ex 6200 - datasheet.pdf
TRANSCRIPT
-
DATASHEET
1
Product DescriptionJuniper Networks EX6210 Ethernet Switch offers a total of 10 slots which allow for highly
flexible configurations. Two of the slots are designed to hold Switch Fabric and Routing
Engine (SRE) modules, while the remaining eight slots are dedicated I/O slots for holding
any combination of EX6200 line cards. Since only one SRE module is required for switch
operations, one of the SRE slots can be optionally configured as an I/O slot*, enabling the
switch to support a total of nine EX6200 line cards.
Each SRE module includes four 10GbE uplinks, while the line cards feature full PoE+
support to deliver complete investment protection.
Architecture and Key ComponentsAt 14 rack units (U) high and just 15.5 inches deep, the EX6210 is compact enough to easily
fit in traditional wiring closets, making it ideal for campus deployments.
The chassis is cooled front to back by a single fan tray with redundant fans (three groups
of two each). The EX6210 can operate with a single fan failure, and in the unlikely event of
an entire fan tray failure, the system will operate for two minutes with no cooling while the
fan tray is replaced.
The EX6210 switch has four power supply slots and supports 2,500 W AC, 5,000 W AC*,
or 2,100 W DC power supplies (different power supplies should not be mixed in the same
chassis). The EX6210 ships with a single power supply; up to three more load-sharing
power supplies can be added and configured for N+1 or N+N (2+2) redundancy, providing
up to 10,000 W AC (with 2,500 W AC PSUs), 20,000 W (with 5,000 W AC PSUs), or
8,400 W DC (with 2,100 W DC PSUs) to the chassis.
Product Overview
The Juniper Networks EX6200 line
of Ethernet switches is a scalable,
resilient, high-performance chassis-
based wiring closet solution, providing
extremely high port densities in a
space-optimized form factor. With
a choice of data only or Power over
Ethernet (PoE) and PoE+ port options,
the EX6200 delivers high availability
and tremendous investment protection
for enterprise campus environments,
as well as data center access
deployments using end-of-row designs.
EX6200 LINE OF ETHERNET SWITCHES
*Roadmap
-
2Switch Fabric and Routing Engine Module
The SRE module, which provides 720 Gbps (full duplex) of
switching capacity to the EX6200 chassis, includes an integrated
switch fabric and is responsible for system configuration and
management, running bridging and routing protocols, and
managing the user interface.
A front panel, chassis-level LCD panel displays Routing Engine
status as well as chassis component alarm information for
rapid problem identification and resolution to simplify overall
operations. The LCD also provides a flexible, user-friendly interface
for performing device initialization and configuration rollbacks,
reporting system status and alarm notification, or restoring the
switch to its default settings.
EX6200 Line Cards
Line cards are responsible for implementing packet forwarding,
filtering, and queuing functions. The EX6200 line supports the
following line cards:
EX6200-48T: A 48-port 10/100/1000BASE-T RJ-45 line
card offering 3 to 6 s port-to-port latency for all packet sizes
(except jumbo frame), eight quality-of-service (QoS) queues
per port, and a 6 MB buffer for all 48 ports.
EX6200-48P: Identical to the EX6200-48T, the EX6200-
48P also includes support for the IEEE 802.3at PoE+ standard
on all 48 ports, delivering up to 30 watts of power per port
for supporting networked devices such as telephones, video
cameras, multiple radio IEEE 802.11n wireless LAN (WLAN)
access points, and video phones in converged network
environments. The EX6200-48P also supports the 802.3af PoE
standard, which delivers up to 15.4 watts of Class 3 PoE per
port.
Configuration Options and Port Densities
The EX6210 switch supports two primary configurations: high
availability (HA) and high density.
HA configuration: In a redundant configuration with two
SRE modules and up to eight EX6200 line cards installed,
the EX6210 can support a maximum of 384 wire-speed
10/100/1000BASE-T ports.
High-density configuration: In a high-density configuration,
one of the SRE modules is replaced with an additional line
module, bringing the total number of 10/100/1000BASE-T
input/output ports to a maximum of 432. Note that this
configuration introduces minor oversubscription on the ports in
the system.
