Appendices

Appendix 1

LIST OF IRC PUBLICATIONS REFERRED TO IN THE SPECIFICATIONS

Number Designation Title

IRC:2-1968 Route Marker Signs for National Highways (First Revision)

IRC:5-1998 Standard Specifications and Code of Practice for RoadBridges, Section I – General Features of Design

(Seventh Revision)

IRC:6-2000 Standard Specifications and Code of Practice for RoadBridges, Section II – Loads and Stresses (Fourth

Revision)

IRC:8-1980 Type Designs for Highway Kilometre Stones (Second Revision)

IRC:10-1961 Recommended Practice for Borrowpits for RoadEmbankments Constructed by Manual Operation

IRC:12-2009 Guidelines for Access, Location and Layout of RoadsideFuel Stations and Service Stations (Third Revision)

IRC:14-2004 Recommended Practice for Open Graded PremixCarpets (Third Revision)

IRC:16-2008 Standard Specifications and Code of Practice for Primeand Tack Coat (Second Revision)

IRC:17-1965 Tentative Specification for Single Coat BituminousSurface Dressing

IRC:18-2000 Design Criteria for Prestressed Concrete Road Bridges(Post-Tensioned Concrete) (Third Revision)

IRC:19-2005 Standard Specification and Code of Practice for WaterBound Macadam (Third Revision)

IRC:20-1966 Recommended Practice for Bituminous PenetrationMacadam (Full Grout)

IRC:21-2000 Standard Specifications and Code of Practice for RoadBridges, Section III – Cement Concrete (Plain andReinforced) (Third Revision)

IRC:22-2008 Standard Specifications and Code of Practice for RoadBridges, Section VI – Composite Construction (LimitStates Design) (Second Revision)

IRC:23-1966 Tentative Specification for Two Coat Bituminous Surface Dressing

IRC:24-2001 Standard Specifications and Code of Practice for RoadBridges, Section V – Steel Road Bridges (Second Revision)

2

Number Designation Title

IRC:25-1967 Type Designs for Boundary Stones

IRC:26-1967 Type Design for 200-Metre Stones

IRC:27-2009 Specifications for Bituminous Macadam(First Revision)

IRC:29-1988 Specification for Bituminous Concrete (Asphaltic Concrete)

for Road Pavement (First Revision)

IRC:30-1968 Standard Letters and Numerals of Different Heights forUse on Highway Signs

IRC:35-1997 Code of Practice for Road Markings (with Paints)

(First Revision)

IRC:36-1970 Recommended Practice for Construction of EarthEmbankments for Road Works

IRC:37-2001 Guidelines for the Design of Flexible Pavements(Second Revision)

IRC:40-2002 Standard Specifications and Code of Practice for RoadBridges, Section IV – (Brick, Stone and Block Masonry)(Second Revision)

IRC:45-1972 Recommendations for Estimating the Resistance ofSoil Below the Maximum Scour Level in the Design ofWell Foundations of Bridges

IRC:47-1972 Tentative Specification for Built-up Spray Grout

IRC:48-1972 Tentative Specification for Bituminous SurfaceDressing Using Precoated Aggregates

IRC:50-1973 Recommended Design Criteria for the Use of CementModified Soil in Road Construction

IRC:51-1992 Guidelines for the Use of Soil Lime Mixes in RoadConstruction (First Revision)

IRC:56-1974 Recommended Practice for Treatment of EmbankmentSlopes for Erosion Control

IRC:63-1976 Tentative Guidelines for the Use of Low Grade Aggregates andSoil Aggregates Mixtures in Road Pavement Construction

IRC:67-2001 Code of Practice for Road Signs (First Revision)

IRC:72-1978 Recommended Practice for Use and Upkeep of Equipment, Toolsand Appliances for Bituminous Pavement Construction

IRC:75-1979 Guidelines for the Design of High Embankments

3

Number Designation Title

IRC:78-2000 Standard Specifications and Code of Practice for Road Bridges,Section VII – Foundations and Substructure (Second Revision)

IRC:79-1981 Recommended Practice for Road Delineators

IRC:82-1982 Code of Practice for Maintenance of BituminousSurfaces of Highways

IRC:83-1999(Part-I) Standard Specifications and Code of Practice for RoadBridges, Section IX – Bearings, Part I : Metallic Bearings(First Revision)

