features · on the tool in legible condition.. features: 2.0 hp motor prevents stall under load....

PLEASE READ AND FOLLOW ALL WARNINGS

Read Operating InstructionsAlways become familiar with all theinstructions and warnings before operatingany power tool.Always Wear ApprovedEye ProtectionImpact resistant eye protection shouldmeet or exceed the standards as set forthin the United States ANSI Z87.1,Occupational and Educational Eye andFace Protection. Look for the markingZ87.1 on your eye protection to insure thatit is an approved style. For furtherinformation, ANSI Z87.1, Occupational andEducational Eye and Face Protection, isavailable from the American NationalStandards Institute, Inc., 11 West 42ndStreet, New York, NY 10036.Hearing Protection isRecommendedHearing protection should be used when thenoise level exposure equals or exceeds an8 hour time-weighted average sound levelof 85 dBA. Process noise, reflectivesurfaces, other tools being operatednearby, all add to the noise level present inyour work area. If you are unable todetermine your noise level exposure, werecommend the use of hearing protection.Avoid Prolonged Exposure toVibrationPnuematicTools can vibrate during use.Prolonged exposure to vibration or veryrepetitive hand and arm movements, cancause injury. Stop using any tool ifdiscomfort, tingling feeling or pain occurs.You should consult your physician beforeresuming use of the tool.

90 PSIG MaximumThis tool is designed to operate at an airpressure of 90 pounds per square inchgauge pressure (90 PSIG) maximum, at thetool. Use of higher air pressure can, andmay cause injury. Also, the use of higherair pressure places the internal componentsunder loads and stresses they were notdesigned for, causing premature

Universal ToolA Division of Florida Pneumatic Manufacturing Corporation

851 Jupiter Park Lane, Jupiter, Florida 33458Toll Free 1-800-327-9403

Read these instructions carefully before attempting to install, operate orservice this Florida Pneumatic product. Failure to comply with the instruc-tions could result in personal injury and/or property damage! Retain theseinstructions for future reference.

Safety InstructionsThe following instructions are furnished asgeneral guidelines for use of your pneu-matic tool. They cannot comprehensivelycover all possible or conceivable uses ofthe subject tool. For additional informationon the safe use of air tools, we advise youto obtain a copy of ANSI B186.1 SafetyCode for Portable Air Tools, available fromthe following source:

American National Standards Institute, Inc.

11 West 42nd StreetNew York, NY 10036.

The use of the word “shall” in the followinginstructions, indicates that adherence tothe particular requirement is necessary toconform to ANSI B186.1.

Tool Application and UsagePneumatic tools shall be used only for thepurposes intended in their design andwithin the capacity for which they were

FPMC

WARNING:Some dust created by power sanding, sawing,grinding, drilling, and other construction activitiescontains chemicals known to cause cancer, birthdefects or reproductive harm. Some examples ofthese chemicals are:

•

Lead from lead-based paints

•

Crystalline silica from bricks, cement andother masonry products

•

Arsenic and chromium from chemicallytreated lumber

Your risk from these exposures varies, dependingon how often you do this type of work. To reduceyour exposure to these chemicals, work in a well-ventilated area and work with approved safetyequipment such as those dust masks that arespecially designed to filter out microscopicparticles.

MODEL NO. UT87699” VERTICAL GRINDER

intended and rated. It shall be the tool owner’sand/or employer’s responsibility to instructeach operator in the safe use of the tool.Tools shall not be used without guards andsafety devices as furnished by the manufac-turer. Where an air tool is modified or altered,the modifier shall provide the safeguards toenable it to be safely used in the operationsintended and to comply with any applicableprovisions as contained in ANSI B186.1.

Tool InstallationPressure regulators shall be used to limit airpressure to the rated pressure where thesupply pressure exceeds the tool’s ratedpressure. Air hoses and lines shall berelieved of compressed air before beingdisconnected or disjointed, unless there isautomatic valve closing protection at the jointbeing separated. Synthetic lubricants whichcan cause deterioration of elastomer sealsshall not be used in air systems of air tools.

