primergy bx630 s2 scalable server blade - options...

PRIMERGY BX630 S2Scalable Server Blade Options Guide

Edition October 2007

Comments… Suggestions… Corrections…The User Documentation Department would like toknow your opinion of this manual. Your feedback helpsus optimize our documentation to suit your individual needs.

Feel free to send us your comments by e-mail to [email protected].

Certified documentation according to DIN EN ISO 9001:2000To ensure a consistently high quality standard anduser-friendliness, this documentation was created tomeet the regulations of a quality management system which complies with the requirements of the standardDIN EN ISO 9001:2000.

cognitas. Gesellschaft für Technik-Dokumentation mbHwww.cognitas.de

Copyright and Trademarks

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-260

5-0

01.fm

Copyright © 2007 Fujitsu Siemens Computers GmbH.

All rights reserved. Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trade names and/or trademarks of their respective manufacturers.

mailto:[email protected]

http://www.cognitas.de

BX630 S2 Options Guide

Contents

1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Concept and target groups . . . . . . . . . . . . . . . . . . . 5

1.2 Documentation overview . . . . . . . . . . . . . . . . . . . . 5

1.3 Extensions and conversions . . . . . . . . . . . . . . . . . . 7

1.4 Structure of the server blade . . . . . . . . . . . . . . . . . . 8

1.5 Configurations . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.6 Notational conventions . . . . . . . . . . . . . . . . . . . . 12

2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 15

4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.1 Installing a second processor . . . . . . . . . . . . . . . . . 23

6 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.1 Fitting rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.2 Replacing memory modules . . . . . . . . . . . . . . . . . . 34

7 Optional I/O module . . . . . . . . . . . . . . . . . . . . . . 37

7.1 Installing an I/O daughter card . . . . . . . . . . . . . . . . 41

Options Guide BX630 S2

Contents

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-260

6-0

01.fm

8 Replacing the battery . . . . . . . . . . . . . . . . . . . . . . 43

9 Upgrading to a quad-socket server blade . . . . . . . . . . . 45

9.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

9.2 Assembly instructions . . . . . . . . . . . . . . . . . . . . . 47

10 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

10.1 Closing the server blade . . . . . . . . . . . . . . . . . . . . 57

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

BX630 S2 Options Guide 5

1 PrefaceThe PRIMERGYBX630 S2 scalable server blade is an AMD-based server blade designed for the PRIMERGY BX600 S3 basic unit. It can also be operated in slots 1-3 and 5-9 of the BX600 S2 basic unit. The BX630 S2 scalable server blade can be installed as a dual-socket server blade or, in a multi-blade config-uration, as a quad-socket server blade.

1.1 Concept and target groups

This Options Guide shows you how to extend and upgrade your server.

V CAUTION!

The activities described in this manual may only be performed by technical specialists.

I The installation and removal of the hot-plug components is described in the Operating Manual supplied with the server.

1.2 Documentation overview

More information on your PRIMERGY BX630 S2 can be found in the following documents:

– “Quick Start Software - Quick Installation Guide” leaflet (only included as a printed copy)

– “Safety notes and other important information” manual

– “Warranty” manual

– “Ergonomics” manual

– “Returning used devices” manual

– “Helpdesk” leaflet

– “PRIMERGY BX630 S2 Server Operating Manual”

I PRIMERGY manuals are available in PDF format on the ServerBooks DVD. The ServerBooks DVD is part of the ServerStart Suite supplied with every server.

6 Options Guide BX630 S2

Documentation overview Preface

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-260

7-0

01.fm

The PDF files of the manuals can also be downloaded free of charge from the Internet. The overview page showing the online documentation available on the Internet can be found using the URL: http://manuals.fujitsu-siemens.com. The PRIMERGY server documentation can be accessed using the Industry standard servers navigation option.

If you need a replacement copy of the ServerBooks DVD, send the details of your server to the following e-mail address: [email protected]

Further sources of information:

– Manual for the monitor– Documentation for boards and drives– Documentation for your operating system– Information files on your operating system

http://manuals.fujitsu-siemens.com




Preface Extensions and conversions

1.3 Extensions and conversions

Second processor

If only one processor is installed in your server blade, you can upgrade it to include a second one. You may only use processors of the same type in the server blade. The second processor must have the same clock frequency as the first.