IRC:83-1987(Part II) Standard Specifications and Code of Practice for RoadBridges, Section IX – Bearings, Part II: Elastomeric Bearings

IRC:87-1984 Guidelines for the Design and Erection of Falsework forRoad Bridges

IRC:89-1997 Guidelines for Design and Construction of River Training& Control Works for Road Bridges (First Revision)

IRC:90-1985 Guidelines of Selection, Operation and Maintenance ofBituminous Hot Mix Plant

IRC:93-1985 Guidelines on Design and Installation of Road Traffic Signals

IRC:111-2009 Specifications for Dense Graded Bituminous Mixes

IRC:SP:11-1984 Handbook of Quality Control for Construction of Roadsand Runways (Second Revision)

IRC:SP:21-2009 Guidelines for Landscaping and Tree Plantation (First Revision)

IRC:SP:30-2009 Manual on Economic Evaluation of Highway Projects in India(Second Revision)

IRC:SP:31-1992 New Traffic Signs

IRC:SP:53-2002 Guidelines on Use of Polymer and Rubber Modified Bitumen inRoad Construction (First Revision)

IRC:SP:55-2001 Guidelines for Safety in Construction Zones

IRC:SP:58-2001 Guidelines for Use of Flyash in Road Embankments

IRC:SP:59-2002 Guidelines for Use of Geotextiles in Road Pavements andAssociated Works

IRC:SP:60-2002 An Approach Document for Assessment of RemainingLife of Concrete Bridges

IRC:SP:61-2004 An Approach Document on Whole Life Costing for Bridges in India

4

Number Designation Title

IRC:SP:62-2004 Guidelines for the Design and Construction of Cement ConcretePavement for Rural Roads

IRC:SP:63-2004 Guidelines for the Use of Interlocking Concrete Block Pavement

IRC:SP:64-2005 Guidelines for the Analysis and Design of Cast-in-Place VoidedSlab Superstructure

IRC:SP:65-2005 Guidelines for Design and Construction of Segmental Bridges

IRC:SP:66-2005 Guidelines for Design of Continuous Bridges

IRC:SP:67-2005 Guidelines for Use of External and Unbonded PrestressingTendons in Bridge Structures

IRC:SP:68-2005 Guidelines for Construction of Roller Compacted ConcretePavements

IRC:SP:69-2005 Guidelines & Specifications for Expansion Joints

IRC:SP:70-2005 Guidelines for the Use of High Performance Concrete in Bridges

IRC:SP:71-2006 Guidelines for Design and Construction of Pretensioned Griderof Bridges

IRC:SP:74-2007 Guidelines for Repair and Rehabilitation of Steel Bridges

IRC:SP:75-2008 Guidelines for Retrofitting of Steel Bridges by Prestressing

IRC:SP:76-2008 Tentative Guidelines for Conventional, Thin and Ultra ThinWhitetopping

IRC:SP:78-2008 Specifications for Mix Seal Surfacing (MSS) Close-GradedPremix Surfacing (CGPS)

IRC:SP:79-2008 Tentative Specifications for Stone Matrix Asphalt

IRC:SP:80-2008 Guidelines for Corrosion Prevention, Monitoring and RemedialMeasures for Concrete Bridge Structures

IRC:SP:81-2008 Tentative Specification for Slurry Seal and Microsurfacing

IRC:SP:83-2008 Guidelines for Maintenance, Repairs & Rehabilitation of CementConcrete Pavements Ministry of Shipping & Transport (Roads Wing)Handbook on Road Construction Machinery

HRB SR.No.11, 1992 State of the Art: Granular and Bound Bases and Sub-Bases

5

Appendix-2

LIST OF INDIAN AND FOREIGN STANDARDS REFERRED TO IN THESPECIFICATIONS

Number Designation Title

(A) INDIAN STANDARDSIS:5-2004 Colour for ready mixed paints and enamels (Fifth revision)

IS:73-2006 Viscosity Grade Bitumen Specifications

IS:164-1981 Ready mixed paints, brushing, for road marking, to IndianStandard Colour No.356 Golden yellow, white and black

