 max.

20 max.

20 max.

0,45

15,7

max

.

15,24 3,81

3,81

5,08

ø1+0,15

FIN0157-N

1

2

3

4 5

6

7

8Hole arrangement (view in mounting direction)

FIN0158-V

1 8

5

1N4

IC

Line76

N2

N3

29 04/02

ISDN Transformers

UK0 Interface

RM 6

B78386P1703A005

Application


Features

� Potted acc. to EN 60950, reinforced insulation

Marking


Packing

� Polyfoam tray � Packing unit upon request

Pinning



Type/Core RM 6

N1 : N2 : N3 0,8 : 0,8 : 1

LH mH 7,61�� 10 %

LS (typ.) �H 90

CK (typ.) pF 22


RDC (IC) (typ.) � 1,6

VT kVAC 4,0

IDC (typ.) mA 80



FIN0156-F-E

Pin 1

3,1

max

.

14 max.

20 max.

20 max.

0,45

15,7

max

.

15,24 3,81

3,81

5,08

ø1+0,15

FIN0157-N

1

2

3

4 5

6

7

8Hole arrangement (view in mounting direction)

FIN0154-P

8

5

1

4

1N

N2

N376Line IC

30 04/02

UK0 Interface


B78386P1556A005

Application

� Use in NT and local central office� Matched to Mietec IC

MTC 20279 (4B3T)

Features

� Complies with CCITT G.961� Remote power feeding to NT

Marking


Packing


Pinning



Type/Core RM 6

N1 : N2 : N3 0,8 : 0,8 : 1

LH mH 6,08�� 10 %

LS (typ.) �H 50

CK (typ.) pF 125


RDC (IC) (typ.) � 1,9

VT kVAC 0,5

IDC (typ.) mA 80



Ground ø1,3+0,1

ø1,2+0,1

2,54

15,5 max.

4,5

max

.12

,5 m

ax.

FIN0130-V

15,5

max.

5

43

6

12

1,6

max

.

Recommended hole arrangement

Marking of Pin 1 (slot)

FIN0129-I

2

5

1

4

1N

N2

N336Line IC

31 04/02

ISDN Transformers

UK0 Interface

RM 6

B78386P111*A005

Application

� Use in NT and local central office� Matched to the ICs, e.g.

...P1114: Infineon PEB/PSB 8091, 8191;B78386P AMDAM 2091...P1115: Infineon PEB/PSB 8090; B78385: AMDAM20902; MIETEC MTC2071

Features


Marking


Packing


Pinning



Type/Core RM 6 RM 6

N1 : N2 : N3 0,8 : 0,8 : 1 0,66 : 0,66 : 1

LH mH 14,5 � 10 % 5,5 � 10 %

LS (typ.) �H 87 22

CK (typ.) pF 130 130

RDC (Line) (typ.) � 5,8 3,6

RDC (IC) (typ.) � 4,2 3,0

VT kVAC 0,5 0,5

IDC (typ.) mA 50 80

Transmission code 2B1Q 4B3T


FIN0182-U

15,5

max.

6

15,5 max.

12

4,5

max

.

43

5

12,5

max

.FIN0183-C-E

ø1,3+0,1

Ground ø1,3+0,1

2,54

ø1+0,1


FIN0219-H-E

1

4IC

2

5

36 Line

3N N1

N2

32 04/02

UK0 Interface


B78386P11**A005

Application


...P1116: Infineon PEB/PSB 8091, 8191;B78386P1AMD AM 2091...P1127: Infineon PEB/PSB 8090; B78386PAMD AM 20902; MIETEC 2071

Features


Marking


Packing


Pinning



Type/Core RM 6 RM 6

N1 : N2 : N3 : N4 1,6 : 1,6 : 1 : 1 1,32 : 1,32 : 1 : 1

LH mH 13,3 � 10 % 7,7 � 10 %

LS (typ.) �H 45 40

CK (typ.) pF 70 45

RDC (Line) (typ.) � 5,0 3,8

RDC (IC) (typ.) � 5,0 3,8

VT kVAC 2,5 2,5

IDC (typ.) mA 60 60

Transmission code 2B1Q 4B3T


FIN0184-K

4

1

3

2

18,4 max.25 max.

5

16 m

ax.

4±0,

3

8

7

6

20 m

ax.

13,5

max

.

FIN0185-S-E

ø1+0,1

Ground ø1,3+0,15

15,242,54

17,7

8

12,7

5,08


FIN0220-U-E

5

8

6

7IC *

1

4

32 Line

3N

N4

N1

N2


33 04/02

ISDN Transformers

UK0 Interface

RM 8

B78388P1254A005

Application


Infineon PEB/PSB 8091, 8191;AMD AM 2091

Features


Marking


Packing


Pinning



Type/Core RM 8

N1 : N2 : N3 0,8 : 0,8 : 1

LH mH 14,5 � 10 %

LS (typ.) �H 63

CK (typ.) pF 90


RDC (IC) (typ.) � 2,7

VT kVAC 2,0

IDC (typ.) mA 60



FIN0186-A

16,5

max

.4,

5 m

ax.

