2021 your #1 source catalog for the complete line of

Your #1 Source

For the complete

Line of Makita

Power tools, parts

And accessories

2021

CATALOG

TOOLS, PARTS

& ACCESSORIES

www.louiswilliams.com

Phone (828) 692-8216 Fax (828) 692-6344

since 1928

XFD07 18 Volt Cordless 1/2” Driver-Drill BRUSHLESS

Variable 2 speed (0-550 & 0-2100 RPM). delivers 1090in.lbs of torque.

Built in LED light., weighs 5.8lbs with battery

XFD07T 329.00 Kit w/Charger & 2 (5Ah)Batteries XFD07Z 149.00 Bare Tool Only

Cordless

XPH12 18 Volt Cordless 1/2” Hammer Driver-Drill BRUSHLESS

Variable 2 speed (0-500 & 0-2000 RPM). delivers 530in.lbs of torque. Built

in LED light. Compact, weighs 4lbs with battery

XPH12T 297.00 Kit w/Charger & 2 (5Ah)Battery XPH12Z 129.00 Bare Tool Only

XPH07Z 18 Volt Cordless 1/2” Hammer Driver-Drill BRUSHLESS

Variable 2 speed (0-550 & 0-2100 RPM). 4 pole motor delivers 1090in.lbs

of torque. Built in LED light. Compact, weighs 5.1lbs with battery.

XPH07Z 149.00 Bare Tool Only

XDT13 18 Volt Cordless 1/4” Impact Driver BRUSHLESS

Variable speed (0-2500 RPM). Delivers 1500in.lbs of torque. Built in LED

light. Weighs 3.4lbs with battery. Quick change 1/4” hex chuck.

XDT13T 299.00 Kit w/Charger & 2 (5Ah)Batteries XDT13Z 119.00 Bare Tool Only

XDT131 159.00 Kit w/Charger & 1 (3Ah) Battery


3 speed variable speed (0-1100, 0-2100, 0-3600 RPM). Delivers 1550in.lbs

of torque. Built in LED light. Weighs 3.3lbs with battery. Quick change

1/4” hex chuck. Battery gage and automatic speed change mode.

XDT14T 319.00 Kit w/Charger & 2(5Ah)Batteries XDT14Z 149.00 Bare Tool Only

XST01Z 18 Volt 1/4” Impact Driver Oil Impulse BRUSHLESS

30% lower nose. 3 speed variable speed (0-1200, 0-2200, 0-3200 RPM).

355in.lbs of torque. Built in LED light. Weighs 3.2lbs with battery. Quick

change 1/4” hex chuck. Battery gauge and automatic speed change mode.

XST01Z 199.00 Bare Tool Only , Battery and charger sold separately

2

XFD131 18 Volt Cordless 1/2” Driver-Drill Kit BRUSHLESS

Variable 2 speed (0-500 & 0-1900 RPM). delivers 440in.lbs of torque. Built

in LED light. Compact, weighs 3.8lbs with battery

XFD131 159.00 Kit w/Charger & 1 (3Ah)Batteries


4 speed variable speed (0-1100, 0-2100, 0-3200. 0-1300 RPM). Delivers

1600in.lbs of torque. Built in LED light. Weighs 3.3lbs with battery. Quick

change 1/4” hex chuck. Battery gage and automatic speed change mode.

XDT16T 349.00 Kit w/Charger & 2(5Ah)Batteries XDT16Z 184.00 Bare Tool Only

Cordless

XWT15Z 18 Volt Cordless 1/2” Impact Wrench BRUSHLESS

240ft lbs with 4 variable speeds. 1/2” sq drive. Built in LED light.

Compact, weighs 4lbs with battery. 5-5/8” long

XWT15Z 189.00 Bare Tool Only , battery and charger sold separately

XWT08T 18 Volt 1/2” High Torque Impact Wrench BRUSHLESS

740ft lbs of torque with 3 variable speeds . 1/2” sq drive. Built in LED

light. Compact, weighs 7.9lbs with battery. 9” long

XWT08T 479.00 Kit w/Charger & 2 (5Ah) Batteries XWT08Z 259.00 Bare Tool

XAD02 18 Volt 3/8” Cordless Angle Drill

Variable speed (0-1800 RPM). 4 pole motor delivers 121in.lbs of torque.

Built in LED light. Compact 3-1/2” angle head x 12-3/8” long, weighs 4lbs

with battery. Keyless chuck Kit w/Charger & 2 (3Ah) Batteries

XAD02 Kit w/Charger & 2 (3Ah) Batteries 399.00 XAD02Z 159.00 Bare Tool Only

XSF03Z 18 Volt Drywall Screwdriver BRUSHLESS Bare Tool Only

Variable speed (0-4000 RPM). 1860 screw per charge with 4 Ah battery.

Motor only starts when pushed against the screw . 1/4” hex adjustable

nose piece. Built in LED light. 3.8lbs with battery. 9-7/8” long

XSF03Z 159.00 Battery and charger sold separately

194500-1 30” Extension Handle for Auto-feed Screwdriver

105.00 3

XRF02Z 18 Volt Cordless Auto-feed Screwdriver Bare Tool Only

4000 RPM for decking & subfloor applications. 4 pole motor . 8-1/4” long.

Shoots 1-3/4” - 2-15/16” screws. Compact, weighs 5.2lbs with battery.

XRF02Z 219.00 Battery and charger sold separately

XLT01Z 18 Volt Cordless 1/4” Angle Impact Driver Bare Tool Only

530in lbs with 0-2000 RPM. 4 pole motor . 1/4” hex chuck. Paddle switch.

Built in LED light. Weighs 3.9lbs with battery. 15-1/4” long

XLT01Z 179.00 Battery and charger sold separately

XAD03Z 36 Volt Cordless 1/2” Right Angle Drill BRUSHLESS

0-350 & 1-1400 RPM. Electric brake and torque limiter w/built in clutch.

Drills up to 6-1/4” holes with hole saw and 4-5/8” holes with self feed bit.

Drills up to 160 2-9/16” holes per charge in 2xSPF. 21-1/4” long and

weighs 14lbs with batteries. Uses 2-18 volt batteries

XAD03PT 479.00w/2-5Ah batteries and charger XAD03Z 369.00 Bare Tool Only

XLT02Z 18 Volt Cordless 3/8” Angle Impact Driver Bare Tool Only

44 ft lbs with 0-2000 /0-3000RPM. 4 pole motor . 3/8” square drive.

Paddle switch. Built in LED light. Weighs 3.3lbs with battery. 15-1/4” long

XLT02Z 239.00 Battery and charger sold separately

XAG04Z 18 Volt Cordless 4-1/2” Grinder BRUSHLESS Bare Tool Only

8500 RPM, auto speed change adjusts speed to torque. LED battery

gauge . Soft start. Weighs 5.8lbs with battery. 14-1/4” long

XAG04Z 139 00 Battery and charger sold separately

XOC01Z 18 Volt Cordless Cut-Out Tool Bare Tool Only

30000 RPM. Accepts 1/8” and 1/4” bits. Weighs 3.7lbs with battery,

6-7/8” long and 2-1/4” diameter

XOC01Z 139.00 Battery and charger sold separately

XRH04Z 18 Volt Cordless 7/8” Rotary Hammer Bare Tool Only

3-modes: rotate, hammer w/ rotate and hammer. 0-1100 RPM & 0-4000

BPM. Torque limiting clutch 16-3/8” long, weighs 7lbs with battery.