IS:210-1993 Grey iron castings (fourth revision)

IS:215-1995 Road tar specification (third revision)

IS:217-1988 Specification for Cutback Bitumen (second revision)

IS:269-1989 Specification for 33 grade ordinary Portland cement(fourth revision)

IS:278-1978 Specification for Galvanized steel barbed wire for fencing(third revision)

IS:280-2006 Specification for Mild steel wire for general engineeringpurposes (fourth revision)

IS:334-2002 Glossary of terms relating to bitumen and tar (third revision)

IS:383-1970 Specification for Coarse and fine aggregates from naturalsources for concrete (second revision)

IS:432-1982 Mild steel and medium tensile steel bars and hard-drawnsteel wire for concrete reinforcement

Part I Specification for Mild steel and medium tensile steel bars(third revision)

Part II Hard-drawn steel wire (third revision)

IS:443-1975 Methods of sampling and test for rubber hoses

(second revision)

IS:454-1994 Specification for Cutback bitumen from Waxy Crude-Specification (second revision)

IS:455-1989 Specification for Portland stag cement (fourth revision)

IS:456-2000 Plain and reinforced concrete – Code of Practice(Fourth revision)

6

Number Designation Title

IS:458-2003 Precast Concrete pipes (with and withoutreinforcement) – specification (third revision)

IS:460-1985 Specification for test sieves:

IS:508-1987 Specification grease graphited (fourth revision)

IS:516-1959 Methods of test for strength of concrete

IS:702-1988 Industrial bitumen (second revision)

IS:736-1986 Wrought aluminium and aluminium alloys, plates for generalengineering purposes (third revision)

IS:814-2004 Covered electrodes for manual metal arc welding ofcarbon and carbon manganese steel (sixth revision)

IS:1030-1998 Carbon steel castings for general engineering purposes(fifth revision)

IS:1077-1992 Common burnt clay building bricks (fifth revision)

IS:1124-1974 Method of test for water absorption apparent specificgravity and porosity of natural building stones (first revision)

IS:1129-1972 Dressing of natural building stones (first revision)

IS:1148-1982 Hot rolled rivet bars (upto 40 mm dia) for structuralpurposes (third revision)

IS:1149-1982 High tensile rivet bars for structural purposes (third revision)

IS:1195-2002 Bitumen mastic for flowing (second revision)

IS:1199-1959 Method of sampling and analysis of concrete

IS:1201:1978 Sampling – (see IS:1201 to IS:1220)

IS:1203-1978 Determination of penetration (first revision) (see IS:1201 toIS:1220)

IS:1205-1978 Determination of softening point (first revision) (see IS:1201to IS:1220)

IS:1206 : Part 1 : 1978 Determination of viscosity: Part 1 Industrial viscosity - (seeIS 1201 to IS 1220)

IS:1206 : Part 2 : 1978 Determination of viscosity: Part 2 Absolute viscosity - (seeIS 1201 to IS 1220)

IS:1206 : Part 3 : 1978 Determination of viscosity: Part 3 Kinematic viscosity - (seeIS 1201 to IS 1220)

7

Number Designation Title

IS:1208-1978 Determination of ductility (first revision) (see IS:1201 toIS:1220)

IS:1209-1978 Determination of flast point and fire point (first revision)(see IS:1201 to IS:1220)

IS:1212-1978 Determination of loss on heating (first revision)

IS:1216-1978 Determination of solubility in carbon disulphidetrichoroethylene (first revision)

IS:1217-1978 Determination of mineral matter ash) (first revision)

(see IS:1201 to IS:1220)

IS 1239 : Part 1 : 2004 Steel Tubes, Tubulars and Other Wrought Steel Fittings -Specification - Part 1 : Steel Tubes

IS 1239 : Part 2 : 1992 Mild steel tubes, tubulars and other wrought steel fittings,Part 2 Mild steel tubulars and other wrought steel pipe fittings

IS 1364 : Part 1 : 2002 Hexagon Head Bolts, Screws and Nuts of ProductGrades A and B - Part 1 : Hexagon Head Bolts (SizeRange M 1.6 to M 64)

