concrete faÇade framing systems -...
TRANSCRIPT
PG 14 - E
FAÇADE
FRAMING SYSTEMS
CONCRETE
DEMU Fixing anchors
HMS - Brick Tie Channels
HTU Cast-In Channels
HTA Cast-In Channels
HGB - Balustrade Fixings
HTA-CSCurved Solutions
Channels
HZA - DYNAGRIP Cast-In
Channels
HALFEN Framing System/Accessories
HALFEN Framing Channels and HALFEN Bolts
HBS-05 Screw Connections
MBT Reinforcement Coupler
HBT Rebend Connections
HDB Shear Rails
HIT Iso-ElemenT
HBB bi-Trapez-Box ®
HCC Column Shoe
HSC Stud Connector
HTT/HTF Impact Sound Insulation
Elements
DETAN Tension Rod System
DEHA HD-Socket Lifting Anchor
System
FPA Façade
Panel Anchors
SUK Sub Structure
HK4 Brickwork Support
System
MVA Sleeve Anchors FA Flat Anchors
UMA Grout-In Anchors
Body Anchor
FIxING SYSTEMS, FRAMING SYSTEMS AND ACCESSORIES
REINFORCEMENT SYSTEMS
LIFTING SYSTEMS, CONCRETE PRECAST SYSTEMS, NATURAL STONE SYSTEMS, BRICKWORK SUPPORT SYSTEMS, ROD SYSTEMS
Connection Solutions.The HALFEN Product range.
Paserelle Simone de Beauvoir, France
DEHA KKT Spherical Head Lifting Anchor
DEHA HA Socket Anchor
FRIMEDA TPA Lifting Anchor
System
© 2014 HALFEN · PG 14-E · www.halfen.com 3
Connection Solutions.The HALFEN Product range. HALFEN Range –
Concrete Products
4 © 2014 HALFEN · PG 14-E · www.halfen.com
HALFEN HTA CAST- IN CHANNELS
HALFEN HZA CAST- IN CHANNELS DYNAGRIP
• Concretefaçades• Precastconcreteelements• Pipesupportsystems• Brickworksupport
HALFEN HTA Cast-in channels are also
ideal for all fixings in which dynamic
loads occur, e.g. in crane rails or machine
fixings. Special hot-rolled profiles are
available for this purpose.
Particular quality features associatedwith HALFEN Channels:• European Technical Approval
ETA-09/0339
• ApprovedbytheGermanbuildingauthority (DIBt Berlin), abZ: Z-21.4-34
•Highbearingloads•Fasteningsystemforcrackedand non-crackedconcrete•Small edge distances
HALFEN Cast-in channels are the ideal
basis for easy-to-install, adjustable fixings.
A polystyrene bead filler or a strip filler
provides protection against ingress of
concrete into the channel. Any compo-
nent can be fixed to HALFEN Channels,
e.g.:
•Easytoadjust•Assemblywithoutnoiseanddirt
These quality features make HALFEN
Channels an indispensable product for
all planners and users.
HALFEN HZA Dynagrip are channels that
have the capability to carry loads in the
longitudinal direction. These high capacity
channels are even able to carry dynamic
loads of up to 15 kN.
A unique serration guarantees positive
load transmission in the channel longitu-
dinal direction.
HALFEN HZA Cast-in channels Dynagrip
fulfil all the requirements for securely at-
taching lift guide rails: Three-dimensional
load absorption with high dynamic loads.
The quality features of HALFEN HZA Cast-in channels Dynagrip:•Highresultantloadcapacityofupto
FRd = 37,8 kN in all directions. This also includes loads in the longitudinal direction
•Fasteningsystemforcrackedandnon-crackedconcrete
•Allowabledynamicloadamplitudeofup to ΔF = 15 kN
•Compactproductrangeconsistsoffour types: HZA 29/20, HZA 38/23, HZA 53/34 and HZA 64/44
•Hot-dipgalvanisedrespectivelyastainless steel design gives a high degree of corrosion protection
•ApprovedbytheGermanbuildingauthority (DIBt Berlin) for static and dynamic loads, abZ: Z-21.4-1691
5© 2014 HALFEN · PG 14-E · www.halfen.com
HALFEN HGB BALUSTRADE F IxING SYSTEM
HALFEN HMS BRICKWORK RESTRAINT SYSTEM/ML+ML1 MASONRY TIES
HALFEN HGB Channels and the suit-
able high-tensile bolts enable a safe
and statically perfect fixing of railing
posts to the surface of the concrete
slabs with a thickness of minimum
10 cm. This is possible due to the
special anchoring made of reinforce-
ment bars.
Quality features:• Adjustablefixingofrailingposts• Availableinlengthsfrom10cm
upwards•Railingandfixingwithnewcalculation
model approved by the German building authority (DIBt Berlin), abZ: Z-21.4-1912
The HALFEN Brickwork restraint
system is designed to tie all brickwork,
wall connections and external cladding
masonry (with or without cavity) by
means of HALFEN ML and ML1 ties to
concrete walls and columns or to steel
and wooden constructions.
Due to the possibility of slipping of
the brick ties within the channels, the
risk of masonry cracking is considerably
reduced. The ties hook securely into
the channels and form a closed
system.
Quality features:• Simple,inexpensivesystem• Alsosuitableforthinmortarjoints
(ML1 type)•CElabeled
6 © 2014 HALFEN · PG 14-E · www.halfen.com
With the wide range of HALFEN Channels
HTA and HZA (see page 4), HALFEN
offers technologically sophisticated
and economic solutions for almost all
anchoring applications in concrete.
Even higher demands are placed on an-
choring in safety-relevant areas, such as
nuclear power stations, than is the case
in administration, industry or residential
buildings. HALFEN has developed the
HZA-PS product range especially for these
applications. Due to the exceptional
influences, anchoring must also remain
stable in concrete constructions with
wider cracks. These higher requirements
are fulfilled by HZA-PS 29/20, HZA-PS
38/23 and HZA-PS 53/34.