Accepts SDS Plus bits

XRH04Z 165.00 Battery and charger sold separately

XDG01Z 18 Volt Cordless Die Grinder Bare Tool Only

25000 RPM. 1/4” collet. Aluminum housing. Side switch with lock-on.

Weighs 4.4lbs with battery, 15-3/4” long

XDG01Z 174.00 Battery and charger sold separately

XAG11Z 18 Volt Cordless 4-1/2” Grinder BRUSHLESS Bare Tool Only

8500 RPM, electric brake. auto speed adjust to torque. Paddle switch. LED

battery gauge . Soft start. Weighs 5.8lbs with battery. 14-1/4” long

XAG11Z 189 00 Battery and charger sold separately

XAG12Z1 36 Volt Cordless 7” Grinder BRUSHLESS Bare Tool Only

7800 RPM, electric brake. auto speed adjust to torque. Paddle switch. Soft

start. Uses 2–18 volt batteries. Weighs 11.4lbs with batteries.19-5/8” long

XAG12Z1 239.00 Batteries and charger sold separately

XRH07ZKU 36 Volt Cordless 1-9/16” Rotary Hammer BRUSHLESS Bare Tool Only

4-1/8” core bit capacity. 0-1450 2900BPM, 8.4 ft/lbs of impact. Torque

limiting clutch. Hammer w/rotation or chipping only. 18-5/8” long, 16.8lb

with 2 batteries. Uses SDS MAX bits. Uses 2—18 volt batteries.

XRH07ZKU 599.00 Batteries and charger sold separately

XRH07PTU 799.00 Kit includes 2 5Ah batteries and charger

Cordless

XBP02Z 18 Volt Cordless Band Saw Bare Tool Only

Variable 275-530 ft./min. Accepts 44-7/8” x 1/2” blades. 4-3/4” cutting

capacity. Built in LED light. Weighs 14.3lbs with battery. 20-5/8” long

XBP02Z 329.00 Battery and charger sold separately

4

XBP03Z 18 Volt Cordless Compact Band Saw Bare Tool Only

630 ft./min. Accepts 32-7/8” x 1/2” blades. 2-1/2” cutting capacity. Built

in LED light. Weighs 9lbs with battery. 18-3/4 long

XBP03Z 252.00 Battery and charger sold separately

Cordless

5

XSS02Z 18 Volt Cordless 6-1/2” Circular Saw Bare Tool Only

3700 RPM. 4 pole motor . 50° max bevel. 2-1/4” max cut at 90 deg and

1-9/16” max cut at 45 deg. Weighs 7.3lbs with battery.

XSS02Z 119.00 Battery and charger sold separately

XSH06Z 36 Volt Cordless 7-1/4” Circular Saw BRUSHLESS

6000 RPM. w/ electric brake. LED battery indicator. 56° max bevel. 2-5/8”

max cut at 90° and 1-7/8” max cut at 45°. Weighs 10.5lbs with battery.

Uses 2-18 volt batteries

XSH06Z 199.00 Battery and charger sold separately

XSH06PT 350.00 Kit includes 2 5Ah batteries and charger

XSH03Z 18 Volt Cordless 6-1/2” Circular Saw BRUSHLESS

5000 RPM. Automatic speed change. 50° max bevel. 2-1/4” max cut at

90 deg and 1-7/16” max cut at 45 deg. Weighs 7.3lbs with battery.

XSS03Z 199.00 Bare Tool Only , Battery and charger sold separately

XSR01Z 36 Volt Cordless 7-1/4” Circular Saw BRUSHLESS

5100 RPM. w/ electric brake. LED battery indicator. 53° max bevel. Up to

558 cross-cuts per charge. 2-9/16” max cut at 90° and 1-3/4” max cut at

45°. Weighs 12.4lbs with battery. 17-1/2” long. Uses 2-18 volt batteries

XSR01Z 199.00 Bare Tool Only, Battery and charger sold separately

XSR01PT 350.00 Kit includes 2 5Ah batteries and charger

XSS03Z 18 Volt Cordless 5-3/8” Trim Circular Saw Bare Tool Only

3600 RPM. 4 pole motor . 16 tooth carbide blade. 2” max cut at 90 deg

and 1-3/8” max cut at 45 deg. Weighs 6lbs with battery.14-3/8” long

XSS03Z 179.00 Battery and charger sold separately

XPS01Z 36 Volt Cordless 6-1/2” Plunge Saw BRUSHLESS

2500-6300 RPM. w/ electric brake. LED battery indicator. 48° max bevel.

2-3/16” max cut at 90° and 1-9/16” max cut at 45°. Weighs 11.2lbs with

batteries. 13-5/8” long. Uses 2-18 volt batteries

XPS01Z 349.00 Bare Tool Only, Batteries and charger sold separately

XPS01PTJ 499.00 Kit includes 2 5Ah batteries and charger

Guide Rail (Fits Makita plunge Saws)

194368-5 55” 99.00

194367-7 118” 258.00

P-45777 Guide Rail Connector Kit 36.00

XSL06Z 36 Volt 10” Slide Compound Miter Saw BRUSHLESS

4400 RP electronically controlled. Max cut:: 4x12 at 90° , vertical

cut 5-1/4” and crown mold 6-5/8 nested. Miters 0-60° left and right;

bevels 48° left and right. Up to 334 cuts per charge in 2x4 and

192 cuts in 2x12. Weighs 74lbs with battery.

XSL06Z 649.00 Battery and charger sold separately

XSL06PT 779.00 Kit includes 2 5Ah batteries and charger

XWL01Z 36 Volt Cordless 14” Cut Off Saw BRUSHLESS

3800 rpm. Max cut: 5” round and 4” x 7-5/8 rectangular. Soft start and

electric brake. Tool-less flange removal. Weighs 35.9lbs

XWL01Z 339.00 Battery and charger sold separately

XWL01PT 599.00 Kit includes 2 5Ah batteries and charger

6

Cordless

XVJ02Z 18 Volt Cordless Jig Saw BRUSHLESS Bare Tool Only

Variable 800-3500 SPM soft start. 3 orbital settings. 1” stroke. Dual LED

lights. Tool-less blade change. Weighs 5.8lbs with battery. 10-1/2” long

XVJ02Z 269.00 Battery and charger sold separately

XMT03Z 18 Volt Cordless Multi-Tool Bare Tool Only

Variable speed (6000-20000 OPM). Soft start. Tool-less blade change.

Weighs 4.91bs with battery. 12” long w/ 2-3/8” barrel

XMT035 349.00 Kit w/Charger & 2 (3Ah) Batteries XMT03Z 119.00 Bare Tool Only

XRJ01Z 18 Volt Cordless Compact Recip Saw Bare Tool Only

0-3000 spm w/1/2” stroke Dual switch, paddle or trigger operation. Tool-

less blade change. LED light. Weighs 3.9lbs with battery. 15-5/8” long

XRJ01Z 99.00 Battery and charger sold separately

XRJ04Z 18 Volt Cordless Recip Saw Bare Tool Only

0-2900 spm w/1-1/8” stroke. Variable speed trigger. Tool-less blade

change. Weighs 7.9lbs with battery. 17-3/4” long


XRJ06Z 36 Volt Cordless Recip Saw BRUSHLESS

0-2300 / 0-3000 spm w/1-1/4” stroke. Variable speed trigger. Tool-less

blade change. Weighs 10.2lbs with battery. 17-3/4” long


XRJ06PT 349.00 Kit includes 2 5Ah batteries and charger

XSC02Z 18 Volt Cordless 5-7/8” Metal Cutting Saw BRUSHLESS

3900 RPM, auto speed change. Built in LED light. Cuts Uni-strut, all

thread, channel, conduit, sheet metal, square tubing and more. 2-1/4”

max cutting depth . 13-1/8” long and weighs 6.4lbs with battery.

XSC02Z 199.00 Battery and charger sold separately

XRJ05Z 18 Volt Cordless Recip Saw BRUSHLESS

0-2300 / 0-3000 spm w/1-1/4” stroke. Variable speed trigger. Tool-less

blade change. Weighs 8.2lbs with battery. 17-1/4” long


XRJ05T 399.00 Kit includes 2 5Ah batteries and charger

XVJ03Z 18 Volt Cordless Jig Saw Bare Tool Only

Variable 0-2600 SPM soft start. 3 orbital settings. 1” stroke. LED light.

