hanjip restaurant - this area is password protected [401] design alliance, inc. los angeles 2830...
TRANSCRIPT
LIGHTING DESIGN ALLIANCE, INC.
LOS ANGELES2830 TEMPLE AVENUELONG BEACH, CA 90806-2213
T: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
12 may 2016
1 of 65
hanjip restaurant| DtLa
hanjip restaurant
LIGHTING DESIGN ALLIANCE, INC.
LOS ANGELES2830 TEMPLE AVENUELONG BEACH, CA 90806-2213
T: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting FiXtURE SChEDULE
2 of 65
hanjip restaurant| DtLa 12 may 2016
hanjipLos angeles, CaLDa #15-185.00
LiGhtinG FiXture sCheDuLe5/12/2016
type DesCriptiOn LOCatiOn manuFaCturer & CataLOG # LiGht sOurCe Watts LOaD
type Dim type remarKs
Dp1 Decorative pendants over aisles throughout WAC LightingPD-52214-BR LED 14 W LED DiM
Dp2 Large decorative pendant at lounge area
Lounge WAC LightingQMP-LED311/12-MR LED 60 W LED DiM
Dp3 Decorative pendants at bar counter Bar WAC LightingQMP-LED311/1-MR LED 5 W LED DiM
Dp4 Decorative surface mount fixture at restrooms
Restrooms oXYgEn Lighting3-693-2-30 LED 16 W LED DiM
Dp5Decorative surface mount fixture at restrooms
Restrooms george KovacsP981-077-L LED 40 W LED DiM
DW1 Wall sconce at dining area Dining WAC LightingWS-12713-Pn LED 6 W LED DiM
DW2Wall sconce at restrooms Restrooms WAC Lighting
WS-6111-gL LED 16 W LED DiM
DW3Wall sconce at hallway hallway Rich Brilliant Willing
Monocle Flat Mn-3 LED 8.7 W LED DiM
FD1
Surface mounted 1X4 LED luminaire with integral 0-10V dimming driver, 3000 lumen output, 3500K color temperature.
Boh LithoniaALLS4-30L-EZ1-LP835
3500K LED
30W LED 0-10V
GD1
in-grade LED column uplights at entrance, with cross hatch louver accessory
Exterior Columns
LumascapeLS853LED-14h6-X-[CoVER]-[CABLE]-n-29-Q-[VoLt]-LS6012
3000K LED
14 W LED 0-10V
jD1
Adjustable monopoint with 2700K field changeable LED source and integral angled glare shield, suitable for wet/damp/dry locations.
Dining tables BK LightingMn-LED-e67-SP-[finish]-12-11-A-360SL
2700K LED
7 W LED MLV
rD1 no longer used.
rD2
2 in. recessed LED downlight at kitchen counter, 2700K LED source .
Kitchen gothamiCo ADJL 27/07 [trim Color] [trim Style] [Finish] 6070D [Voltage] UgZ
2700K LED
10 W LED 0-10V
rD36 inch recessed LED downlight at kitchen. integral driver, 2700K color temperature
Kitchen dmf LightingDRD2M10927-MoDE CLEAR LEnSE
2700K LED15 W LED 0-10V
rD4
Recessed 2X2 LED luminaire with integral 0-10V dimming driver, 3300 lumen output, 3500K color temperature.
Boh Lithonia2ALL2-33L-EZ1-LP835
3500K LED
29W LED 0-10V
sD1Linear LED tape light PoS optic Arts
FLEXSiDE-40-27-24-29-XX2700K LED
2.9 W/ft LED 0-10V
sD2LED linear task light PoS & Bar Feelux
tUn-27K-St-StD-S-[length]2700K LED
5 W/ft LED 0-10V
sD3
Linear LED uplight at skylight, 2700K color temperature.
Skylight EcosenseLCiS-[length]-27-120-120
2700K LED
4.5 W/ft LED 0-10V
sD4Low profile linear LED wall grazer,2700K color temperature.
throughout tokistartLXWg-2700-XX
2700K LED6 W/ft LED 0-10V
sD5LED tape light at bar die, 2700K color temperature.
Bar WAC LightingLED-tX2427-[length]-Wt
2700K LED4 W/ft LED ELV
sD6LED linear strip light to light up the parapet
Façade tokistarLUM-50-iW
2700K LED2.88 W/ft LED DiM
tD1Adjustable LED track heads at bar area, 2700K LED light source
Bar Junot255LED-27-D-[beam]-[finish]
2700K LED45 W LED ELV
tD2Low profile track at bar area Bar Juno
t8[finish]2700K LED Per title 24,
allow 45 W per ft
ZD1LED panel for backlit Soju Wall Soju Wall EoS Light Panel System 4000K LED
6 W/ft LED MLV
FiXtURE notES:1. Fixtures shall include all accessories for installation as required by national or local electrical codes.2. Electrical Engineer to determine all fixture voltages.3. Electrical Engineer shall be responsible for emergency lighting, calculations and circuiting to meet code conformance as required by law.4. Prior to the release of the lighting fixture order, the party responsible for fixture procurement (typically the Contractor) shall: -Verify all fixtures shall have appropriate UL, EtL or other recognized and accepted testing agency for dry, damp, or wet location installation as required by national or local electrical codes-Verify all integral or remote ballasts or drivers are recognized by UL, EtL or other recognized testing agency. Remote ballasts or drivers shall be listed as an “assembly” to operate with the luminaire-Verify fixture and ballast configuration conform with title 24 or other energy codes (e.g. tandem wiring, ballast factor, etc)-Work with the Contractor to verify items outlined in section 5 below.5. Prior to the release of the lighting fixture order, contractor shall work with the lighting procurement agent to:-Verify fixture location and above-ceiling clearances for recessed fixtures. Contractor shall notify the Lighting Designer of any conflicts.-Verify final fixture voltage-Verify ceiling trim compatibility (e.g. gyp. or suspended ceiling)-Verify field lengths of cove or perimeter lighting. these fixtures must not be dimensioned from plans-identify fire rated ceiling or floor assemblies and provide fire rated enclosures for fixtures to be installed in these conditions-identify insulated ceiling areas and provide iC rated housing options for fixtures to be installed in these conditions. Contractor shall notify the Lighting Designer if an iC option is not available for the specified fixture(s).6. Lamps or LED light engines shall be installed as outlined in the fixture schedule below. 7. Ceiling thicknesses in excess of 3/4" shall be identified in writing by the Architect or Contractor.8. Walls directly illuminated (e.g. “wall grazing” or perimeter lighting systems) shall be a Level 5 finish, as defined in gypsum Association gA 216-96. 9. the Architect and Lighting Designer shall approve fixture substitutions prior to bid, in accordance with section 26 00 00 specifications. if non-specified or non-approved alternates are installed, they shall be replaced at the Contractors sole expense (including backcharges by other trades such as drywall, painting, etc.), with no additional cost to the owner. 10. Contractor or Purchaser to supply all necessary parts, pieces and mounting brackets as necessary for a fully functioning and properly installed fixture. Refer to detail drawings for additional comments.11. All LED remote power supplies:-to be mounted in an accessible, concealed, dry, well ventilated location, within manufacturer recommendations and distance-All fixtures on a control zone to have equal length wire to the power supply.-Contractor to provide fully code compliant LED system, Contractor to coordinate any necessary additional parts or enclosures (such as nEMA rated enclosures) for the power supply and fixtures to be code compliant.12. DiMMing tYPE: a. non: Standard dimmer module Module configured to function as non-Dim b. inC: incandescent, halogen, or Mark 10 type fluorescent, 2-wire, Forward Phase dimming module c. MLV: Magnetic Low Low Voltage, 2-wire, Forward Phase dimming module d. ELV: Electronic Low Voltage, 2-Wire, Reverse Phase dimming module e. hi-Lume: 3-wire, Specialized Dimming Module for use with Lutron hi-Lume 1% dimming ballasts f. 0-10V: 4-Wire 0-10V Dimming Module with switched mains power and 0-10V low voltage intensity control g. RLY: Relay Module, 2-wire switch closure, no dimming capability h. non+DMX: Fixture requires normal non-dim switched mains power in ADDition to serial data DMX signal from lighting control system i. DiM: Dimming requirements are not known. Dimmer types to be determined by lamp and / or ballast /driver/power supply combinations selected by interior Designer/Architect.
Lighting DESign ALLiAnCE2830 tEMPLE AVEnUE Long BEACh, CA 90806-2213t: 562.989.3843 F: 562.989.3847 www.LightingDesignAlliance.com 1 of 2
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
3 of 65
hanjip restaurant| DtLa 12 may 2016
Dp1
Fixture Type:
Catalog Number:
Project:
Location:
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. FEB 2015
waclighting.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
FLAIR – model: PD-52214dwelLEDTM LED Pendants
PRODUCT DESCRIPTION
Silky smooth curves round out an impeccable design with lustrous plated finishes. The Flair pendant has a white interior for true-white inter-reflected light and the powerful LEDs are shielded with a mouth blown etched opal diffuser for a finished look from any viewing angle. Use in multiples to reveal a wide wash of light over a conference table, dining area or kitchen island.
FEATURES
• Mouth blown and etched opal LED shield• Integral swivel for sloped ceilings• Three 12 inch and one 6 inch rods included (additional extension rods available)• Supplied with 10 feet of wire• Meets 2013 California Title 24 Efficiency• Smooth and continuous ELV dimming • ETL & cETL damp location listed• Driver located in J box• Color Temp: 2700K• 90 CRI• 277V available (special order)
SPECIFICATIONS
Construction: Aluminum
ORDERING NUMBER
Model# Watt LED Lumens Delivered Lumens Finish
PD-52214 14W 906 435BOBNBR
Brushed BronzeBrushed NickelBrushed Brass
PD-52214 -
Example: PD-52214-BNFor 277V, add an “F” before the finish: PD-52214F-BN
Max 53"
9"
14"
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
4 of 65
hanjip restaurant| DtLa 12 may 2016
Dp2
Fixture Type:
Catalog Number:
Project:
Location:
WAC Lightingwww.waclighting.comPhone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive • Port Washington, NY 11050Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Avenue • Ontario, CA 91760Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. May 2014
GENESIS – model: QMP-LED311LED Multi-Light Pendants
PRODUCT DESCRIPTION
With dual uplight and downlight LED engines, Genesis integrates high performance with ambient lighting. An evolutionary design in a diminutive size resulting in a stunning decorative accent.
3n"
3v"
144"max
FEATURES
• All socket sets include 144" wire that may be cut in the field• Free of projected heat, ultraviolet and infrared radiation• 50,000 hour rated life• Replaceable LED module• 5 year WAC Lighting product warranty• UL & CUL Listed
QMP – LED311 / – MR
Example: QMP-LED311/3-MR
FIXTURE PERFORMANCE
Watts Lumens Efficacy9W* 210 per fixture 23.3 Lm/W*
*For QP models power consumption may vary depending upon the efficiency of the power supply being used.
SPECIFICATIONS
Construction: Fixture– Die-cast aluminum, glass ball and glass lens. Canopy– Steel with mirror.
Light Source: 3000K warm white LED, CRI: 85. Replacement module available.
Dimming: May be dimmed to 15% with electronic low voltage (ELV) dimmer.
Finish: Available in electroplated Brushed Nickel (BN).
Standards: UL and CUL Listed.
ORDER NUMBER
Model Canopy FinishQMP-LED311-MR 1-Light
MirrorQMP-LED311/3-MR 3-LightQMP-LED311/6-MR 6-LightQMP-LED311/12-MR 12-Light
Each model includes complete pendant, Quick Connect™ mirror canopy and 12 feet of cable per pendant.
6"
42"
1w"
9"
24"
11w"
1w"
"24" 1w"
20d"
188"15"
17"
24" 1w"
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
5 of 65
hanjip restaurant| DtLa 12 may 2016
Dp3
Fixture Type:
Catalog Number:
Project:
Location:
WAC Lightingwww.waclighting.comPhone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive • Port Washington, NY 11050Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Avenue • Ontario, CA 91760Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. May 2014
GENESIS – model: QMP-LED311LED Multi-Light Pendants
PRODUCT DESCRIPTION
With dual uplight and downlight LED engines, Genesis integrates high performance with ambient lighting. An evolutionary design in a diminutive size resulting in a stunning decorative accent.
3n"
3v"
144"max
FEATURES
• All socket sets include 144" wire that may be cut in the field• Free of projected heat, ultraviolet and infrared radiation• 50,000 hour rated life• Replaceable LED module• 5 year WAC Lighting product warranty• UL & CUL Listed
QMP – LED311 / – MR
Example: QMP-LED311/3-MR
FIXTURE PERFORMANCE
Watts Lumens Efficacy9W* 210 per fixture 23.3 Lm/W*
*For QP models power consumption may vary depending upon the efficiency of the power supply being used.
SPECIFICATIONS
Construction: Fixture– Die-cast aluminum, glass ball and glass lens. Canopy– Steel with mirror.
Light Source: 3000K warm white LED, CRI: 85. Replacement module available.
Dimming: May be dimmed to 15% with electronic low voltage (ELV) dimmer.
Finish: Available in electroplated Brushed Nickel (BN).
Standards: UL and CUL Listed.
ORDER NUMBER
Model Canopy FinishQMP-LED311-MR 1-Light
MirrorQMP-LED311/3-MR 3-LightQMP-LED311/6-MR 6-LightQMP-LED311/12-MR 12-Light
Each model includes complete pendant, Quick Connect™ mirror canopy and 12 feet of cable per pendant.
6"
42"
1w"
9"
24"
11w"
1w"
"24" 1w"
20d"
188"15"
17"
24" 1w"
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
6 of 65
hanjip restaurant| DtLa 12 may 2016
Dp4
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
7 of 65
hanjip restaurant| DtLa 12 may 2016
Dp4
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
8 of 65
hanjip restaurant| DtLa 12 may 2016
Dp5
Product depicted on this spec sheet is protected by United States Federal and/or State laws including US Patent, trademark and/or Copyright and unfair competition laws. Unauthorized reproduction or use carries severe legal penalties.
Job name:
Job type:
Quantity:
Family: hidden gemsProduct Category: Flush Mountitem#: P981-077-LFinish: ChromeCertification: 3195125
LampingLight type: L-Md-C9620b-40wSocket type: LedMax Wattage: 40LED included: YDimmable: YCRi: 84Color temp: 3000initial Lumens: 3482.800Delivered Lumens: 2077.000Rated Life hours: 30000Photo Cell included: n/ABallast: n/A
ShippingCarton Weight: 24.11Carton Width: 27Carton height: 11.5Carton Length: 27Carton Cubic Feet: 4.852Master Pack: 1Master Pack Weight: n/AMaster Pack Width: n/AMaster Pack height: n/AMaster Pack Length: n/AMaster Cubic Feet: n/A*Multi-Pack: n/ASmall Package Shippable: Y
*For additional information, please contact Customer Care: 1-800-221-7977.
MeasurementsWidth: 23.75height: 7Length: 23.75Min overall height: n/AMax overall height: n/Aheight Adjustable: n/AExtension: n/Anet Weight: 18.32Back Plate/Canopy Width: 16.13Back Plate/Canopy height: 1.5Canopy Length: 16.13Center to top of Fixture: n/ACenter to Bottom of Fixture: n/ASlope: n/AChain Length: n/AWire Length: 7
Shade*Shade Description: Laser-Cut Metal Shade*Shade Material: glass (Crystal Strands)*Shade Quantity: 1*Shade number: Pg980*Shade Width: 0.5*Shade height: 4.5*Shade Length: 0.13
MiscellaneousSafety Cable included: n/A
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
9 of 65
hanjip restaurant| DtLa 12 may 2016
DW1
Fixture Type:
Catalog Number:
Project:
Location:
waclighting.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. FEB 2015
MYTHICAL – model: WS-127dwelLEDTM LED Wall Sconce
PRODUCT DESCRIPTION
A simple modern design that features a solid crystal block illuminated from within the frame that creates magnificent sparkles as the bubbles within catch the light. Polished Nickel fittings and concealed hardware complete this curiosity inspiring sconce.
FEATURES SPECIFICATIONS
• ADA compliant• Meets 2013 California Title 24 Efficiency• Smooth and continuous ELV dimming• No driver or transformer needed• ETL & cETL damp location listed• 80,000 hour rated life• Color Temp: 3000K• 90 CRI• 277V available (special order)
• Construction: Steel with solid crystal & seeded bubbles
ORDERING NUMBER
Model# Length Watt LED Lumens Delivered Lumens Finish
WS-12713 13" 5.5W 415 70
PN Polished NickelWS-12718 18" 10.5W 830 140
WS-12724 24" 10.5W 830 160
- PN
Example: WS-12718-PNFor 277V, add an “F” before the finish: WS-12718F-PN
52” 52” 62”24” 24” 24”
13”
18”
24”
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
10 of 65
hanjip restaurant| DtLa 12 may 2016
DW2
Fixture Type:
Catalog Number:
Project:
Location:
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUG 2015
waclighting.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
SOHO – model: WS-61dwelLEDTM Vanity
PRODUCT DESCRIPTION
A clean, simple design, Evo evokes minimalist geometric styling. Cylindrical etched opal glass adorns hardware featured in stunning metal plated � nishes. Mounts vertically or horizontally for a broad range of interior applications, including a vanity light in a powder room or a sconce in a hallway of a � ne home.
FEATURES SPECIFICATIONS
• Etched opal glass• Vertical or horizontal mount• ETL & cETL damp location listed• ADA compliant• Smooth and continuous ELV dimming• Conversion plate for 4 inch Jbox included• Transformer located in J box• 90 CRI • 277V available (special order)• 2700K (3000K and 3500K available as special order)• 50,000 hour rated life• 5 year warranty
Construction: Durable die-cast aluminum hardwares, with thick opal glass.
Light Source: LED
Standards: ETL & cETL Damp location listed, ADA Compliant
WS – –
Example: WS-6117-GLFor 277V special order, add an “F” before the � nish: WS-6117F-GLFor alternate color temperature, special order adding 30 or 35: WS-6117-30-GL
WattLED
LumensDeliveredLumens Finish
3a"
114"
34"
11" WS-6111 16W 700 520
BNCHGL
Brushed NickelChromeGold Plated
3a"
174"
34"
17" WS-6117 25W 1170 860
3a"
238"
34"
23" WS-6123 33.5W 1597 1245
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
11 of 65
hanjip restaurant| DtLa 12 may 2016
DW3
MonocleFlat
Shown: MN-4 (Black)
Product CodesSKU FinishMN-1 NaturalMN-3 GoldMN-4 Black
SpecificationLine voltage LED2700K min 80 CRI8.7 Watts700 Lumens120V Input 50/60Hz (US & CAN)220V Input 50/60Hz (Optional)
DimmingTriac Dimming 5-100%Recommended Wall Switch Lutron DVCL-153P
Optional I/O Wall AdapterMN-WA on/off switch (hard wired) optional 4' flex cord w/plug(no junction box necessary)
Dimensions5.25 Dia x 4 in Depth13 Dia x 10 cm Depth
Product Weight2.5 lb. / 1.14 kg.
