PAGE 3 HEADLIGHT OIL RADIATOR SCREEN/GRILL & ANTI GLARE SHIELD

PAGE 5 HEADLIGHT SCREEN & ANTI GLARE SHI

PAGE 7 QUICK HEADLIGHT SCREEN R1150GS&A

PAGE 9 QUICK RELEASE FASTNERS

HE

AD

LIG

HT

OIL

RA

DIA

TO

R S

CR

EE

N/

GR

ILL

& A

NT

I GL

AR

E S

HIE

LD

1

3

7

5

Tool Required: T27 On Left & Right Indicator, Then PullIndicator Out Of Its Frame Location Hole

Torx Bit. Undo Bolt

The Stainless Steel Bracket Should BePositioned Under The Indicator Lug &The Torx Bolt Holes Should Be In Line

Visual Of: Both Stainless SteelBrackets Mounted Correctly

Tools Required: 2.5mm Allen Key &7mm Ring Spanner

2

6

4

8

Take Note At This Point Of Bolt & LugHole Positions When Marrying TheStainless Steel Bracket To The Indicator

Mount M4 Bolts From The Front, PassingThem Through The Screen and StainlessSteel Bracket, Then Screw Nut On To Rear.Do Not Tighten Fully Until All FixingsAre In Place

Mount Indicator With Stainless SteelBracket, So Indicator Lug Locates In ToIts Frame Hole. Screw Torx Bolt UpUntil Tight. Repeat On Other Side

When Mounting Screen/Grill, AngleThe Part So Grill Passes Under FrameBar & Then Rotate So Screen HolesMarry Up To Stainless Steel Bracket Holes

HE

AD

LIG

HT

& A

NT

I GL

AR

E S

HIE

LD

1

3

7

5

Tool Required: T27 On Left & Right Indicator, Then PullIndicator Out Of Its Frame Location Hole

Torx Bit. Undo Bolt

The Stainless Steel Bracket Should BePositioned Under The Indicator Lug &The Torx Bolt Holes Should Be In Line

Visual Of: Both Stainless SteelBrackets Mounted Correctly

Tools Required: 2.5mm Allen Key &7mm Ring Spanner

2

6

4

8

Take Note At This Point Of Bolt & LugHole Positions When Marrying TheStainless Steel Bracket To The Indicator

Mount M4 Bolts From The Front, PassingThem Through The Screen & StainlessSteel Bracket, Then Screw Nut On To Rear.Do Not Tighten Fully Until All FixingsAre In Place

Mount Indicator With Stainless SteelBracket, So Indicator Lug Locates In ToIts Frame Hole. Screw Torx Bolt UpUntil Tight. Repeat On Other Side

When Mounting Headlamp ProtectorAlign So Screen Holes Marry Up ToStainless Steel Bracket Holes

HE

AD

LIG

HT

SH

IEL

D R

115

0G

S&

A

7

6

8

1Kit Contents: Tool Required: T25 Torx Bit.1 x Main Screen, 2 x Brackets

2 x M5 Stainless Steel Bolts4 x Quick Release FastenersWhen Received Kit May BePart Assembled

Undo Screws & Remove Them2 x Stainless Steel Pillar Nuts From Left & Right Handside Of

Headlight Surround, ReplaceWith Stainless Steel Pillar NutsDoing Up Until Finger Tight

2

Tool Required: 8mm Socket & Drive.Do Stainless Steel Pillar Nuts UpUntil Tight

3Tool Required: 3mm Allen Key.Marry Screen Screws Up To EndsOf Stainless Steel Pillar NutsLocate Allen Key Through HoleOnto Head Of Screw & Do UpUntil Tight

4

Pulling Back On The FastenerKnob Will Release ScreenIn Seconds For Ease OfMaintenance

5Visual Of: Both Stainless Steel

Make Sure There’s No Gap

Pillar Nuts & Brackets With

Between The Screen &

Screen Removed. To Reattach

Brackets & Fasteners Are In

Against Screen. Once The

Screen Marry Screen Upto

There Unlocked Position

Fastener Is In Position Push

Brackets & Align Holes Up

Unlocked Position

Fastener Knob

Fastener Pin& Bayonet

Locked Position

Waist Washer

Unlocked Position

Fastener Knob

Waist Washer

Locate Fasteners Into Screen &

The Knob In Until The

Bracket Hole So Waist Washer Is

The Fastener Locks In Place

QU

ICK

RE

LE

AS

E F

AS

TE

NE

RS

1

3

7

5

Tools Required: 2.5mm Allen Key& 7mm Ring Spanner

Fastener Knob

Fastener Pin& Bayonet

Waist Washer

Make Sure The Screen &Bracket Holes Are Aligned

x

xLocate Fastener Into Screen & Bracket HoleSo Waist Washer Is Against Screen

Remove All 4 Nuts & Screws

2

6

4

8When All 4 Fasteners Are In PositionScreen Will Be Secure. To Release ScreenPull Fastener Knob Out Until It Releases.To Re-Secure Repeat Sections 4 Thru To 7

& There Is No Gap Between The Two

Once The Fastener Is In Position Push TheKnob In Until The Fastener Locks In Place