customproducts table of contents introduction
Post on 11-Feb-2022
1 Views
Preview:
TRANSCRIPT
CUSTOM PRODUCTS
Introduction
Table of Contents
Questions & Answers
Detailed Data Sheets
Back to
100 Davids Drive • Hauppauge, NY 11788 • 631-436-7400 • Fax: 631-436-7430 • www.miteq.com
Mixer Home PageMixer Home Page
CONTENTS
IntTIONCorporate OverviewTechnology OverviewSpecification DefinitionsQuality AssuranceMTBF CalculationsManufacturing Flow DiagramsDevice 883 ScreeningGeneral SpecificationsSpace-Qualified Mixers
TABLE OF CONTENTS
CONTENTS
MULTIPLIERS (CONT.)Detailed Data Sheets
Passive Frequency DoublersOctave Bandwidth
MillimeterMultioctave Bandwidth
Drop-In Active Frequency Doublers
Narrow and Octave Bandwidth Drop-In Millimeter
Multioctave Bandwidth Millimeter
Active Multiplier AssembliesX2
Millimeter X3
Millimeter X4
Millimeter X5
Higher Order Multiplication (X20)SRD Comb Generator Higher Order Multiplication (X4)
Outline DrawingsPassive Multipliers Active Multipliers Passive Multipliers
Questions and Answers
CUSTOM PRODUCTSGeneralQuick ReferenceTypical Subsystem Worksheet Useful System FormulasDetailed Data Sheets
Three-Channel LNADownconverter Module
TABLE OF CONTENTS (CONT.)
CONTENTS
CUSTOM PRODUCTSDetailed Data Sheets (Cont.)
Low-Noise Block DownconverterFour-Channel Downconverter ModuleFive-Channel Downconverter Module
with Input RF Switch/Limiter and LO Amplifier/Divider
Block Diagram of MITEQ 5-Channel Gainand Phase-Matched Front-End
Applications of Five-Channel Front EndsFour-Channel 1 to 18 GHz
Image Rejection DownconverterThree-Channel Mixer AmplifierDirect Microwave Digital I/Q
Modulator SystemIntegrated Upconverter and
Power AmplifierBlock DownconverterLow-Noise Block ConverterX-Band Low-Noise Block ConverterSwitched Power Amplifier AssemblyLow-Noise Mixer Preamplifier
with Selectable InputsComb Generator Frequency MultiplierBroadband ConverterX-Band Monopulse Radar ReceiverDual-Channel Signal Processor AssemblyDual-Channel Block Converter
Questions and AnswersMixer Subsystems
Technical ArticleMillimeter-Wave Block Converters
Ordering Information
ISO 9001:2000GENERAL INFORMATIONWARRANTY
INTRODUCTION
This catalog is intended to provide an overview ofMITEQ's Mixer Department's standard products andcustom capabilities. The products within this catalog areorganized into five major sections:
• Mixers• Image rejection mixers• Modulators• Multipliers• Custom Products
In addition to these products, we have included typicaltest data from most in order to give you a feel for theperformances listed in the specification tables. Also,included are technical notes, specification definitions,and questions and answers written by our engineers tohelp in understanding our system design parameters.
To provide an overview of our manufacturing process-es, we have included a section on quality assurance,manufacturing flow diagrams, and options available tothe customer. In addition, we have documented reli-ability predictions for some of our typical mixer mod-els based upon these flow diagrams.
CUSTOM ENGINEERING
This catalog covers only a small percentage ofdesigns available from MITEQ's Mixer Department.For variations on catalog performance or customdesigns, including both electrical and mechanicaldesign efforts, please contact MITEQ for assistance.
TABLE OF CONTENTS (CONT.)
INTRODUCTION
This catalog is intended to provide an overview ofMITEQ's Mixer Department's standard products andcustom capabilities. The products within this catalog areorganized into five major sections:
• Mixers• Image rejection mixers• Modulators• Multipliers• Custom Products
In addition to these products, we have included typicaltest data from most in order to give you a feel for theperformances listed in the specification tables. Also,included are technical notes, specification definitions,and questions and answers written by our engineers tohelp in understanding our system design parameters.
To provide an overview of our manufacturing process-es, we have included a section on quality assurance,manufacturing flow diagrams, and options available tothe customer. In addition, we have documented reli-ability predictions for some of our typical mixer mod-els based upon these flow diagrams.
CUSTOM ENGINEERING
This catalog covers only a small percentage ofdesigns available from MITEQ's Mixer Department.For variations on catalog performance or customdesigns, including both electrical and mechanicaldesign efforts, please contact MITEQ for assistance.
CONTENTSCUSTOM PRODUCTS
General
Quick ReferenceTypical Subsystem Worksheet Useful System FormulasDetailed Data Sheets
Three-Channel LNA Downconverter ModuleLow-Noise Block DownconverterFour-Channel Downconverter ModuleFive-Channel Downconverter Module
with Input RF Switch/Limiter and LO Amplifier/DividerBlock Diagram of MITEQ 5-Channel Gain and Phase-Matched Front-EndApplications of Five-Channel Front EndsFour-Channel 1 to 18 GHz Image Rejection DownconverterThree-Channel Mixer AmplifierDirect Microwave Digital I/Q Modulator SystemIntegrated Upconverter and Power AmplifierBlock DownconverterLow-Noise Block Converter X-Band Low-Noise Block ConverterSwitched Power Amplifier AssemblyLow-Noise Mixer Preamplifier with Selectable InputsComb Generator Frequency MultiplierBroadband ConverterX-Band Monopulse Radar ReceiverDual-Channel Signal Processor AssemblyDual-Channel Block Converter
Questions and AnswersMixer Subsystems
Technical ArticleMillimeter-Wave Block Converters
Ordering Information
ARS309LC7 9 to 9.2 50 to 70 MHz Three-Channel LNA Downconverter Module 467
LNB-1826-30 18 to 26 2 to 10 GHz Low-Noise Block Downconverter 469
LNB-2640-40 26 to 40 2 to 16 GHz Low-Noise Block Downconverter 471
DA40502LC7 .5 to 2 10 to 250 MHz Four-Channel Downconverter Module 473
DA40208LC7 2 to 8 10 to 250 MHz Four-Channel Downconverter Module 473
DA40818LC7 8 to 19 10 to 250 MHz Four-Channel Downconverter Module 473
DSS0818 8 to 18 80 to .240 MHz Five-Channel Downconverter Module withInput RF Switch/Limiter and LO Amplifier/Divider 475
SYS40118C20 1 to 18 20 to 200 MHz Four-Channel 1 to 18 GHz Image Rejection Downconverter 479
IR3A8596LR6 8.5 to 9.6 10 to 250 MHz Three-Channel Mixer Amplifier 480
IR3A5459LR6 5.4 to 5.9 10 to 250 MHz Three-Channel Mixer Amplifier 481
SYS6474N01R 6.4 to 7.4 6.4 to 7.4 GHz Direct Microwave Digital I/Q Modulator System 483
SYSTX3638 1.5 to 2.5 36.5 to 37.5 GHz Integrated Upconverter and Power Amplifier 485
SYS1840A24R 18 to 40 2 to 16 GHz Block Downconverter 487
SYS1840N01R 18 to 40 4 to 18 GHz Low-Noise Block Downconverter 489
LNB-7181-02 7.1 to 8.1 1 to 2 GHz X-Band Low-Noise Block Converter 491
SYS3436N01R 34 to 36 34 to 36 GHz Switched Power Amplifier Assembly 493
SYS0204N01R 2 to 4 55 to 110 MHz Low-Noise Mixer Preamplifier with Selectable Inputs 494
SYS0118N01R 0.1 1 to 18 GHz Comb Generator Frequency Multiplier 495
SYS0218N01R 0.1 2 to 18 GHz Comb Generator Frequency Multiplier 495
SYS0318N01R 0.1 3 to 18 GHz Comb Generator Frequency Multiplier 495
SYS0518N01R 0.5 to 18 8 to 12 GHz Broadband Converter 497
SYS9.0N01R 9.28 to 9.34 135 to 185 MHz X-Band Monopulse Radar Receiver 498
SYS1015N01R 10 to 15 DC to 500 MHz Dual-Channel Signal Processor Assembly 499
SYS0216N01R 18 to 40 2 to 16 GHz Dual-Channel Block Converter 501
GENERALThe MITEQ technical advantage of producing custom integrated assemblies are based on thecore mature component product lines which include:• State-of-the-art low noise amplifiers (LNAs)• High power amplifiers (HPAs)• Wide bandwidth and high dynamic range mixers• Switches and other control products• Low phase noise oscillators and synthesizers
CUSTOM PRODUCTS
INPUT MODEL FREQUENCY OUTPUT
NUMBERS (GHz) FREQUENCY DESCRIPTION PAGE
A sampling of some of the custom subassemblies are shown below. For an individualized quotation, pleasecontact MITEQ with your specific requirement.
465
CU
STO
MPR
OD
UC
TS
466
TYPICAL SUBSYSTEM WORKSHEET
USEFUL SYSTEM FORMULAS
NF = Noise Temperature = 1+ Te
Te = Excess Noise Temperature = (NF - 1) To, To = 290 K
Overall Cascaded Noise Temperature =
Overall Cascaded Noise Temperature =
IP2 Output Cascaded (worst case), (IP2)-1/2 = (IP24)-1/2 + (G4IP23)-1/2 + (G3G4IP22)-1/2 + (G2G3G4IP21)-1/2
IP3 Output Cascaded (worst case), (IP3)-1 = (IP34)-1 + (G4IP33)-1 + (G3G4IP32)-1 + (G2G3G4IP31)-1
Note: All quantities expressed as power ratios.
NF1 + NF2 -1 + NF3 - 1 + NF4 - 1
G1 G1G2 G1G2G3
Te1 + Te2 + Te3 + Te4
G1 G1G2 G1G2G3
To
LNA LNALPF MIXER
LOWPASSLNA FILTER MIXER LNA CASCADE
26 – 40 GHz 40 GHz TB0440LW1 2 – 18 GHz TOTAL
STAGE 1 2 3 4
Noise figure (dB) 2.75 0.5 9 2.5 2.82Gain (dB) 27 -0.5 -9 20 37.5Output IP3 (dBm) 18 100 4 20 18.13Output power (dBm) -13 -13.5 -22.5 -2.5 –
CU
STO
MPR
OD
UC
TS
MODEL: ARS309LC7
FEATURES• RF/LO coverage ................ 9 to 9.3 GHz
• Input limiter diode protection
• Conversion gain ............... 17 dB typical
• Noise figure....................... 5 dB typical
• Channel-to-channel tracking (typical)Phase ................................. ±5°Amplitude .......................... ±0.5 dB
THREE-CHANNEL LNA DOWNCONVERTER MODULE
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF/LO frequency range GHz 9 9.3
RF VSWR (RF = -30 dBm, LO = +17 dBm) Ratio 1.5:1
BIT (built-in-test) common port GHz 9 9.3
Maximum RF input power CW Watts 1
Pulse Watts 50(1µs, 1% duty cycle)
LO power range dBm +16 +18
LO VSWR LO = +17 dBm Ratio 2:1 3:1
DC voltage/current Positive and negative V/mA -15/-0.5 +15/2.5
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
Conversion gain RF input to IF output dB 15 17
Single-sideband noise figure at 25°C dB 5 5.5
BIT phase tracking Degrees -5 +5
LO-to-RF isolation dB 20 25
RF-to-IF isolation dB ±0.5 ±1
Output power at 1 dB compression LO = +17 dBm dBm +10
Output two-tone third-order intercept point LO = +17 dBm dBm +20
Channel-to-channel phase tracking Degrees ±5 ±10
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
IF frequency range MHz 50 70
IF phase linearity 3-pole butterworth Degrees -5 +5
IF VSWR Ratio 2:1 2.5:1
MITEQ’s Model ARS3 Series integrates our best low-noise amplifier and double-balanced image rejection mixerdesigns. Input limiter protection diodes and output IF amplifiers provide a phase and amplitude tracking three-chan-nel downconverter with an integrated BIT and LO distribution network. This unit can be used in a basic monopulsereceiver. In addition, a mating three-channel IF (AGC) unit and I/Q video detector assembly is available.
467
CU
STO
MPR
OD
UC
TS
9 9.05 9.1 9.15 9.2 9.25 9 9.05 9.1 9.15 9.2 9.25
9 9.05 9.1 9.15 9.2 9.25 9 9.05 9.1 9.15 9.2 9.25
2.0:1
1.8:1
1.6:1
1.4:1
1.2:1
FREQUENCY (GHz)
0
10
20
30
40
+1
0
-1
0
20
40
60
80
FREQUENCY (GHz)
CON
VER
SIO
N G
AIN
(dB)
VSW
R (R
ATIO
)
LO-T
O-R
F IS
OLA
TIO
N (d
B)
PHASE TR
ACKING
(DEG
.)CH
ANN
EL-TO-CH
ANN
EL ISOLATIO
N (dB)
AMPL
ITU
DE
TRAC
KIN
G (d
B)
CONVERSION GAIN / NOISE FIGURE
NO
ISE FIGU
RE (dB)
VSWR (LO = +17 dBm) ISOLATION
18
16
12
8
4
18
16
12
8
4
FREQUENCY (GHz)
+10 +5 0 -5 -10
FREQUENCY (GHz)
AMPLITUDE / PHASE TRACKING
PHASE TRACKING
AMPLITUDE TRACKING
RF
LO
NOISE FIGURE
CONVERSION FIGURE
CHANNEL TO CHANNEL
LO TO RF
AZ
EL
AZ
EL
ARS309LC7 TYPICAL TEST DATA
MAXIMUM RATINGSOperating temperature ........................ -40 to +65°CStorage temperature .......................... -55 to +100°C
FUNCTIONAL BLOCK DIAGRAMOUTLINE DRAWING
AVAILABLE OPTIONSAGC, IF module.I/Q detector module.Digital output.
468
NOTE: Test data supplied at 25°C; Conversion loss, LO-RF isolation.
NOTE: All dimensions shown in brackets [ ] are in millimeters.
CU
STO
MPR
OD
UC
TS
5.500 [139.70].375 [9.525] TYP..187 [4.750] TYP.