Extending the main memory

The system board of the BX630 S2 scalable server blade has four memory banks with two 184-pin DDR2 DIMM slots each. This allows a maximum memory configuration of 32 GB. Each memory bank can be fitted with 512 Mbyte, 1 Gbyte, 2 Gbyte or 4 Gbyte registered DDR2 667 MHz PC2-5300 memory modules.

The two memory modules of one bank must always be fitted in pairs and have the same capacity.

Optional I/O module

The server blade can be equipped with a 4-Gbit FC I/O module or a 1-Gbit Ethernet I/O module.

To allow use of the additional I/O functionality, at least one FC pass-thru blade (or switch blade) or Ethernet LAN pass-thru blade (or switch blade) must be installed in the NET3 and/or NET4 slots of the PRIMERGY BX600 basic unit.

Multi-blade configuration

You can upgrade the BX630 S2 scalable server blade to a quad-socket server blade by connecting two dual-socket server blades, see section “Configura-tions” on page 10.


Structure of the server blade Preface

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-260

7-0

01.fm

1.4 Structure of the server blade

Figure 1: PRIMERGYBX630 S2 scalable server blade

The above figure shows the positions of the most important components of the PRIMERGYBX630 S2 scalable server blade.

2

1

3

4

6

78

5

10

9


Preface Structure of the server blade

1 CPU 1 and heat sink

2 DIMM slots for four DDR2 667 modules (two banks, assigned to CPU1)

3 Lithium battery

4 DIMM slots for four DDR2 667 modules (two banks, assigned to CPU2)

5 DIP switch SW4 (user switch)

6 Control panel board with connection cable

7 2.5-inch SAS/SATA-II hard disk module 1

8 2.5-inch SAS/SATA-II hard disk module 2

9 CPU 2 and heat sink

10 Position for a 4-Gbit FC daughter card or a 1-Gbit Ethernet daughter card (optional I/O module)


Configurations Preface

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-260

7-0

01.fm

1.5 Configurations

The PRIMERGY BX630 S2 scalable server blade can be installed as a dual-socket server blade or as a quad-socket server blade. The possible configura-tions are shown in the following diagrams.

Dual-socket server blade

Figure 2: PRIMERGY BX630 S2 dual-socket server blade

Processor Hard disksI/O moduleMain memory

Basic configuration

Optional module

Opteron CPU 2FC or GbE

I/O module oremtpy

SAS/SATA Bank 4 (2 modules)

Opteron CPU 1

Bank 3 (2 modules)

Bank 2 (2 modules)

Bank 1 (2 modules)

SAS/SATA

onboard

2.5" HDD module

controller

or dummy module

SAS/SATA 2.5" HDD moduleor dummy module


Preface Configurations

Quad-socket server blade

The following figure shows the possible configurations of a PRIMERGY BX630 S2 quad-socket server blade.

Figure 3: PRIMERGY BX630 S2 quad-socket server blade

Processor Hard disksI/O moduleMain memory

Basic configuration

Optional module

Master

Opteron CPUSAS Bank 1 (2 modules)

Opteron CPU

Bank 2 (2 modules)

Bank 3 (2 modules)

Bank 4 (2 modules)

SAS/SATA

onboard

2.5" HDD module

controller

or dummy module

SAS 2.5" HDD moduleor dummy module

FC or GbE I/O module or

empty

Slave

Opteron CPUSAS Bank 5 (2 modules)

Opteron CPU

Bank 6 (2 modules)

Bank 7 (2 modules)

Bank 8 (2 modules)

SAS/SATA

onboard

2.5" HDD module

controller

or dummy module

SAS 2.5" HDD moduleor dummy module

FC or GbE I/O module or

empty


Notational conventions Preface

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-260

7-0

01.fm

1.6 Notational conventions

The following notational conventions are used in this manual:

Text in italics indicates commands or menu items.

“Quotation marks” indicate names of chapters and terms that are being emphasized.

Ê describes activities that must be performed in the order shown.

V CAUTION! pay particular attention to texts marked with this symbol. Failure to observe this warning may endanger your life, destroy the system or lead to the loss of data.

I indicates additional information, notes and tips.


2 ProcedureV CAUTION!

● The actions described in this manual should only be performed by technical specialists.

● Equipment repairs should only be performed by service staff.

● Any failure to observe the guidelines in this manual, and any unautho-rized opening or improper repairs could expose the user to risks (electric shock, energy hazards, fire hazards) or damage the equipment.

● Please note that any unauthorized opening of the server will void the warranty and exempt the manufacturer from all liability.