IS 1364 : Part 2 : 2002 Hexagon Head Bolts, Screws and Nuts of Product GradesA and B - Part 2 : Hexagon Head Screws (Size RangeM 1.6 to M 64)

IS 1364 : Part 3 : 2002 Hexagon Head Bolts, Screws and Nuts of Product GradesA and B - Part 3 : Hexagon Nuts, Style 1 (Size Range M 1.6to M 64)

IS 1364 : Part 4 : 2003 Hexagon Head Bolts, Screws and Nuts of Product GradesA and B - Part 4 : Hexagon Thin Nuts (Chamfered) (SizeRange M1.6 to M64)

IS 1364 : Part 5 : 2002 Hexagon Head Bolts, Screws and Nuts of Product GradesA and B - Part 5 : Hexagon Thin Nuts - Product Grade B(Unchamfered) (Size Range M 1.6 to M 10)

IS 1364 : Part 6 : 2002 Hexagon Head Bolts, Screws and Nuts of Product GradesA and B - Part 6 : Hexagon Nuts, Style 2

IS 1367 : 2002 (Part 1 to 20) Technical Supply Conditions for ThreadedSteel Fasteners

IS:1387-1993 General requirements for the supply of metallurgicalmaterials (second revision)

8

Number Designation Title

IS:1398-1982 Packing paper, waterproof, bitumen-laminated(second revision)

IS: 1448 (Part 1 to 152) Methods of Test for Petroleum and its Products

IS:1477 Code of practice for painting of ferrous metals in buildings

Part 1-1971 Pretreatment (first revision)

Part 2-1971 Painting (first revision)

IS:1489-1991 Specification for Portland-pozzolana cement

Part 1 Flyash based (third revision)

Part 2 Calcined clay based (third revision)

IS:1498-1970 Classification and identification of soils for generalengineering purposes (first revision)

IS:1514-1990 Methods of sampling and test for quick lime and hydratedlime (first revision)

IS:1732-1989 Dimensions for round and square steel bars for structuraland general engineering purposes (second revision0

IS:1785-1983 Plain hard-drawn steel wire for prestressed concrete

Part I Cold-draws stress relieved wire (second revision)

Part II As drawn wire

IS:1786-1985 High strength deformed steel bars and wires for concretereinforcement (third revision)

IS 1838 : Part 1 : 1983 Specification for preformed fillers for expansion joint inpavements and structures (non extruding and resilient type):Part 1 Bitumen impregnated fibre

IS 1838 : Part 2 : 1984 Specification for preformed fillers for expansion joint inpavements and structures (non extruding and resilient type)Part 2 CNSL Aldehyde resin and coconut pith

IS:1888-1982 Method of load tests on soils (second revision)

IS:2004-1991 Carbon steel forging for general engineering purposes(third revision)

IS:2062-2006 Steel to general structural purpose (fifth revision)

IS:2116-1980 Sand for masonry mortars (first revision)

IS:2131-1981 Methods for standard penetration test for soils(first revision)

9

Number Designation Title

IS:2250-1981 Code of practice for preparation and use of masonrymortars (first revision)

IS:2386-1963 Methods of test for aggregates for concrete

Part 1 Particle size and shape

Part 2 Estimation of deleterious materials and organic impurities

Part 3 Specific gravity, density, voids, absorption and bulking

Part 4 Mechanical properties

Part 5 Soundness

Part 6 Measuring mortar making properties of fine aggregates

Part 7 Alkali – aggregate reactivity

Part 8 Petrographic examination

IS:2720 Methods of test for soils

Part 2-1973 Determination of water content (second revision)

Part 3-1980 Determination of specific gravity (first revision)

Section I Fine grained soils

Section II Medium and coarse grained soils

Part 4-1985 Grain size analysis (second revision)

Part 5-1985 Determination of liquid and plastic limits (second revision)

Part 7-1980 Determination of moisture content/dry density relation usinglight compaction (second revision)

Part 8-1983 Determination of water content-dry density relation usingheavy compaction (second revision)

Part 10-1991 Determination of unconfined compressive strength (secondrevision0

Part 13-1986 Direct shear test (second revision)

