cobra replica detail parts · shields rear fender protectors. spats gravel shields are made from...

COBRA REPLICA DETAIL PARTS

EX 17-B ~ CoBra Front BumpEr arm GrommEts$14.00 4-piece set Show Quality Bumper Arm Grommets for All Cobra Replica Cars

Help keep your bumpers from rattling while protecting your expensive paint with these EX 17-B Front Bumper Arm Grommets. These bumper arm grommets are specially fabricated using advanced rubber formulation and fabrication techniques to produce parts that will outlast and outperform any competing parts you can find. All of our dense rubber parts contain only virgin rubber, with none of the fillers

mG 6501 sEriEs ~ CoBra Door Bra anD arm rEst paint protECtor paDs

Finally, a super-easy way to prevent chips and scratches to the door ledge of your classic Cobra while improving its beauty and style! Stops damage from watches, rings, bracelets, shirt buttons, zippers and cell phones. If you have new paint, our door bras are a “must have” item! If you own an older Cobra, they’ll cover unsightly marks and scratches already present. With our peel-and-stick application, they only take a minute to install and are easily removed with a hair-dryer when needed with no damage to your paint. Available in seven colors and styles to harmonize with any paint scheme.

NOTE: MG 6501 Series Cobra Door Bras will not fit Classic Roadster replica doors. Parts to fit those cars are coming soon. MG 6501-BM Black Matte is shown.

© 2018 Metro Moulded Parts, Inc. All rights reserved.


and accelerants that cause other brands of solid rubber parts to prematurely age and fail.In addition, all our solid rubber parts include protectants added during the molding process that provide ozone and UV protection to resist these agents of decay. Further, our rubber formulations are targeted to the specific application for the intended part. These features, along with our advanced computer controls and vulcanization processes, produce long-life solid rubber parts in a class by themselves and help ensure that you get full value for the money you invest in upgrading your Cobra replica car.


Lp 60 ~ CoBra HooD & CowL sEaLLp 40 ~ CoBra trunk wEatHErstrip

Seal out water and dirt from your Cobra trunk compartment with our LP 40 Cobra Trunk Weatherstrip. This seal is made from the highest quality EPDM sponge rubber for years of reliable use. This seal is somewhat heavier than comparable seal LP 40-A and up to 30% softer than competing products. Use 3M 8008 Black Weatherstrip Adhesive to install. Sold by the foot.

mp 621-t ~ CoBra trunk LatCH paDs

Replace that cheap-looking, flat rubber factory pad with this exact-fit, show quality trunk latch pad made specifically for Cobra replica cars.

$6.00 each

Trunk latch pad placement.

Lp 40-a ~ CoBra Door wEatHErstrip

Fabricated from the highest quality dense rubber and equipped with a hug bead that surrounds the latch base, this pad both protects your paint and looks great! Made in the USA!

mp 621-C ~ CoBra HooD LatCH paDs

Finish your chrome details and protect your pricey paint job with our show-quality hood latch mounting pads. Fabricated from the highest quality dense rubber and equipped

$12.00 pair

with a hug bead that surrounds the latch base, they are designed to absorb shock – thereby reducing damage to the paint and body and keeping your car looking new longer. Sold in pairs. Made in the USA!

Hood latch mounting pad placement.

Lp 54-a ~ CoBra smaLL HooD sEaL

$4.00 per foot

Help keep dust, dirt, sand, grit and water from the interior of your cherished Cobra with our LP 40-A Cobra Door Weatherstrip. Somewhat heavier than compar-able seal LP 40-A and up to 30% softer than competing products. Use 3M 8008 Black Weatherstrip Adhesive to install. Sold by the foot.

LP 60 Cobra Hood & Cowl Seal is somewhat larger and heavier than LP 54-A Small Hood Seal and is an ideal choice for the cowl seal on your Cobra. It is made from the same top quality EPDM sponge rubber and we guarantee it against chemical breakdown for 15 years. Use 3M 8008 Black Weatherstrip Adhesive to install. Sold by the foot.