Tool-less blade change. Weighs 6.4lbs with battery. 10-1/8” long

XVJ03Z 159.00 Battery and charger sold separately

Cordless

7

XNJ01Z 18 Volt Cordless 16 Gauge Nibbler Bare Tool Only

1900 SPM. Die rotates 360°. Cutting radius: inner edge 1-3/4”, outer edge

2”. Weighs 4.8lbs w/battery, 12-3/8” long

XNJ01Z 369.00 Battery and charger sold separately

XOB01Z 18 Volt Cordless 5” Random Orbit Sander Bare Tool Only

3 Speed: 7000, 9500 and 11000 OPM. Runs up to 40 min on low speed.

Uses 8 hole hook-and-loop paper. Weighs 3.6lbs with battery, 6-7/8” long

X0B01Z 119.00 Battery and charger sold separately

XPK01Z 18 Volt Cordless 3-1/4” Planer Bare Tool Only

14000 RPM, 2 blade cutter head with double edge carbide blades. Electric

brake. Weighs 7.4lbs with battery and 13-1/8” long

XPK01Z 169.00 Battery and charger sold separately

XJP03Z 18 Volt Cordless Plate Joiner Bare Tool Only

6500 RPM, 4” blade cutting depth 3/4”.6 depth settings. 6 depth settings.

Fits biscuit sizes #0, #10 and #20. 13-3/4” long

XJP03Z 239.00 Battery and charger sold separately

XTR01Z 18 Volt Cordless Router BRUSHLESS Bare Tool Only

Variable speed 10,000-30,000 RPM. 1/4” & 3/8” collets included. Soft

start. Weighs 4.6bs with battery and 5-1/4” long

XTR01Z 129.00 Battery and charger sold separately

XNB01Z 18 Volt Cordless 2” Brad Nailer 18 Ga Bare Tool Only

Drives 5/8”-2” brad nails. Sequential or contact operation. Built in LED .

Tool less depth dial. Weighs 7.7 lb w/battery and 11-5/8” long

XNB01Z 259.00 Battery and charger sold separately

XTS01Z 18 Volt Cordless 3/8” Crown Stapler Bare Tool Only

Drives 1/4”-7/8’ staples, compatible with T50 Arrow. Contact actuation.

Depth control dial. Weighs 5.3lbs w/battery and 9-7/8” long

XTS01Z 199.00 Battery and charger sold separately

XTP02Z 18 Volt Cordless Pin Nailer 23 Ga Bare Tool Only

Drives pin nails 11/16”,1”,1-3/16” and 1-3/8”. Magazine capacity up to

130 nails. Tool less depth dial. Weighs 4.6 lb w/battery and 9-3/4” long

XTP02Z 195.00 Battery and charger sold separately

XNB02Z 18 Volt Cordless 2-1/2” Finish Nailer 16 Ga Tool Only

Drives 1”-2-1/2” finish nails. Magazine holds 110 nails. Built in LED . Tool

less depth dial. Weighs 8.4 lb w/battery and 11-5/8” long

XNB02Z 319.00 Battery and charger sold separately

8

XCV08Z 36 Volt Dry HEPA Vacuum BRUSHLESS Bare Tool Only

74CFM suction and 36” of water lift with batteries. 3 stage HEPA filtration.

2.1 gal container. AWS wireless on/off communication with other tools.

Up to 75min run time on low and 40 min on high using 2-18 volt batteries

not included. Weighs 18.4lbs with battery

XCV08Z 539.00 Battery and charger sold separately

DCL501Z 18 Volt Cyclonic Canister Vacuum Bare Tool Only

46CFM suction power and 26.5” water lift. .Up to 49min run time. Cyclonic

filter separation. Weighs 9.4bs with battery and 13-7/8” long

DCL500Z 310.00 Battery and charger sold separately

XCV09Z 36 Volt Backpack HEPA Vacuum BRUSHLESS Bare Tool Only

70CFM suction and 44” of water lift. 2 stage HEPA filtration. Up to

116min run time on 2-18 volt batteries. Weighs 9.9lbs with batteries.

XCV09Z 499.00 Batteries and charger sold separately

Cordless

XCV11Z 18 Volt 2 Gal HEPA Wet/Dry Vacuum BRUSHLESS Tool Only

57CFM suction and 27” water lift. 2gal . Up to 60min run time on a

charge.3 micron HEPA filter. Weighs 10.1bs with battery and 13-7/8” long

XCV11Z 179.00 Battery and charger sold separately

DCF201Z 18 Volt Cordless Job Site Fan Bare Tool Only

2 speed 17000 RPM & 1200 RPM. Up to 5.5 hours run time w/ 5 Ah

battery. Adjustable platform. 3 Stage automatic timer and AC adapter

DCF201Z 89.00 Battery and charger sold separately

DCF300Z 18 Volt Cordless 13”Job Site Fan Bare Tool Only

3 speed and oscillation. Up to 5.7 hours run time w/ 5 Ah battery. Tilts up

and down. 3 Stage automatic timer and AC adapter


XLC02ZB 18 Volt Cordless Vacuum Bare Tool Only

1.3 pint capacity. Up to 15min of run time with a 2ah battery and 33min

run time with a 5ah battery. Weighs 2.7lbs with 2ah battery and 19” long

XLC02ZB 89.00 Battery and charger sold separately

XLC02R1B 179.00 Includes 1 –2Ah battery and charger

DCF102Z 18 Volt Cordless 7-1/8” Fan Bare Tool Only

3 speed and oscillation. Up to 9.5 hours run time on med w/ 5 Ah battery.

Tilts up and down. 3 Stage timer. Hook for hanging


Cyclonic Attachment (Fits XLC01BZ Vacuum)

Captures 90% of dust particles before entering main canister.

199553-5 39.00

9

18 Volt Heated Jacket

5 core heat zones (left chest, right chest, back both pockets). Fleece

interior. 3 heat setting LED heat controller. Up to 28 hours of heat on 1

charge using a 5.0Ah battery. Battery and charger sold separately

Small DCJ205ZS 195.00

Medium DCJ205ZM 195.00

Large DCJ205ZL 195.00

DCM501Z 18 Volt Cordless/Corded Coffee Maker Bare Tool Only

Brews up to (3) 5 oz cups on a single 5 Ah battery. No paper filter needed.

Weighs 4.8lbs with battery and 8-9/16” tall

DCM500Z 99.00 Battery and charger sold separately

Cordless

X large DCJ205ZXL 195.00

2X large DCJ205Z2XL 195.00

3X large DCJ205Z3XL 219.00

XGC01ZC 18 Volt 29oz Caulk & Adhesive Gun Bare Tool Only

Delivers 1100lbs of dispensing force w/ variable speed trigger. 5 speed

flow rate. Fits 28-29oz cartridges Built in LED . Weighs 5.9lbs w/battery

and 18-7/8” long

XGC01ZC 239.00 Battery and charger sold separately

XGC01Z 18 Volt 10oz Caulk & Adhesive Gun Bare Tool Only

Delivers 1100lbs of dispensing force w/ variable speed trigger. 5 speed

flow rate. Fits 10oz cartridges Built in LED . Weighs 5.1lbs w/battery and

15-7/8” long

XGC01Z 239.00 Battery and charger sold separately

DMP180ZX 18 Volt Cordless Inflator

120 psi capacity. 25-1/2” hose. Auto-stop at preset pressure. Weighs

3.1lbs with battery. 9-7/8” long

DMP180ZX 99.00 Battery and charger sold separately

DMP180SYX 179.00 Kit includes 1 2Ah battery and charger

XRM06B 18 Volt Cordless Bluetooth Jobsite Radio Bare Tool Only

Up to 35 hrs of play on one 18 volt battery. Equipped with Bluetooth to

connect your mobile device10 preset buttons. Auxiliary port for MP3/iPod.

AC adapter included. Weighs 10.8lbs

XRM06B 159.00 Battery and charger sold separately

XRM08B 18 Volt Bluetooth Jobsite Speaker Bare Tool Only

Up to 31 hrs operation with Bluetooth connected to your mobile device.