6.000[152.40]
1.562[39.675]
3.125[79.375]
4.607[117.018]
.975[24.765]
2.366[60.010]
.237 [6.020].312 [7.925].315 [8.001]
3.881[98.577]
5.396[137.058]
6.250[158.75]
5.126 [130.200]
5.396[137.058]
3.881 [98.577]
2.366[60.096]
.851 [21.615]
.125[3.175]TYP.
IF OUT
IF OUT
IF OUT
LO INRF BIT
IN LOM
ONIT
OROU
TRF
INRF
INRF
IN
PWR
CONN, PWR M24308/4-1 CONNECTORS, RFSMA FEMALE (9 PLACES)
.193 [4.902] DIA THRU. (TYP. 4 PLACES)
IF LNALNA MIXERCOUPLERDIODE LIMITER
DOUBLE-BALANCEDIR
LO Input
BIT LO Monitor Output
LO Power Divider
CU
STO
MPR
OD
UC
TS
MODEL SERIES: LNB-1826-30
FEATURES• RF frequency range.......... 18 to 26 GHz
• Conversion gain ............... 42 dB typical
• Noise figure....................... 3 dB maximum
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range GHz 18 26
RF VSWR 50 ohm reference Ratio 2.5:1
LO frequency (fixed, internal) GHz 28
Reference input frequency MHz 10
Reference input power dBm 0
DC power +15 VDC Amp 1
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.Conversion gain dB 42
Single-sideband noise figure at 25°C dB 2.5 3
LO-to-RF isolation dB 45
LO-to-IF isolation dB 30
RF-to-IF isolation dB 20
Output power at 1 dB compression dBm +7
Output two-tone third-order intercept point dBm +17
Image rejection dB 20 25
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.IF frequency range GHz 2 10
IF VSWR 50 ohm reference Ratio 2.5:1
These wide RF/IF bandwidth frequency converters, with fixed LO frequencies (block converters), are commonlyused to process millimeter signals with less expensive receivers below 18 GHz. In some applications, the resultingsignals are upconverted back into the millimeter band. The LNB series, with its 4 dB noise figure, permits opera-tion at low input signal powers. In addition, the PM noise of the converter is minimized by a phase-locked and mul-tiplied internal LO source. The block diagram shown above is a baseline configuration. ALTERNATIVE CONFIG-URATIONS ARE AVAILABLE.
469
LOW-NOISE BLOCK DOWNCONVERTERS
CU
STO
MPR
OD
UC
TS
30 31.6 33.2 34.8 36.4 38
CON
VER
SIO
N G
AIN
(dB)
FREQUENCY (GHz)
CONVERSION GAIN
18 19.6 21.2 22.8 24.4 26 18 21.420.2819.14 22.56 23.7 24.84 261
1.5
2
2.5
3
3.5
4
FREQUENCY (GHz)
NOISE FIGURE
NO
ISE
FIG
UR
E (d
B)
IMAG
E R
EJEC
TIO
N
FREQUENCY (GHz)
IMAGE REJECTION
1-180
-160-170
-140-130-120
-100-110
-90-80-70-60
-20
-50
-30
-10
-150
-40
0
10010FREQUENCY (Hz)
PHASE NOISE (Option 09)
10K1K 1M100K 100M10M100
90
80
70
60
50
40
30
20
10
0
0
10
20
30
40
50
60
70
80
90
100
LNB-1826-30 TYPICAL TEST DATA
470
AVAILABLE OPTIONS
Option Number01 LO frequency set at 16 GHz, LO < RF operation.02 Bias (contact MITEQ).03 Conversion gain (contact MITEQ).04 Noise figure (contact MITEQ).05 +10 dB minimum output 1 dB compression point. 06 Additional environmental conditions (contact MITEQ).07 Mechanical, RF input, WR42 waveguide.08 External LNA for remote feed applications.09 Low phase noise LO utilizing an internal reference
with frequency stability to ±1 PPM.
NOTE: Test data supplied at 25°C; conversion gain, noise figure and 1 dB compression point.
NOTE: When ordering, please specify model number and option number(s) required.
ENVIRONMENTAL CONDITIONSSpecification temperature ........ +25°CStorage temperature ................ -55 to +85°C minimumHumidity .................................... 95% noncondensing
X/N
RF IN RF OUT
REF
NOTE: All dimensions shown in brackets [ ] are in millimeters.
OUTLINE DRAWING BLOCK DIAGRAM
1.52 [38.61]3.05 [77.47]
1.75 [44.45]
TYPE SMA FEMALE CONNECTOR
PIN 2, GND
P1
PIN 1, +15V10 MHz
REF INPUTPIN 6, ALARMPIN 5, N.C.
PIN 7, N.C.PIN 8, N.C.PIN 9, N.C.
PIN 4, GNDPIN 3, N.C.
TYPE SMAFEMALE CONNECTOR
3.48[88.39]
1.59[40.39]
5.50 [139.70] CONNECTOR, TYPE"SMA" FEMALE
TYPE "K" (LB-2640)TYPE "SMA" (LNB-1826) FEMALE CONNECTOR
8.68 [220.47]
1.77 [44.96]
14.44 [366.78]12.60 [320.04]
CU
STO
MPR
OD
UC
TS
MODEL SERIES: LNB-2640-40
FEATURES• RF frequency range.......... 26 to 40 GHz
• Conversion gain ............... 42 dB typical
• Noise figure....................... 4 dB maximum
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range GHz 26 40
RF VSWR 50 ohm reference Ratio 2.5:1
LO frequency (fixed, internal) GHz 42
Reference input frequency MHz 10
Reference input power dBm 0
DC power +15 VDC Amp 1
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.Conversion gain dB 42
Single-sideband noise figure at 25°C dB 3.5 4
LO-to-RF isolation dB 45
LO-to-IF isolation dB 30
RF-to-IF isolation dB 20
Output power at 1 dB compression dBm +7
Output two-tone third-order intercept point dBm +17
Image rejection dB 20 25
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.IF frequency range GHz 2 16
IF VSWR 50 ohm reference Ratio 2.5:1
These wide RF/IF bandwidth frequency converters, with fixed LO frequencies (block converters), are commonlyused to process millimeter signals with less expensive receivers below 18 GHz. In some applications, the resultingsignals are upconverted back into the millimeter band. The LNB series, with its 4 dB noise figure permits operationat low input signal powers. In addition, the PM noise of the converter is minimized by a phase-locked and multi-plied internal LO source. The block diagram shown above is a baseline configuration. ALTERNATIVE CONFIGU-RATIONS ARE AVAILABLE.
471
LOW-NOISE BLOCK DOWNCONVERTERS
CU
STO
MPR
OD
UC
TS
26
CON
VER
SIO
N G
AIN
(dB)
28.8 31.6FREQUENCY (GHz)
CONVERSION GAIN
34.4 37.2 40 261
1.5
2
2.5
3
3.5
4
28 30FREQUENCY (GHz)
NOISE FIGURE
32 34 36 38 40
NO
ISE
FIG
UR
E (d
B)
44
IMAG
E R
EJEC
TIO
N
45.2 46.4FREQUENCY (GHz)
IMAGE REJECTION
47.36 48.8 50 100-170-160-150-140
-120-130
-110-100-90-80
-40
-70
-50
-30
-60
-20
1KFREQUENCY (Hz)
PHASE NOISE (Option 09)
10K 100K 1M50
45
40
35
30
25
20
15
10
5
0
0
5
10
15
20
25
30
35
40
45
50
LNB-2640-40 TYPICAL TEST DATA
OUTLINE DRAWING BLOCK DIAGRAM
1.52 [38.61]3.05 [77.47]
1.75 [44.45]
TYPE SMA FEMALE CONNECTOR
PIN 2, GND
P1
PIN 1, +15V10 MHz
REF INPUTPIN 6, ALARMPIN 5, N.C.
PIN 7, N.C.PIN 8, N.C.PIN 9, N.C.
PIN 4, GNDPIN 3, N.C.
TYPE SMAFEMALE CONNECTOR
3.48[88.39]
1.59[40.39]
5.50 [139.70] CONNECTOR, TYPE"SMA" FEMALE
TYPE "K" (LB-2640)TYPE "SMA" (LNB-1826) FEMALE CONNECTOR
8.68 [220.47]
1.77 [44.96]
14.44 [366.78]12.60 [320.04]
472
AVAILABLE OPTIONS
Option Number01 LO frequency set at 24 GHz, LO < RF operation.02 Bias (contact MITEQ).03 Conversion gain (contact MITEQ).04 Noise figure (contact MITEQ).05 +10 dB minimum output 1 dB compression point. 06 Additional environmental conditions (contact MITEQ).07 Mechanical, RF input, WR28 waveguide.08 External LNA for remote feed applications.09 Low phase noise LO utilizing an internal reference with
frequency stability to ±1 PPM.NOTE: When ordering, please specify model number and option number(s) required.
ENVIRONMENTAL CONDITIONSSpecification temperature ...... +25°CStorage temperature .............. -55 to +85°C minimumHumidity .................................. 95% noncondensing
NOTE:Test data supplied at 25°C;conversion gain, noise figure and 1 dB compression point
X/N
RF IN RF OUT
REF
NOTE: All dimensions shown in brackets [ ] are in millimeters.
CU
STO
MPR
OD
UC
TS
473
MODEL SERIES: DA4
FEATURES• RF/LO coverage ................ 0.5 to 18 GHz
• Input limiter diode protection
• Conversion gain ............... 25 dB typical
• Noise figure....................... 8.5 dB typical
• Channel-to-channel tracking Phase ................................. ±5° typicalAmplitude .......................... ±0.5 dB typical
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF/LO frequency range DA40502LC7 GHz 0.5 2DA40208LC7 GHz 2 8DA40818LC7 GHz 8 18
Maximum RF input power CW Watts 1Pulse Watts 50
(1µs, 1% duty cycle)
LO power range dBm +13 +15RF and LO VSWR (RF = -10 dBm, LO = +15 dBm) Ratio 2:1 3:1
DC bias +15 V mA 150
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
Conversion gain (RF input to IF output) dB 23 25
Single-sideband noise figure at 25°C 0.5 to 4 GHz dB 8 104 to 18 GHz dB 9 11
LO-to-RF isolation dB 20 25
LO-to-IF isolation dB 20
RF-to-IF isolation dB 20
Output power at 1 dB compression LO = +15 dBm dBm +10
Output two-tone third-order intercept point LO = +15 dBm dBm +20
Channel-to-channel amplitude tracking dB ±0.5 ±1
Channel-to-channel phase tracking Degrees ±5 ±10
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
IF frequency range MHz 10 250
IF VSWR (IF = -10 dBm, LO = +15 dBm) Ratio 2:1
MITEQ’s Model DA4 Series integrates our standard broadband double-balanced mixer designs with input limiterprotection diodes and IF amplifiers to provide a phase- and amplitude-tracked four-channel downconverter with anintegrated LO distribution network. This unit can be used for basic direction finding (D.F.) experiments with fourantennas. In addition, three of the four channels can also be used for a monopulse radar receiver and the fourthused for spur identification.
FOUR-CHANNEL DOWNCONVERTER MODULE
CU
STO
MPR
OD
UC
TS
NOTE: All dimensions shown in brackets [ ] are in millimeters.
474
2 2.4 2.8 3.2 3.6 4
6:1
5:1
4:1
3:1
2:1
FREQUENCY (GHz)2 2.4 2.8 3.2 3.6 4
0
10
20
30
40
0
20
40
60
80
FREQUENCY (GHz)
CON
VER
SIO
N G
AIN
(dB)
VSW
R (R
ATIO
)
LO T
O R
F (d
B)
PHASE TR
ACKING
(DEG
.)CH
ANN
EL TO CH
ANN
EL (dB)
AMPL
ITU
DE
TRAC
KIN
G (d
B)
2
CONVERSION GAIN / NOISE FIGURE
NO
ISE FIGU
RE (dB)
VSWR (LO = +15 dBm) ISOLATION
2.4 2.8 3.2 3.6 4
30
25
20
15
10
16
14
12
8
4
FREQUENCY (GHz)2 2.4 2.8 3.2 3.6 4
+2 +1 0 -1 -2
+10 +5 0 -5 -10
FREQUENCY (GHz)
AMPLITUDE / PHASE TRACKING
PHASE
AMPLITUDE
RF
LO
NOISE FIGURE
CONVERSION FIGURE
CHANNEL TO CHANNEL
LO TO RF
DA40204L TYPICAL TEST DATA
MAXIMUM RATINGSOperating temperature ........................ -54 to +85°CStorage temperature .......................... -65 to +125°C
OUTLINE DRAWING FUNCTIONAL BLOCK DIAGRAM
AVAILABLE OPTIONSMultioctave RF coverage.RF built-in-test (BIT) input.Microwave IF coverage.High dynamic range operation.
3.48 [88.39]3.04 [77.22]
1.3 [33.02].22 [5.59]
3.48[88.39]
2.78[70.61]
2.04[51.82]
1.44 [36.58]
.70 [17.78]
.23 [5.84]
.75 [19.05]
2.39 [60.71]
2.89 [73.41]
3.08[78.23]
2.34[59.44]
.12 [3.05]
I1
I2
LOIN
I3
I4R4
+15V GND
R2
R1
R3
.53 [13.46].23 [5.60] .40 [10.16]
1.14[28.96] 1.74
[44.20]
3.24[82.30]
.125 [3.18] DIA THRU(6 HOLES)
Channel 1Output
Channel 2Output
IF LNADIPLEXERMIXERDIODE LIMITER
DOUBLE-BALANCED
Channel 3Output
Channel 4Output
Channel 1Input
Channel 2Input
Channel 3Input
Channel 4Input
LOInput LO Power
Divider
NOTE: Test data supplied at 25°C; conversion gain, LO-to-RF isolation, noise figure, amplitude and phase balance.