Keep your Cobra engine looking clean and bright and reduce vibration and wind rattle with our LP 54-A Cobra Small Hood Seal. Unlike cheap foam seals, EPDM sponge rubber will not degrade when exposed to pollutants like engine exhaust and petroleum gases – giving you years of reliable service. Use 3M 8008 Black Weatherstrip Adhesive to install. Sold by the foot.

$4.00 per foot

2.www.metrommp.com 800-878-2237

$4.00 per foot

$1.90 per foot

Lp 63-C ~ Door & trunk siDE sEaL

Our LP 63-C Cobra Door & Trunk Side Seal is an excellent choice for sealing your door or trunk. Made from the same top quality EPDM sponge rubber as our other seals, we guarantee it against chemical breakdown for 15 years. Use 3M 8008 Black Weatherstrip Adhesive to install. Sold by the foot.

$4.60 per foot

GL 11 ~ 3m 8008 BLaCk wEatHErstrip aDHEsivE

A strong, flexible, rubbery adhesive that can withstand vibration and extreme temperature variations. It can be used to bond automotive weatherstripping and is a great adhesive for holding paper, cork, or rubber gaskets in place during installation. 5 oz. tube.

$16.65 tube

• Fast drying, strong, flexible, rubbery adhesive with good oil and water resistance

• Withstands vibration & extreme temperature variation

• Black color designed to match vehicle weatherstrip for virtually invisible repair

• Can be used to bond weatherstripping to car doors, trunks, T-tops, moon roofs and sun roofs


$20.25 pair

mp 621-BC ~ CoBra winDsHiELD BasE trim paDs

Protect your paint and detail-out your Cobra like a professional with our MP 621-BC Cobra Wind-shield Base Trim Pads. These dense rubber pads

Hr 17 ~ CoBra HEaDLiGHt trim rinG sEaLs

Specially created for Cobra replica cars, our HR 17 Cobra Headlight Trim Ring Seals are made to replace poor quality originals. Designed with a molded-in hug

$46.55 pair

Headlight ring-seal hug bead.

Windshield base trim pad with show bead.

$16.80 3-piece set

mp 621-Ct ~ CoBra HooD LatCH & trunk LatCH mountinG paDs sEt

Save money by replacing all your Cobra hood and trunk latch pads at the same time! Our MP 621-CT Hood and Trunk Latch Pad Set includes one pair of our popular MP 621-C Hood Latch Pads and one each of our MP 621-T Trunk Latch Pad. 3-piece kit. Made in the USA!

Fm 6500 ~ CoBra BaCkDraFt FLoor mats

All rubber, show-quality floor mats give your Cobra a look of distinction unlike anything else. Molded in one piece from the highest quality tooling, our FM 6500 Cobra Backdraft Floor Mats are made to sew or glue directly

$125.00 pairCOMING SOON!

3. www.metrommp.com800-878-2237

were made with a show bead by request specifically for Shelby Cobra replica cars. Use with metal trim top plates (available from others) for a real touch of class! Sold in pairs. Made in the USA!

into the rug. Fits Backdraft Cobra only. Contact Metro Moulded Parts, Inc. if you want specialty floor mats fabricated for your make/model of Cobra! Sold in pairs. Made in the USA!

bead, these seals both fill the gap between the trim rings and body and hug the trim ring outer circumference to provide a superior functional seal with show-quality looks. Sold in pairs. Made in the USA!

mG 6502 sEriEs ~ GravEL sHiELDs (spats)

Keep your paint looking good as new and dramatically transform the look of your Cobra replica car with Spats gravel shields rear fender protectors. Spats gravel shields are made from the toughest vinyl available and laminated for added protection. They are die-cut with adhesive-backing and top laminated for long life and a paint-quality appearance. They

Cobra Spats Gravel Shields placement. MG 6502-BM shown.

MG 6502-CL Clear / Invisible $34.99 MG 6502-BM Black Matte $34.99 MG 6502-W White $34.99MG 6502-C Chrome $39.99 MG 6502-MS Metallic Silver $39.99 MG 6502-CF Carbon Fiber $69.99

are easily installed (just peel-off and press on) and safe for all finishes. The perfect way to protect and customize your Cobra rear fender! Sold in pairs. Made in the USA!