Packaging 7 x 7 x 7 in H18 x 18 x 18 cm H
Packaging Weight3.0 lb. / 1.63 kg.
Year of Design2013
DescriptionLED sconce
Country of ManufactureUSA
MaterialsAnodized aluminum, fabric cord,molded plastic
CertificationADA CompliantDamp location
For 2D & 3D drawings of all products, including CAD, Revit and IES files, please visit www.RichBrilliantWilling.com/downloads. 52
37 W 20th StreetSuite 707New York NY 10011T +1 212 388 [email protected]
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
12 of 65
hanjip restaurant| DtLa 12 may 2016
FD1
ALLS41' X 4'
Surface LED
Patents Pending
LED ALLS4-1X4
Specifications
Length: 48 (121.9)
Width: 12-1/4 (31.1)
Height: 4-3/4 (12.1)
All dimensions are inches (centimeters) unless otherwise indicated.
H
W
FEATURES & SPECIFICATIONSINTENDED USE — The AL series surface mount combines clean, fine lines with a unique design that complements any space. The completely luminous optical system provides a concave visual appearance while providing high fixture performance and even illumination. AL is also available with a number of control options thus providing the ability to dim or control the lighting providing the ability to save energy and operate with multiple control systems including daylight or occupancy sensors. CONSTRUCTION — Rugged, one-piece cold-rolled steel reflector assembly with embossed steel for increased structural integrity and strength. Polyester powder-paint after fabrication. Hinged doorframe assembly retains optical assembly and easy access to electrical components.OPTICS — Luminous optical system consists of a high performance transmittance diffuser coupled with a concave, clear, ribbed refractor for and unique multi-step appearance. To improve fixture performance and eliminate pixilation the diffuser uses a unique blend of high molecular weight polymer beads with unrelated refractive index. ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality of illumination for extended service life. 90% LED lumen maintenance at 60,000 hours (L90/60,000).nLight® embedded controls make each luminaire addressable - allowing it to digitally communicate with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply connect all the nLight enabled control devices and the AL luminaires using standard Cat-5 cabling. Unique plug-and-play convenience as devices and luminaires automatically discover each other and self-commission.Lumen Management: Unique lumen management system (option N80) provides onboard intelligence that actively manages the LED light source so that constant lumen output is maintained over the system life, preventing the energy waste created by the traditional practice of over-lighting.Step-level dimming option allows system to be switched to 50% power for compliance with common energy codes while maintaining fixture appearance.eldoLED driver options deliver choice of dimming range, and choices for control, while assuring flicker-free, low-current inrush, 89% efficiency and low EMI.Driver disconnect provided where required to comply with US and Canadian codes.INSTALLATION — Surface mounting. Suitable for damp location.Maintenance: LED boards include plug-in connectors for easy replacement or servicing. LISTINGS — CSA Certified to meet U.S. and Canadian standards. DesignLights Consortium® (DLC) qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified.WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspxNote: Actual performance may differ as a result of end-user environment and application.All values are design or typical values, measured under laboratory conditions at 25 °C.Specifications subject to change without notice.
ALLS4
Series Lumens1 Voltage Driver Color temperature Control Options
ALLS4 Surface LED 1x4
20L 2000 lumens
30L 3000 lumens
40L 4000 lumens
48L 4800 lumens
60L 6000 lumens
(blank) MVOLT(120 - 277V)
347 347V2
EZ1 eldoLED dims to 1% (0-10 volt dimming)
EZB eldoLED dims to dark (0-10 volt dimming)
EDB eldoLED DALI3
EXB eldoLED DMX/RDM3
EXA1 Dims to 1%, XPoint wireless enabled3, 4
EXAB Dims to dark, XPoint wireless enabled3, 4
SLD Step-level dimming3
LP830 3000 KLP835 3500 KLP840 4000 KLP850 5000 K
(blank) No controlsN80 nLight with 80% (L80)
lumen managementN80EMG nLight with 80% (L80)
lumen management for use with generator supply EM power
N100 nLight without lumen management
N100EMG nLight without lumen management for use with generator supply EM power
EL7L 700 nominal lumen battery pack5
EL14L 1400 nominal lumen battery pack5
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: ALLS4 48L EZ1 LP835 N100
Notes
1 Approximate lumen output.
2 Not available with EL7L or EL14L battery packs or SLD driver.
3 Not available with N80, N80EMG, N100, or N100EMG.
4 Gateway not included. Requires on-site commissioning. Visit www.lightingcontrols.com/XPointWireless for more information.
5 Not available with 48L or 60L options.
Catalog Number
Notes
Type
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
13 of 65
hanjip restaurant| DtLa 12 may 2016
ALLS4 Architectural Lighting 1'x4'
ALLS4-1X4
LED: One Lithonia Way, Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2013-2015 Acuity Brands Lighting, Inc. All rights reserved. Rev. 05/12/15
PHOTOMETRICS
12.25
48.02
2.74 42.551.25
9.75
10.19
3.50
2.25
MOUNTING DATAPerformance Data
Lumen Package Lumens Input Watts LPW
20L LP830 2,216.7 21 105.6
20L LP835 2,264.3 21 107.8
20L LP840 2,280.1 21 108.6
20L LP850 2,359.4 21 112.4
30L LP830 3,158.6 30 105.3
30L LP835 3,226.6 30 107.6
30L LP840 3,249.2 30 108.3
30L LP850 3,362.4 30 112.1
40L LP830 4,066.6 39 104.3
40L LP835 4,154.9 39 106.5
40L LP840 4,184.3 39 107.3
40L LP850 4,331.5 39 111.1
48L LP830 4,818.3 47 102.5
48L LP835 4,922.5 47 104.7
48L LP840 4,956.4 47 105.5
48L LP850 5,130.8 47 109.2
60L LP830 5,454.6 55 99.2
60L LP835 5,572.3 55 101.3
60L LP840 5,610.8 55 102.0
60L LP850 5,807.8 55 105.6
ALLS4 40L EZ1 LP835, 4154.9 delivered lumens, test no. LTL26928P29, tested in accordance to IESNA LM-79.
0° 20°
40°
60°
80°
90°
0°0°0° 90°
180°
300
600
900
1200
1500
Coefficients of Utilizationpf 20%pc 80% 70% 50%pw 70%50%30% 50%30%10% 50%30%10%
119109999183777166615754
119104918172645853484441
119100857363554944403633
116102897970635752474440
11698837262554944393633
11695786656484338343128
11198867668615550464239
11195817061544843393532
11192766455484237343028
RC
R
0123456789
10
Zonal Lumen SummaryZone Lumens % Lamp % Fixture0° - 30°0° - 40°0° - 60°0° - 90°90° - 120°90° - 130°90° - 150°90° - 180°0° - 180°
1230196833484155
0000
4155
29.647.480.6
100.00.00.00.00.0
100.0
29.647.480.6
100.00.00.00.00.0
100.0
CP Summary0° 90
0°5°15°25°35°45°55°65°75°85°90
16551639156714221213974719468246680
16551644154113691171958732497253480
FD1
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
14 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
Specifications
Lamp Source 16 W or 20 W LED□ White (4 300 K typical)■ Warm white (3 000 K typical)■ Blue (470 nm)Other colors by request
RGB
Approved Use Suitable for wet locationsSuitable for use in poured concreteInherently protected
Lumen Maintenance (L70)
>60,000 hrsLimited by TM-21 x6 rule
Control Options 0-10 VPWM
IP Rating IP68
Construction 316 marine grade stainless steel
Installation Types Pre-Installation BlockoutConcrete pour, drive-over & general use applications
Direct BurialLandscapes, planters & special applications(consult factory)
Drive-over With OptiClear™ lens and pre-installation blockout (LS6052-K or LS6052-K-SP)
Static Load Rating 8 140 lb (3 700 kg) with OptiClear™ lens and pre-installation blockout (LS6052-K or LS6052-K-SP)(Load applied to center of glass across a 2" diameter area)
Impact Rating IK10 with OptiClear™ lens
Standard Inclusions Teflon coated cover screwsMicroAntiLeach™ wire entry
Accessories LS6052-K/LS6052-K-SP Pre-installation blockout
Remote Transformers / Power SuppliesOrder separately
Refer to Technical Data sectionfor application specific options
Ambient Operating Temperature
16 W -22 °F to 104 °F (-30 °C to +40 °C)20 W -22 °F to 122 °F (-30 °C to +50 °C)
Surface Temperature ≤113 °F (45 °C)
Photometrics Refer to www.lumascape.com
Any luminaire can become hot - take care with appropriate use and placement
IK10IP68
Ingrade LS853LED
LS853LED with round flush cover
20°20°
360o
PWM DIM0-10 V
OPTIONALOPTIONAL OPTIONAL OPTIONAL
The LS853LED is a full featured, shallow depth ingrade luminaire featuring lumen output and efficacy exceeding metal halide. As an inherently protected luminaire it can be used in interior spaces and immediately adjacent to combustible materials (such as wood decking, etc). Dimming options include 0-10 V and PWM protocols, with various power input options, including 120-277 V. In addition, internal rotation and tilt adjustability ensures the most efficient light delivery can be set according to site conditions.
1300 Industrial Road, Unit #19San Carlos, CA 94070FREE CALL 1-866-695-5862 US & [email protected]
www.lumascape.com C1883US 6 Sep 2013
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
15 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
IngradeLS853LED Pre-Installation Blockout
Why Use LS6052-K Pre-Installation Blockout?The LS6052-K acts as a blockout, and is intended for installation before the luminaire, however it has other special functions. To simplify the installation, every LS6052-K is supplied complete with a 4-way, ¾" PVC junction box, inside which the installer can make all necessary connections, and allows the completion of all wiring even before the luminaire arrives on site. This method also ensures the luminaire itself is not damaged during concreting or other site works. Note: The junction box remains serviceable after installation. To complete the installation, Lumascape provides an IP68 connector, enabling a tool-free final connection from the luminaire to the branch circuit. In addition, this connector is readily detachable, allowing for off-site maintenance.
Why Use LS6052-K-SP Pre-Installation Blockout?The LS6052-K-SP pre-installation kit (order separately) is ideal for use in applications where maximum flexibility for the type and location of branch circuit connections are required or where exact site conditions may be unknown. The LS6052-K-SP is also for use with all applications requiring a color changing or dimmable lighting scheme. For use with the LS6052-K-SP, Lumascape provides the LS853LED complete with 6.5' of factory-installed hookup wire or an SOOW cord (both options include a MicroAntiLeach™ seal). This provides the installer with greater flexibility to determine the type and location of the branch circuit connection. This option is also 100% hard-wired, and does not feature the IP68 detachable couplings for off-site maintenance. All aspects of the luminaire itself are still field serviceable.
Cover Options for Pre-Installation Blockout
Flush covers for pre-installation use special seals and support bushes to ensure static loads up to 8 140 lb (3 700 kg) are properly supported. In order to achieve this drive-over rating, OptiClear™ or GripGlass™ must be used.
Pre-Installation Blockout Round Flush Cover
■ SS316: Polished ■ SS316: Brushed
IP68 Connector & Junction Box
The luminaire is fitted with an IP68 connector, which attaches directly to the cord supplied with LS6052-K, without the use of any tools. The cord is 1.8' (0.56 m) in length, and is factory assembled with a 4 way, ¾" junction box - Remains field serviceable after installation.Not suitable for color changing or dimmable applications.
Connection Type '84' for LS6052-K-SP Pre-Installation Blockout
12.4
8” (3
17 m
m)
Ø6.94”
(176 m
m)
Ø10.33” (262 mm)
Connection Type '82' for LS6052-K-SP Pre-Installation Blockout
Lens Options
Borosilicate GlassIdeal for limited access locations. Not recommended for high traffic pedestrian areas.
OptiClear™ GlassGlass of very high optical purity and load strength. Suitable for walk-over and drive-over applications.
GripGlass™OptiClear™ glass with slip reduction glazing process. Suitable for walk-over and drive-over applications.
Connection Type '85' for LS6052-K Pre-Installation Blockout
½" NPT AdapterThe luminaire is factory-fitted with 6.5' hookup wire. Ensure terminations can be made within this length.For other length options, consult factory.
6.5' SOOW CordFor connection to the branch circuit via junction box (by others) or other approved method.c/w 6.5' SOOW Cord (16/3)
www.lumascape.com C1883US 6 Sep 2013
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
16 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
LS853LED Accessories
LS688Wall wash lens
LS699Wide angle
wall wash lens
LS6013Slatted louver
OR OR
LS6012Cross hatch louver
OR
OPTICAL SYSTEMDescription Beam Code
Adjustable Narrow 14 NR(1)
Adjustable Narrow Medium 25 NMAdjustable Medium 30 ME(2)
Adjustable Linear Horizontal 40 x 20 LH(3)
Adjustable Linear Vertical 20 x 40 LV(3)
(1) Not available for RGB.(2) Recommended for best RGB color mixing.(3) Refer to beam orientation diagram.
LAMPDescription Wattage Color Code
LED 16 W White(4 300 K typ.) 16W4
Warm white(3 000 K typ.) 16H6
Blue(470 nm) 16B4
LED 20 W White(4 300 K typ.) 20W4
Warm white(3 000 K typ.) 20H6
Blue(470 nm) 20B4
RGB 20M4
CONNECTION TYPEDescription Code
IP68 Connector & Junction Box 85(1)
6.5' SOOW Cord 84(2)
½" NPT Adapter 82(2)
(1) Not suitable for color changing or dimmable applications.LS6052-K required - order separately.
(2) LS6052-K-SP required - order separately.
HOUSING DEPTHDescription Code
12.48" (317 mm) 29
WIRE ENTRY LOCATIONDescription Code
Bottom Q
Ingrade LS853LED Pre-Installation Blockout Ingrade
INPUT VOLTAGEDescription Code
120-277 V, 50/60 Hz 09(1)
0-10 V Dimmable Driver, 120-277 V, 50/60 Hz 09-DIM(1)(2)
12-15 V, 60 Hz or 12-24 V DC 13(1)(2)(3)
PWM Dimmable Driver, 12 V, 60 Hz or 12-24 V DC 13-DIM(3)
(1) Not available for RGB.(2) Not available with 16 W module.(3) Requires appropriate transformer.
LS853LED
Product Lamp Lens CoverConnection
TypeOpticalSystem
29
HousingDepth
Q
WireEntry
LocationInput
Voltage
COVERDescription Material Finish Code
Round Flush Cover
Stainless steel
Polished MBrushed N
LENSDescription Code
OptiClear™ Very high optical purity and load strength A(1)
GripGlass™ OptiClear™ with slip reduction glazing process
G(1)
Borosilicate Glass
Ideal for limited access locations X(2)
(1) Suitable for drive-over.(2) Not suitable for drive-over.
LS691Prismatic lens
LS685Linear spreader lens
LED
OR
Other accessory stacking options may be available - consult factory
Stacking and order of accessories
Dimmable Wiring Diagram Reference
Input Voltage LED Color Control Type Wiring Diagram
09-DIM Single Color 0-10 V 1
13-DIM Single Color PWM 6
13-DIM RGB PWM 8,9
www.lumascape.com C1883US 6 Sep 2013
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
17 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
IngradeLS853LED Direct Burial
Why Use Direct Burial?Direct burial installation is ideal for landscaping areas or for special applications where depth is restricted. This type of installation also allows for maximum heat dissipation. The 316 grade Stainless Steel construction of the luminaire performs flawlessly in alkaline and acidic soil types, and is also rated for use in concrete pour applications. Note: This installation type has no option for a pre-installation blockout.
Lumascape provides the LS853LED complete with 6.5' of factory installed hookup wire and ½" NPT adapter, supplied complete with MicroAntiLeach™ seal. This provides the installer with greater flexibility to determine the nature of the branch circuit connection. This connection is also 100% hardwired. All aspects of the luminaire itself remain field serviceable.
Consult factory for application advice prior to using this configuration.
Cover Options for Direct Burial
Use flush covers for installation in fine finished surfaces such as granite and marble. They can also be used in some suspended applications. The flush cover will conceal gaps between the luminaire and the surrounding surface.
Square Flush Cover
■ SS316: Brushed
Recessed Cover
■ SS316: Polished■ SS316: Brushed
Round Flush Cover
■ SS316: Polished■ SS316: Brushed
Use recessed cover for installation in soil, grass, pavers and other uneven surfaces where no cover overhang is desired.
0.98”(25 mm)
Ø6.94”
(176 m
m)
Ø6.94” (176 mm)
Ø9.43” (239 mm) Housing OD
7.09
” (18
0 m
m)
Ø9.43” (239 mm) Housing OD
7.09
” (18
0 m
m)
0.12
” (3
mm
)
0.98”(25 mm)
Ø10.08” (256 mm) Cover OD
Ø6.94”
(176 m
m)
Ø6.94” (176 mm)
0.98”(25 mm)
0.98”(25 mm)
7.09
” (18
0 m
m)
0.98”(25 mm)
Ø9.43” (239 mm) Housing OD
Ø6.94”
(176 m
m)
Ø10
.08”
(256
mm
)
Ø6.94” (176 mm)
0.12
” (3
mm
)
Lens Options
Borosilicate GlassIdeal for limited access locations. Not recommended for high traffic pedestrian areas.
OptiClear™ GlassGlass of very high optical purity and load strength. Suitable for walk-over and drive-over applications.
GripGlass™OptiClear™ glass with slip reduction glazing process. Suitable for walk-over and drive-over applications.
Connection type '82' for 'Direct Burial' housing
½" NPT Adapter
The luminaire is factory-fitted with 6.5' hookup wire. Ensure terminations can be made within this length.
For other length options, consult factory.
www.lumascape.com C1883US 6 Sep 2013
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
18 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
OPTICAL SYSTEMDescription Beam Code
Adjustable Narrow 14 NR(1)
Adjustable Narrow Medium 25 NMAdjustable Medium 30 ME(2)
Adjustable Linear Horizontal 40 x 20 LH(3)
Adjustable Linear Vertical 20 x 40 LV(3)
(1) Not available for RGB.(2) Recommended for best RGB color mixing.(3) Refer to beam orientation diagram.