475
MODEL SERIES: DSS0818FEATURES• RF/LO coverage ................ 8 to 18 GHz
• Ideal for broadband DF receivers
• External IF phase/amplitude adjustments
• Channel-to-channel RF tracking Phase ................................. ±5° typicalAmplitude .......................... ±0.5 dB typical
• Remote band/blanking/BIT selection
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF/LO frequency range LO1 and LO2 GHz 8 18
RF power, 1 dB compression @ 6 dB gain nominal dBm -7
RF power Maximum average Watts 2
RF power (maximum peak, Watts 2005 µs pulse, 1% duty cycle)
LO power, operating LO1 and LO2 dBm -18 -15 -12
RF and LO VSWR (RF = -10 dBm, LO = -15 dBm) Ratio 1.5:1
BIT (built-in-test) control (3 BITS) Logic TTL
DC current at ±12 V mA 700
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.Conversion gain (RF input to IF output, dB 3 8 13with gain adjustment of ±5 dB)
Conversion gain flatness Across RF band ±dB 1
Single-sideband noise figure at 25°C dB 10 14
LO-to-RF isolation Including LO amplifier gain dB 0 5 10
LO-to-IF isolation dB 50
RF-to-IF isolation dB 60
Output two-tone third-order intercept point LO = -15 dBm dBm +25
Output two-tone second-order intercept point dBm +48
Channel-to-channel isolation dB 40
Channel-to-channel amplitude tracking dB ±0.5 ±1
Channel-to-channel phase tracking Degrees ±5 ±15
IF gain adjust ±dB 5
IF phase adjust ±Degrees 20
OUTPUT PARAMETERS UNITS MIN. TYP. MAX.
IF frequency range -3 dB bandwidth MHz 80 160 240
IF VSWR (IF = -10 dBm, LO = -15 dBm) Ratio 2:1
MITEQ’s Model DSS Series integrates our standard broadband double-balanced mixer designs with input limiter protectiondiodes and IF amplifiers to provide a phase- and amplitude-tracked five-channel downconverter with an integrated LOamplifier/splitter. A three-way input switch/limiter provides remote band/blanking/BIT select and protection from undesiredhigh signal levels. This module is most often used as the “front-end” of a direction-finding system using four antennas inthe azimuth, elevation or combined directions and a fifth antenna channel to resolve additional received strong “back or sidelobe” signals and to identify the receiver image response. The DSS0818 is also useful as an instantaneous frequency mon-itor with suitable input frequency to phase encoders (application notes available).
FIVE-CHANNEL DOWNCONVERTER MODULE WITH INPUT RFSWITCH/LIMITER AND LO AMPLIFIER/DIVIDER
CU
STO
MPR
OD
UC
TS
NOTE: All dimensions shown in brackets [ ] are in millimeters.
476
8 10 12 14 16 18
3.5:1
3.0:1
2.5:1
2.0:1
1.5:1
1.0:1
FREQUENCY (GHz)
VSW
R (R
ATIO
)
LO T
O R
F (d
B)AM
PLIT
UD
E TR
ACKI
NG
(dB) PH
ASE TRACKIN
G (D
EG.)
NO
ISE FIGU
RE (dB)
CHAN
NEL TO
CHAN
NEL (dB)
8 10 12 14 16 18
0
10
20
30
40
0
20
40
60
80
FREQUENCY (GHz)
CON
VER
SIO
N L
OSS
(dB)
8
CONVERSION GAINNOISE FIGURE
VSWR(LO = +15 dBm) ISOLATION
10 12 14 16 18
20
16
12
8
4
0
16
14
12
8
4
FREQUENCY (GHz)8 10 12 14 16 18
+2+10-1
-2.0
+10+50-5-10
FREQUENCY (GHz)
PHASE AND AMPLITUDE TRACKING
CHANNEL TO CHANNEL
PHASE
AMPLITUDE
LO
RF
LO TO RF
CONVERSION GAIN
NOISE FIGURE
DSS0818 TYPICAL TEST DATA
OUTLINE DRAWING
DC
VB
A
M/N SA0502C06B
RF PROCESSOR
S/N XXXXXX
3.875[98.43]
.250[6.35]
6.125 [155.58]
5.625 [142.88].250[6.35]
.171 [4.34] DIA THRU(6 HOLES)
PHAS
EAD
JG
AIN
ADJ
J11
J10
J12
J6 L
O1
J7 L
O2
J9J8
3.325[84.46]
4.375111.13]
CONN, RFSMA FEMALE
IF OUTPUTS:CONNECTOR: RFSMA FEMALE(5 PLACES)
3.32584.46]
.330 [8.38]
.28 [7.11]
.640 [16.26]
.600 [15.24] (TYP.)
CONNECTOR, RFSMA FEMALE(10 PLACES)
AJ1J6
DJ4J9
CJ3J8
TJ5J10
BJ2J7
8.50±.125 [215.90]
3.500[88.90]
2.812 [71.42]
RF
INCH
ANN
ELS
J18PO
WER
BAND 3(J6; J7; J10; J8; J9)
D TYPE CONNECTOR (15 PIN)DC POWER AND CONTROL SIG.
(MATCHING CONNECTOR SUPPLIED)
BAND 2(J1; J2; J3; J4; J5)
CU
STO
MPR
OD
UC
TS
477
J3
J15J6BAND 2
CHANNEL D
BAND 3IF OUTCHANNEL D
DIPLEXER PHASE ADJ GAIN ADJ
J5
J17J10BAND 2
CHANNEL C
BAND 3IF OUTCHANNEL C
DIPLEXER PHASE ADJ GAIN ADJ
J2
J14J7BAND 2
CHANNEL B
BAND 3IF OUTCHANNEL B
DIPLEXER PHASE ADJ GAIN ADJ
J1 SW/LIM.
J13
PHASE AND GAIN BOARD
J6BAND 2
CHANNEL A
BAND 3IF OUTCHANNEL A
DIPLEXER PHASE ADJ GAIN ADJ
INPUT
LOINPUT
BITINPUT
EXTERNAL ADJUST (TYPICAL 5 PLACES)
EXTERNAL ADJUST (TYPICAL 5 PLACES)
J4
J16J9BAND 2
CHANNEL V
BAND 3IF OUTCHANNEL V
DIPLEXER PHASE ADJ GAIN ADJ
MIXER ASSEMBLY
APPLICATION NOTES
BLOCK DIAGRAM OF SIMPLE TWO-CHANNEL ANGLE OF ARRIVAL(A.O.A) MEASUREMENT SYSTEM (REF 1.)
PHASE DETECTOR
INP
UT
SIG
NA
L
D S
IN Ø
PHASE DIFFERENCES = ψ = -2 D
SIN Ø
Ø
MITEQ PDL SERIES
LIM
LIM
LOCAL OSC
B
A
λ
D
Ø
Ø
PHASE/AMP. FREQUENCYCHANNEL TRACKING CONVERSION
A • RF > LO
B • RF > LO
C • RF > LO
D • RF > LO
T RF < LO
1. “Microwave Passive Direction Finding”, S. Lipsky, 1987, John Wiley & Sons publisher TK6565.D5L57.
BLOCK DIAGRAM OF MITEQ 5-CHANNEL GAIN- AND PHASE-MATCHED FRONT END
CU
STO
MPR
OD
UC
TS
478
APPLICATIONS OF FIVE-CHANNEL FRONT ENDS
MITEQ IQM SERIES
FREQ.TO PHASE ENCODING, CABLE LENGTH
RF IN
0° 3 dB
90° 3 dB
K SIN Ø
K COS Ø
R
L
R
L
LIMITER 0° 3 dB
VERT.HORIZ.
PHASE-MATCHED FIVE-CHANNEL MIXER, LIMITER PHASE DETECTOR SET
REF COURSE RESOLUTION
ANGLE INDICATORS
REF R2
L1 L1 2L1 4L1
R3 R4 R5
PHASE-MATCHED FIVE-CHANNEL MIXER, LIMITER PHASE DETECTOR SET
REF COURSE RESOLUTION
INSTANTANEOUS FREQ. MONITOR (IFM)
FREQ. TO PHASE ENCODER, CABLE NETWORK
FREQUENCY INDICATORS
O–1O–1 O–2O O–3O O–4O O–5O
REF R2 R3 R4 R5
DIRECTION FINDING APPLICATIONS
Can the basic direction-finding receiver also be used to measure incoming frequency?
Yes, by first encoding the received signal into two separate outputs that have a phase difference in direct proportion to their frequency:
A large cable length difference in the two splitter outputs will yield rapidly varying phase with frequency. If theseoutputs are applied to a two-channel DF system, the output phase difference, together with knowledge of theencoder cable lengths, can be used to determine input frequency. This is the basic principle of an instanta-neous frequency monitor (IFM). In actual practice, several frequency encoders are used with progressivelygreater frequency resolution, similar to how one reads the dials of a gas or an electric meter.
ALTERNATIVE APPLICATIONS
CU
STO
MPR
OD
UC
TS
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range GHz 1 18
RF VSWR LO = +20 dBm Ratio 3.5:1
LO frequency range GHz 1 18
LO VSWR LO = +20 dBm Ratio 2.5:1
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
RF-to-IF conversion loss LO = +20 dBm dB 14
Channel to channel LO = +20 dBmAmplitude tracking dB -1.5 +1.5Phase tracking Degrees -15 +15Isolation dB 30
Image rejection dB 15
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
IF frequency range See IF options below 20 200
IF VSWR LO = +20 dBm Ratio 2:1
479
MODEL: SYS40118C20__
FEATURES• Four-amplitude and phase-matched channels
• RF/LO coverage ................ 1 to 18 GHz
• IF option * A: 20 to 40 MHz
B: 40 to 80 MHz
C: 100 to 200 MHz
FOUR-CHANNEL 1 TO 18 GHz IMAGE REJECTION DOWNCONVERTER
MAXIMUM RATINGSSpecification temperature ........ +25°COperating temperature ............ -54 to +85°CStorage temperature ................ -65 to +125°C
OUTLINE DRAWING
NOTE: All dimensions shown in brackets [ ] are in millimeters.
NOTE: Test data supplied at 25°C;conversion loss, amplitude and phase tracking, channel-to-channel isolation, LO-to-RF isolation and image rejection.
Available IF frequency options: SYS40118C20__
A: 20 to 40 MHzB: 40 to 80 MHzC: 100 to 200 MHz
3.500 [88.90]
0.69[17.53]
2.20 [55.88]
4X Ø.100 [2.54] MTG. HOLES
0.080[2.03]
0.375 [9.525] TYP.
3.840[97.536]
1.400[35.56]
2.100[53.34]
0.250 [6.35]
0.700[17.78]
2.800[71.12]
3.500[88.90]
4.000[101.60]
2.000[50.80]
0.500[12.70]
.1000[25.40]
IF OUT (9, 10) (REAL)
IF OUT (11, 12) (IMAGE)
RF IN (1, 2)
LO IN
RF IN (3, 4)
IF OUT (7, 8) (IMAGE)
IF OUT (5, 6) (REAL)
0.250[6.35]
0.500[12.70]
13X FEMALE SMA TYPE FIELD REPLACEABLE CONNECTOR
*
CU
STO
MPR
OD
UC
TS
*
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range GHz 8.5 9.6
RF VSWR LO = +13 dBm Ratio 2:1
LO frequency range LO > RF GHz 8.5 9.6
LO power range dBm +13 +16
LO VSWR LO = +13 dBm Ratio 1.5:1
Bias +15 VDC mA 150
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
RF-to-IF conversion gain LO = +13 dBm dB 20
Single-sideband noise figure at 25°C LO = +13 dBm dB 6 6.7
Channel to channel LO = +13 dBmAmplitude tracking dB -0.5 +0.5Phase tracking Degrees -5 +5Isolation dB 30
Image rejection LO < RF dB 20
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
IF frequency range See IF options below 20 200
IF VSWR LO = +13 dBm Ratio 2:1
MODEL: IR3A8596LR6__
FEATURES• Three-amplitude and phase-matched channels
• RF/LO coverage ................ 8.5 to 9.6 GHz
• IF option * A: 20 to 40 MHz
B: 40 to 80 MHz
C: 100 to 200 MHz
THREE-CHANNEL MIXER AMPLIFIER
OUTLINE DRAWING
** Is optional.NOTE: All dimensions shown in brackets [ ] are in millimeters.
4X #6-32NC-2THD X .312 [7.92] DP. MIN. C'BORE .171 [4.34] DIA. X .050 [1.27] DP. (BOTH SIDES)
50 OHMTERMINATION
3.500 [88.90]
3.250 [82.55]0.125 [3.175]0.125 [3.175]
2.366[60.096]
0.312 [7.925]
0.851[21.62]
3.881[98.577]
5.396[137.058]
6.250[158.75]
6.000[152.40]
6X CONNECTORS,RF SMA FEMALE
FILTERCAPACITOR
GND STUD
3.125[79.38]
0.851[21.615]
2.367[60.122]
3.881[98.577]
5.000[127.0]
5.396[137.058]
0.237 [6.02]0.315 [8.00]
J7IF OUT
(CHAN B)
J6IF OUT
(CHAN A)
J3RF IN
(CHAN B)
J2RF IN
(CHAN A)
J1LO IN
J4RF IN
(CHAN C)
J5LO
MONITOR+ VDC
MGC **
J8IF OUT
(CHAN C)
0.23 [5.84]
0.240 [6.10]
0.975 [24.765]0.625 [15.875] MAX.
480
*
CU
STO
MPR
OD
UC
TS
MAXIMUM RATINGSSpecification temperature ........ +25°COperating temperature ............ -54 to +85°CStorage temperature ................ -65 to +125°C
NOTE: Test data supplied at 25°C;conversion loss, amplitude and phase tracking, channel-to-channel isolation, LO-to-RF isolation and image rejection.
