bx600

PRIMERGY BX600 System UnitsSystem configurator and order-information guide

Contents

InstructionsConfiguration diagramConfigurator

I 1 BX600 System UnitsII 2 BX600 Server Blades IV 4 Communikation/Network 1VII 7 Communikation/Network 2

Change report

PRIMERGY Server

January 2009

System configurator and order-information guidePRIMERGY BX600 System Units Status: 2008-12-17

InstructionsThis document contains basic product and configuration information that will enable you to configure your system viaSystem-Architect.

Only the tool "System-Arcitect" will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system.

Please pay attention to the naming conventions: BX600 S2 System unit 2nd generationBX600 S3 System unit 3rd generation

You can configure your individual PRIMERGY server in order to adjust your specific requirements.

The System configurator is divided into several chapters that are identical to the current price list and PC-/ System-Architect.

Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom.

Section IV Memory, example

There are 3 free memory banks available.The memory banks can be populated with 512MB, 1GB, 2GB and 4GB DDR Memory.The maximum total amount of memory is 12GB.It is possible to select memory upgrade options up to 3 times.ECC with memory scrubbing-function and hot-spare memorybank is standard on the PRIMERGY BX600 S3 Server Blades.

S26361-XXX-XXX S26361-XXX-XXXMemory XXX MB Memory XXX MB

X times

max. X times per system max. X times per system

In one chapter you can only select as many components (here 3x) as the arrow indicates. 3x

Please note that there are information symbols which indicate necessary information.

For further information see:

http://www.fujitsu-siemens.com/primergy (internet)

http://extranet.fujitsu-siemens.com/primergy (extranet)

Prices and availability see price list and PC-/ System-ArchitectSubject to change and errors excepted

Fujitsu Siemens ComputersEnterprise Products - PRIMERGY Server 2 of 11

http://www.fujitsu-siemens.com/primergy

http://extranet.fujitsu-siemens.com/primergy


Configuration diagram BX600 S3 System Unit

System Unit ( I )

NET1 NET3

Slot 1: Server Blade










NET2 NET4

Key:

Included in basic unit Option

Server Blade Mix and Compatibility Matrix for BX600 S3 System Unit

BX600 S3 BX620 S3 BX620 S4 BX630 BX630 S2BX620 S3 x x x xBX620 S4 x x x xBX630 S2 Dual x x x xBX630 S2 Quad x x x x

Switch, IBP and Pass-Thru Blades released for BX600 S3 System Units EOL (Status 65)

BX600 S2/S3 Downlink ports Uplink ports Order number installable in1GbE Pass-Thru 10x 1Gbit 10x 1Gbit RJ45 S26361-F3112-E1 NET1/2/3/41GbE Switch 10x 1Gbit 6x 1Gbit RJ45 S26361-F3206-E6 NET1/2/3/41/10GbE Switch 10x 1Gbit 6x 1Gbit RJ45, 2x 10Gbit XFP S26361-F3206-E8 NET1/2/3/41GbE Switch Cisco 10x 1Gbit 2x 1Gbit RJ45, 4x 1Gbit SFP S26361-K1234-V200 NET1/2/3/41GbE IBP 10/6 10x 1Gbit 6x 1Gbit RJ45 S26361-F3860-E1 NET1/2/3/41GbE Switch 30/12 30x 1Gbit 12x 1Gbit RJ45 S26361-F3467-E1 NET1/2/3/41GbE IBP 30/12 30x 1Gbit 12x 1Gbit RJ45 S26361-F3859-E1 NET1/2/3/410GbE Switch 10x 1Gbit 2x 10Gbit X2 S26361-F3309-E1 NET3/42Gb FC Pass-Thru 10x 2Gbit 10x 2Gbit SFP S26361-F3024-E1 NET3/42/4Gb FC Switch 10x 2Gbit 6x 4Gbit SFP S26361-F3144-E6 NET3/42/4Gb FC Switch 10x 2Gbit 4x 4Gbit SFP S26361-F3144-E4 NET3/44Gb FC Pass-Thru 10x 4Gbit 10x 4Gbit SFP S26361-F3024-E10 NET3/44/4Gb FC Switch 10x 4Gbit 6x 4Gbit SFP S26361-F3144-E16 NET3/44/4Gb FC Switch 10x 4Gbit 4x 4Gbit SFP S26361-F3144-E14 NET3/4

