IMEXTM Veterinary, Inc.1001 McKesson DriveLongview, Texas 75604800-828-4639www.imexvet.com

FIRST CLASSU.S. POSTAGE

PAIDLONGVIEW, TXPERMIT NO. 9

50% OFFon the purchase of a single resin cartridgeBe one of the first one hundred customers to purchase an applicator gun and receive 50% off a single resin cartridge.

FIRST100ORDERS

Veterinary External Fixation AcrylicAcryl ™

Clean & EasyAcrylic Fixator SystemIdeal for avian, exotics, feline, toy breeds and mandibular fractures

Acrylx™ ( e kril ex ) is a methacrylate based composite resin designed to simplify construction of pin

and acrylic external fixators on toy breeds, avian, feline, exotics and mandibular fractures. Unlike

other commonly used products, Acrylx™ has minimal odor and does not require pre-mixing before

application. Acrylx™ is near-radiolucent while providing abrasion resistance and high strength.

Two resin components are supplied in a single divided cartridge and applied using a custom mixing

gun. The resin components are blended as they pass through disposable mixing tips for a clean and

quick delivery.

Clean & Easy...No Mess, Minimal Odor

Avian | Exotic | Feline | Toy Breeds

• Near-radiolucency produces unobstructed

radiographic films for a clear view of the

fracture site

• Multi-use resin cartridge provides potential

to amortize cost across patients

Veterinary External Fixation AcrylicAcryl ™

Long-eared Owl Teaching Case

A single cartridge provides 50ml of mixed product – enough material to

construct several small patient frames. Maximum shelf-life is maintained by

refrigerated storage but not required. If refrigerated, it is recommended to

allow the cartridge to reach room temperature before use as not to alter

setting characteristics. An 8-12 minute set time is typical. Each cartridge

purchase includes five yellow and five pink mixing tips.

The custom applicator gun readily accepts the divided Acrylx™ cartridge, is

easy to control, durable and should last many years under normal use.

Applicator Gun PN 70011

Applicator Gun & Resin Cartridge

Resin Cartridge PN 70012

Avian Pectoral Limb Repair

Mixing tips are available in a variety of sizes and can be ordered individually.

Mixing Tips

PN 70013 Acrylx™ Mixing Tips, Fine (Blue)

PN 70014 Acrylx™ Mixing Tips, Medium (Yellow)

PN 70015 Acrylx™ Mixing Tips, Large (Pink)

PN 70016 Acrylx™ Mixing Tips, Extra Large (Blue-Green)

Five yellow and five pink tips are included with each cartridge purchase.

Accessory packs include a variety of all mixing tips (three of each size) and

tube sizes (five 300mm sections of 6mm and 10mm diameter) as well as

10mm adapter plugs. This pack is designed to provide all options with the

initial purchase of an applicator gun and cartridge. All items in the kit are

available individually for future orders or specific needs.

Accessory Pack PN 70080

Mixing Tips & Accessory Pack

Acrylx™ is most commonly applied using thin-wall tubing as a mold. Two

tube diameters are available for use with small patients: 6mm and 10mm.

6mm tubing is easily filled directly using medium, large, or extra large mixing

tips. 10mm tubing utilizes an adapter plug which fits the mixing tip for a

clean and smooth fill. Large or extra large mixing tips are commonly used

with 10mm tubing.

Corrugated Tubing & Plugs

PN 70020 Acrylx™ Corrugated Tubing, 6mm x 300mm

PN 70050 Acrylx™ Corrugated Tubing, 10mm x 300mm

PN 70060 Acrylx™ 10mm Adapter Plug

PN 70060R Acrylx™ 10mm Solid Plug

Rabbit Midshaft Tibial Fx Repair

800-828-4639www.imexvet.com

AcrylxVeterinary, Inc.

Instructions | Quick and Simple Setup Push up the release lever at the rear of the gun and pull the plunger as far back as it will go.

Flip the cartridge lock into an up position and seat the cartridge in the gun. The notch in the base of the cartridge should face downward.

Close the cartridge lock by pushing downward.

Before affixing the mixing tip, remove the cap that seals the cartridge by twisting the cap counterclockwise and pulling it from the cartridge. Discard the cap.

Express approximately 1/4” of material directly from the cartridge onto a pad to ensure both components are flowing properly.

Affix the mixing tip by aligning the small triangle on the colored base of the tip with the corresponding notch in the cartridge. Seat the tip fully and lock in place by rotating the tip’s colored base clockwise. Apply Acrylx as desired.

When application is complete, leave the used tip in place to protect unused portions of resin residing in the cartridge. At next use, replace with a new tip and begin process at step 4.

To remove the cartridge, push up the release lever and pull the black plunger as far back as it will go. Open the cartridge lock to release the cartridge.

IMPORTANT: Never use excessive force when expressing material. Doing so may damage the gun, rupture the cartridge or cause the rear of the cartridge to leak. If the material does not flow easily, remove the tip and use a wire or needle to remove any set material clogging the cartridge orifices. Attach new tip.

NOTE: This cartridge gun is designed for 1:1 ratio, split cartridges. The cartridges feature a gap between the two barrels.

800-828-4639www.imexvet.com

AcrylxVeterinary, Inc.

1

800-828-4639www.imexvet.com

AcrylxVeterinary, Inc.

2

3

4

800-828-4639www.imexvet.com

AcrylxVeterinary, Inc.5

800-828-4639www.imexvet.com

AcrylxVeterinary, Inc.

6

Quick & Simple Setup