Greg Dallman 1506 12th Avenue North – Princeton, MN 55371

Cell: 763-234-2350 – Greg.Dallman@gmail.com

Experience

Greatbatch Medical February 2013 – Present Senior PD/Manufacturing Engineering Technician Minneapolis, MN

o Write and execute IQ protocols and reports for new and existing equipment. o Support all aspects of the Micro and Introducer molding areas. o Installed 2Vacuum Furnaces. o Performed the site acceptance test for both furnaces. o Perform Temperature Uniformity Surveys, Control/Over Temperature SAT’s, Load Thermocouple SAT’s and Vacuum

System verifications. o Tuned the PID controller to optimize control after a case of integral windup. o Authored all of the preventative maintenance procedures for both furnaces, industrial degreasers and automated parts

washing system. o Leak detection using PHOENXL 300. o Keep daily records of preventative maintenance actions Boston Scientific Cardio Rhythm Management September 2008 – November 2012 PD/Manufacturing Engineering Technician IV – Batteries and Leads Manufacturing St. Paul, MN o Perform Equipment Evaluations. o Execute and ensure calibrations and PM’s are performed on time. o Coordinate with the Metrology lab for equipment being sent out for calibration and vendor approval. o Proficient with measuring devices i.e., calipers, pin gauges, micrometers, etc. o Coordinate with the model shop for repair and manufacture of parts. o Troubleshoot equipment and correct issues. o Provide manufacturing with little or no down time.

Boston Scientific Scimed, Inc September 2002 – 2008 R&D Engineering Technician III – Cardiovascular Maple Grove, MN o Co-inventor Embolic Protection Devices with an Improved Filter Membrane. o Vascular Protection – Transferred Rubicon and next generation filter wire technologies from Mountain View, Ca. to Maple

Grove. o Developed Intellectual Property and submitted for patent approval. Nine patents pending approval. o Creation of parts and fixture drawings using Solidworks. o New product testing and design - Creation and development of standards for product performance. o Test Method Development- Design of fixtures and test procedures to ensure cardiovascular products comply with FDA and

internal specifications. o Statistical analysis of data, DOE, Gage R&R. o Drafting and design of parts and assemblies in Solidworks software. o Troubleshooting and maintenance of Track and Full Length Catheter Testers. o Writing technical reports, qualifications, and production processes. Progress Casting Group, Inc. February 2002 – September 2002 Non-Destructive Test Technician Plymouth, MN o Performed X-Ray and Liquid Penetrant inspection on aircraft, military missile parts and Harley Davidson engines.

Graco August 1996 – February 2002 R&D Engineering Technician III – Industrial and Automotive Engineering Division Minneapolis, MN

o Developed and built various test fixtures to allow automated testing of pumps, valves, spray guns, pneumatic components and electronic equipment.

o Documented results and recommended corrective actions o Work side by side with engineering and marketing to design equipment to meet customer requirements Curt’s Stump Removal May 1994 – August 1996 Co-Owner/Operator Minnetonka, MN o Maintained equipment. o Operated stump grinders o Provided estimates for customers. Systems Research Laboratories November 1993 – May 1994 Oklahoma City Site Manager Dayton, OH o Responsible for all of SRL's automated Eddy Current inspection systems for maintenance, repair, inspection plan

verification, test scheduling, software and hardware updates. o Collected, evaluated and relayed inspection data back to the main plant for corrective action. General Electric – Aircraft Engine Division September 1985 – April 1993 Field Service Representative Cincinnati, OH. o Designed and wrote inspection plans for G.E.'s automated Eddy Current inspection systems for aircraft engine hardware. o Collected, evaluated and relayed inspection data back to the main plant for corrective action. o Responsible for all NDT requirements for all engine models o Maintained all G.E.'s automated Eddy Current inspection systems with little down time. o Utilized a wide variety of manual and automated lab equipment. Education

o NORTH HENNEPIN COMMUNITY COLLEGE: Brooklyn Park, MN.

General studies related to mechanical engineering.

o HUTCHINSON TECHNICAL COLLEGE: Hutchinson, MN. Associate Applied Science Degree. Areas of study included,(but not limited to) : Manufacturing Processes, Physical Metallurgy, Blueprint Interpretation, Quality Control and Techniques in Nondestructive Testing.

o WRIGHT TECHNICAL COLLEGE : Buffalo, MN. Welding Degree.

o ANNANDALE PUBLIC HIGH SCHOOL : Annandale, MN. Diploma.

References

Tim Swain R&D Technician St. Jude Medical 612-805-6714 Cindy Satterness Manager II Stratasys 952-294-1590 Kyle Hendrikson Engineer Boston Scientific 320-282-9536