Part 14-1983 Determination of density index (relative density ofcohesionless soils (first revision)

Part 16-1987 Laboratory determination of CBR (second revision)

Part 27-1977 Determination of total soluble sulphates (first revision)

Part 28-1974 Determination of dry density of soils in-place by the sandreplacement method (first revision)

10

Number Designation Title

Part 29-1975 Determination of dry density of soils in-place by core cuttermethod (first revision0

Part 37-1976 Determination of sand equivalent values of soils and fineaggregates

Part 40-1977 Determination of free swell index of soils

IS 3117 : 2004 Bitumen Emulsion for Roads and Allied Applications(Anionic Type) - Specification

IS:3466-1988 Specification for Masonry cement (second revision)

IS:3764-1992 Code of safety for excavation work (first revision)

IS:4138-1977 Safety code for working in compressed air (first revision)

IS:4332 Method of test for stabilized soils

Part I-1967 Methods of sampling and preparation of stabilized soils fortesting

Part 3-1967 Test for determination of moisture content-dry densityrelation for stabilized soil mixtures

Part 4-1968 Wetting and drying and, freezing and thawing tests forcompacted soil-cement mixtures

Part 5-1970 Determination of unconfined compressive strength ofstabilized soil

Part 7-1973 Determination of cement content of cement stabilized soils

Part 8-1969 Determination of lime content of lime stabilized soils

IS:4434-1978 Code of practice for in-situ vane shear test for soils

(first revision)

IS:4826-1979 Hot dipped galvanized coating on round steel wires

(first revision)

IS:5317-2002 Pitch mastic for bridge decking and Roads -specifications

IS:5435-1987 General requirements for cold asphalt macadam mixingplants (first revision)

IS:5640-1970 Method for determining the aggregate impact value of softcoarse aggregate

IS:6006-1983 Uncoated stress relieved strands

11

Number Designation Title

IS:6241-1971 Methods of test for determination of stripping value of roadaggregates

IS:6909-1990 Supersulphated cement

IS:6925-1973 Methods of test for determination of water soluble chloridesin concrete admixtures

IS:7537-1974 Road traffic signals

IS:7623-1993 Specification for li thium base grease for industrialpurposes (second revision)

IS:8041-1990 Rapid hardening Portland cement (second revision)

IS:8112-1989 43 grade ordinary Portland cement (first revision)

IS:8500-1991 Structural steel – microalloyed (medium and high strengthqualities (first revision)

IS:8887-2004 Bitumen emulsion for roads (cationic type) –specification (second revision)

IS:9103-1999 Admixtures for concrete (first revision)

IS:9381-1979 Methods of testing tar and bituminous materials:determination of frass breaking point of bitumen

IS:9382-1979 Methods of testing tar and bituminous materials:determination of effect of heat and iar by thin film oven tests

IS:10262-2004 Guidelines for concrete mix design

IS:12269-1987 Specification for 53 grade ordinary Portland cement

IS:12330-1988 Specification for sulphate resisting Portland cement

IS:13321 (Part I)-1992 Glossary of terms for geosynthetics, part 1: terms used inmaterials and properties

IS:13325-1992 Determination of tensile properties of extruded polymergeogrids using the wide strip-test method

IS:13326 (Part I)-1992 Evaluation of interface friction between geosynthetics andsoil-method of test, part 1: modified direct shear technique

IS:SP 23-1982 Handbook on concrete mixes

(B) FOREIGN STANDARDS

ASTM D36 - 06 Standard Test Method for Softening Point of Bitumen(Ring-and-Ball Apparatus)

12

Number Designation Title

ASTM D395 - 03(2008) Standard Test Methods for Rubber Property—CompressionSet

ASTM D412 - 06ae2 Standard Test Methods for Vulcanized Rubber andThermoplastic Elastomers—Tension

ASTM D429 - 08 Standard Test Methods for Rubber Property—Adhesion toRigid Substrates

ASTM D573 - 04 Standard Test Method for Rubber—Deterioration in an

Air Oven

ASTM D624 - 00(2007) Standard Test Method for Tear Strength of ConventionalVulcanized Rubber and Thermoplastic Elastomers

ASTM D664 - 09 Standard Test Method for Acid Number of PetroleumProducts by Potentiometric Titration