21 max. 21 m

ax.

1112

12

87

65

FIN0187-I-E

2,54

Ground ø1,3+0,1

ø1,2+0,1Recommended holearrangement(view in mounting direction)


34 04/02

UK0 Interface


B78388P1347A005

Application

� Use in NT and local central office� Matched to the ICs, e.g. AMD AM 2091;

Infineon PEB/PSB 8091 and 8191

Features

� Complies with CCITT G.961� Remote power feeding to NT� According to EN 60950: reinforced insulation,

operating voltage 120 V

Marking


Packing


Pinning



Type/Core RM 8

N1 : N2 : N3 0,8 : 0,8 : 1

LH mH 14,5 � 10 %

LS (typ.) �H 140

CK (typ.) pF 45


RDC (IC) (typ.) � 6,5

VT kVAC 3,0

IDC (typ.) mA 100



FIN0188-Q

21 max.

1

2

1211

3

10

21 m

ax.

4

5

9

8

6

7

4,5

max

.16

,5 m

ax.

FIN0189-Y-E

2,54

Ground ø1,3+0,1

ø1,2+0,1



FIN0085-M

12

2

1

11IC*

1N

N2

N3

6

7

Line

35 04/02

ISDN Transformers

UK0 Interface

RM 8

B78388P1334A005

Application

� Use in NT and local central office� Matched to the ICs, e.g. AMD AM2091;

Infineon PEB/PSB 8091 and 8191

Features



Marking


Packing


Pinning



Type/Core RM 8

N1 : N2 : N3 0,8 : 0,8 : 1

LH mH 14,5 � 10 %

LS (typ.) �H 70

CK (typ.) pF 22


RDC (IC) (typ.) � 3,0

VT kVAC 4,0

IDC (typ.) mA 50



FIN0192-B

33,5 max.

29 m

ax.

20,5

max

.3,

3±0,

3

7 6

49

310

112

FIN0193-J

7,62

5,08

7,62

20,32

8 x 1,6+0,1



FIN0087-C

1

4

3

2IC*

1N

N2

N3

6

7

Line

36 04/02

UK0 Interface


B78388Q1333A005

Application

� Use in NT and local control office� Matched to the ICs, e.g. AMD AM 20902;

Infineon PEB/PSB 8090; MIETEC MTC 2071

Features



Marking


Packing


Pinning


Ordering code B78388Q1333A005

Type/Core RM 8

N1 : N2 : N3 0,66 : 0,66 : 1

LH mH 5,5 � 10 %

LS (typ.) �H 110

CK (typ.) pF 30


RDC (IC) (typ.) � 2,7

VT kVAC 2,0

IDC (typ.) mA 100



FIN0194-R

16,5

max

.4,

5 m

ax.

1

2

3

12 1011

4

5

6

9 78

21 m

ax.21 max.

FIN0195-Z

ø1,2+0,1

2,54



FIN0091-N

11

1

2

12IC*

1N

N2

N3

6

7

Line

37 04/02

ISDN Transformers

UPN Interface

RM 4 LP

B78381A1134A003

Application

� Use in TE and PBX� Matched to Infineon ICs, e.g.

PEB/PSB 2095 and 20950

Feature

� Remote power feeding to TE

Marking


Packing


Pinning



Type/Core RM 4 LP

N1 : N2 : N3 1 : 1 : 4

LH mH 2,2 � 10 %

LS (typ.) �H 30

CK (typ.) pF 70


RDC (IC) (typ.) � 22

VT kVAC 0,5

IDC (typ.) mA 140


FIN0198-X

1

8,1

max

.

13,8 max.

3

26

4

5

12,4

max

.

0,8 max.

FIN0199-F

30˚

1,630˚

3,4

14,6


FIN0231-J-E

6

1IC

2

5

43 Line

3N N1

N2

38 04/02

UPN Interface

ISDN Transformers E 13

B78308A1123A003

Application

� Use in TE and PBX� Matched to Infineon ICs, e.g.

PEB/PSB 2095 and 20950

Feature

� Remote power feeding to TE

Marking


Packing


Pinning



Type/Core E 13

N1 : N2 : N3 1 : 1 : 4

LH mH 2,2 � 15 %

LS (typ.) �H 20

CK (typ.) pF 140


RDC (IC) (typ.) � 21

VT kVAC 0,5

IDC (typ.) mA 90


FIN0200-C

10

9

8

7

65

4

3

2

1

14 m

ax.

0,8

max

.9,

6 m

ax.

20 max.

13,3 max.