LAMPDescription Wattage Color Code
LED 16 W White(4 300 K typ.) 16W4
Warm white(3 000 K typ.) 16H6
Blue(470 nm) 16B4
LED 20 W White(4 300 K typ.) 20W4
Warm white(3 000 K typ.) 20H6
Blue(470 nm) 20B4
RGB 20M4
LS853LED
Product Lamp Lens
28
HousingDepth
WireEntry
Location
HOUSING DEPTHDescription Code
7.09" (180 mm) 28
WIRE ENTRY LOCATIONDescription Code
Side NBottom Q
Ingrade LS853LED Direct Burial
COVERDescription Material Finish Code
RecessedCover
Stainless steel
Polished BBrushed H
Round FlushCover
Stainless steel
Polished DBrushed I
Square Flush Cover
Stainless steel
Brushed V
CONNECTION TYPEDescription Code
½" NPT Adapter 82
Cover
82
Connection Type
LS853LED Accessories
LS688Wall wash lens
LS699Wide angle
wall wash lens
LS691Prismatic lens
LS6013Slatted louver
LS685Linear spreader lens
LED
LS636Brass grill
OR
OR
OR
External accessoryUse with recessed covers onlyNot suitable for use in traffic areas
Other accessory stacking options may be available - consult factory
Stacking and order of accessories
LENSDescription Code
OptiClear™ Very high optical purity and load strength A
GripGlass™ OptiClear™ with slip reduction glazing process
G
Borosilicate Glass
Ideal for limited access locations X
INPUT VOLTAGEDescription Code
120-277 V, 50/60 Hz 09(1)
0-10 V Dimmable Driver, 120-277 V, 50/60 Hz 09-DIM(1)(2)
12-15 V, 60 Hz or 12-24 V DC 13(1)(2)(3)
PWM Dimmable Driver, 12 V, 60 Hz or 12-24 V DC 13-DIM(3)
(1) Not available for RGB.(2) Not available with 16 W module.(3) Requires appropriate transformer.
InputVoltage
OpticalSystem
Dimmable Wiring Diagram Reference
Input Voltage LED Color Control Type Wiring Diagram
09-DIM Single Color 0-10 V 1
13-DIM Single Color PWM 6
13-DIM RGB PWM 8,9
LS6012Cross hatch louver
OR
www.lumascape.com C1883US 6 Sep 2013
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
19 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
Ingrade LS853LED Photometrics
PhotometricsPhotometric data is based on test results from a NIST traceable testing lab. IES data is available at www.lumascape.com.Note: No depreciation factor is applied to the data shown.
Illuminance at a Distance
ft Center Beam fc Beam Ø
5 153.3 3 ft
10 38.3 5 ft
15 17 8 ft
25 6.1 13 ft
30 4.3 16 ft
40 2.4 21 ft
50 1.5 27 ft
C 0° C 15° C 30° C 45° C 60° C 75° C 90°
90° 0 0 0 0 0 0 0
100° 0 0 0 0 0 0 0
110° 0 0 0 0 0 0 0
120° 0 0 0 0 0 0 0
130° 12 11 9 7 8 9 11
140° 43 46 50 52 52 48 43
150° 206 204 204 209 210 209 219
160° 881 874 853 849 865 897 923
170° 2495 2463 2439 2435 2452 2489 2554
180° 3832 3832 3832 3832 3832 3832 3832
LS853LED4 300 K
(1)
30° Beam Angle
Power Input 21 W
Lumens 1137
Efficacy 54 lm/W
(1) To approximate warm white data, multiply by 0.84. Refer web site for IES files for all color temperatures.
Beam Orientation for the "LV" optical system
Beam Orientation for the "LH" optical system
Beam Orientations
Polar Candela Distribution
LS853LED4 300 K
(1)
14° Beam Angle
Power Input 17 W
Lumens 959
Efficacy 56 lm/W
C 0° C 15° C 30° C 45° C 60° C 75° C 90°
90° 0 0 0 0 0 0 0
100° 0 0 0 0 0 0 0
110° 0 0 0 0 0 0 0
120° 0 0 0 0 0 0 0
130° 2 3 3 4 3 3 2
140° 18 18 18 18 18 17 16
150° 62 63 64 63 61 57 55
160° 322 326 326 319 300 292 290
170° 3080 3084 3070 3039 2984 2938 2912
180° 10371 10371 10371 10371 10371 10371 10371
ft Center Beam fc Beam Ø
5 414.8 1 ft
10 103.7 3 ft
15 46.1 4 ft
25 16.6 7 ft
30 11.5 8 ft
40 6.5 11 ft
50 4.1 13 ft
(1) To approximate warm white data, multiply by 0.84. Refer web site for IES files for all color temperatures.
LS853LED4 300 K
(1)
25° Beam Angle
Power Input 21 W
Lumens 1265
Efficacy 60 lm/W
C 0° C 15° C 30° C 45° C 60° C 75° C 90°
90° 0 0 0 0 0 0 0
100° 0 0 0 0 0 0 0
110° 0 0 0 0 0 0 0
120° 0 0 0 0 0 0 0
130° 7 5 5 4 4 6 7
140° 23 25 26 25 23 21 22
150° 155 148 146 144 145 145 162
160° 1001 987 961 953 961 964 956
170° 3573 3543 3518 3498 3475 3475 3493
180° 5682 5682 5682 5682 5682 5682 5682
ft Center Beam fc Beam Ø
5 227.3 2 ft
10 56.8 4 ft
15 25.3 7 ft
25 9.1 11 ft
30 6.3 13 ft
40 3.6 18 ft
50 2.3 22 ft
(1) To approximate warm white data, multiply by 0.84. Refer web site for IES files for all color temperatures.
C 0° C 15° C 30° C 45° C 60° C 75° C 90°
90° 0 0 0 0 0 0 0
100° 0 0 0 0 0 0 0
110° 0 0 0 0 0 0 0
120° 0 0 0 0 0 0 0
130° 10 9 8 8 13 21 28
140° 20 21 26 44 82 132 138
150° 89 101 130 199 325 479 541
160° 565 593 697 888 1149 1477 1582
170° 2073 2118 2252 2460 2714 2862 2905
180° 3510 3510 3510 3510 3510 3510 3510
ftCenter
Beam fcBeam W Beam L
5 140.4 2 ft 4 ft
10 35.1 4 ft 7 ft
15 15.6 5 ft 11 ft
25 5.6 9 ft 18 ft
30 3.9 11 ft 22 ft
40 2.2 14 ft 29 ft
50 1.4 18 ft 36 ft
958
1916
2874
3832
C-0º
170º160º
150º
140º
130º
120º
110º
100º
90º
2593
5186
7778
10371170º
160º
150º
140º
130º
120º
110º
100º
90ºC-0º
1421
2841
4262
5682170º
160º
150º
140º
130º
120º
110º
100º
90ºC-0º
878
C-0º C-90º
1755
2633
3510170º
160º
150º
140º
130º
120º
110º
100º
90º
LS853LED4 300 K
(1)
20° x 40° Beam Angle
Power Input 21 W
Lumens 1126
Efficacy 54 lm/W
(1) To approximate warm white data, multiply by 0.84. Refer web site for IES files for all color temperatures.
www.lumascape.com C1883US 6 Sep 2013
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
20 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
Technical Data Wiring Diagrams
NOTE: The above diagrams are intended to show electrical pathways between luminaires and ancillary devices. These diagrams are not intended to show type or color of cord/wire, wire gauge or approved use of the cord/wire supplied with luminaires. Consult the luminaire-specific cutsheet or the factory for detailed specifications.
0-10 Vwall boxdimmer
0-10 V +
0-10 V –
Other0-10 V signal
120-277 V
OR
0-10 VDiagram 1 - 0-10 V Dimming for Line Voltage LED LuminairesPlease note: The use of a GFCI may be required. Consult local wiring rules.
Diagram 6 - 0-10 V Dimming - Low Voltage LED Luminaire on 12-15 V AC or 24 V DC Circuit
PWM DIM
0-10 Vwall boxdimmer
120 V
120-277 V
Other0-10 V signal
OR
LS61330-10 V to PWM
Dimming Signal Converter
LSLED-24V12W277Power Supply
LS-TWM-1/2/3or
LSLED-24V96W277
PWM
PWM +
0-10 V
0-10 V +
12-15 V AC / 24 V DC
(suitable NEMA enclosure required - by others)
NOTE: Dimming behavior of these luminaires is inverted.
Use compatibility table to determine maximum number of luminaires the power supply can support.
www.lumascape.com
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
21 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
Technical Data Wiring Diagrams
NOTE: The above diagrams are intended to show electrical pathways between luminaires and ancillary devices. These diagrams are not intended to show type or color of cord/wire, wire gauge or approved use of the cord/wire supplied with luminaires. Consult the luminaire-specific cutsheet or the factory for detailed specifications.
DMX In DMX Out
12-15 V AC
Com +R G B
LS67100DMX to PWM
Translator
LS-TWM-1/2/3Remote Magnetic
Transformer
LSLED-24V96W277Power Supply
1 unit included with each LS67100
120 V
120-277 V
Diagram 8 - RGB via DMX for Low Voltage LED Luminaire on 12-15 V AC Circuit
PWM DIM
Use compatibility table to determine maximum number of luminaires the power supply can support.
120-277 V
DMX In DMX Out
24 V DC +
Com +R G B
24 V DC
LS67100DMX to PWM
Translator
LSLED-24V96W277Power Supply
1 unit included with each LS67100
Diagram 9 - RGB via DMX for Low Voltage LED Luminaire on 24 V DC Circuit
PWM DIM
Use compatibility table to determine maximum number of luminaires the power supply can support.
www.lumascape.com
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
22 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
Technical Data
Transformers and Power Supplies for Low Voltage LED Luminaires
The following list of transformers and power supplies are for use with luminaires specifically described as being compatible with either 12 V AC (wirewound only) transformers or with 12-24 V DC power supplies. Compatibility will be noted in the ordering code of the luminaire concerned, and will typically be referenced by Voltage Code '13' or '13-DIM'. In the case of '13-DIM' additional components may be required. Refer to the applicable wiring diagram/s.
Compatibility with each transformer or power supply is indicated by the value mentioned, representing the maximum number of luminaires that may be powered from each transformer or power supply. Please note, this does not take into consideration voltage drop or ampacity limits of the branch circuit. For assistance, please contact factory.
Wall Mounted Landscape Lighting Transformers Wall Mounted TransformersClass 2 Power
SupplyDirect Burial Transformer
LS-TWM-1-300 LS-TWM-2-600 LS-TWM-3-900 LS-TWM-50 LS-TWM-100 LS-TWM-150 LS-TWM-250 LSLED-24V96W277 LS-TDB1-300
Input Voltage 120 V, 60 Hz 120 V, 60 Hz 120 V, 60 Hz 120 V, 60 Hz 120 V, 60 Hz 120 V, 60 Hz 120 V, 60 Hz 120-277 V, 50/60 Hz 120 V, 60 Hz
Output Voltage 12/13/14/15 V 60 Hz 12/13/14/15 V 60 Hz 12/13/14/15 V 60 Hz 12 V, 60 Hz 12 V, 60 Hz 12 V, 60 Hz 12 V, 60 Hz 24 V DC 12.5 V, 60 Hz
Wattage 1 x 300 W circuit 2 x 300 W circuits 3 x 300 W circuits 50 W 100 W 150 W 250 W 96 W 300 W
LS853LED, 20 Watt 8 16 24 1
Transformers and Power Supply Compatibility
www.lumascape.com
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
23 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
Technical Data Transformer / Power Supply Specifications
LS-TWM-1-300Magnetic transformer - wall mounted
Input 120 VRating 300 WOutput 12/13/14/15 VOutput Circuits 1Protection Electrostatic shield, magnetic breakerApprovals UL, CULNEMA Rating 3RConstruction Stainless steelDimensions H 17.6" (447 mm) W 6.8" (173 mm) D 6.19" (157 mm)Weight 27 lb (12.3 kg)
LS-TWM-3-900Magnetic transformer - wall mounted
Input 120 VRating 900 WOutput 12/13/14/15 VOutput Circuits 3Protection Electrostatic shield, magnetic breakerApprovals UL, CULNEMA Rating 3RConstruction Stainless steelDimensions H 18.6" (472 mm) W 7.8" (198 mm) D 6.19" (157 mm)Weight 34 lb (15.5 kg)
LS-TWM-2-600Magnetic transformer - wall mounted
Input 120 VRating 600 WOutput 12/13/14/15 VOutput Circuits 2Protection Electrostatic shield, magnetic breakerApprovals UL, CULNEMA Rating 3RConstruction Stainless steelDimensions H 17.6" (447 mm) W 6.8" (173 mm) D 6.19" (157 mm)Weight 29 lb (13.2 kg)
Transformers for Landscape Lighting Applications
LS-TDB1-300Magnetic transformer - direct burial
Input 120 VRating 300 WOutput 12.5 VOutput Circuits 1Protection Circuit breakerApprovals ETL (US and Canada)NEMA Rating 12Construction Reinforced compositeDimensions H 9" (229 mm) W 9" (229 mm) D 7" (178 mm)Weight 8 lb (3.6 kg)
LSLED-24V96W277Electronic DC power supply - wall mounted
Input 120-277 V, 50/60 Hz Rating 96 W / 4 AOutput 24 V DCOutput Circuits 1Approvals CSA, CSA-USLocation Wet locationDimensions H 12.32" (313 mm) W 2.54" (65 mm) D 1.67" (42 mm)Weight 2 lb (0.9 kg)
LSLED-24V12W277Electronic DC power supply - NEMA enclosure required (by others)
Input 120-277 V, 50/60 Hz Rating 12 W / 0.5 AOutput 24 V DCOutput Circuits 1Approvals UL, CUL Recognized, Class 2IP rating IP66Location Wet locationDimensions H 3.35" (85 mm) W 1.42" (36 mm) D 0.91" (23 mm)Weight 0.282 lb (0.1 kg)
Class 2 LED Power Supplies
www.lumascape.com
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
24 of 65
hanjip restaurant| DtLa 12 may 2016
GD1
Technical DataControl Specifications
LS61330-10 V to PWM translator - NEMA enclosure required (by others)
Input 24 V DCRating 96 W maxOutput 4 A maxOutput Circuits 1Approvals UL, CUL Recognized, Class 2IP Rating IP66Dimensions H 5.2" (132 mm) W 1.3" (33 mm) D 1" (25 mm)Weight 0.2 lb (0.1 kg)
LS67100DMX to PWM translator - dry location only
Input 24 V DCRating 4 x 60 W maxOutput 4 x 2.5 A maxOutput Circuits 4Approvals UL, CULIP Rating N/ADimensions H 11.25" (286 mm) W 4.6" (117 mm) D 3.2 (82 mm)Weight 0.5 lb (0.2 kg)
Control Related Equipment
www.lumascape.com
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
25 of 65
hanjip restaurant| DtLa 12 may 2016
jD1
MICRO NITE STAR™
RELEASED
01-28-16DRAWING NUMBER
SUB00092740429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900 www.bklighting.com • [email protected]
PROJECT:
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
1 5/8"
3 3/4"
1 5/8" Dia5 5/8"
3/4"
4 3/8"
LockingO-RingCompressionKnuckle
CATALOG NUMBER LOGIC
Material Blank - Aluminum B - Brass
Series MN - Micro Nite Star™
Finish
Lens Type
Cap Style
Example - MN - LED - e67 - SP - BZW - 12 - 11 - B - 360SL
Optics*
360SL - 360SL™ Rotational Knuckle Mounting System
MN
SP - Spot (Green Indicator) NFL - Narrow Flood (Yellow Indicator) FL - Flood (Blue Indicator)
A - 45° B - 90° C - Flush D - 45° less Weep Hole E - 90° less Weep Hole ( Interior Use Only) ( Interior Use Only)
Option
Shielding 11 - Honeycomb Baffle
12 - Soft Focus Lens 13 - Rectilinear Lens
LED
LED Type
BK No. CCT (Typ.)Input Watts
(Typ.) CRI (Typ.)e67 2700K 7 80e68 3000K 7 80e69 4000K 7 80 e75 Amber (590nm) 7 ~
LM79 DATA *OPTICAL DATAMinimum Rated Life (hrs.)
70% of initial lumens (L70)50,00050,00050,000 50,000
L70 DATA
TYPE:
CATALOG NUMBER:
SOURCE:
NOTES:
B-K LIGHTING
Source LED - ‘e’ Technology with Integral Dimming Driver (25W min. load when dimmed) Designed for use with remote 12VAC BKSSL® transformers. Requires magnetic Low Voltage dimmer
e67 - 7WLED/2.7K e68 - 7WLED/3K
e69 - 7WLED/4K e75 - 7WLED/Amber
Beam Type Angle CBCP Visual IndicatorSpot 20° 3991 Green Dot
Narrow Flood 25° 1887 Yellow DotFlood 30° 1469 Blue Dot
Input Volts InRush Current Dimmable Operation Ambient Temperature12VAC/DC 50/60Hz <1A (non-dimmed) Magnetic Low Voltage Dimmer -10°F-130°F
DRIVER DATA
Powder Coat Color Satin Wrinkle
Bronze BZP BZW
Black BLP BLW
White (Gloss) WHP WHW
Aluminum SAP —
Verde — VER
Aluminum Finish
Machined MAC
Polished POL
MitiqueTM MIT
Brass Finish Premium Finish
ABP Antique Brass Powder CMG Cascade Mountain Granite RMG Rocky Mountain Granite
AMG Aleutian Mountain Granite CRI Cracked Ice SDS Sonoran Desert Sandstone
AQW Antique White CRM Cream SMG Sierra Mountain Granite
BCM Black Chrome HUG Hunter Green TXF Textured Forest
BGE Beige MDS Mojave Desert Sandstone WCP Weathered Copper
BPP Brown Patina Powder NBP Natural Brass Powder WIR Weathered Iron
CAP Clear Anodized Powder OCP Old Copper Also available in RAL FinishesSee submittal SUB-1439-00
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
26 of 65
hanjip restaurant| DtLa 12 may 2016
(133mm)5 1/4" (146mm)
5 3/4"
(51mm)2"
5/8"
1 5/8"(41mm)
3 3/4"(95mm)
(16mm)
1 5/8" Dia(41mm)
(79mm)3 1/8"
Dia.(41mm)
1 5/8"
1 5/8"(41mm)
(41mm)
(41mm)
Dia.