1 auxiliary port for MP3 and 1 USB port for charging mobile devices. AC

adapter included. Weighs 7.2lbs

XRM08B 119.00 Battery and charger sold separately

ADP05 Cordless Power Source

Accepts 18 volt LXT battery and charges up to 2 USB compatible devices

ADP05 25.97

10

DML805 18 Volt Cordless/Corded LED Flood Light

750 lumens. Max run time using 5 Ah battery: 8.5 hrs on hi and 17 hrs on

low. Includes optional AC adapter

DML805 109.00 Battery and charger sold separately

DML801 18 Volt Cordless 12 LED Flashlight

240 lumens on 12 LED mode, 120 lumens on 6 LED mode. Max run time

using 5 Ah battery: 17 hrs on hi and 40 hrs on low


DML802 18 Volt Cordless LED Flashlight

200 lumens . 21 hrs max run time using 5 Ah battery


GM00001381 Flood Light Stand

Holds up to DML805 lights: Telescopes to 58”

GM00001381 74.00 Flood light sold separately

DML806 18 Volt Cordless LED Flashlight / Lantern

3 LED modes: 360deg lantern (620 lumens), 180deg lantern(310 lumens)

or flashlight (90 lumens). Up to 11 hrs run time using 5 Ah battery


DML811 18 Volt Cordless/Corded LED Flood Light

3000 lumens. Max run time using 6 Ah battery: 3 hrs on hi and 13 hrs on

low. Includes optional AC adapter


Cordless

DML800 18 Volt Cordless LED Headlamp

100 lumens,33 hrs max run time using 5 Ah battery. Adjusts 0– 90 deg.

Battery holder with built in clip for attaching to belt


DML810 36 Volt Cordless/Corded Upright LED Flood Light

5500 lumens on high. Max run time using 2 -5 Ah battery: 3.3 hrs on hi

and 15 hrs on low. Includes optional AC adapter

DML810 439.00 Batteries and charger sold separately

XT611PT 18 Volt Cordless 6 Pc Combo Kit BRUSHLESS

Includes XPH07Z hammer drill, XRJ05Z recip saw, XDT14Z impact

driver,XSH03Z circular saw, XAG04Z grinder, DML802 flashlight, 2 (5Ah)

18 volt batteries, 2 port charger and bag

819.00

11

CX200RB 18 Volt Cordless 2Pc Sub-Compact Combo Kit BRUSHLESS

Includes XFD11ZB drill, XDT15ZB impact driver, 2 (2Ah) 18 volt batteries,

charger and bag

239.00

XT269T 18 Volt Cordless 2 Pc Combo Kit BRUSHLESS

Includes XPH12Z hammer drill, XDT13Z impact driver, 2 (5Ah) 18 volt

batteries, charger and bag

299.00


Includes XPH07Z hammer drill, XDT13Z impact driver, 2 (5Ah) 18 volt

batteries, charger and case

399.00


Includes XPH07Z hammer drill, XRJ05Z recip saw, XSH03Z circular saw,

DML802 flashlight, 2 (5Ah) 18 volt batteries, charger and bag

569.00


Includes XPH07Z hammer drill, XDT14Z impact driver, XRJ05Z recip saw,

DML802 flashlight, 2 (5Ah) 18 volt batteries, charger and bag

549.00

Cordless Combo Kits

XT505 18 Volt Cordless 5 Pc Combo Kit


driver,XSS02Z circular saw, DML185 flashlight, 2 (3Ah) 18 volt batteries,

charger and bag

499.00

XT706 18 Volt Cordless 7 Pc Combo Kit


driver,XSS02Z circular saw, XAG04Z grinder, DML185 flashlight,

DUB182Z blower, 2 (3Ah) 18 volt batteries, charger and bag

669.00

12

XML03PT1 18 Volt X2 (36V) Cordless 18” Lawn Mower BRUSHLESS

2500-3300 RPM. Cuts up to 7300 square feet using 5.0Ah batteries. 16

gallon grass catcher bag. Adjustable cutting heights. Steel deck. Weighs

60.5lbs with batteries and 68-1/8” tall. Uses 2—18 volt batteries

XML03Z 469.00 Tool Only, Batteries and charger sold separately

XML03PT1 599.00 Includes 2 - 5Ah batteries, Dual Port Charger

XHU07T 18 Volt Cordless 24” Hedge Trimmer BRUSHLESS

3 speed2000-3600-4400 SPM. 24” blade. Low noise level. 5 position

rotating handle. Weighs 8.65lbs with battery and 44-1/4”” long.

Uses 1—18 volt battery

XHU07Z 249.00 Tool Only, Batteries and charger sold separately

XHU07T 389.00 Includes 1— 4Ah Battery & Charger

Cordless Outdoor Power

XRU15PT1 18 Volt X2 (36V) String Trimmer BRUSHLESS

3 speed: 3500, 5300 and 6500 RPM. Automatic Torque Drive Technology

mode automatically shifts RPM for extended runt time or added power.

Weighs 10.4lbs with battery and 69-1/4” long. Bump feed trimmer head.

Uses 2—18 volt batteries

XRU15Z 269.00 Tool Only, Batteries and charger sold separately

XRU15PT1 389.00 Includes 2 - 5Ah batteries, Dual Port Charger

XRU12SM1 18 Volt String Trimmer BRUSHLESS

3 speed: 4000, 5000, 6000 RPM. Over heat warning system indicator with

automatic shut-off. 11-3/4” cutting capacity. Reverse rotation to clear

trimmer head. Weighs 8.6lbs with battery and 72-1/2” long. Bump feed

trimmer head. Uses 1—18 volt battery

XRU12Z 149.00 Tool Only, Battery and charger sold separately

XRU12SM1 199.00 Includes 1 - 4Ah Battery, & Charger

XHU04PT 18 Volt X2 (36V) Cordless 25-1/2” Hedge Trimmer

0-1800 SPM. Up to 60min run time on a charge using 2– 5Ah batteries.

25-1/2“ blade. Weighs 12.2lbs with battery and 48-3/4” long. Only 87 dB

low noise level. 5 Position rear handle. Uses 2—18 volt batteries

XHU04Z 249.00 Tool Only, Batteries and charger sold separately

XHU04PT 379.00 Includes 2 - 5Ah batteries, Dual Port Charger

XMU04Z 18 Volt Cordless Grass Shear Bare Tool Only

7800 RPM. Up to 200 min run time on a single charge. 6-5/16” cutting

capacity with 3 stage height adjustment. Tool-less blade change. Weighs

4.1lbs with battery and 13-7/8” long. Uses 1—18 volt battery

XMU04Z 99.00 Tool Only, Battery and charger sold separately

XUC01PTX1 18 Volt X2(36V)Cordless Power-Assisted Wheelbarrow

2 speed max 2.5mph on a 12 deg incline. Max load 275lbs. Up to 45 min

of run time. 7” dsic brakes . LED lights on easch side of frame. Weighs

87.2lbs and 43-3/4” long. Uses 2—18 volt batteries

XUC01PTX1 1149.00 Includes 2 - 5Ah batteries, Dual Port Charger

BRUSHLESS

988-394-610 2.6 Gallon Pressurized Water Tank

Provides pressurized water when standard hose is not available. Controls

dust when cutting masonry products with wet use diamond blade. Up to

74 psi. Connect directly to water supply on Makita power cut saws

988-394-610 119.00

13

Cordless 9” Power Cutter

XEC01PT1 18 Volt X2 (36V) Cordless 9” Power Cutter

6,600 RPM.7/8” arbor Cuts up to 3-1/2” deep. Weighs 13.7lbs with battery

and 21-3/4” long. 114 dB low noise level. Uses 2—18 volt batteries.