Ê First of all please familiarize yourself with the safety instructions in the chapter “Safety instructions” on page 15.

Ê Make sure that all the manuals you need are available and print out the PDF files if necessary. You will definitely need the operating manuals of the server blade and of your BX600 S2 or BX600 S3 basic unit.

Ê Shut down the server blade correctly, switch it off and remove it from the basic unit as described in the Completion.

Ê Extend or upgrade your server blade as described in the relevant chapter.

I The installation and removal of the hot-plug components is described in the Operating Manual supplied with the server blade.

Ê Close the server blade, place it back in the basic unit and switch on the server blade as described in chapter “Completion” on page 57.

Ê Start the operating system and, if necessary, configure it as required (see the Operating Manual).

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-260

8-0

01.fm


3 Safety instructionsI The following safety instructions are also provided in the manual “Safety

notes and other important information”.

This device meets the relevant safety regulations for IT equipment. If you have any questions about whether you can install the server in the intended environment, please contact your sales outlet or our customer service team.

V CAUTION!

● The actions described in this manual should only be performed by technical specialists.

● Equipment repairs should only be performed by service staff.

● Any failure to observe the guidelines in this manual, and any unautho-rized opening or improper repairs could expose the user to risks (electric shock, energy hazards, fire hazards) or damage the equipment.

● Please note that any unauthorized opening of the server will void the warranty and exempt the manufacturer from all liability.

Before starting up

V CAUTION!

● During installation and before operating the device, observe the instructions on environmental conditions for your device.

● If the device is brought in from a cold environment, condensation may form both inside and on the outside of the device.

Wait until the device has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the device if this requirement is not observed.

● Transport the device only in the original packaging or in packaging that protects it from knocks and jolts.

Installation and Operation

V CAUTION!

● Read the notes on installation and operation in the operating manual for your BX600 S2 or BX600 S3 basic unit.


Safety instructions

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-260

9-0

01.fm

V CAUTION!

● When installing the server blade in the basic unit, beware of the energy hazard at the midplane contacts. A short-circuit on these contacts may damage the system.

● Data cables must be adequately shielded to avoid interference.

● For the LAN wiring, the requirements according to standards EN 50173 and EN 50174-1/2 apply. The minimum requirement is the use of a protected LAN line of category 5 for 10/100 Mbps Ethernet, and/or category 5e for Gigabit Ethernet. The requirements of the specification ISO/IEC 11801 must also be taken into account.

● Route the cables in such a way that they do not form a potential hazard (tripping) and cannot be damaged. When connecting the device, refer to the relevant notes in the Operating Manual.

● Do not connect or disconnect any data transmission cables during a thunderstorm (lightning hazard).

● Be careful to ensure that no objects (e.g. jewelry, paper clips etc.) or liquids get inside the device (electric shock, short circuit).

● In emergencies (e.g. damaged casing, control elements or cables, penetration of liquids or foreign bodies), switch off the device immedi-ately, unplug it from the grounded power outlets, and contact your customer service center.

● Proper operation of the device (in accordance with IEC60950/EN 60950) is only ensured if the casing is completely assembled and the rear covers for the installation openings are in place (electric shock, cooling, fire protection, interference suppression).

● Install only system extensions that satisfy the requirements and rules governing safety, electromagnetic compatibility, and telecommunica-tions terminal equipment.

If you install other extensions, you may damage the system or violate these safety regulations.

Information on which system extensions are suitable can be obtained from the customer service center or your sales outlet.


Safety instructions

V CAUTION!

● The components marked with a warning label (e.g. lightning symbol) may only be opened, removed, or exchanged by authorized, qualified personnel, with the exception of the hot-plug/hot-swap components.

● If you cause a defect on the device by installing or exchanging system extensions, the warranty will be invalidated.

● Only set the resolutions and refresh rates specified in the operating manual for your monitor.

Otherwise, you may damage the monitor. If you are in any doubt, contact your sales outlet or customer service center.

Batteries

V CAUTION!

● Incorrect replacement of batteries can lead to risk of explosion. The batteries may only be replaced with identical batteries or with a type recommended by the manufacturer (see Options Guide).

● Do not throw batteries into the trash can. They must be disposed of in accordance with local regulations on special waste.

● The German battery act obligates consumers in Germany to return waste batteries to the distributor or to the return points established by the public waste management authorities.