1 5/8"
4 1/2"(114mm)
1 5/8"
3 7/8"(98mm)
(19mm)3/4"
LOCK™ Knuckle
5/8"(16mm)
5/8"(16mm)
Horizontal Rotation(Optional 360SL™ Knuckle)
360 SL™
Mounting: Remote Transformers:
Power Pipe™ Power Canopy™ Tree Strap™ Stems Canopies
Mounting Canopies
UPM™ TR Series Power Pipe UPMRM™
Mounting options: Remote options:
Power Pipe™ TR Series Power Pipe™
Options:
Horizontal Rotation™Optional 360SL™ Knuckle
™
UPMRM™
Accessories (Configure separately)
RELEASED
01-28-16DRAWING NUMBER
SUB00092740429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900 www.bklighting.com • [email protected]
PROJECT:
TYPE:
MICRO NITE STAR™
1 5/8"
3 3/4"
1 5/8" Dia5 5/8"
3/4"
4 3/8"
LockingO-RingCompressionKnuckle
(133mm)5 1/4"(146mm)
5 3/4"
(51mm)2"
5/8"
1 5/8"(41mm)
3 3/4"(95mm)
(16mm)
1 5/8" Dia(41mm)
(79mm)3 1/8"
Dia.(41mm)1 5/8"
1 5/8"(41mm)
(41mm)
(41mm)
Dia.
1 5/8"
4 1/2"(114mm)
1 5/8"
3 7/8"(98mm)
(19mm)3/4"
LOCK™ Knuckle
5/8"(16mm)
5/8"(16mm)
GreenSource Initiative™ Metal and packaging components are made from recycled materials. Manufactured using renewable solar energy, produced on site. Returnable to manufacturer at end of life to ensure cradle-to-cradle handling. Packaging contains no chlorofluorocarbons (CFC’s). Use of this product may qualify for GreenSource efficacy and recycling rebate(s). Consult www.bklighting.com/greensource for program requirements. MaterialsFurnished in Copper-Free Aluminum (Type 6061-T6) or Brass (Type 360).
Body Fully machined from solid billet. Unibody design provides enclosed, water-proof wireway and integral heat sink for maximum component life. Integral knuckle for maximum mechanical strength. High temperature, silicone ‘O’ Ring provides water-tight seal.
KnuckleThe LOCK™ (Locking ‘O’ Ring Compression Knuckle) is comprised of two components. The first is integral to the body and features an interior, machined taper. The second is machined from solid billet and features a second, reverse angle taper. The resultant mechanical taper-lock allows a full 180° vertical adjustment without the use of serrated teeth, which inherently limit aiming. High temperature, silicone ‘O’ Ring provides water-tight seal and compressive resistance to maintain fixture position. Design withstands 73 lb. static load prior to movement to ensure decades of optical alignment. ½” pipe thread for mounting.
Optional 360SL™ additionally provides biaxial source control with 360° horizontal rotation in addition to vertical adjustment.
Cap Fully machined. Accommodates [1] lens or louver media. Choose from 45° cutoff (‘A’ or ‘D’), 5/8” deep bezel with 90° cutoff (‘B’ or ‘E’), or flush lens (‘C’) cap styles. ‘A’ and ‘B’ caps include weep-hole for water and debris drainage. ‘D’ and ‘E’ caps exclude weep-hole and are for interior use only.
LensShock resistant, tempered, glass lens is factory adhered to fixture cap and provides hermetically sealed optical compartment. Specify soft focus (#12) or rectilinear (#13) lens.
BKSSL® Integrated solid state system with ‘e’ technology is scalable for field upgrade. Modular design with electrical quick disconnects permit field maintenance. High power, forward throw source complies with ANSI C78.377 binning requirements. Exceeds ENERGY STAR® lumen maintenance requirements. LM-80 certified components.
Integral, constant current driver. 12VAC/VDC input. 50/60Hz. Proprietary input control scheme achieves power factor correction and eliminates inrush current. Output, over-voltage, open-circuit, and short circuit protected. Inrush current limited to <1A (non-dimming). Conforms to Safety Std. C22.2 No. 250.13-12.
Line dimmable. For use with low voltage dimmer with dedicated neutral conductor. Minimum 25 watt load required for dimming.
OpticsInterchangeable OPTIKIT™ modules permit field changes to optical distribution. Color-coded for easy reference: Spot (SP) = Green. Narrow Flood (NFL) = Yellow. Flood (FL) = Blue.
Remote TransformerFor use with 12VAC remote transformer or magnetic transformers only. B-K Lighting cannot guarantee performance with third party manufacturers’ transformers.
WiringTeflon® coated, 18AWG, 600V, 250° C rated and certified to UL 1659 standard.
Hardware Tamper-resistant, stainless steel hardware. LOCK™ aiming screw is additionally black oxide treated for additional corrosion resistance.
FinishStarGuard®, our exclusive RoHs compliant, 15 stage chromate-free process cleans and conversion coats aluminum components prior to application of Class ‘A’ TGIC polyester powder coating. Brass components are available in powder coat or handcrafted metal finish.
Warranty 5 year limited warranty.
Certification and Listing ITL tested to IESNA LM-79. UL Listed. Certified to CAN/CSA/ANSI Standards. RoHs compliant. Suitable for indoor or outdoor use. Suitable for use in wet locations. Suitable for installation within 4’ of the ground. IP66 Rated. Made in USA.
®Teflon is a registered trademark of DuPont Corporation. ®Energy Star is a registered trademark of the United States Environmental Protection Agency.
SPECIFICATIONS
“A/D” CAP “B/E” CAP “C” CAP
All dimensions indicated on this submittal are nominal. Contact Technical Sales if you require more stringent specifications.
B-K LIGHTING
jD1
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
27 of 65
hanjip restaurant| DtLa 12 may 2016
rD2
Luminaire Type:Catalog Number(autopopulated):
GOTHAM ARCHITECTURAL DOWNLIGHTING | 1400 Lester Road Conyers GA 30012 | P 800.315.4982 | gothamlighting.com
© 2015-2016 Acuity Brands Lighting, Inc. All Rights Reserved. Rev. 02/03/16. Specifications subject to change without notice.PAGE 1 OF 4
ICO-2-ADJL
Gotham Architectural DownlightingLED Downlights
2" Incito®
Adjustable, Lensed
Solid-State Lighting(US and International Patents Pending)
FEATURES
ORDERING IN
FORMATION
OPTICAL SYSTEM• Superior 100% virgin silicone refractive optic enables maximum dimensional
stability and optical transmission with no discoloration over life.• Primary control of distribution occurs in refractive optic allowing for aesthetic
versatility with trim color and finish.• Eleven preset distribution patterns allow designers to achieve various objectives. • 3-Step MacAdam Ellipse.• Self-flanged semi-specular or matte-diffuse lower trim utilized in combination
with a highly transmissive softening lens. • Field interchangeable optics. • Wipe-down precision acrylic lens controls aperture brightness and enables
consistent visual texture.MECHANICAL SYSTEM• Matte black enclosure ensures seamless integration into architecture.• Post-installation vertical tilt and horizontal rotation adjustment possible from
above or below ceiling.• Accommodates 1/2" to 5/8" thick ceilings only.• Full horizontal panning up to 365 degrees.• 0-40° vertical tilt.• Hot aiming below ceiling with indicator.• Install from below architecture standard.• Several additional mounting options available including new construction
mounting pan, Chicago plenum, and Type IC.
• Standard ambient operating temperature: 25 °C. High ambient option available.• Accommodates a wide range of applications including multiple plenum cross
sections and ceiling thicknesses. Consult page 2. • Light engine and driver are accessible from above or below ceiling.• Flangeless trim option includes proprietary Gotham mud ring enabling seamless
integration into drywall applications. Mud ring ships separately.ELECTRICAL SYSTEM• Solid-state LED light engine available in 2700 K, 3000 K, 3500 K or 4000 K
color temperatures. Standard CRI: 80 typical. High CRI option available.• Rated system life of >60,000 hours at 70% output.• 120V TRIAC or ELV dimming and 0-10V dimming standard.• Luminaire accepts parallel and branch circuit control wiring.LISTINGS• Fixtures are UL listed to meet US and Canadian standards; wet location listed.• ENERGY STAR® certified product (750lm, 1000lm, 1500lm versions).WARRANTY• 5-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end user environment and application. All values are design or typical values, measured under laboratory conditions at
25 °C.
EXAMPLE: ICO ADJL 35/10 2AR LSS 20D MVOLT UGZ
Series Color temperature Nominal lumen values1 Aperture/Trim color Trim Style Finish Beam
ICO ADJL 27/ 2700 K30/ 3000 K35/ 3500 K40/ 4000 K
05 500 lumens07 750 lumens10 1000 lumens152 1500 lumens
2AR Clear2PR Pewter2WTR Wheat2GR Gold2WR3 White2BR3 Black
(blank) Self-flanged
FL Flangeless
LSS Semi-specular
LD Matte diffuse
15D 15° beam angle20D 20° beam angle25D 25° beam angle30D 30° beam angle35D 35° beam angle40D 40° beam angle45D 45° beam angle3515D Elliptical 35° x 15° beam angle5020D Elliptical 50° x 20° beam angle5060D Elliptical 50° x 60° beam angle6070D Elliptical 60° x 70° beam angle
Voltage Driver Options
MVOLT4
120277
UGZ5 Universal dimming to 1% (0-10V, 120V TRIAC or ELV)
SF6,7 Single fuseTRW8,9 White painted flangeTRBL9,10 Black painted flangeCP11 Chicago plenumNPP16D6,7 nLight® network power/relay pack with 0-10V dimming.NPP16DER6,7 nLight® network power/relay pack with 0-10V dimming.
ER control fixtures on emergency circuit.
CRI90 High CRI (90+)HAO2 High ambient (40°C)ICAT2 IC/Airtight housing constructionNCH New construction housing
ACCESSORIES order as separate catalog numbers (shipped separately)
OPTC212 Additional optics available for field installationOPTC2 KIT Kit including a field interchangeable optic for each of
the 13 preset beam distribution patterns
HS258 2-5/8" Hole saw
HS234FL 2-3/4" Hole saw for flangeless trim option
AW50 Allen wrench (.050") for adjusting tilt
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
28 of 65
hanjip restaurant| DtLa 12 may 2016
rD2
GOTHAM ARCHITECTURAL DOWNLIGHTING | 1400 Lester Road Conyers GA 30012 | P 800.315.4982 | gothamlighting.com
© 2015-2016 Acuity Brands Lighting, Inc. All Rights Reserved. Rev. 02/03/16. Specifications subject to change without notice. PAGE 2 OF 4
ICO-2-ADJL
2" INCITOAdjustable, LensedSolid-State Lighting
ORDERING NOTES
1. Nominal lumen values at 0° tilt, 30° beam.2. 1500lm not available with ICAT or HAO. 3. Not available with finishes.4. Multi-volt 120-277V. 5. Refer to TECH SHEET 240 for full list of recommended compatible dimmers.
Control system electrical load, and protocol may limit minimum dim level. 6. Device must be remote mounted. Will not be factory installed. Access required
to location of remote mounted device.
7. Must specify 120, 277, or 347V. 8. Not specifiable with WR reflector. 9. Not available with flangeless (FL) trim style. 10. Not specifiable with BR reflector. 11. Above access required. 12. Must specify desired optical distribution from available options in "Beam"
column. i.e. OPTC2 15D or OPTC2 3515D. Includes addtional capture rings.
All dimensions are inches (centimeters) unless otherwise noted.
INSTALL-FROM-BELOW CONSTRUCTION, ALL LUMEN VALUES
RECESSED APPLICATION — MINIMUM CLEARANCE REQUIREMENTS
DIMEN
SIONAL DATA
NOTES
3 3/16 [8.1]
3 3/16 [8.1]
3 3/16 [8.1]
13 15/16 [35.4]
7 1/4 [18.4]MIN PLENUM HEIGHT
ALLOW 12" OFBRANCH CIRCUITON THE ROOM SIDE
CEILING THICKNESS 1/2 [1.3] TO 5/8 [1.6]
APERTURE: 2-1/4 (5.7)CEILING OPENING: 2-5/8 (6.7)OVERLAP TRIM: 3 (7.6)
2 7/16 [6.2]4 11/16 [12.0]
3 15/16 [10.0]
3 7/16 [8.7]
2 7/16 [6.3]
2 7/16 [6.2]
6 3/8 [16.2]
DIMEN
SIONAL DATA
ELECTRICAL
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
29 of 65
hanjip restaurant| DtLa 12 may 2016
rD2
GOTHAM ARCHITECTURAL DOWNLIGHTING | 1400 Lester Road Conyers GA 30012 | P 800.315.4982 | gothamlighting.com
© 2015-2016 Acuity Brands Lighting, Inc. All Rights Reserved. Rev. 02/03/16. Specifications subject to change without notice.PAGE 3 OF 4
ICO-2-ADJL
2" INCITOAdjustable, Lensed
Solid-State Lighting
All dimensions are inches (centimeters) unless otherwise noted.
IC / AIRTIGHT HOUSING CONSTRUCTION / CHICAGO PLENUM CONSTRUCTION
NEW CONSTRUCTION HOUSING, ALL LUMEN VALUES
APERTURE: 2-1/4 (5.7)CEILING OPENING: 2-5/8 (6.7)OVERLAP TRIM: 3 (7.6)
4 11/16 [12.0]4 5/16 [11.0]
14 5/16 [36.4]
17 11/16 [45.0]
9 5/16 [23.7]
APERTURE: 2-1/4 (5.7)CEILING OPENING: 2-5/8 (6.7)OVERLAP TRIM: 3 (7.6)
7 11/16 [19.5]
7 5/16 [18.5]9 5/8 [24.4]
14 9/16 [37.1]
17 11/16 [45.0]
DIMEN
SIONAL DATA
ELECTRICAL
WATTAGE CONSUMPTION MATRIX
LUMENS WATTAGE
500 7
750 10
1000 13
1500 22
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
30 of 65
hanjip restaurant| DtLa 12 may 2016
rD2
GOTHAM ARCHITECTURAL DOWNLIGHTING | 1400 Lester Road Conyers GA 30012 | P 800.315.4982 | gothamlighting.com
© 2015-2016 Acuity Brands Lighting, Inc. All Rights Reserved. Rev. 02/03/16. Specifications subject to change without notice. PAGE 4 OF 4
ICO-2-ADJL
2" INCITOAdjustable, LensedSolid-State Lighting
PHOTOM
ETRY
CRI CCT Multiplier
80
2700K 0.902
3000K 0.951
3500K 1
4000K 1.073
90
2700K 0.78
3000K 0.829
3500K 0.85
4000K 0.878
CONTROLS
nLight® Control Accessories: Order as separate catalog number. Visit www.sensorswitch.com/nLight for complete listing of nLight controls.
WallPod stations Model number Occupancy sensors Model numberOn/Off nPODM [color] Small motion 360°, ceiling (PIR / dual tech) nCM 9 / nCM PDT 9On/Off & Raise/Lower nPODM DX [color] Large motion 360°, ceiling (PIR / dual tech) nCM 10 / nCM PDT 10Graphic Touchscreen nPOD GFX [color] Wide view (PIR / dual tech) nWV 16 / nWV PDT 16Photocell controls Model number Wall Switch w/ Raise/Lower (PIR / dual tech) nWSX LV DX / nWSX PDT LV DXDimming nCM ADCX Cat-5 cables (plenum rated) Model number
10', CAT5 10FT CAT5 10FT J115', CAT5 15FT CAT5 15FT J1
CONSULT GOTHAMLIGHTING.COM FOR PHOTOMETRY.
A
A
B
B
AnPS 80 EZ
nCM ADCX
nCM PDT 9
nPS 80 EZ
nPODM 2P DX
B
C
C
AOPTIONAL
WIRING KEY
BA C
CAT-5e Cable Line Power Low VoltageDimming Wires
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
31 of 65
hanjip restaurant| DtLa 12 may 2016
rD3
DRD2Recessed LED Downlight
Commercial New Construction4”, 6”, 8” Aperture
© 2015 DMF Lighting. All Rights Reserved. Specifications subject to change without notice.
Type:
Date:Project:
Product Code:
Contact:
1118 E. 223rd St. Carson, CA 90745 T: 1.800.441.4422dmf Lighting®
www.dmflighting.comPage 1 of 8 | V-07.23.15
DIMMABLE WARRANTY
50,000 hrs70% lumen
maintenance
TWIST
& LOCK
MULTIPLE
INSTALLATIONS
Frame-in KitMOUNTING FRAME: Die-cast aluminum.
JUNCTION BOX: Galvanized steel. Equipped with (4) 1/2” and (2) 3/4” knockouts with pryout slots to allow straight conduit runs. Approved for 8 (four-in, four-out) #12 AWG 90 through wire conductors.
MOUNTING: Butterfly brackets adjust 4” vertically and accept 1/2” EMT, linear flat bars and “C” channels.
CEILING: 1/2” up to 1”.
CUTOUT: 5 1/4” (4” frame-in kit), 7” (6” frame-in kit), 8 9/16” (8” frame-in kit).
Light EngineLED: Tightly binned, high performing white Cree® LEDs enable excellent fixture to fixture color consistency and long lifetime. Delivers 93+ CRI in all available color temperatures.
BINNING: Color variation within 2-step MacAdam ellipse.
CONNECTOR: IDEAL PowerPlug® Luminaire Disconnect, female. Alternate module construction with 0-10V, EcoSystem® dimming and/or Emergency Battery Backup Unit uses a IDEAL PowerPlug® Model 102 connector.
DRIVER: Integral electronic driver for 120/277V 50/60Hz operation. Electronic driver compatible with forward and reverse phase-control dimming at 120V only.
SYSTEM POWER CONSUMPTION: 11.8W (750 Im module), 14.7W (1000 lm module).
DIMMING: TRIAC/ELV dimming standard for 120V only, with flicker-free dimming to less than 5% of total lumen output. Optional 0-10V or EcoSystem® dimming available for 120/277V.
EMERGENCY LIGHTING: Optional Emergency Battery Backup Units available for emergency lighting up to 120 minutes.
RATED LED LIFE: 50,000 hours at 70% lumen maintenance, based on IESNA LM 80-2008 standard (L70, B50).
PHOTOMETRIC TESTING: Tested in accordance to IESNA LM-79-2008.
LISTINGS: cULus Listed. ENERGY STAR® qualified. Title 24 compliant. UL Listed for Wet Location. CEC listed.
WARRANTY: 5 year limited warranty.
TrimCONSTRUCTION: Self flanged, spun aluminum reflector.
FINISHES: White or Alzak® low iridescent reflector with white flange.
• Maximum installation compatibility
• Twist & Lock feature for easy trim installation
• 750 & 1000 lumen outputs
• 2700K, 3000K, 3500K, 4000K CCT
• Flicker-free TRIAC/ELV, 0-10V, or EcoSystem® dimming
• 50,000 hr lifetime at 70% lumen maintenance
• 5 year limited warranty
PRODUCT SPECIFICATIONS
6” application shown
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
32 of 65
hanjip restaurant| DtLa 12 may 2016
DRD2Recessed LED Downlight
Commercial New Construction4”, 6”, 8” Aperture
© 2015 DMF Lighting. All Rights Reserved. Specifications subject to change without notice.
