ethernet | fiber | coax poe & ip solutions featured ip

More than just power.™2

Features:

- Eliminates the need for a licensed electrician, providing tremendous savings by using low-voltage installation and wiring methods. - Built-in lithium iron phosphate (LiFePO4) battery charger, for optimized backup. - Designed to stack with Altronix sub-assemblies via 8-pin connection saving valuable enclosure space- Operates with Altronix midspan/injectors such as NetWay1BT, NetWay4BT or NetWay8BT.- Design a Trove access system with Tango and save more on installation and labor costs.

Leverage 802.3bt PoE to power your access system,eliminating high voltage and reducing overall cost.

PoE DrivenPower Supply/Charger Board

TANGO1B - Utilizes 4PPoE (802.3bt) to simultaneously deliver 12VDC and 24VDC- Provides up to 72W for access devices.- Can be powered by an 802.3bt PoE power source up to 90W.

PoE Driven Access Power

LiFePO4 Battery

BTL125- 12VDC / 4.5A Lithium Iron Phosphate Battery- Longer cycle life (greater than 5,000).- Up to 99% efficiency, allowing faster charging with minimal loss.- Lower self-discharge rate.

- Reduces service calls and maintenance.- 10 year shelf life.- Up to 40% more up time vs. an equivalent sized sealed lead acid battery.- Single battery saves space, cost, weight and labor.

3altronix.com

PoE Driven Access Power

IEEE 802.3bt90W Input

Power & BatteryReporting

12VDC devices

24VDC devices

LiFePO4Battery

DataPass-thru

8-Pin Connector for use with compatible Altronix sub-assemblies

Revolutionizing the Power of Access Control!Now power your access system with 4PPoE, 802.3bt...


PoE Driven Access Power Series

Features:

- Eliminates the need for a licensed electrician, providing tremendous savings by using low-voltage installation and wiring methods.- Equipped with stackable sub-assemblies, saving valuable space.- Output voltage is individually selectable by output- Individual bi-color voltage LEDs provide instant visual verification - Built-in lithium iron phosphate (LiFePO4) battery charger for optimized backup.- Operates with Altronix midspan/injectors such as NetWay1BT, NetWay4BT or NetWay8BT - up to 90W.- Enclosure (15.5”H x 12.5” W x 4.5”D) accommodates single LiFePO4 battery

Access Power Controller with PoE DrivenPower Supply/Charger

TANGO8A - Utilizes 4PPoE (802.3bt) to simultaneously

deliver 12VDC and 24VDC. - 8-trigger inputs and 8-fuse protected access control outputs.- Provides up to 65W for access devices.TANGO8ACB - TANGO8A with PTC protected outputs

Access Power Controller with Multi-Output PoE Driven Power Supply/Charger

TANGO8AP - Utilizes 4PPoE (802.3bt) to simultaneously deliver 12VDC and 24VDC.- 8-trigger inputs, 8-fuse protected access control outputs and 8-fuse protected power outputs.- Provides up to 65W for access devices.TANGO8APCB - TANGO8AP with PTC protected outputs

Multi-Output PoE Driven Power Supply/Charger

TANGO8P - Utilizes 4PPoE (802.3bt) to simultaneously deliver 12VDC and 24VDC. - 8-fuse protected power outputs.- Provides up to 72W for access devices.TANGO8PCB - TANGO8AP with PTC protected outputs

TANGO8AP

5altronix.com

Single Port 802.3bt Injector

NETWAY1BT - Single port provides 90W of total power- Additional 56V/90W Aux power output - 10/100/1000 Ethernet port - 115VAC/230VAC input (line cord)

Features:

- Supports PoE (802.3af) and PoE+ (802.3at) and Hi-PoE (802.3bt) devices up to 100m over CAT5e/6. - 10/100/1000 Ethernet ports- Embedded LINQ™ Power Management Technology, control, monitor and report power/diagnostics from anywhere over the network. - Built-in battery charging (RE2 - optional rack mount battery enclosure) - 115VAC/230VAC input (line cord)- Compact 1U EIA 19” rack mount chassis.- UL Listed in the U.S. and Canada, CE Approved.

