4-port antenna r1 y1 frequency range 698–960 dual … · 80010666v01 page 1 of 4 4-port antenna...
TRANSCRIPT
80010666V01 Page 1 of 4
4-Port AntennaFrequency RangeDual PolarizationHPBWAdjust. Electr. DTset by hand or by optional RCU (Remote Control Unit)
1710–2690
Y1Y1
698–960
R1R1
XX
65°65°
2°–8°1.5°–10°
936.
4652
/e
ngm
n 04
.18.
08.0
7 S
ubje
ct to
alte
ratio
n.
4-Port Antenna 698–960/1710–2690 65°/65° 17/18.5dBi 1.5°–10°/2°–8°T
Type No. 80010666V01Lowband R1, connector 1–2R1, connector 1–2
698–960Frequency Range MHz 698 – 806 790 – 862 824 – 894 880 – 960
Gain at mid Tilt dBi 16.0 16.6 16.9 17.1
Gain over all Tilts dBi 16.0 ± 0.5 16.5 ± 0.4 16.8 ± 0.4 17.0 ± 0.2
Horizontal Pattern:Azimuth Beamwidth ° 71 ± 2.2 68 ± 1.0 68 ± 0.9 67 ± 1.5
Front-to-Back Ratio,Total Power, ± 30°
dB > 22 > 24 > 26 > 27
Cross Polar Discriminationat Boresight
dB > 23 > 22 > 22 > 21
Cross Polar Discriminationover Sector
dB > 8.0 > 8.5 > 9.5 > 8.5
Vertical Pattern:Elevation Beamwidth ° 8.4 ± 0.7 7.7 ± 0.4 7.5 ± 0.4 7.0 ± 0.3
Electrical Downtiltcontinuously adjustable
° 1.5 – 10.0
Tilt Accuracy ° < 0.3 < 0.3 < 0.3 < 0.3
First Upper Side Lobe Suppression
dB > 16 > 17 > 16 > 15
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 16 > 17 > 16 > 15
Cross Polar Isolation dB > 30
Port to Port Isolation dB > 30 (R1 // Y1)
Max. Effective Powerper Port
W 400 (at 50 °C ambient temperature)
Max. Effective PowerPort 1–2
W 800 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Page 2 of 4 80010666V01
936.
4652
/e
ngm
n 04
.18.
08.0
7 S
ubje
ct to
alte
ratio
n.
4-Port Antenna
Highband Y1, connector 3–4Y1, connector 3–4
1710–2690Frequency Range MHz 1710 – 1880 1850 – 1990 1920 – 2170 2300 – 2400 2490 – 2690
Gain at mid Tilt dBi 18.0 18.5 18.8 18.6 19.0
Gain over all Tilts dBi 18.0 ± 0.4 18.5 ± 0.4 18.7 ± 0.4 18.5 ± 0.7 18.8 ± 0.4
Horizontal Pattern:Azimuth Beamwidth ° 64 ± 3.4 62 ± 2.9 62 ± 2.2 60 ± 4.8 60 ± 2.0
Front-to-Back Ratio,Total Power, ± 30°
dB > 25 > 26 > 27 > 25 > 26
Cross Polar Discriminationat Boresight
dB > 15 > 18 > 20 > 16 > 21
Cross Polar Discriminationover Sector
dB > 8.0 > 11.0 > 11.0 > 10.0 > 9.5
Vertical Pattern:Elevation Beamwidth ° 5.0 ± 0.4 4.7 ± 0.2 4.4 ± 0.4 3.9 ± 0.2 3.5 ± 0.2
Electrical Downtiltcontinuously adjustable
° 2.0 – 8.0
Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.2 < 0.2
First Upper Side Lobe Suppression
dB > 19 > 18 > 20 > 20 > 18
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 16 > 16 > 16 > 16 > 17
Cross Polar Isolation dB > 28
Port to Port Isolation dB > 30 (R1 // Y1)
Max. Effective Powerper Port
W 200 (at 50 °C ambient temperature)
Max. Effective PowerPort 3–4
W 400 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
80010666V01 Page 3 of 4
936.
4652
/e
ngm
n 04
.18.
08.0
7 S
ubje
ct to
alte
ratio
n.4-Port Antenna
Adjustment mechanismwith integrated scale
All dimensionsin mm | inches
2622
| 10
3.2
2652
| 10
4.4
2692
| 10
6.0
2)1)
1) 9 | 0.42) 72 | 2.8
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.Wall mounting: No additional mounting kit needed.
Material: Refl ector screen: Aluminum.Fiberglass housing: It covers totally the internal antenna components. The special design reduces the sealing areas to a minimum and guarantees the best weather protection. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance and painting. The color of the radome is light grey.All nuts and bolts: Stainless steel or hot-dip galvanized steel.
Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
Electrical specifi cations, all systems
Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 30Passive Intermodulation dBc < –150 (2 x 43 dBm carrier)Polarization ° +45, –45Max. Effective Powerfor the Antenna W 900 (at 50 °C ambient
temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifi cations
Input 4 x 7-16 female long neckConnector Position bottomAdjustment Mechanism 2x, Position bottom
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 530 | 119Maximal: 845 | 190
Max. Wind Velocity km/hmph
200124
Height / Width / Depth mminches
2622 / 300 / 152103.2 / 11.8 / 6.0
Category of Mounting Hardware H (Heavy)
Weight kglb
29.0 / 31.2 (clamps incl.)63.9 / 68.8 (clamps incl.)
Packing Size mminches
2951 / 322 / 190116.2 / 12.7 / 7.5
Scope of Supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
Accessories (order separately if required)
Type No. Description Remarksmm | inches
Weight approx.kg | lb
Units per antenna
85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 285010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 285010008 1 downtilt kit Downtilt angle: 0° – 8° 4.3 | 9.5 1
Accessories (included in the scope of supply)738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Page 4 of 4 80010666V01
4-Port Antenna
173
| 6.8
*
46 |
1.8
49 |
1.9
108
| 4.3
101 | 4.0
221 | 8.7
244 | 9.6
152
| 6.0
*
300 | 11.8 *
Tilt 1710-2690Tilt 6
98-960
Bottom view* Dimensions refer to radomeAll dimensions in mm | inches
Layout of interface:
Correlation Table
Frequency range Array Connector
698– 960 MHz R1 1–2
1710–2690 MHz Y1 3–4
R1Y1
936.
4652
/e
ngm
n 04
.18.
08.0
7 S
ubje
ct to
alte
ratio
n.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
738546 Page 1 of 1
Mounting HardwareClamp Included in the Scope of Supply
936.
3920
/c
Sub
ject
to a
ltera
tion.
Suitable for mast diameter (mm)[inches]
42 – 115[1.65 – 4.53]
Antenna – mast distance (mm)[inches]
20 – 25[0.79 – 0.98]
Material of clamp and screws Hot-dip galvanized steel / stainless steel
Weight (kg)[lb]
1.1[2.43]
Please note: Kathrein does not recommend to use counter nuts.The additional nuts supplied are only meant as spares.
All dimensions in mm and [inches]
152 [5.98]
100 [3.94]40 [1.57]
72 [2.83]
35 [1.38]
64 [2.52]
125 [4.92]
40 [1
.57]
20–
25
[0.7
9–
0.98
]
42–115
[1.65–4.53]
M10 MA = 25 Nm
M8 MA = 20 Nm
20–25
[0.79–0.98]
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Page 1 of 2
936.
4037
/a
Sub
ject
to
alte
ratio
n.General Instructionsfor Adjustment Mechanism
Description of the adjustment mechanism (protective cap removed):
Manual adjustment procedure:
Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:
For a description of RCU installation please refer to the respective data sheet.
Remove the protective cap and the twist protection completely.
➀ Twist protection.➁ Downtilt spindle with integrated
scale.
➀ Thread for fi xing the pro tectivecap or the RCU (Remote ControlUnit).
➁ Gearwheel for RCU power drive.
To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gear-wheel must be used for alignment.
Set downtilt angle by rotating the gearwheel.
Screw on the twist protection and the protective cap again.
0° – max.°
0° – max.°
1
2
2
1
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Page 2 of 2
936.
4037
/a
Sub
ject
to
alte
ratio
n.
Installation of the feederline connector and RCU (optional):In order to protect the adjustment mechanism, the protective caps have to be attached during feederline installation!
Carefully place the connector and fi x the nut using a torque-wrench (according to the manufacturers guidelines).
After feederline installation, the optional remote control units (RCUs) can be mounted.
These tools are suitable for 7-16 connectors with a wrench size of 27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a wrench size of 41 mm | 1.6 inches.
Tighten nuts within a torque range of 25 – 33 Nm depending on connector manufacturers’ specifi cations, respectively the RCU nut with a torque range of 15 – 18 Nm.
Kathrein installation set: Type No. 85010077Set has to be ordered separately!Set consists of three spanners of divers width27, 32 and 41 mm | 1.1, 1.3 and 1.6 inches
32 | 1.3
41 | 1
.627 | 1.1
1/2˝ square actuationaccording toDIN 3120 Form C
All dimensions in mm | inches
Colour coding:Correlation of each RF input to:– the corresponding adjustment mechanism– the frequency range– the polarization
Ventilation hole
Spindle with tilting scale
7-16 female (long neck)
Adjustment mechanism(protective cap removed)
General Instructions for Feederline and RCU Installation for Antennas
Please note: In order not to damage the interfaces, please make sure that only the right tools are used. Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench width.
Description of bottom end cap (exemplary picture):
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com