a+ guide to managing and maintaining your pc fifth edition chapter 6 managing memory

A+ Guide to Managing and Maintaining Your PCFifth Edition

Chapter 6

Managing Memory

2 A+ Guide to Managing and Maintaining Your PC, Fifth Edition

Memory Types

ROM – Read-Only Memory Permanent – retains data even when power is off System ROM BIOS, device ROM BIOS

RAM – Read-write Memory Volatile – losses data when power is off CPU cache memory, main memory


EEPROM

Electrically Erasable Programmable ROM – data can be erased under software control

“Flash BIOS”


RAMStatic RAM

(SRAM)Dynamic RAM

(DRAM)

Speed Faster

Cost more expensive

Size more space

Simplicity no refresh Constant refresh

Usage L1/L2/L3 cache Main memory

Addressing No Yes

% of accesses 90-95% 5-10%


The Memory Controller Is normally integrated into the chipset

(northbridge) Controls accesses to CPU caches and main

memory CPU caches: predicts and prefetches instructions

and data Main memory:

• specifies the memory address on the address bus

• Interfaces with processor and other devices


DRAM Refresh

Operates every a few milliseconds A refresh circuit reads the contents of each

memory cell, whether it is being used or not The reading action itself refreshes the memory

contents


DRAM Memory Accesses

Asynchronous accesses Not synchronized to the system clock For lower-speed memory buses (< 66 MHz)

Synchronous accesses Synchronized to the system clock Much faster than asynchronous DRAM For higher-speed memory systems of newer PCs


Representative Dynamic RAM Technologies Asynchronous DRAM

EDO (Extended Data Out): Pentium /486 SDRAM (Synchronous DRAM)

Regular SDRAM DDR (Double-data Rate) SDRAM: doubles the

bandwidth by transferring data twice per cycle Rambus DRAM (RDRAM) – not the trend


Error-detection using Parity Parity

Older method of error-detection An additional parity bit to make an even/odd

number of ones or an odd number of ones


Error-correcting Code (ECC) Current method of error checking that can

detect and correct an error of a single bit 8 ECC bits for 8 bytes (64 bits)


DRAM Speed Ratings

Speed in nanoseconds – the minimum access time for a read/write to memory

SDRAM Speed in MHz – reciprocal of the nanoseconds

speed• E.g., 100 MHz (10ns)

Speed rating: PCXXX• PC100-compatible (8ns)


Memory Packaging

Dual Inline Packages (DIPs) Memory Modules A DIP

A MemoryModule


Memory Modules

SIMM (Single Inline Memory Module) 30-pin: 8 bits of data (+ 1 bit parity) 72-pin: 32 bits of data (+ 4 bits parity/ECC)

DIMM (Dual Inline Memory Module) 168-pin: 64 bits of data (+ 8 bits parity/ECC) 184-pin DDR: 64 bits of data (+ 8 bits ECC) SODIMM – laptop computers

RIMM: 184-pin


Examples of Memory Modules


72-pin SIMM

Intel 486, 586 and some early Pentium desktop 32 bits data width

36 bits with parity EDO and Fast page mode (FPM) technologies 4, 8, 16, and 32 MBytes 60ns – 70ns


168-pin DIMMs

FPM, EDO, and Synchronous DRAM (SDRAM)

64 bits data width 72 bits (with 8 bits ECC) 80 bits (with 16 bits ECC)

Buffered/unbuffered Serial Presence Detect: an EERPOM that

stores configuration information of the module


Identifying the DIMM Module


Memory Banks

PCs read a certain bit width of memory at a time, typically 32 or 64, and the memory making up this width is called a bank

72-pin SIMMs: banks of two for a system with 64-bit system bus data path

168-pin DIMMs: installed as a single module for a system with 64-bit system bus data path


Gold/Tin Connectors and Sockets 30-pin SIMMs: often with gold contacts 72-pin SIMMs: usually found with tin contacts 168-pin DIMMs: generally found only with

gold contacts


Memory Size Specifications

D*W-S D: # of memory units for each bit W: data width of the module in bits S: speed of the module in nanoseconds

E.g. 2x32-60 4x9-70 128MB 16x64, 16x72


Memory Module Quality Factors

DRAM Quality Number of Chips on the Module – beware of

modules that have too many chips on them Module Quality Warranty


Installing a SIMM Module


Installing a DIMM Module


Installing a RIMM Module


Using Motherboard Documentation to Select Memory


Using Motherboard Documentation to Select Memory (continued)


Troubleshooting Memory

What to do if the computer does not recognize new SIMMs, DIMMs, or RIMMs, or memory error messages appear

Recurring errors during normal operations can mean unreliable memory


DOS Memory Management


Memory Layout

Conventional Memory

Upper Memory Area (UMA)

1 MB

High Memory Area (HMA) 64 KB

384 KB

640 KB

Extended Memory


Conventional Memory

The first 640 KB of system memory (00000h to 9FFFFh)

Used by DOS and standard DOS programs (device drivers, user programs, etc……)

Goal: free up as much as possible space to user programs


Upper Memory Area (UMA)

The next 384 KB of the system memory (A0000h - FFFFFh)

Reserved for system BIOS, device BIOSes, and system devices


UMA LayoutAddress First 16K

(0000h-3FFFh)

Second 16 K

(4000h-7FFFh)

Third 16K

(8000h-BFFFh)

Fourth 16K

(C000h-FFFFh)

A0000-AFFFFh

Video Card RAM

B0000-BFFFFh

Video Card RAM

C0000-CFFFFh

Video Card BIOS IDE Hard Disk BIOS

D0000-DFFFFh

E0000-EFFFFh

F0000-FFFFFh

System BIOS ROM


Upper Memory Blocks (UMBs)

The parts of the upper memory that are not used by ROM or for video RAM

EMM386.exe: a UMB provider that enables DOS programs and device drivers to access UMBs


Load DOS programs in UMBs

Config.sys must includedevice = himem.sys

device = emm386.exe

dos = UMB


Load Device Drivers in UMBs

Load device drivers in config.sysdevicehigh = mydrive.sys e.g, DBLSPACE.SYS, PRINTER.SYS,

DISPLAY.SYS,RAMDRIVE.SYS Load DOS programs in autoexec.bat

loadhigh program e.g., DOSKEY, DOSSHELL, KEYB


Extended Memory

All of the memory above the first megabyte The first 64 KB (high memory area HMA) can

be accessed by DOS programs Beyond 64 KB can only be accessed by

Windows programs Himem.sys: manages extended memory


High memory Area (HMA)

The first 64 KB after 1 MB of the memory (100000h-10FFEFh)

HIMEM.SYS enables DOS programs (practically the DOS itself) to used this memory


Load DOS High

Open config.sys Type in

device = himem.sys

DOS = high


A Typical Config.sys

device = himem.sys

device = emm386.exe

dos = high,UMB

devicehigh = XXX.sys


Windows Virtual Memory Management


Virtual Memory

Each application has 2 GB of virtual memory space

2 GB Virtual MemoryApplication 1

Application 2

2 GB Virtual Memory

WindowsVM

Manager

RAMMemory

SwapFile


Virtual Memory Settings in Windows 9x Start->Settings->Control Panel->System-

>Performance tab->Virtual Memory Change the size of the swap file Check c:\windows\win386.swp


Virtual Memory Settings in Windows 2000/XP Figure 6-26 Open a MS-DOS window, type “dir /ah” to see

the swap file

a+ guide to managing and maintaining your pc fifth edition chapter 6 managing memory

Documents