Managed 802.3bt Midspan/Injectors

NETWAY4BT - Supports up to four (4) powered devices.- 90W full power per port (480W of total power)

NETWAY8BT - Supports up to eight (8) powered devices.- 90W full power per port (480W of total power)

Support the latest 802.3bt access,surveillance devices as well as LED Lighting...

®

802.3bt 4PPoE Solutions

Data to Switch

To any 802.3bt device suchas PoE/LED lighting, IP camera, etc..or 90W to power Tango Boardfor a plug and play access system

115/230VAC input (line cord)


802.3bt 4PPoE & Fiber Solutions

802.3bt Media Converter/Injector

NETWAYSP1BT - Single PoE port provides 90W of total power - Data option: 1Gb SFP port or 10/100/1000 Ethernet port - 48-56VDC input (95W)- CE Approved.

Features:

- Supports PoE (802.3af) and PoE+ (802.3at) and Hi-PoE (802.3bt) devices up to 100m over CAT5e/6. - Data option: 1Gb SFP port or 10/100/1000 Ethernet port - 115VAC/230VAC input.- CE Approved.

Outdoor 802.3bt Media Converter/Injectors with Integral Power

NETWAYSP1BTWP - Single PoE port provides 90W of total power. - Built-in battery charging.- NEMA 4/4X IP66-11 rated enclosure.

NETWAYSP1BTWPX- Single PoE port provides 90W of total power. - Built-in battery charging.- Large NEMA 4/4X IP66-11 rated enclosure accommodates batteries.

Outdoor 802.3bt Media Converter/Injector

NETWAYSP1BTWPN- Single PoE port provides 90W of total power.- Compact NEMA 4/4X IP66-11 rated enclosure.- Powered via NetWaySP4P for composite/hybrid cable applications.

Support the latest 802.3bt access and surveillance devices at longdistances utilizing single/multi-mode Fiber or composite cable...

NETWAYSP1BTWP

NETWAYSP1BT

802.3bt(90W) device

Data:FiberorEthernet

48-56VInput

802.3bt 4PPoE & Fiber Solutions802.3bt 4PPoE & Fiber Solutions802.3bt 4PPoE & Fiber Solutions

7altronix.com

PoE Switches with Integral Power

- Includes Outdoor NEMA4/4X rated enclosure PoE+ Switch and 75W power supply/charger- Deploy with single or multi-mode fiber as well as composite cable.- One (1) or Two (2) Gigabit SFP (Fiber) ports Compatible with Altronix SFP modules: P1MM (multi-mode), P1SM10 (single mode), P1AB2K (single strand) or P1GCE (copper)- Three (3), four (4) or eight (8) 10/100/1000 Mbps Ethernet ports.- 75W total power (max).- IEEE 802.3at (30W), IEEE 802.3af (15W) compliant or Hi-PoE (60W). - Supports 12V LiFePO4 (lithium iron phosphate batteries only (BTL125).

- Battery terminals can be utilized as a 12VDC Aux. output rated @ 800mA, when battery backup not used.- Automatic switch over to stand-by battery when AC fails.- Embedded LINQ™ Power Management Technology, control, monitor and report power/diagnostics from anywhere over the network.- UL Listed in the U.S. and Canada.- CE Approved.- Backed by a Lifetime Warranty & Proudly Made in the U.S.A.- Large outdoor NEMA4/4X rated outdoor enclosure with battery shelf: 17.53”H x 15.3”W x 6.67”D (Optional PMK2 Pole Mount Kit available)

Managed Hardened PoE+ Switcheswith Optimized Lithium Iron Phosphate (LiFePO4) Battery Charger

Features:

Model Number SFP Ports PoE/PoE+ Ports Hi-PoE Ports Total Power

NETWAYSP3LWPX 1 3

1 75W(not to exceed)

NETWAYSP4LWPX 2 4NETWAYSP8LWPX 2 8NETWAY4EWPX 1 4


PoE Switches & Media Converters

Stand-byBatteries

115/230VACInput

DataNetWaySP4P- Front Panel

Data & PoE30W/60W

Wi-fi Access Point orMicrowave Transceiver

CopperComposite Cable(Fiber & Power) Fiber

PoE HardenedSwitch

Hardened PoE+ Switches

NETWAYSP3WPN - One (1) Gb SFP port (uplink).- Two (2) ports up to 60W and 1 port up to 30W (10/100/1000 each).- Input: 48-56VDC.- NEMA 4/4X IP66-11 rated enclosure.

NETWAYSP4WPN - Two (2) Gb SFP ports (uplink).- Four (4) ports up to 30W or two (2) ports up to 60W (10/100/1000 each).- NEMA 4/4X IP66-11 rated enclosure.- Input: 48-56VDC.

Deploy PoE Switches with single/multi-mode fiber or composite (hybrid) cable.

4-Port Ethernet to Fiber Media Converterwith Built-in Power Supply/Charger

NETWAYSP4P- 120W max per output (240W total).- Four (4) Gigabit SFP ports (uplink).- Built-in battery charger (RE2 - optional rack mount battery enclosure).- AC power LED indicator.- 115VAC/230VAC input.

9altronix.com

Ethernet over Coax

Compatible Transceivers for eBridge800E:

eBridge100TM - Single port hardened Transceiver. Dimensions: 2.5”W x 3.8”D x 1”H eBridge100ST - Single port hardened mini-Transceiver.- More compact design for tighter spaces Dimensions: 2.27”W x 2.645”D x 1.12”H

Features:

- Deploy IP cameras/edge devices up to 300m (100Mbps) over coax without repeaters.- Eliminates the costs and labor associated with installing new network cabling.- Embedded LINQ™ Power Management Technology, control, monitor and report power/diagnostics from anywhere over the network. - Built-in battery charging (RE2 - optional rack mount battery enclosure) - 115VAC/230VAC input.- Compact 1U EIA 19” rack mount chassis.- UL Listed in the U.S. and Canada, CE Approved.

Deploy IP devices over coax, reducing labor and costs.

8-Port EoC Receiver with Integral PoE Switch

EBRIDGE800E - Eight (8) 100Mbps coax ports- Two (2) Gigabit Uplinks- 30W full power per port (240W of total power) - Generates PoE/PoE+ up the coax to an eBridge100ST/eBridge100TM transceiver.

EoC Adapters

EBRIDGE100STR (kit) - Single port adapter kit includes an eBridge100RM Receiver and an eBridge100ST compact Transceiver.

Receivers:EBRIDGE100RM - Single port Receiver.

EBRIDGE400PCRM - Four (4) port Receiver.

Compatible Transceivers:EBRIDGE100TM - Single port hardened Transceiver.- Also supports CAT5e up to 500m. Dimensions: 2.5”W x 3.8”D x 1”HEBRIDGE100ST - Single port hardened mini-Transceiver.- More compact design for tighter spaces. Dimensions: 2.27”W x 2.645”D x 1.12”H

EBRIDGE800PCRM - Eight (8) port Receiver.

EBRIDGE1600PCRM - Sixteen (16) port Receiver.


Long Range Ethernet

Features:

- Deploy IP cameras/edge devices up to 500m over CAT5e/6.- Passes PoE/PoE+ generated from midspan/endspan. - Data rate 100Mbps full duplex.- Supports PoE (802.3af) and PoE+ (802.3at) devices. - Receivers available with 1, 4, 8 or 16 ports.- UL Listed in the U.S. and Canada, CE Approved.

Extend Ethernet range 5x the distance - without repeaters.