Includes diamond blade and abrasive cut off wheel

XEC01Z 679.00 Tool Only, Batteries and charger sold separately

XEC01PT1 895.00 Includes 4 - 5Ah batteries, Dual Port Charger

Eliminates the hassles of gas with lower weight, reduced maintenance, and zero emissions

allowing use in indoor environments

The BL™ Brushless Motor powered by two 18V LXT® Lithium-Ion batteries eliminate the

hassle of engine pull starts allowing immediate starts-up

Integrated water delivery system with water flow adjustment knob continuously feeds

water for OSHA Table 1 Compliance in concrete cutting applications

Active Feedback-sensing Technology (AFT®) turns the motor off if rotation of the wheel

is suddenly forced to stop

Electric brake stops the wheel in 4 seconds or less allowing for faster re-positioning

Built-in L.E.D. light with an independent on/off switch illuminates the cutting area for

increased visibility

Makes single pass cuts up to a 3-1/2" depth in various masonry and metal materials

Integrated overload indicator alerts of excessive battery power draw during heavy

loads

Overload protection is designed to protect the motor from burnout in abnormally high

torque situations

Soft start suppresses start-up reaction for smoother start-ups and longer gear life

Protective battery compartment helps prevent dust and slurry contamination

Extreme Protection Technology (XPT™) is engineered for improved dust and water re-

sistance for operation in harsh conditions

Rubberized front handle can be held in multiple positions for increased comfort at

various cutting orientations

Belt-drive design provides smoother operation with lower vibration

Lock-off power switch requires two actions to start power

Large spindle lock button for easier wheel changes while wearing gloves

XBU05Z 18 Volt Cordless Blower Bare Tool Only

3 speed variable. Up to 17 min run time on high speed WITH 6 Ah battery.

Produces up to219 MPH. Weighs 4.1lbs with battery and 20-3/8” long

XBU05Z 119.00 Battery and charger sold separately

XCU03PT1 18 Volt X2 (36V) 14” Cordless Chainsaw BRUSHLESS

Variable speed trigger 0-3940 FPM. Electric Brake. Tool-less chain

adjustment. Auto chain lubricator. Low noise (100dB) . Weighs 11.5lbs

with batteries and 30-1/2” long. Uses 2—18 volt batteries

XCU03Z 279.00 Tool Only, Battery and charger sold separately

XCU03PT1 399.00 Includes 2 - 5Ah batteries, Dual Port Charger

XBU02PT1 18 Volt X2 (36V) Cordless Blower BRUSHLESS

Variable speed. 473 CFM, 120 MPH. Low noise (60.2dB) . Weighs 9.9lbs


XBU02Z 219.00 Tool Only, Battery and charger sold separately

XBU02PT1 329.00 Includes 2 - 5Ah batteries, Dual Port Charger


XCU06T 18 Volt 10” Cordless Top Handle Chainsaw BRUSHLESS

0-4720 FPM. Electric Brake. Auto chain lubricator. Torque boost mode for

cutting dense material. Low noise. Weighs 7.2lbs with battery and 19-3/8”

long. Uses 1—18 volt battery


XCU06T 319.00 Includes 2 - 5Ah batteries and Charger

14

XCU04PT 18 Volt X2 (36V) 16” Cordless Chainsaw BRUSHLESS

Variable speed trigger 0-3940 FPM. Electric Brake. Tool-less chain

adjustment. Auto chain lubricator. Low noise (100dB) . Weighs 11.9lbs



XCU04PT 409.00 Includes 2 - 5Ah batteries, Dual Port Charger

XBU03Z 18 Volt Cordless Blower BRUSHLESS

Variable speed. 459 CFM, 116 MPH. Low noise (60dB) . Weighs 6.5lbs with

battery and 32-1/2” long.

XBU03Z 139.00 Tool Only, Battery and charger sold separately

XCU08PT 18 Volt X2 (36V) 14” Top Handle Chainsaw BRUSHLESS

Variable speed trigger 0-3940 FPM. Electric Brake. Torque boost mode for

cutting dense material. Auto lubricator. Power equal to 30cc. Weighs

10.2lbs with batteries. 3/8” pitch, .043”. chain Uses 2—18 volt batteries



XCU09PT 18 Volt X2 (36V) 16” Top Handle Chainsaw BRUSHLESS

Variable speed trigger 0-3940 FPM. Electric Brake. Torque boost mode for

cutting dense material. Auto lubricator. Power equal to 30cc. Weighs

10.3lbs with batteries. 3/8” pitch, .043”. chain Uses 2—18 volt batteries



EN410MP Hedge Trimmer Attachment

20” double sided blade.4.45lbs 199.00

LE400MP Extension Attachment

42” extended shaft. 2.5lbs 79.00

15

XUX01Z 18 Volt X2 (36V) Coupled Shaft Power Head BRUSHLESS

3 speed: 0-5700, 0-8200 and 0-9700 RPM. Tool-less lever lock for

attachments. Electronic torque control. Uses 2—18 volt batteries

XUX01Z 269.00 Power Head Only, Battery and charger sold separately

XUX01M5PT 449.00 Power Head w/String Trimmer Attachment , 2 batteries & charger

EM405MP String Trimmer Attachment

17” Cut. M10x1.25 arbor bump head. 3.3lbs 109.00

EY401MP Pole Saw Attachment

10” bar with bar oil tank. 3.35lbs 199.00

EM403MP Brush Cutter Attachment

17” Bump head included. Brush Blade is optional. 3.7lbs 119.00

EN401MP Articulating Hedge Trimmer Attachment

20” double sided blade, 13 adjustable angles. 3.35lbs 299.00

ER400MP Curved Shaft String Trimmer Attachment

17” Cut. M8x1.25 arbor bump head. 2.1lbs 89.00

KR401MP Cultivator Attachment

9” , 6 tine blade. 6.65lbs 242.00


SW400MP Paddle Sweep Attachment

23-1/4” wide. 12 rubber paddles . 15.8lbs 365.00

BR400MP Bristle Brush Attachment

23-5/8” wide. Durable nylon bristles. 13.9lbs 330.00

EE400MP Edger Attachment (For Gas Power Head Only)

8” blade. Adjustable wheels. 5.4lbs 199.00

Batteries & Chargers

18 Volt LXT Battery Charger

Charges up to 5 Ah LXT battery

DC18RC 110.00 120 volt AC Charger

DC18SE 120.00 Automotive 12 volt DC charger

DC18RD 18 Volt LXT Battery Charger

Charges (2) LXT batteries in only 45 minutes. USB port built in

DC18RD 129.00 120 volt AC Charger

DC18SF 18 Volt LXT Battery Charger

4 port. Charges (2) LXT batteries at a time.

DC18SF 169.00 120 volt AC Charger

DC1804 7.2-18 Volt Pod & Stick Style Battery Charger

Charges older Makita Ni-Cd and Ni-Mh batteries

DC1804 72.00 120 volt AC Charger

18 Volt LXT Batteries

LXT Lithium-Ion batteries fit New Style Makita Cordless Tools

BL1820B 79.00 2.0 Ah (compact)

BL1830B 99.00 3.0Ah BL1830B2 (2pack) 159.00

BL1840B 109.00 4.0Ah BL1840B2 (2pack) 189.00

BL1850B 129.00 5.0Ah BL1850B2 (2pack) 219.00

BL1860B 159.00 6.0Ah BL1860B2 (2pack) 299.00

Pod Style Batteries

Ni-MH batteries for Older Makita Cordless Tools

193157-5 89.00 12 Volt 2.6 Ah 1234

193158-3 96.50 14.4 Volt 2.6 Ah 1434

193159-1 109.00 18 Volt 2.6 Ah 1834

BL1850BDC1 18 Volt LXT Battery Charger Battery Starter Pack

Includes DC18RC charger and 1— BL1850B 5 Ah LXT battery

169.00

16

BL1850B2DC2 18 Volt LXT Battery Charger Battery Starter Pack

Includes DC18RD dual port charger and 2— BL1850B 5 Ah LXT batteries

289.00

6302H 1/2” Drill

6.5 amps. Variable speed 0-550 RPM. 1/2” keyed chuck. Metal gear

housing. Weighs 4.8lbs

149.00

6408K 3/8” Drill

4.9 amps. Variable speed 0-2500 RPM. 3/8” keyless chuck. Case included.

