02 software installation

Installation Manual iSite BTS3002C Integrated Mini BTS Table of Contents

Huawei Technologies Proprietary

i

Table of Contents

Chapter 9 Installing the Maintenance Software ......................................................................... 9-1 9.1 About This Chapter ............................................................................................................ 9-1 9.2 Introduction to the Maintenance Software Installation....................................................... 9-1

9.2.1 Installation Requirements........................................................................................ 9-2 9.2.2 Software Storage Media:......................................................................................... 9-2

9.3 Installation Procedure ........................................................................................................ 9-3 9.3.1 Installing the Public Module .................................................................................... 9-3 9.3.2 Installing the O&M Module .................................................................................... 9-10

9.4 Logging In to the O&M System........................................................................................ 9-19

Chapter 10 Installing the Operation Software .......................................................................... 10-1 10.1 About This Chapter........................................................................................................ 10-1 10.2 Introduction to the Operation Software Installation........................................................ 10-1

10.2.1 Software Storage Media...................................................................................... 10-1 10.2.2 Ways to Download Software ............................................................................... 10-1 10.2.3 Software Installation Sequence........................................................................... 10-2 10.2.4 Installation File Directory..................................................................................... 10-2

10.3 Installation Procedure .................................................................................................... 10-2 10.3.1 Remote Installation ............................................................................................. 10-2 10.3.2 Local Installation ................................................................................................. 10-8

10.4 Version Check.............................................................................................................. 10-13

Installation Manual iSite BTS3002C Integrated Mini BTS List of Figures


ii

List of Figures

Figure 9-1 Software setup wizard .......................................................................................... 9-3

Figure 9-2 Installing the public module .................................................................................. 9-4

Figure 9-3 Software license agreement interface .................................................................. 9-4

Figure 9-4 Components of the public module........................................................................ 9-5

Figure 9-5 Inputting user information..................................................................................... 9-5

Figure 9-6 Choosing a destination folder............................................................................... 9-6

Figure 9-7 Choose folder interface ........................................................................................ 9-6

Figure 9-8 Selecting components to be installed................................................................... 9-7

Figure 9-9 Select the program folder interface in the OMC system public module ............... 9-7

Figure 9-10 Configuring the IP address of the OMC server .................................................. 9-8

Figure 9-11 Configuring the IP address of the report server.................................................. 9-8

Figure 9-12 Configuring the IP address of the alarm server.................................................. 9-9

Figure 9-13 Starting copying files........................................................................................... 9-9

Figure 9-14 Copying files progress indicator ....................................................................... 9-10

Figure 9-15 Setup complete................................................................................................. 9-10

Figure 9-16 Software setup wizard ...................................................................................... 9-11

Figure 9-17 OMC system operation & maintenance module installation information.......... 9-11

Figure 9-18 Software license agreement ............................................................................. 9-12

Figure 9-19 Components of the O&M module ..................................................................... 9-12

Figure 9-20 Inputting the user information........................................................................... 9-13

Figure 9-21 Choosing a destination folder........................................................................... 9-14

Figure 9-22 Choosing a folder ............................................................................................. 9-14

Figure 9-23 Selecting components to be installed (a) ......................................................... 9-15

Figure 9-24 Selecting components to be installed (b) ......................................................... 9-15

Figure 9-25 Selecting sub-components ............................................................................... 9-16



iii

Figure 9-26 Prompt for installing the OMC SHELL.............................................................. 9-16

Figure 9-27 Select program folder interface in the OMC system operation & maintenance module........................................................................................................................... 9-17

Figure 9-28 Network configuration interface in the OMC system operation & maintenance module........................................................................................................................... 9-17

Figure 9-29 Enter the user information ................................................................................ 9-18

Figure 9-30 Check the installation information..................................................................... 9-18

Figure 9-31 Copying files ..................................................................................................... 9-19

Figure 9-32 Setup complete................................................................................................. 9-19

Figure 10-1 Local office information configuration interface ................................................ 10-3

Figure 10-2 BTS software configuration interface ............................................................... 10-3

Figure 10-3 Add configuration item interface ....................................................................... 10-4

Figure 10-4 BTS remote maintenance interface.................................................................. 10-5

Figure 10-5 Multi-site Software Load interface .................................................................... 10-5

Figure 10-6 DRU software loading progress........................................................................ 10-6

Figure 10-7 Warning message for software loading ............................................................ 10-6

Figure 10-8 Loading the DRU software ............................................................................... 10-7

Figure 10-9 Activating the DRU software............................................................................. 10-7

Figure 10-10 Activating the DRU software successfully ...................................................... 10-8