Quality features:•Suitableforapplicationsinsafety-
relevant areas•FRd load bearing capacity up to
30.8kNastheresultantloadinall directions
•Highoscillationrangeupto12kN fatigue relevant loads
•Suitableforapplicationsinearthquakeareas
•Specialanchorformforsafeanchoringincrackedandnon-crackedconcrete
HTU Cast-in channels in beams or
columns are ideal to fix profiled metal
sheets with self-drilling screws, self-
tapping screws or shot fired nails. Tensile
forces due to wind suction, as well as
shearing forces to provide the panel
effect of the roof slab are taken up by
the HTU channels.
Quality features:• Loadsapplyforallloaddirections• ApprovedbytheGermanbuilding
authority (DIBt Berlin), abZ: Z-21.4-84• Availableinhot-dipgalvanised
and A4 stainless steel
HALFEN HTU CAST- IN CHANNELS
HALFEN HZA -PS CAST- IN CHANNELS
© 2014 HALFEN · PG 14-E · www.halfen.com 7
Those who choose the HALFEN Fastener
system receive not just a comprehensive
range of products with the highest
quality and technical standards, but
also competent customer support.
Chemical fasteners:Injection system HB-VMZ: The strongest
and most versatile fastener can be used
HALFEN HB ANCHOR BOLT SYSTEM
and easy to use fasteners for simple
applications in non-cracked concrete
(HB-B) or in cracked concrete (HB-BZ).
Heavy duty anchor HB-SZ: a high-
performance push-through anchor
system that allows very high authorised
loads in cracked and non-cracked
concrete at low axis and edge clearances.
Drop-in anchor HB-E: the range is com-
pleted by the drop-in anchor with thread
for pre-assembly. Suitable for use in
non-cracked concrete, commonly for the
connection of lightweight false ceilings.
HB-E is available with galvanised finish
or made from stainless steel for different
applications. Various abZ-approvals
(German General Building Approvals)
and European Technical Approvals are
available.
HALFEN TIMBER F IxINGS
Roof and wall:To secure the position and to prevent
lifting due to wind suction the timber
beams of flat roofs are put on steel con-
crete ring beams where HALFEN Channels
are cast in with flush surface according to
their load capacity. Timber connection
straps with hammer head are put in the
HALFEN Channels, pushed and nailed to
the timber beams. HALFEN Timber con-
nection straps are a simple, safe and
especially quick method of fixing.
Instead of concrete upturns used in the
past (which required a lot work in view
of formwork and reinforcement) the rafter
shoes are screwed directly on the HALFEN
Channels which are cast in the concrete
slab with flush surface. Thus, loads of
rafter and collar beam roofs with widths
of the rafter from 6 up to 12 cm and
different roof pitches can be fixed with
only one type of rafter shoe.
to carry high loads in situations with
minimal edge distances due to various
anchor depths. Suitable for use in
cracked and non-cracked concrete.
Shear connector HB-V: This classic
fastener combines an economical
solution with easy assembly for simple
connections to non-cracked concrete.
Injection system HB-VMU, injection
mortar HB-VM-ME: suitable for use
in non-cracked concrete.
Mechanical heavy duty fasteners:The HALFEN range of mechanical heavy
duty fasteners consists of state-of-the-
art systems only that fulfil the highest
requirements in safety, quality and
economy. More fasteners than these
are not required.
Bolt anchor: The HB-B and HB-BZ-Bolt
anchors are extremely economical, quick
8 © 2014 HALFEN · PG 14-E · www.halfen.com
HALFEN HBJ BETOJUSTER
The betojusterHBJ-S(columnadjuster) is used to align columns with adapted
foundation slab; can also be used for
sleeve foundations, foundations-slabs,
road slabs and for platform slabs. There
are two load groups of column adjusters
(6 t and 10 t). Bolts turned with a
socket spanner are used for adjusting.
There are two types of column adjuster
for the various methods of column
production.
1) HBJ-S-Lst.-v for vertical installation, if
the betojuster is cast in to foundations
slabs in horizontal formwork (the column
is subsequently cast to the slab).
2) HBJ-S-Lst.-h for horizontal installa-
tion of columns with upright foundation
slab cast in a single pour.
The betojusterHBJ-W(walladjusters) is used for height adjustment of con-
crete precast wall elements (interior
wall, double leaf walls) precast stair and
landing elements as well as for height
adjustment of prefabricated garages.
Adjustment is by turning the betojuster
with a ratchet-wrench.
Advantages are:• Simpledamage-freeadjustment•Optimalcraneuse•Minimaleffortrequired•Especiallysuitedfordifficult-to-access
areas
Pour hole
Fixing-tool
Pour hole
BetojusterHBJ-S
BetojusterHBJ-S
DEMU FIxING ANCHORS
DEMU Fixing anchors T-FIXX® and bolt
anchors 1988, 1985 from HALFEN
are intended to be used for a safe and
permanent anchorage of fixtures in
concrete. Different anchor dimensions
(max. thread size M42) and materials for
corrosion protection (electroplated, hot-
dipped galvanised and stainless steel)
ensure a sophisticated product range.
Examples for typical application:
– Fixing of props and connecting devices
on precast elements
– Fixing of railings for balconies and
bridges
– Fixing of utility equipment, power lines
– Fixing of steel ladders, stairs and
profiles
– Fixing of safety devices
Quality features:• WithEuropeanTechnicalApproval,
ETA-13/0222 (T-FIxx), ETA-13/0401 (Bolt anchor)
• Designmethodaccordingto current state of the art technology (CEN/TS 1992-4-1/2)
• Useinreinforcedandunreinforcedconcrete
• FixinganchorwithinternalmetricISO thread
• Fortransmissionoftensileloads,shear loads and a combination of both
• Withattacheddatachipforidentifi-cation
• Widerangeofaccessoriesforeasyassembly
9© 2014 HALFEN · PG 14-E · www.halfen.com
HALFEN HBS-05 Screw connections
offer a wide range of connector bars,
socket bars and accessories for optimal
solutions regarding both in-situ and
precast constructions.