ASTM D797-82(1989) Test Method for Rubber Property-Young’s Modulus atNormal and Subnormal Temperatures (Withdrawn 1994)Withdrawn Standard:

ASTM D977 - 05 Standard Specification for Emulsified Asphalt

ASTM D979 - 01(2006)e1 Standard Practice for Sampling Bituminous Paving Mixtures

ASTM D1075 - 07 Standard Test Method for Effect of Water on CompressiveStrength of Compacted Bituminous Mixtures

ASTM D1149 - 07 Standard Test Methods for Rubber Deterioration-Crackingin an Ozone Controlled Environment

ASTM D1559-89 Test Method for Resistance of Plastic Flow of BituminousMixtures Using Marshall Apparatus (Withdrawn 1998)Withdrawn Standard:

ASTM D2026 - 97(2004) Standard Specification for Cutback Asphalt(Slow-Curing Type)

ASTM D2027 - 97(2004) Standard Specification for Cutback Asphalt(Medium-Curing Type)

ASTM D2041 - 03a Standard Test Method for Theoretical Maximum SpecificGravity and Density of Bituminous Paving Mixtures

ASTM D2172 - 05 Standard Test Methods for Quantitative Extraction ofBitumen From Bituminous Paving Mixtures

ASTM D2240 - 05 Standard Test Method for Rubber Property—Durometer Hardness

13

Number Designation Title

ASTM D2397 - 05 Standard Specification for Cationic Emulsified Asphalt

ASTM D3203 - 05 Standard Test Method for Percent Air Voids in CompactedDense and Open Bituminous Paving Mixtures

ASTM D3625 - 96(2005) Standard Practice for Effect of Water on Bituminous-CoatedAggregate Using Boiling Water

ASTM D3910 - 07 Standard Practices for Design, Testing, and Construction ofSlurry Seal

ASTM D4533 - 04 Standard Test Method for Trapezoid Tearing Strength ofGeotextiles

ASTM D5976-96 Standard Specification for Type I Polymer Modified AsphaltCement for Use in Pavement Construction –SUPERSEDED

ASTM E11 - 04 Standard Specification for Wire Cloth and Sieves forTesting Purposes

ASTM E810 - 03(2008) Standard Test Method for Coefficient of Retroreflection ofRetroreflective Sheeting Utilizing the Coplanar Geometry

AASHTO : T283-07-UL Standard Method of Test for Resistance of Compacted HotMix Asphalt (HMA) to Moisture-Induced Damage, SingleUser Digital Publication

AASHTO : M294-08-UL Standard Specification for Corrugated Polyethylene Pipe,300- to 1500-mm Diameter, Single User Digital Publication

AASHTO :M288-06-UL Standard Specification for Geotextile Specification forHighway Applications, Single User Digital Publication

AASHTO :M017-07-UL Standard Specification for Mineral Filler forBituminous Paving Mixtures

AASHTO : R005-08-UL Standard Recommended Practice for Selection andUse of Emulsified Asphalts

AASHTO : M081-92-UL Standard Specification for Cutback Asphalt (Rapid-CuringType), Single User Digital Publication

AASHTO : M082-75 Standard Specification for Cut-back asphalt (Medium-curingtype)

AASHTO : M140-03-UL Standard Specification for Emulsified Asphalt

AASHTO : M57-80 Materials for embankments and subgrades

AASHTO : M147-65 Materials for aggregate and soil-aggregate sub-base, baseand surface courses

14

Number Designation Title

AASHTO : M216-05-UL Standard Specification for Lime for Soil Stabilization,Single User Digital Publication

AASHTO : M249-08-UL Standard Specification for White and Yellow ReflectiveThermoplastic Striping Material (Solid Form), SingleUser Digital Publication

AASHTO : M268-08-UL Standard Specification for Retroreflective Sheeting forTraffic Control

AASHTO : M282-99-UL Standard Specification for Joint Sealants, Hot-Poured,Elastomeric-Type, for Portland Cement ConcretePavements

AASHTO : M082-75-UL Standard Specification for Cutback Asphalt (Medium-CuringType), Single User Digital Publication