MG 6851-B/RS Black Letters on SilverMG 6851-R/RS Red Letters on SilverMG 6851-R/W Red Letters on WhiteMG 6851-RS/B Silver Letters on BlackMG 6851-W/B White Letters on BlackMG 6851-W/RMB White Letters on Metallic BlueMG 6851-W/R White Letters on Red MG 6851-RG/B Metallic Gold Letters on BlackMG 6851-Y/B Yellow Letters on Black

$12.99 per set

mG 6851 sEriEs ~ DasH knoB LaBEL sEts

mG 6850 ‘Caution Hot EXHaust’ warninG DECaLs

Help keep passengers and on-lookers safe from burns with our body color show-thru decals. Lettering is 0.71 in. high x 10.25 in. long and made from tough, tear-resistant vinyl. They can be removed easily without damaging the paint below. Sold in pairs, one for each side of your Cobra replica car or other vehicle. Metallic-silver letters on clear film. Note: Red background body paint is shown in the image at left.

$24.50 per pair

Here’s an easy way to make your AC Cobra and other sports cars stand out from the crowd! Our MG 6851 Series Dash Knob Label Sets can be used to detail-out AC Cobra’s, street rods, muscle cars, sports cars and race cars. These are the highest quality, adhesive-backed peel-and-stick labels available anywhere. Laminated for long-life and die-cut for easy application, just lift and place over the plastic barrel- or billet-knobs on your car for an amazing new look. Available in nine (9) styles, each label is 5/8 in. (15.88 mm) in diameter. Each label set includes nine (9) round labels for barrel knobs and three (3) rectangular labels for aircraft-style toggle switch covers on a sheet. These work great with our KN 65 Cobra Dash Console Knobs!

Make your Cobra stand out from the crowd with our KN 65 Cobra Dash Console Knob! These are all-metal dash knobs with a bright chrome finish that replace your current dash knobs to provide beautiful custom

$11.45 each

kn 65 ~ CoBra DasH ConsoLE knoB

$28.50 pair

mG 6500-B, -C ~ winD-winG & sunvisor trim kit

Now you can create a finished look for your bare-edged Plexiglas® wind-wings and sunvisors with this simple-to-install trim kit. Fits all AC Cobras. Available in black matte black finish (MG 6500-B) or bright chrome finish (MG 6500-C). One kit completes the entire car. Installation instructions included.

Example decal placement.

detail to your cobra’s interior, as well as long-lasting good looks. Each knob sold separately. Use with MG 6501 Series Dash Knob Label Sets shown above.

Console knob placement.



Add style to your Cobra with our new MG 6800 Series “Powered By” Hood Scoop Decals. Decals are 1 in. tall x 12.9 in. wide and made from tear-resistant, tough automotive vinyl. They can be removed easily without damaging the paint beneath using a hair dryer. Choose from five (5) different colors. Provided in pairs, one for each side of your Cobra or other vehicle. Includes application instructions.

$28.50 per pairmG 6800 sEriEs ~ HooD sCoop DECaLs

MG 6800-W White Gloss MG 6800-B Black Gloss MG 6800-BM Black Matte MG 6800-BA Brushed Aluminum MG 6800-MS Metallic Silver









Refer to the following pages for ordering information for our door, hood and trunk racing meatballs in various sizes and font styles. They are available in both static cling or paint-quality laminated vinyl. Choose from four (4) different font styles and as many as four (4) different diameters. These numbered meatball graphics look great with the double-stripe kit for your classic AC Cobra.

Note: Font styles and stock numbers are shown opposite and in the Font Styles table on page 10.