All HBS-05 bar versions can be combined
with each other, so that a high degree
of flexibility and a greater range of
applications is achieved. The HBS-05
position sleeve enables the connection
between axially unmovable and not
turnable bars, e.g. at crane openings in
floor slabs. For connections with short
anchoring lengths, HBS-05 end anchors
are available.
Quality features:• Extensive delivery programme for
straight and bent bars with diameters ranging from 12 to 32 mm
• Colourcodingforeasyidentificationof matching components
• Approved for dynamic loads for bar diam. 12 to 28 mm
• Forgedsocketbarscanbenailed directly to the shuttering
• Boltedsocketbarsareparticularlyeconomic for vertical reinforcement connections and custom lengths
• ApprovedbytheGermanbuildingauthority (DIBt Berlin), abZ: Z-1.5-189
HALFEN HBS-05 SCREW CONNECTION
The MBT Reinforcement coupler joins
two reinforcement bars. Tensile and
compression forces are transferred.
The MBT Reinforcement coupler is
particularly suitable for the replacement
of damaged reinforcement, the connec-
tion of old and new constructions, the
connection of precast concrete units
and of high precast chimneys.
Quality features:•Safeandquickconnection•Shortcouplings•Nopreparationofbarends,nocutting
threads or welding•ApprovedbytheGermanbuilding
authority (DIBt Berlin), abZ: Z-1.5-10
HALFEN MBT REINFORCEMENT COUPLER
HALFEN HLB LOOP BOx
HALFEN HLB Loop Box – the strong
simple and economic solution for
connecting concrete elements to one
another.
Economic construction with short
assembly times, smooth processes
during construction and security after
construction – these are our concerns.
The HALFEN HLB Loop Box ensures that
walls can be erected quickly and easily
when building with pre-fabricated con-
crete wall elements. And all that with the
highest level of reliability and quality.
Quality characteristics:•Nodeformationthankstouseof sturdy sheet steel•Simplyassemblyduetopre-punched nail holes•Specialrecessformerssavetime during assembly• ApprovedbytheGermanbuilding
authority (DIBt Berlin), abZ: Z-21.8-1869, abZ: Z-21.8-1870, abZ: Z-21.8-1871
© 2014 HALFEN · PG 14-E · www.halfen.com10
HALFEN HBT REBEND CONNECTION
HBT Rebend connections are used for
efficient connection of concrete struc-
tures which are poured in subsequent
phases and have to be connected.
The casing consists of pre-galvanised
steel sheet with special flanges and
a preformed hole to facilitate the
removal of the cover from the casing.
It can be simply nailed to the formwork
or wired to the reinforcement.
HBT Rebend connections correspond
with the requirements in the ’rebend‘ fact
sheet, DBV version 2008, are type-
tested and suitable for use according
to DIN EN-1992-1-1.
Quality features:•Thereinforcementstarterbars
are made of a) B500B in accordance with DIN 488 b) B500 NR available on request,
bars Ø 8 – 12 mm•7differentcasingstosuitwall
thicknessfrom8–23cm. (Special types are available forlargerwallthickness)
•13differentbarshapesareavailablefor single or double bars
•TypetestedbytheGermantestingauthority according to DIN EN 1992-1-1, Test no.: S-WUE/110115
•Flathousingprofile: NEW: Reduced casing heights (for 8 mm bars h = 24 mm, for 10 mm bars h = 30 mm, for 12 mm bars h = 36 mm), hence ideal for precast concrete industry where elements are produced with smaller concrete coverings
© 2014 HALFEN · PG 14-E · www.halfen.com 11
HALFEN HDB SHEAR RAIL
HDB system element
HDB complete element
HDB Shear rail elements with double-
headed studs, welded to a spacer bar, are
used as punching and shear reinforcement.
They are preferably put in from the top
after laying the flexural reinforcement. The
double-headed studs are made out of rib-
bed or smooth rebars. HDB Shear rails are
supplied as HDB System elements, which
are available off stock, and HDB Complete
elements, which are manufactured on
demand according to customers require-
ments. The HDB System elements consist
of 2 stud and 3 stud elements, which
can be combined to any required layout.
The symmetrical arrangement of the
studs on each HDB System element and
the patented clip bar ensures correct in-
stallation. The HDB Complete elements
are designed with 3 and more double-
headed studs welded to a spacer bar at
individual spacings on demand. HDB
Complete elements are very suitable
for installation from “below”; i.e. the
elements are placed on the formwork
by special spacers. The lower and upper
reinforcement are then installed.
BenefitsoftheHDBShearrails:•The new European Technical Approval
ETA 12/0454 allows for a punching shear design based on EN 1992-1-1
•The same design provisions are now applicable in 28 countries
•In addition, for the application as punching shear reinforcement, Ger-man Technical Approvals issued by the German Building Authority (DIBt) are available: Z-15.1-213, Z-15.1-264
•For the application as shear reinforce-ment, German Technical Approvals is-sued by the German Building Authori-ty (DIBt) are available, which base on EN 1992 1 1: Z-15.1-270, Z-15.1-249
•The HALFEN Calculation program is a convenient tool with many features to help calculate HDB Shear rails as punch-ing shear or shear reinforcement
•TheHDBShearrailsareCEmarkedandqualitycertifiedbytheRAL control association for anchorage and reinforcement technology: RAL-GZ 658/2
12 © 2014 HALFEN · PG 14-E · www.halfen.com
HALFEN SOUND INSULATION PRODUCTS
A particular annoying form of structure-
borne noise is caused by footfall impact
noise. Insufficient impact sound insulation,
for example in staircases of apartment
blocks can be the cause of the problem.