Extension slots rear sideExtension slots front side

Rea

r

Fro

nt

Mid

pla

ne

wit

h c

on

nec

tors G

bE

Sw

itch

, IB

P

or

Pas

s-T

hru

FC

or

Gb

E

Pas

s-T

hru

/Sw

itch

FC

or

Gb

E

Pas

s-T

hru

/Sw

itch

KV

MM

MB

PS

U 3

PS

U 1

PS

U 2

PS

U 4

Gb

E S

wit

ch, I

BP

o

r P

ass-

Th

ru

Fan

un

it

Fan

un

itM

MB


System configurator and order-information guideA PRIMERGY BX600 System Units Status: 2008-12-17

Section I System Units BX600 S3

The System Units BX600 S3 consists of:* 7U chassis including * Rack mounting kit suitable for

- PRIMERGY 19" PRIMECENTER Rack, FJ new rack and 3rd party racks (e.g. Rittal) - 1 pair of carrier rails and 1 bracket for DC-Rack

* 2 hot-plug power supplies 2100W at 230V * 2 power cords 16A IEC320 C19 -> 16A IEC320 C20, 3.5m length* All redundant hot-plug fans at the rear side

- 2 fan modules each with 2 fans (2+2 redundancy) and 3 fans in every power supply* Drives / bays / slots

- 10 empty slots for 10 hot-plug dual, or 5 quad, or 2 octal Server Blades at front side. - 4 empty slots for up to 4x Gbit Ethernet Switch or Pass-Thru Blades at rear side - 2 empty slots for two Fibre Channel Switch or Pass-Thru Blades at rear side - 2 empty slots for additional hot-plug power supplies at rear side

* 2 redundant hot-plug Management BladesExternal Interfaces: - 1x RS-232-C (serial, 9 pin) per Management Blade (2 total) - 1x LAN RJ45 per Management Blade (2 total) - 1x keyboard (PS/2), 1x mouse (PS/2), 1x VGA (15pin) on the KVM switch, via special cable - 1x VGA and 2x USB 1.1 at front side of each Server Blade via special cable For external interfaces of the different Switch and Pass-Thru Blades see sections II and V.

Cables (shipped with each System Unit): - 1x special cable with 2x USB for external CD/FD and 1x VGA for Server Blade front side connection. - 1x special cable with 2x PS/2 and 1x VGA for KVM switch Software: - ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates

Dual, 4-way and the 8-way Server Blades can be used in mixed configuration within one system unit.Note: Server Blades can also be ordered for further extention later! But at least one Server Blade must be integrated in the System Unit ex works.

S26361-K1156-V302BX600 S3 System Unitfor 19" Racks, with 2x Management Blade S32x PSU with power cordsNeeds 7 height units (U)

The System Unit includes 2 PSUs and 2 power cords!

(S26361-F3151-E300: 16A IEC320 C19 -> 16A IEC320 C20 )Different power cords can be optional ordered as L-Numbers.(S26361-F3151-L100 or-L200 or -L300 or -L500).The included power cords can be used for the socket strips S26361-F2262-E132 (1x3 16A IEC320) or S26361-F2262-E332 (3x3 16A IEC320) and to different PRIMERGY UPS systems.Note: UPS must provide at least one 16A IEC320 C20 socket and it must support min. 2100W.For further details, see PRIMERGY UPS configurator sheets. For connections out of the rack, there are 3 power cords available (S26361-F3151-L100 or-L200 or -L500).