FIN0201-O21

2,54

2,54

10,1

6

1,3


FIN0216-J-E

4

2IC

6

10

79 Line

3N N1

N2

39 04/02

40 04/02

ISDN Transformers

AC/DC Converter

Application

� Matched to InfineonSIPB 20233

Features

� According to EN 60950:Reinforced insulationCreepage path = 8 mmClearance path = 4 mm

Marking


Packing


Pinning



Type/Core EF 16

N1 : N2 : N3 1 : 0,125 : 0,417

L1 �H 323 � 20 %

Pmax W 12

f kHz 240

Vin kVDC 0,11 ... 0,35

VT kVAC 3,0


FIN0144-I

24 m

ax.

0,64

16,4 max.

4,4

max

.

20 max.

FIN0145-Q

1 2 4 5

678915

3,75 3,757,5

ø1,6+0,2


FIN0151-R

1

5

24

1N

N2

N3

7

6

Primary

Sense

Output

11,2 V

40 V

EF 16

B78310P1583A005

41 04/02

DC/DC Converter

ISDN Transformers

Application

� DC/DC converter (3,3 V) for INCA-S/P telefon board

� Matching to the following Infineon INCA sets:INCA-S (S0) PSB 21483INCA-P (UPN) PSB 21493

Marking


Packing


Pinning



Type/Core EF 16

N1 : N2 : N3 : N4 : N5 1 : 0,28 : 0,49 : 0,28 : 1

LH mH 8,4�� 20 %

Pout W 10

f kHz 240

VT kVAC 0,5


FIN0149-W

18 max.

14 m

ax.

4,5

max

.

20 max.

Pin 1 marking

FIN0150-J

3,81

3,81

15,2

4

3,81

ø1,3+0,2

1 2 3 4

5678


FIN0148-O

4

3

1

1N

N5

N2

8

7

Sense6

5N3

N4

-12 ... -60 V

0 V

+12 ... +60 V

3,3 V

5,9 V

EF 16

B78310P1623A005

EP 7

B78417A1698A003ADSL Interface

xDSL Transformers

Application

� Matched to Infineon ICsGEMINAX PEB 4565, 3558, 22716, 22720

Features


Marking


Packing


Pinning



Type/Core EP 7

N1 : N2 : N3 : N4 1,31 : 1,31 : 1,1

LH mH 1,444�� 10 %

LS (typ.) �H 4,5

CW (typ.) pF 36


RDC (IC) (typ.) � 1,15

VT kVAC 1,5

Insertion loss dB 0,5

THD (at 30 kHz) dB 80


FIN0163-O

5 6 87

4 3 2 19,15 2

1

2,5

8,5


FIN0162-G-E

10 max.

10,9

max

.

2,5

7,5

Pin 1

0,4 x 0,4

7,67 max.

8,55 max.

FIN0164-W

8

5

67

1

4

32

3N

N4

N1

N2

IC Line

42 04/02

EP 7


xDSL Transformers

Application

� Matched to Infineon ICsGEMINAX PEB 4565, 3558, 22716, 22720

Features


Marking


Packing


Pinning



Type/Core EP 7

N1 : N2 : N3 : N4 1,31 : 1,31 : 1,1

LH mH 1,444�� 10 %

LS (typ.) �H 4,5

CW (typ.) pF 36


RDC (IC) (typ.) � 1,15

VT kVAC 1,5

Insertion loss dB 0,5




0,7 x 0,25

10,8 max.

Pin 1 2,5

10 max.

13 max.

FIN0229-U-E

Pin 1

7,5 max.

0,2

9 m

ax.

marking

FIN0224-A

8 7 56

1 2 3 4

14

2

1,3

2,5

3 x 2,5 = 7,5

8,8

FIN0225-I

5

8

4

1

3N

N4

76

N1

2N

32IC Line

43 04/02

EP 7

B78417A1706A003ADSL Low Pass Filter

xDSL Applications

Application

� Matched to Infineon ICs GEMINAX PEB 4565, 3558, 22716, 22720

Features


Marking


Packing


Pinning



Type/Core EP 7

N1 : N2 : N3 : N4 1 : 1

LH mH 6,76�� 10 %

LS (typ.) �H 250

CK (typ.) pF 3,0

RDC (1�4) (typ.) � 4,95

RDC (5�8) (typ.) � 4,95

VT kVAC 1,5


FIN0163-O

5 6 87

4 3 2 19,15 2

1

2,5

8,5


FIN0162-G-E

10 max.

10,9

max

.

2,5

7,5

Pin 1

0,4 x 0,4

7,67 max.

8,55 max.

FIN0215-B

1

41N N2

8

5

44 04/02

EP 7

B78417A1701A003ADSL Low Pass Filter

xDSL Applications

Application

� Matched to Infineon ICs GEMINAX PEB 4565, 3558, 22716, 22720

Features


Marking


Packing


Pinning



Type/Core EP 7

N1 : N2 1 : 1

LH mH 6,76�� 10 %

LS (typ.) �H 250

CK (typ.) pF 3,0

RDC (1�3) (typ.) � 4,95

RDC (4�6) (typ.) � 4,95

VT kVAC 1,5


FIN0226-Q-E

Pin 111 max. 12,9 max.