● Replace the lithium battery on the system board only as described in the Options Guide.

● All batteries containing pollutants are marked with a crossed-out garbage can accompanied by the chemical symbol of the heavy metal that classifies the battery as a pollutant:

Cd Cadmium

Hg Mercury

Pb Lead


Safety instructions

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-260

9-0

01.fm

Modules with electrostatic-sensitive components

Systems and components that might be damaged by electrostatic discharge (ESD) are marked with the following label:

Figure 4: ESD label

When you handle components fitted with ESDs, you must observe the following points under all circumstances:

● Remove the power plug before installing or removing components containing ESDs.

● You must always discharge yourself of static charges (e.g. by touching a grounded object) before working.

● The equipment and tools you use must be free of static charges.

● Only touch the components at the positions highlighted in green (touch points).

● Do not touch any exposed pins or conductors on a component.

● Use a grounding cable designed for this purpose to connect yourself to the system unit as you install components.

● Place all components on a static-safe base.

I You will find a detailed description for handling ESD components in the relevant European or international standards (DIN EN 61340-5-1, ANSI/ESD S20.20).


4 PreparationV CAUTION!

Please observe the safety information in the chapter “Safety instructions” on page 15.

Ê Exit all applications and shut down the server blade correctly.

Ê Press the On/Off button on the server blade control panel.

Removing the server blade from the basic unit

Figure 5: Disengaging the server blade

Ê Press the two touch points (1) to unlock the handles.

Ê Open out the two handles (2) simulta-neously to disengage the server blade.

1

2

2

1


Preparation

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

0-0

01.fm

Figure 6: Removing the server blade from the basic unit

Ê Pull the server blade out of the basic unit.


Preparation

Removing the housing cover

Figure 7: Removing the housing cover

Ê Undo the two knurled screws (1).

Ê Push the housing cover as far as possible in the direction of the arrow (2).

Ê Take off the housing cover.

The server blade components are now freely accessible (see figure 1 on page 8).

11

2

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

0-0

01.fm


5 ProcessorsV CAUTION!

Make sure you observe the safety notes in the chapter “Safety instruc-tions” on page 15.

Processors are components which are extremely sensitive to electro-static discharge and must be handled with caution.

When you take a processor out of its protective wrapper or out of a socket, place it on an insulated, antistatic surface with the smooth side down.

Never slide a processor over a surface.

5.1 Installing a second processor

The BX630 S2 dual-socket server blade can be upgraded with a second processor. The upgrade kit includes a processor and a heat sink.

V CAUTION!

Always use processors of the same type. All processors must have the same frequency and cache size. For multi-processor mode use a suitable multi-processor operating system.

Ê Open the server blade as described in the chapter “Preparation” on page 19.

I The BX630 S2 server blades may have two different processor sockets, see figure 8:


Installing a second processor Processors

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

1-0

01.fm

Figure 8: Processor socket variants

The following section describes how to install a processor in the Foxconn processor socket. Differences in handling a Tyco processor socket are indicated in the relevant steps.

Figure 9: Processor socket variant 1: Opening the socket

Ê Remove the protective cover by lifting it at the edge (1).

Ê Release the locking lever (2) by first pressing it down and then swiveling it up as far as it will go.

Foxconn processor socket Tyco processor socket

1

2


Processors Installing a second processor

Figure 10: Processor socket variant 1: Opening the locking frame

Ê Swivel the locking lever of the processor socket upward.

Ê Remove the processor from its protective wrapper.



© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

1-0

01.fm

Figure 11: Inserting the processor (Foxconn socket)

Ê Position the new processor above the socket, and press it carefully into the socket.

V CAUTION!

The processor can only be installed in one direction. Make sure that the recesses on the processor (A) are aligned with the corresponding positioning elements (lugs) on the socket.

I The Tyco processor socket only has positioning elements on one side, see (A) in figure 12.

Figure 12: Processor socket variant 2: Inserting the processor

A

A



Figure 13: Locking the processor (Foxconn socket)

Ê Fold the locking frame of the processor socket down.

Ê Swivel the locking lever of the socket down.

Ê Lock the locking lever by pressing it under the bracket (1) on the processor socket.

1



© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

1-0

01.fm

V CAUTION!

When locking the Tyco processor socket, make sure that the small clips on the locking frame (A) slide under the corresponding brackets on the outer socket frame, see figure 14.

