39'x19' Chicken Run Plan

Designed for up to 55 chickens

DisclaimerThe information provided here will show you how to build a chicken coop. However, we at howtoplans.org do not claim that the recommended techniques are the only way to accomplish this task. It will be the responsibility of each customer to ensure the application of the correct construction methods and the use of the proper materials.In addition to the selection of the materials, the customer will be responsible for such construction issues as caulking, flashing, gluing, insulating and nailing, for ensuring adequate workmanship in the areas of installation, roofing and weatherproofing, and for any other items that are beyond the control of the designer. The materials mentioned in the plans do not represent an endorsement or recommendation of any particular product.

The Responsibility of UsersDespite our commitment to presenting accurate information, howtoplans.org is not liable for any errors or omissions appearing in the plans. Furthermore, howtoplans.org will not be liable for any consequential, special, incidental or indirect damages resulting from the use of this information. Our freedom from liability also extends to such issues as the loss of anticipated profits or business opportunities, and economic losses stemming from the use of howtoplans.org, regardless of whether there has been notification of such damage.

LiabilityThose who utilize the methods described on howtoplans.org will be responsible for their own actions. We are not liable for any injuries or property damage that may arise from the use of the information appearing on this website. If you decide to use these plans, you should employ only quality materials and should always adhere to good safety practices. In the event that you are unable to complete the project on your own, you should contact a certified contractor to ensure that construction is completed with the highest standards.

PermissionsIt is important to understand that planning and permission issues are dependent upon local requirements. Users of these plans are responsible for complying with the appropriate statutes and regulations, and for the proper implementation of the plans or other construction information provided by howtoplans.org. The city or county office in your area should be able to provide you with the relevant information.

Copyright The text and illustrations that appear here are the exclusive property of howtoplans.org and are protected by federal copyright laws. The duplication, sale or distribution of any portion of these plans without prior written consent from the original designer will be subject to the appropriate penalties for copyright infringement. Sharing this plan on the web is only permited with an indicated original source: https://www.howtoplans.org

Assemble the bottom frame

Assemble the frame from the beams with cross-section 4 x 4 inch.

At the junction, make a sample of half the thickness of the beam and a depth of 4 inches

Connect the beams with 4x 3 1/2" self-tapping screws for each joint

Clarify that all diagonals are equal

A

12' 8' 8"

12'

8' 3 1/2"

19' 11 1/2"

8' 3 1/2"

12'5' 10" 8' 8"

12'8' 11 1/2"

5' 10"

3' 8"

3' 8"

3' 8"

3' 8"

3' 11 3/4"

3' 11 3/4"

7'

3' 8"

Framing the coop's walls

Install the support pillars of the 7 ft beam with a cross-section of 4 x 4 inches according to the drawing

Secure the support pillars to the bottom of the frame by means of mounting brackets and screws

4' 8"

4' 9"

4' 9"

4' 8" 5' 2"

8' 7 1/2"

5' 2"

Assemble the aviary's roof frame

Assemble the frame from the beams with cross-section 2 x 4 inch.

In the intersection of longitudinal and transverse beams, cut in half the thickness of the beam according to the drawings and connect the beams with 3 1/2'"' self-tapping screws for each joint

The ends of the beams are fixed with the help of hangers on the main frame and 7x 3 1/2" self-tapping screws

J J

K

7'-6

"

2'-

11"

7' 6"

2' 11"2' 11"4" 4"

4"

45° 45°

2x 6" self-tapping screws for each joint

Middle support assemble and installationProvide the middle support main pillar from the beam with the cross-section 2x4 inch

Provide side struts from the beam with the cross section 2x4 inch. Cut the ends of the beams at 45 degrees. Attach the struts to the main beam with two mounting corners 8x8x1 1/2 inch and 7x2" self-tapping screws

Install the lower part of the support in post base and fix it with 8x 2" self-tapping screws

Combine the upper part with the transversal ceiling beam and fixed with self-tapping screws

1' 9" 1' 1

0" 1' 10" 1'

10" 1' 10" 1

' 10" 1' 10"

1' 10" 1

' 10"

1' 9"

Assemble and installation of roof rafters

Assemble the 11 rafters of the beams with a cross-section of 4 x 2 inches: cut the beams ends according to the drawing. Connect them with mounting plates and 2" self-tapping screws.

Fasten the outer rafters with twist strups to the top frame, other rafters - with ties. Use for this 2" self-tapping screws.

4'-3

"4

1/2" 5' 3/4"

Front siding shields installation

Prepare the 7 1/8 inch wide siding board for front wall sheathing in the required amount according to the drawing. Assemble siding shields with 2" galvanized nails to the frame beams

Prepare wire mesh according to the dimensions

Prepare window's jambs from the beam with a cross-section of 3 x 1/2 inches. Cut the ends by 45 degrees for connecting them into the frames

Put the mesh on the window openers, fix it in corners. Install window jambs by window's opener perimeter. The edge of the grid must be completely closed.

4' 5 3/4" 2' 6 1/2"

2' 6"

1' 8

"

1' 4

" 1' 4

"

4' 5 3/4"

1' 6 3/4"

2' 4"

1' 3 1 /4"

4' 5 3/4" 2' 5 3/4"

Front hatching eggs case assemble

Assemble the frame of a beams with a cross section of 2 x 2 inches, according to the drawing. The upper plane has a slope of 8 degrees. Prepare the slits for the partitions in the longitudinal beams

Cover the frame with 1/2 plywood from all sides except back and top with help of 2 1/2" self-tapping screws

Coop's door assembly and installation

Assemble the frame from the beams with cross section 2x3" and 2x2" with 4" self-tapping screws according to the drawing

Prepare the 7 1/8 inch wide siding board for door sheathing in the required amount according to the drawing. Assemble siding shields with 2" galvanized nails to the frame beams

Install door jambs from the beams with cross section 3x1/2" according to the drawing

Install the door assembly to the wall with the help of two hinges on the left side. Put the handle on the right side

4' 7"

4' 7"

4' 7"

4' 7"

4' 7" 4' 7"

4' 7" 4' 7"

19' 11 1/2"

19' 11 1/2"

3'8"

3' 8"

1' 3"

5' 2"

7'

Aviary's wire mesh installation

Prepare wire mesh sheets according to the drawing. To cover all the square will need 110 m2 of wire mesh

Fasten the mesh with an industrial stapler

3' 8"

Final touches

Don't forget to choose the desirable paint for your mood and the colors of your yard. Decorate your chicken coop by giving it unique and stylish look.

Copyright

The text and illustrations that appear here are the exclusive property of howtoplans.org and are protected by federal copyright laws. The duplication, sale or distribution of any portion of these plans without prior written consent from the original designer will be subject to the appropriate penalties for copyright infringement. Sharing this plan on the web is only permited with an indicated original source: https://www.howtoplans.org

This free plan was brought to you by:

For more great HOW-TO plans please visit: www.howtoplans.org