S26113-F603-E1 The additional PSU is shipped inclusive a power cord!Hot plug (S26361-F3151-E300: 16A IEC320 C19 -> 16A IEC320 C20 )

2x power supply module (PSU) It is the same power cord as for the PSUs shipped with the system unit.for redundancy (2100W) Different power cords can be optional ordered as L-Numbers.inclusive power cord (S26361-F3151-L100 or-L200 or -L300 or -L500).max. 2x per system unit

Overview of Power Supply (PSU) redundancy

Number Max. number of dual / 4-way Max. number of dual / 4-way

of server blades, server blades,

PSU with PSU redundance without PSU redundance

2 redundancy can not be defined 10* / 5* = no redundancyS26361-F3888-L1 3 10* / 5* = 2+1 redundancy 10 / 5 = no redundancyUpgrade Kit for BX600 S3 4 10* / 5* = 2+2 redundancy 10 / 5 = no redundancywith MMB S2 (-V301/-V303). 4 10 / 5 = 3+1 redundancy 10 / 5 = no redundancyTo replace MMB S2 by MMB S3. *) depending on server blade configurationContains 2x MMB S3 plus FCBmax. 1x per system unit

B


System configurator and order-information guideB PRIMERGY BX600 System Units Status: 2008-12-17

The Standard KVM Module or the Adv. respectively dKVM Switch must be ordered with System Unit!

S26361-F3113-E2 S26361-F3113-E102Standard KVM Module Digital KVM Switch Blade (dKVM)Keyboard/Video/Mouse Switch KVM over IP Switch, Virtual Media

1x Special cable with 2x PS/2, 1x VGA Graphical Console Re-direction over IPis part of the System Unit delivery. Special cable with 2x PS/2, 1x VGA max. 1x per System Unit is part of the System Unit delivery.

max. 1x per System Unit

PRIMERGY Rack S26361-K1156-V304System Unit for 19'' racks with

PRIMERGY PRIMECENTER-Rack 2 Management Blades (MMB S3),2x Dummy Server Blades and 2x power supply module.Orderable without Server Blades, without upgrade possibility ex works (fixed configuration).Expansions are possible with loose deliveries of the correspondently released components!

End

SNP:SY-F1647E301-P An universal rack mounting kit is Installation ex works for one included in the system unit. server or subsystem. The total weight of the rack may Hereby the rack will be delivered not exceed 1000 kg! Old PRIMERGYcompletely pre-mounted and Classic 19" racks and PRIMEPOWER

all wired connections are tested. racks are not usable for the

With racks 12U, 24U, 38U: PRIMERGY BX600 S3.Systems and components will be delivered installed in the rackWith racks 46U: "Rack-mounting ex factory"

Systems and components This service is to be ordered

will be delivered separately once per installable server or

To be ordered only together with storage subsystem, in order a PRIMERGY- PRIMECENTER rack to get the server or storage e.g.: S26361-K826-V10x subsystem mounted into the

PRIMERGY Rack. refer to configurator PC-Rack In case of the 46 U PRIMERGYmax. 1x per System Rack, this service has to be

ordered, to get the mounting kits and the cables installed.

C

For more configuration information see the separate Server Blade configurator at: http://extranet.fujitsu-siemens.com/vil/pc/vil/konfiguratoren/prim-konf/xls/cnfgbx600-serverblades.xls


http://extranet.fujitsu-siemens.com/vil/pc/vil/konfiguratoren/prim-konf/xls/cnfgbx600-serverblades.xls

System configurator and order-information guideC PRIMERGY BX600 System Units Status: 2008-12-17

Section II Server Blades in System Unit BX600 S3

All described Server Blades can be mixed in on System Unit with the esplained exceptions. For more configuration information see the separate Server Blade configurator at: http://docs.fujitsu-siemens.com/dl.aspx?id=87b67d00-1751-453e-8a77-cc112afd6497

BX630 S2 Dual Socket Server BladeAMD Opteron 23xx/83xx Processors based dual socket Server Blade.max. 10x per system unit

BX630 S2 Quad Socket Server BladeAMD Opteron 83xx Processor based quad socket Server Blade.max. 5x per system unit

BX620 S4Intel Xeon DP Processor based dual socket Server Blade.max. 10x per system unit

SX650BX600 Storage BladeConnected to BX620 S4max. 5x per system unit

In case of max. configuration with120W CPUs for all 10 Server Blades, the 10th Server Blade can not be powered on in the chassis, in case of 2+2 PSU redundancy mode. Via MMB a 3+1 PSU redundancy modecan be setup to power on all server blades!