Long RangeEthernet Adapters

PACE1PRMT (kit) - Single port adapter kit includes a Pace1PRM Receiver and a Pace1PTM Transceiver. Also supports single UTP up to 150m. PACE1STR (kit) - Single port adapter kit includes a Pace1PRM Receiver and a Pace1ST/Pace1PTM Mini Transceiver.

Receivers:PACE1PRM - Single port Receiver.

PACE4PRM - Four (4) port Receiver.

Compatible Transceivers:PACE1PTM - Single port hardened Transceiver.- Also supports single UTP up to 150m.PACE1ST - Single port hardened mini-Transceiver.- More compact design for tighter spaces.

PACE8PRM - Eight (8) port Receiver.

PACE16PRM - Sixteen (16) port Receiver.

Pace1PRMReceiver

CAT5e or higher

Transmits data and passes PoE/PoE+(500m - 100Mbps full duplex)

Pace1PTMTransceiver

PoE Switchor Midspan

PoE/PoE+Camera

E/PoE+

11altronix.com

Network Power Management

Benefits:- Embedded in myriad products which allows the ability to monitor control and report power diagnostics across the network locally or remotely.

- Improves service department profitability

- Health monitoring diagnostic

- Predictive maintenance

- Remote service capabilities

- Create recurring revenue stream with managed services

Report System Diagnosticsvia Email or LINQ™ Dashboard

MonitorInput & Output

Voltage & Current

Battery Health Monitoring

Unit TemperatureMonitoring

Manage MultipleDevices at Multiple Sites

Control Outputs& Reset Devices

Event LogTracks History

Cyber Secured

™


Network Power Management

Dual Input NetworkAccess Power Controller

LINQ8ACM- Eight (8) programmable Access Control System trigger inputs (NO, NC and/or open collector sink)- Eight (8) selectable 12VDC or 24VDC independently controlled outputs. (Fail-Safe and/or Fail-Secure power outputs, relay outputs or both)- Outputs are selectable to follow power input 1 or input 2.- Eight (8) auxiliary power outputs (unswitched). - Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the eight (8) outputs.

LINQ8ACMCB- LINQ8ACM with PTC protected outputs.

Features:

- Route power to a variety of access control hardware devices. - Stackable mounting configuration saves valuable enclosure space.- Output voltage is individually selectable by output.- Individual bi-color voltage LEDs provide instant visual verification.- The pluggable design allows for seamless connection to the VR6 and other compatible sub-assemblies.- Selectable voltage allows for wider range of lock options.- Easily daisy chain multiple boards to accommodate larger systems.

Network Features:

- Eight (8) individual programmable outputs: Fail-Safe and Fail-Secure, Input mode or Manual control Voltage and current reporting, Power cycle mode, Timer Scheduler, FACP override, Battery backup

- 8-Individual Programmable Inputs: Control one or more outputs- Power supply monitoring (2-power supplies): Voltage and current monitoring, Programmable voltage and current threshold

- Battery Monitoring (2-batteries): Voltage monitoring, Programmable voltage threshold, battery service notification

Facilitate remote management of access control deployments,reducing system downtime.

13altronix.com

Customize your access control with the industry’s leading manufacturers.

Features:

- Trove™ let you easily integrate Altronix power/accessories with access controllers from the industry’s leading manufacturers: AMAG, BOSCH, CDVI, DMP, FEENICS, HARTMANN, HID/VERTX, HONEYWELL, ICT, JOHNSON CONTROLS, KANTECH, KEYSCAN, MERCURY, LENEL-S2, PAXTON, PDK, SALTO, SIELOX, SOFTWARE HOUSE, ZK-TECO...and more.- Removable backplanes allow you to confi gure and test prior to on-site installation.- Simplifi es board layout and wire management, reducing installation time and costs.- Convenient knockout confi guration.- Accommodates stand-by batteries.- Includes cam lock, tamper switch and mounting hardware.