Available IF frequency options: IR3A8596LR6__
A: 20 to 40 MHzB: 40 to 80 MHzC: 100 to 200 MHz
*
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range GHz 5.4 5.9
RF VSWR LO = +13 dBm Ratio 2:1
LO frequency range LO > RF GHz 5.4 5.9
LO power range dBm +13 +16
LO VSWR LO = +13 dBm Ratio 1.5:1
Bias +15 VDC mA 150
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
RF-to-IF conversion gain LO = +13 dBm dB 20
Single-sideband noise figure at 25°C LO = +13 dBm dB 6 6.7
Channel to channel LO = +13 dBmAmplitude tracking dB -0.5 +0.5Phase tracking Degrees -5 +5Isolation dB 30
Image rejection LO < RF dB 20
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
IF frequency range See IF options below 20 200
IF VSWR LO = +13 dBm Ratio 2:1
481
MODEL: IR3A5459LR6__
FEATURES• Three-amplitude and phase-matched channels
• RF/LO coverage ................ 5.4 to 5.9 GHz
• IF option * A: 20 to 40 MHz
B: 40 to 80 MHz
C: 100 to 200 MHz
THREE-CHANNEL MIXER AMPLIFIER
*
OUTLINE DRAWING4X #6-32NC-2THD X .312 [7.92] DP. MIN. C'BORE .171 [4.34] DIA. X .050 [1.27] DP. (BOTH SIDES)
50 OHMTERMINATION
3.500 [88.90]
3.250 [82.55]0.125 [3.175]0.125 [3.175]
2.366[60.096]
0.312 [7.925]
0.851[21.62]
3.881[98.577]
5.396[137.058]
6.250[158.75]
6.000[152.40]
6X CONNECTORS,RF SMA FEMALE
FILTERCAPACITOR
GND STUD
3.125[79.38]
0.851[21.615]
2.367[60.122]
3.881[98.577]
5.000[127.0]
5.396[137.058]
0.237 [6.02]0.315 [8.00]
J7IF OUT
(CHAN B)
J6IF OUT
(CHAN A)
J3RF IN
(CHAN B)
J2RF IN
(CHAN A)
J1LO IN
J4RF IN
(CHAN C)
J5LO
MONITOR+ VDC
MGC **
J8IF OUT
(CHAN C)
0.23 [5.84]
0.240 [6.10]
0.975 [24.765]0.625 [15.875] MAX.
MAXIMUM RATINGSSpecification temperature ...... +25°COperating temperature ............ -54 to +85°CStorage temperature................ -65 to +125°C
NOTE: Test data supplied at 25°C;conversion loss, amplitude and phase tracking, channel-to-channel isolation, LO-to-RF isolation and image rejection.
Available IF frequency options: IR3A5459LR6__
A: 20 to 40 MHzB: 40 to 80 MHzC: 100 to 200 MHz
*
** Is optional.NOTE: All dimensions shown in brackets [ ] are in millimeters.
CU
STO
MPR
OD
UC
TS
482
CU
STO
MPR
OD
UC
TS
This page is intentionally blank
CU
STO
MPR
OD
UC
TS
6.4 TO 7.4 GHz DIRECT MICROWAVE DIGITAL I/Q MODULATOR
MODEL: SYS6474N01R (Carrier Driven)
FEATURES• RF bandwidth............................... 6.4 to 7.4 GHz
• I/Q bandwidth............................... DC to 100 MHz
• Phase accuracy ........................... ±2°
• Sideband harmonics ................... -30 dBc
• Carrier rejection........................... -30 dBc
• BIT output .................................... TTL
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
Frequency range (carrier) GHz 6.4 7.4
RF VSWR 50 ohm reference Ratio 1.5:1
RF power range dBm 0 +5 +10
I/Q frequency range (modulation) MHz DC 100
I/Q volt range Volts -0.2 +0.2
I/Q VSWR 50 ohm reference Ratio 1.5:1
DC current +12 V mA 150
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
Conversion gain (relative to I/Q inputs) RF = +5 dBm dB 0 3
RF phase accuracy (static) I/Q = ±0.2 V, 50 ohms Degrees ±2 ±5
Sideband rejection (fo - fm) Relative dBc 25
Carrier rejection (fo) to dBc 25 30
Second-harmonic rejection (fo ± 2fm) desired dBc 30 35
Third-harmonic rejection (fo ± 3fm) sideband dBc 30 40
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.RF frequency (modulated carrier) 6.4 7.4
RF VSWR RF input: +5 dBm Ratio 1.2:1
RF power (I/Q = +0.2 volts) RF input: +5 dBm dBm +10
BIT voltage (I/Q off, I/Q on) RF input: +5 dBm Volts .30 Off/On 3
APPLICATIONThis linear IF digital modulator accepts ±0.2 volts input I/Q Gaussian shaped pulses and provides QAM RF with thesame envelope shape. Less channel bandwidth is required when the modulation is shaped and the I/Q phase statesare also differentially coded (DQPSK). Input and output buffer amplifiers are provided to ensure that generator and loadmismatches do not affect quadrature accuracy and the resulting symbol error rate.
Relative
to
desired
sideband
483
CU
STO
MPR
OD
UC
TS
BLOCK DIAGRAM
CARRIER DRIVEN TYPICAL TEST DATA
MAXIMUM RATINGSSpecification temperature ...................... +25°COperating temperature ............................ -54 to +85°CStorage temperature .............................. -65 to +125°C
OUTLINE DRAWING BLOCK DIAGRAM
GENERAL NOTE1. Insertion loss relative to 0 dBm IF input. All other outputs,
including fo, are relative to the desired upper (fo + fm) output.
Voltage Ø 0° 90° 180° 270°I (Volts) +0.2 +0.2 -0.2 -0.2Q (Volts) +0.2 -0.2 -0.2 +0.2
484
DYNAMIC MODULATION SPECTRUM (RF level = +6 dBm, I/Q level = +4 dBm total, = 20 MHz)
Frequency fo + IF fo - IF fo fo - 2 IF fo + 2 IF fo - 3 IF fo + 3 IF(GHz) (I.L., dB) (dBc) (dBc) (dBc) (dBc) (dBc) (dBc)
Note 16 7.2 30.1 31 53 33 44 49
6.4 6.9 23.5 32 62 35 42 446.8 6 27.8 30 64 34 46 517.2 4.7 32 29 57 38 42 527.6 3.9 23.5 31 58 36 38 408 3 20.5 31 55 37 33 38
RF IN
RF OUT
I
Q
DC
BIT
+2.5+2.0+1.5+1.0+0.5
0-0.5 -1.0 -1.5 -2.0 -2.5
1086420-2 -4 -6 -8 -10
FREQUENCY (GHz)FREQUENCY (GHz)
QPSK AMPLITUDE BALANCE (RF = +5 dBm, I/Q = ±0.2V)
AMPL
ITU
DE
BALA
NCE
(dB)
PHAS
EBA
LAN
CE(D
EG.)
QPSK PHASE BALANCE (RF = +5 dBm, I/Q = ±0.2V)
6.4 6.6 6.8 7.0 7.2 7.46.4 6.6 6.8 7.0 7.2 7.4
-90°
+90°
0°
-180°
SYS6474N01R
.437 [11.100]
S/N XXXXXX
M/N XXXXXX
MADE IN USAHAUPPAUGE, N.Y. 11788
1.850[46.99]
.375 [9.525]
.187 [4.750]
GPO(TYP. 2 PLACES)
1.600[40.64]
2.000 [50.80].150 [3.81] TYP.
.120 [3.048] TYP.
+5V
FAULT
+12V
Q
#2-56NC-2 THD THRU(TYP. 4 PLACES)
.400 [10.16]
1.925 [48.90].150 [3.81] TYP.
.075 [1.91] TYP.
.075[1.905]
LO
RF
I
.030 [.762] DIA X .250 [6.35] LG.(TYP. 5 PLACES)
2.000[50.80]
.187 [4.750]
1.600[40.64]
.400 [10.16]
1.2000[30.48]
1.000[25.40]
.800[20.32]
MATERIAL: KOVARMATERIAL: NICKEL
NOTE: All dimensions shown in brackets [ ] are in millimeters.
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
IF frequency range GHz 1.5 2.5
IF VSWR 50 ohm reference Ratio 2:1
Input power dBm 0
LO frequency range GHz 17.5
LO power range dBm -2 +2
LO VSWR 50 ohm reference Ratio 2:1
V+ bias voltage (Note 1) @ 1,600 mA max. +10
V- bias voltage (Note 1) @ 60 mA max. -9 -15
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
Conversion gain dB 30
Fundamental LO leakage @ RF output dBm -50
Leakage LO X2 @ RF output dBm 0
Leakage (with Option 1) dBm -60
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range GHz 36.5 37.5
RF VSWR 50 ohm reference Ratio 2:1
MODEL: SYSTX3638
FEATURES• IF frequency range ........... 1.5 to 2.5 GHz
• RF frequency range.......... 36.5 to 37.5 GHz
• Fundamental leakage ....... -50 dBm
• Packaging.......................... Hermetically sealed
INTEGRATED UPCONVERTER AND POWER AMPLIFIER
MAXIMUM RATINGSSpecification temperature .............. +25°COperating temperature .................... -55 to +65°CStorage temperature........................ -65 to +95°C
OUTLINE DRAWING
NOTE: Plus external bias board.All dimensions shown in brackets [ ] are in millimeters.
NOTE: Test data supplied at 25°C;output power, output frequency spectrum, bias current and voltage.
OptionsBPF 1. External RF bandpass filter
NOTE 1: Supplied with external voltage regulator board, with bias protection circuit.) PA2 + and -, and PA3 + and - voltages are derived from the +10, and -12 V supplies on the regulator board.Option 2: Supplied with all regulators internal to device–no external board.
SMA FIELD REPLACEABLECONNECTOR (TYP. 2 PLACES)
J3K OR SMA FIELDREPLACEABLECONNECTOR
1.37 [34.80]
J2
J3
LOIN
IFIN
+10
V
-15
V
PA
2+
PA
3+
PA
2-
PA
3-
VD
ET
RFOUT
1.170 [29.718]0.890 [22.606]
.100 [2.54]
0.24[6.10] 0.115
[2.921]0.12[3.05]
0.24 [6.10]
0.12 [3.05]
0.55[13.97]
1.08 [27.43]
0.27 [6.86]0.540
[13.716]
0.580[14.73]
0.250 [6.35]
0.320[8.128]
0.770[19.558]
MOUNTING SURFACESEE NOTE 1
4X #1–72 UNF X .120 [0.06] DPMTG HOLES
7X Ø.030 [0.76] X .25 [6.35] DPSOLDER TERMINALS
0.155 [3.937]0.380[9.652]
1.20 [30.48]
0.90 [22.86]1.05 [26.67]
0.75 [19.05]
0.42 [10.67]0.60 [15.24]
IF RF
SUBHARMONIC
MIXERIF INPUT
1.5 TO 2.5 GHz-3 dBm
RF OUTPUT36.5 TO 37.5 GHz
+25 dBm
LO/2 INPUT17.5 GHz
0 dBm
IMAGE FILTERPOWER
AMPLIFIERPOWER
MONITOR
VIDEOOUTPUT
LO
CU
STO
MPR
OD
UC
TS
485
486
CU
STO
MPR
OD
UC
TS
This page is intentionally blank
Revised:03/21/11
MODEL: SYS1840A24R
FEATURES• RF frequency range............ 18 to 40 GHz
• Low phase noise internal LOs
• Local/remote band switch
• Ruggedized case
• Input power ........................ 120 VAC
• Stable ovenized frequency reference
18 TO 40 GHz BLOCK DOWNCONVERTER
CUSTOM
PRODUCTS
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range Band 1 GHz 18 26Band 2 GHz 26 40
RF VSWR Ratio 2.5:1
Band select TTL pulse Volts 0 5
LO VSWR Ratio 2.5:1
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
Conversion gain Band 1 dB 3 6 9Band 2 dB 3 8 13
Single sideband noise figure 22
Fundamental LO leakage at IF 14 GHz dBm -52
Image rejection dB 35 15
Output power at 1 dB compression dBm 3
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.IF frequency range Band 1 GHz 2 10
Band 2 GHz 2 16Band indicator Band 2 = High Volts 0 5
IF VSWR TTL Ratio 2.5:1
The SYS1840A24R block downconverter is a dual-band downconverter with frequency coverage from 18 to 40GHz. It is suitable for use as a frequency extension for lower frequency test equipment. The internally generatedLO source features high frequency stability, and very low phase-noise. The unit also features a built-in AC powersupply, and electronic band switch that can be controlled by a front-panel switch, or via a remote control signal.An optional RF amplifier is available for low noise applications.
X342 GHz
FL226–40 GHzLP FILTER
FL118–26 GHzLP FILTER
14 GHz100 MHz OCXOREFERENCE
J1RF INPUT
FRONT PANEL2.9mm FEMALE
18-40 GHz
J2IF OUTPUT
FRONT PANELN FEMALE2–16 GHz
RF SWITCH
LO
MX1IF
2–10 GHz
IF2–16 GHz
IF LPF16 GHz AMP 1
RF
MX2
RF
X228 GHz
487
CON
VER
SIO
NG
AIN
(dB)
FREQUENCY (GHz)
18 TO 26 GHz BANDCONVERSION GAIN (dB) (IF = 2 to 10 GHz)
18 19.6 21.2 22.8 24.4 26 26 28.8 31.6 34.4 37.2 40
18 19.6 21.2 22.8 24.4 26 26 7.3 7.5 7.7 7.9 40
FREQUENCY (GHz)
26 TO 40 GHz BANDCONVERSION GAIN (IF = 2 to 16 GHz)
CON
VER
SIO
NG
AIN
(dB)
NO
ISE
FIG
UR
E(d
B)
FREQUENCY (GHz)
NOISE FIGURE (dB)
FREQUENCY (GHz)
NOISE FIGURE (dB)
NO
ISE
FIG
UR
E(d
B)
50
45
40
35
30
25
20
15
10
5
0
50
45
40
35
30
25
20
15
10
5
0
20
18
16
14
12
10
8
6
4
2
0
20
18
16
14
12
10
8
6
4
2
0
SYS1840A24R TYPICAL TEST DATA
MAXIMUM RATINGSSpecifications taken at ...................... +25°COperating temperature........................ -20 to +50°CStorage temperature .......................... -55 to +95°C
OUTLINE DRAWING
488
NOTE: Test data supplied at 25°C. Conversion gain, leakage, noise figure, image rejection, compression point.
NOTE: All dimensions shown in brackets [ ] are in millimeters.