9,2

max

.

marking

FIN0227-Y

1 2 3

5 46

1,2

2

13,5

2,54

2 x 2,54 = 5,08


FIN0228-G

1

31N N2

4

6

45 04/02

xDSL Transformers

ADSL Filter chokes

EP 13

B78421A1639A003

Application

� Filter choke for Infineon GEMINAX(without teletax function) PEB 4565, 3558, 22716, 22720

Features


Marking


Packing


Pinning



Type/Core EP 13

N1 : N2 1 : 1

LH mH 19,95�� 7 %

LS (typ.) �H 640

RDC (1�5 (typ.) m� 3,15

RDC (6�10) (typ.) m� 3,15

VT kVAC 0,5


FIN0146-Y

17,2 max.

12,4

max

.

13,5 max.

Pin 1 marking

FIN0147-G

10 9 78 6

1 2 3 4 5

202,

7

1,2

2,5

4 x 2,5 = 10


FIN0138-H

1

51N N2

6

10

46 04/02

xDSL Transformers EP 13


Application

� Matched to Texas Instruments ICs TNETD 3000, 4000

Features

� According to EN 60950: supplementary insulation,operating voltage 150 V


Marking


Packing


Pinning



Type/Core EP 13

N1 : N2 1 : 1,44

LH mH 1,5�� 10 %

LS (typ.) �H <15

CK (typ.) pF <35


RDC (IC) (typ.) � 0,81

VT kVAC 1,875

IDC (typ.) mA 80



FIN0165-E-E

17,2 max.

12,4

max

.

13,5 max.

Pin 1

FIN0166-M

6 7 98 10

5 4 3 2 1

202,

7

1,2

2,5

4 x 2,5 = 10

FIN0167-U

10

71N N2

1

4

IC Line

47 04/02


B78421P1482A005ADSL Interface

Application

� Matched to Analog Device ICAD 20 MSP 910

Feature

� Small compact design� SMD version upon request

Marking


Packing


Pinning



Type/Core EP 13

N1 : N2 : N3 : N4 1 : 1 : 1 : 1

LH mH 5,0 � 10 %


RDC (IC) (typ.) � 2,5

VT kVAC 2,0


FIN0212-D

14,3

max

.

3,5±

0,5

16 m

ax.

321

45 6

78910

15 max.

FIN0213-L

2,54

54321 10

9876

1+0,1


FIN0111-P

5

2

34Line

6

9

87 IC

1N

N2

N3

N4

48 04/02


B78421P1486A005ADSL Interface

Application

� Matched to Alcatel ICMKT-20140

Feature


Marking

� Manufacturer, middle block of � ordering code, date code

Packing


Pinning



Type/Core EP 13

N1 : N2 : N3 : N4 2 : 2 : 1 : 1

LH mH 0,402 � 10 %


RDC (IC) (typ.) � 0,4

VT kVAC 1,5


FIN0212-D

14,3

max

.

3,5±

0,5

16 m

ax.

321

45 6

78910

15 max.

FIN0213-L

2,54

54321 10

9876

1+0,1


FIN0122-E

5

2

34Line

10

7

89 IC

1N

N2

N3

N4

49 04/02

xDSL Transformers

ADSL Interface

EP 13

B78421P1579A005

Application

� Matched to Infineon ICPEB 22715

� CPE

Features

� According to EN 60950:basic insulation, operating voltage 250 V


Marking


Packing


Pinning



Type/Core EP 13

N1 : N2 : N3 : N4 1,77 : 1,77 : 1 : 1

LH (line) mH 1,382�� 10 %

LS (typ.) �H 16


RDC (IC) (typ.) � 0,72

VT kVAC 2,0


FIN0128-A

2,54

13,3

max

.

3,5±

0,5

15,9

max

.

12345

109876

ø1,2+0,1

345

21

678910

14,8 max.

10,16

10,1

6



FIN0127-S

1

5

10

6

1N

N2

N3

N4

842Line Circuit

50 04/02


B78421P1544A005MDSL Interface

Application

� Matched to the Infineon ICMUBIC PEB 22522

Features


Marking


Packing


Pinning



Type/Core EP 13

N1 : N2 : N3 : N4 2 : 2 : 1 : 1

LH (line) mH 9,98�� 10 %

LS (typ.) �H 80

RDC (Line) (typ.) � 13

RDC (IC) (typ.) � 5,2

VT kVAC 2,0


(view in mounting direction)Recommended hole arrangement

21

10

345

ø1,2+0,1

Marking of pin 1

13,5 max.

7

FIN0126-K

2,5

6

8910

103,

7 m

ax.

13,2

max

.12

,55

max

.