Weighs 3.1lbs

89.00

Drills

DS4011 1/2” Spade Handle Drill

8.5 amps variable speed 0-600 RPM . D handle rotates 360°. Weighs

6.2lbs

184.00

DA4000LR 1/2” Angle Drill

7.5 amps. 2 speed variable speed 0-400 and 0-900 RPM. 360°. Angle

attachment for drilling in any position. Weighs 8.1lbs

339.00

DA3010F 3/8” Angle Drill

4 amps. Variable speed 0-2400 RPM. 360°. Paddle switch. Built in LED

light. Weighs 3.5lbs, 10-5/8” long and 2-5/8” head width.

239.00

DA4031 1/2” Angle Drill

10 amps. 2 speed 300 and 1200 RPM. Handle rotates 90° left or right.

Adjustable top handle. Built in clutch. Weighs 12.3lbs

409.00

17

DP4000 1/2” Drill

7 amps. Variable speed 0-950 RPM. 1/2” keyed chuck. Metal gear housing.

Weighs 4.8lbs

179.00

DP4002 1/2” Drill

7 amps. Variable speed 0-700 RPM. 1/2” keyed chuck. Metal gear housing.

Weighs 4.8lbs

189.00

DS4000 1/2” Spade Handle Drill

9 amps 500 RPM . D handle rotates 360°. Forward/reverse rocker switch.

12” pipe handle. Weighs 8.8lbs

299.00

FS6200 6000 RPM Drywall Screwdriver

6 amps. Variable speed 0-6000 RPM. Includes 3” magnetic bit holder.

Built in LED light. Weighs 3lbs

114.00



Built in LED light. Weighs 3.5lbs

119.00

FS2500 2500 RPM Screwdriver w/ Depth Control

6 amps. Variable speed 0-2500 RPM. Accepts 1/4” hex bits. Adjustable

depth locator assembly. Built in LED light. Weighs 3.4lbs

179.00

FS2701 2500 RPM Screwdriver w/ Torque Control

6 amps. Variable speed 0-2500 RPM. Accepts 1/4” hex bits. 6 stage

torque adjustment. Built in LED light. Weighs 4lbs

199.00

6952 1/4” Impact Driver

2.3 amps. 0-3000 RPM. Accepts 1/4” hex bits. 88.5ft.lbs or torque.

Weighs 3.1lbs

229.00

TW0200 1/2” Impact Driver

3.3 amps. Variable speed 0-2200 RPM. 1/2” square drive. 150ft.lbs of

torque. Weighs 4.9lbs

214.00

TW0350 1/2” Impact Driver

3.5 amps. Variable speed 0-2000 RPM. 1/2” square drive. 260ft.lbs of

torque. Weighs 6.6lbs

229.00

6906 3/4” Impact Driver

9 amps. 1700 RPM. 3/4” square drive. 433ft.lbs of torque. Side handle

adjusts 360 deg. Weighs 12.3lbs

599.00

Screwdrivers & Impact Drivers



Built in LED light. Weighs 3lbs

114.00

18

HP1641K 5/8” Hammer Drill

6 amps. Variable speed 0-2800 RPM. Rotation or rotation with hammer.

1/2” keyless chuck. Drills up to 5/8” hole. Includes case. Weighs 4.3lbs

111.00

HR4041C 1-9/16” Spline Rotary Hammer

12 amps. 230-460 RPM. Accepts spline bits. Electronic controller. Hammer

only or hammer with rotation . Drills up to 1-9/16” with concrete bit and

4-5/8” with core bit. Weighs 14.8lbs

419.00

Hammer Drills & Demo Hammers

HP2010N 3/4” Hammer Drill

6 amps. 2 speed variable speed 0-900 and 0-2300 RPM. 1/2” chuck.

Drills up to 3/4” hole. Includes case. Weighs 6.4lbs

239.00

HR2475 1” SDS Rotary Hammer

7 amps. 0-1100 RPM. SDS plus chuck. Drills up to 1 hole. Rotation only,

hammer w/rotation or hammer only. Includes case. Weighs 6.6lbs

180.00

HR4002 1-9/16” SDS MAX Rotary Hammer

10 amps. 680 RPM. Accepts SDS-MAX bits. Torque limiting clutch.

Hammer only or hammer with rotation . Drills up to 1-9/16” with concrete

bit and 4-1/8” with core bit. Weighs 14.6lb s

389.00

HR4013C 1-9/16” SDS MAX AVT Rotary Hammer

11 amps. Soft start 250-500 RPM. Accepts SDS-MAX bits. Torque limiting

clutch. Hammer only or hammer with rotation . Constant speed control.

LED service light. Auto brush cut-off. Drills up to 1-9/16” with concrete bit

and 4-1/8” with core bit. Weighs 15.1lbs

599.00

HK1810 Power Scraper

4.5 amps. 0-3200 BPM. Accepts Makita small bits. Includes 2 scaling

chisels and a bull point chisel. Auto brush cut-off. Weighs 7.1lbs

429.00

HM1317CB 42LB Demolition Hammer

14 amps. 730-1450 BPM. Anti vibration technology. 25.7ft.lbs of energy.

Accepts 1-1/8” hex bits. LED indictor 8hrs before brushes need replacing.

Weighs 41.9lbs

1199.00

HM1810X3 70LB Demolition Hammer Kit w/Cart

15 amps. 1100 BPM. Anti vibration technology. 46.5ft.lbs of energy.

Accepts Makita 1-1/8” hex bits. .Weighs 71.3lbs

1615.00

19

Saws

5005BA 5-1/2” Circular Saw

8 amps. 8000 RPM. Electric brake. Blade left design. Cuts 1-3/4” at 90°

and 1-3/16” at 45°. Weighs 6.2lbs

279.00

5007F 7-1/4” Circular Saw

15 amps. 5800 RPM. Cuts 2-3/8” at 90° and 1-3/4” at 45°. Built-in LED

lights. Weighs 11.1lbs

129.00 5007F

149.00 5007FA same as 5007F with an electric brake

5007MG 7-1/4” Circular Saw MAGNESIUM

15 amps. 5800 RPM. Cuts 2-1/2” at 90° and 1-3/4” at 45°. Bevel cut up to

56”. Built-in LED lights. Weighs 10.6lbs

159.00 5007MG

189.00 5007MGA same as 5007MG with an electric brake

5477NB 7-1/2” Hypoid Circular Saw

15 amps. 4500 RPM. More power than worm drives. Blade left design.

Cuts 2-3/8” at 90° , 1-3/4” at 45°and 1-9/16” at 50°. Weighs 14.3lbs

149.00

5377MG 7-1/2” Hypoid Circular Saw MAGNESIUM

15 amps. 4500 RPM. More power than worm drives. Electric brake. Cuts

2-3/8” at 90° , 1-3/4” at 45°and 1-9/16” at 50°. Weighs 13.2lbs

199.00

5008MGA 8-1/4” Circular Saw MAGNESIUM

15 amps. 5200 RPM. Cuts 3” at 90°, 2-1/4” at 45° and 2” at 50”. Electric

brake. Built-in LED lights. Weighs 11.4lbs

239.00

HS0600 10-1/4” Circular Saw

15 amps. 4300 RPM. Bevel to 50 deg. Magnesium base. Cuts 3-13/16” at

90° and 2-11/16” at 45°. Weighs 15.2lbs. Includes 24 tooth carbide blade

299.00

5402NA 16-5/16” Circular Saw

15 amps. 2200 RPM. Electric brake. Cuts 6-3/16” at 90° and 4-3/16” at

45°. Weighs 32.1lbs. Includes 32 tooth carbide blade

799.00

20

Saws

4100NH 4-3/8” Masonry Saw

12amps. 14500 RPM. Blade left design. Cuts 1-3/8”at 90°. Weighs 6.5lbs.