1118 E. 223rd St. Carson, CA 90745 T: 1.800.441.4422dmf Lighting®
www.dmflighting.comPage 2 of 8 | V-07.23.15
PRODUCT SELECTION GUIDE
FRAME-IN KIT Product Code Example: DCDHN4
PRODUCT CODE APPLICATION APERTURE DIMMING
DCDH Housing N New Construction
4 4” Aperture [Blank] TRIAC Dimming (Standard)
6 6” Aperture 7O 0-10V Dimming 750 lm
8 8” Aperture 10O 0-10V Dimming 1000 lm
7C EcoSystem® Dimming 750 lm
10C EcoSystem® Dimming 1000 lm
7TEM TRIAC Dimming w/ Emergency Battery 750 lm
10TEM TRIAC Dimming w/ Emergency Battery 1000 lm
7EM 0-10V Dimming w/ Emergency Battery 750 lm
10EM 0-10V Dimming w/ Emergency Battery 1000 lm
7CEM EcoSystem® Dimming w/ Emergency Battery 750 lm
10CEM EcoSystem® Dimming w/ Emergency Battery 1000 lm
Product Code Example: DRD2M7927LIGHT ENGINE
PRODUCT CODE LUMENS (WATTS) CRI CCT OPTION
DRD2M Module 7 750 lm (11.8W) 9 93+ CRI 27 2700K A Alternate ConstructionUses an IDEAL Model 102 connector for alternate dimming option compatibility; Must be selected if alternate dimming option is selected for frame-in kit
10 1000 lm (14.7W) 30 3000K
35 3500K
40 4000K
TRIM Product Code Example: DCD2TR4SWH
PRODUCT CODE SHAPE APERTURE STYLE FINISH
DCD2T Trim R Round 4 4” Aperture S Smooth WH White
6 6” Aperture AZ Low Iridescent Reflector, White Flange
8 8” Aperture CC Custom
rD3
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
33 of 65
hanjip restaurant| DtLa 12 may 2016
DRD2Recessed LED Downlight
Commercial New Construction4”, 6”, 8” Aperture
© 2015 DMF Lighting. All Rights Reserved. Specifications subject to change without notice.
1118 E. 223rd St. Carson, CA 90745 T: 1.800.441.4422dmf Lighting®
www.dmflighting.comPage 3 of 8 | V-07.23.15
FR AME- IN K IT D IMENSIONS
10"254mm
5116"
128mm
1078"
276mm
7116"
180mm
514"
133mm
538"
137mm
CEILING CUT OUT
TRIM
DCDHN4 4” Commercial New Construction
Frame-in Kit
DCDHN6 6” Commercial New Construction
Frame-in Kit
1134"
298mm 51
16"128mm
111116"
298mm
7"178mm
714"
183mm
7516"
186mm
CEILING CUT OUT
TRIM
1134"
298mm 51
16"128mm
111116"
298mm
7"178mm
714"
183mm
7516"
186mm
CEILING CUT OUT
TRIM
rD3
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
34 of 65
hanjip restaurant| DtLa 12 may 2016
DRD2Recessed LED Downlight
Commercial New Construction4”, 6”, 8” Aperture
© 2015 DMF Lighting. All Rights Reserved. Specifications subject to change without notice.
1118 E. 223rd St. Carson, CA 90745 T: 1.800.441.4422dmf Lighting®
www.dmflighting.comPage 4 of 8 | V-07.23.15
FR AME- IN K IT D IMENSIONS
DCDHN8 8” Commercial New Construction
Frame-in Kit
5116"
128mm 135
16"338mm
13916"
345mm
8916"
217mm
918"
232mm
71316"
198mm
CEILING CUT OUT
TRIM
rD3
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
35 of 65
hanjip restaurant| DtLa 12 may 2016
DRD2Recessed LED Downlight
Commercial New Construction4”, 6”, 8” Aperture
© 2015 DMF Lighting. All Rights Reserved. Specifications subject to change without notice.
1118 E. 223rd St. Carson, CA 90745 T: 1.800.441.4422dmf Lighting®
www.dmflighting.comPage 5 of 8 | V-07.23.15
TR IM D IMENSIONS
3716"
87mm
116"
2mm
21116"
68mm
538"
137mm
31516"
100mm
116"
1mm
21116"
68mm
714"
183mm
434"
120mm
116"
2mm
21116"
68mm
918"
232mm
DCD2TR6 6” Commercial Trim
DCD2TR8 8” Commercial Trim
DCD2TR4 4” Commercial Trim
rD3
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
36 of 65
hanjip restaurant| DtLa 12 may 2016
DRD2Recessed LED Downlight
Commercial New Construction4”, 6”, 8” Aperture
© 2015 DMF Lighting. All Rights Reserved. Specifications subject to change without notice.
1118 E. 223rd St. Carson, CA 90745 T: 1.800.441.4422dmf Lighting®
www.dmflighting.comPage 6 of 8 | V-07.23.15
Delivered Lumen Output (lm)Rated Power (W)Efficacy (lm/W)Color ConsistencyCCT OptionsColor Rendering IndexCRI /R9Lifetime (L70)Max Ambient Operating TemperatureInput Voltage (V)Input Current at 120V (Max)Input Current at 277V (Max)Power FactorTotal Harmonic DistortionDimming
750 1000
11.8 14.7
64 68
2-step SDCM
2700K, 3000K, 3500K, 4000K
93+
60
50,000
40°C
120/277V, 50/60Hz
0.10A 0.13A
0.042A 0.053A
>0.9
<20%
100%-10%
DRD2M7 DRD2M10
DRD2M LED Module
378 "
98mm
1716"
37mm
L IGHT ENGINE OVERVIE W
rD3
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
37 of 65
hanjip restaurant| DtLa 12 may 2016
DRD2Recessed LED Downlight
Commercial New Construction4”, 6”, 8” Aperture
© 2015 DMF Lighting. All Rights Reserved. Specifications subject to change without notice.
1118 E. 223rd St. Carson, CA 90745 T: 1.800.441.4422dmf Lighting®
www.dmflighting.comPage 7 of 8 | V-07.23.15
Light Engine: DRD2M7930 (DRD2 Module, 750 lm, 93 CRI, 3000K)Trim: DCD2TR6SWH (DCD2 Trim, 6” Aperture, Smooth, White)
Zonal Lumen SummaryZone0-300-400-600-900-180
Lumens337.6433.0531.3588.7588.7
Luminaire %57.3%73.6%90.2%100%100%
Values in candela
Gamma0.0º5.0º10.0º15.0º20.0º25.0º30.0º35.0º40.0º45.0º50.0º55.0º60.0º65.0º70.0º75.0º80.0º85.0º90.0º
C 0º
96092488881272358539623917611396806653413020124
Luminous Intensity
LED Module
Flux (lm)
Power (W)
Downlight Spacing
(ft)
Average Illuminance
(fcd)
Max/Min LPD (W/sq ft)
47189.3
DRD2M7 588 11.84x46x68x8
1.231.312.43
0.720.380.18
Calculation Area: 50’(L) x 40’(W) x 10’(H)LLF 1.0, 80/50/20 Reflectance, 2.5’(H) WorkplaneSpacing Criteria: 1.28
Application Reference
C0 - C180 C90 - C270cd 588 lm
Color Temperature Multiplier
*Value based upon testing with 3500, 95CRI. Lumen output of other color temperature can be determined by multiplying the relative lumen factor.
CCT2700K3000K3500K4000K
Relative lumen factor*0.871.001.001.07
105º
90˚
75˚
60˚
45˚
0º 15º 30º
300
450
600
Zonal Lumen SummaryZone0-300-400-600-900-180
Lumens444.3570.0699.3774.9774.9
Luminaire %57.3%73.6%90.2%100%100%
Values in candela
Gamma0.0º5.0º10.0º15.0º20.0º25.0º30.0º35.0º40.0º45.0º50.0º55.0º60.0º65.0º70.0º75.0º80.0º85.0º90.0º
C 0º
96092488881272358539623917611396806653413020124
Luminous Intensity
LED Module
Flux (lm)
Power (W)
Downlight Spacing
(ft)
Average Illuminance
(fcd)
Max/Min LPD (W/sq ft)
482412
DRD2M10 774 14.74x46x68x8
1.221.292.46
0.840.440.21
Calculation Area: 50’(L) x 40’(W) x 10’(H)LLF 1.0, 80/50/20 Reflectance, 2.5’(H) WorkplaneSpacing Criteria: 1.28
Application Reference
Color Temperature Multiplier
*Value based upon testing with 3500, 95CRI. Lumen output of other color temperature can be determined by multiplying the relative lumen factor.
CCT2700K3000K3500K4000K
Relative lumen factor*0.931.001.001.07
105º
90˚
75˚
60˚
45˚
0º 15º 30º
200
300
400
500
600
C0 - C180 C90 - C270 774 lmcd
PHOTOME TRICS
Light Engine: DRD2M10930 (DRD2 Module, 1000 lm, 93 CRI, 3000K)Trim: DCD2TR6SWH (DCD2 Trim, 6” Aperture, Smooth, White)
rD3
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
38 of 65
hanjip restaurant| DtLa 12 may 2016
DRD2Recessed LED Downlight
Commercial New Construction4”, 6”, 8” Aperture
© 2015 DMF Lighting. All Rights Reserved. Specifications subject to change without notice.
1118 E. 223rd St. Carson, CA 90745 T: 1.800.441.4422dmf Lighting®
www.dmflighting.comPage 8 of 8 | V-07.23.15
D IMMER COMPATIB IL IT Y
Recommended Phase-control Dimmers (Dims down to less than 5% nominal measured light output)
*Compatible Phase-control Dimmers (Dims down to less than 20% nominal measured light output)
*Dimmer compatibility reflects performance compatibility only. Please reference your local codes for application.
Brand Series Model Number Max # - loadDRD2M7xx
Max # - loadDRD2M10xx
Control 4 Control 4 C4-APD120 10 9
Cooper Decorator DLC03P, DAL06P 25 20
Legrand Adorne ADPD703TU 35 30
Lutron
Caseta PD-6WCL 12 10
CL series AYCL-153, CTCL-153, DVCL-153, LGCL-153, SCL-153, TGCL-153
12 10
CL series AYCL-253, DVCL-253 20 15
Grafik Eye 3000 QSGR-3P 30 25
Grafik Sys/Homeworks LP-RPM-4U 30 25
Grafik Sys/Homeworks LP-RPM-4A 25 20
Maestro CL MACL-153M, MSCL-OP153M, MSCL-VP153M 12 10
Maestro Wireless MRF2-6ELV, MRF2-6CL 12 10
Brand Series Model Number Max # - loadDRD2M7xx
Max # - loadDRD2M10xx
Cooper Slide SLC03P, SAL06P 25 20
Legrand Harmony H703PTU, HCL453P 30 25
Leviton IllumaTech Slide IPE04 25 20
Lutron
SureSlide 6621, 6674 10 10
Diva DV-600 12 10
Maestro MA-600 12 9
Maestro ELV MAELV-600, MSCELV-600 35 30
Maestro Wireless MRF2-6ND 12 10
Radio RA RRD-6NA, RRD-6CL, RRD-6D 12 10
Skylark S-600, SLV-600 35 30
Skylark S-1000 20 18
Skylark ELV SELV-300 25 20
Ariadni/Toggler AY-603, TG-603 12 10
Power Booster PHPM-PA/PHPM-WBX 25 20
Lightolier Sunrise SR400RPC120, ZP260QEW 20 15
Watt Stopper Dimming Sensor PW-100D 14 12
rD3
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
39 of 65
hanjip restaurant| DtLa 12 may 2016
rD4
LED 2ALL-2X2
Catalog Number
Notes
Type
FEATURES & SPECIFICATIONSINTENDED USE — The AL combines clean, fine lines with a unique design that complements any space. The completely luminous optical system provides a concave visual appearance while providing high fixture performance and even illumination. AL is also available with a number of control options thus providing the ability to dim or control the lighting providing the ability to save energy and operate with multiple control systems including daylight or occupancy sensors. CONSTRUCTION — Rugged, one-piece cold-rolled steel reflector assembly with embossed steel for increased structural integrity and strength. Polyester powder-paint after fabrication. Hinged doorframe assembly retains optical assembly and easy access to electrical components. End plates include integral T-bar clips.OPTICS — Luminous optical system consists of a unique blend of high performance transmittance diffuser coupled with a concave, clear, ribbed refractor for and unique multi-step appearance. To improve fixture performance and eliminate pixilation the diffuser uses a unique blend of high molecular weight polymer beads with unrelated refractive index. ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality of illumination for extended service life. 90% LED lumen maintenance at 60,000 hours (L90/60,000). nLight® embedded controls make each luminaire addressable - allowing it to digitally communicate with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply connect all the nLight enabled control devices and the AL luminaires using standard Cat-5 cabling. Unique plug-and-play convenience as devices and luminaires automatically discover each other and self-commission.Lumen Management: Unique lumen management system (option N80) provides onboard intelligence that actively manages the LED light source so that constant lumen output is maintained over the system life, preventing the energy waste created by the traditional practice of over-lighting.Step-level dimming option allows system to be switched to 50% power for compliance with common energy codes while maintaining fixture appearance.eldoLED driver options deliver choice of dimming range, and choices for control, while assuring flicker-free, low-current inrush, 89% efficiency and low EMI.Driver disconnect provided where required to comply with US and Canadian codes.INSTALLATION — Lightweight and easy to install in any standard T-Bar system.Maintenance: LED boards include plug-in connectors for easy replacement or servicing. Suitable for damp locations.LISTINGS — CSA Certified to meet U.S. and Canadian standards. IC rated.DesignLights Consortium® (DLC) qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified.
2ALL2' X 2'
LED
nLight® Control Accessories: Order as separate catalog number. Visit www.sensorswitch.com/nLight for complete listing of nLight controls.
WallPod stations Model number Occupancy sensors Model numberOn/Off nPODM [color] Standard range 360°, ceiling (PIR / dual tech) nCM 9 / nCM PDT 9On/Off & Raise/Lower nPODM DX [color] Extended range 360°, ceiling (PIR / dual tech) nCM 10 / nCM PDT 10Graphic Touchscreen nPOD GFX Wide view (PIR / dual tech) nWV 16 / nWV PDT 16Photocell controls Model number Cat-5 cable bundles (plenum rated) Model numberContinuous dimming nCM ADC 10', CAT5 10FT CAT5 10FT J1On/Off & Dimming nCM PC ADC 15', CAT5 15FT CAT5 15FT J1
Notes 1 Approximate lumen output.2 Not available with EL7L or EL14L battery packs or SLD driver.3 Not available with N80, N80EMG, N100, or N100EMG.4 Gateway not included. Requires on-site commissioning.
Visit www.lightingcontrols.com/XPointWireless for more information.
Accessories: Order as separate catalog number.
DGA22 Drywall ceiling adaptor , unit installation
Tested to LM80 standards. WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspxNote: Actual performance may differ as a result of end-user environment and application.All values are design or typical values, measured under laboratory conditions at 25 °C.Specifications subject to change without notice.
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: 2ALL2 33L EZ1 LP835 N100
2ALL2
Series Lumens 1 Voltage Driver
2ALL2 Recessed LED 2x2 20L 2000 lumens33L 3300 lumens40L 4000 lumens
(blank) MVOLT (120-277V)347 347V 2
EZ1 eldoLED dims to 1% (0-10 volt dimming)EZB eldoLED dims to dark (0-10 volt dimming)EDB eldoLED DALI3
EXB eldoLED DMX/RDM3
EXA1 Dims to 1%, XPoint wireless enabled3, 4
EXAB Dims to dark, XPoint wireless enabled3, 4
SLD Step-level dimming3
Color temperature Control Options
LP830 3000 KLP835 3500 KLP840 4000 KLP850 5000 K
(blank) No controlsN80 nLight with 80% (L80) lumen managementN80EMG nLight with 80% (L80) lumen management for use with generator supply EM powerN100 nLight without lumen managementN100EMG nLight without lumen management for use with generator supply EM power
EL7L 700 nominal lumen battery packEL14L 1400 nominal lumen battery packCP Chicago plenum
Patent No.: US D680,254 S
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
40 of 65
hanjip restaurant| DtLa 12 may 2016
2ALL2 Architectural Lighting 2'x2'
Specifications
Length: 24 (61.0)
Width: 24 (61.0)
Depth: 3-3/4 (9.5)
2ALL-2X2
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2012-2015 Acuity Brands Lighting, Inc. All rights reserved. Rev. 03/24/15
Constant Lumen ManagementEnabled by the embedded nLight control, the ALL actively tracks its run-time and manages its light source such that constant lumen output is maintained over the system life. Referred to as lumen management, theis feature eliminates the energy waste created by the traditional practice of over-lighting.
0 10 20 30 40 50THOUSAND OPERATING HOURS
0 10 20 30 40 50THOUSAND OPERATING HOURS
POWER INPUT
LIGHTOUTPUT
100%
80%
100%
80%
35W
28W
35W
28W
LIG
HT
OU
TPU
T
LIG
HT
OU
TPU
T
POW
ER IN
PUT
POW
ER IN
PUT
Without Lumen ManagementEnergy is wasted and light level is inconsistent.
POWERINPUT
LIGHT OUTPUT
With Lumen ManagementEnergy is saved and light level remains consistent.
Wasted Energy
Saved Energy
DIMENSIONSAll dimensions are inches (centimeters) unless otherwise specified.
W
D
Performance Data
Lumen Package Lumens Input Watts LPW20L LP830 2,007.3 18 111.520L LP835 2,050.4 18 113.920L LP840 2,064.7 18 114.720L LP850 2,136.5 18 118.733L LP830 3,233.4 29 111.533L LP835 3,303.2 29 113.933L LP840 3,327.8 29 114.833L LP850 3,442.6 29 118.740L LP830 3,809.6 35 108.840L LP835 3,891.6 35 111.240L LP840 3,920.3 35 112.040L LP850 4,057.7 35 115.9
PHOTOMETRICS2ALL2 33L EZ1 LP840, 3327.8 delivered lumens, test no. LTL26921P6, tested in accordance to IESNA LM-79.