Pre-assembled wall and rack mount kits with Altronix power/accessoriesare available.

TROVE1 Enclosure Dimensions: 18”H x 14.5”W x 6.25”DBackplane Dimensions: 16.625”H x 12.5”W x 0.5”D

TROVE2 Enclosure Dimensions: 27.25”H x 21.5”W x 6.5”DBackplane Dimensions: 25.375”H x 19.375”W x 0.5”D

TROVE3 Enclosure Dimensions: 36.12”H x 30.125”W x 7.06”DBackplane Dimensions: 34.0”H x 28.0”W x 0.5”D

Access & Power Integration



Z BracketIncluded - facilitates wiring

Cam Lock

2U Drawer on extendable rails for easy access

Line Cord

Front view

Rear view

Power LEDs

Easily integrate Altronix power/accessories with a host of access control brands – saving valuable space!

3.375” x 19” x 24”(rails extend to 36”)

The Altronix Trove Rack Mount Series accommodates access controllers from leading manufacturers, expanding versatilitybeyond wall-mount configurations: AMAG, CDVI, HID/VERTX, HONEYWELL, MERCURY, LENEL-S2, SOFTWARE HOUSE...and more.

15altronix.com


Outdoor access solution ideal for vehicle/pedestrian gate access & more!

Stainless steel continuous hinge and stainless steel pad-lockable latches

*Boards sold separately

Removable backplane facilitatesthe ability to configure and test prior to on-site installationLightweight NEMA 4/4X, IP66-11 Rated

enclosure for outdoor use

Customized backplane

Outdoor Enclosure + Backplane

TROVE1M1WP• Accommodates the following Mercury/Lenel-S2 boards with Altronix power/accessories: - Mercury: EP1501, EP1502, EP2500, EP4502, MR16IN, MR16OUT, MR50, MR51e, MR52, MUX8 - Lenel-S2: LNL-1100, LNL1200, LNL-1300, LNL-1300e, LNL-1320, LNL-2210, LNL-2220, LNL-4420, LNL-8000• Dimensions: 17.53” x 15.3” x 6.67”

TROVE1WPX• Completely customizable with mounting magnets (MM series) to accommodate any access controller board with Altronix power/accessories.• Dimensions: 19.31” x 17.31” x 9.58”

PMK2• Altronix pole mount kit


Mercury/Lenel-S2 Access Enclosures

TM250- Supports a single Altronix power supply/charger with various combinations of select Mercury/Lenel-S2 boards for access systems. • Up to two (2) EP1501 or MR51e.- Accommodates up to two (1) 12VDC/4AH battery.- Includes cam lock, tamper switch, and mounting hardware.

TM400- Supports various combinations of select Mercury/Lenel-S2 boards for access systems: • Up to three (3) MR50. • One (1) EP1501 or MR51e • One (1) EP4502, EP1502, MR52, MR16IN or MR16OUT.- Accommodates up to two (2) 12VDC/7AH batteries.- Includes cam lock, tamper switch, and mounting hardware.


Compact enclosures for single door access control applications...

17altronix.com

Mounting Magnets

MM4 (4-pack)- Now customize any Altronix metal enclosure or backplane to accommodate power supplies, distribution boards, access controllers and accessories.- Easy, fast installation saves time and labor, no drilling/welding required - Can be reused and repositionedMM8 (8-pack)MM12 (12-pack)MM24 (24-pack)

Access Control Accessories

5-Port Switch Board

NETWAY5B- 5-port switch ideal in Trove series units utilizing a single network cable to connect up to four (4) network devices, reducing material and labor costs.- Mounts on side of enclosure with BR1 bracket or mounting magnets (MM4)- Input options of PoE, 12VDC or 24VDC.- Five (5) 10/100/1000 Ethernet ports.- PoE IEEE 802.3af (15W) and PoE+ IEEE 802.3at (30W) compliant.

Simplify system design and deployment with Altronix access control accessories.