Using the high quality Elastomeric sup-
ports and with correct placement of the
HALFEN HTPL Joint strips, the solid stair
units are acoustically separated from the
adjacent building components. HALFEN
Sound insulation products are perfectly
suited to fulfil the requirements of sound
impact insulation.
• Is available in three different load
groups for on-site casting or for
precast stair elements in conjunction
with on-site casting of stair-landings
• Available for 90 cm to 200 cm wide
stair widths
• Type tested by a German testing
authority, Test no.: S-WUE 040519
• Is available in three different load
groups for precast stair elements
used in conjunction with on-site
casting and stair-landings
• Available for stair widths from 100 cm
to 200 cm wide. Using insulation
strips or support strip width is freely
adjustable
• Superior quality bi-Trapez support
with official building approval
certificate no.: P-849.0554/1
• For on-site casting or for precast
stair elements in conjunction with
concrete or masonry walls
• Superior quality bi-Trapez support
with official building approval
certificate, Test no: P-849.0554/1
• Box is available for three stair-landing
slab heights (d=16/18/20 cm).
• Supporting element type tested
by a German testing authority,
Test no: S-WUE/040559
HALFEN HTT Impact Sound Insulation: HALFEN HTF Impact Sound Insulation: HALFEN HBB bi-Trapez-Box®:
13© 2014 HALFEN · PG 14-E · www.halfen.com
HALFEN HCC COLUMN SHOE
Conventional methods for the connec-
tion of columns to foundations are often
expensive to produce, to transport and
to handle on construction site. The
HALFEN HCC Column shoes in con-
junction with HALFEN HAB Anchor bolts
is an advantageous solution for these
problems.
HALFEN Column shoes are not only used
for connection of precast columns to
foundations, but also for rigid joint of
precast column-segments, in order to
form continuos columns independent of
floor slabs.
Quality features:• Productprogrammefor10loadsteps
rangingfrom62kNto937kN• Quickassemblytime;thefullad-
missible load capacity of the column shoe can be applied immediately after assembly
• Columnshoesaretypetested, LfB Baden-Württemberg, Test no.: Nr. 03/30
• Headedanchorbolt,approvedby the German building authority (DIBt Berlin), abZ: Z-21.5-1758, Z-21.5-1761
• Anchorboltsaresuitableforvariedanchoring of high loads
The HALFEN Shear dowel system HSD is
designed to transmit shear loads in
construction joints and therefore avoid ir-
regular settling and misalignment caused
by variable deformation. Depending on
the type chosen, horizontal movement
caused by contraction, creeping or the
effect of temperature is allowed in the
longitudinal direction or longitudinal- and
lateral directions.
Particularly high loads can be transmitted
by the HSD/CRET shear dowel system.
Quality features:•Simplegeometryofthejoint•Time-savingduetosimpleshuttering and installation•Spacegainedbyexclusionof double pin•Costsavingandspacegaineddue to construction in sections• ApprovedbytheGermanbuilding
authority (DIBt Berlin), abZ: Z-15.7-253
HALFEN HSD SHEAR DOWEL SYSTEM
14 © 2014 HALFEN · PG 14-E · www.halfen.com
HALFEN HUC UNIvERSAL CONNECTION
The HALFEN HUC Universal Connection
System is a family of components that
together provides very effective solutions
for the transfer of high structural loads
into concrete. The components of the
HUC family comprise of the HSC-B Con-
crete Steel Connection System and the
HSCC Steel Corbel System. The load range
and adaptability of these components
enables the HUC system to offer a huge
range of connection applications. These
include connections for steel beams,
steel corbels, and anchor points for both
DETAN Tension Rods and cable bracing
systems.
HSC-B Steel connection systemThe steel connection system can be
used everywhere, where a connection
between steel and concrete is needed.
By fitting on non-predominantly static
loads, the socket rods are also suitable
for crane rail systems.
HSC-S HSC-A
The HALFEN HSC Stud Connector is a
technically approved reinforcement
designed to provide powerful and
economic connections of corbels to
columns. The HSC Stud Connector from
HALFEN ensures a considerable time-
saving and extraordinary amount of
HALFEN HSC STUD CONNECTOR
flexibility when constructing concrete
columns with corbels.
Quality features:•Transferhightensileforces•100%anchoringduetoforgedhead•Speedierconstructionduetosimple assemblywithoutspecialtools; the amount of steel used is reduced considerably•Anchorheadcanbeplaced horizontally or vertically to allow the optimal use of space•Alsosuitablefornotjuststaticloads•Wallsandcolumnscanbeconcreted in one step, the corbels are subsequently attached by threaded connectors•Reliableandtime-saving•Simplearrangementofreinforcement•Solutionsformonolithicand subsequently concreted consoles•Lowcost•Completesystemforallapplications
•Convenientfreemeasurementsoft-ware for consoles, issue of a structure with parts list ready for testing
• ApprovedbytheGermanbuildingauthority (DIBt Berlin), abZ: Z-21.8-1973
HSCC Steel corbelsTo support the planning process,
HALFEN offers 34 type-tested steel
corbels for steel connections. Compared
to steel concrete corbels, the HSCC have
a bearing capacity of up to 2 times
higher. In conjunction with stepped beam
supports, very low construction heights
can be achieved.