0° 20°
40°
60°
80°
90°
0°0°0° 90°
180°
200
400
600
800
1000
1200
Coefficients of Utilizationpf 20%pc 80% 70% 50%pw 70%50%30% 50%30%10% 50%30%10%
119109999183777166615854
119104918172645853484441
119100857363554944403633
116102907970635752474440
11698837262554944393633
11695786656494338343128
11198867668615550464339
11195817061544843393532
11192766555484238343028
RC
R
0123456789
10
Zonal Lumen SummaryZone Lumens % Lamp % Fixture0° - 30°0° - 40°0° - 60°0° - 90°90° - 120°90° - 130°90° - 150°90° - 180°0° - 180°
987158626923328
0000
3328
29.647.780.9
100.00.00.00.00.0
100.0
29.647.780.9
100.00.00.00.00.0
100.0
CP Summary0° 90
0°5°15°25°35°45°55°65°75°85°90
1303129812451125958763555352175410
1303129512371120962779588399219520
rD4
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
41 of 65
hanjip restaurant| DtLa 12 may 2016
sD1
1118 Chestnut Street, Ste 105 Burbank, CA 91506213-250-6069 | [email protected] | www.opticarts.com
Copyright © Optic Arts 2015Optic Arts reserves the right to change this specification without prior notice.03.04.2015
FLEX DC 2.9 SIDE EMITTINGFLEX DC 2.9 projects light parallel to, instead of perpendicular to, the mounting surface. It’s a great choice for bending around curved surfaces when upward or downward projection of light is desired.
• Standard Color Temperatures: 2700k, 3000k, and 6000k. Also available in a variety of solid colors as special order.
• FLEX DC is dimmable via 0-10v, line voltage dimming, or DMX.
• IP67 version is UV resistant
PHYSICALField Cuttable Every 50.0 mm (1.97 in)
Operating Temperature -30º C (-22º F) to +40º C (+104º F)
Environment IP40 Dry LocationIP67 Damp location
Maximum Run Length 33 Feet
Dimensions (W x H) IP40 - 8.5mm (0.33in) x 1.4mm (0.05in)IP67 - 11.0mm (0.43in) x 4.6mm (0.18in)
SERIES IP RATING COLOR TEMP VOLTAGE WATTAGE LENGTH
FLEXSIDE 40 - IP40, Dry Location67 - IP67, Damp Location
27 - 2700k30 - 3000k60 - 6000kR - RedG - GreenB - BlueA - Amber
24 - 24VDC 29 - 2.9 XX - Custom Length
LUMEN OUTPUT2700K 140 lm/ft 48 lm/watt
3000K 142 lm/ft 49 lm/watt
6000K 146 lm/ft 50 lm/watt
PERFORMANCEColor Temperature 2700k, 3000k, 6000k, Red, Green,
Blue, Amber
Lumen Maintenance 50,000 Hours
Binning Tolerance +/-150k
Warranty 3 Years
ELECTRICALInput Voltage 24VDC
Dimming Options MLV0-10 VoltDMXLutron Ecosystem
Power Consumption 2.9 Watts per foot
Wire Size 18AWG, 2 Wire
Certification ETL
PART NUMBER BUILDER
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
42 of 65
hanjip restaurant| DtLa 12 may 2016
1118 Chestnut Street, Ste 105 Burbank, CA 91506213-250-6069 | [email protected] | www.opticarts.com
Copyright © Optic Arts 2014Optic Arts reserves the right to change this specification without prior notice03.04.2015
for use with optic.flexMOUNTING CHANNELSLIM PROFILE
CHS-R-1208 CHS-S-1208 CHS-C-1919
CHS-C-1616 CHS-S-1922S
CHS-R-1715
CHS-S-1715
16.0 mm (0.76in) 19.5 mm (0.76in) 19.5 mm (0.76in)
16.5 mm (0.649in) 16.5 mm (0.649in)
22.0
mm (0
.86in)
21.8
mm (0
.85in)
10.0 mm (0.39in)12.2 mm (0.48in)
17.0 mm (0.67in)
15.3
mm (0
.60in)
Quick Ship - Can usually ship in 3-5 business days
CHS-S-1922R
Material: Anodized Aluminum
Description: Slim and shallow recessed channel.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHS-R-1208-CCCHS-R-1208-CFCHS-R-1208-CM
Accessories:Endcap
End Cap w/hole
CHS-R-1208-ECCHS-R-1208-ECH
Material: Anodized Aluminum
Description: Slim and deep surface mount-ed channel. Eliminates visible LED nodes when used with FLEXDC 3.0 and milky lens.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHS-S-1715-CCCHS-S-1715-CFCHS-S-1715-CM
Accessories:Endcap
End Cap w/hole Mounting Clip
CHS-S-1715-ECCHS-S-1715-ECHCHS-S-1715-MC
Material: Anodized Aluminum
Description: Slim corner mount channel with rounded lens.
Length: 2 meter
Lens Types:Frosted
MilkyCHS-C-1616-CFCHS-C-1616-CM
Accessories:Endcap
End Cap w/holeMounting Clip
CHS-C-1616-ECCHS-C-1616-ECHCHS-C-1616-MC
Material: Anodized Aluminum
Description: Slim surface mounted channel with square wrap around lens. Mounting clip is fully concealed within fixture base.
Length: 2 meter
Lens Types:Milky CHW-S-2219-CM
Accessories:Endcap
End Cap w/holeMounting Clip
CHW-S-2219-ECCHW-S-2219-ECHCHW-S-2219-MC
Material: Anodized Aluminum
Description: Slim surface mounted channel with rounded wrap around lens. Mounting clip is fully concealed within fixture base.
Length: 2 meter
Lens Types:Milky CHW-S-2119-CM
Accessories:Endcap
End Cap w/holeMounting Clip
CHW-S-2119-ECCHW-S-2119-ECHCHW-S-2119-MC
Material: Anodized Aluminum
Description: Slim corner mount channel .
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHS-C-1919-CCCHS-C-1919-CFCHS-C-1919-CM
Accessories:Endcap
End Cap w/holeMounting Clip
CHS-C-1919-ECCHS-C-1919-ECHCHS-C-1919-MC
Material: Anodized Aluminum
Description: Slim and deep recessed channel. Eliminates visible LED nodes when used with FLEXDC 3.0 and milky lens.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHS-R-1715-CCCHS-R-1715-CFCHS-R-1715-CM
Accessories:Endcap
End Cap w/hole
CHS-R-1715-ECCHS-R-1715-ECH
Material: Anodized Aluminum
Description: Slim and shallow surface mount channel.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHS-S-1208-CCCHS-S-1208-CFCHS-S-1208-CM
Accessories:Endcap
End Cap w/holeMounting Clip
CHS-S-1208-ECCHS-S-1208-ECHCHS-S-1208-MC
17.0mm (0.67in)8.0
mm (0
.31in)
8.0mm
(0.31
in)
12.2mm (0.48in)
17.1mm (0.67in) 18.5mm (0.72in) 17.2mm (0.48in)
15.5m
m (0
.60in)
23.3mm (0.91in)
18.5m
m (0
.72in)
12.2mm (0.48in)
23.2mm (0.91in)
16.0
mm (0
.762in
)
sD1
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
43 of 65
hanjip restaurant| DtLa 12 may 2016
1118 Chestnut Street, Ste 105 Burbank, CA 91506213-250-6069 | [email protected] | www.opticarts.com
Copyright © Optic Arts 2015Optic Arts reserves the right to change this specification without prior notice03.03.2015
for use with optic.flexMOUNTING CHANNEL
20.2 mm (0.78in)
30.0mm (1.79in)30
.0mm
(1.79
in)
30.0m
m (1
.79in)
30.0mm (1.79in)
20.2mm (0.78in)
WIDE PROFILE
CHW-S-2010
CHW-R-4435
CHW-C-3030 CHW-C-3030S
CHW-SH-3561
CHW-S-3535
CHW-SH-7532
Quick Ship - Can usually ship in 3-5 business days
35.0mm (1.37in)
31.4mm (1.23in)
39.9m
m (1
.57in)
61.7m
m (2
.42in)
75.0mm (2.95in)
32.0m
m (1
.25in)
64.0mm (2.51in)
44.0mm (1.73in)
35.0mm (1.37in)
35.0m
m (1
.37in)
CHW-SH-2027
20.3mm (0.79in)
27.0m
m (1
.60in)
16.7mm (0.65in)
19.5m
m (0
.76in)
Material: Anodized Aluminum
Description: Low profile surface mounted channel.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHW-S-2010-CCCHW-S-2010-CFCHW-S-2010-CM
Accessories:Endcap
End Cap w/holeMounting Clip
CHW-S-2010-ECCHW-S-2010-ECHCHW-S-2010-MC
Material: Anodized Aluminum
Description: Wide and deep recessed channel. Eliminates visible LED nodes for most FLEXDC tapes when used with a milky lens. Can be securely and conveniently mounted with CHW-R-3535-SC spring clip.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHW-R-3535-CCCHW-R-3535-CFCHW-R-3535-CM
Accessories:Endcap
End Cap w/holeSpring Clip
CHW-R-3535-ECCHW-R-3535--ECHCHW-R-3535-SC
Material: Anodized Aluminum
Description: 45 degree channel with rounded lens.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHW-C-3030-CCCHW-C-3030-CFCHW-C-3030-CM
Accessories:Endcap
End Cap w/holeMounting Clip
CHW-C-3030-ECCHW-C-3030-ECHCHW-C-3030-MC
Material: Anodized Aluminum
Description: Small surfaced mounted or hanging channel with wrap around lens.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHW-SH-2027-CCCHW-SH-2027-CFCHW-SH-2027-CM
Accessories:Endcap
End Cap w/holeHanging Hardware
CHW-SH-2027-ECCHW-SH-2027--ECHCHW-SH-2027-HHK
Material: Anodized Aluminum
Description: Large surface mounted or hanging channel with wrap around lens.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHW-SH-3561-CCCHW-SH-3561-CFCHW-SH-3561-CM
Accessories:Endcap
End Cap w/holeHanging Hardware
CHW-SH-3561-ECCHW-SH-3561-ECHCHW-SH-3561-HHK
Material: Anodized Aluminum
Description: Wide surface mounted or hanging channel.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHW-SH-7532-CCCHW-SH-7532-CFCHW-SH-7532-CM
Accessories:Endcap
End Cap w/holeHanging Hardware
CHW-SH-7532-ECCHW-SH-7532--ECHCHW-SH-7532-HHK
Material: Anodized Aluminum
Description: 45 degree channel with square lens.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHW-C-3030S-CCCHW-C-3030S-CFCHW-C-3030S-CM
Accessories:Endcap
End Cap w/holeMounting Clip
CHW-C-3030S-ECCHW-C-3030S-ECHCHW-C-3030S-MC
Material: Anodized Aluminum
Description: Wide and deep surface mounted channel. Eliminates visible LED nodes for most FLEXDC tapes when used with a milky lens.
Length: 2 meter
Lens Types:Clear
FrostedMilky
CHW-S-3535-CCCHW-S-3535-CFCHW-S-3535-CM
Accessories:Endcap
End Cap w/holeMounting Clip
CHW-S-3535-ECCHW-S-3535--ECHCHW-S-3535--MC
20.0mm (0.78in)
23.5 mm (0.92in)
10.0
mm (0
.39in)
35.0mm (1.37in)
31.0mm (1.22in)
35.0
mm (1
.37in)
sD1
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
44 of 65
hanjip restaurant| DtLa 12 may 2016
1118 Chestnut Street, Ste 105 Burbank, CA 91506213-250-6069 | [email protected] | www.opticarts.com
Copyright © Optic Arts 2015Optic Arts reserves the right to change this specification without prior notice03.03.2015
for use with optic.flexMOUNTING CHANNELWIDE PROFILE
CHW-S-2623 CHW-SH-3030
Material: Anodized Aluminum
Description: Surface mounted channel with wrap around lens.
Length: 2 meter
Lens Types:Milky CHW-S-2623-CM
Accessories:Endcap
End Cap w/holeCHW-S-2623-ECCHW-S-2623-ECH
Material: Anodized Aluminum
Description: Surface mounted or hanging channel.
Length: 2 meter
Lens Types:Milky CHW-SH-3030-CM
Accessories:Endcap
End Cap w/holeHanging Hardware
CHW-SH-3030-ECCHW-SH-3030-ECHCHW-SH-3030-HHK
26.2mm (1.03in) 30.0mm (1.18in)
20.04mm (0.78in)
28.04mm (1.1in)
22.76
mm (0
.89in)
30.0m
m (1
.18in)
sD1
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
45 of 65
hanjip restaurant| DtLa 12 may 2016
for use with optic.flex
PART DESCRIPTIONML10S24VDC 10W EMCOD MLV DIMMABLE DRIVER ML20S24VDC 20W EMCOD MLV DIMMABLE DRIVER ML35S24VDC 35W EMCOD MLV DIMMABLE DRIVERML35S24VDC 277 35W EMCOD MLV DIMMABLE DRIVERML40S24VDC 40W EMCOD MLV DIMMABLE DRIVER ML50S24VDC 50W EMCOD MLV DIMMABLE DRIVER ML50S24VDC 277 50W EMCOD MLV DIMMABLE DRIVERML60S24VDC 60W EMCOD MLV DIMMABLE DRIVERML75S24VDC 75W EMCOD MLV DIMMABLE DRIVERML75S24VDC 277 75W EMCOD MLV DIMMABLE DRIVERML96S24VDC 96W EMCOD MLV DIMMABLE DRIVEREM200S24VDC 200W EMCOD MLV DIMMABLE DRIVER EM300S24VDC 300W EMCOD MLV DIMMABLE DRIVER
FLEX DRIVERS & DECODERS
EMCOD MLV DIMMABLE DRIVERS (20% DIM) JUSTIN MLV DIMMABLE DRIVERS (1% DIM)
HATCH ELECTRONIC NON-DIM DRIVERS - 24VDC 120-277VAC
PART DESCRIPTIONLV60-24N-UNV-K 60W HATCH ELECTRONIC NON-DIM DRIVERLV100-24N-UNV-J 100W HATCH ELECTRONIC NON-DIM DRIVER
PART DESCRIPTIONHLG-80H-24B 80W MEAN WELL ELECTRONIC 0-10V DIM DRIVER - 90-305VAC
MEAN WELL ELECTRONIC 0-10V DIMMABLE DRIVERS - 24VDC IP67
LUTRON Hi-LUME® DIMMABLE DRIVERS - 24VDC
PART DESCRIPTIONLTE A4U1UKL-CV240
LUTRON - 2-wire forward phase control Hi-lume® A-Series Constant Voltage Driver, 24VDC, 120VAC
L3D A4U1UKL-CV240
LUTRON - EcoSystem® Control - Hi-lume® A-Series Constant Voltage Driver, 24VDC, 120 or 277VACCLASS 2
CLASS 2
CLASS 2
4008104
CLASS 2
PART DESCRIPTIONDECLCD.4.DMX 4-CHANNEL DMX INTERFACEDECLCD.3.DMX 3-CHANNEL DMX INTERFACE
DMX DECODERS
1118 Chestnut Street, Ste 105 Burbank, CA 91506213-250-6069 | [email protected] | www.opticarts.com
Copyright © Optic Arts 2014Optic Arts reserves the right to change this specification without prior notice03.03.2015
PART DESCRIPTION481-24DCR 120VAC 48W DIMMABLE DRIVER481-24DCR-277 277VAC 48W DIMMABLE DRIVER481-24DCR-CONN 120VAC 48W DIMMABLE DRIVER
W/ CONNECTORS481-24DCR-277-CONN 120VAC 48W DIMMABLE DRIVER
W/ CONNECTORS961-24DCR 120VAC 96W DIMMABLE DRIVER961-24DCR-277 277VAC 96W DIMMABLE DRIVER
CLASS 2
sD1
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
46 of 65
hanjip restaurant| DtLa 12 may 2016
sD2
LED
FEELUX Lighting, Inc.3000 Northwoods Parkway #115Norcross, GA 30071 U.S.A.Phone: (678) 668 7005
TUN 3 of 3 01/15
Specifications subject to change without notice.All Rights Reserved. © 2015 - Feelux Lighting, Inc.
NORTH AMERICA
PRODUCT FEATUREs• seamless Illumination• Ultra Low, sleek Profile• Line Voltage• Even Illumination on surfaces• Easy Installation• Dimmable with Accessories
• Beam Angle: Asymetric120º • Finish: Natural Aluminum (standard)• Warranty: 5 year Warranty• Certifications
• Voltage: AC 100~240 V• Operating Temperature: 32-113ºF (0-45ºC)• Lamp Life: 40,000 hrs / 70%• Available Color:2700K, 3000K, 3500K, 4000K, • Color Rendering: Ra > 80• Energy Efficiency: 75 Lm/W• Degree of protection IP20
MODEL
TUN
POWER/DIMCOLOR
120V230V
LENs
ST -Milky white S -StraightV -Varies*
TUN ST
ACCEssORIEs
NON
RSWRocker SwitchOCCOccupency Sensor
TUNELight2
CONFIgURATION RUN LENgTH
ft. CP -Cable/PlugHW -Hard WireZT0-10V Interface FP Forward Phase
27K -2700 K30K -3000 K35K -3500 K40K -4000 K
sPECIFICATION DIAgRAM
RUN LENGTHIN FEETFill out for every run section
*DRAWINgs & RUN LENgTH REqUIRED
PRODUCT sPECIFICATIONs
VOLTAgE
3000 Northw
oods Parkway, Suite 115 N
orcross GA
30071
678 - 668 - 7005 • ww
w.FeeluxLighting.com
FEELUX LINE VOLTAGE POWER & FIXTURE CONNECTOR OPTIONS
Power Options Fixture Connector Options
LINE VOLTAGE
Power Cord with Plug
Option 1 - Cord & Plug
Option 2 - Hardwire
Option 3 - Dimming
Fixture (Length)
Direct Connector Flexible Connector
6”,12”,24”,48” or 72"
Fixture (Length) Fixture (Length)
Hardwire Box
MAX Power Load on 1 Power Feed (non-dimming)
Dimming Module
Occupency SensorOPTION
Fluorescent: 600WLED: 400W
MAX Number of Fixtures Dimming
Fluorescent: Need one booster every 10LED: Need one booster every 15
04/2014 | Version: 1
Interface Cable
Interface Cable
OR
+
+
120V System - Other Voltages Available - Consult Factory
FLX stix
sPECIFICATION gUIDE ALL PARTs NEEDED FOR INsTALLATION WILL BE INCLUDED. FOR ADDITIONAL COMPONENTs ORDER sEPARATELy ON PAgE 2
MOUNTINg
STD -Flat Brackets Included
BK1 -SlidingBrackets
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
47 of 65
hanjip restaurant| DtLa 12 may 2016
sD3
ECOSENSELIGHTING.COMEcoSense Lighting Inc.915 Wilshire BoulevardSuite 2175Los Angeles, CA 90017
Specifications subject to change without notice. Visit EcoSenseLighting.com for the most current specifications.
