STATISTICAL COUNTERS Imlct:spg=0;                                         ! To access counters in non-APG 40 BSCs !Sdtdp:rptid=101,objtype=celtchf,obj=xx,int=15; ! Drops and Traffic for 15 minutes !Sdtdp:rptid=165,objtype=cltchdrf,obj=xx,int=15;              ! Detailed Drops for last 30 minutes !Sdtdp:rptid=151,objtype=ncellrel,obj=xx,int=1; ! Handover stats within BSC for last hour !Sdtdp:rptid=150,objtype=necellrel,obj=xx,int=2; ! Handover stats to site outside BSC for last 2 hours !Sdtdp:rptid=210,int=15; ! Drops per Timeslot report for all day yesterday !Sdtdp:rptid=234,objtype=celtchh,obj=xx,int=24; ! HR Drops for all day yesterday !Sdtdp:rptid=241,objtype=cltchdrah,obj=xx,int=24,per=cur; ! Detailed HR Drops for all day today !End;                                                        ! To get out of counters ! Aploc; ! To access counters in APG 40 BSCs !Stmfo -i -z LF -b 200408010000 -s 200408010900 -d drops_til_9am_aug01 CELTCHF

! Drops and Traffic from midnight to 9 am !Stmfo -i -z LF -b 200408010000 -s 200408010900 -d detaileddrops_9am_aug01 CLTCHDRF

! Detailed Drops !

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

GPRS ALARMS(//NSVCI)Rrgbp;                                                    ! Prints Sites on BSC data state !Rrvbi:nsvci=13562;                              ! Blocks down NSVCi !Rrnse:nsvci=13562;                            ! Takes the NSVCi OOS !Rrnsi:nsvci=13562;                             ! Restores NSCVi to service !Rrvbe:nsvci=13562;                            ! Deblocks NSVCi !Radrp:dev=RTGPHDV-64;                 ! Prints RP !Blrpi:rp=483;                                         ! Block & Deblock RP if West Coast recommends !Rlgrp:cell=abc123a;                           ! Print # of active pdch on cell !Rlgsp:cell=abc123a;                           ! Print gprs data for cell !

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 

Transcoder Pool Self Config TimeoutRrpar;                                                     ! Resets alarm, if continually comes in assign to Tier 2 !

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

 Transcoder Pool Mean Hold Time

Rrmsp:trapool=all;Rrmse:trapool=all; !or trapool=x!Rrmsi:trapool=all,acl=a2;

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 

Transcoder Pool blockingRrtpp:trapool=all,printdev;Rrtpi:trapool=x;                                    ! Blocks trapool !Rrtpe:trapool=x;                                   ! Deblocks trapool !Rrtpp:trapool=x,printdev;                    ! Prints all devices belonging to transcoder pool !

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

 

ABIS Path UnavailableRxapp:mo=rxotg-10;                           ! Abis Path status !Rxapi:mo=rxotg-10,dcp=10,dev=rblt24-10;   ! Adds dev to tg as dcp x !Exdai:dev=rblt24-1010;                      ! In service for added dev !Blode:dev=rblt24-1010;                      ! Deblock added dev !Stdep:dev=rblt24-1010;                      ! Dev status !Rxapp:mo=rxotg-10;                           ! Verify added dev are on abis path !! Then reload radio with fault !

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Radio Transmission Transcoder and Rate Adaptor Faultrrtbi:dev=RTTGD-25,force;    !If there is a call on this device it will drop it !rrtbe:dev=RTTGD-25;    !Unblock the transcoder device !  !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

SEIZURE SUPERVISION OF DEVICES IN BSC (BSC)

RASAP;RAPTI:DEV=…; “” :LCH=…; Trace of faulty devices …“CALL PATH TRACING" “” :CIC=…;RASAR:DETY=RALT;RASSP:DETY=RALT;

*******************************************************************************************************SEIZURE SUPERVISION OF LOGICAL CHANNELS

RLVAP; Print out os seizure supervision of alarm object channelRLVLP:CELL=…+sec; Printout of supervision dataRLVAR:CHTYPE=…; BUSY or IDLE

TRAPOOL CAPACITY OF THE BSC

RRTPP:TRAPOOL=ALL;

....................................................................................................................................................................................

CELL LOGICAL CHANNELS SEIZURE SUPERVISION (BSC)

RLVAP; Print out the TS´s that have not been used during long time in per cell basis.RLVLP; Print the values of seizure supervision, para TCH y SDCCHRLMSP; Checks if the TS is out of service.RLCRP:CELL=…; Shows the state of all the TS´s in the cellRLVLP:CELL=…; Print the values off seizure supervision, para TCH y SDCCHRLVLC:CELL=…,CHTYPE=…; Change the supervision parametersRLVAR:CHTYPE=..TCH..; Reset the buffer that contains the alarm parameterRLVLI:CELL=…,CHTYPE=…; Activates a seizure supervision for these channelsRAPTI:DEV= ou LCH= ou CIC=…; Initiates a tracing of the connections that use this DEV

CELL LOGICAL CHANNELS AVAILABILITY SUPERVISION (A2 OU A1) (BSC) A2/APT "NEBSC001HB00001" 340 070206   1849      CELL LOGICAL CHANNEL AVAILABILITY SUPERVISIONCELL       SCTYPE   CHTYPE   CHRATE   SPVBS608B                           TCH           FR          1 First, we can check the whole sector for supervision data.  The above A2 alarm printout tells us the fault is on a full rate TCH (traffic channel) with an SPV value of 1. <rlslp:cell=bs608b;CELL SUPERVISION OF LOGICAL CHANNEL AVAILABILITY DATA CELL       SCTYPEBS608B ACTIVE     CHTYPE   CHRATE   SPV   LVA    ACL   NCHYES            BCCH                                               1   A1      1                   SDCCH                                             8   A2      8                   TCH                    FR       1              12   A2      6                   TCH                    FR       2                0   A3      6                   TCH                    FR       3                0   A3      6                   TCH                    HR       1               0   A3     12                   TCH                    HR       3               0   A3     12                   CBCH                                               0   A2      0END Anytime the LVA or (Limit Value for Availability)  is greater than the NCH (Number of Available channels) this alarm will be generated.  Otherwise we can reset the supervision. Rlsle:cell=bs608b; This will turn off supervision on a sector.  No new alarms will be generated. Rlsli:cell=bs608b; Supervision will be turned back on.  Again, this is only a temporary fix if the LVA value is set too high.  The switch will be able to change the LVA to prevent it from alarming in the future.

RXTCP:MOTY=RXOTG,CELL=...; Prints the TG number and the channel groups linkedt to it RXCDP:MO= -...; Shows the MO configuration.

In the case TRX or RX, were blocked then all the associated TS´s are blocked as well,. The order of blocking the MOs is: TG, TF, TRX, RX, TX, TS.

RXMSP:MO=....; Print info on the state of the MORXBLI:MO=....; Block the MO (Managed Object)RXLTI:MO=....; Inicia un Loop test to verify the connection between the BSC and the TS of the BTSRXTEI:MO=....; Test MO's RXBLE:MO=....; Deblock MOs

- When the blocked TS´s are unknown:

RLSLP:CELL=...; See if the cell is down or not and how many TCH´s are out of serviceRLCRP:CELL=...; Shows the traffic in the cell. Check the BPC numbers wich are BLOCKRXCDP:MO=RX[E/O]TS-...; Print the TS's and their matching BPCsRXBLI:MO=....,FORCE; Block the TS´sRXBLI:MO=xx, SUBORD;RXESE:MO=RXOxx;SUBORD;RXESE:MO=RXOxx;SUBORD;RXBLE:MO=....; Desblock the TS´s

- Some times the cell does not comes upp, then HALT & UNHALT the cell:RLSTC:CELL=...[+ sector],STATE=HALTED; Put the cell out of servoice.RLSTC:CELL=...[+ sector],STATE=ACTIVE; Put the cell in service.- Some times the alarm does not desappear even if the cell comes upp, then do:

RLSLE:CELL= …;RLSLI:CELL= ….;

*******************************************************************************************************CELL RESTRICTION ACTIVATED (BSC)(To see wich cell is HALTED)

RLSTP:CELL = …ALL…, STATE = …HALTED…; Prints out all BTS´s wich are HaltedRLSTP:CELL=ALL; Prints out all cells in the BSC and their current stateRLCRP:CELL=...[+ sector]; Give us the occupation of channels.RLSTC:CELL=...[+ sector],STATE=HALTED; Put the cell out of servoice.RLSTC:CELL=...[+ sector],STATE=ACTIVE; Put the cell in service.

NOTA: Se houver mexidas nos combiners, seguir procedimento. Ter em atenção o hyb. Ficheiros: comb2.txt, comb3.txt

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

FREQUENCY HOPPING

- How to check frequecy hopping and how to make it OFF/ON if requested

RLCRP:CELL=… + sec;RLCHC:CELL=… + sec,HOP=OFF;RLCHC:CELL=… + sec,HOP=TCH;RLCPP:CELL=…;RLCLP:CELL=…;RXTCP:MOTY=RX[E/O]TG,CELL=... + sec; RXCDP:MO=RX[E/O]TG-...;

SLEEPING CELL

RLCFP:CELL=…;RLCRP:CELL=…;

: END;RLSTC:CELL=…,STATE=HALTED; Halt it RLSTC:CELL=…,STATE=ACTIVE; Activate it!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Activate & Halt Sectorsrlstp:cell=wdc081c;rlstc:cell=wan156a,state=halted;rlstc:cell=wan156a,state=active; !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Check if site is LIVE

Rlsbp:cell=abc001a;                           ! If CB=YES site is NOT live (Cell Barred) ! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

RF Loop Test FaultRxbli:mo=rxotrx-0-0;                           ! Block affected radio !Rxese:mo=rxotrx-0-0;                         ! Take out of service !Rxesi:mo=rxotrx-0-0                           ! Bring into service !Rxlti:mo=rxots-0-0-0                           ! Runs loop test, any FAIL fops needs to replace radio !Rxble:mo=rxotrx-0-0;                          ! Deblock radio, should be fine !

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

EDGErlbdc:cell=nj8041a,numreqegprsbpc=0,chgr=0;  ! Deactivate EDGE !rlbdc:cell=nj8041a,numreqegprsbpc=4,chgr=0;   !Activate EDGE !rlbdp:cell=nj8041a;    ! Status EDGE !

 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!MO Status BLL Blocked due to loadingBLT Blocked due to testingMBL Manually blockedBLO Automatically blockedBLA Blocked due to Activity Needed

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

RBS Related CommandsRLSLP:CELL=ZND890C; !Check availability of Logical channelsRXTCP:MOTY=RXOTG,CELL=ZND908A; !GET TG NUMBERRXCDP:MO=RXOTG-82; !Get configuration of TGwhen the site down CHECK ALL THESE (TG)===(CF)===(RXOIS)===(RXODP)===(RXOCON)===(TF)===(TRX)===(TX)===(RX)===(TS)=RXMFP:MO=RXOCF-107; !Get fault information of TG!RXMSP:MO=RXOTG-; !Check MO statusRXBLI:MO=RXOCF-59,SUBORD,FORCE; !Block MORXBLE:MO=RXOCF-59,SUBORD; !Deblock MORXESE:MO=RXOCF-166,SUBORD; !Take MO out of serviceRXESI:MO=RXOCF-331,SUBORD; !Bring MO into service

RXBLI:MO=RXOTRX-331-4,SUBORD,FORCE;RXBLE:MO=RXOTRX-331-4,SUBORD;RXESE:MO=RXOTRX-331-4,SUBORD;RXESI:MO=RXOTRX-331-4,SUBORD;

===============TO KNOW THE DIP FROM TGRXAPP:MO=RXOTG-82;RADEP:DEV=RBLT-1500;NTCOP:SNT=;DTQUP:DIP=RBLT46;=============IF YOU WANT TO CHECK THE SOFTWAREOF LINK WITHOUT RXOTG"((JUST NUM OF TG))"DTSTP:DIP=0ODP;===========TO BLOCKDTBLI:DIP=RBLT71;DTBLE:DIP=RBLT71;

============TO KNOW THE QUALITY OF LINK (SLIP2)MUST BE 0DTQUP:DIP=RBLT46;============TO REST LINKDTQSR:DIP=RBLT46,ES;DTQSR:DIP=RBLT46,ES2;DTQSR:DIP=RBLT46,SES;DTQSR:DIP=RBLT46,SES2;DTQSR:DIP=RBLT46,SF,DEGR;DTQSR:DIP=RBLT46,DF;============TO KNOW THE SITE BELONG TO DIPDTDIP:DIP=;NTCOP:SNT=;STDEP:DEV=;RXMDP:MOTY=RXOTG,DEV=;RXTCP:MO=RXOTG-;

====================NEBOR CELLRLNCP:CELL=ALL;================ TO TEST COMMUNICATION FOR BTS, YOU MUST BLOCK(RXBLI)RXTEI:MO=RXOTG-;================ TO KNOW THE HIOSTORY&RESETRXELP:MO=RXOTG-;RXELR:MO=RXOTG-;================ TO INSTALL FROM BSCRXPLI:MO=RXOTG-:================ FOR HALTED & ACTIVE SITERLSTP:CELL=;RLSTC:CELL=,STATAS=HALTED;================ TO KNOW FREQUNCYRLCFP:CELL;================ FOR HOPPINGRLCHP:CELL;RLCHC:CELL=UND162A,HOP=OFF,CHGR=1;=============== TO KNOW CGI THE LAST 5 DIGT IN ID NUMRLDEP:CELL=;=============== TO KNOW INF ABOUT IDEL & BUSY TCH OR BCCH OR SDCCHRLCRP:CELL=;

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Miscellaneous Cell Admin CommandsRlbdc:cell=abc123a,numreqbpc=8;                ! Reset bpcfail on timeslots !Rlstp:cell=all,state=active;                 ! Print all active cells !Rlstp:cell=all,state=halted;                               ! Print all halted cells !Rldep:cell=abc123a;                          ! Print cell description data !Rlnrp:cell=abc123a,cellr=all;            ! List external neighbor cells !Rlncp:cell=abc123a;                           ! To internal neighbor cells !Rlcpp:cell=abc123a;                           ! Cell power data print !Rlcfp:cell=abc123a;                            ! Radio Frequencies !Rldgp:cell=all;                                      ! Prints cell chgr data !Rllap:lai=310-27-40540;                    ! Prints cells in LAI !Rrmar:trapool=all;                                              ! Reset trapool !Rxpli:mo=rxocf-10,uc;                        ! Load software to CF !Rlsli:cell=abc123a,sctype=(ul/ol);    ! Logical chan supervision init !Rxhdp:mo=rxots-13-0-0&&-7;           ! Maps MAIO to TS !Rlbdp:cell=wan010a;                         ! Defined Logical Channels !Rlslp:cell=wan036a;                           ! Number of Logical Channels available !                       Rldep:cell=wan010a;                         ! Description Data !Rlcfp:cell=wan010a;                           ! Frequencies on site !Rlchp:cell=wan010a;                          ! Channel Groups and MAIOs !Rlnrp:cell=wan010a,cellr=wan010b;              ! Neighbor relation parameters !Rlnrp:cell=wan010a,cellr=all;           ! All Neighbor relations !

Rxelp:mo=rxotg-13;                            ! Error Log !Rxhdp:mo=rxots-13-0-0&&-7;           ! Maps MAIO to TS !Rlbdp:cell=wan010a;                         ! Defined Logical Channels !Rlslp:cell=wan036a;                           ! Number of Logical Channels available !                       Rldep:cell=wan010a;                         ! Description Data !Rlcfp:cell=wan010a;                           ! Frequencies on site !Rlchp:cell=wan010a;                          ! Channel Groups and MAIOs !Rlnrp:cell=wan010a,cellr=wan010b;              ! Neighbor relation parameters !Rlnrp:cell=wan010a,cellr=all;           ! All Neighbor relations !Rlsbp:cell=wdc018c;                          ! Cell Barred !