Cobra Printed Vinyl Racing Meatballs

Door Meatballs Hood & Trunk Meatballs Type

10 in. Roundel 11 in. Roundel 11 in. Roundel 16 in. Roundel 18 in. Roundel Size$70.50/pr. $77.50/pr. $31.25/ea. $38.50/ea. $39.25/ea. Price / Description

MG 6510-W/A MG 6511-W/A MG 6611-W/A MG 6616-W/A MG 6618-W/A White background / Black #’s ~ FONT AMG 6510-W/B MG 6511-W/B MG 6611-W/B MG 6616-W/B MG 6618-W/B White background / Black #’s ~ FONT BMG 6510-W/C MG 6511-W/C MG 6611-W/C MG 6616-W/C MG 6618-W/C White background / Black #’s ~ FONT CMG 6510-W/D MG 6511-W/D MG 6611-W/D MG 6616-W/D MG 6618-W/D White background / Black #’s ~ FONT D

MG 6510-MS/A MG 6511-MS/A MG 6611-MS/A MG 6616-MS/A MG 6618-MS/A Metallic Silver background / White #’s ~ FONT AMG 6510-MS/B MG 6511-MS/B MG 6611-MS/B MG 6616-MS/B MG 6618-MS/B Metallic Silver background / White #’s ~ FONT BMG 6510-MS/C MG 6511-MS/C MG 6611-MS/C MG 6616-MS/C MG 6618-MS/C Metallic Silver background / White #’s ~ FONT CMG 6510-MS/D MG 6511-MS/D MG 6611-MS/D MG 6616-MS/D MG 6618-MS/D Metallic Silver background / White #’s ~ FONT D

MG 6510-B/A MG 6511-B/A MG 6611-B/A MG 6616-B/A MG 6618-B/A Black background / White #’s ~ FONT AMG 6510-B/B MG 6511-B/B MG 6611-B/B MG 6616-B/B MG 6618-B/B Black background / White #’s ~ FONT BMG 6510-B/C MG 6511-B/C MG 6611-B/C MG 6616-B/C MG 6618-B/C Black background / White #’s ~ FONT CMG 6510-B/D MG 6511-B/D MG 6611-B/D MG 6616-B/D MG 6618-B/D Black background / White #’s ~ FONT D

MG 6510-BM/A MG 6511-BM/A MG 6611-BM/A MG 6616-BM/A MG 6618-BM/A Matte Black background / White #’s ~ FONT AMG 6510-BM/B MG 6511-BM/B MG 6611-BM/B MG 6616-BM/B MG 6618-BM/B Matte Black background / White #’s ~ FONT BMG 6510-BM/C MG 6511-BM/C MG 6611-BM/C MG 6616-BM/C MG 6618-BM/C Matte Black background / White #’s ~ FONT CMG 6510-BM/D MG 6511-BM/D MG 6611-BM/D MG 6616-BM/D MG 6618-BM/D Matte Black background / White #’s ~ FONT D

MG 6510-R/A MG 6511-R/A MG 6611-R/A MG 6616-R/A MG 6618-R/A Red background / White #’s ~ FONT AMG 6510-R/B MG 6511-R/B MG 6611-R/B MG 6616-R/B MG 6618-R/B Red background / White #’s ~ FONT BMG 6510-R/C MG 6511-R/C MG 6611-R/C MG 6616-R/C MG 6618-R/C Red background / White #’s ~ FONT CMG 6510-R/D MG 6511-R/D MG 6611-R/D MG 6616-R/D MG 6618-R/D Red background / White #’s ~ FONT D

MG 6510-Y/A MG 6511-Y/A MG 6611-Y/A MG 6616-Y/A MG 6618-Y/A Yellow background / Black #’s ~ FONT AMG 6510-Y/B MG 6511-Y/B MG 6611-Y/B MG 6616-Y/B MG 6618-Y/B Yellow background / Black #’s ~ FONT BMG 6510-Y/C MG 6511-Y/C MG 6611-Y/C MG 6616-Y/C MG 6618-Y/C Yellow background / Black #’s ~ FONT CMG 6510-Y/D MG 6511-Y/D MG 6611-Y/D MG 6616-Y/D MG 6618-Y/D Yellow background / Black #’s ~ FONT D