Figure 14: Locking the processor (Tyco processor socket)

A



Installing the heat sink

Figure 15: Preparing the heat sink

Ê Remove the yellow tape from the underside of the heat sink, and then remove the transparent cover protecting the thermal paste.



© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

1-0

01.fm

Figure 16: Fastening the heat sink

Ê Place the heat sink on the processor and fix it with the three supplied screws. Fasten the screws in the order shown in the figure.

1

2 3


6 MemoryThe system board of the PRIMERGYBX630 S2 scalable server blade has four memory banks, comprising eight slots, which can be fitted in pairs with 512 MB, 1 GB, 2 GB or 4 GB DDR2 667 memory modules. The board supports a maximum memory configuration of 32 GB.

Figure 17: PC3200 DDR SDRAM module

The memory modules are marked with a dent (A) so that you cannot install them the wrong way round.

A


Fitting rules Memory

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

2-0

01.fm

6.1 Fitting rules

Figure 18: Slot numbering for memory modules

Slots DIMM 1 through DIMM 4 are assigned to CPU1. Slots DIMM 5 through DIMM 8 are assigned to CPU 2, i.e. they can only be fitted if CPU 2 is installed. The following rules also apply:

● The DIMM slots must be fitted one bank at a time. A memory bank comprises two DIMM slots.

● The two DIMM modules of one bank must have the same type (identical capacity, identical clock rate, single ranked or dual ranked).

If only CPU 1 is installed:

– Start with DIMM 1+2 followed by DIMM 3+4.

If CPU 1 and CPU 2 are installed:

– Start with DIMM 1+2 followed by DIMM 5+6, then DIMM 3+4 followed by DIMM 7+8.

DIMM 1DIMM 2

DIMM 3DIMM 4

DIMM 5DIMM 6

DIMM 7DIMM 8

CPU 1

CPU 2


Memory Fitting rules

If you have a quad-socket configuration:

– Start with DIMM 1+2 followed by DIMM 5+6 in the master module, then DIMM 1+2 followed by DIMM 5+6 in the slave module.

Install additional DIMMs in DIMM 3+4 followed by DIMM 7+8 in the master module, followed by DIMM 3+4 and DIMM 7+8 in the slave module.

● If you install memory modules for a CPU which have different memory capacities, you must first install the modules with the lower memory capacity.


Replacing memory modules Memory

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

2-0

01.fm

6.2 Replacing memory modules

V CAUTION!

● Note the safety instructions and the information on handling electro-statically sensitive devices on page 18.

● Install the memory modules very carefully. Too much pressure can damage the ejection tabs.

Ê Remove the server blade from the basic unit and open it as described in the chapter “Preparation” on page 19.

Figure 19: Removing a memory module

Ê Fold the tabs outwards on both sides of the relevant slot (1).

Ê If a memory module was already installed in the slot: Remove the memory module from the slot (2).

1

1

2


Memory Replacing memory modules

Figure 20: Installing a memory module

Ê Carefully press the memory module into the slot (1) until the fastening tabs on both sides of it engage (2).

Ê Close the server blade, insert it in the basic unit and switch it on as described in chapter “Completion” on page 57.

2

2

1

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

2-0

01.fm


7 Optional I/O moduleThe PRIMERGYBX630 S2 dual-socket server blade can be equipped with an additional I/O module. For this purpose, the server blade has a special slot for an extension board (I/O daughter card) (see figure 24 on page 41). The following I/O daughter cards are available for the BX630 S2 server blade:

– 4-Gbit Fibre Channel daughter card (PCIe)– 1-Gbit Ethernet daughter card (PCIe)– 10-Gbit Ethernet daughter card (PCIe)

I To allow use of the additional I/O functionality, at least one FC I/O blade or an Ethernet I/O blade must be installed in slot NET3 and/or NET4 of the PRIMERGY BX600 S2 or BX600 S3 basic unit. For further infor-mation on I/O blades, see the operating manual for your basic unit.

It is not possible to mix Fibre Channel I/O blades and Ethernet I/O blades in slots NET3 and NET4 of the basic unit.


Optional I/O module

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

3-0

01.fm

4-Gbit Fibre Channel daughter card (PCIe)

Figure 21: 4-Gbit Fibre Channel daughter card (PCIe)

The 4-Gbit FC daughter card (PCIe) provides two independent serial 1/2/4-Gbit/s FC ports. It is fitted with an Emulex chip and supports multiple FC storage subsystems of the corresponding versions.