Quality features:•GermanBuildingauthority
approval Z-21.8-1974 or type test S-WUE/110032
•Fullyfunctionalconnectionfor normal, shear forces and bending moments
•Durablewithoptionalcorrosion protection
•Nocostlyandtimeconsuming formwork
•Easymountingbyscrewing
© 2014 HALFEN · PG 14-E · www.halfen.com 15
HALFEN HIT INSULATED CONNECTION
Slab connection elements are heat-insulat-
ing elements used for thermal separation
of reinforced concrete structures. In
practice slab connections are used to
avoid mould caused by condensation,
to ensure compliance with increased
building physic requirements and also
to avoid cracks caused by thermal
expansions.
The HALFEN insulated connection HIT-HP/
HIT-SP with patented Compression Shear
Bearings is the first slab connection with
a CE mark.
Because of the ETA-13/0546 Approval
the insulated connections, the calculation
concept as well as the characteristic values
from the building design aspect can be
used in more than 30 countries in Europe
without further approval requirements.
This increases reliability in planning.
Apart from the calculation model and
other construction references, the ther-
mal bridge characteristic values (Ψ, θmin
and fRsi) as well as the difference value
(ΔLn,W) for footfall noise for a slab con-
nection element are, for the first time,
certified Europe-wide. HALFEN places a
building authority approved reference
with building physic values at the dispo-
sal of the user, the basis of which are ge-
nerally easy to understand with technical-
ly regulated details. The patented multi-
part installation and flexible combination
of the modules means that transpor-
tation and storage costs as well as CO2-
emmisions can be significantly reduced.
The method of combining the elements
increases the flexibility and planning
certainty in planning in particular for the
prefabrication industry. As standard, all
HALFEN HIT-HP/HIT-SP insulated connec-
tions are fire retardant according to REI
120, whereby the fire retardant material
is enclosed and protected in a robust
housing. Incorrect planning or insufficient
installations of the fire retardant require-
ments as well as damage to the fire retar-
dant material are therefore prevented.
This is the first time tension rods are
anchored using anchor heads in elements
for use in offset applications or wall
connection (HIT-HP/SP .. OD/OU).
This reduces the number of required
elements, simplifies application as well
as handling and results in a simpler re-
inforcement layout. The combination of
transverse load rebars and C S B in trans-
verse load connections makes maximum
utilisation of all load bearing elements
possible. The shear loads are supported
by the shear load bars as well as by the
Compression Shear Bearings. Limiting
the applicable effective shear load to
VEd ≤ 0.3 VRd,max which applies to all
slab connections, can therefore be in-
creased by the load bearing portion of
the Compression Shear Bearings. In the
standard range of application and when
considering all necessary verifications the
HIT-HP/SP-ZV offers the highest load-
carrying capacities. To facilitate calcula-
tion of the thermal characteristic values
a HIT Calculator App can be downloaded
from the HALFEN website.
Quality characteristics are:• EuropeanTechnicalApproval
ETA-13/0546 (OIB Wien). (Austrian Institute of Construction Engineering in vienna)
•Buildingauthorityapproved(DIBtBerlin) paragraph: Z-15.7-293, Z-15.7-309, Z-15.7-312 including typetestcertificates
•PassiveHouseInstitutecertifiedasanefficientthermalbridgeconstruc-tion with as little as 80 mm insulation joint,whilealsosuitableforlargeload capacities
•ConformswiththeEnEV-/Normwithbuilding authority approved characte-ristic values (Ψ, θmin, fRsi and ΔLn,W)
•AllsidedfireresistanceREI120asstandard
•Flexibleelementsystemwith separate modules
•UserfriendlySoftware•AppforcalculationofΨ-values•Sustainabilitythroughuseof
recycling material
© 2014 HALFEN · PG 14-E · www.halfen.com16
HALFEN Range – Façade Products
17© 2014 HALFEN · PG 14-E · www.halfen.com
HALFEN UMA/UHA GROUT- IN ANCHORS
HALFEN Grout-in anchor are a traditional
method of connecting natural stone
façades to load bearing structures made
of concrete or brickwork. UMA Support
anchors are used to support vertical
and horizontal forces, UHA Restraint
anchors are used to support horizontal
compression or tension forces. The
tubular section of the UMA/UHA
Anchors make them suitable for both
horizontal and vertical natural stone
panel joints.
Quality features:• Canbeusedforlargestand-off
installations (20-300 mm) and highloadsupto3,9kN
•3-dimensionaladjustabililty• Suitableforseismicloads• Numericallyqualifiedthermal
bridgecoefficient χ [W/K]•Typetested• TÜV/LGAtestedquality,
Cert. no. 71713
The HALFEN SUK System is an adjustable
suspended channel system with support
and restraint anchors that are continuously
variable in height, for cavities > 160 mm.
It is ideal for new builds and refurbish-
ments. It is particularly suited for natural
stone façades with large and varying
distances to the load bearing wall. The
system is easy to install with few simple
components.
Quality features:• StainlesssteelA4• Easyandquickinstallation• Spansnon-loadbearingsubstrate• Highloadcarryingcapacity• AdjustablefasteningtoHALFEN
Channelsformaximumadjustment• Highcorrosionresistance
HALFEN SUK
18 © 2014 HALFEN · PG 14-E · www.halfen.com
The HALFEN Curtain wall support
system provides adjustable support
for framed façade systems. Adjustable
brackets used in conjunction with
HALFEN Channels provide a fast and
simple method of restraining both the
weight and wind loads imposed on the
façade. The system may be used on either
steel frame or conventional concrete
frame structures, and is available in
different designs to enable rapid mullion
installations to either the top or edge of
floors and beams.
Quality features:• Fastandsafefixing,allowing
immediate full load application• Installedwithoutspecialtools• Nopowersupplyrequiredfor
installation• Easyadjustmentinuptothree
directions• Highloadbearingcapacities• Closeedgedistances
HALFEN HCW CURTAIN WALL SYSTEM
3-dimensional adjustable HALFEN Body an-
chors are used for connecting natural stone
façades to load bearing structures made of
concrete or brickwork. They are fixed using
HALFEN Anchor bolt systems. HRM/HRC,
BA or DT are support anchors for dead
loads and wind loads, DH Restraint an-
chors are used to support horizontal com-
pression or tension forces (wind). The ad-
justment is partly possible under load.