4”diamond turbo blade included

149.00

4101RH 5” Wet Cutting Masonry Saw

7.9 amps. 13800 RPM. Blade left design. Cuts 1-5/8”at 90°and 1” at 45”.

Weighs 6.5lbs. 5”diamond continuous rim blade, water regulator and 15’

tubing and GFCI plug

369.00

SP6000J 6-1/2” Plunge Circular Saw (Panel Saw)

12 amps. 2000-5200 RPM. Electronic speed control. Cuts 2-3/16” at 90°

and 1-9/16” at 45°. Close to wall cutting (11/16”). Soft start. Magnesium

components. Weighs 9.7bs

379.00 SP6000J

429.00 SP6000J1 same as SP6000J plus 55” guide rail

4131 7-1/4” Metal Cutting Saw

13 amps. 3500 RPM. Cuts 2-1/2” deep. CERMET tipped blade leaves metal

bur free and cool to touch. Spark-free cuts. Weighs 11.3lbs

349.00

LC1230 12” Metal Cutting Saw

15 amps. 1300 RPM. Cuts 4-1/2” at 90” and 3-1/2” at 45”. Carbide tipped

blade lasts 50X longer & cuts 4X faster than abrasive blades. Leaves metal

bur free and cool to touch. Weighs 42.5lbs

539.00

LW1401 14” Metal Cutting Saw

15 amps. 3800 RPM. Cuts 5’ round or 4x7-5/8 rectangle at 90” . Abrasive

blade with 1” arbor. Tool-less vice adjustment. Weighs 37lbs

214.00

21

5057KB 7-1/4” Fibered Cement Cutting Saw w/ Dust Collector

13 amps. 5800 RPM. Cuts 5 stacked 5/16” siding boards in a pass. Guard

retracts for plunge cuts. CT blade. Weighs 11.8lbs

399.00

Guide Rail (Fits Makita plunge Saws)

194368-5 55” 99.00

194367-7 118” 258.00

P-45777 Guide Rail Connector Kit 36.00

TM3010CX1 Multi–Tool Kit

3 amps. Variable electronic speed 6000-20000 OPM. 3.2” oscillation

angle. Tool-less blade change. Includes case. Weighs 3.5lbs

159.00

JR3051T Recipro Saw

12amps. Variable speed 0-3000 SPM. 1-3/16’ stoke. Tool-less blade

change. Tool hook secures tool when not in use. Weighs 7.3lbs

109.00

Saws

JR3070CT Recipro Saw AVT 2X less vibration

15amps. Variable speed 0-2800 SPM. 1-1/4’ stoke. 4 position orbital

action. Built-in clutch. Tool-less blade change. Includes case. Weighs 10lbs

207.00

2107FZK Portable Band Saw

6.5amps. Variable speed 200-350ft/min. Cuts 4-3/4”x4-3/4”. Accepts

standard 44-7/8”x1/2” blades. Built-in high output fluorescent light.

Includes case. Weighs 13.1lbs

369.00

4329K Top Handle Jig Saw

3.9amps. Variable speed dial 500-3100 SPM. 11/16’ stoke. 3 positon

orbital settings. Uses Tang shank blades. Includes case. Weighs 4.2lbs

79.00

4350FCT Top Handle Jig Saw

6.3amps. Electronic speed 800-2800 SPM. 1’ stoke. 3 positon orbital

settings. Tool-less blade change. Uses Tang shank blades. 40% less tool

vibration with the lowest noise level in its class. Weighs 5.7lbs

189.00

4351FCT Barrel Grip Jig Saw

6.3amps. Electronic speed 800-2800 SPM. 1’ stoke. 3 positon orbital

settings. Tool-less blade change. Uses Tang shank blades. 40% less tool

vibration with the lowest noise level in its class. Weighs 5.5lbs

199.00

22

JV0600K Top Handle Jig Saw

6.5amps. 500-3100 SPM. 7/8’ stoke. 3 positon orbital settings. Tool-less

blade change. Uses Tang shank blades. Includes tool case. Weighs 5.2lbs

124.00

WST05 Jobsite Miter Saw Stand (fits all Makita Miter Saws)

239.00

23

Saws

LS1040 10” Compound Miter Saw

15 amps. 4600 RPM. Max cut 2-3/4”x5-1/8” at 90° and 1-3/8”x3-5/8” at

45° L/R. Miter cuts 0°-45° left and 0°-52° right. Weighs 27.3lbs

279.00

LS1221 12” Compound Miter Saw

15 amps. 4000 RPM. Max cut 3-7/8”x6” at 90° and 2-3/4”x5-7/8” at 45°

L/R. Miter cuts 0°-48° left and 0°-48° right. 4-1/2” tall pivoting fence for

cutting up to 5-1/2” crown molding. Weighs 37.3lbs

319.00

LS1018 10” Dual Slide Compound Miter Saw

13 amps. 4300 RPM. Soft start, & electric brake. D handle design. Cuts

3-5/8”x12” at 90° and 3-5/8”x8-1/2” at 45°. Linear ball bearings. Large

aluminum base. Weighs 43.7lbs

499.00

LS0815F 8-1/2” Slide Compound Miter Saw

10.5 amps. 5000 RPM. Soft start. Cuts 2-9/16”x12” at 90° and 2-9/6”x8-

1/2” at 45°. Miters0°-50° left and 0°-60° right. Weighs 31.1lbs

449.00

LS1219L 12” Dual Slide Compound Miter Saw

15 amps. 3200 RPM. Soft start, electronic speed control. Built –in laser.

8” nested crown molding cutting capacity. Cuts 3-5/8””x15” at 90° and

3-5/8”x10-1/2” at 45°. Operation flush against wall. Weighs 57.9lbs

739.00 LS1219L

WST06 Folding Miter Saw Stand (fits all Makita Miter Saws)

199.00

LS1019L 10” Dual Slide Compound Miter Saw

15 amps. 3200 RPM. Soft start, electronic speed control. Built –in laser.

6-5/8” nested crown molding cutting capacity. Cuts 2-13/16”x12” at 90°

and 2-13/16”x8-1/2” at 45°. Operation flush against wall. Weighs 57lbs

599.00 LS1019L

759.00 LS1019LX Includes WST06 Miter Saw Stand

Planers, Vacs & Heat Guns

24

2012NB 12” Portable Planer

15 amps. 8500 RPM. 4 post. Cuts 1/8’ depth and 6-3/32” thick. 2 knives

w/ auto head clamp to eliminate snipe. 12”x30-3/8 table. Weighs 61.9lbs

749.00

KP0800K 3-1/4” Planer

6.5 amps. 17000 RPM. Cuts 3/32’ depth in a single pass . Double edge

carbide, 2 knives. Includes case. Weighs 5.7lbs

169.00

1912B 4-3/8” Planer

7.5 amps. 16000 RPM. Cuts 1/16’ depth in a single pass. 2 knives.

Weighs 9.3lbs

299.00

1002BA 4-3/8” Curved Base Planer

9.6 amps. 15000 RPM. For planning logs at a 12-5/8” curved radius. Cuts

3/16’ deep. 2 knives. Weighs 11.4lbs

449.00

1806B 6-3/4” Planer

10.9 amps. 15000 RPM. Cuts 1/16’ depth in a single pass. 2 knives.

Weighs 19.8lbs

729.00

KP312 12-1/4” Planer

15 amps. 12000 RPM. Cuts 1/8’ depth in a single pass. 2 knives. Weighs

40.6lbs

2229.00

PJ7000 Plate Joiner

5.65 amps. 11000 RPM. 6 depth settings, max depth 3/4”. 4” carbide

blade. Includes case and dust bag. Weighs 5.5lbs

199.00

VC4210L 11 Gallon Wet / Dry HEPA Vacuum

12 amp variable speed motor148CFM suction power and 92” of water lift .