Figure 10-11 BTS local maintenance console ..................................................................... 10-9

Figure 10-12 Communication failed..................................................................................... 10-9

Figure 10-13 Set communication port parameter interface ............................................... 10-10

Figure 10-14 User login interface....................................................................................... 10-10

Figure 10-15 Getting site management right ..................................................................... 10-11

Figure 10-16 Downloading software .................................................................................. 10-11

Figure 10-17 Loading software successfully...................................................................... 10-12

Figure 10-18 Software activation dialog box......................................................................10-12

Figure 10-19 Activating the software successfully ............................................................. 10-13

Figure 10-20 BTS remote maintenance console ............................................................... 10-14



iv

Figure 10-21 Getting the site SW version.......................................................................... 10-14

Figure 10-22 Board O&M interface .................................................................................... 10-15

Figure 10-23 Managing the IOMU board ........................................................................... 10-15

Figure 10-24 Querying the software version...................................................................... 10-16

Installation Manual iSite BTS3002C Integrated Mini BTS

Software InstallationChapter 9 Installing the Maintenance Software


9-1

Chapter 9 Installing the Maintenance Software

9.1 About This Chapter

This chapter describes how to install the maintenance software for the BTS3002C. It consists of the following sections:

z Introduction to the Maintenance Software Installation z Installation Procedure z Logging In to the O&M System

9.2 Introduction to the Maintenance Software Installation

I. Local Maintenance and Remote Maintenance

The maintenance software refers to the software running on the BTS3002C operation and maintenance (O&M) terminal.

The local maintenance is implemented by directly connecting the maintenance terminal to the BTS3002C through the Man Machine Interface (MMI).

The remote maintenance is implemented by connecting the maintenance terminal to the BTS3002C through the Abis interface.

II. Installation Sequence

The installation sequence is as follows:

1) Install the maintenance software. For the local maintenance, install the O&M module only. For the remote maintenance, install the public module besides the public module.

2) Install the operation software through the O&M terminal.

Note: This manual describes the software installation in a step-by-step manner. For the actual installation steps not mentioned in this manual, use the default settings. That is, click the Next or OK directly.




9-2

9.2.1 Installation Requirements

I. Hardware Requirements

Minimum configuration:

z CPU:PII 450 z Memory: 64 MB z Hard disk: 4 GB z Graphic memory: 8 MB z Resolution: 800x600 pixels z Network card z 1.44 MB floppy drive or CD-ROM

Recommended configuration:

z CPU: PIII 866 z Memory: 128 MB z Hard disk: 20 GB z Graphic memory: 16 MB z Resolution: 1024x768 pixels z Network card z 1.44 MB floppy drive or CD-ROM

II. Operating System

Windows 98

III. Others

TCP/IP protocol supported

Serial ports available

9.2.2 Software Storage Media:

The BTS maintenance software can be stored in:

z Floppy disk (1.44 MB) z CD-ROM




9-3

9.3 Installation Procedure

9.3.1 Installing the Public Module

If the software is stored in the floppy disk, insert the first floppy disk and then insert the rest disks according to the prompt.

If the software is stored in the CD-ROM, install the software according to the following steps:

1) Insert the CD-ROM and execute the Setup.exe file under the directory of the public module. The installation wizard is displayed, as shown in Figure 9-1.

Figure 9-1 Software setup wizard

2) In the Welcome! dialog box, as shown in Figure 9-2, click Next.




9-4

Figure 9-2 Installing the public module

The Software License Agreement dialog box is displayed, as shown in Figure 9-3.

Figure 9-3 Software license agreement interface

3) Click Yes, prompt information is displayed, as shown in Figure 9-4.




9-5

Figure 9-4 Components of the public module

4) Click Next to display the User Information dialog box, as shown in Figure 9-5. In the User Information dialog box, input the user name, company name, and product serial number.

Figure 9-5 Inputting user information




9-6

5) Click Next to display the Choose Destination Location dialog box, as shown in Figure 9-6.

Figure 9-6 Choosing a destination folder

You can click the Browse button to open the Choose Folder dialog box, as shown in Figure 9-7. In the Choose Folder dialog box, you can specify the OMC setup directories.

Figure 9-7 Choose folder interface




9-7

6) Set a destination folder and click Next in the Choose Destination Location dialog box to show the Choose Folder dialog box, as shown in Figure 9-8.

Figure 9-8 Selecting components to be installed

7) Click Next, a dialog box Select Program Folder is displayed, as shown in Figure 9-9. Input a folder name.

Figure 9-9 Select the program folder interface in the OMC system public module




9-8

8) Click Next to display the Network Configuration dialog box, as shown in Figure 9-10. Input the IP address of the OMC server.