W or Y


http://docs.fujitsu-siemens.com/dl.aspx?id=87b67d00-1751-453e-8a77-cc112afd6497

System configurator and order-information guideW PRIMERGY BX600 System Units Status: 2008-12-17

Section IV on-board LAN Controllers plus Fibre Channel I/O card

Each PRIMERGY BX600 Server Blade comes with onboard Gigabit Ethernet LAN channels and special daughter card connectors for the optional FC I/O modules.

2-channel onboard LAN controller: 2-channel FC controller (daughter card option)BX620 S4: 3x controllers, 6x channels BX620 S4: 1x controller, 2x channelsBX630 S2 Dual: 2x controllers, 4x channels BX630 S2 Dual: 1x controller, 2x channelsBX630 S2 Quad: 4x controllers, 8x channels BX630 S2 Quad: 2x controllers, 4x channels

Section V GbE Switch or GbE IBP or GbE Pass-Thru Blade in NET1 / NET2 for on-board LAN Controllers

There is no Switch, IBP or Pass-Thru Blade included in the System Unit. With that System Unit 2x GbE Switch or 2x GbE IBP or 2x GbE Pass-Thru blades must be configured alternatively.The onboard LAN channels of all Server Blades are connected to two Switch / Pass-Thru / IBP blades.

S26361-F3206-E6 S26361-F3112-E1 S26361-F3206-E8 S26361-K1234-V200GbE LAN Switch Blade GbE Pass-Thru Blade GbE LAN Switch Blade GbE LAN Switch BladeL2 / L3 / L4 Switch Gbit Ethernet LAN Pass-Thru L2 / L3 / L4 Switch Cisco CBS304010x downlink / 6x uplink 10x downlink / 10x uplink 10x downlink / 6x/2x uplink 10x downlink / 6x uplink

2x Port LEDs: speed, link, activity. 2 LEDs for each port. 6x 1GbE, 2x 10GbE ext.: 2x RJ45, 4x SFPSwitch LEDs: power, status 1000 Base-T full-duplex only Port LEDs: speed, link, activity. SFP ports for RJ45 or MMF SFPsexternal 6x RJ45 connector external 10x RJ45 connector Switch LEDs: power, status max. 2x per NET1 / NET2max. 2x per NET1 / NET2 max. 2x per NET1 / NET2 external 6x RJ45 connector

external 1x CX4, 1x XFP S26361-F2749-E1

max. 2x per NET1 / NET2 Service for Blade installationin the System Unit.

Hereby the BX600 S3 willS26361-F3206-E10 be delivered completelyXFP Multi-Mode 10GBASE-SR configured and tested XFP module for 10Gbit with the Blade integrated.Ethernet FO cabling max. 1x per Switch Blademax. 1x per switch

1-2x S26361-F3024-E101S26361-F3206-E15 SFP Multi-Mode 10GBase-SR10GBASE-CX4 cable, 10m Cisco MM Fiber Module 1GbEInfiniband cable 10m length Ethernet FO cabling LC-Duplexwith CX4 connector max. 4x per switchmax. 1x per switch

S26361-F3024-E1021000 Base-T Module RJ45Cisco SFP Module RJ45 1GbEEthernet Cu cabling RJ45max. 4x per switch

S26361-F3467-E1 S26361-F3859-E1GbE LAN Switch Blade GbE Intelligent Blade Panel (IBP)L2 / L3 LAN Switch LAN Connection Blade 30x downlink / 12x uplink 30x downlink / 12x uplink2 LEDs for each port. 2 LEDs for each port.