Auto filter cleaning system.3 stage HEPA filtration. included. 9 gal wet

capacity. Meets EPA rule for HEPA vacs with optional main HEPA filter

installed. Weighs 27lbs

619.00

HG6031VK Heat Gun

13 amps. Variable 122-1022F. 2 speed , 7 and 14 CFM. Weighs 1.5lbs

119.00

Sanders & Polishers

BO5030K 5” Rando Orbit Sander

3 amps. 1200 OPM. 1/8” orbital action. Uses hook-and –loop 8 hook

paper. Through the pad dust collection. Includes case. Weighs 2.9lbs

74.00

BO4556K Finishing Sander

2 amps. 14000 OPM. Uses 4-1/2”x5-1/2” paper. Clamping lever for quick

install. Through the pad dust collection. Includes case. Weighs 2.5lbs

59.00

9031 1-1/8”x21” Belt Sander

5 amps. Variable speed 656-3280ft/min. Dust collector connection. Multi

position handle. Weighs 4.6lbs

279.00

9903 3”x21” Belt Sander

8.8 amps. Variable speed 690-1440ft/min. Sands flush to wall. Auto track

belt system. Dust bag included. Weighs 9.5lbs

249.00


8.8 amps. Variable speed 690-1440ft/min. Sands flush to wall. Auto track

belt system. Dust bag included. Weighs 9.9lbs

259.00


11 amps. 1640 ft/min. Sands flush to wall. 360deg adjustable dust bag

included. Weighs 12.6lbs

279.00

GV5010 5” Disc Sander

4.2 amps. 4500RPM. Compact design . Weighs 2.6lbs

99.95

9237CX3 7” Polisher Kit

10 amps. Electronic variable speed 0-3000RPM. Soft start. Kit includes 2

wool pads and bag. Weighs 7lbs

249.00

25

BO5031K 5” Rando Orbit Sander, Variable Speed

3 amps. 4000-1200 OPM. 1/8” orbital action. Uses hook-and –loop 8

hook paper. Through the pad dust collection. Includes case. Weighs 3lbs

95.00

9564CV 4-1/2” Variable Speed Angle Grinder

12 amps. Electronic variable speed 2800-10500 RPM. Soft start. Tool-less

wheel guard. SJS clutch system. Weighs 5.2Lbs

166.00

9557PBX1 4-1/2” Ange Grinder w/case and Diamond Blade

7.5 amps. 11000 RPM. AC/DC paddle switch. Push button spindle lock.

Aluminum Case, diamond blade and 5 grinding discs. Weighs 4.5lbs

89.00

GA7001L 7” Ange Grinder

15 amps. 6000 RPM. AC/DC switch. All metal housing. Weighs 12.6lbs

245.00

GD0600 1/4” Die Grinder

3.5 amps. 25000 RPM. AC/DC paddle switch. 1/4” collet. Weighs 3.7lbs

159.00

9565CV 5” Variable Speed Angle Grinder

12 amps. Electronic variable speed 2800-10500 RPM. Soft start. Tool-less

wheel guard. SJS clutch system. Weighs 5.3Lbs

179.00

9557NB 4-1/2” Angle Grinder

7.5 amps. 10000 RPM. AC/DC slide switch. Push button spindle lock.

Weighs 4.5lbs

76.00

GA7021 7” Angle Grinder

15 amps. 6000 RPM. Spiral beveled gears for smooth rotation. Tool-less

wheel guard. Weighs 12.2bs

159.00

GA4530 4-1/2” Angle Grinder

6 amps. 11000 RPM. Slide switch either lock-on, Small diameter barrel

grip only 2-1/4”. Weighs 4lbs

69.00

Grinders

26

4114 14” Angle Cutter (Electric)

3800 RPM 15 amp motor. Cuts 5” deep. Removable base for close edge

work. Mechanical clutch system prevents motor damage. Weighs 23.8lbs

679.00

3709 1/4” Fixed Base Laminate Trimmer

4 amps. 30000 RPM. 1/4” collet. Transparent base. Weighs 3.3lbs

129.00

RP2301FC 3-1/4 HP Plunge Router

15 amps. Electronic variable speed 9000-22000 RPM. Soft start and

electric brake. 1/4” &1/2” collet. . Weighs 13.4lbs

329.00

RF1101KIT2 2-1/4 HP Router Kit With Plunge Base

11 amps. Electronic variable speed 8000-24000 RPM. Soft start. 1/4” &

1/2” collet. Includes fixed base, plunge base and case. Weighs 7.2lbs

289.00

Routers, Nibblers & Shears

JN1601 16 Gauge Nibbler

5 amps. 2200 SPM. 1/4” stroke. Die head rotates 360”. Cuts 16ga mild

steel and 18ga stainless. Weighs 3.6lbs

329.00

JN3201 10 Gauge Nibbler

6.2 amps. 1300 SPM. Built in thickness gauge. Cuts 10ga mild steel and

13ga stainless. Weighs 7.4lbs

589.00

JS1602 16 Gauge Shear



329.00

JS3201 10 Gauge Shear



559.00

JS8000 Fiber Cement Shear

6.2 amps. 0-2500 SPM. 5/16” cutting capacity. Tool hook. Weighs 4.8lbs

279.00

27

RT0701C 1-1/4 HP Compact Router

6.5 amps electronic variable speed 10000-30000 RPM. Smooth rack and

pinion depth adjustment. 1/4” collet. Weighs 3.9lbs

99.00

MAC700 2 HP Air Compressor

12.4 amps.1730 RPM. 3.8CFM@40PSI and 3.3CFM@90PSI . Oil lubricated

cast iron pump. 130PSI cut out pressure. 2.6gal tank. Weighs 52.0lbs

215.00

MAC5200 3 HP Air Compressor

13.8 amps. 1730 RPM. 6.9CFM@40PSI and 6.5CFM@90PSI . Oil lubricated

cast iron pump. 140PSI cut out pressure. 5.2gal tank. Weighs 88 lbs

359.00

AF506 2” Brad Nailer

70-120PSI. Shoots 5/8”-2” 18ga brads. 2 SCFM@90PSI. Reload indicator.

Tool-less depth adjustment. 100 brad magazine capacity. Weighs 2.9lbs

109.00

AN924 3-1/2” Full Round Head 22 Degree Framing Nailer

70-120PSI. Shoots 2”-3-1/2” 16d . 6.2 SCFM@90PSI. Contact or sequential.

Tool-less depth adjustment. 73 nail magazine capacity. Weighs 8.3lbs

229.00

AN902 3-1/2” Framing Coil Nailer

60-120PSI. Shoots 1-3/4”-3-1/2” .066-.148”. 5.6 SCFM@90PSI. Contact or

sequential. 150-300 nail magazine capacity. Weighs 7.7lbs

399.00

AN613 2-1/2” Siding Coil Nailer

70-120PSI. Shoots 1-1/2”-2-1/2” .090-.099”. 3.2 SCFM@90PSI. Contact or

sequential. 300 nail magazine capacity. Weighs 5.1lbs

369.00

AN454 1-3/4” Roofing Coil Nailer

70-120PSI. Shoots 3/4”-1-3/4”, .120 diameter. 3.7 SCFM@90PSI. Contact

or sequential. 120 nail magazine capacity. Weighs 5.2lbs

259.00

AC001 Compact Air Compressor

1/6hp induction motor. .58CFM@40PSI and .45CFM@90PSI . Up to

125psi. 1gal tank. Low noise and low amp draw. Weighs 21.3lbs

175.00

Pneumatics & Vacuums

28

MAC2400 2.5 HP Air Compressor

Low amp. 1720 RPM. 4.8CFM@40PSI and 4.2CFM@90PSI . Oil lubricated

cast iron pump. 130PSI max pressure. 4.2gal tank (twin) . Weighs 77 lbs

319.00

2021 your #1 source catalog for the complete line of

Documents