Figure 9-10 Configuring the IP address of the OMC server

9) Click Next to open the Report system information configuration dialog box, as shown in Figure 9-11.

Figure 9-11 Configuring the IP address of the report server




9-9

10) Click Next to display the Alarm system information configuration window, as shown in Figure 9-12.

Figure 9-12 Configuring the IP address of the alarm server

11) Click Next to display the Start Copying Files dialog box, as shown in Figure 9-13.

Figure 9-13 Starting copying files

12) Click Next to display the Copying Files progress indictor, as shown in Figure 9-14.




9-10

Figure 9-14 Copying files progress indicator

13) After the files are copied, the Setup Complete dialog box is displayed, prompting you to restart this system, as shown in Figure 9-15.

14) Click Finish to complete the installation.

Figure 9-15 Setup complete

9.3.2 Installing the O&M Module

The procedure for installing the O&M module is basically the same as that of the public module.

The specific procedure is as follows:

1) Execute the Setup.exe under the directory of the O&M module. The installation wizard is displayed, as shown in Figure 9-16.




9-11

Figure 9-16 Software setup wizard

Figure 9-17 OMC system operation & maintenance module installation information

2) In the Welcome dialog box, as shown in Figure 9-17, click Next to display the Software License Agreement, as shown in Figure 9-18.




9-12

Figure 9-18 Software license agreement

3) Click Yes to display the Information dialog box, as shown in Figure 9-19.

Figure 9-19 Components of the O&M module

4) Click Next to display the User Information dialog box, as shown in Figure 9-20. Input the name, company, and serial number.




9-13

Figure 9-20 Inputting the user information

Note: Different products have different serial number.

5) Click Next to display the Choose Destination Location dialog box, as shown in Figure 9-21.




9-14

Figure 9-21 Choosing a destination folder

You can click the Browse button to open the Choose Folder dialog box, as shown in Figure 9-22, in which you may specify the directory to save the installation files.

Figure 9-22 Choosing a folder

6) After selecting the target folder, click Next in the Choose Destination Location dialog box, as shown in Figure 9-21. The Select Components dialog box is displayed, as shown in Figure 9-23.




9-15

Figure 9-23 Selecting components to be installed (a)

Pull down the scroll box in Figure 9-23, the interface as shown in Figure 9-24.

Figure 9-24 Selecting components to be installed (b)

7) In the Select Components dialog box, click the Change button to open the Select Sub-components dialog box to change the sub-components to be installed, as shown in Figure 9-25.




9-16

Figure 9-25 Selecting sub-components

8) Click Next in the Select Components dialog box. If the OMC Shell is not installed, the Select Components dialog box is displayed, as shown in Figure 9-26.

Figure 9-26 Prompt for installing the OMC SHELL

9) If choose "Exit this application" the installation is paused and exit the application. If the OMC Shell already exists in the system or choose "Continue" in Figure 9-26, click Next to open the Select Program Folder window as shown in Figure 9-27.




9-17

Figure 9-27 Select program folder interface in the OMC system operation & maintenance module

10) Click Next, a window Network Configuration will appear as shown in Figure 9-28. Input the IP address of the network server.

Figure 9-28 Network configuration interface in the OMC system operation & maintenance module

11) Click Next to show the Default user information for system to logon automation window, as shown in Figure 9-29. Enter the user information in this window.




9-18

Figure 9-29 Enter the user information

12) Click Next to shown the Start Copying Files window, as shown in Figure 9-30.

Figure 9-30 Check the installation information




9-19

13) Click Next, a window Copying Files will appear as shown in Figure 9-31.

Figure 9-31 Copying files

14) After the files are copied, the Setup Complete dialog box is displayed, prompting you to restart the computer, as shown in Figure 9-32.

15) Click Finish to complete the installation.

Figure 9-32 Setup complete

9.4 Logging In to the O&M System

After installing the maintenance software installation, start and log into the O&M system to check the installation.

1) Click Start > Programs > Huawei GSM-OMC > SITE Maintenance Terminal system to start the O&M system;

2) Select a communication port. If the site maintenance terminal can communicate with the BTS, it indicates that the BTS local maintenance software is successfully installed.


Software InstallationChapter 10 Installing the Operation Software


10-1

Chapter 10 Installing the Operation Software

10.1 About This Chapter

This chapter describes how to install the operation software for the BTS3002C. It consists of the following sections:

z Introduction to the Operation Software Installation z Installation Procedure z Version Check

10.2 Introduction to the Operation Software Installation

The Operation software is the signaling processing software that can operate the boards. The operation software consists of the IOMU software, DRU software and IASU software.