2x 1000 Base-T full-duplex only IBP LEDs: power, statusexternal 12x RJ45 connector external 12x RJ45 connectorinstallable in NET1, NET2 of installable in NET1/2/3/4 of BX600 S3 System Unit only! BX600 S3 System Unit only!max. 2x per NET1 / NET2 max. 2x per NET1 / NET2

X

2/4

4/6/8 LAN switch #2

LAN switch #1

onboard LANcontrollers

FC I/O cards

ports

Mid-planeDual / Quad socket Server Blades

GbE IBP #1

GbE IBP #2

or

FC pass-thru #2

FC pass-thru #1FC switch #1

FC switch #2

or

LAN pass-thru #1

LAN pass-thru #2

or


System configurator and order-information guideX PRIMERGY BX600 System Units Status: 2008-12-17

Section VI Fibre Channel Switch or Pass-Thru Blade in NET3 / NET4 for FC I/O modules

The following 4Gbit Fibre Channel Switch and Pass-Thru blades are released only in combination with the 4Gbit FC I/O module S26361-F3306-E601 and only for the BX600 S3 System Unit!The FC I/O module channels of all Server Blades are connected to two Switch / Pass-Thru blades.

S26361-F3144-E16 S26361-F3144-E14 S26361-F3024-E10FC Switch Blade 1/2/4Gb/s FC Switch Blade 1/2/4Gb/s FC Pass-Thru Blade 4Gb/sBrocade SW-4016 D4 Brocade SW-4016 D4 10x downlink ports10x downlink + 6x uplink 12x selectable ports 10x uplink ports

2x Full Fabric license Full Fabric licenseAdv. Zoning, Adv. Web Tools Adv. Zoning, Adv. Web Toolsexternal: 6x connectors for external: 6x connectors for external: 10x connectors for 4Gb GBIC/SFP modules 4Gb GBIC/SFP modules 4Gb GBIC/SFP modulesmax. 2x per NET3 / NET4 max. 2x per NET3 / NET4 max. 2x per NET3 / NET4

S26361-F3024-E4 S26361-F3024-E4 S26361-F3024-E4FC GBIC/SFP Multi Mode (MMF) FC GBIC/SFP Multi Mode (MMF) FC GBIC/SFP Multi Mode (MMF)Distance: Distance: Distance:

6/10x 150/300/500m@4/2/1Gb/s 150/300/500m@4/2/1Gb/s 150/300/500m@4/2/1Gb/s1/2/4 GBit/s Fibre Channel 1/2/4 GBit/s Fibre Channel 1/2/4 GBit/s Fibre Channel requires LC connector cable requires LC connector cable requires LC connector cablemax. 6x per switch max. 6x per switch max. 10x per pass-thru

FC switch/pass-thru can only be used in fabric 2 (NET3/4) of the System Unit.Mixing of FC Switch anf FC Pass-Thru blades in one System Unit is not allowed.

End


System configurator and order-information guideY PRIMERGY BX600 System Units Status: 2008-12-17

Section VII on-board LAN Controller plus LAN I/O card

Each PRIMERGY BX600 Server Blade comes with onboard Gigabit Ethernet LAN channels and special daughter card connectors for the optional LAN I/O modules.

2-channel onboard LAN controller: 2-channel Gbit LAN controller (daughter card option)BX620 S4: 3x controllers, 6x channels BX620 S4: 1x controller, 2x channelsBX630 S2 Dual: 2x controllers, 4x channels BX630 S2 Dual: 1x controller, 2x channelsBX630 S2 Quad: 4x controllers, 8x channels BX630 S2 Quad: 2x controllers, 4x channels

Section VIII GbE Switch or GbE IBP or GbE Pass-Thru Blade in NET1 / NET2 for on-board LAN Controllers

There is no Switch, IBP or Pass-Thru Blade included in the System Unit. With that System Unit 2x GbE Switch or 2x GbE IBP or 2x GbE Pass-Thru blades must be configured alternatively.The onboard LAN channels of all Server Blades are connected to two Switch / Pass-Thru / IBP blades.