Deployment ScenariosThe EX6210 is a highly scalable campus wiring closet solution,
supporting up to 432 GbE access ports per chassis. The switch
is designed for mobility and enterprise-class services with high
density of PoE+, making it ideal for converged data, voice, and
video deployment environments.
Figure 1: EX6200 campus access deployment
The EX6210 is also an ideal solution for GbE data center server
access end-of-row or middle-of-row deployments. The switchs
modular chassis form factor enables IT to consolidate locations
for networking equipment, while the front-to-back airflow
optimizes data center deployments.
Figure 2: EX6200 data center 1GbE access deployment
Junos Operating SystemThe EX6200 line runs the same Juniper Networks Junos operating
system used by other Juniper Networks switches, routers,
and security devices. By utilizing a common operating system
across multiple product families, Juniper delivers a consistent
implementation and operation of control plane features across
all products.
Campus Wiring Closet
Building 1
Aggregation
Access
EX6200EX6200
Closet A1 Closet B1
IDF 1
End-of-row 1GbE Data Center Server Access
EX6200
1GbE Server
-
3SecurityThe EX6200 line of Ethernet switches fully integrates with Juniper
Networks Unified Access Control as well as third-party UAC
solutions. UAC consolidates all aspects of a users identity, device,
and location, enabling administrators to enforce access control
and security down to the individual port or user level.
Working as an enforcement point within the UAC, the EX6200
provides both standards-based 802.1X port-level access
control as well as Layer 24 policy enforcement based on user
identity, location, and/or device. A users identity, device type,
machine posture check, and location can be used to determine
whether access should be granted and for how long. If access is
granted, the switch assigns the user to a specific VLAN based on
authorization levels. The switch can also apply QoS policies or
mirror user traffic to a central location for logging, monitoring, or
threat detection by intrusion prevention systems.
The EX6200 also provides a full range of Layer 2 and Layer 3 port
security features, including Dynamic Host Configuration Protocol
(DHCP) snooping, dynamic ARP inspection (DAI), and media access
control (MAC) limiting to defend against internal and external
spoofing, man in the middle, and denial-of-service (DoS) attacks.
Management Capabilities The following system management options are available for the
EX6200 line of Ethernet switches.
The standard Junos OS command-line interface (CLI) offers
the same granular management capabilities and scripting
parameters found in any router or switch powered by Junos OS.
The integrated Junos Web management tool provides an
embedded device manager that allows users to configure,
monitor, troubleshoot, and perform system maintenance on
individual switches via a browser-based graphical interface.
Juniper Networks Junos Space, an open, programmable
application platform for hosting a comprehensive suite of
network operational application tools provides an open
approach for automating the deployment and operation of a
Juniper infrastructure. Explicitly designed to allow partners and
customers to build and deploy smart, simple, and easy-to-use
applications, Junos Space provides multiple management and
infrastructure applications for managing Juniper resources
and assets, including inventory management, device and
interface configuration, automated software management
and deployment, and event-driven fault management. These
Junos Space applications offer predefined automation schemes
and best practice templates to enable rapid and accurate
configurations.
Enhanced Limited Lifetime Warranty The EX6200 includes an enhanced limited lifetime hardware
warranty that provides next business day advanced hardware
replacement for as long as the original purchaser owns the
product. The warranty includes lifetime software updates,
advanced shipping of replacement hardware within one business
day, and 24x7 Juniper Networks Technical Assistance Center
(JTAC) support for 90 days after the purchase date. Power
supplies and fan trays are covered for a period of five years. For
complete details, please visit www.juniper.net/support/warranty.
Features and BenefitsThe EX6200 line of Ethernet switches includes the following key
features and benefits:
High PoE+ density: The EX6200 can support the high PoE+
densities required for modern enterprise deployments with large
numbers of wireless access points, security cameras, smart
devices, and telephones. The EX6210 can support up to 384
PoE+ ports with N+1 redundancy in a redundant configuration
with two SRE modules and four 5,000 W AC power supplies*
installed. The EX6210 can also support up to 432 PoE+ ports
with N+1 redundancy in nonredundant configurations with one
SRE module and four 5,000 W AC power supplies* installed.