Running on the IOMU processor, the IOMU software performs O&M for the mini BTS and implement all access protocols.

The DRU software operating on the ITRU processor realizes power control, frequency hopping and interface control of the baseband module and RF module.

The IASU software runs on the processor of the optical transmission board and aims at function management on the mini BTS under optical transmission.

10.2.1 Software Storage Media

The BTS operation software can be stored in:

z Memory chip z Disk files

All memory chips in boards of ex-factory BTS are pre-installed with software (bootstrap software at least). Generally, the software is upgraded by software loading.

10.2.2 Ways to Download Software

In order to implement installation and upgrade of BTS3002C software, the system provides local and remote installation functions. As a result, the maintenance personnel can perform software installation or upgrading to IOMU, DRU and IASU through local or remote console.




10-2

The software installation is performed through the maintenance console.

10.2.3 Software Installation Sequence

There are two steps in software installation, loading and activation. Software loading refers to the action to send the software to be run to IOMU, and software activation means making the software on IOMU into effect.

To ensure smooth installation, please load BTS3002C software based on the following steps: IOMU software loading, activationDRU software loading, activationIASU software loading, activation.

10.2.4 Installation File Directory

The files to be downloaded can be saved under any directory in hard or soft disks. Specific file names and paths will not affect loading and activation. Nevertheless, it is still recommended that the files are named with category and version information (such as dru0820.bin stands for DRUs August 20 version binary file) to avoid misunderstanding and version errors. It is also recommended to set the file saving path as C:\OMC\BSC\BAM\dload.

10.3 Installation Procedure

10.3.1 Remote Installation

Before software loading, make sure the software to be loaded has been saved in the BAM of BSC, and corresponding software information has been configured in the BSC data configuration.

Steps for software information configuration:

1) Enter BSC auto data configuration console, and select Local office information tab page in the initial configuration interface as shown in Figure 10-1.




10-3

Figure 10-1 Local office information configuration interface

2) Click BTS Software Index, and a widow BTS software configuration is displayed, as shown in Figure 10-2.

Figure 10-2 BTS software configuration interface

3) Addition, deletion and modification of records can be implemented by clicking Add, Modify and Delete, as shown in Figure 10-2. By double clicking corresponding record, its detailed information can be viewed or configured. Figure 10-3 shows the detailed information of the first record in Figure 10-2. In the Software file name field, please input complete saving path and file name. The saving path here is a path relative to the BAM.




10-4

Figure 10-3 Add configuration item interface

Note: In BTS Software Configuration Item, the file name with the path, the active software version and the version time entered in should be the same with the practical saving directory and file name, otherwise, software loading will fail.

BTS remote installation is shown with DRU software loading.

4) Enter the BTS remote maintenance console as shown in Figure 10-4.




10-5

Figure 10-4 BTS remote maintenance interface

5) Select and double click Multi-site Software Load in the BTS remote maintenance interface, a window Multi-site Software Load is displayed in Figure 10-5.

Figure 10-5 Multi-site Software Load interface




10-6

Note: If the BTS is configured with various versions of the software, versions of the BTS operational software (including IOMU_MAIN, DRU_MAIN, IASU_MAIN) will be listed in the software loading dialog box for selection in different loading situations.

6) Select the DRU software and click Load to display a Software Load Procedure Indication interface, as shown in Figure 10-6. Click Close during loading, the user will see a Warning Message indicating that the software loading will go on while the loading progress will not be displayed, as shown in Figure 10-7.

Figure 10-6 DRU software loading progress

Figure 10-7 Warning message for software loading

7) If user does not click Close during loading, a "Load software successfully" message will be displayed on the interface when the loading progress reaches 100%, as shown in Figure 10-8. If clicking Close at this time, the user will also see a Warning Message shown in Figure 10-7, indicating that the software loading ends. Then the window Software Load Procedure Indication will close.




10-7

Figure 10-8 Loading the DRU software

8) Select and double click Multi-site Software Activation in the BTS remote maintenance interface to popup a window Multi-site Software Activation, as shown in Figure 10-9. Select the software version to be activated and input the board No. as required. Click OK to start activation.

Figure 10-9 Activating the DRU software




10-8

Caution:

Be sure to select the software version in consistency with the software loaded previously. Otherwise, the software installation or upgrade might fail.

9) Upon successful software activation, an "Activation request succeeded" message will be displayed in the Activation Result List. Click Close to end the DRU upgrading or installation. Refer to Figure 10-10.