HALFEN HRM Body anchors are used for
maximum permissible loads up to 500 N
and projections between 40 and 130 mm.
HALFEN BA Body anchors are designed
for small projections of 60 to 120 mm
with a maximum load of 1300 N.
HALFEN DT Body anchors are suitable for
large projections of 140 to 300 mm and
high loads up to 1300 N. The pre-assem-
bled anchor consisting of the bracket, the
adjustable wedge plate and a clamping
bolt is supplied ready to be installed.
HALFEN DH Body anchors are used in
horizontal or vertical joints in combination
with HALFEN HRM/HRC, BA or DT Body
anchors.
Quality features:• Forstand-offinstallationsfrom30‒
300mmandloadsupto1,3kN•3-dimensionaladjustabililty•Anchorsareadjustablethrough15°• Canbesubjectedtoloadimmediately
after installation•Usedinverticalorhorizontaljoints• Numericallyqualifiedthermalbridge
coefficientχ [W/K]• TÜV/LGAtestedquality,
Cert. no.: 71712
HALFEN BA/HRM/DT/DH BODY ANCHORS
19© 2014 HALFEN · PG 14-E · www.halfen.com
HALFEN HK4 BRICKWORK SUPPORT
The HALFEN HK4 Brickwork support
system is used for absorbing the dead
load of brickwork and its transfer to the
structure walls of the building.
With their high degree of vertical adjust-
ment of ± 3,5 cm they are very well suit-
able to balance existing tolerances in the
structure or inaccuracy in the installation
of dowels.
The HK4 Brickwork support system is
available in stainless steel in various
versions to cope with a wide range of
support applications.
The different load capacities of 3.5 kN,
7.0 kN and 10.5 kN in connection with
HALFEN Channels are an economic
way of supporting brickwork.
Quality features:• Completeproductrangeforbrickwork
construction•Verygoodadjustmentoptions•Type-testreportS-WUE080272• ApprovedbytheGermanbuilding
authority (DIBt Berlin), abZ: Z-21.8-1992 forthenotchedU-Bracket
•CEmarked•Freedesignsoftware
HALFEN BRA PARAPET CORBELS
Parapet corbels are used to fix precast
parapet or attic panels to reinforced
concrete slabs, balconies or wide
columns.
They are cast into the precast parapets
and transported to site. Their load be-
havior is characterized by the absorp tion
of bending moments. When fixing them
to cast-in HALFEN Channels, the anchors
can be moved horizontally, and they can
be adjusted vertically using spacers.
Parapet corbels are also available with
adjustable bolts for the vertical adjust-
ment.
Quality features:• Reducedthermalbridging• Designedinstainlesssteelfor
high corrosion protection• Veryfastinstallation• Type-testreportS-WUE 050196
20 © 2014 HALFEN · PG 14-E · www.halfen.com
The HALFEN Sandwich panel system
comprises support-anchors (sleeve
anchors or flat anchors) and restraint
ties (connector pins, clip-on pins or stirrup
ties).
Quality features of the SP-MvA: •Onlyonesupportanchorrequired
per slab•Wellprovensystem,approvedby
the German building authority (DIBt Berlin), abZ: Z-21.8-1979
•Fastinstallation
Quality features of the SP-FA: •Highloadcapability•Alsosuitableforlargedimensions
units•Wellprovensystem,approvedby
the German building authority (DIBt Berlin), abZ: Z-21.8-1979
•Simplestaticsystemwithtwo support anchors
HALFEN SP -SPA WIRE SANDWICH PANEL ANCHOR
HALFEN Wire sandwich panel anchors are
used to join the load bearing and the
front panel in a multilayer concrete faça-
de slab. They transfer the dead weight of
the front panel as well as the stresses on
it to the load bearing panel. As the an-
chors are exposed to corrosion in the
area of the air gap and the insulating la-
yer, they are made of stainless steel. In
addition to load bearing anchors, ties or
pins are used to prevent deformation of
the front panel and for wind loads.
Quality features:•Easyandquickinstallation•Wellprovensystem,approvedby
the German building authority (DIBt Berlin), abZ: Z-21.8-1926
•Canalsobeusedforverythick insulating layers between the concreteskins
•Measurementsoftwarereadyfor testing
•Lowheattransfer
HALFEN SP -MvA SLEEvE ANCHORSHALFEN SP -FA FLAT ANCHORS
21© 2014 HALFEN · PG 14-E · www.halfen.com
The DETAN Rod system is used to
design:
– Wind bracings in roofs and walls,
– Pylon and canopy restraints,
– Ties for wood and steel beams,
– Glass facade supports,
– Pedestrian bridge suspensions
System solutions help to realize complex
constructions and interesting designs for
internal and external areas. All compon-
ents are available in steel and stainless
steel.
Quality features:•Fulfilssophisticateddesignrequirements•Simplevisualcheckofinstallation•Pre-assembleddeliveryuptoØ60mm•Hydraulicpre-tensiondeviceavailable•Crosscoupleraseconomicalternative
to the circular disc •Europeantechnicalapprovals
ETA-05/0207 and ETA-11/0311•Type-test reports S-WUE 060382 and
S-WUE 120315 acc. to EC 3 •CEmarked•Freedesignsoftware
DETAN ROD SYSTEM
tension rod
locking nut
fork end
pin
circlip
anchor disk
The façade anchor system consists of
an upper section with a vertically
adjustable threaded rod and a lower
section cast into the panel allowing
horizontal adjustment. All system
components are made of stainless steel.