FIN0125-C

5

1

7

9

1N

N2

N3

N4

824Line Circuit

51 04/02

xDSL Transformers

S(H)DSL Interface

EP 13

B78421A1709A003

Application

� Matched to Infineon ICsSOCRATES PEB 22622, 22623, 24622

Features

� According to EN 60950: supplementary insulation, operating voltage 250 V


Marking


Packing


Pinning



Type/Core EP 13

N1 : N2 : N3 : N4 1,62 : 1,62 : 1 : 1

LH mH 2,96�� 10 %

LS (typ.) �H 22

CK (typ.) pF 40


RDC (IC) (typ.) � 0,68

RDC (Sense) (typ.) � 2,7

VT kVAC 2,0

IDC (typ.) mA 80



FIN0146-Y

17,2 max.

12,4

max

.

13,5 max.

Pin 1 marking

FIN0147-G

10 9 78 6

1 2 3 4 5

202,

7

1,2

2,5

4 x 2,5 = 10


FIN0160-Q-E

1

5

7

9

2N

N1

N342Line IC

N4 Sense10

6

52 04/02

S(H)DSL Interface


B78421P1624A005

Application

� Matched to Infineon ICs SOCRATES PEB 22622, 22623, 24622

Features



Marking


Packing


Pinning



Type/Core EP 13

N1 : N2 : N3 : N4 : N5 1,61 : 1,61 : 0,5 : 0,5 : 1

LH mH 3,02�� 10 %

LS (typ.) �H 18

CK (typ.) pF 60


RDC (IC) (typ.) � 2,3

RDC (Sense) (typ.) � 5,2

VT kVAC 2,0

IDC (typ.) mA 80


FIN0128-A

2,54

13,3

max

.

3,5±

0,5

15,9

max

.

12345

109876

ø1,2+0,1

345

21

678910

14,8 max.

10,16

10,1

6



FIN0159-D

1 7

9

1N4Line IC8

N3

N4

N510

65

2

N2

Sense

53 04/02

xDSL Transformers

S(H)DSL Interface

EP 13

B78421P1705A005

Application

� Matched to Metalink IC MtS 141 AFE

Features



Marking


Packing


Pinning



Type/Core EP 13

N1 + N2 : N3 1,8 : 1

LH mH 2,704�� 9%

LS (typ.) �H 19

CK (typ.) pF 33

RDC(Line) (typ.) � 2,8

RDC (IC) (typ.) � 1,5

VT kVAC 2,0

IDC (typ.) mA 60


Marking of pin 1

13,5 max.

FIN0222-K-E

3,7

max

.

13,2

max

.12

,55

max

.

(view in mounting direction)Recommended hole arrangement

21

10

45

ø1,2+0,1

7

FIN0223-S-E

2,5

9

10

FIN0161-Y

2

4

7

9

1N

N2

N351Line IC

54 04/02

55 04/02

HDSL Interface

xDSL Transformers

Application

� Matched to Booktree ICBT 8960

Feature

� Data transfer rate 288 kB/s� SMD version upon request

Marking


Packing


Pinning



Type/Core EP 13

N1 : N2 : N3 : N4 1 : 1 : 0,5 : 0,5

LH mH 5,11 � 10 %


RDC (IC) (typ.) � 1,32

VT kVAC 1,5


FIN0208-S

14,3

max

.

3,5±

0,5

16 m

ax.

321

45

678910

15 max.

FIN0209-A

2,54

54321

109876

1+0,1


FIN0110-P

1

5

42

1N

N2

N3

9

7

8

N4

Line IC

EP 13

B78421P1457A005

Data Line Chokes for ISDN

S0 Interface

B82793C2...

Construction

� Current-compensated ring core quad choke with ferrite core� Bifilar winding� Tinned terminals

Features

� Case flame-retardant as per UL 94 V-0� Suitable for reflow soldering

Applications

Suppression of asymmetrical interference coupled in on lines,whereas data signals up to some MHz can pass unaffectedly

Marking

Manufacturer, ordering code (short form),date of manufacture, coded (year, calender week, day of week)

Delivery mode

� 16-mm blister tape, reel packing� Packing unit: 1500 pcs.

Dimensional drawing

SSB1492-L

7,1 max.

10 max.

0,25

±0,0

5

4,8

max

.

+0,40,29 _

1,9±0,2

0,6±0,05

3 x 2,5±0,1

3 x 2,5

10,2

2,85

SSB1535-9

1,2

(4,5

)


56 04/02

S0 Interface

Data Line Chokes for ISDN B82793C2...

General technical data

Characteristics and ordering codes

Higher L values upon request.