2014 All rights reserved.EcoSense, the EcoSense logo, and EcoSpec are regis-tered trademark of EcoSense Lighting Inc. SPEC-LCIS-20140110-V1
Phone 310-496-6255Fax 310-496-6256Toll Free 855-632-6736 855-6-ECOSEN
1
PERFORMANCE ADDITIONAL INFORMATION ON NEXT PAGE
CCT (K) Optic Lumen Output Efficacy (lm/W)12” 48”
2700K 120°x120° 223 lm/LF 892 lm 52.2lm/W 3000K 120°x120° 249 lm/LF 996 lm 54.6lm/W 3500K 120°x120° 264 lm/LF 1,056 lm 57.3lm/W 4000K 120°x120° 306 lm/LF 1,224 lm 69.9lm/W
* Performance data is from LM-79 and LM-63 testing at typical power input
DATE
PROJ.
FIRM
TYPE
EcoSpec® Linear INT - Standard Power
New Linear Series
OVERVIEW / SPECIFICATION
Color Rendering Index 80+Color Consistency 2 Step MacAdam EllipseLumen Depreciation / Rated Life L70 >60,000 hours @ 25°C*
* Calculations for LED fixtures are based on measurements that comply with IES LM-80 testing procedures and IES TM-21 Calculator.
ELECTRICAL Power Consumption 4.5W/LF Typical (The Typical input power range allows for a +/-10% variation of all components)5W/LF Maximum (All fixtures are labelled with Maximum wattage)
Max Fixture Run Length 140’ (40m) @120VAC; 280’ (80m) @220VAC ; 200’ (60m) @277VACPower Factor 0.90 Operating Voltage 100-120VAC, 220-240VAC, 277VAC, 50/60 Hz (all voltages)Driver Integral to Fixture; De-rated Power and Synchronous Start-up at Full BrightnessStartup Temperature -4°F to 122°F (-20°C to 50°C)Operating Temperature -4°F to 122°F (-20°C to 50°C)Storage Temperature -40°F to 176°F (-40°C to 80°C)
CONTROL Dimming 100-120VAC ELV type, Reverse Phase, Trailing Edge220-240VAC ELV type, Reverse Phase, Trailing Edge277VAC ELV type, Reverse Phase, Trailing Edge120VAC / 277VAC, 0-10V with Linear Dimming Control Module (LDCM)
PHYSICAL Dimensions W 2.0” x H 1.4” x L 12”/48”; (52mm x 35.7mm x 304mm/1,219mm)Housing / Lens Extruded Aluminium; Clear Polycarbonate; Stainless Steel Fasteners
Plastic Endcaps with Plastic/Rubber Overmold for Cable Assembly Weight 0.496lbs. / 0.225kg (1ft) ; 1.61lbs. / 0.73kg (4ft)Connectors Integral Male/ Female 3 Pin Connectors on Pigtail Cable Assembly, IP40 RatedEnvironment Indoor; CE Certified IP40 / ETL Certified for Dry/Damp LocationsBeam Angle Clear Lens: 120°x 120°, Frosted Lens Accessory Available Mounting Options: Integral Adjustable 180° Rotation Brackets
FIXTURE RATING & CERTIFICATIONS
CE, ENEC, C-Tick Certified, CCCETL CertifiedRoHS CompliantEnergy Star
**Energy Star is certified to LCIS-XX-XX-120-120 series.
EcoSense THD/Inrush Current Information: Please contact an EcoSense Lighting sales representative
RoHSCOMPLIANT
• Economical• Simple Installation• In-line Connection• High Efficacy • Integral Driver / AC Power• Dimmable: ELV (RP), 0-10V• Dimming at 120V, 220V, and 277V• Dimming down to 0%• Long Life (L70)
EcoSpec® Linear INT - is designed with a slim profile and integral brackets with 180° vertical rotationadjustability providing versatility making this luminaire ideally suited for interior architectural, hospitality,retail, exhibit, and display applications. Patent-pending dimming technology dims down to 0% outputpower.
Features:
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
48 of 65
hanjip restaurant| DtLa 12 may 2016
sD3
ECOSENSELIGHTING.COMEcoSense Lighting Inc.915 Wilshire BoulevardSuite 2175Los Angeles, CA 90017
Specifications subject to change without notice. Visit EcoSenseLighting.com for the most current specifications.
2014 All rights reserved. EcoSense, the EcoSense logo, and EcoSpec are regis-tered trademark of EcoSense Lighting Inc. SPEC-LCIS-20140110-V1
Phone 310-496-6255Fax 310-496-6256Toll Free 855-632-6736 855-6-ECOSEN
2
DATE
PROJ.
FIRM
TYPE
EcoSpec® Linear INT - Standard Power
New Linear Series
ORDERING Choose the option that best suits your needs and write its corresponding code on the appropriate line to form the product code
LCIS / LCIL - - - - 120
MODEL LENGTH COLOR VOLTAGE OPTICLCIS 12 - 12” 23 - 2300K## 120 - 100-120VAC 120 - 120° x 120°
LCIL# 48 - 48” 27 - 2700K 220 - 220-240VAC
30 - 3000K 277 - 277VAC**
35 - 3500K
40 - 4000K
EXAMPLE: LCIS* - 12 - 27 - 120 - 120 (*Linear Cove Interior Standard Power) LCIL* - 12 - 27 - 120 - 120 (*Linear Cove Interior Low Power) # See Linear INT Low Power Spec Sheet for more details
## See Linear INT Warm Cove Spec Sheet for more details
Wiring Options*INT Leader Cable, 3 Pin, 10ft, 110V INT3P-A-LDR-120-10 INT Leader Cable, 3 Pin, 10ft, 220V INT3P-A-LDR-220-10INT Jumper Cable, 3 Pin, 5ft, 110V INT3P-A-JMP-120-05 INT Jumper Cable, 3 Pin, 5ft, 220V INT3P-A-JMP-220-05
INT Jumper Cable, 3 Pin, 1ft, 110V INT3P-A-JMP-120-01 INT Jumper Cable, 3 Pin, 1ft, 220V INT3P-A-JMP-220-01
INT Jumper Cable, 3 Pin, 4in, 110V INT3P-A-JMP-120-4 INT Jumper Cable, 3 Pin, 4in, 220V INT3P-A-JMP-220-4* One (1) Terminator included standard with each leader cable.
One Leader Cable is required per circuit / fixture run. Leader cable has bare leads one end, female connector opposite end. Leader / Jumper cables are not rated for plenum applications.
**The 120VAC cables are also rated for 277VAC use.
Mounting Options Integral, 180° Adjustable Brackets Factory installed with 2 (two) per product length, non-removable
Frosted Lens OptionFrosted Lens, Linear INT, 12in LCI-A-FRLS-12 Snap-on lens before or after mounting fixture.
Frosted Lens, Linear INT, 48in LCI-A-FRLS-48 Snap-on lens before or after mounting fixture.
Control Options100-120VAC / 277VAC Linear Dimming Control Module 0-10V LDCM-120-277-010V-GR
100-120VAC / 277VAC Linear Dimming Control Module 0-10V - Plenum Rated LDCM-PL-120-277-010V-GR
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
49 of 65
hanjip restaurant| DtLa 12 may 2016
sD3
ECOSENSELIGHTING.COMEcoSense Lighting Inc.915 Wilshire BoulevardSuite 2175Los Angeles, CA 90017
Specifications subject to change without notice. Visit EcoSenseLighting.com for the most current specifications.
2014 All rights reserved.EcoSense, the EcoSense logo, and EcoSpec are regis-tered trademark of EcoSense Lighting Inc. SPEC-LCIS-20140110-V1
Phone 310-496-6255Fax 310-496-6256Toll Free 855-632-6736 855-6-ECOSEN
3
DATE
PROJ.
FIRM
TYPE
EcoSpec® Linear INT - Standard Power
New Linear Series
DIMENSIONS For complete dimensions and submittal drawings, please visit: ecosenselighting.com
1.83
46.4
9
2.04752
12.0 48.0 [304] [1219]
1.3534.30TYP.
1.5940.30
TYP.
2.05 52
1.25
31.8
4
1.41
35.7
1
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
50 of 65
hanjip restaurant| DtLa 12 may 2016
sD3
ECOSENSELIGHTING.COMEcoSense Lighting Inc.915 Wilshire BoulevardSuite 2175Los Angeles, CA 90017
Specifications subject to change without notice. Visit EcoSenseLighting.com for the most current specifications.
2014 All rights reserved. EcoSense, the EcoSense logo, and EcoSpec are regis-tered trademark of EcoSense Lighting Inc. SPEC-LCIS-20140110-V1
Phone 310-496-6255Fax 310-496-6256Toll Free 855-632-6736 855-6-ECOSEN
4
DATE
PROJ.
FIRM
TYPE
EcoSpec® Linear INT - Standard Power
New Linear Series
DISTRIBUTIONS
LCIS-XX-XX-XXX-120120° x 120°
60° 60°
120°
60° 60°
120°
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
51 of 65
hanjip restaurant| DtLa 12 may 2016
sD3
ECOSENSELIGHTING.COMEcoSense Lighting Inc.915 Wilshire BoulevardSuite 2175Los Angeles, CA 90017
Specifications subject to change without notice. Visit EcoSenseLighting.com for the most current specifications.
2014 All rights reserved.EcoSense, the EcoSense logo, and EcoSpec are regis-tered trademark of EcoSense Lighting Inc. SPEC-LCIS-20140110-V1
Phone 310-496-6255Fax 310-496-6256Toll Free 855-632-6736 855-6-ECOSEN
5
DATE
PROJ.
FIRM
TYPE
EcoSpec® Linear INT - Standard Power
New Linear Series
PHOTOMETRY CHARACTERISTICS For complete library of IES files, please visit:ecosenselighting.com
CHARACTERISTICS:LINEAR INT - SP (LCIS) 4000K / 120°X 120°
Total Rated Fixture Lumens 306
Total Luminaire Efficiency 100%
Total Input Watts 4.38W
Horizontal Beam Angle (50%) 113.6
Vertical Beam Angle (50%) 110.5
Horizontal Field Angle (10%) 157.9
Vertical Field Angle (10%) 152
CHARACTERISTICS:LINEAR INT - SP (LCIS) 3500K / 120°X 120°
Total Rated Fixture Lumens 264
Total Luminaire Efficiency 100%
Total Input Watts 4.61W
Horizontal Beam Angle (50%) 113
Vertical Beam Angle (50%) 110.3
Horizontal Field Angle (10%) 157.5
Vertical Field Angle (10%) 150.1
CHARACTERISTICS:LINEAR INT - SP (LCIS) 3000K / 120°X 120°
Total Rated Fixture Lumens 249
Total Luminaire Efficiency 100%
Total Input Watts 4.58W
Horizontal Beam Angle (50%) 112.8
Vertical Beam Angle (50%) 109.9
Horizontal Field Angle (10%) 158
Vertical Field Angle (10%) 150.9
CHARACTERISTICS:LINEAR INT - SP (LCIS) 2700K / 120°X 120°
Total Rated Fixture Lumens 223
Total Luminaire Efficiency 100%
Total Input Watts 4.28W
Horizontal Beam Angle (50%) 112.3
Vertical Beam Angle (50%) 109.7
Horizontal Field Angle (10%) 157.4
Vertical Field Angle (10%) 151.4
0 22.5 45 67.5 900 81.5 81.5 81.5 81.5 81.55 81.2 81.5 81.7 81.6 81.815 78.6 79.1 79.8 80.0 80.425 73.4 74.5 75.6 75.8 76.135 65.4 66.8 68.6 69 69.445 54.9 57.5 58.7 59 59.655 42 44.6 46.1 46.2 46.465 26.9 29 30 28.9 28.875 11.7 12.3 11.1 13.2 13.985 1.4 1.6 1.1 1.1 1.390 0.3 0.4 0.7 1.0 1.1
0 22.5 45 67.5 900 90.7 90.6 90.7 90.6 90.75 90.4 90.1 89.9 89.5 89.615 87.7 86.8 86.2 85.2 85.225 82.4 81 79.7 78.3 7835 73.7 71.8 70.1 68.4 68.145 62.3 60.5 57.7 55.8 55.355 48.1 45.9 42.9 39.6 38.565 31.2 28 23.7 19.9 18.375 14.2 9.9 5.7 4.2 3.385 1.7 1 0.6 0.4 0.590 0.3 0.1 0.3 0.3 0.3
0 22.5 45 67.5 900 95.8 95.8 95.8 95.8 95.85 95.5 95.3 95 94.6 94.615 92.6 91.9 90.8 90.1 90.325 86.9 85.7 83.8 83 82.535 77.8 76 74.2 73 72.245 66.1 64.2 61.5 59.4 58.655 51.2 48.4 45.1 41.6 40.165 33.1 29.9 24.5 19.9 18.175 14.6 10.5 5.4 3.5 385 2 1.5 1 0.8 0.990 0.5 0.3 0.7 0.6 0.7
0 22.5 45 67.5 900 110 109.9 110 109.9 1105 109.7 109.4 109.2 108.8 108.915 106.7 105.8 105.4 104.2 104.325 100.2 98.9 98 96.4 96.135 90 88.4 86.8 84.8 84.545 76.2 74.9 71.9 69.6 68.955 58.6 57 53.2 49.1 4865 38.6 35.9 29.2 25 23.575 17.4 12.5 8.1 6.7 5.585 2.1 1.2 0.8 0.6 0.790 0.4 0.3 0.5 0.5 0.5
Photometrics by an independant lab in accordance with current IES published Procedures.* Lumen measurements comply with IES LM-79-08.IES data is available at www.ecosenselighting.com
RESERVE FOR FOOTCANDLE ESTIMATOR CHART
RESERVE FOR FOOTCANDLE ESTIMATOR CHART
0
10 000
20 000
30 000
40 000
50 000
180°
0°
cd
60°60°
30° 30°
90°90°
IES Direction
0
20 000
40 000
60 000
80 000
180°
0°
cd
60°60°
30° 30°
90°90°
IES Direction
180°
0°
cd
60°60°
30° 30°
90°90° 0
20 000
40 000
60 000
80 000
IES Direction
180°
0°
cd
60°60°
30° 30°
90°90° 0
20 000
40 000
60 000
80 000
100 000
IES Direction
120°x 120°
2700
K*
3000
K35
00K
4000
K
3.281ft1m
9.496ft289.45cm
18.99ft578.90cm
28.49ft868.35cm
37.99ft1157.80cm
47.48ft1447.25cm
DiameterAngle:110.71degEavg,EmaxHeight
6.562ft2m
9.843ft3m
13.12ft4m
16.4ft5m
3.220,10.23fc34.66,110.11x
0.8050,2.558fc8.665,27.53lx
0.3578,1.137fc3.851,12.24lx
0.2012,0.6394fc2.166,6.883lx
0.1288,0.4092fc1.386,4.405lx
3.281ft1m
9.53ft290.485cm
19.06ft580.96cm
28.59ft871.45cm
38.12ft1161.93cm
47.65ft1452.41cm
DiameterAngle:110.90degEavg,EmaxHeight
6.562ft2m
9.843ft3m
13.12ft4m
16.4ft5m
2.787,8.909fc29.99,95.89lx
0.6966,2.227fc7.499,23.97lx
0.3096,0.9899fc3.333,10.65lx
0.1742,0.5568fc1.875,5.993lx
0.1115,0.3564fc1.200,3.836lx
3.281ft1m
9.428ft287.36cm
18.86ft574.71cm
28.28ft862.07cm
37.71ft1149.42cm
47.14ft1436.78cm
DiameterAngle:110.32degEavg,EmaxHeight
6.562ft2m
9.843ft3m
13.12ft4m
16.4ft5m
2.635,8.434fc28.36,90.79lx
0.6588,2.109fc7.091,22.70lx
0.2928,0.9371fc3.152,10.09lx
0.1647,0.5271fc1.773,5.674lx
0.1054,0.3374fc1.135,3.631lx
3.281ft1m
9.384ft286.02cm
18.77ft572.04cm
28.15ft858.06cm
37.54ft1144.08cm
46.92ft1430.10cm
DiameterAngle:110.07degEavg,EmaxHeight
6.562ft2m
9.843ft3m
13.12ft4m
16.4ft5m
2.362,7.582fc25.43,81.61lx
0.5905,1.896fc6.357,20.40lx
0.2625,0.8425fc2.825,9.068lx
0.1476,0.4739fc1.589,5.101lx
0.0945,0.3033fc1.017,3.265lx
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
52 of 65
hanjip restaurant| DtLa 12 may 2016
sD3
ECOSENSELIGHTING.COMEcoSense Lighting Inc.915 Wilshire BoulevardSuite 2175Los Angeles, CA 90017
Specifications subject to change without notice. Visit EcoSenseLighting.com for the most current specifications.
2014 All rights reserved. EcoSense, the EcoSense logo, and EcoSpec are regis-tered trademark of EcoSense Lighting Inc. SPEC-LCIS-20140110-V1
Phone 310-496-6255Fax 310-496-6256Toll Free 855-632-6736 855-6-ECOSEN
6
DATE
PROJ.
FIRM
TYPE
EcoSpec® Linear INT - Standard Power
New Linear Series
LIGHTING FACTS LABELS
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
53 of 65
hanjip restaurant| DtLa 12 may 2016
sD4
TOKILUX WA
LL GRA
ZER SUBM
ITTAL
CATALOG
#: TLXWG
-(2400
,2700
,300
0)-XX
DATE: M
ARCH 30
, 2015
DRAW
N BY: R. CORDOVA
SCA
LE: 1:2
WEIG
HT: 55g/ft.
TOK
ISTAR
LIGH
TING
INC
.1
01
5 E. D
ISCOVER
Y LA
NE
AN
AH
EIM, C
A 9
2801
TEL: 714 7
72
7005
FAX: 7
14
772 7
014
email: info@
tokistar.com W
ebsite: tokistar.com
NO.123456
PART
LIGH
T BAR
LED
RAIL
FEED END
END CAP
RETAIN
ER CLIP
MATERIA
L
RIGID POLYCA
RBONATE
SOLID
-STATE LED
RIGID POLYCA
RBONATE
R IGID POLYCA
RBONATE
RIGID POLYCA
RBONATE
META
L
TLXW
G S
eries / Wall G
razer
P
TOTA
L LENGTH
= P x (No. of LIGH
T BARS
)
0.64"
0.54"
35
21
P (LIGH
T BAR)
8 IN.
CATALO
G #
TLXWG
-(2400
,2700
,300
0)-XX
XX = NO. OF LIGH
T BARS
MA
X. LENGTH
15.76 FT. (24 LIG
HT BA
RS)
46
0.6
4"
0.54"
BEA
M S
PREAD: 18
˚ X 48˚
TOKILUX WA
LL GRA
ZER SPECIFICATIONS
INPUT VOLTAG
E: 24 VDC OR 24 VAC
CURRENT: 167m
A PER LIG
HT BA
RPOW
ER: 4.0 W
PER LIGH
T BAR
LED CODE240
0270
030
00
COLOR240
0K
2700
K30
00
K
47.5 Lm PER WATT
47.5 Lm PER WATT
50 Lm PER W
ATT
285 Lm PER FT.
285 Lm PER FT.
300
Lm PER FT.