Tool MaintenanceIt shall be the tool owner.s and/oremployer.s responsibility to assure thattools are maintained in a safe operatingcondition. Tool maintenance and repairshall be performed by authorized,trained, competent personnel. Toolsshall be disconnected from theircompressed air supply before repairsare attempted. Repairs shall beconsistent with the manufacturer.srecommended procedures.Tool, hoses and fittings shall bereplaced if unsuitable for safe operation.It shall be the tool owner.s and/oremployer.s responsibility to keeprequired rating markings and warningson the tool in legible condition.

.

Features: 2.0 HP Motor prevents stall under load. Safety lock-off throttle.Governor controlled to maintain speed for optimum material removalDouble bearing spindle design for durability. Built-in exhaust silencer systemBest for continuous heavy duty grinding

Always use accessories with anRPM rating that meets or exceedsthe tool RPM rating.

Replacement Parts

Limited WarrantyUniversal Tool warrants its tools to be free from defects in material and workmanship for one year from the date ofpurchase. This warranty does not apply to tools which have been abused, misused, modified or repaired bysomeone other than Universal Tool or its authorized service centers. If a Universal Tool proves defective inmaterial of workmanship within one year after purchase, return it to any authorized service center or to UniversalTool, freight prepaid. Please enclose your name, address and adequate proof of purchase date with a briefdescription of the defect. Universal Tool will, at its option, repair or replace defective tools, free of charge. Repairsor replacements are warranted as described above for the remainder of the warranty period. Universal Tool's soleliability and your exclusive remedy under this warranty is limited to repair or replacement of the defective tool.There are no other warranties expressed or implied and Universal Tool shall not be liable for incidental, consequentialor special damages, or any other damages, costs or expense of repair or replacement as described above.

Specifications:

MODEL NO. UT87699” VERTICAL GRINDER

MODEL NO. UT87699” VERTICAL GRINDER

Motor HP .................................................................................................................. 2.0Max. Wheel Diameter ................................................................................... 9” Type 27Exhaust .................................................................................................................. SideSpindle Size ..................................................................................................... 5/8” - 11RPM ...................................................................................................................... 7,000Weight ................................................................................................................. 7.2 lbsLength ................................................................................................................... 12.5”Air Inlet .............................................................................................................1/2” NPTRec Hose ................................................................................................................ 3/8”

N YT’QNOITPIRCSEDON TRAP.O1 988001 1GNISUOH2 9OB-04 1)4.1*5.3( GNIR-O3 988003 VALVE 1METS4 988004 1GNIHSUB5 988005 2GNIR-O6 988006 1REHSAW

1EVLAV80078978 988008 1GNIRPS9 988009 1GNIHSUB TELNI10 988010 1REVEL

1NIP2340791112 988012 1WERCS13 980528 3)6X5M( WERCS14 988014 1ELFFAB TSUAHXE15 988015 NOISE ELIMINATION POLY FIBER 116 988016 1REVOC17 987020 1REDLOH GNIRPS18 987021 1)T5.0*5.9*41( REHSAW19 987022 1)5.61*T2.1*7.9( GNIRPS20 987024 1)L8.11*2( NIP21 987023 1EVLAV RONREVOG22 987027 GO 1EGAC RONREV23 987025 GOVERNOR WE 2THGI24 987026 2NIP RONREVOG25 987028 1REHSAW26 987029 1)ZZ1026( GNIRAEB27 988027 1ETALP RAER28 981326 3)L8*3( NIP29 988029 1REDNILYC30 988030 4EDALB ROTOR31 988031 1ROTOR32 988032 1ETALP TNORF33 988033 2)ZZ3006( GNIRAEB34 988034 1RECNALAB TFAHS ROTOM

1YEK5308895336 988036 1REHSAW37 988037 1REHSAW39 988039 5)L02*6M( WERCS40-1 988040-1 1)"9( REVOC CSID41 988041 F 1ETALPECA42 988042 1TUN CSID43 988043 1TUN CSID44 988044 1WERCS45 988045 STOP SP 1)MM52( RENNA46 987057 1RENNAPS CSID47 960929 1)MM4( XEH48 988048 1ELDNAH49 988049 1)L02*01M( WERCS50 987056 STOP SP 1 )MM91( RENNA