Rated voltage VR 42 Vac (50/60 Hz)80 Vdc

Rated current IR Referred to 50 Hz and 60 C ambient temperature

Rated inductance LR Measured with HP 4275AatL 1 mH = 100 kHz, 0,1 mAL > 1 mH = 10 kHz, 0,1 mA(specified per winding)

Inductance tolerance –30/+50 %

Inductance decrease �L/L0 < 10 % at dc magnetic bias with IRStray inductance LS Measured with bridge HP 4275

Measured frequency for L 11 �H = 1 MHz, 5 mAL > 11 �H = 100 kHz, 5 mA

DC resistance Rtyp Typical values, measured at 20 C ambient temperature

Solderability (215 ± 3) °C, (3 ± 0,3) swetting of soldering area � 95 %in accordance with IEC 60068-2-58

Climatic category 40/125/56 (–40 C/+125 C/56 days damp heat test)in accordance with IEC 60068-1

Weight Approx. 0,4 g

LRmH

LS, maxnH

IRmA

Rtyp�

VTVdc, 2 s

Ordering code

0,011 50 200 0,12 750 B82793C2113N201

0,047 100 150 0,15 750 B82793C2473N201

0,470 200 100 0,35 750 B82793C2474N215

2,2 250 100 0,40 750 B82793C2225N265

57 04/02


S0 Interface

B82792C2...

Construction

� Current-compensated ring core quad choke with ferrite core� Bifilar winding� Tinned terminals

Features


Applications

� Suppression of asymmetrical interference coupled in on lines,whereas data signals up to some MHz can pass unaffectedly

� Use e.g. in telecom applications and RF equipment

Marking

Manufacturer, ordering code,date of manufacture (month, year)

Delivery mode


Dimensional drawing

SSB1564-M

2,5±0,2

3 x

2,5±

0,1

11,5 max.

7,3

max

.

14±0,4

2˚...

8˚

A

Beschriftung

10,5 max.

max. 0,1 A

+0,1 0,05

0,6

_+0

,1_

0,4

0,05

SSB1462-Z

1,6

3 x

2,5

9

15


Marking

58 04/02

S0 Interface






Rated inductance LR Measured with HP 4275Aat L 1 mH = 100 kHz, 10 mV

L > 1 mH = 10 kHz, 10 mV(specified per winding)


Inductance decrease �L/L0 < 10 % at dc magnetic bias with IRStray inductance LS Measured at L 1 mH = 100 kHz, 10 mV

L > 1 mH = 10 kHz, 10 mV




Weight Approx. 2 g

LRmH

LS, typnH

IRmA

Rtyp�

VTVdc, 2 s

Ordering code

0,47 200 600 0,25 750 B82792C2474N315

1,0 250 500 0,30 750 B82792C2105N365

4,7 450 300 0,80 750 B82792C2475N365

59 04/02


S0 Interface

B82796C2...

Construction

� Current-compensated ring core quad choke with ferrite core� Plastic case

Features

� Case flame-retardant as per UL 94 V-0� Suitable for automatic insertion� Pins fitting standard PCB grid

Applications


Marking

Ordering code, manufacturer, date of manufacture (month, year)

Dimensional drawing

SSB1486-C

5±0,

2

3 x 2,5±0,2

9,2±0,1

4,6

0,1

_3±

0,2 0,5 x 0,5

6,7±0,1

60 04/02

S0 Interface




Higher L values upon request.



Rated inductance LR Measured with HP 4275A;Measured frequency forL 1 mH = 100 kHz, 0,1 mAL > 1 mH = 10 kHz, 0,1 mA(specified per winding)

Inductance tolerance –30 %/+50 %

Inductance decrease �L/L0 < 10 % at dc magnetic bias with IRStray inductance LS Measured at 100 kHz and 5 mA




LRmH

LS, typnH

IRmA

Rtyp�

VTVdc, 2 s

Ordering code

0,011 50 200 0,12 750 B82796C2113N201

0,047 100 150 0,15 750 B82796C2473N201

0,47 200 100 0,35 750 B82796C2474N215

2,2 250 100 0,40 750 B82796C2225N265

61 04/02


S0 Interface

B82719C2...

Construction

� Current-compensated ring core quad choke with ferrite core� Bifilar winding

Features

� Case flame-retardant as per UL 94 V-0� Pins fitting standard PCB grid

Applications


Marking

Manufacturer, ordering code,date of manufacture (coded)

Dimensional drawing

SSB1994-Y

5±0,

2

2,5±0,2

2,8+

0,5

7,5±0,2

9,2 max.

6,8

max

.10

±0,1

5

5±0,1

1,5±

0,1

1 4

58

4,5±0,1

6,2

max

.

7,5±

0,1

0,5

1 4

58 7

2 3

4

62 04/02

S0 Interface






Rated inductance LR Measured with HP 4275A atL 1 mH = 100 kHz, 50 mV

L > 1 mH = 10 kHz, 50 mV

(specified per winding)


Inductance decrease �L/L0 < 10 % at dc magnetic bias with IRStray inductance LS Measured with HP 4275A at 100 kHz and 250 mV


Climatic category 40/125/56 (–40 C/+125 C/56 days damp heat test)acc. to IEC 60068-1


LRmH

LS, typ�H

IRmA

Rtyp�

VTV–, 2 s

Ordering code

0,47 0,2 450 0,25 750 B82719C2474N315

1,0 0,25 400 0,3 750 B82719C2105N365

4,7 0,45 250 0,8 750 B82719C2475N365

63 04/02

Data Line Chokes for Telecommunications

UK0/UPN Interface; xDSL Transformers

B82793C0...

