8-port antenna frequency range dual polarization hpbw … · 80010826 page 1 of 4 8-port antenna...
TRANSCRIPT
80010826 Page 1 of 4
8-Port AntennaFrequency RangeDual PolarizationHPBWAdjust. Electr. DTset by hand or by optional RCU (Remote Control Unit)
1710–2180 1710–2180790–960 790–960
X XX X
60° 60°65° 65°
0°–6° 0°–6°0°–8° 0°–8°
R2R2 B1B1 B2B2R1R193
6.48
87/b
ng
mn
04.1
9.02
.00
Sub
ject
to
alte
ratio
n.
8-Port Antenna 790–960/790–960/1710–2180/1710–2180 65°/65°/60°/60° 17/17/18.5/18.5dBi0°–8°/0°–8°/0°–6°/0°–6°T
Type No. 80010826Lowbands R1R1 R2R2
790–960 790–960Frequency Range MHz 790 – 862 824 – 894 880 – 960 790 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 16.6 16.8 16.7 16.5 16.8 16.8Gain over all Tilts dBi 16.5 ± 0.3 16.6 ± 0.2 16.6 ± 0.3 16.5 ± 0.4 16.6 ± 0.2 16.6 ± 0.3Horizontal Pattern:Azimuth Beamwidth ° 65 ± 2.3 64 ± 2.0 62 ± 2.4 66 ± 2.8 64 ± 2.2 63 ± 2.5Front-to-Back Ratio,Total Power, ± 30°
dB > 26 > 27 > 28 > 25 > 26 > 27
Cross Polar Discriminationat Boresight
dB > 31 > 32 > 29 > 30 > 30 > 29
Cross Polar Discrimination over Sector
dB > 15.0 > 13.5 > 12.0 > 15.0 > 14.0 > 11.5
Azimuth Beam Port-to-Port Tracking
dB < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 < 1.5
Vertical Pattern:Elevation Beamwidth ° 8.1 ± 0.3 7.9 ± 0.3 7.5 ± 0.3 8.0 ± 0.3 7.8 ± 0.3 7.5 ± 0.3Electrical Downtiltcontinuously adjustable
° 0.0 – 8.0 0.0 – 8.0
Tilt Accuracy ° < 0.2 < 0.2 < 0.3 < 0.2 < 0.2 < 0.3First Upper Side Lobe Suppression
dB > 16 > 17 > 16 > 16 > 17 > 16
Cross Polar Isolation dB > 30 > 30Port to Port Isolation dB > 30 (R1 // R2 // B1 // B2) > 30 (R1 // R2 // B1 // B2)Max. Effective Powerper Port
W 400 (at 50 °C ambient temperature) 400 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Page 2 of 4 80010826
936.
4887
/b
ngm
n 04
.19.
02.0
0 S
ubje
ct t
o al
tera
tion.
8-Port Antenna
Highbands B1B1 B2B2
1710–2180 1710–2180Frequency Range MHz 1710 – 1880 1850 – 1990 1920 – 2180 1710 – 1880 1850 – 1990 1920 – 2180Gain at mid Tilt dBi 18.4 18.5 18.4 18.4 18.6 18.6Gain over all Tilts dBi 18.3 ± 0.3 18.4 ± 0.4 18.2 ± 0.5 18.3 ± 0.4 18.5 ± 0.5 18.4 ± 0.5Horizontal Pattern:Azimuth Beamwidth ° 60 ± 2.4 57 ± 2.5 59 ± 3.4 60 ± 2.9 57 ± 2.1 58 ± 3.2Front-to-Back Ratio,Total Power, ± 30°
dB > 26 > 25 > 24 > 25 > 26 > 26
Cross Polar Discriminationat Boresight
dB > 28 > 28 > 24 > 28 > 27 > 24
Cross Polar Discrimination over Sector
dB > 16.0 > 15.5 > 10.0 > 15.0 > 14.5 > 9.5
Azimuth Beam Port-to-Port Tracking
dB < 0.5 < 1.0 < 1.5 < 0.5 < 1.0 < 1.5
Vertical Pattern:Elevation Beamwidth ° 5.0 ± 0.3 4.7 ± 0.2 4.5 ± 0.4 5.0 ± 0.3 4.7 ± 0.2 4.5 ± 0.4Electrical Downtiltcontinuously adjustable
° 0.0 – 6.0 0.0 – 6.0
Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.3 < 0.2 < 0.2First Upper Side Lobe Suppression
dB > 14 > 14 > 14 > 14 > 15 > 15
Cross Polar Isolation dB > 30 > 30Port to Port Isolation dB > 30 (R1 // R2 // B1 // B2) > 30 (R1 // R2 // B1 // B2)Max. Effective Powerper Port
W 250 (at 50 °C ambient temperature) 250 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Any previous data sheet issues have now become invalid.
8-Port Antenna
80010826 Page 3 of 4
936.
4887
/b
ngm
n 04
.19.
02.0
0 S
ubje
ct t
o al
tera
tion.
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.Wall mounting with two half clamps 738546 (included in the scope of supply).
Material: Refl ector screen: Weather-proof aluminum.Fiberglass radome: The grey fi berglass radomes of these antennas are very stable and extraordinarily stiff. They are resistant to ultraviolet radiation and can also be painted to match their surroundings.All screws and nuts: Stainless steel
Grounding: The metal parts of the antenna including the mounting and the inner conductors are DC grounded.