Revised:03/21/11
CUSTOM
PRODUCTS
.13 [3.30]
.145 [36.83]2.24
[56.90]3.03
[76.96]
6.21[157.73]
7.23[183.64]
9.44[239.78]
1.08[2743]
14.95[379.73]
13.50[342.90]
12.00[304.80]
1.38[35.05] .73
[18.54]
2.17[55.12]
7.49[190.25]
EXHAUST
N TYPE(FEMALE)
TYPE 'K'FEMALECONNECTOR
IFO
UTP
UT
RF
INP
UT
BA
ND
SE
LEC
T
120VA
CP
OW
ER
GM
A-1A
FUS
E
BA
ND
RE
D/H
IGH
GR
EE
N/LO
W
CO
NTR
OL
CONNECTOR, POWER(TYPE DEM9P/MALE)
TOGGLESWITCHESMS35059-26MOMENTARY ACTION
6.00 [152.40] 7.31 [185.67]4.88 [123.95]
2.44[61.98]2.69
[68.33]
4.55 [115.57]10.00 [254.00]
AIR INTAKE
X6 Ø.28 [7.11]MOUNTING HOLE
MODEL: SYS1840N01R
FEATURES• RF frequency range.......... 18 to 40 GHz
• Conversion gain ............... 30 dB
• Noise figure....................... 7 dB
LOW-NOISE BLOCK DOWNCONVERTER
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range Band 1 GHz 18 26Band 2 GHz 26 40
RF VSWR Ratio 2.5:1
Reference select External Volts 5
Reference input 10 MHz dBm +3 +11
Power supply voltages +15 at .8A max. Volts 14.5 15.5-15 at .06A max. Volts -16 -9+9 at .8A max. Volts 8.7 10
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
Conversion gain dB 24 36
Single-sideband noise figure at 25°C dB 4 7
Fundamental LO leakage at IF 11 GHz dBm -55 -50
Image rejection dB 40
Output power at 1 dB compression dBm +5 +7
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.IF frequency range Band 1 GHz 7 15
Band 2 GHz 4 18
IF VSWR Ratio 2.0
Reference output 10 MHz dBm +4
The SYS1840N01R low-noise, block downconverter is a dual-band downconverter with frequency coverage from18 to 40 GHz. It is suitable for use as a receiver front-end for wideband systems, or frequency extension modules.An internally generated LO source can be commanded to lock to an internal 10 MHz reference, or to an external10 MHz reference for phase coherent applications. The internal 10 MHz reference is low phase-noise, ovenizeddesign and is available at a reference output connector. The RF band is selected via an external TTL input, forremote control applications. The unit is integrated into a 3” x 4” x 5.3” cube for ease of integration into an equip-ment chassis or antenna feed.
X444 GHz
FL226–40 GHzLP FILTER
FL118–26 GHzLP FILTER
11 GHz
10 MHz10 MHz
100 MHz OCXOREFERENCE
REFERENCECONTROL
J1RF INPUT
FRONT PANEL2.9mm FEMALE
J3RF INPUT
FRONT PANELSMA FEMALE
J2IF OUTPUTFRONT PANELSMA FEMALE4–18 GHz
J24REF OUTPUTFRONT PANELSMA FEMALE
COAX SWITCH COAX SWITCH
LO
AMP 1
AMP 2
MX1IF
7–15 GHz
IF4–18 GHz
AMP 3RF
MX2
RF
X333 GHz
Rev
ised
:05
/05/
11
CUSTOM
PRODUCTS
489
CON
VER
SIO
N G
AIN
(dB)
FREQUENCY (GHz)
18±26 GHz BandCONVERSION GAIN (dB) (IF = 7 to 15 GHz)
18 19.6 21.2 22.8 24.4 26 26 28.8 31.6 34.4 37.2 40
18 19.6 21.2 22.8 24.4 26 26 7.3 7.5 7.7 7.9 40
FREQUENCY (GHz)
26±40 GHz BandCONVERSION GAIN (IF = 4 to 18 GHz)
CON
VER
SIO
N G
AIN
(dB)
NO
ISE
FIG
UR
E (d
B)
FREQUENCY (GHz)
NOISE FIGURE (dB)
FREQUENCY (GHz)
NOISE FIGURE (dB)
NO
ISE
FIG
UR
E (d
B)
50
45
40
35
30
25
20
15
10
5
0
50
45
40
35
30
25
20
15
10
5
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
SYS1840N01R TYPICAL TEST DATA
MAXIMUM RATINGSSpecification temperature .................. +25°COperating temperature ........................ -40 to +70°C*Storage temperature .......................... -65 to +125°C*Unit to be mounted with thermal heatsink attached to base plate.
OUTLINE DRAWING
490
NOTE: Test data supplied at 25°C; conversion gain, noise figure, image rejection and compression point.
NOTE: All dimensions shown in brackets [ ] are in millimeters.
CU
STO
MPR
OD
UC
TS
J410
MH
z R
EF
OU
TPU
T
J310
MH
z R
EF
INP
UT J1
RF
INP
UT J2 IF
OU
TPU
T
J5
0.649[16.485]
3
0.138[3.505]
4.091[103.91]
3.815[96.90]
3.50[88.90]
0.296 [7.518]
1.88[47.75]
0
2.000 [50.80]
1.00 [25.40]1.21 [30.73]
1.84 [46.74]
2.16[54.86]
0.52[13.21]
1.51[38.35]
0.90[22.86]
4.00 [101.60]
5
0.27 [0.686] X .027 [0.686](4 PLACES)Ø 0.13 [Ø 3.30]
MOUNTING HOLE
3.00[76.20]
0.53[13.46]
0
0.43 [10.92]
2
5.30 [134.62]
0
MODEL: LNB-7181-02
FEATURES• Low noise figure
• Weatherproof design
• Bias provided through IF ports
• Low phase noise internal oscillator
• Internal crystal reference
X-BAND LOW-NOISE BLOCK CONVERTER
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range GHz 7.1 8.1
RF VSWR (RF = -10 dBm, LO = +13 dBm) Ratio 1.2:1
LO frequency range GHz 6.1
LO phase noise 1 kHz dBc/Hz -7010 kHz dBc/Hz -90
100 kHz dBc/Hz -1101 MHz dBc/Hz -120
LO accuracy -30 to +60°C kHz ±100
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
Conversion loss (IF = 100 MHz, LO = +13 dBm) dB 40
Single sideband noise figure at 25°C dB 1.3at 60°C dB 2
Image rejection dB 40
RF-to-IF isolation dB 80
Output power at 1 dB compression dBm +10
Output two-tone third order intercept point dBm +23
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.IF frequency range GHz 1 2
IF VSWR Ratio 1.5:1
The LNB-7181-02 is a weatherproof block converter offering very low noise figure and low phase noise. The out-put Bias-T allows bias voltage to be provided via the IF port cable. The unit is suitable for use at an antenna feedto preserve signal integrity.
RF IFLO
AMP216
J1RF INPUT
7.1 TO 8.1 GHzN-FEMALE
FLZ0096 DB0408 IF0102-LP-BIAST ASSY: 19493
J2IF OUTPUT1–2 GHz+10 dBm30IP: +20 dBm+15 V BIAS
491
CU
STO
MPR
OD
UC
TS
VSW
R (R
ATIO
)
FREQUENCY (GHz)
VSWR
7.1 7.3 7.5 7.7 7.9 8.1 7.1 7.3 7.5 7.7 7.9 8.1
7.1 7.3 7.5 7.7 7.9 8.1 7.1 7.3 7.5 7.7 7.9 8.1
FREQUENCY (GHz)
IMAGE REJECTION (dB)
IMAG
E R
EJEC
TIO
N (d
B)
CON
VER
SIO
NG
AIN
(dB)
FREQUENCY (GHz)
CONVERSION GAIN (dB)
FREQUENCY (Hz)
NOISE FIGURE (dB)
NO
ISE
FIG
UR
E (d
B)
1.5:1
1.45:1
1.4:1
1.35:1
1.3:1
1.25:1
1.2:1
1.15:1
1.1:1
1.05:1
1.0:1
70
65
60
55
50
45
40
35
30
25
20
2.0
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
65
60
55
50
45
40
35
30
25
20
15
LNB-7181-02 TYPICAL TEST DATA
MAXIMUM RATINGSSpecification temperature .................. +25°COperating temperature ........................ -30 to +60°CStorage temperature .......................... -65 to +125°C
OUTLINE DRAWING
AVAILABLE OPTION1. Other RF/LO frequency ranges.
492
NOTE: Test data supplied at 25°C; conversion gain, noise figure, image rejection and compression point.
NOTE: All dimensions shown in brackets [ ] are in millimeters.
CU
STO
MPR
OD
UC
TS
2.35[59.69]
3.54[89.92]
1.04 [26.42]
IF OUT+15V
RF IN
1.09 [27.69]
1.08 [27.43]
2.17[55.12]
4.54 [115.32]
5.24 [133.10]
MOUNTING HOLESM5 X 0.8 OPPOSITESIDE (2 PLACES)
N SERIES FEMALE CONNECTOR
4.05 [102.87]
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
Frequency range GHz 34 36
Input level dBm +4 +7
Input/output VSWR 50 ohm reference Ratio 2:1
V+ bias current @ +9 to +16 V A 2
V- bias current @ -9 to -16 V mA 150
Output power (factory preset) Control=”00” dBm +17Control=”01” dBm +20Control=”10” dBm +22Control=”11” dBm +27
Output power adjustment range (all states) dB 10
Switching speed usec. 20
493
MODEL: SYS3436N01R
FEATURES• High output level ................... +27 dBm
• Wide adjustment range.......... 10 dB
• Field adjustable
34 TO 36 GHz SWITCHED POWER AMPLIFIER ASSEMBLY
OUTLINE DRAWING
NOTES: 1. Unit’s mounting surface shall be attached to
a heatsink capable of dissipating the devices power consumption without exceeding the operating temperature limits.
2. Mass 413 grams typical.3. All dimensions shown in brackets [ ] are
in millimeters.
0.250 [6.35]
5.21 [132.33]
0.13 [3.30]
0.38 [9.65]
0.13 TYP. [3.30]
3.060 [77.72]
0.38 [9.65]
0.18 [4.57]
0.17 [4.32]0.37 [9.40]
0.91 [23.11]
1.30 [33.02]
4 X 4–40 UNC-2N0.170 [4.32] DEEP BOTH SIDES MATES WITH UG-599/U
0.50 [12.70]
0.265 [6.73]
0.530 [13.46]
0.500 [12.270]
0.13 [3.30]
1.00 [25.40]0.37 [9.40]3.40 [86.36]0.37 [9.40]
0.17 [4.32]0.18 [4.57]
0.38 [9.65]
0.17 [4.32]
TTL "00"ADJUST
+15V
-15V
TTL1
TTL2
GND
OUTIN
TTL "01"ADJUSTTTL "10"ADJUSTTTL "11"ADJUST
4.80 [121.92]
WAVEGUIDEWR-28BOTH SIDES
MOUNTINGSURFACE
TH4F TH4F
TH4FTH4F
CU
STO
MPR
OD
UC
TS
IN
TTL2
TTL "00"ADJUST
WR-28 WG
DRIVER ANTENUATOR POWER AMP
OUT
TTL "01"ADJUST
WR-28 WG
CONTROL/DRIVER
TTL "10"ADJUST
TTL "11"ADJUST
TTL1
The SYS3436N01R is a TTL-controlled switched power amplifier assembly with four preset output power states. Allfour output states are field adjustable over a 10 dB range. Applications include TWT driver and test instrumentation.
MAXIMUM RATINGSSpecification temperature .................. +25°COperating temperature ........................ -35 to +65°CStorage temperature .......................... -40 to +95°C
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range GHz 2 4
RF VSWR 50 ohm reference Ratio 1.8:1
V+ bias current @ +15 V mA 450
LO frequency range GHz 2.065 4.110
LO power range dBm +8 +11
LO VSWR 1.8:1
Switch control -5 VDC mA 0.01
+0.9 VDC mA 60
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
RF/IF path gain dB 5.25 6.75
Image rejection dB 20
Single sideband noise figure dB 11
RF coupled test port gain dB -12
Cross path isolation dB 60
Path switching time nsec 50
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
IF frequency range MHz 55 110
IF VSWR Ratio 1.25:1
MODEL: SYS0204N01R
FEATURES• Low system noise figure ...... 11 dB typical
• Fast switching ....................... 50 nsec typical
• Image rejection ...................... 20 dB typical
• Cross path isolation.............. 60 dB typical
• Fast blanking function.......... 10 nsec typical
2 TO 4 GHz LOW-NOISE MIXER PREAMPLIFIER WITH SELECTABLE INPUTS
494
CU
STO
MPR
OD
UC
TS
LO 1
S1
RF 1
RF 2
RF 3
S2 S3
IF 1A
IF 2A
IF 1C
IF 2B
IF 2C
IF 3A
IF 3B
IF 3C
IF 1B
LO 2 LO 3
The SYS0204N01R is an integrated low-noise converter with internal image filtering and a 3P2T RF input selectionswitch. All three RF inputs and IF outputs are simultaneously active and feature 60 dB of isolation between the paths.The switch activates within 50 microseconds and also features the ability to perform a blanking function at speedsas fast as 10 nanoseconds. RF signal test ports are provided for sampling the input signal to each mixer. Hermeticsealing is available for high reliability applications. Please contact MITEQ for more information.
MAXIMUM RATINGSSpecification temperature .................. +25°COperating temperature ........................ 0 to 50°CStorage temperature .......................... -40 to +71°C
NOTE: Test data supplied at 25°C;RF/IF path gain, image rejection and noise figure.
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range MHz 100
RF power range dBm 0
RF VSWR 50 ohm reference Ratio 1.5:1
V+ bias current @ +9 to +16 V mA 400
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
Phase noise SYS0118N01R100 Hz dBc/Hz -981 kHz dBc/Hz -10510 kHz dBc/Hz -107100 kHz dBc/Hz -1121 MHz dBc/Hz -13310 MHz dBc/Hz -150
(Note: Phase noise for other models varies, please contact MITEQ.)
Spurious dBc -50
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range SYS0118N01R GHz 1 18SYS0218N01R GHz 2 18SYS0318N01R GHz 3 18
RF power (1 GHz tone) dBm 0 -10
RF VSWR 50 ohm reference Ratio 1.5:1
Spectral flatness dB ±10
495
MODELS: SYS0118N01R, SYS0218N01R AND SYS0318N01R
FEATURES• Low frequency input ................ 100 MHz
• Flat output spectrum ............... ±10 dB typical
• High spurious-free dynamic range.......................... 50 dB typical
• Single DC supply...................... +12 VDC
1 TO 18 GHz COMB GENERATOR FREQUENCY MULTIPLIER
MITEQ has developed a line of comb generator multiplier products. Three models are available: SYS0118N01R,SYS0218N01R and SYS0318N01R, with output comb spacing of 1 GHz, 2 GHz and 3 GHz, respectively. Eachmodel accepts a 100 MHz input signal and produces a synchronous spectral comb. A fully integrated architecture isused to implement an internal phase-locked oscillator technique prior to exciting the multiplier, resulting in high spec-tral purity and low amplitude variation without degradation of the output signal-to-noise ratio. Options available area switched filter output for individual tone selection, higher output power and lower overall phase noise. Please con-tact MITEQ for more information.