Add-on Mounting Bracket

BR1- Accommodates a single sub-assembly on the enclosure’s side wall, saving valuable space: PD4UL(CB), PD8UL(CB), ACM4(CB), MOM VR6, PDS8(CB), NetWay5B or LINQ8PD(CB.- Custom made to fit Altronix enclosures for additional sub-assemblies.

Wire Magnet / Cable Tie Mounts

WM5 (5-pack)- Ideal for wire management in Trove series enclosures.- Zip-tie slot rotates 360°- Easy, fast installation saves time and labor, no drilling/welding required.- Can be reused and repositioned.WM25 (25-pack)WM100 (100-pack)


Access Power Controllers

MAXFIT3F8AP - 12VDC or 24VDC at 6A distributed via 8-fuse protected outputs. - 8-independantly controlled fuse protected relayed outputs

MAXFIT3F8APCB - MAXFIT3F8AP with PTC protected outputs

MAXFIT5F8AP - 12VDC at 10A distributed via 8-fuse protected outputs. - 8-independantly controlled fuse protected relayed outputs

MAXFIT5F8APCB - MAXFIT5F8AP with PTC protected outputs

MAXFIT7F8APS - 12VDC or 24VDC at 9.7A distributed via 8-fuse protected selectable outputs. - 8-independantly controlled selectable fuse protected relayed outputs.

MAXFIT7F16PS- 12VDC or 24VDC at 9.4A distributed via 16-fuse protected selectable outputs. - 16-independantly controlled selectable fuse protected relayed outputs.

Multi-Output Access Power Controllers

Proven power and control in a more compact, economical enclosure.

Features:

- Single power supply/charger kits equipped with Altronix sub-assemblies to facilitate access control and security devices. - Additional Class 2 power-limited Aux output(s) rated @ 1A.- Supervised fire alarm disconnect.- AC fail, low battery and battery presence monitoring.- Built-in 30-50% faster charger for sealed lead acid or gel type batteries.- Low power cutoff - protects stand-by batteries from deep discharge. - Network ready: Add LINQ2 network communication module to control, monitor and report power/diagnostics.- Enclosure (20.5”H x 16.5”W x 6.25”D) accommodates up to four (4) 12VDC/12AH batteries.

All MaxFit models available with PTC protected outputs.

19altronix.com

MAXFIT3FE - 12VDC or 24VDC at 6A

MAXFIT5FE - 12VDC at 10A

MAXFIT7FE - 24VDC at 10A

MAXFIT11FE - 12/24VDC at 4A and 12/24VDC at 4A



MAXFIT35FE - 12/24VDC at 6A and 12VDC at 10A

MAXFIT37FE - 12/24VDC at 6A and 24VDC at 10A

MAXFIT55FE - 12VDC at 10A and 12VDC at 10A



Features:

- Single and dual output power supply/chargers with room to expand, accommodating multiple Altronix sub-assemblies to meet your requirements. - Additional Class 2 power-limited Aux output(s) rated @ 1A.- Supervised fire alarm disconnect.- AC fail, low battery and battery presence monitoring.- Built-in 30-50% faster charger for sealed lead acid or gel type batteries.- Low power cutoff - protects stand-by batteries from deep discharge - Network ready: Add any LINQ™ network communication module. - Enclosure (20.5”H x 16.5”W x 6.25”D) accommodates up to four (4) 12VDC/12AH batteries.

Single Power SupplyExpandable Power Systems

Dual Power Supply Expandable Power Systems

Expandable Power Systems

Providing system designers with optimum power choices and more versatility.Customize your power system with Altronix

sub-assemblies:

ACM4/ACM8/ACMS8Access Power Controllers

PD4/PD8/PDS8/PD16Power Distribution

LINQ8PD/LINQ8ACMNetwork Communication

VR6Stackable Voltage Regulator

MOM5Power Distribution with FAI

ethernet | fiber | coax poe & ip solutions featured ip

Documents