Accessories (order separately if required)
Type No. Description Remarksmm | inches
Weight approx.kg | lb
Units per antenna
85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 285010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 285010008 1 downtilt kit Downtilt angle: 0° – 9° 4.3 | 9.5 1
Accessories (included in the scope of supply)738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2
2)
2399
| 94
.424
32 |
95.7
2472
| 97
.3
Adjustment mechanismwith integrated scale
All dimensions in mm | inches
1)1) 9 | 0.42) 72 | 2.8
Electrical specifi cations, all systems
Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 30Passive Intermodulation dBc < –150 (2 x 43 dBm carrier)Polarization ° –45, +45Max. Effective Powerfor the Antenna W 1200 (at 50 °C ambient
temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifi cations
Input 8 x 7-16 femaleConnector Position bottomAdjustment Mechanism 4x, Position bottom
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 1550 | 348Maximal: 1705 | 383
Max. Wind Velocity km/hmph
200124
Height / Width / Depth mminches
2399 / 576 / 13394.4 / 22.7 / 5.2
Category of Mounting Hardware H (Heavy)
Weight kglb
39.0 / 41.2 (clamps incl.)86.0 / 90.8 (clamps incl.)
Packing Size mminches
2576 / 600 / 170101.4 / 23.6 / 6.7
Scope of Supply Panel and 2 units of clampsfor 42–115 mm |
1.7–4.5 inches diameter
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Any previous data sheet issues have now become invalid.
Page 4 of 4 80010826
936.
4887
/b
ngm
n 04
.19.
02.0
0 S
ubje
ct t
o al
tera
tion.
8-Port Antenna
Layout of interface:
Correlation Table
Frequency range Array Connector
790– 960 MHz R1 1–2 790– 960 MHz R2 3–41710–2180 MHz B1 5–61710–2180 MHz B2 7–8
R1B1
R2B2
Left Right
1) 2)
270 | 10.6 3)
476 | 18.7
576 | 22.7 *
Bottom view* Dimensions refer to radomeAll dimensions in mm | inches
99 |
3.9
110
| 4.3
133
| 5.2
*
34 |
1.3
4)
Tilt 790-960
17
10-2180 Tilt
Tilt 790-960 1710-2180
Tilt
56 |
2.2
1) 33.5 | 1.32) 35.5 | 1.43) 50 | 2.04) 45 | 1.8
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
738546 Page 1 of 1
Mounting HardwareClamp Included in the Scope of Supply
936.
3920
/c
Sub
ject
to a
ltera
tion.
Suitable for mast diameter (mm)[inches]
42 – 115[1.65 – 4.53]
Antenna – mast distance (mm)[inches]
20 – 25[0.79 – 0.98]
Material of clamp and screws Hot-dip galvanized steel / stainless steel
Weight (kg)[lb]
1.1[2.43]
Please note: Kathrein does not recommend to use counter nuts.The additional nuts supplied are only meant as spares.
All dimensions in mm and [inches]
152 [5.98]
100 [3.94]40 [1.57]
72 [2.83]
35 [1.38]
64 [2.52]
125 [4.92]
40 [1
.57]
20–
25
[0.7
9–
0.98
]
42–115
[1.65–4.53]
M10 MA = 25 Nm
M8 MA = 20 Nm
20–25
[0.79–0.98]
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Page 1 of 2
936.
4037
/a
Sub
ject
to
alte
ratio
n.General Instructionsfor Adjustment Mechanism
Description of the adjustment mechanism (protective cap removed):
Manual adjustment procedure:
Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:
For a description of RCU installation please refer to the respective data sheet.
Remove the protective cap and the twist protection completely.
➀ Twist protection.➁ Downtilt spindle with integrated
scale.
➀ Thread for fi xing the pro tectivecap or the RCU (Remote ControlUnit).
➁ Gearwheel for RCU power drive.
To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gear-wheel must be used for alignment.
Set downtilt angle by rotating the gearwheel.
Screw on the twist protection and the protective cap again.
0° – max.°
0° – max.°
1
2
2
1
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
Page 2 of 2
936.
4037
/a
Sub
ject
to
alte
ratio
n.
Installation of the feederline connector and RCU (optional):In order to protect the adjustment mechanism, the protective caps have to be attached during feederline installation!
Carefully place the connector and fi x the nut using a torque-wrench (according to the manufacturers guidelines).
After feederline installation, the optional remote control units (RCUs) can be mounted.
These tools are suitable for 7-16 connectors with a wrench size of 27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a wrench size of 41 mm | 1.6 inches.
Tighten nuts within a torque range of 25 – 33 Nm depending on connector manufacturers’ specifi cations, respectively the RCU nut with a torque range of 15 – 18 Nm.
Kathrein installation set: Type No. 85010077Set has to be ordered separately!Set consists of three spanners of divers width27, 32 and 41 mm | 1.1, 1.3 and 1.6 inches
32 | 1.3
41 | 1
.627 | 1.1
1/2˝ square actuationaccording toDIN 3120 Form C
All dimensions in mm | inches
Colour coding:Correlation of each RF input to:– the corresponding adjustment mechanism– the frequency range– the polarization
Ventilation hole
Spindle with tilting scale
7-16 female (long neck)
Adjustment mechanism(protective cap removed)
General Instructions for Feederline and RCU Installation for Antennas
Please note: In order not to damage the interfaces, please make sure that only the right tools are used. Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench width.
Description of bottom end cap (exemplary picture):
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com