S26361-F3206-E6 S26361-F3112-E1 S26361-F3206-E8 S26361-K1234-V200GbE LAN Switch Blade GbE Pass-Thru Blade GbE LAN Switch Blade GbE LAN Switch BladeL2 / L3 / L4 Switch Gbit Ethernet LAN Pass-Thru L2 / L3 / L4 Switch Cisco CBS304010x downlink / 6x uplink 10x downlink / 10x uplink 10x downlink / 6x/2x uplink 10x downlink / 6x uplink

2x Port LEDs: speed, link, activity. 2 LEDs for each port. 6x 1GbE, 2x 10GbE ext.: 2x RJ45, 4x SFPSwitch LEDs: power, status 1000 Base-T full-duplex only Port LEDs: speed, link, activity. SFP ports for RJ45 or MMF SFPsexternal 6x RJ45 connector external 10x RJ45 connector Switch LEDs: power, status SFP modules not included:max. 2x per NET1 / NET2 max. 2x per NET1 / NET2 external 6x RJ45 connector - MMF (S26361-F3024-L101)

external 1x CX4, 1x XFP - RJ45 (S26361-F3024-L102)max. 2x per NET1 / NET2 max. 2x per NET1 / NET2

S26361-F3206-E10 S26361-F2749-E1XFP Multi-Mode 10GBASE-SR Service for Blade installationXFP module for 10Gbit in the System Unit.Ethernet FO cabling Hereby the BX600 S3 willmax. 1x per switch be delivered completely

configured and tested

2x with the Blade integrated.S26361-F3206-E15 max. 1x per Switch Blade10GBASE-CX4 cable, 10mInfiniband cable 10m lengthwith CX4 connectormax. 1x per switch

S26361-F3467-E1 S26361-F3859-E1GbE LAN Switch Blade GbE Intelligent Blade Panel (IBP)L2 / L3 LAN Switch LAN Connection Blade 30x downlink / 12x uplink 30x downlink / 12x uplink

2x 2 LEDs for each port. 2 LEDs for each port.1000 Base-T full-duplex only IBP LEDs: power, statusinstallable in NET1, NET2 of external 12x RJ45 connectorBX600 S3 System Unit only! installable in NET1/2/3/4 of max. 2x per NET1 / NET2 BX600 S3 System Unit only!

max. 2x per NET1 / NET2

Z

2/4

4/6/8

LAN switch #4

LAN switch #2

LAN switch #1

onboard LANcontrollers

LAN I/O cards

ports

Mid-planeDual / Quad socket Server Blade

LAN switch #3 GbE IBP #1

GbE IBP #2

orLAN pass-thru #1

LAN pass-thru #2

or

GbE IBP #1

GbE IBP #2

orLAN pass-thru #1

LAN pass-thru #2

or


System configurator and order-information guideZ PRIMERGY BX600 System Units Status: 2008-12-17

Section IX GbE Switch or GbE IBP or GbE Pass-Thru Blade in NET3 / NET4 for optional LAN I/O modules

S26361-F3206-E6 S26361-F3112-E1 S26361-F3206-E8GbE LAN Switch Blade GbE Pass-Thru Blade GbE LAN Switch BladeL2 / L3 / L4 Switch Gbit Ethernet LAN Pass-Thru L2 / L3 / L4 Switch10x downlink / 6x uplink 10x downlink / 10x uplink 10x downlink / 6x/2x uplink

2x Port LEDs: speed, link, activity. 2 LEDs for each port. 6x 1GbE, 2x 10GbESwitch LEDs: power, status 1000 Base-T full-duplex only Port LEDs: speed, link, activity.external 6x RJ45 connector external 10x RJ45 connector Switch LEDs: power, statusmax. 2x per NET3 / NET4 max. 2x per NET3 / NET4 external 6x RJ45 connector

external 1x CX4, 1x XFPmax. 2x per NET3 / NET4

S26361-F3206-E10S26361-F3860-E1 XFP Multi-Mode 10GBASE-SRGbE Intelligent Blade Panel (IBP) XFP module for 10Gbit LAN Connection Blade Ethernet FO cabling10x downlink / 6x uplink max. 1x per switchPort LEDs: speed, link, activity.