Additional accessories of this product
range include spacer bolts, wind anchors
made of plastic or stainless steel, turn-
buckle restraint, HKZ Restraint ties and
adjustable restraints.
Quality features:•Simpleandquickinstallation•Adjustableinalldirections•ApprovedbytheGermanbuilding
authority (DIBt Berlin), abZ: Z-21.8-1910
•Loadlevelsfrom5to56kN/anchor
HALFEN FPA FAÇADE PANEL ANCHORS
22 © 2014 HALFEN · PG 14-E · www.halfen.com
The new generation HD-Socket lifting
system with protective cap and integrated
identification cap covers the load range
up to 25 tonnes with only nine load
groups. The anchor sleeve is also
available in stainless steel. The anchor
sleeve protection system remains
permanently in the sleeve and offers
protection against all type of dirt.
Quality features:•Concise product range for load groups
from 1,3 up to 25,0 •Integrated sleeve protection (patent)
with data clip•Robustliftingclutchforincreased
safety and economy•Theliftinghookcanalsobeordered
withacertificate•CEmarkedinaccordancewiththeEU
machinery directive guide lines since April 2012
DEHA HD-SOCKET L IFTING SYSTEM
DEHA HA SOCKET ANCHOR SYSTEM
The DEHA Socket-anchor consists of
a steel rod and a threaded socket into
which a lifting device such as threaded
loops can be attached. HALFEN offers
a huge anchor and accessory product
range for all types of precast elements.
Quality features:•Widerangeofanchortypes• Forallformsandsizesofprecast
elements
• Loadrangesfrom0,5to12,5• Theliftinghookcanalsobeordered
withacertificate• Liftingloopavailableasaless
expensive alternative•CEmarkedinaccordancewiththeEU
machinery directive guide lines since April 2011
23© 2014 HALFEN · PG 14-E · www.halfen.com
The FRIMEDA Lifting anchor system
consists of flat steel anchors cast in
precast elements with a lifting hook, and
the ring clutch. The design of the ring
clutches and the anchors permits loads
in any direction. Ring clutches can be
released either by hand directly at the
clutch head or by remote control.
Quality features:•Loadrangefrom0,7to26,0
•Numeroustypesofanchor•Confusionofloadgroupsnotpossible•Missmatchofringclutchesand
anchors not possible, only the elementsthatbelongtogetherfit together
•Theliftinghookcanalsobeorderedwithacertificate
•CEmarkedinaccordancewiththeEUmachinery directive guide lines since April 2012
FRIMEDA TPA L IFTING ANCHOR SYSTEM
DEHA KKT L IFTING ANCHOR SYSTEM
The DEHA Lifting anchor system is cast
into the concrete together with a recess
former which will be subsequently re-
moved. The quick and easy universal
head lifting link is used to lift the con-
crete unit.
Quality features:•Safe,quick,efficient•Anchorlengthcanstillbeseenafter
installation•Clutchresistanttoabrasion•Forallformsandsizesofprecast
elements•Loadrangesfrom1,3to45,0•Theliftinghookcanalsobeordered
withacertificate•CEmarkedinaccordancewiththeEU
machinery directive guide lines since April 2012
24 © 2014 HALFEN · PG 14-E · www.halfen.com24
HALFEN Range – Framing Products
25© 2014 HALFEN · PG 14-E · www.halfen.com
Together with the corresponding
HALFEN Bolts or threaded plates,
HALFEN Framing channels offer all
the advantages of adjustable bolt
connections and framing construction.
The framing channels have application
in many areas, such as:
•Plantconstruction•MechanicalEngineering•Steelconstruction•Automotiveengineering
(locomotive/marine)•Conveyorsystems•Supplylinesintunnelling•Offshoresupplylines
Due to the flexibility of the systems,
the most cost-effective solution can be
selected for each different application.
The following channel systems are
available:
•HeavydutyHALFENFraming channels, preferably hot-rolled, esp. suitable for:
– heavy loads
– dynamic loads
– welding and steel structures
•MediumdutyHALFENFraming channels, cold-rolled
– medium loads
– with only one bolt/threaded plate
type
– compatible with the HALFEN
POWERCLICK System
•LightdutyHALFENFraming channels, cold-rolled
– light loads
– compact channel dimensions
For all systems HALFEN Framing chan-
nels are offered in unslotted or slotted
versions. Materials available are mill
finish, pre-galvanized, hot-dip galvanized
and stainless steel.
HALFEN FRAMING CHANNELS
26 © 2014 HALFEN · PG 14-E · www.halfen.com
HALFEN FRAMING SYSTEMS ACCESSORIES
HALFEN Cantilever brackets are made
from conventional HALFEN Framing
channels and offer the same advantages
of a rapid, safe and adjustable installation.
The brackets are designed for complete
support. Their high quality corrosion
protection (hot-dip galvanized or stainless
steel) remains after installation.
Advantages are:• Highloadcapacity• Easyandquicktoinstall• Compatiblewithsystem41brackets
and with the HALFEN POWERCLICK System
HALFEN Pipe clamps have been designed
for adjustable installations in pipework
construction in connection with all
HALFEN Framing channels. As with the
new HALFEN POWERCLICK System, the
material sizes of HALFEN Pipe clamps
have been designed to suit typical
requirements. Therefore, a combination
of the HALFEN POWERCLICK System
and HALFEN Pipe clamps is the most
economic solution.