PHASELOCK
MATCHINGNETWORK
MATCHINGNETWORK
COMBGENERATOR
AMPLITUDEEQUALIZER
1 GHz to 18 GHzCOMB
FREQUENCYDOUBLEROR TRIPLER(OPTIONAL)
100 MHzREF
1 GHzX2orX3
CU
STO
MPR
OD
UC
TS
SYS0218N01R TYPICAL TEST DATA
OUTLINE DRAWING
496
NOTE: All dimensions shown in brackets [ ] are in millimeters.
2XTYPE SMA FIELD REPLACEABLE FEMALE CONNECTOR
1.65 [41.9]
0.16 [4.1]0.47 [11.9]
0.27 [6.9]
1.85[47.0]
INPUTGND
OUTPUT
2.00[50.8]
0.06[2.00]
2X 0.38 [8.5]
6X M2.5 TAP0.25 [6.4] DP
FAR SIDE
0.63 [16.0]
3.00 [76.2]2.75 [68.8]
2.50 [63.5]1.75 [44.5]
1.50 [38.1]0.25 [6.4]
0.35 [8.9]
1.00 [25.4]
CU
STO
MPR
OD
UC
TS
-60-70-80-90
-100-110-120-130-140-150-160-170-180
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-1000.5 2.3 4.1 5.9 7.7 9.5 11.3 13.1 14.9 18.516.7 5.75 5.8 5.85 5.9 5.95 6 6.05 6.1 6.15 6.256.2
100 K 1 M 10 M 100 M
2
OU
TPU
T SP
ECTR
UM
(dB)
PH
ASE
NO
ISE
(dBc
/Hz)
FREQUENCY (GHz)
OUTPUT SPECTRUM
FREQUENCY (GHz)
REFERENCE SPURIOUS
FREQUENCY (Hz)
PHASE NOISE
REF
EREN
CE S
PUR
IOU
S (d
B)
MAXIMUM RATINGSSpecification temperature .................. +25°COperating temperature ........................ -40 to +70°CStorage temperature .......................... -55 to +85°C
NOTE: Test data supplied at 25°C; per output spectrum data.
497
MODEL: SYS0518N01R
FEATURES• Dual conversion architecture for
high spur rejection
• LO or RF-to-IF isolation.................. 70 dB
0.5 TO 18 GHz BROADBAND CONVERTER
OUTLINE DRAWING
NOTE: All dimensions shown in brackets [ ] are in millimeters.
4.00[101.60]
8.00 [203.20]
SYS0518N01R
CU
STO
MPR
OD
UC
TS
BLOCK DIAGRAM
The SYS0518N01R is a dual conversion receiver capable of translating any 4 GHz instantaneous bandwidth in the0.5 to 18 GHz RF input range to an IF center frequency of 6 GHz. By using a high side LO and MITEQ’s broadbandTB0440LW1 mixer for the first conversion, it allows image frequencies to be easily filtered without the use of a track-ing filter architecture, and allows for high image suppression not achievable from an image rejection mixer. The unitalso offers high image rejection and RF-to-IF and LO-to-IF isolation of 70 dB.
24.5-38.5 GHz
RFINPUT
0.5-18 GHz
IFOUTPUT8-12 GHz
BW=4.5 GHz
TB0440LW1 TB0440LW1
I RL
32 GHz
Fc=22 GHz
R IL
• Image rejection................................ 70 dB
• Conversion gain .............................. 20 dB
MAXIMUM RATINGSOperating temperature ........................ -20 to +60°CStorage temperature .......................... -40 to +95°C
MODEL: SYS9.0N01R
FEATURES• RF input frequency ...................... 9.31 GHz ±30 MHz• Conversion gain ........................... 83 dB• Gain control range ....................... 80 dB• Noise figure................................... 7 dB• Input compression point ............. +10 dBm• Front-panel phase and amplitude adjust for each channel
THREE-CHANNEL X-BAND MONOPULSE RADAR RECEIVER
498
CU
STO
MPR
OD
UC
TS
OUTLINE DRAWING
NOTE: All dimensions shown in brackets [ ] are in millimeters.
2.50 [63.50]3.35 [85.09]
5.56 [141.22]
0.25 [6.35]
2.44 [61.98]
2.04 [51.82]
3.25 [82.55]
2.39 [60.71]
1.83 [46.48]1.25 [31.75]0.75
[19.05]
J6
3.31 [84.07]
3.69 [93.73]
4.23 [107.44]
2.50 [63.50]
4.00 [101.60]
1.44 [36.58]
1.88 [47.75]
0.99[25.15]
4.31[109.47]
2.94[74.68]
4.00[101.60]
2.50[63.50] J4
J7
1.56[39.62]
0.88[22.35]
0.88[22.35]
J5
J1J3
J2
J9J10
VID
EO
VID
EO
EL
GA
ING
AIN
SU
M
PH
AS
EE
L
NO
RM
AL
AD
JUS
T
J8
PH
AS
EA
Z
NO
RM
AL
GA
IN
PO
WE
R
AZ
VID
EO
A
AD
JUS
T
1.75[44.45]
2.09[53.09]
0.63[16.0]
3.80 [96.52]0.22[5.59]
0.22[5.59]
4.56[115.82]
4.10[104.14]
2.50[63.50]
0.90[22.96]
J17
J14
J16
J13
J15
J18
J12
J11
BLOCK DIAGRAM
The SYS9.0N01R is an integrated three-channel monopulse radar receiver front-end for use in receiving signal fora tracking radar system. The channel boasts an 80 dB gain control range to provide tracking over long distances.Internal phase adjusting circuits allow each channel to be phase matched in the system via front panel control. Theunit has built-in test circuits to verify mixer diode performance and to test injection RF signals. Both detected logvideo, and linear IF outputs are provided. Internal LO and test port injection splitters are provided with phasematched performance. The units are screened under high vibration and thermal cycling for high reliability.
45°
ADJ DRIVER
0-360° ANALOGADJUST VOLTAGE
90°OFFSET
135 MHz – 185 MHzIF OUTPUT
VIDEO OUTPUT
1
I
Q
IN OUT
I
Q
RF TESTSIGNAL INPUT
TESTPORT
SPLITTER
RF INPUT SUM
RF INPUT AZ
RF INPUT EL
LOINPUT
GAIN CONTROLINPUT
3-WAYLO
SPLITTER
VGC1 VGC2 VGC3 VGC4 VGC5
VGC1
VGC DRIVER
VGC212345
R IL
MAXIMUM RATINGSOperating temperature ........................ -40 to +65°CStorage temperature .......................... -62 to +71°C
• BIT circuits for fault-detection• Rugged packaging to withstand high
vibration and temperature range• High reliability screening
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
RF frequency range GHz 10 15RF VSWR 50 ohm reference Ratio 2:1V+ bias current @ +15 V 600V- bias current @ -15 V 50
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.
Conversion gain dB 5Power control range dB 10Spurious/harmonic output level dBc -70Minimum output capability dBm +13
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.
IF frequency range GHz DC 0.5
IF VSWR Ratio 2:1
499
MODEL: SYS1015N01R
FEATURES• Two medium power amplified channels• Integrated mixer to measure difference frequency• Integrated prescaler to measure absolute
frequency using a low frequency DSP• Integrated power control for output leveling
DUAL-CHANNEL SIGNAL PROCESSOR ASSEMBLY
BLOCK DIAGRAM
DRIVER
GAIN CONTROL
LVTTL
RF1 IN
RF2 IN
COUNTERSELECT
LVDSOUTPUT
PRESCALER
BPF
FL2
ƒ/256
DC4
LINEARIZERDET
RL I
LINEARIZER
DETECTED OUTPUT
RF1 OUT A/B
DELTA-F OUTDC to 500 MHz-30 dBm MIN.
RF2 OUT
CU
STO
MPR
OD
UC
TS
The SYS1015N01R is an integrated dual-channel signal processor for use in processing LOs in a microwave sys-tem. Integral gain control, power detector, mixer, and prescaler are used to control signal output power and monitorfrequencies using lower frequency DSP technology. The unit is constructed for higher volume applications with sur-face mounted printed circuit boards designed for automated assembly.
RF2
RF1
P1 P2
RF2
DELTA-F
RF1A
RF1B
SYS1015N01R
MAXIMUM RATINGSSpecification temperature ...... +25°COperating temperature ............ 0 to 50°CStorage temperature .............. -20 to +65°C
500
CU
STO
MPR
OD
UC
TS
This page is intentionally blank
501
ELECTRICAL SPECIFICATIONS
INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.RF frequency range Band 1 GHz 18 26
Band 2 GHz 26 40RF VSWR 50 ohm reference Ratio 2.8:1V+ bias current @ +9 to +16 V mA 450V- bias current @ -9 to +16 V mA 30LO frequency range Band 1 GHz 17
Band 2 GHz 21LO power range dBm +10 +12 +14LO VSWR 2.5:1
TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX.Conversion loss dB 14 18Image rejection dB 12 20Input 1 dB compression point dBm +5Input third-order intercept point dBm +15Fundamental LO leakage at IF port 17 and 21 GHz dBm -85 -75LO leakage at RF port 34 and 42 GHz dBm -30 -20
OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.IF frequency range Band 1 GHz 8 16
Band 2 GHz 2 16IF VSWR Ratio 2:1
MODEL: SYS0216N01R
FEATURES• 18–40 GHz frequency coverage
integrated aluminum housing
INTEGRATED DUAL-CHANNEL BLOCK CONVERTER
OUTLINE DRAWING
NOTE: All dimensions shown in brackets [ ] are in millimeters.
2.50 [63.50] Ø0.11 [2.79] THRU 4 PLACES
17 GHzIN
21 GHzIN
26-40 GHzIN
18-26 GHzIN
-V
+V
GND
8-16 GHzOUT
2-16 GHzOUT
0.49[12.45]
1.90 [48.26]
3.00[76.20]
2.80[71.12]
0.10[2.54]0.60 [15.24]
CU
STO
MPR
OD
UC
TS
The SYS0216N01R is an integrated dual-channel millimeter-wave block converter with internal filtering and LO multipliers. Theunit is used to convert signals in the range of 18–40 GHz down to 2–16 GHz. The unit will also function as an upconverter.Internal LO filtering significantly reduces fundamental LO leakage. High side LO and RF filtering provides full band imagerejection of 20 dB typical. The unit is integrated in a channelized aluminum housing for small size and high spurious isolation.An optional mounting plate with low-noise RF amplifiers is available to function as a low noise block converter.
X2
RFINPUT
26-40 GHz
RFINPUT
18-26 GHz
IFOUTPUT2-16 GHz
IFOUTPUT8-16 GHz
LO21 GHz
LO17 GHz
2
IMAGEFILTER TB0440LW1
IMAGEFILTER TB0440LW1
R IL
X2
34 GHz
42 GHz
R IL
BLOCK DIAGRAM
VSW
R (R
ATIO
)
RF FREQUENCY (GHz)
BAND 1BAND 2
BAND 1BAND 2
BAND 1BAND 2
BAND 1BAND 2
RF VSWR BAND 1 AND 2
18 19 21 22 24 26 42 44 46 48 50
8 1210 119 13 14 159 12.5010.75 14.25
16
40 42.5 45 47.5
BAND 2
5026 28 31 34 37 40
18 19 21 22 24 262 3.75 5.5 7.25 1626 28 31 34 37 40
RF FREQUENCY (GHz)
IMAGE REJECTION BAND 1 AND 2
IMAG
E R
EJEC
TIO
N (d
B)
CON
VER
SIO
N L
OSS
(dB)
RF FREQUENCY (GHz)
CONVERSION LOSS BAND 1 AND 2
IF FREQUENCY (GHz)
IF VSWR BAND 1 AND 2
VSW
R (R
ATIO
)
6:1
5:1
4:1
3:1
2:1
1:1
32
24
16
8
0
6:1
5:1
4:1
3:1
2:1
1:1
0
2
4
6
8
10
12
14
16
18
20
BAND 2
BAND 1
BAND 1
BAND 2
BAND 1
BAND 2 BAND 1
SYS0216N01R TYPICAL TEST DATA
OPTIONAL LNB OUTLINE DRAWING* OPTIONAL LNB BLOCK DIAGRAM*
2.50 [63.50]
17 GHzIN
21 GHzIN
26-40 GHzIN
18-26 GHzIN
LNA
LNA
-V
+V
GND
8-16 GHzOUT
2-16 GHzOUT
0.61[15.49]
I
4.11 [104.39]
2
X2
RFINPUT
26-40 GHz
RFINPUT
18-26 GHz
IFOUTPUT2-16 GHz
IFOUTPUT8-16 GHz
LO21 GHz
LO17 GHz
IMAGEFILTERLNA
LNA
TB0440LW1
IMAGEFILTER TB0440LW1
R IL
X2
34 GHz
42 GHz
R IL
000
NOTE: All dimensions shown in brackets [ ] are in millimeters.* Contact MITEQ for LNB option ordering information and specifications.
MAXIMUM RATINGSSpecification temperature .............. +25°COperating temperature .................... -40 to +65°CStorage temperature........................ -65 to +95°C
NOTE: Test data supplied at 25°C;conversion gain, image rejection, noise figure and output 1 dB compression point.
CU
STO
MPR
OD
UC
TS
502
503
MIXER SUBSYSTEMS
Questions and Answers about...
MIXER SUBSYSTEMS
Q1: How does the Mixer Product Department define a mixer subsystem?
A1: Generally, the subsystem consists of one or more unique core mixer products from catalog sections 1 through4, with added input or output components (such as amplifiers, filters, etc.) or simply phase and amplitude matchedgroups of the core mixer product with associated power dividers for LO, RF or IF.
Q2: What advantages do the subsystems offer the customer?