OUTPUT
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
54 of 65
hanjip restaurant| DtLa 12 may 2016
sD5
Fixture Type:
Catalog Number:
Project:
Location:
WAC Lightingwww.waclighting.comPhone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive • Port Washington, NY 11050Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Avenue • Ontario, CA 91760Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY 2015
InvisiLED® Pro 2 24V High Output LED Tape Light
PRODUCT DESCRIPTION
Professional grade white tape light that delivers optimal color consistency and brightness. An ideal system for task or accent lighting applications.
FEATURES
• California Title 24 Compliant (2700K, 3000K & 3500K)• Ultra thin pro� le at 8"• Diodes spaced evenly at 1" on center• Minimum run length of 1' and maximum of 25'• May be fi eld cut every 6" at the end of a run• 80,000 hour rated life• 5 year WAC Lighting product warranty
SPECIFICATIONS
Construction: Flexible, silicone cased tape light. Peel and stick 3M construction adhesive on back. Indicating marks on back for fi eld cutting.
Power Supply: Remote and plug-in electronic Class 2 transformers. 120VAC 50/60Hz input, 24V 60W and 96W output.
Light Source: 12 LEDs per foot. Runs on 24V at 4W per foot.
Dimming: May be dimmed with electronic low voltage (ELV) dimmer.
Operating Temperature: -4°F − 122°F (-20°C − 50°C), relative humidity 95%.
Standards: UL & CUL Listed for damp locations.
FIXTURE PERFORMANCE – TAPE SECTIONS
Color Temp Watts/ft Lumens/ft Effi cacy (Lm/W) CRI2700K 4 325 81 903000K 4 300 75 903500K 4 330 83 904500K 4 330 83 85
FIXTURE PERFORMANCE – 5 LED "L" CONNECTOR
Color Temp Watts Lumens Effi cacy (Lm/W) CRI2700K 2 130 65 903000K 2 130 65 903500K 2 135 66 904500K 2 135 66 85
LED-TX24 – – WT
Example: LED-TX2445-6IN-WT
LED-TX24 – 5L – WT
Example: LED-TX2435-5L-WT
ORDER NUMBER – TAPE SECTIONS
Model # Color Temp Length Qty Tape Color
LED-TX24
27303545
2700K3000K3500K4500K
6IN151-40
6 inches1 foot5 feet1 foot
11140
WT White
ORDER NUMBER – 5 LED "L" CONNECTOR
Model # Color Temp Tape Color
LED-TX24
27303545
2700K3000K3500K4500K
5L-WT White
Tape Section 5 LED "L" Connector
22"
22"
a"a"
8" 6", 1', 5'
1"
POWER SUPPLIES
Remote (Hard-Wired)EN-2460-RB2-TEN-24100-RB2-TEN-24100-277-R
120VAC, 60W Class 2 LED transformer120VAC, 96W Class 2 LED transformer277VDC, 100W Class 2 LED transformer
Plug-inEN-2460-P-AR-TEN-24100-P-AR-T
120VAC, 60W Class 2 LED transformer120VAC, 96W Class 2 LED transformer
POWER SUPPLY ACCESSORIESTB-SLED-TC-B2LED-T-BLED-TC-P-2LED-TC-P-12LED-TC-EXT-144
Wiring box with switchWiring terminal with 2" female feed.Low voltage wiring box2' lead wire for power supply12' lead wire for power supply12' extension cable
TAPE LIGHT ACCESSORIESLED-TC-ICLED-TC-XLED-TC-YLED-TC-L
Joiner cables"X" connector"Y" connector"L" connector
LED-TC-ECLED-T-CLLED-T-RCLED-T-CH
End cap Mounting clipsRetro� t channelRigid aluminum channel
See next page for full specs and descriptions.
22"
22"
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
55 of 65
hanjip restaurant| DtLa 12 may 2016
sD5
InvisiLED® Pro 2 – Power Supplies And AccessoriesPOWER SUPPLIES Model # Input Output Dimensions Description
120V ACRemote Class 2 Transformer
EN-2460-RB2-T EN-24100-RB2-T
120V120V
24V/60W24V/96W
62" × 1s" × 14"6s" × 1s" × 18"
6’ lead wire included. Requires a minimum load of 1W.Max run 60W: 15'Max run 96W: 25'
120V ACPlug-in Class 2 AC Transformer
EN-2460-P-AR-T EN-24100-P-AR-T
120V120V
24V/60W24V/96W
2w" × 1s" × 1w"42" × 1d" × 1w"
6’ lead wire included. Requires a minimum load of 1W.Max run 60W: 15'Max run 96W: 25'
277V DC Remote Class 2 Transformer
EN-24100-277-R 277V 24V/100W 7d” × 2w” × 1a” Cannot be dimmed. Converts 277V to 24V.Includes 1' input and output wires.Must use LED-TC-EXT-144 to extend the distance between power supply and tape section.
POWER SUPPLY ACCESSORIES Model # Dimensions Description
Wiring box with switch
TB-S 64” × 1s” × 14” Use when spanning a large gap in a system layout without leaving exposed wiring (ie: lighting kitchen cabinets on both sides of a sink or window). Low voltage wiring is collected inside box, with Romex® wire output to go behind a wall.
Low Voltage Wiring Box With Feed
LED-TC-B2 12” × w” × s” Wiring terminal for 24V InvisiLED with2" female feed.
Low Voltage Wiring Box
LED-T-B 12” × w” × d” Neatly house up to 2 wires.
Lead Wire LED-TC-P-2 LED-TC-P-12
2'12'
Alternative length of lead wires for plug-in or remote power supply. May be � eld cut for use with a remote power supply.
Extension Cable LED-TC-EXT-144 12' Use to extend the distance between power supply and tape section.
TAPE LIGHT ACCESSORIES Model # Dimensions Description
Joiner Cable LED-TC-IC2 LED-TC-IC6 LED-TC-IC12LED-TC-IC36 LED-TC-IC72
2"6"12"36"72"
Connects two sections of InvisiLED® Pro.
4-Way "X" Connector
LED-TC-X 3w” × 3w” × c”center: w” arms: 12” each
"X" connector has one male and three female connectors. (Total run length power consumption cannot exceed transformer load when "X" connector is used).
3-Way "Y" Connector
LED-TC-Y 3z” × 3z” × c”center: w” arms: 12” each
"Y" connector has one male and two female connectors.(Total run length power consumption cannot exceed transformer load when "Y" connector is used).
"L" Connector LED-TC-L 1a" × 1c" × 4" "L" connector has male and female connectors, use to create 90° right angles.
End cap
LED-TC-EC 2" × 4" × x"2" × 2" × 8"
Includes 1 cut end cap and 1 male end cap. Use to terminate every run to protect against contaminants.
Mounting Clips (10 pack)
LED-T-CL 2" For installation on surfaces that are di� cult to adhere to. Two mounting clips per foot are recommended for straight runs.
Retro� t Channel LED-T-RC 36" × 2" × 2" Use to construct a miniature cove or light ba� e in which tape may be concealed. May also be mounted to the channel as a way to change the direction of the projected light.
Rigid Aluminum Channel
LED-T-CH 5' × n” × a” Mounting channel with acrylic di� user.
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
56 of 65
hanjip restaurant| DtLa 12 may 2016
sD6
TOKILUM SERIES SUBMITTAL
CATALOG#: LUM-(50, 100, BL)-_
DATE: SEPTEMBER 7, 2012
DRAWN BY: R. CORDOVA
SCALE: 1:1.33
WEIGHT: 43 g/ft.
TOKISTAR LIGHTING INC.1015 E. DISCOVERY LANE
ANAHEIM, CA 92801TEL: 714 772 7005 FAX: 714 772 7014
email: [email protected] Website: tokistar.com
NO.
1
2
3
4
5
PART
CABLE
LED
END CAP
SHRINK TUBE
LEAD WIRE
TOKILUM Series
MATERIAL
PVC INSULATION WITH PLATED #18 AWG X 4
SOLID STATE LED
PVC
POLYOLEFIN PVC INSULATION WITH PLATED #18 AWG X 4
CORD COLORCIRCUIT 1: WHITE 6VDC+CIRCUIT 1: BLACK/WHITE 6VDC -CIRCUIT 2: BLACK/RED 6VDC -CIRCUIT 2: RED 6VDC +
MAX LENGTH20 FT.20 FT.20 FT.40 FT.40 FT.40 FT.
P (INCH)2 + .082 + .082 + .084 + .164 + .164 + .16
CATALOG #LUM-50-IWLUM-50-WHLUM-50-BLLUM-100-IWLUM-100-WHLUM-100-BL
.32"
.20
"
.14" 1.14".59"ø
P
.70
8"
TOTAL LENGTH = P x (No. of Modules -1)
3 1 4 52
KELVIN3000K6500KBLUE
3000K6500KBLUE
TOKILUM LED SPECIFICATIONSVOLTAGE: 6VDCCURRENT: 80mAPOWER: 0.48W
COLOR3000K6500KBLUE
OUTPUT16Lm9.8Lm4.8Lm
LED CODEIWWHBL
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
57 of 65
hanjip restaurant| DtLa 12 may 2016
tD1
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
58 of 65
hanjip restaurant| DtLa 12 may 2016
tD1
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
59 of 65
hanjip restaurant| DtLa 12 may 2016
tD2
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
60 of 65
hanjip restaurant| DtLa 12 may 2016
tD2
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
61 of 65
hanjip restaurant| DtLa 12 may 2016
tD2
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
62 of 65
hanjip restaurant| DtLa 12 may 2016
REV-10/12
CURRENT LIMITING LIGHTING CONTROL PANEL
Supplemental Overcurrent ProtectionCity of Los Angeles Approved Version
D1.15.0.LA
Project:
Fixture Type:
Location:
Contact/Phone:
PRODUCT DESCRIPTIONThe Juno Trac-Master® Current Limiting Lighting Control Panel is THE solution for complying with stringent energy codes like ASHRAE 90.1 and California Title 24. Typically for track lighting, it is defined as a sub-branch circuit current limiter designed to limit available watt-age to lighting circuits, to only that necessary to meet the lighting design criteria. The Trac-Master panel employs supplementary current limiting protectors configured specifically for the lighting design in the space. Rather than lighting loads being calculated by the greater of maximum fixture wattage ratings or an arbitrary watts per foot multiplier, the Trac-Master panel enables calculations to instead be made based on the rating of the supplementary protector. Because it limits a circuit not the lighting equipment itself, the Trac-Master Lighting Control Panel provides maximum flexibility to accommodate frequent lighting design modifications and layout changes, especially typical for retail spaces.
ORDERING INFORMATIONSupplementary Protector ratings are determined by the electrical layout drawings. A submittal package will be provided by Juno for approval following receipt of order and single line drawings. Supplementary Protector ratings and position are not required to be specified as part of the catalog number. Specifications assistance is available thru local Juno Lighting Group sales representatives or by contacting Juno Lighting Group Technical Services at (888) 387-2212.
PRODUCT SPECIFICATIONSFeatures Designed to be installed between the branch circuit breaker and the lighting equipment • Not intended to be used as a branch circuit protective device • Factory pre-assembled and customized • No programming required.
Construction Heavy-duty 16 gauge die formed steel enclosure • Hinged door with key-locking latch • Removable front panel with factory labeled breaker wiring data simplifies installation • Ample quantity of combination ( 1/2”, 3/4”, 1” ) knockouts provide maxi-mum installation flexibility for top, bottom and side conduit connections • Precision 35mm DIN rail mounting secures breakers in place • Includes ample ground terminals for all circuits • Mini panel accommodates 1 to 12 circuits, standard panel accommodates 6 to 21 circuits and large panel accommodates 22 to 42 circuits • Mini panel available in surface mount configuration only • Standard and large available in surface mount or flush mount configurations.
Finish Durable powder coat paint • Industrial gray color standard.
Supplementary Protectors Single pole supplementary protectors • Rated for 120/277VAC operation • Available in individual amperage ratings including 0.5A, 1A, 2A, 3A, 4A, 5A, 6A, 7A, 8A, 10A, 13A and 15A, selected based on actual lighting loads • Protectors should be loaded to a maximum of 80% of rating to avoid nuisance tripping • Wiring installs directly into protector terminal • Color-coded ON/OFF indicator clearly identifies status • Easily resettable in an accessible location in the event of an overcurrent situation • UL 1077, CSA 22.2, IEC 60947-2 approved.
Labels UL Listed • cUL Listed • City of Los Angeles Approved • Approved by the California Energy Commission to meet the require-ments of Title 24 • Complies with ASHRAE 90.1.
Warranty Product is warranted against defects in material and workmanship for a period of 3 years.
Product specifications subject to change without notice.
CLS
Series Number of Circuits per Panel Panel Style Mounting Style
CLS = Trac-Master Current 6-21 for Standard Panel Blank = Standard Panel (6-21 circuits) Blank = Surface Mount Limiting Lighting 22-42 for Large Panel or Large Panel (22-42 circuits) F = Flush Mount (Standard or Large Panel Only) Control Panel 1-12 for Mini Panel M = Mini Panel (1-12 circuits)
Ordering Examples: CLS10M, CLS16, CLS21F
tD2
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
63 of 65
hanjip restaurant| DtLa 12 may 2016
DIMENSIONS
9 1/16"
12 3/4"
3 15/16"
MINI 1-12 CIRCUIT PANEL - SURFACE MOUNT
D1.15.0.LA
1300 S. Wolf Road • Des Plaines, IL 60018 • Phone (847) 827-9880 • Fax (847) 827-2925220 Chrysler Drive • Brampton, Ontario • Canada L6S 6B6 • Phone (905) 792-7335 • Fax (905) 792-0064Visit us at junolightinggroup.com Printed in U.S.A. ©2012 Juno Lighting, LLC.
CURRENT LIMITING LIGHTING CONTROL PANEL
tD2
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
64 of 65
hanjip restaurant| DtLa 12 may 2016
D1.15.0.LA
APPLICATIONEnergy codes typically calculate track lighting loads based on linear feet of installed track. Some codes use a multiplier as low as 30 watts/foot while others use a multiplier as high as 70 watts/foot. When using the energy efficient lighting technologies avail-able today, the connected load is typically much less than the per-foot multipliers used by most energy codes. This penalizes lighting designs that employ track lighting and wastes available lighting watts that could be used more effectively.
Below is a typical track lighting example. The Standard Layout consists of 100’ runs of single circuit track with 32 CMH track heads, each using 39W lamps, for a total connected load of 1440W. The Revised Layout Using Short Track Segments has the same 1440W connected load but uses sixteen short 4’ track segments (64’), each fed separately, to help minimize the impact of the watts per foot multiplier. The scenario with the Trac-Master Current Limiting Control Panel uses the original 100’ of single circuit track, with each monitored by a 4-Amp current limiting supplementary protector that is closely matched to the actual connected load of 1440W plus a small buffer. This results in the minimum calculated watts per the energy codes.
1. Standard Layout without the Trac-Master Control Panel
2. Revised Layout Using Short Track Segments
The Trac-Master Panel installs between the branch circuit breaker and the track lighting, solving the energy code calculation discrepancy, making the wattage calculation independent of track length.
3. Standard Layout with the Trac-Master Control Panel
1300 S. Wolf Road • Des Plaines, IL 60018 • Phone (847) 827-9880 • Fax (847) 827-2925220 Chrysler Drive • Brampton, Ontario • Canada L6S 6B6 • Phone (905) 792-7335 • Fax (905) 792-0064Visit us at junolightinggroup.com Printed in U.S.A. ©2012 Juno Lighting, LLC.
CURRENT LIMITING LIGHTING CONTROL PANEL
tD2
LiGhtinG DesiGn aLLianCe, inC.
LOs anGeLes2830 tempLe aVenueLOnG BeaCh, Ca 90806-2213
t: 562.989.3843F: 562.989.3847www.LightingDesignAlliance.com
Lighting CAtALog PAgE
tYPE
65 of 65
hanjip restaurant| DtLa 12 may 2016
L I G H T P A N E L S Y S T E M S
L I G H T P A N E L S Y S T E M S
13101 W. Washington Blvd. #469Los Angeles, CA 90066
p 310.616.5070f 310.616.5056
Light Panel SystemProduct OverviewThe eos Light Panel System is an ultra-slim sheet of light that combines LED lighting technology and an exclusive 3D cutting process to give you a versitile light source that generates a soft & even beam of light virtually without any heat. It’s slim profile and low power draw make the eos Light Panel System usable in large number of applications including indoor, outdoor, display lighting, accent and signage lighting.
Super Slim:• The whole thickness of the LED Light Panel System is only 3/8”.Outdoor Applications - IP 67 Approved:• Moisture Proof and Water-Resistant Light Panel System can be
used for select outdoor lighting.Long Lifetime & Virtually Maintenance Free• Over 50,000 hours = Nearly 12 years at 12 hours a day. The eos Light
Panel System, once installed, is virtually maintenance free and labor-free.
Low Power Consumption & Cost Savings:• The eos Light Panel System consumes up to 70% less power than a
T5 flourescent lamp. The initial cost may be higher, but energy savings are higher and overall durability is exceedingly better.
Eco-Friendly Product:• This is the Optimum Lighting Technology of the 21st Century as it
contains NO mercury nor any other heavy materials.Hospital & MRI Safe:• The system contains no ferrous/magnetic materials, making it safe for
MRI suites with a remote power supply up to 30 feet from the applicationHigh Quality & Approved Parts:• Patented LED, cystal acrylic, stainless plate, & bolt. Durable silcone
rubber under high temperature. UL, ETL, CE approved adapter and electrical wiring.
Indoor Accent Lighting Advertising Signage Architectural Design
5300k -4200k -3000k -2700k -RGB -
Clean WhiteNeutral WhiteWarm WhiteTungsten WhiteColor Changing
Color Tempatures: Color Temp.:10000 - 15000 K
6500 - 8000 K5000 - 6500 K4000 - 5000 K3000 - 4000 K2500 - 3000 K
Light Source:Clear Blue SkyCloudy Sky / ShadeDaylightFlourescent LightEarly AM / Late PMDomestic Lighting
Product SpecificationMaximum Size: (A) 157” x 63” -or- (B) 118” x 78”. Panels can be cut in nearly any unique 2D shape, as well as 3D applications. Voltage: 12VDC Wattage: 6W/Linear Foot (Single Side LED)
ZD1