2x IBP LEDs: power, statusexternal 6x RJ45 connector S26361-F3206-E15installable in NET1/2/3/4 10GBASE-CX4 cable, 10mmax. 2x per NET3 / NET4 Infiniband cable 10m length

with CX4 connectormax. 1x per switch

S26361-K1234-V200 S26361-F3309-E1GbE LAN Switch Blade 10GbE LAN Switch Blade Cisco CBS3040 10GbE LAN Switch10x downlink / 6x uplink 10x downlink / 2x uplink

2x ext.: 2x RJ45, 4x SFP 2 LEDs for each port. 2 bays SFP ports for RJ45 or MMF SFPs for X2 interconnect modulesSFP modules not included: installable in NET3, NET4 of - MMF (S26361-F3024-L101) BX600 S3 System Unit only! - RJ45 (S26361-F3024-L102) max. 2x per NET3 / NET4max. 2x per NET3 / NET4

S26361-F3309-E15X2 Copper Connection Module

S26361-F2749-E1 X2 MID-PAK Copper Service for Blade installation for 10GbE LAN Switch Bladein the System Unit. max. 2x per switchHereby the BX600 S3 will

be delivered completely 1-2xconfigured and tested S26361-F3309-E20with the Blade integrated. X2 FO Connection Module max. 1x per Switch Blade X2 MID-PAK Fiber Optic

for 10GbE LAN Switch Blademax. 2x per switch

The system unit can have up to 2x GbE LAN Switch / IBP / Pass-Thru blades. If for one of the Server Blades the GbE LAN I/O module is configured, the system unit can have 4 GbE Switch / IBP / Pass-Thru blades.(see pictures above)

End



Change Report

Date Order number Changes

2008-12-12 S26361-F3860-E1 IBP 10/6 GbE meaningful in fabric 2 only2008-12-12 S26361-F3859-E1 IBP 30/12 GbE meaningful in fabric 1 only2008-12-12 S26361-K1156-V301/303 delete of BX600 S3 with MMB S22008-10-20 -severals- delete of BX600 S3 Infrastructure for ServerView PAN Manager2008-04-28 -severals- new BX600 S3 Infrastructure for ServerView PAN Manager2008-04-16 S26361-F3888-L1 Upgrade kit for BX600 S3 with MMB S2, to replace MMB S2 by MMB S3.2008-03-26 S26361-F3309-E20 X2 FO Connection Module - as soon as available2008-03-26 S26361-F3309-E15 X2 Copper Connection Module - as soon as available2008-03-26 S26361-F3309-E1 10GbE LAN Switch Blade - as soon as available2008-03-20 S26361-F3113-E1 Adv. KVM Switch Blade no longer available2008-02-22 S26361-K1234-V200 New order number for Switch Blade CBS30402008-02-14 S26361-F3309-E20 New Interconnect modules for 10GbE LAN Switch Blade - as soon as available2008-02-14 S26361-F3309-E15 New Interconnect modules for 10GbE LAN Switch Blade - as soon as available2008-02-14 S26361-F3309-E1 New 10GbE LAN Switch Blade for BX600 S3 - as soon as available2008-02-14 S26361-F3024-E10 New 4Gb FC Pass-Thru for BX600 S32008-01-31 S26361-K920-V201 EOL for System Unit BX600 S22007-11-19 EOL for BX620 S3 2007-09-13 S26361-F3860-E1

S26361-F3859-E1 new IBP products


bx600

Documents