I The 4-Gbit FC daughter card can only be used in combination with the 4/4-Gbit FC switch blade. For more information, see the BX600 S3 operating manual.

The 4-Gbit FC option is only supported by the BX600 S3 basic unit.


Optional I/O module

1-Gbit Ethernet daughter card (PCIe)

Figure 22: Gbit Ethernet daughter card (PCIe)

The 1-Gbit Ethernet daughter card (PCIe) has two Broadcom 5708S chips and provides two 1-Gbit/s Ethernet ports. TOE (TCP/IP Offload Engine) and iSCSI/iSCSI Boot are supported.


Optional I/O module

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

3-0

01.fm

10-Gbit Ethernet daughter card (PCIe)

Figure 23: 10-Gbit Ethernet daughter card (PCIe)

The 10-Gbit Ethernet daughter card (PCIe) provides two 10-Gbit/s Ethernet ports. This module also supports TOE (TCP/IP Offload Engine) and iSCSI/iSCSI Boot.

I The 10-Gbit Ethernet daughter card (PCIe) can only be used in combi-nation with the 10-Gbit switch blade 10/2. For further information, see the operating manual for your BX600 S2 or BX600 S3 basic unit.


Optional I/O module Installing an I/O daughter card

7.1 Installing an I/O daughter card

V CAUTION!

● Please observe the safety information in the chapter “Safety instruc-tions” on page 15

Ê Remove the server blade from the basic unit and open it as described in the chapter “Preparation” on page 19.

Figure 24: Position for an I/O daughter card

Ê Place the I/O daughter card onto the two sockets (A).

Ê Fasten the I/O daughter card with three screws. The corresponding nuts on the system board are indicated by arrows in figure 24.

A

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

3-0

01.fm


8 Replacing the batteryTo allow permanent saving of the system information, a lithium battery is installed which supplies the CMOS memory with power. If the battery charge is too low or the battery is empty, a corresponding error message is displayed. In this case, the lithium battery must be replaced.

V CAUTION!

Observe the safety notes and the information on handling batteries in the section “Batteries” on page 17. Incorrect replacement of batteries may result in a risk of explosion. The batteries must be replaced with an identical battery or with a battery type recommended by the manufac-turer. Make sure you insert the battery correctly. The positive pole must face toward the inside of the server blade.

Figure 25: Replacing the battery

Ê Press the locking lever in the direction of the arrow (1) and remove the battery from its carrier (2).

Ê Insert a new lithium battery of identical type into the carrier (3) and engage it with the lever (4).

1

2

3

4

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

4-0

01.fm


9 Upgrading to a quad-socket server blade

This chapter describes how to connect two BX630 S2 dual-socket server blades to form a quad-socket server blade.

9.1 Overview

Figure 26: PRIMERGY BX630 S2 quad-socket server blade

The above figure shows a BX630 S2 quad-socket server blade as it is installed in the BX600 S2 or BX600 S3 basic unit. The master module is on the right side, identifiable by the handles and the control elements (A) on the control panel board. The slave module has the handles removed and the control panel has been replaced by a dummy module. The slave module has a fixed connection to the housing cover of the master module.

The two modules of the quad-socket server blade exchange data through small circuit boards with printing on both sides, see Quad-socket upgrade kit.

I In a PRIMERGY BX630 S2 quad-socket server blade, only processors of the Opteron 83xx MP series are allowed.

A


Overview Upgrading to a quad-socket server blade

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

5-0

01.fm

Quad-socket upgrade kit

The quad-socket upgrade kit for connecting two PRIMERGY BX630 S2 dual-socket server blades to form a quad-socket server contains the following elements.

Figure 27: Side-band element

The side-band element connects the server management bus of the master module to that of the slave module, see also “Inserting the HT-link elements and the side-band element” on page 53.

Figure 28: HT-link element

Two HyperTransport link elements (HT-link elements) connect the system bus of the master module and the system bus of the slave module, see also “Inserting the HT-link elements and the side-band element” on page 53.


Upgrading to a quad-socket server blade Assembly instructions

Figure 29: Guide element for HT-link elements and side-band elements and countersunk screws.

Three plastic guide elements ensure the exact positioning of the HT-link elements and side-band elements during installation. These guide elements are fastened to the housing cover of the master module, see also “Preparing the housing cover of the master module” on page 50.

Figure 30: Shoulder screws for fastening the slave module

The slave module is fastened to the housing cover of the master module with 5 shoulder screws, see also page 51.

9.2 Assembly instructions

The following section describes the steps you need to perform to upgrade the server blade to a quad-socket server blade. The links take you to the sections with the descriptions of the individual steps.

– Removing the handles of the slave module– Removing the control panel board of the slave module– Preparing the housing cover of the master module– Fastening the housing cover of the master module to the slave module– Closing the master module– Inserting the HT-link elements and the side-band element


Assembly instructions Upgrading to a quad-socket server blade

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

5-0

01.fm

Removing the handles of the slave module

The quad-socket server blade is locked in the BX600 S2 or BX600 S3 basic unit using the handles of the master module. You must remove the handles of the slave module.

Figure 31: Removing the handles

Ê Remove the housing cover of the slave module, see page 21.

Ê Undo the pins of the joints (A) with a Philips screwdriver and remove them from the housing. Remove the handles.

Removing the control panel board of the slave module

Figure 32: Control panel board with connection cable

A



The quad-socket server blade is controlled via the control panel of the master module. You must remove the control panel board of the slave module.

Figure 33: Removing the control panel board

Ê Undo the two screws (1) fastening the control panel board to the server blade housing.

Ê Loosen the clamping bracket (2) and disconnect the cable of the control panel board from the connector on the system board.

Figure 34: Removing the control panel board

Ê Remove the control panel board with the connection cable from the server blade housing.

12



© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

5-0

01.fm

Preparing the housing cover of the master module

Mount the guides for the exact positioning of the HT-link elements and the side-band element on the underside of the master module housing cover figure 35 shows a prepared housing cover.

Figure 35: Housing cover of the master module (underside with guides for the link elements)

Ê Remove the housing cover of the master module, see page 21.

Figure 36: Housing cover of the master module with guide elements

Ê Fasten each guide element with two countersunk screws.



Fastening the housing cover of the master module to the slave module

Figure 37: Fastening the housing cover of the master module to the slave module

Ê Place the prepared housing cover of the master module on the underside of the slave module.

Ê Fasten the housing cover of the master module with 5 screws. The screw holes are indicated by arrows in figure 37.



© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

5-0

01.fm

Closing the master module

Figure 38: Closing the master module

Ê Turn the slave module over so that the housing cover of the master module and the guide elements face down. Carefully place the slave module onto the housing of the master module such that it projects 1-2 cm at the back. Make sure that the slave module lies flush with both sides of the master module.

Ê Push the slave module in the direction of the arrow as far as it will go.

Ê Fasten the two green knurled screws (A).

A



Inserting the HT-link elements and the side-band element

The two modules of the quad-socket server blade exchange data through two HT-link elements and the side-band element. These double-sided printed circuit boards are plugged into special sockets on the system boards and connect the bus systems of the two modules.

Figure 39: Connection with an HT-link element

The figure above shows a diagram of the connection between the system board of the master module (1) and the system board of the slave module (2) by way of an HT-link element (3).

1

2

3



© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

5-0

01.fm

The figure below shows the positions of the sockets for the HT-link elements (a, b) and the side-band element (c) on the BX630 S2 system board.

Figure 40: Position of the sockets for the HT-link and side-band elements

V CAUTION!

Make sure you insert the link elements with the correct side facing the front as shown in the following figures.

CPU1

CPU2

b

a

c



Figure 41: Inserting the side-band element

Ê Insert the side-band element in the socket (A). The metal edge (B) must face inward.

Figure 42: Installed side-band element

Ê Carefully press the side-band element down as far as it will go.

A

B



© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

5-0

01.fm

Figure 43: Installing the HT-link elements

Ê Insert the HT-link elements in the sockets. The metal edges (A) must face outward.

Figure 44: Installed HT-link elements

Ê Carefully press the HT-link elements down as far as they will go.

This completes the upgrade to a quad-socket server blade. Now proceed as described in the chapter “Completion” on page 57.

A

A


10 CompletionV CAUTION!

Please observe the safety information in the chapter “Safety instructions” on page 15.

10.1 Closing the server blade

Figure 45: Closing the housing cover

Ê Place the housing cover onto the server blade such that it projects 1-2 cm at the back.

Ê Push the housing cover forward as far as possible (1).

Ê Fasten the two green knurled screws (2).

Ê Insert the server blade in the basic unit.

I To install the server blade in the basic unit, perform the procedure described in the chapter “Preparation” on page 19 in reverse.