B82793S0...

Construction

� Current-compensated ring core choke with ferrite core� Bifilar winding (B82793C…)� Sector winding (B82793S…)� Tinned terminals

Features

� Reduced component height� Case flame-retardant as per UL 94 V-0� Suitable for reflow soldering

Applications

� B82793C:Suppression of asymmetrical interference coupled in on lines,whereas data signals up to some MHz can pass unaffectedly

� B82793S:Suppression of asymmetrical and symmetrical interferencecoupled in on lines. The high-frequency portions of the symmetricaldata signal are decreased so far that EMC problems can besignificantly reduced

Marking

Manufacturer, ordering code (short form),date of manufacture, coded (year, day of week, calender week)

Delivery mode


64 04/02


Data Line Chokes for Telecommunications B82793C0...

B82793S0...

Dimensional drawing

SSB1350-5

2,5±

0,1

6,0 max.

0,3±

0,05

max. 0,1 A7,1 max.

+0,40,29 _

4,9

max

.

0...6

A

_+0,1

0,6

0,05

Beschriftung


Marking

65 04/02



B82793C0...

B82793S0...





Rated inductance LR Measured with HP 4275AMeasuring frequency at L 1 mH = 100 kHz, 0,1 mA

L > 1 mH = 10 kHz, 0,1 mA(specified per winding)

Inductance tolerance B82793+****N201/N215: �30 %B82793+****N265: –30/+50 %

Inductance decrease �L/L0 < 10 % at dc magnetic bias with IRStray inductance LS Measured with HP 4275A

Measuring frequency at L 11 �H = 1 MHz, 5 mAL > 11 �H = 100 kHz, 5 mA





LRmH

LS, typnH

IR1)

mARtypm�

VTVdc, 2 s

Ordering code

0,005 50 1200 100 250 B82793C0502N201

0,011 50 800 120 250 B82793C0113N201

0,025 1500 800 130 250 B82793S0253N201

0,051 2000 800 160 250 B82793S0513N201

0,470 200 700 200 750 B82793C0474N215

1,0 250 700 200 750 B82793C0105N265

2,2 250 500 400 750 B82793C0225N265

4,7 300 400 550 750 B82793C0475N265

1) Types with higher rated current upon request.

66 04/02



Construction

� Current-compensated ring core choke with ferrite core� Bifilar winding� Tinned terminals

Features


Applications

� Suppression of asymmetrical interference coupled in on lines,whereas data signals up to some MHz can pass unaffectedly

� Telecom interfaces� ISDN systems

Marking

Manufacturer, ordering code,date of manufacture (month, year)

Delivery mode


Dimensional drawing

SSB1453-1

2,5±0,2

3 x

2,5±

0,1

11,5 max.

7,3

max

.

14±0,4

2˚...

8˚

A

Beschriftung

10,5 max.

max. 0,1 A

+0,1 0,05

0,6

_+0

,1_

0,4

0,05


SSB1484-V

15

1,6

9

3 x

2,5

Marking

67 04/02



B82792C0...





Rated inductance LR Measured with HP 4275Aat 10 kHz and10 mV(specified per winding)


Inductance decrease �L/L0 < 10 % at dc magnetic bias with IRStray inductance LS Measured at 10 kHz and 10 mV




Weight Approx. 2 g

LRmH

LS, typnH

IRmA

Rtyp�

VTVdc, 2 s

Ordering code

4,7 500 600 0,4 1000 B82792C0475N365

6,8 500 600 0,5 750 B82792C0685N365

10 600 500 1,1 750 B82792C0106N365

22 800 200 1,6 750 B82792C0226N365

33 1500 100 2,0 750 B82792C0336N365

50 1700 100 2,6 750 B82792C0506N365

68 04/02



B82796S0...

Construction

� Current-compensated ring core double choke with ferrite core� Plastic case

Features

� Case flame-retardant as per UL 94 V-0� Suitable for automatic insertion� Pins fitting standard PCB grid

Applications

� B82796C:Suppression of asymmetrical interference coupled in on lines,whereas data signals up to some MHz can pass unaffectedly

� B82796S:Suppression of asymmetrical and symmetrical interferencecoupled in on lines. The high-frequency portions of the symmetricaldata signal are decreased so far that EMC problems can besignificantly reduced

Marking

Ordering code, manufacturer, date of manufacture (month, year)

Dimensional drawing

SSB1418-D

5,7 max.