Advantages are:• Widerangeofapplications
– covering a wide pipe diameter range of 15-530 mm
– axiallybracedorslidingpipefixing• Highcorrosionprotectionbygalvaniz-
ing and stainless steel• Availablewithsound/heat-insulating
rubber insulation and temperature resistant pipe support
27© 2014 HALFEN · PG 14-E · www.halfen.com
The patented HALFEN POWERCLICK
System is an innovative development for
pipe supports in industrial pipeline
construction. Never before such a high
variety of supports could be fulfilled
with so few multi-functional components,
such as for example with the System-63:
• Oneprofileforallpipesupportconstructions
• Onecornerconnectorintwodesignsfor 112 variants
•Onebeamclampforallbeamsizes
The HALFEN POWERCLICK System has
become proven technology for pipe
supports in large industrial plants. Take
advantage of its safety, efficiency and
speed at all levels!
The HALFEN POWERCLICK System is
tailored to the requirements of the
industrial pipeline construction and
enables economic system solutions.
Using the HALFEN POWERCLICK
System, support constructions are
offered with a completely new concept:
Advantages are:• Veryfewcomponents,allofthemare
multi-functional •Optimumadjustmentrange• Thelatesttechnologyatfavourable
prices• Lowweightcomparedtoconventio-
nal steel construction with constant torsionalstiffness
• Safeduetodefinedloadcapacity(comprehensively catalogued static tables)
• Onlyform-fitconnectionsare realized
•Lowstoragecosts
HALFEN POWERCLICK FRAMING SYSTEM
© 2
014
HA
LFEN
Gm
bH, G
erm
any
appl
ies
also
to
copy
ing
in e
xtra
cts.
B - 0
01 -
E - 0
4/14
5.
000
04/
14
NOTES REGARDING THIS CATALOGUETechnical and design changes reserved. The information in this publication is based on state-of-the-art technology at the time of publication. We reserve the right to make technical and design changes at any time. HALFEN GmbH shall not accept liability for the accuracy of the information in this publication or for any printing errors.
The Quality Management System of Halfen GmbH is certified for the locations in Germany, France, the Netherlands, Austria, Poland, Switzerland and the Czech Republic according to DIN EN ISO 9001:2008, Certificate No. QS-281 HH.
Furthermore HALFEN is represented with sales offices and distributors worldwide. Please contact us: www.halfen.com
Austria HALFEN Gesellschaft m.b.H.Leonard-Bernstein-Str. 101220 Wien
Phone: +43 - 1 - 259 6770 E-Mail: [email protected]: www.halfen.at
Fax: +43 - 1 - 259 - 6770 99
Belgium / Luxembourg HALFEN N.V.Borkelstraat 1312900 Schoten
Phone: +32 - 3 - 658 07 20E-Mail: [email protected]: www.halfen.be
Fax: +32 - 3 - 658 15 33
China HALFEN Construction Accessories Distribution Co.Ltd.Room 601 Tower D, Vantone CentreNo. A6 Chao Yang Men Wai StreetChaoyang District Beijing · P.R. China 100020
Phone: +86 - 10 5907 3200E-Mail: [email protected]: www.halfen.cn
Fax: +86 - 10 5907 3218
Czech Republic HALFEN s.r.o.Business Center ŠafránkovaŠafránkova 1238/1155 00 Praha 5
Phone: +420 - 311 - 690 060E-Mail: [email protected]: www.halfen-deha.cz
Fax: +420 - 235 - 314 308
France HALFEN S.A.S.18, rue Goubet75019 Paris
Phone: +33 - 1 - 445231 00E-Mail: [email protected]: www.halfen.fr
Fax: +33 - 1 - 445231 52
Germany HALFEN Vertriebsgesellschaft mbHKatzbergstrasse 3 40764 Langenfeld
Phone: +49 - 2173 - 970 - 0E-Mail: [email protected]: www.halfen.de
Fax: +49 - 2173 - 970 225
Italy HALFEN S.r.l. Soc. UnipersonaleVia F.lli Bronzetti N° 2824124 Bergamo
Phone: +39 - 035 - 0760711E-Mail: [email protected]: www.halfen.it
Fax: +39 - 035 - 0760799
Netherlands HALFEN b.v.Oostermaat 37623 CS Borne
Phone: +31 - 74-267 14 49E-Mail: [email protected]: www.halfen.nl
Fax: +31 - 74-267 26 59
Norway HALFEN ASPostboks 20804095 Stavanger
Phone: +47 - 51 82 34 00 E-Mail: [email protected]: www.halfen.no
Fax: +47 - 51 82 34 01
Poland HALFEN Sp. z o.o.Ul. Obornicka 28760-691 Poznan
Phone: +48 - 61 - 622 14 14E-Mail: [email protected]: www.halfen.pl
Fax: +48 - 61 - 622 14 15
Sweden Halfen ABVädursgatan 5412 50 Göteborg
Phone: +46 - 31 - 98 58 00E-Mail: [email protected]: www.halfen.se
Fax: +46 - 31 - 98 58 01
Switzerland HALFEN Swiss AGHertistrasse 25 8304 Wallisellen
Phone: +41 - 44 - 849 78 78E-Mail: [email protected] Internet: www.halfen.ch
Fax: +41 - 44 - 849 78 79
United Kingdom /Ireland
HALFEN Ltd.A1/A2 Portland CloseHoughton Regis LU5 5AW
Phone: +44 - 1582 - 47 03 00E-Mail: [email protected]: www.halfen.co.uk
Fax: +44 - 1582 - 47 03 04
United States of America HALFEN USA Inc.8521 FM 1976 P.O. Box 547Converse, TX 78109
Phone: +1 800.423.91 40E-Mail: [email protected]: www.halfenusa.com
Fax: +1 877.683.4910
For countries not listed HALFEN International
HALFEN International GmbHLiebigstr. 14 40764 Langenfeld / Germany
Phone: +49 - 2173 - 970 - 0 E-Mail: [email protected]: www.halfen.com
Fax: +49 - 2173 - 970 - 849
CONTACT HALFEN WORLDWIDE
HALFEN is represented by subsidiaries in the following 14 countries, please contact us: