bldtec3 wall covering materials
TRANSCRIPT
FANER x SURIO
WALL COVERING MATERIALS
#MS-89 FOLKSTONE TEXTURED
ELASTOMETRIC PAINT FINISH
ELASTOMETRIC WALL COATINGS ARE EXTERIOR ACRYLIC LATEX MASONRY PAINTS DESIGNED TO BE APPLIED IN VERY THICK FILMS (ABOUT 10 TIMES AS THICK AS REGULAR PAINTS); THEY ARE TOUGH AND FLEXIBLE, AND STRETCH AS CRACKS UNDERNEATH OPEN AND CLOSE, THUS BRIDGING THE CRACKS AND KEEPING WATER OUT WHILE MAINTAINING A NICE APPEARANCE. THESE COATINGS ARE CALLED EWCs FOR SHORT. THEY CAN BE TINTED TO A LIGHT COLOR.
SPECIFICATIONS
FINISH: SHEEN
COLOR: #MS-89 FOLKSTONE
PRACTICAL COVERAGE: 20-25 m2 per 4L per coat depending on surface porosity
APPLICATION: BRUSH, ROLLER, SPRAY
DRYING TIME: DRIES IN 2 TO 3 HOURS
PAINTING INTERVAL: 2-4 HOURS
REDUCTION: REDUCE WITH NOT MORE THAN ¼ LITER OF WATER PER 4L PAINT
THINNING/CLEANING: WATER
•Ideal for exterior vertical concrete and masonry walls•Flexible high-build coating, bridges hairline cracks and can stretch up to 600%•Durable low sheen finish•Alkali, mildew and dirt resistant finish (ideal for new or weathered stucco)•Covers up to 125 sq. ft. per gallon•Withstands 98 mph wind-driven rain•Easy clean-up with soap and water•100% acrylic latex
1.Remove all dirt, mildew and chalk; treat mildew with a 3:1 water:bleach solution, leaving on for 20 minutes, then rinse thoroughly; careful power washing with plain water (no cleaning agent or bleach added), being sure to not drive water into any openings there may be in the existing coating.
2.Seal all cracks and openings, using a quality acrylic or siliconized acrylic caulk. Do not use silicone caulk.
3.Check entire elastomeric surface for blistering or other adhesion loss: A) carefully remove any blistering or failing coating; seal the edge of the surrounding remaining coating with a
quality acrylic latex caulk; apply a water-based or solvent-based clear masonry sealer to the masonry surface thus exposed; then apply an elastomeric coating to the repaired area, overlapping it and feathering, onto the remaining elastomeric.
B) identify any source of intruding water or moisture that may have caused the blistering or other adhesion loss, and eliminate it.
1.Apply a top quality exterior 100% acrylic latex house paint in a flat, satin or semigloss finish, that is recommended by the manufacturer for application over existing elastomeric coatings. It is important that steps be taken to minimize chance of cracking of the new paint as applied over the elastomeric: A) the paint must be of high quality, meaning, for example, that with flat paints, excessive extenders should not
be used, that appropriate mildewcide is included, that an appropriate binder is employed, etc.; therefore, the manufacturer's top line product should be specified.
B) The paint must be applied under moderate weather conditions: applying below the recommended minimum application temperature can result in serious cracking; it is preferable that the air temperature be at or above the minimum recommended application temperature for at least the following 24 hours.
C) The paint must be applied at sufficient thickness. In general, a dry paint film of 1.5 mils per coat is appropriate; two coats will provide ample crack resistance. Pre-thinning of the paint will reduce the solids content by volume, and additional wet paint film thickness has to be applied to compensate, so pre-thinning should be discouraged.
D) There is always the chance that some cracking of the new paint will occur at some point, so it can be helpful to utilize a color similar to that of the existing elastomeric coating to minimize show-through.
GUIDELINES FOR PAINTING BUILDINGS DONE PREVIOUSLY WITH AN ELASTOMERIC
ULTRA PURE WHITE ENAMEL EXTERIOR
PAINT SEMI-GLOSS FINISHExterior Semi-Gloss Enamel is 100%
acrylic, provides a Mildew resistant finish and is formulated to withstand wear. This finish resists moisture, fading and stains; provides ultimate durability, Exceptional hide and a radiant sleek appearance.
Usage Summary
2 HR Dry Time 4 HR Recoat Time
250-400 Sq. Ft Coverage per Gallon
Soap & WaterClean-Up
Protectfrom Freezing
DETAIILS
•Countersink nailheads, fill and sand smooth. Remove rust, loose or peeling paint. Repair imperfections and sand smooth.•Wash off dirt, grease and chalk with detergent and/or power wash. Remove mildew stains with a mildew stain removing product.•Clean and sand new or weathered wood. Scuff sand or degloss smooth or glossy surfaces.•Scuff sand or etch metals. Rinse and allow to dry.•Caulk windows, doors and other openings. Allow new stucco, plaster and masonry to cure for 30 days before painting.•Use a primer for repaired or uncoated surfaces, including woods that contain tannins (two primer coats required for redwood and cedar) and heavily stained areas.•Lock in stains with the first primer coat; if necessary, apply a second primer coat.•For drastic color changes or when applying deep colors denoted with a dagger on the color chip, apply a tinted primer coat if needed.
Preparation & Prime
•Apply product on dry substrates when air and surface temperatures are between 35°-90°F (2°-32°C) and will remain between 35°-90°F (2°-32°C) for at least 4 hours after applying.•Do not paint when rain or heavy condensation is expected.•Stir paint occasionally. Intermix containers of same product to ensure color and sheen uniformity.•On semi-smooth surfaces, use a high quality 3/8-1/2” nap roller cover, nylon/polyester brush or an airless sprayer (.015-.021” spray tip, 60 mesh filter).•On rough surfaces, use a high quality 3/4-1” nap roller cover.•Do not thin if using a roller or brush; however, if using a sprayer and thinning is required, thin with water at a rate of no more than 1/2 pint per gallon.•Certain colors may require more than one coat for complete hide.•On heavy stains and woods that contain tannins, allow 12-16 hours of dry time between coats. Cooler temperatures or higher humidity may prolong drying time.•After 4 weeks, cured paint film may be cleaned with a mild, non-abrasive liquid detergent.•Dry paint film is mildew resistant.•When applying to vinyl, color choice must be the same color or lighter than the existing color. Do not use on floors.
Application
50 x 100 mm TUBULAR
ALUMINUM LOUVERS (POWDER COATED SUPER DURABLE:
VERIFY COLOR)
Wall LouversLouvers for wall installation. In selecting wall louvers and vents, consideration for your application is critical to your project success. Louvers are designed to allow air into the building while keeping out unwanted elements.
Wall Louvers - Types and Depths
GROOVE
50mm GROOVETHE TRADITIONAL WAY OF CREATING GROOVE JOINT ON WALL IS BY USING WOOD INSERT PLASTERED ON THE SAME TIME THEN REMOVED THE WOOD AFTER CONCRETE DRIES.
ANOTHER OPTION IS BY PLASTERING THE WALL AND SCRAPING THE GROOVE WHILE THE CONCRETE IS STILL SOFT.
GROOVE JOINT
INSTALLED AND
PLASTERED
GROOVE JOINT AFTER
PLASTERING
BENZOTRIALE – AN ULTRAVIOLET
(UV) LIGHT RESISTANCE
CHEMICAL ADDITIVE WHICH
HAS BEEN ADDED IN OUR GROOVE
JOINT PRODUCTS, THUS ITS PHYSICAL
PROPERTIES AND COLOUR ARE NOT
AFFECTED BY EXPOSURE OF UV LIGHT FROM THE
SUN
SPECIFICATIONSSIZE: 50 MM X 13.5 MMLENGTH: 2 METERSPACKING: 20 PCS PER BAGCOLOR: WHITE
PVC GROOVE JOINT ABLE TO FORM FEATURE GROOVE LINES IN PLASTERED WALLS AND IMPROVES THE QUALITY OF PLASTERED WALLS AND REDUCES INCONSISTENCIES DUE TO WORKMANSHIP
FANER x SURIO
FLOOR COVERING MATERIALS
1. (Fire Exit, Receiving Lobby, Baggage Storage, Electrical Room, Smoke LobbyConcrete Floor with 4 coats of Clear Semi-Gloss Polyurethane Model #13021 @ 18.9kg/m^2 resistance
2. (Female and Male Bathroom, T&B)
0.15m x 0.60m Montagne Dapple Gray Matte Porcelain Floor Tile Model #ULM7
3. (Lounge)
9mm Thick, 1m x 3.66m Nourtex/ Natural Harmony Soleil Velvet Carpet Model #120533
4. (Lobby, Elevator Lobby)
10mm Thick, 0.3m x 0.9m Madeira Natural Cork Flooring Model #HL9308MN with 2 coats of Clear Gloss Oil-Based Interior Polyurethane Model #130512 @ 18.9kg/m^2 resistance
5. (Manager's Office, Staff’s Office)
0.15m x 0.9m Autumn Oak Resilient Vinyl Plank Flooring Model #54212 with 2 coats of Clear Satin Water-Based Floor Polyurethane Model #230231 @ 18.9kg/m^2 resistance
6. (Kitchen, Kitchen Storage, Cafeteria)0.15m x 0.9m Dark Walnut Resilient Vinyl Plank Flooring Model #60915 with Clear Matte Soft Touch Polyurethane Model #266233 @ 18.9kg/m^2 resistance