A2: Subsystems or multifunction components in general are designed to customer specifications. They offer thecustomer guaranteed input/output performance without worry about the ever-present interface problems between theindividual system building blocks. By eliminating intermodule connections, the units offer smaller size and light weightalternatives to assembled connectorized or drop-in components. These multifunction modules utilize, in addition to themixer capability, our low-noise amplifier technology and our high performance, small size frequency sources. In addi-tion, limiters, switches, filters, couplers, etc., can be incorporated to satisfy the customer’s requirements. Special mul-tichannel assemblies can also be produced in gain and phase matched modules.
Q3: How are the mixer subsystems grouped in this portion of the catalog?
A3: Generally, by market and complexity, because the final cost factor influences how the integration of the sub-system is accomplished. For example, all communication subsystems are intended to lower the overall cost consis-tent with meeting minimum standards of performance, whereas the radar and military subsystems tend to emphasizesmall size with screened components and state-of-the-art performance at fair prices.
Q3.1: How does MITEQ define millimeter-wave products?
A3.1: The millimeter-wave frequency band is generally accepted to mean from 30 to 300 GHz (1 mm to 0.1 mmwavelengths). For our purpose, however, in this section of the catalog, most products cover up to 50 GHz range.Furthermore, these products tend to utilize the MITEQ core technical advantages of: low-noise RF amplifiers, widestinput and output bandwidth mixers, phase-stable oscillators and multipliers.
Q3.2: What are the core advantages of Special Mixer Department’s millimeter-wave products?
A3.2: MITEQ offers the widest input/output bandwidth millimeter-wave up- and downconverters. The most populartriple-balanced unit is TB0440LW1 with an RF and LO bandwidth of 4 to 40 GHz and an IF bandwidth of 0.5 to 20GHz. Even-harmonic units are also available with less IF bandwidth, but require an LO of only 2 to 20 GHz to down-convert the 4 to 40 GHz, with only 1 to 2 dB higher loss than fundamental mixing. Another key advantage of ourdepartment’s mixer products is the capacity to integrate the low-noise amplifiers of other MITEQ departments into asingle-interface compensated unit.
The principal market for these products is low-noise block up- and downconverters that allow theuser to perform operations at high frequencies utilizingexisting lower frequency equipment.
The following plot shows the current capability ofMITEQ’s low-noise amplifiers in this frequency range.C
USTO
MPR
OD
UC
TS
LNA AMPLIFIERS NOISE FIGURE VS. FREQUENCY MODERATE BAND AMPLIFIERS
FREQUENCY (GHz)
4
3
2
1
440
290
170
75
4032241681
NO
ISE
FIG
UR
E d
B)
NO
ISE TEMPER
ATUR
E (K)
MIXER SUBSYSTEMS (CONT.)
Q3.3: What factors influence the choice of high or low side LO placement in wideband millimeter-wave block converters?
A3.3: Generally, one tries to eliminate extra LO x RF mixing products that combine the fundamental RF with har-monics of the LO. These products are highest in level and are also independent of the RF power. For example, the3LO-RF and 2LO-RF are typically -10 and -25 dBc, respectively, below the desired LO-RF output. In general, for widebandwidth applications, the LO harmonic mixing products are much more likely to occur with low side mixing. Forother applications, where LO x RF spurious products are not an issue, one may want to avoid the spectral inversionof low side mixing by placing the LO above the RF. High side mixing is also frequently employed to eliminate theimage response of a wideband receiver without tracking filters. However, another fixed frequency mixer and LO isnecessary to make this “dual conversion” technique function. The first double-sideband mixer, IF output is chosenhigh enough in frequency to produce an image band that falls outside the input RF range. For example, with a 2 to18 GHz RF input and tracking 24 to 40 GHz LO, the IF is fixed at 22 GHz and the image (2LO - RF) is 46 to 62 GHz.A second mixer and LO would be required to downconvert the 22 GHz first IF to perhaps 1 GHz. Caution is neces-sary, of course, to reject the image response of the second mixer at 20 or 24 GHz, but this is easier with a fixed fre-quency relative to the problem of a multioctave input. The first DSB mixer for this application can be a MITEQTB0440LW1.
Q3.4: How can undesired M x N (LO x RF) spurious products be minimized for a given application,assuming that “high side mixing” and LO power are not options?
A3.4: Triple-balanced mixers traditionally yield the lowest level spur products provided that the diode quads and cir-cuit baluns are constructed to yield high interport isolation. Restricting the RF and IF operating bandwidths will alsoeliminate many spur products, provided that out-of-band signals are also filtered. The table below shows the maxi-mum possible input RF, percentage bandwidth possible before certain low order products occur. Both fixed LO oper-ations above or below the RF band are shown, each with an octave IF output bandwidth for comparison (reference =Microwave Journal - 1990)
One can see from the above table that progressively smaller RF bandwidths are required to completely avoid certainproducts. The maximum RF bandwidth is also restricted to no more than 40% for the specific case of octave IF band-width. This also avoids any overlapping of the input and output bandwidth.
Q3.5: How are the general principles of the previous questions and answers applied to a specificmillimeter-wave example?
A3.5: Figure 1 illustrates several 26 to 40 GHz block downconverters, each for the 4 to 18 GHz output band. Thespur tables associated with each LO configuration illustrate the advantages of “high side” LO mixing to avoid LO har-monic products. In addition, an octave output bandwidth mixing configuration is shown that utilizes the previous prin-ciples of reduced bandwidths to eliminate spurs. However, three separate LOs and preselectors are required. Seethe following page for Figure 1.
504
MAXIMUM RF INPUT (PERCENTAGE BW) FOR “BLOCK DOWNCONVERTERS” TO AVOID CERTAIN M X N(LO X RF) SPURIOUS PRODUCTS (FOR CASE OF OCTAVE OUTPUT IF BANDWIDTH AND NO RF/IF BAND
OVERLAP)
CONDITIONS LO X 2RF 2LO X RF 2LO X 2RF 2LO X 3RF 3LO X 2RF 3LO X 3RF
LO > RF
IF BW = 0.20 0.40 0.40 0.15 0.40 0.43
0.66 (octave)
LO < RF
IF BW = 0.40 0.20 0.40 0.40 0.15 0.43
0.66 (octave) CU
STO
MPR
OD
UC
TS
505
MIXER SUBSYSTEMS (CONT.)
Spurious in-band responses for 26 to 40 GHz downconverter:
A. Block downconverter (LO < RF)
B. Block downconverter (LO > RF)
C. Multiple LOs with filters
A. INVERTING BLOCK DOWNCONVERTER LO < RF
B. NONINVERTING BLOCK DOWNCONVERTER LO > RF
C. THREE-BAND FILTERED BLOCK DOWNCONVERTER LO > RF
CU
STO
MPR
OD
UC
TS
FIGURE 1
LO = 35 GHz 39 GHz 43 GHz
IF 4 – 8 GHz
(octave)
RF 27 – 31 GHz 31 – 35 GHz 35 – 39 GHz
(m) RF x (n) LO IF = 4 – 18 GHz, LO = 35, 39, 43 GHz
FREQUENCY (GHz)
1 x 11 x 21 x 32 x 12 x 22 x 33 x 13 x 23 x 3
24 28 32 36 40
LO = 44 GHz
IF 4 – 18 GHz
RF 26 – 40 GHz
(m) RF x (n) LO IF = 4 – 18 GHz, LO = 44 GHz
FREQUENCY (GHz)
1 x 11 x 21 x 32 x 12 x 22 x 33 x 13 x 23 x 3
24 28 32 36 40
LO = 22 GHz
IF 4 – 18 GHz
RF 26 – 40 GHz
(m) RF x (n) LO IF = 4 – 18 GHz, LO = 22 GHz
FREQUENCY (GHz)
1 x 11 x 21 x 32 x 12 x 22 x 33 x 13 x 23 x 3
24 28 32 36 40
MIXER SUBSYSTEMS (CONT.)
Q4: What are some examples of new mixer subsystems useful to the communication engineer?
A4: Sampling mixers (Model SRD0218LW4) are becoming more prevalent in compact receivers and phase-locked frequency sources because they do not require a high power microwave LO to downconvert the desired sig-nal to a low IF frequency. I/Q sampling mixers can also be used for direct demodulation of biphase signals.
In addition, a new triple-balanced Schottky mixer allows direct multioctave block downconversion of the millimeter-wave 20 to 40 GHz band into an existing 0.5 to 20 GHz receiver. This is possible by using the TB0440LW1 mixer anda MITEQ-fixed frequency (+10 dBm) LO above or below the band of interest. This mixer is also useful for upcon-verting the 0.5 to 18 GHz band into a fixed Ku-band second converter, thus eliminating the image response withouttunable filters.
Q5: What are the basic principles of passive direction finding?
A5: The block diagram below shows a method of measuring the phase angle difference between signals reach-ing amplifiers A and B. All amplitude variations are removed by the IF limiters so the system is relatively insensitiveto channel gain differences. A low DC offset double-balanced mixer is used to measure the phase difference, butsince the mixer provides the same output voltage for two different phase angles, there is a 180 degree ambiguity inthe measurement.
Alternately, one can use an I/Q phase correlator or demodulator to resolve the ambiguity. The I/Q outputs can be usedto form a convenient polar display of a received angle. I/Q phase correlators are available at microwave and lowerfrequencies, although the accuracies are usually higher over narrow bandwidths below 1 GHz.
506
PHASEDETECTOR
INPUTSIGNAL
D SIN fl
PHASE DIFFERENCES = ψ = -2πD
SIN Ø
fl
MITEQ PDL SERIES
LIM
LIM
LOCALOSC
B
A
λ
D
fl
fl
fl
0°3 dB
Ø
K COS Ø
K SIN Ø
R
MITEQ DPD SERIES
L
R
L
AMP
LIM
LIM
Term Zo
Term Zo
AMP90°3 dB
CU
STO
MPR
OD
UC
TS
507
MIXER SUBSYSTEMS (CONT.)
Actual DF systems use pairs of antennas in the horizontal plane (azimuth) and vertical (elevation) plane. In addition,a fifth channel is sometimes used to resolve angular ambiguities. Frequently the antenna bandwidths are less thanthe receivers, so that input switching is required. The receiving must also be protected from high input power. Theblock diagram below illustrates a MITEQ five-channel catalog direction finding subsystem less the I/Q phase detec-tors (see MITEQ Model DSS Series).
CU
STO
MPR
OD
UC
TS
J3
J15
121751
J6BAND 2
CHANNEL D
BAND 3IF OUTPUT CHANNEL D
FL4 FL-LP
PA4 PHASE ADJ
AR6 AT4 GAIN ADJ
AR11SW4
J5
J17
121751
J10BAND 2
CHANNEL C
BAND 3IF OUTPUT CHANNEL C
FL3 FL-LP
PA3 PHASE ADJ
AR5 AT3 GAIN ADJ
AR10SW3
J2
J14
121751
J7BAND 2
CHANNEL B
BAND 3IF OUTPUT CHANNEL B
FL2 FL-LP
PA2 PHASE ADJ
AR4 AT2 GAIN ADJ
AR9SW2
J1 SW
J13
PHASE AND GAIN BOARD, 121751
J6BAND 2
CHANNEL A
BAND 3IF OUTPUT CHANNEL A
FL1 FL-LP
PA1 PHASE ADJ
AR3 ATI GAIN ADJ
AR8SW1
INPUT
120519
LO1 INPUT
LO2 INPUT
EXTERNAL ADJUST (TYPICAL 5 PLACES)
EXTERNAL ADJUST (TYPICAL 5 PLACES)
J4
J16
121751
J9BAND 2
CHANNEL E
BAND 3IF OUTPUT CHANNEL E
FL5 FL-LP
PA5 PHASE ADJ
AT5 GAIN ADJ
AR12SW5
TO CONTROL B0
TO CONTROL B0
TO CONTROL 80
TO CONTROL B0
TO CONTROL B0
DC2
LO1 LO2
DC1
AR7
BLO2 BLO1
AR2 AR1
D C T B A
M/N
SA
0502C06B
RF
PR
OC
ES
SO
R
S/N
XX
XX
XX
3.875.250
6.125
5.625
.250
.171 DIA THRU (6 HOLES)
2.812
PHASE ADJGAIN ADJ
J11 J10 J12
J6 LO1 J7 LO2
J9 J8
3.325
4.375
CONN, RF SMA FEMALE
IF OUTPUTS: CONNECTOR: RF SMA FEMALE (5 PLACES)
MIXER SUBSYSTEMS (CONT.)
Q6: Can the basic direction finding receiver be used to also measure incoming frequency?
A6: Yes, by first encoding the received signal into two separate outputs that have a phase difference in direct pro-portion to their frequency:
A large cable length difference in the two splitter outputs will yield rapidly varying phase with frequency. If these out-puts are applied to a two-channel DF system, the output phase difference, together with knowledge of the encodercable lengths, can be used to determine input frequency. This is the basic principle of an instantaneous frequencydiscriminator (IFM). In actual practice, several frequency encoders are used with progressively greater frequency res-olution, much in the same manner that one reads the dials of a gas or electric meter.
Q7: What advantages do sampling mixers offer relative to conventional mixers/LOs for ELINT(Electronic Intelligence Gathering) receiver designs?
A7: Basically, lower cost and power consumption, because the sampling mixer utilizes a UHF LO with internalpulse shaping from a step recovery diode to downconvert an RF at 1 to 20 times higher in frequency. The samplingmixer diodes only charge for a short instant, thus requiring low LO energy relative to the amplifier multiplier chain usedto generate the LO power required for a conventional fundamental mixer. The sampling mixer, however, has a limiton the maximum IF bandwidth equal to one half the applied LO frequency (owing to the repetitive frequency responseof this mixer). Sampling mixers can also be made in I/Q and image rejection configurations (see Q & A in phase detec-tor section).
Q8: What is meant by electronic warfare (EW) components?
A8: These are component groups that are used in systems that identify and defeat the goals of ground and mis-sile radar systems. A typical component pair might be an I/Q downconverting mixer and upconverting modulator thatalters some amplitude or frequency property of a received radar pulse and then retransmits it to act as a decoy reflec-tion. In addition, since EW systems must protect the host vehicle from many different frequency signals with quickreaction times, the operating subsystem bandwidths are wide (often 0.5 to 18 GHz). Airborne EW systems frequent-ly employ small size multiple mixers with a common output or second-stage processing receiver.