AASHTO : M140-03-UL Standard Specification for Emulsified Asphalt

AASHTO : M208-01-UL Standard Specification for Cationic Emulsified Asphalt,Single User Digital Publication

AASHTO : T182-84-UL Standard Method of Test for Coating and Stripping ofBitumen-Aggregate Mixtures

AASHTO : T283-07-UL Standard Method of Test for Resistance of Compacted HotMix Asphalt (HMA) to Moisture-Induced Damage, SingleUser Digital Publication

BS : 410-2005 Test sieves – Technical requirements and Testing

Part 1 Test sieves of metal wire cloth

Part 2 Test sieves of perforated Metal plate

BS : 434 Bitumen road emulsions (anionic and cationic)

Part 2 : 1984 Specification for bitumen road emulsion

Part 2:2006 Code of practice for the use of cationic bitumen emulsionson roads and other paved areas

BS : 598 Sampling and examination of bituminous mixtures for roadsand other paved areas

Part 104:1987 Methods of test for the determination of the density andcompaction

Part 107:1990 Method of test for the determination of the composition ofdesign wearing course rolled asphalt

BS : 729-1971 Hot dip galvanized coating on iron and steel articles

15

Number Designation Title

BS : 812-1995 Testing aggregates

Part 2 Methods for determination of Density

Part 3-75 Methods for determination of mechanical properties

Part 111-90 Method for determination of ten per cent: fines value (TFV)

Part 114-1989 Method for determination of the polished-stone value

BS : 1047-1983 Specification for Air-cooled blast furnace-slag aggregate foruse in construction

BS : 1154-2003 Natural rubber compounds – specifications

BS : 1377-1990 Methods of test for soils for civil engineering purposes

BS : 1447-1988 Mastic asphalt (limestone fine aggregates) for roads andfootways and pavings in buildings

BS : 1449-1956 Steel plate, sheet and strip

Part 1-1991 Carbon steel plate, sheet and strip

Part 2-2008 Stainless and heat resisting plate, sheet and strip

BS : 1470-1987 Wrought aluminium and aluminium alloys for generalengineering purposes – plate, sheet and strip

BS : 2000 Methods of test for petroleum and its products

Part 397:1995 Recovery of bitumen binders-dichloromethane extractionrotary film evaporator method – Withdrawn on 1.11.2007

BS : 2630-1982 Specification for resistance projection welding of uncoatedlow carbon steel sheet and strip using embossedprojections

BS : 2870-1980 Rolled copper and copper alloys : sheet, strip and foil

BS : 3262 Hot-applied thermoplastic road marking materials

Part 1-1989 Specification for constituent materials and mixtures

Part 2-1999 Specification for road performance

Part 3-1989 Specification for application of material to road surface

BS : 5212:Part 2-1990 Code of practice for the application and use of jointsealants

BS : 6044-1987 Specification for pavement marking paints

BS : 6088-1981 Specification for solid glass beads for use with roadmarking compounds and for other industrial uses

16

Number Designation Title

BS : 6906 Methods of test for geotextiles

Part 1-1987 Determination of tensile properties using a wide width strip

Part 2-1989 Determination of the apparent pore size distribution by drysieving

Part 3-1989 Determination of water flow normal to the plane of thegeotextile under a constant head

Part 4-1990 Determination of the puncture resistance 9CBR puncturetest)

Part 7-1990 Determination of in-plane waterflow

BS : 7542-1992 Method of test curing compound for concrete

CRRI & IOC, New Delhi Bituminous road construction handbook

BS : DD232-2006 Method for determination of the maximum binder content ofbituminous mixtures without excessive binder drainage

MS-4 (7th edition) The asphalt handbook (Asphalt Institute)

MS-2 (6th edition) Mix design methods for asphalt concrete and other hot-mixtypes (Asphalt Institute)

MS-14 (3rd edition) Asphalt Cold Mix Manual (Asphalt Institute)

GRI-GG1 Geogrid rib tensile strength (Geosynthetic ResearchInstitute)

GRI-GG2 Geogrid junction strength (Geosynthetic Research Institute)

GRI-GG3 Tensile creep testing of geogrids (Geosynthetic ResearchInstitute)

17