0,5 x 0,5

7,5 max.

4,9

max

.3±

0,2

Beschriftung

6±0,2

2,5±

0,2

Marking

69 04/02



B82796C0

B82796S0





Rated inductance LR Measured with HP 4275AatL 1 mH = 100 kHz, 0,1 mAL > 1 mH = 10 kHz, 0,1 mA(specified per winding)

Inductance tolerance B82796+****N201: � 30 %B82796+****N215/N265: –30 %/+50 %

Inductance decrease �L/L0 < 10 % at dc magnetic bias with IRStray inductance LS Measured at 100 kHz and 5 mA




LRmH

LS, typnH

IR1)

mARtyp�

VTVdc, 2 s

Ordering code

0,005 50 1200 0,075 250 B82796C0502N201

0,011 50 800 0,120 250 B82796C0113N201

0,025 1500 800 0,130 250 B82796S0253N201

0,051 2000 800 0,160 250 B82796S0513N201

0,470 200 700 0,200 750 B82796C0474N215

1,0 200 700 0,200 750 B82796C0105N265

2,2 250 500 0,400 750 B82796C0225N265

4,7 300 400 0,550 750 B82796C0475N265

1) Types with higher rated current upon request.

70 04/02



Construction

� Current-compensated ring core double choke with ferrite core� Bifilar winding

Features

� Case flame-retardant as per UL 94 V-0� Pins fitting standard PCB grid

Applications


Marking

Manufacturer, ordering code,date of manufacture (coded)

Dimensional drawing

SSB1993-Q

5±0,

2

2,8+

0,5

7,5±0,2

9,2 max.

6,8

max

.10

±0,1

5

1 2

34

6,2

max

.

4,5±0,1

7,5±

0,1

1 2

4 3

1,5±

0,1

5±0,1

0,5

71 04/02



B82719C0...





Rated inductance LR Measured with HP 4275Aat 10 kHz and 50 mV(specified per winding)


Inductance decrease �L/L0 < 10 % at dc magnetic bias with IRStray inductance LS Measured with HP 4275A at 100 kHz and 250 mV


Climatic category 40/125/56 (–40 C/+125 C/56 days damp heat test)acc. to IEC 60068-1


LRmH

LS, typ�H

IRmA

Rtyp�

VTV–, 2 s

Ordering code

4,7 0,5 500 0,4 750 B82719C0475N365

6,8 0,5 400 0,5 750 B82719C0685N365

10 0,6 300 1,1 750 B82719C0106N365

22 0,8 250 1,7 750 B82719C0226N365

33 1,5 200 2,1 750 B82719C0336N365

47 1,7 150 2,8 750 B82719C0476N365

72 04/02

73 04/02

CK1) Coupling capacitance between windings on IC side and

paralleled windings on line side (f = 10 kHz)

CW1) Winding capacitance of series-connected windings on line side (f = 10 kHz)

f Operating frequency

IDC1) Max. permissible direct current

�IDC1) Max. permissible dc unbalance in the connecting wires

L Inductance

LH Main inductance of series-connected windings on line side(f = 10 kHz, Veff = 100 mV)

Ln Inductance of windings with Nn turns

LS1) Stray inductance (leakage inductance)

N1 : N2 : N3 : N4 Transformation ratio

P Transmittable power

RDC1) DC resistance

RDC (IC)1) DC resistance of series-connected windings on IC side

RDC (Line)1) DC resistance of series-connected windings on line side

Vin Input voltage

VT Test voltage (winding-to-winding f = 50 Hz, t = 1 s)

1) Typical values, if not specified otherwise


Symbols and Terms for Transformers

Herausgegeben von EPCOS AGUnternehmenskommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND� ++49 89 636 09, FAX (0 89) 636-2 26 89

EPCOS AG 2002. Vervielfältigung, Veröffentlichung, Verbreitung und Verwertung dieser Broschüre und ihres Inhalts ohne aus-drückliche Genehmigung der EPCOS AG nicht gestattet.

Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen für Erzeugnisse und Leistungen der Elek-troindustrie, soweit nichts anderes vereinbart wird.

Diese Broschüre ersetzt die vorige Ausgabe.

Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgelegenen Vertrieb der EPCOS AGoder an unsere Vertriebsgesellschaften im Ausland. Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe ent-halten. Auskünfte darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsgesellschaft ein-zuholen.

Published by EPCOS AGCorporate Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY� ++49 89 636 09, FAX (0 89) 636-2 26 89

EPCOS AG 2002. Reproduction, publication and dissemination of this brochure and the information contained therein withoutEPCOS’ prior express consent is prohibited.

Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and ElectronicsIndustry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed.

This brochure replaces the previous edition.

For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representa-tives.

Due to technical requirements components may contain dangerous substances. For information on the type in question pleasealso contact one of our Sales Offices.

inductors for telecommunications - europower components ltd · inductors for telecommunications. 2...

Documents