1

22

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

6-0

01.fm


AbbreviationsASR&R

Automatic Server Reconfiguration and Restart

ATAAdvanced Technology Attachments

BIOSBasic Input-Output System

CDCompact Disk

COMCommunication

CPUCentral Processing Unit

DBMSDatabase Management System

DDRDouble Data Rate (RAM)

DIMMDual Inline Memory Module

DVDDigital Versatile Disk

ECCError Correcting Code

EDCError Detection Code

EMCElectromagnetic Compatibility


Abbreviations

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

7-0

01.fm

ESDElectrostatic Discharge

FCFibre Channel

GAMGlobal Array Manager

HDDHard Disk Drive

HUHeight Unit

I/OInput/Output

IDIdentification

IDEIntegrated Drive Electronics

IPInternet Protocol

iSCSIInternet SCSI

LANLocal Area Network

LCDLiquid Crystal Display

LEDLight-Emitting Diode

MRLManually Retention Latch


Abbreviations

NICNetwork Interface Card

NMINon Maskable Interrupt

PCIPeripheral Component Interconnect

PDAPrefailure Detection and Analyzing

POSTPower On Self Test

PSUPower Supply Unit

RAIDRedundant Arrays of Independent Disks

ROMRead-Only Memory

SANStorage Area Network

SASSerial Attached SCSI

SATASerial ATA

SCASingle Connector Attachment

SCSISmall Computer System Interface

SCUServer Configuration Utility


Abbreviations

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

7-0

01.fm

SFPSmall Form Factor Pluggable

USBUniversal Serial Bus

VGAVideo Graphics Adapter

VPDVital Product Data

WOLWakeup on LAN


IndexBbattery

replace 43server blade 43

Ddocumentation

overview 5

EESD (devices sensitive to electrostatic

discharge) 18Ethernet

optional I/O module 37

FFibre Channel

optional I/O module 37fitting rules

SDRAM modules 32

HHT-link element 46

II/O daughter card 37

1-Gbit Ethernet (PCIe) 394-Gbit Fibre Channel (PCIe) 38

information material, additional 6

LLithium battery 17lithium battery 43

Mmain memory

extend 7meaning of the symbols 12

Nnotational conventions 12

Ooptional I/O module 37

Pprocessor

add 7

Qquad-socket upgrade

assembly instructions 47–56overview 45upgrade kit 46

Rreplace

battery 43

SSDRAM 31

fitting rules 32server blade

battery 43close 57open 21remove from basic unit 19

side-band element 46slave module, prepare

remove control panel board 48remove handles 48

Ttarget group 5

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

ume

ntat

ion

mb

H 2

007

P

fad:

W:\A

nw

endu

ngs

date

n\F

CT

\tim

_lo

cal\w

ork\

WA

LTE

R\O

BJ_

DO

KU

-261

8-0

01.fm

Information on this document On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Compu-ters. This new subsidiary of Fujitsu has been renamed Fujitsu Technology So-lutions.

This document from the document archive refers to a product version which was released a considerable time ago or which is no longer marketed.

Please note that all company references and copyrights in this document have been legally transferred to Fujitsu Technology Solutions.

Contact and support addresses will now be offered by Fujitsu Technology So-lutions and have the format …@ts.fujitsu.com.

The Internet pages of Fujitsu Technology Solutions are available at http://ts.fujitsu.com/... and the user documentation at http://manuals.ts.fujitsu.com.

Copyright Fujitsu Technology Solutions, 2009

Hinweise zum vorliegenden Dokument Zum 1. April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von Fujitsu übergegangen. Diese neue Tochtergesellschaft von Fujitsu trägt seit-dem den Namen Fujitsu Technology Solutions.

Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine bereits vor längerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche Produktversion.

Bitte beachten Sie, dass alle Firmenbezüge und Copyrights im vorliegenden Dokument rechtlich auf Fujitsu Technology Solutions übergegangen sind.

Kontakt- und Supportadressen werden nun von Fujitsu Technology Solutions angeboten und haben die Form …@ts.fujitsu.com.

Die Internetseiten von Fujitsu Technology Solutions finden Sie unter http://de.ts.fujitsu.com/..., und unter http://manuals.ts.fujitsu.com finden Sie die Benutzerdokumentation.

Copyright Fujitsu Technology Solutions, 2009

primergy bx630 s2 scalable server blade - options...

Documents