MG 6510-GM/A MG 6511-GM/A MG 6611-GM/A MG 6616-GM/A MG 6618-GM/A Gold Metallic background / White #’s ~ FONT AMG 6510-GM/B MG 6511-GM/B MG 6611-GM/B MG 6616-GM/B MG 6618-GM/B Gold Metallic background / White #’s ~ FONT BMG 6510-GM/C MG 6511-GM/C MG 6611-GM/C MG 6616-GM/C MG 6618-GM/C Gold Metallic background / White #’s ~ FONT CMG 6510-GM/D MG 6511-GM/D MG 6611-GM/D MG 6616-GM/D MG 6618-GM/D Gold Metallic background / White #’s ~ FONT D

MG 6510-SC/A MG 6511-SC/A MG 6611-SC/A MG 6616-SC/A MG 6618-SC/A Static Cling White background / Black #’s ~ FONT AMG 6510-SC/B MG 6511-SC/B MG 6611-SC/B MG 6616-SC/B MG 6618-SC/B Static Cling White background / Black #’s ~ FONT BMG 6510-SC/C MG 6511-SC/C MG 6611-SC/C MG 6616-SC/C MG 6618-SC/C Static Cling White background / Black #’s ~ FONT CMG 6510-SC/D MG 6511-SC/D MG 6611-SC/D MG 6616-SC/D MG 6618-SC/D Static Cling White background / Black #’s ~ FONT D


The following table provides ordering information for our blank racing meatballs. They are available in both static cling or paint-quality laminated vinyl. Choose from four (4) different font styles and seven (7) different colors. You can paint numbers directly onto the roundels, or use our printed vinyl number sets available in black or white.

Cobra Blank Printed Vinyl Racing Meatballs

Blank Door Meatballs Blank Racing Meatballs Type

10 in. Roundel 11 in. Roundel 16 in. Roundel 18 in. Roundel Size$32.50/pr. $41.50/pr. $57.00/pr. $59.50/pr. Price / Description

MG 6710-B MG 6711-B MG 6716-B MG 6718-B Black RoundelMG 6710-BM MG 6711-BM MG 6716-BM MG 6718-BM Matte Black RoundelMG 6710-GM MG 6711-GM MG 6716-GM MG 6718-GM Gold Metallic RoundelMG 6710-MS MG 6711-MS MG 6716-MS MG 6718-MS Metallic Silver RondelMG 6710-R MG 6711-R MG 6716-R MG 6718-R Red RoundelMG 6710-SC MG 6711-SC MG 6716-SC MG 6718-SC Static Cling White RoundelMG 6710-W MG 6711-W MG 6716-W MG 6718-W White RoundelMG 6710-Y MG 6711-Y MG 6716-Y MG 6718-Y Yellow Roundel



Cobra Printed Vinyl Custom Number Sets

Custom Number Sets Type

6 in. high 6.5 in. high 9.5 in. high 11 in. high Size$12.00/pr. $12.00/pr. $15.00/pr. $16.00/pr. Price / Description

MG 6753-B MG 6752-B MG 6751-B MG 6750-B Black RoundelMG 6753-BM MG 6752-BM MG 6751-BM MG 6750-BM Matte Black RoundelMG 6753-GM MG 6752-GM MG 6751-GM MG 6750-GM Gold Metallic RoundelMG 6753-MS MG 6752-MS MG 6751-MS MG 6750-MS Metallic Silver RondelMG 6753-R MG 6752-R MG 6751-R MG 6750-R Red RoundelMG 6753-W MG 6752-W MG 6751-W MG 6750-W White RoundelMG 6753-Y MG 6752-Y MG 6751-Y MG 6750-Y Yellow Roundel

The following table provides ordering information for our custom number sets for use with blank racing meatballs. These customizable number sets are made from high quality, removable vinyl, allowing you to change your racing numbers whenever you like. Choose from any of the four Font Styles A - D shown below.



Metro Moulded Parts, Inc.11610 Jay St. NW • Minneapolis, MN 55448 • Toll-free: 800-878-2237

www.metrommp.com

NONSTK 76 – REV. 14

cobra replica detail parts · shields rear fender protectors. spats gravel shields are made from...

Documents