Resiliency: The EX6200 line is designed with robust HA
features, including redundant power supplies to ensure
hardware availability. Control plane and data plane separation,
combined with the Junos OS high availability design, ensures
maximum systems-level availability.
Layer 3 feature in base image: The EX6200 includes a rich set
of Layer 3 features, including OSPF support as part of the Junos
OS base software image.
*Roadmap
-
4Table 1: EX6210 Hardware Features
COMPONENT FEATURES
EX6210 chassis 2 SRE module slots and 8 I/O slots
Supports up to 384 10/100/1000BASE-T RJ-45 ports with 2 SRE modules installed, or 432 10/100/1000BASE-T RJ-45 ports* with 1 SRE module installed
Supports both PoE and PoE+
Front-to-back airflow
SRE module Support for four 10GbE small form-factor pluggable transceiver (SFP+) uplink ports
Line rate on all ports with two SRE modules installed
3:2 oversubscription for ports in 8 I/O slots; wire speed for ports in second SRE slot with one SRE installed
Integrated LCD
- Console port
- SFP and copper management ports for management access
- LCD and LEDs for reporting system status
- Front panel USB port for easily uploading new software and user configuration
- 2 GB internal USB/flash memory
Line cards 48-port 10/100/1000BASE-T RJ-45 line card
48-port 10/100/1000BASE-T PoE+ RJ-45 line card which includes support for IEEE 802.3af PoE and 802.at PoE+ standards on all ports
Power supplies Support for 2,500 W AC, 5,000 W AC*, or 2,100 W DC power supplies
Up to four power supplies per chassis
Load-sharing and hot-swappable
N+1 or N+N redundancy configuration options
More than 90% power efficiency
Cooling Front-to-back airflow
Fan tray in rear of chassis
Fan redundancytotal of 6 fans (2x3), cooling maintained if individual fan failure
Graceful system shutdown in thermal overload situations
Network Equipment Building System (NEBS) environmental standard*
EX6210
EX6200 Modular Switch Specifications
Dimensions (W x H x D) EX6210 chassis: 17.3 x 24.3 x 15.5 in (43.9 x 61.6 x 39.3 cm)
Weight 215 lb (98 kg) for fully loaded chassis (with one EX6210 chassis, one fan tray, eight I/O line cards, two SRE modules, and four power supplies)
159 lb (72 kg) for base system (with one EX6210 chassis, one fan tray, two I/O line cards, one SRE module, and one power supply)
EX6210 System Capacity Maximum backplane capacity: 4.4 Tbps Maximum system throughput: 690 Mpps
Environmental Ranges Operating temperature: 32 to 113 F (0 to 45 C) Storage temperature: -40 to 158 F (-40 to 70 C) Operating altitude: Up to 13,000 ft (3,964 m) Non-operating altitude: Up to 16,000 ft (4,877 m) Relative humidity operating: 5% to 90% (non-condensing) Relative humidity non-operating: 5% to 95% (non-condensing) Acoustic noise with AC PSU: 52 dBA (based on operational tests taken from bystander position [front] and performed at 27 C in compliance with ISO 7779)
Acoustic noise with DC PSU: 54 dBA (based on operational tests taken from bystander position [front] and performed at 27 C in compliance with ISO 7779)
*Roadmap
-
5Hardware Specifications Switching Engine Model: Store and forward 2 GB DRAM on each SRE 2 GB on-board flash on each SRE 1.2 Ghz dual-core CPU on each SRE 4 10GbE uplink ports on each SRE
Layer 2 Switching Maximum MAC addresses per system: 32,000 Jumbo frames: 9,216 bytes Number of VLANs: 4,096 VLAN Spanning Tree (VST) instances: 253 Port-based VLAN MAC-based VLAN GARP VLAN Registration Protocol (GVRP) Voice VLAN Physical port redundancy: Redundant trunk group (RTG) Compatible with Per-VLAN Spanning Tree Plus (PVST+) Routed VLAN Interface (RVI) IEEE 802.1AB: Link Layer Discovery Protocol (LLDP) LLDPMedia Endpoint Discovery (LLDP-MED) with VoIP integration
IEEE 802.1D: Spanning Tree Protocol IEEE 802.1p: Class-of-service (CoS) prioritization IEEE 802.1Q: VLAN tagging IEEE 802.1s: Multiple Spanning Tree Protocol (MSTP) Number of MST instances supported: 64 IEEE 802.1w: Rapid reconfiguration of Spanning Tree Protocol IEEE 802.1X: Port access control IEEE 802.1ak: Multiple Registration Protocol IEEE 802.3: 10BASE-T IEEE 802.3u: 100BASE-T IEEE 802.3ab: 1000BASE-T IEEE 802.3z: 1000BASE-X IEEE 802.3ae: 10 Gigabit Ethernet IEEE 802.3af: Power over Ethernet IEEE 802.3x: Pause frames/flow control IEEE 802.3ad: Link Aggregation Control Protocol (LACP) IEEE 802.3ah: Ethernet in the First Mile
Layer 3 Features Maximum number of Address Resolution Protocol (ARP) entries: 16,000
Maximum number of IPv4 unicast routes in hardware: 16,000 Maximum number of IPv4 multicast routes in hardware: 8,000 Routing protocols: RIPv1/v2, OSPF, BGP*, IS-IS*, IPv6*
Static routing Routing policy Bidirectional Forwarding Detection (BFD) Layer 3 redundancy: Virtual Router Redundancy Protocol (VRRP)
Supported RFCs RFC 3176 sFlow*
RFC 2925 MIB for remote ping, trace RFC 768 UDP RFC 791 IP RFC 783 Trivial File Transfer Protocol (TFTP) RFC 792 Internet Control Message Protocol (ICMP) RFC 793 TCP RFC 826 ARP RFC 894 IP over Ethernet RFC 903 RARP RFC 906 TFTP Bootstrap RFC 2068 HTTP server RFC 1812 Requirements for IP version 4 routers RFC 1519 Classless Interdomain Routing (CIDR) RFC 1256 IPv4 ICMP Router Discovery (IRDP) RFC 1058 RIP v1 RFC 2453 RIP v2 RFC 1112 Internet Group Management Protocol (IGMP) v1 RFC 2236 IGMP v2 RFC 3618 Multicast Source Discovery Protocol (MSDP) RFC 4915 MT-OSPF RFC 3376 IGMP v3 RFC 1492 TACACS+ RFC 2138 RADIUS authentication RFC 2139 RADIUS accounting RFC 3579 RADIUS Extensible Authentication Protocol (EAP) support for 802.1x
RFC 5176 Dynamic authorization extensions to RADIUS RFC 2267 Network ingress filtering RFC 2030 Simple Network Time Protocol (SNTP) RFC 854 Telnet client and server RFC 951, 1542 BootP RFC 2131 BootP/DHCP relay agent and DHCP server RFC 1591 Domain Name System (DNS) RFC 2338 VRRP RFC 2328 OSPF v2 (edge mode) RFC 1587 OSPF not-so-stubby-area (NSSA) option RFC 2154 OSPF with digital signatures (password, MD-5) RFC 2370 OSPF opaque link-state advertisement (LSA) option RFC 3623 OSPF graceful restart RFC 2362 Physical Interface Module sparse mode (PIM-SM) (edge mode)
RFC 3569 draft-ietf-ssm-arch-06.txt PIM source-specific multicast (PIM-SSM)
RFC 2474 DiffServ Precedence, including 8 queues per port RFC 2598 DiffServ Expedited Forwarding (EF) RFC 2597 DiffServ Assured Forwarding (AF) RFC 2475 DiffServ Core and Edge Router Functions LLDP-MED, ANSI/TIA-1057, draft 08 Draft IETF PIM Dense Mode (PIM-DM) draft-ietf-idmr-pimdm-05.txt, draft-ietf-pim-dm-new-v2-04.txt
Draft-ietf-isis-wg-multi-topology-11 Multi Topology (MT) Routing in IS-IS
Draft-ietf-bfd-base-05.txt Bidirectional Forwarding Detection
Specifications (continued)
*Roadmap
-
6Security MAC limiting Allowed MAC addresses, configurable per port Dynamic ARP inspection (DAI) IP source guard Local proxy ARP Static ARP support DHCP snooping
Access Control List (ACLs) (Junos OS firewall filters) Port-based filter (PACL)Ingress and egress VLAN-based filter (VACL)Ingress and egress Router-based filter (RACL)Ingress and egress Filter entries in hardware per system: 7,000 Filter counter for denied packets Filter counter for permitted packets Ability to add/remove/change filter entries in middle of list (filter editing)
L2-L4 filters 802.1X port-based 802.1X multiple supplicants 802.1X with VLAN assignment 802.1X with authentication bypass access (based on host MAC address)
802.1X with VoIP VLAN support 802.1X dynamic filter based on RADIUS attributes 802.1X supported EAP typesMD5, TLS, TTLS, PEAP MAC authentication (RADIUS) Control plane DoS protection
High Availability Nonstop active routing (NSR)OSPF v2, RIP v2, BGP, ISIS, rGMP v1, v2, v3
Redundant, hot-swappable power supplies Redundant, field-replaceable, hot-swappable fans Graceful Routing Engine switchover (GRES) for Layer 2 hitless forwarding and Layer 3 protocols on Routing Engine failover
Graceful protocol restartOSPF, BGP Layer 2 hitless forwarding on Routing Engine failover Online insertion and removal (OIR) uplink module
Link Aggregation 802.3ad (LACP) support
- Number of link aggregation groups (LAGs) supported: 64
- Maximum number of ports per LAG: 8 LAG load-sharing algorithm, bridged or routed (unicast or multicast) traffic
- IP: S/D IP
- TCP/UDP: S/D IP, S/D port
- Non-IP: S/D MAC
Tagged ports support in LAG
QoS Layer 2 QoS
Layer 3 QoS
Ingress policing: 1 rate 2 color
Hardware queues per port: 8
Scheduling methods (egress): Strict priority (SP), shaped
deficit weighted round-robin (SDWRR)
802.1p, DSCP/IP Precedence trust and marking
Layer 2-4 classification criteria: Interface, MAC address,
Ethertype, 802.1p, VLAN, IP address, DSCP/IP Precedence, TCP/
UDP port numbers, etc.
Congestion avoidance capabilities: Tail drop
Multicast IGMP: v1, v2, v3 IGMP snooping PIM-SM, PIM-SSM, PIM-DM
Services and Manageability Junos OS CLI Out-of-band management: Serial and 10/100/1000BASE-T Ethernet
ASCII configuration Rescue configuration Configuration rollback LCD management SNMP: v1, v2c, v3 RMON (RFC 2819) Groups 1, 2, 3, 9 Network Time Protocol (NTP) DHCP server DHCP relay and helper RADIUS TACACS+ SSHv2 Secure copy System logging Temperature sensor Configuration backup via FTP/secure copy
Supported MIBs**
RFC 1155 SMI RFC 1157 SNMPv1 RFC 1905 RFC 1907 SNMPv2c, SMIv2, and Revised MIB-II RFC 2570-2575 SNMPv3, user-based security, encryption, and authentication
RFC 2576 Coexistence between SNMP Version 1, Version 2, and Version 3
RFC 1212, RFC 1213, RFC 1215 MIB-II, Ethernet-like MIB, and traps RFC 2578 SNMP Structure of Management Information MIB RFC 2579 SNMP Textual Conventions for SMIv2 RFC 2925 Ping/traceroute MIB RFC 2665 Ethernet-like interface MIB RFC 1643 Ethernet MIB RFC 1493 Bridge MIB RFC 2096 IPv4 forwarding table MIB RFC 2011 SNMPv2 for IP using SMIv2 RFC 2012 SNMPv2 for transmission control protocol using SMIv2
Specifications (continued)
** Unless explicitly specified for any particular MIB table or variables, Junos OS does not support SNMP set operations.
-
7Supported MIBs (continued) RFC 2013 SNMPv2 for user datagram protocol using SMIv2 RFC 2863 Interface MIB RFC 3413 SNMP application MIB RFC 3414 User-based security model for SNMPv3 RFC 3415 View-based access control model for SNMP RFC 3621 PoE-MIB (PoE switches only) RFC 1724 RIPv2 MIB RFC 2863 Interface Group MIB RFC 2932 IPv4 multicast MIB RFC 2787 VRRP MIB RFC 1850 OSPFv2 MIB RFC 1657 BGP-4 MIB RFC 2819 RMON MIB RFC 2287 System application packages MIB RFC 4188 STP and extensions MIB RFC 4363 Definitions of managed objects for bridges with traffic classes, multicast filtering, and VLAN extensions
RFC 2922 LLDP MIB
Troubleshooting Debugging: CLI via console, telnet, or SSH Diagnostics: Show and debug command, statistics Traffic mirroring (port) Traffic mirroring (VLAN) Filter-based mirroring Mirroring destination ports per system: 1 LAG port monitoring Multiple destination ports monitored to one mirror (N:1) Maximum number of mirroring sessions: 1 Mirroring to remote destination (over L2): 1 destination VLAN IP tools: Extended ping and trace Juniper Networks commit and rollback
Warranty Enhanced limited lifetime switch hardware warranty
Safety and Compliance
Safety Certifications CAN/CSA-C22.2 No. 60950-1 (2007) Information Technology Equipment - Safety UL 60950-1 (2nd Ed) Information Technology Equipment - Safety
EN 60950-1 (2006) Information Technology Equipment - Safety IEC 60950-1 (2005) Information Technology Equipment - Safety (all country deviations)
EN 60825-1 (2007) Safety of Laser Products - Part 1: Equipment and Requirements
Electromagnetic Compatibility Certifications EN 300386 Telecom Network Equipment EMC requirements FCC Part 15 Class A EN 55022 Class A VCCI Class A CISPR 22 Class A AS/NZS CISPR 22 Class A BSMI CNS 13438 and NCC C6357 Taiwan Radiated Emissions
Immunity EN 55024 Information Technology Equipment Immunity Characteristics
EN-61000-3-2 Power Line Harmonics EN-61000-3-3 Power Line Voltage Fluctuations EN-61000-4-2 Electrostatic Discharge EN-61000-4-3 Radiated Immunity EN-61000-4-4 Electrical Fast Transients EN-61000-4-5 Surge EN-61000-4-6 Immunity to Conducted Disturbances EN-61000-4-11 Voltage Dips and Sags
Customer Specific Requirements GR-63-Core Network Equipment Building System (NEBS) Physical Protection
GR-1089-Core EMC and Electrical Safety for Network Telecommunications Equipment
SR-3580 NEBS Criteria Levels (Level 3) ETSI EN 300 019: Environmental Conditions and Environmental Tests for Telecommunications Equipment
ETSI EN 300 019-2-1 Storage ETSI EN 300 019-2-2 Transportation ETSI EN 300 019-2-3 Stationary Use at Weather-Protected Locations
ETS 300753 Acoustic Noise Emitted by Telecommunications Equipment
Environmental Reduction of Hazardous Substances (ROHS) 5/6
Telco Common Language Equipment Identifier (CLEI) code
Juniper Networks Services and SupportJuniper Networks is the leader in performance-enabling services
that are designed to accelerate, extend, and optimize your
high-performance network. Our services allow you to maximize
operational efficiency while reducing costs and minimizing
risk, achieving a faster time to value for your network. Juniper
Networks ensures operational excellence by optimizing the
network to maintain required levels of performance, reliability, and
availability. For more details, please visit www.juniper.net/us/en/
products-services.
Specifications (continued)
-
81000390-002-EN Aug 2011
Copyright 2011 Juniper Networks, Inc. All rights reserved. Juniper Networks, the Juniper Networks logo, Junos, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. All other trademarks, service marks, registered marks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice.
EMEA Headquarters
Juniper Networks Ireland
Airside Business Park
Swords, County Dublin, Ireland
Phone: 35.31.8903.600
EMEA Sales: 00800.4586.4737
Fax: 35.31.8903.601
APAC Headquarters
Juniper Networks (Hong Kong)
26/F, Cityplaza One
1111 Kings Road
Taikoo Shing, Hong Kong
Phone: 852.2332.3636
Fax: 852.2574.7803
Corporate and Sales Headquarters
Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, CA 94089 USA
Phone: 888.JUNIPER (888.586.4737)
or 408.745.2000
Fax: 408.745.2100
www.juniper.net
Printed on recycled paper
To purchase Juniper Networks solutions,
please contact your Juniper Networks
representative at 1-866-298-6428 or
authorized reseller.
Ordering Information
MODEL NUMBER DESCRIPTION
Chassis
EX6210-S64-96P-A25 EX6210 96-port PoE+ system: 10-slot chassis with passive backplane, 1x fan tray, 1x switch routing engine with switch fabric and 4x10GbE SFP+ uplinks, 2x 48-port PoE+ line cards, 1x 2,500 W AC PSU with power cord and blanks (optics not included)
EX6210-S64-96T-A25 EX6210 96-port system: 10-slot chassis with passive backplane, 1x fan tray, 1x switch routing engine with switch fabric and 4x10GbE SFP+ uplinks, 2x 48-port RJ45 line cards, 1x 2,500 W AC PSU with power cord and blanks (optics not included)
EX6210-S64-96T-D21 EX6210 96-port system: 10-slot chassis with passive backplane, 1x fan tray, 1x switch routing engine with switch fabric and 4x10GbE SFP+ uplinks, 2x 48-port RJ45 line cards, 1x 2,100 W DC PSU with DC lugs and blanks (optics not included)
EX6210-S64-96P-A50* EX6210 96-port PoE+ system: 10-slot chassis with passive backplane, 1x fan tray, 1x switch routing engine with switch fabric and 4x10GbE SFP+ uplinks, 2x 48-port PoE+ line cards, 1x 5,000 W AC PSU with power cords and blanks (optics not included)
EX6210-CHAS EX6210 chassis with backplane, spare
EX6210-FAN EX6210 fan tray, spare
EX6210-FLTR EX6210 filter, spare
Line Cards
EX6200-48P EX6200 48-port 10/100/1000BASE-T PoE+ line card
EX6200-48T EX6200 48-port 10/100/1000BASE-T RJ-45 line card
Routing Engines
EX6200-SRE64-4XS EX6200 Switch and Routing Engine including 4x 10GbE SFP+ uplinks (optics not included)
Power Supplies
EX6200-PWR-AC2500 EX6200 2,500 W AC Power Supply at 220 V (1,250 W at 110 V), power cord not included
EX6200-PWR-DC2100 EX6200 2,100 W DC Power Supply, power cord not included
EX6200-PWR-AC5000* EX6200 5,000 W AC Power Supply at 220 V (2,500 W at 110 V), power cords (2x) not included
MODEL NUMBER DESCRIPTION
Software
EX6200-AFL EX6200 Advanced Feature License
Optics and Transceivers
EX-SFP-10GE-USR SFP+ 10GbE Ultra Short Reach optics, 850 nm for 10 m on OM1, 20 m on OM2, 100 m on OM3 multimode fiber
EX-SFP-10GE-SR SFP+ 10GBASE-SR 10GbE optics, 850 nm for up to 300 m transmission on multimode fiber-optic (MMF)
EX-SFP-10GE-LRM SFP+ 10GbE LRM optics, 1,310 nm for 220 m transmission on MMF
EX-SFP-10GE-LR SFP+ 10GBASE-LR 10GbE optics, 1,310 nm for 10 km transmission on single mode fiber-optic (SMF)
EX-SFP-10GE-ER SFP+ 10GBASE-ER 10GbE optics, 1,550 nm for 40 km transmission on SMF
EX-SFP-1GE-SX* SFP 1000BASE-SX GbE optics, 850 nm for up to 550 m transmission on MMF
EX-SFP-1GE-LX* SFP 1000BASE-LX GbE optics, 1,310 nm for 10 km transmission on SMF
EX-SFP-1GE-LX40K* SFP 1000BASE-LX GbE optics, 1,310 nm for 40 km transmission on SMF
EX-SFP-1GE-LH* SFP 1000BASE-LH GbE optics, 1,550 nm for 70 km transmission on SMF
EX-SFP-1GE-T* SFP 1000BASE-T 10/100/1000 Copper Transceiver Module for up to 100 m transmission on Cat5
About Juniper NetworksJuniper Networks is in the business of network innovation. From
devices to data centers, from consumers to cloud providers,
Juniper Networks delivers the software, silicon and systems that
transform the experience and economics of networking. The
company serves customers and partners worldwide. Additional
information can be found at www.juniper.net.
*Roadmap