Figure 10-10 Activating the DRU software successfully

Note: Upon successful software activation, the alarm system will display a board alarm for a short time. This is because the board is resetting after the software loading. Several seconds later, the alarm will disappear.

10.3.2 Local Installation

BTS local installation is shown with DRU software loading.

1) If MMI can communicate with the BTS, a window Site Maintenance Terminal System will pop up when user starts BTS local maintenance console software as shown in Figure 10-11.




10-9

Figure 10-11 BTS local maintenance console

2) If MMI cannot communicate with the BTS, a "Communication failed" message will be displayed as shown Figure 10-12. Please click Yes to enter into the window Set Communication Port Parameter as shown in Figure 10-12. In the window, select a communication port (COM1, COM2 or COM3) according to the actual situation and select the communication rate of 38400, then click OK.

Figure 10-12 Communication failed




10-10

Figure 10-13 Set communication port parameter interface

3) After establishing communication between the MMI and BTS, select the menu User management > User login to display a dialog box as shown in Figure 10-14. In the window, input the user name and user password in the corresponding fields and then click OK. If the user name and password input are correct, the dialog box will disappear and the user will successfully log into the system. Otherwise, a warning message pops up, indicating that wrong user name or password is input.

Figure 10-14 User login interface

4) Before loading the BTS local maintenance software, user should first get the site management right. Double click [Site/Site management right] and then in the popup window, click Get. Normally a prompt message "Getting site management right successfully" will be displayed as shown in Figure 10-15.




10-11

Figure 10-15 Getting site management right

5) Double click Force SW loading, and a window Software Dwonload is displayed. Fill in the following fields: File Name, Send Window Size (49 recommended), Version and File ID. For specific values for the fields, refer to the corresponding guidebook for upgrading. Click Begin, and the loading process will start as shown in Figure 10-16.

Figure 10-16 Downloading software

Note: Version and file ID must be correctly filled in, otherwise, the software cannot be loaded correctly, or software activation may be affected.

6) When the loading process has reached 100%, the indicating area of the dialog box will display "Load SW successfully" as shown in Figure 10-17.




10-12

Figure 10-17 Loading software successfully

7) Click Close button to close the loading dialog box. 8) Double click Software Activation and a window Software Activation is

displayed. Fill in the following fields: Version, Board No. and File ID, as shown in Figure 10-18.

Figure 10-18 Software activation dialog box

Caution:

Be sure to input the software version in consistency with the software loaded previously. Otherwise, the software installation or upgrade might fail.




10-13

9) Click OK. In normal cases, the system will prompt "SW activation confirmed" as shown in Figure 10-19.

Figure 10-19 Activating the software successfully

Note: Upon successful software activation, the alarm system will display a board alarm for a short time. This is because the board is resetting after the software loading. Several seconds later, the alarm will disappear.

10.4 Version Check

I. At the remote maintenance console

1) Enter the site structure tree of the BTS remote maintenance console as shown in Figure 10-20.




10-14

Figure 10-20 BTS remote maintenance console

2) Double click Get Site Software Version, and a window Get Site Software Version is displayed, as shown in Figure 10-21. All running board software versions on the site can be listed. The software version loaded can be checked.

Figure 10-21 Getting the site SW version




10-15

II. At the local maintenance console

At the local maintenance console, check the software version by viewing the board information. Take IOMU for example:

1) Enter the site structure tree of the BTS local maintenance console as shown in Figure 10-20.

2) Click the board in the tree structure to display the corresponding commands in the right pane as shown in Figure 10-22.

Figure 10-22 Board O&M interface

3) Double click Board > Board management to display a Board Management interface. Right click the IOMU board to show a float menu as shown in Figure 10-23.

Figure 10-23 Managing the IOMU board




10-16

4) Click Board information in the floating menu to display the Board Information interface. In the interface, the required board software version is displayed as shown in Figure 10-24.

Figure 10-24 Querying the software version

Table of ContentsList of FiguresChapter 9 Installing the Maintenance Software9.1 About This Chapter9.2 Introduction to the Maintenance Software Installation9.2.1 Installation Requirements9.2.2 Software Storage Media:

9.3 Installation Procedure9.3.1 Installing the Public Module9.3.2 Installing the O&M Module

9.4 Logging In to the O&M System

Chapter 10 Installing the Operation Software10.1 About This Chapter10.2 Introduction to the Operation Software Installation10.2.1 Software Storage Media10.2.2 Ways to Download Software10.2.3 Software Installation Sequence10.2.4 Installation File Directory

10.3 Installation Procedure10.3.1 Remote Installation10.3.2 Local Installation

10.4 Version Check

02 software installation

Documents