508
MITEQ IQM SERIES
FREQ.TO PHASE ENCODING, CABLE LENGTH
RF INPUT
0°3 dB
90°3 dB
K SIN Ø
K COS Ø
R
L
R
L
LIM 0°3 dB
VERT.HORIZ.
CU
STO
MPR
OD
UC
TS
509
MIXER SUBSYSTEMS (CONT.)
Q9: What precautions are necessary when purchasing front-end mixer components for radarreceivers?
A9: If the mixer could be subjected to high peak power from transmitter leakage, one must use an input pin diodelimiter to ensure that no more than approximately 50 mW/diode or +23 dBm per quad average power. This limit isbased upon an average thermal resistance of 160°C/watt for a diode quad mounted on a soft suspended circuit boardand maximum diode junction temperature of 125°C with an ambient temperature of 85°C. A single diode limiter avail-able on most MITEQ mixer/preamplifiers will provide protection against a 100 peak power 1 µs pulse and 1 watt aver-age power.
Q10: What choice of front-end components will maximize the dynamic range of radar receivers?
A10: The benefits of low-noise MITEQ AFS or AMF RF preamplifiers are well known and obvious in detecting min-imum signal levels. However, the maximum input signal level is often limited by the second-stage image rejectionmixer’s 1 dB compression level. A general rule of thumb for the 1 dB compression level of any Schottky barrier mixeris 5 dB less than the LO power. Therefore, if the maximum output power level of the RF preamplifier is +10 dBm, onewould need at least a +15 dBm LO power mixer to avoid restricting the dynamic range. A four-channel radar receiv-er would then require a total of +21 dBm or more LO power. The additional cost and excess noise of the required LOamplifier will impose more design restrictions. As an alternative, a MESFET image rejection mixer generally has anRF 1 dB compression point equal to the LO power, therefore, in this case, the total LO power required is +16 dBm.
The MITEQ Model ARS0506L is an example of a high dynamic range four-channel front end including the LNAs MES-FET IR mixers, IF amplifiers and matched filters. The noise figure is typically 4 dB, but, could also handle up to +5dBm of input broadband RF noise jamming before overloading. The IF filters used in this phase and amplitude trackedfront end have uniform group delay, thus ensuring that paired echoes are at least 40 dB below the main response.
CU
STO
MPR
OD
UC
TS
510
MILLIMETER-WAVE BLOCK CONVERTERS
A unique method has been developed for extendingthe frequency of existing 20 GHz broadband systemsto cover the entire 26 to 40 GHz Ka-band without theneed of a tuned front-end architecture. The ModelsLNB-2640-40 and LNB-1826-30 low-noise block (LNB)converters are combined to accept inputs over the 18to 40 GHz frequency range and block convert the fullband into the 2 to 20 GHz range, as shown in Figure 1.All of the converters’ filtering and LOs are internal,including a phase-locked LO source that can belocked to an external 10 MHz reference.
With the recent proliferation of both commercial andmilitary applications throughout the Ka-band, a signif-icant need has arisen for frequency conversion equip-ment to cover these now-popular ranges. Hardwarerequirements in support of these applications includenot only the technology embedded in the systems,but also the supporting test equipment required toalign, maintain and install the developed hardware.
With commercial applications such as 38 GHz point-to-point radios generating interest in high volume, lowcost production, the obvious solution is to developcustom MMICs with millimeter-wave functions. Thiseffort is already in place at many of the large foundryoperations with 0.25 or 0.18 µm GaAs processes.Amplifier, mixer and multiplier blocks have beendeveloped and currently are being integrated to offercomplete application-specific transceiver modules atreasonable prices. Even military applications, such as35 GHz monopulse seekers, can support enough vol-ume to justify a custom MMIC development effort andare often satisfied by this route.
Although millimeter-wave MMIC technology has astrong foothold throughout the Ka-band, a host ofrequirements exist on the periphery of these volumeapplications that require more broad-based perfor-mance modules. These periphery applicationsincrease the need for broadband block conversionsystems, as shown in Figure 2.
FIGURE 2
APPLICATIONSBroadband block conversion is suitable for the testand measurement market, as well as for electronicwarfare (EW) and electronic intelligence (ELINT) sys-tems that are used to extend existing equipmentoperation into the low millimeter-wave bands.Spectrum analyzers operating from 10 kHz to 26 GHzhave been on the market for several years. The ana-lyzers are found in almost every microwave companyin the world and, unfortunately, are obsolete to userswho are shifting their focus to the higher frequencybands. An obvious solution to the reprocurement ofsuch costly test equipment is to provide an adjunctsubsystem that can easily extend the frequency ofthis existing equipment to cover the desired frequen-cy bands.
Currently, most spectrum analyzer companies offerexternal harmonic mixers to extend the performanceof their fundamental operating frequency range.However, these harmonic mixers have always beencumbersome to use, often requiring a swept LO totune the desired signal into the narrow IF band of themixer. A similar situation has also existed in broad-band military systems. Presently, thousands of field-ed electronic countermeasure and ELINT systemsare operating over the 0.5 to 18 GHz band. Twochoices are available to provide operation into Ka-band, including developing a full-up, tuned Ka-bandsystem to cover the entire frequency range from 18 to40 GHz, and adding an adjunct subsystem to theexisting system to cover only the specific narrowbands above 18 GHz.
In both applications, the ideal solution would be tofold the entire upper band into the existing lower bandto relieve the requirement for a tuned front end. This
A 26 TO 40 GHzBLOCK FREQUENCY CONVERSION
OUTPUT FREQUENCY
RANGE
FREQUENCY (GHz)
INPUT FREQUENCY
RANGE
LO
424026162
BROADBAND BLOCK CONVERSION APPLICATIONS;(a) SPECTRUM ANALYZER AND
(b) EW SYSTEM FREQUENCY EXTENSIONS
2 – 16 GHzLNB-2640-4026 – 40
GHz EXISTING SPECTRUM ANALYZER
10 MHz REFERENCE
OUTPUT
EXISTING BROADBAND EW
RECEIVER
LNB-2640-4026 – 40 GHz
LNB-1826- 3018 – 26 GHz
0.5– 18 GHz
(a)
(b)
FIGURE 1
CU
STO
MPR
OD
UC
TS
511
CU
STO
MPR
OD
UC
TS
MILLIMETER-WAVE BLOCK CONVERTERS
technique satisfies the requirement for minimizingadditional hardware and the logistical impact of oper-ating an additional system in the upper band. Usingblock conversion, all of the processing of the lowerbands can be utilized throughout Ka-band with mini-mal modifications, which consist mainly of a simplefrequency offset.
BLOCK CONVERSION
Folding an entire frequency range into another is alsoknown as block frequency conversion or block con-version. The process requires only a fixed LO. Moreimportantly, the process also requires a mixer with anIF coverage that matches the bandwidth of the RFband. This IF bandwidth limitation had been the long-standing reason why this approach was never utilizedfor Ka-band. A production-level mixer that could oper-ate with an RF range from 18 to 40 GHz with an IFrange to 20 GHz was all that was required.
MIXER ADVANCES
Mixers have long been available in lower bands thathave IF coverage capable of performing broadbandblock conversions. A torroidal balun design utilizes acenter-tapped transformer to extract the IF frequency,allowing it to have overlapping RF, LO and IF fre-quency ranges. However, this approach is only usefulup to approximately 3 GHz before the performance offerrite core baluns falls off and bifilar coupling struc-tures become too small for practical use.
Above 2 GHz, the distributed or microstrip balun is uti-lized to perform the 180° transform required in a bal-anced design, as shown in Figure 3. The problem withthis balun had been that the center tap did not exist toseparate the IF from the RF or LO. As a result, diplexingand balance are needed to reject the RF or LO at the IFport in double-balanced designs. The problem with these
double-balanced designs is that the upper frequencyof the IF is dependent upon the quality of the diplexer.Because of the diplexer's filtering it is nearly impossi-ble for the IF to be close in frequency to the RF or LO.
In the early 1980s, a solution to this problem was real-ized using what is commonly referred to as a doubledouble-balanced or triple-balanced mixer design. Inthis approach, an additional microstrip balun and twicethe number of diodes are incorporated to providethree mutually balanced ports on the mixer. With thisapproach, only balance is required to cancel oneport's signal at the other. Therefore, overlapping fre-quencies and microwave IF coverage are no longerproblems.
The triple-balanced mixer is now common up to 26GHz with IF coverage available to 12 and sometimes15 GHz. Irrespective of its near-commodity status, amicrowave triple-balanced mixer is not a simpledevice. This design typically requires three orthogonalmicrostrip baluns with two diode quads soldered to allthree, as shown in Figure 4. The limitation to extend-ing this structure above 26 GHz has been typicallyassociated with the parasitics of the complicateddesign and construction.
FIGURE 4Higher frequency vesions of this same design havebeen developed over the last several years. In 1994,a breakthrough development resulted in the ModelTB0440LW1 4 to 40 GHz triple-balanced mixer.Through reconstruction of the diode structure andtightly controlled manufacturing processes, this newmixer offers what was needed all along to accomplishKa-band block frequency conversion.
BLOCK CONVERTER ASSEMBLY
A long with the development of a high-performancemillimeter-wave mixer, other support products had tobe developed to facilitate this LNB converter, asshown in Figure 5. As with most receivers, sensitivityis a critical electrical specification. To meet thisdemand, the JS series low-noise amplifiers (LNA)operating at frequencies up to 60 GHz were devel-oped. Integrated into the front end of the LNB-2640-40block converter is a 26 to 40 GHz LNA providing 24 dB
RFLO
IF
IF
LO
INOUT 0
OUT 180MICROWAVE
BALUN
RF
(a)
(b)
A (a) DOUBLE- AND(b) TRIPLE-BALANCED MIXER
A TRIPLE-BALANCEDMIXER ASSEMBLY
512
MILLIMETER-WAVE BLOCK CONVERTERS
unit to unit. The IF band is unfiltered and boosted ingain by a four-stage LNA operating over the 0.5 to 20GHz band. This amplifier not only drives the +10 dBmoutput power, but provides a good broadband matchfor interconnection to existing systems even through along cable run.
SYSTEM-LEVEL PERFORMANCE
A performance summary of the LNB converter’s indi-vidual components and the cumulative receiver is list-ed in Table 1. Table 2 lists some of the mixing spuri-ous signals that can be expected from a -40 dBm inputsignal. In addition to the listed typical performance, avariety of standard options are offered, including anoninverting frequency conversion utilizing low sideLO mixing, WR42 and WR28 waveguide inputs, anexternal LNA for remote feed applications, a lowphase noise LO utilizing dual-loop vs. digitally lockedtechnology and an internal crystal reference with fre-quency stability to ±1 PPM.
The applications realized with these millimeter-waveblock frequency converters span a variety of cus-tomers and markets. Block conversion is a simplesolution to a system option that was often overlookeddue to technical concerns. As technology moves fur-ther into the millimeter-wave bands, block conversionis expected to become a more frequently sought-aftersolution to broadband system problems.
MILLIMETER WAVE TYPICAL PERFORMANCE
LNA FILTER MIXER IF AMP RCVR TOTAL
Intercept point/compression reference output – input output output
Gain (dB) 28 -1 -10 20 37
Noise figure (dB) 2.5 1 10 5 2.65
1 dB compression (dBm) 8 – 13 10 7.7
Third-order intercept point (dBm) 18 +3 20 17.7
Second-harmonic intercept point (dBm) 31 26 33 3
TABLE 2
TABLE 1Reprinted with permission from Microwave Journal, July 1996.
MIXING SPURIOUS SIGNALS (dBc)
LO HARMONICS (N)
RF H
AR
MO
NIC
S (
M)
1 2 3 4 5
1 REF 26 12 33 22
2 46 52 46 56 47
3 58 63 59 70 63
4 80 >85 80 >85 >85
5 >85 >85 >85 >85 >85
of gain with a 2.5 dB noise figure.
Along with the LNA, a 42 GHz LO is required to facil-
itate the block conversion. A phase-locked ceramicresonator oscillator at 2.8 GHz, digitally locked to anexternal 10 MHz reference, is utilized. This frequencyis then multiplied and filtered to 14 GHz by a singlestep-recovery diode multiplier, and finally multipliedagain to 42 GHz by means of a balanced X3 Schottkydiode multiplier. The multiplied ceramic resonatorapproach was chosen over a phase-locked dielectricresonator oscillator (DRO) at 14 GHz due to the costimpact of utilizing the DRO. Although some size issacrificed, overall manufacturability and performanceare not compromised.
The final 42 GHz LO was chosen based upon thespurious signal performance of high side mixing, aswell as the ease of filtering the image response andLO leakage. With high side mixing, much of the imagesuppression is inherent in the roll-off of the amplifier.However, a multisection waveguide bandpass filter isincluded to ensure consistency in performance from
X 3
LNA
26 – 40 GHz 2 – 16 GHz
10 MHz
LO LO AMPLIFIER
HIGHPASS FILTER
IF AMPMIXER ATTENUATOR
ATTENUATOR
FIGURE 5
THE LNB BLOCK DIAGRAM
CU
STO
MPR
OD
UC
TS
513
CU
STO
MPR
OD
UC
TS
CUSTOM PRODUCTS ORDERING INFORMATION
IFMODEL FREQUENCY AVAILABLE
NUMBER OPTION (*) OPTIONS
ARS309LC7 - Contact Factory
LNB-1826-30 - Contact Factory
LNB-2640-40 - Contact Factory
DA40502LC7 - Contact Factory
DA40208LC7 - Contact Factory
DA40818LC7 - Contact Factory
DSS0818 - -
SYS40118C20(*) A, B, C -
IR3A8596LR6(*) A, B, C -
IR3A5459LR6(*) A, B, C -
SYS6474N01R - -
SYSTX3638 - Contact Factory
SYS1840A24R - -
SYS1840N01R - -
LNB-7181-02 - Contact Factory
SYS3436N01R - -
SYS0204N01R - -
SYS0118N01R - -
SYS0218N01R - -
SYS0318N01R - -
SYS0518N01R - -
SYS9.0N01R - -
SYS1015N01R - -
SYS0216N01R - -
top related